Scribd
Upload
143 views3 pages

Transient Response of LCR

The document describes an experiment to study the transient response of a series LCR circuit under different conditions. It provides background information and instructions for setting up the circuit with various component values to produce overdamped, critically damped, and underdamped responses. Measurements of voltage over time will be made and compared to theoretical predictions.

Uploaded by

AnkitMishra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
143 views3 pages

Transient Response of LCR

The document describes an experiment to study the transient response of a series LCR circuit under different conditions. It provides background information and instructions for setting up the circuit with various component values to produce overdamped, critically damped, and underdamped responses. Measurements of voltage over time will be made and compared to theoretical predictions.

Uploaded by

AnkitMishra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

TRANSIENT LCR CIRCUIT

EXPERIMENT 6: TRANSIENT RESPONSE OF A SERIES LCR CIRCUIT 10/14/03

In this experiment we will study the transient response of a series LCR circuit in the critically damped,
overdamped, and underdamped cases. For the overdamped case we will determine the decay constant,
while for the underdamped case we will measure the natural frequency, the damping constant, and the
Q factor.

Before coming to the laboratory make sure you understand the following material. For the circuit
shown below, suppose the switch S has been closed for a long time so that vC, vL, and vR have all
reached their asymptotic values. What values will vC, vL and vR take on at this point? (Write the
answer and a brief explanation in your notebook.) Now suppose that at time t = 0 the switch is opened.
Write down the initial conditions for the current i(t) and its time derivative di/dt just after the svitch
opens.

When the switch is open the current flowing in the circuit must satisfy the differential equation:

d 2i R di 1
+ + i = 0.
dt 2 L dt LC

The solutions to this equation will be discussed in class, and can also be found in some text books. In
your notebook you should write down the solutions to the differential equation for i(t) as a function of
the time for the underdamped, critically damped, and overdamped cases. In addition, write down
expressions for vR, vL and vC for the underdamped case.

1
TRANSIENT LCR CIRCUIT

All measurements are to be made with an oscilloscope using X10 attenuator probes. Note that by using
values of R that are too small you can obtain circuits with very high Q's and high voltages (that blow
out scopes and cause shocks). In particular be careful that you do not inadvertently set R to zero.

Construct the circuit as shown in the diagram above. Use a DC power supply set to about 3 V for V0.
Do not ground either terminal of the power supply (the circuit will be grounded at various points
depending on how you attach the scope). Adjust the current control on the power supply to limit the
current to about 0.5 A (this can be done by simply shorting the + and − terminals together and reading
the current meter on the supply). The switch is a mercury wetted relay which is driven by the AC
power lines (use terminals 3 and 4). The switch opens and closes 60 times a second. Use decade boxes
for R, L, and C. Note that on the capacitance decade boxes, MF means 10-6 F.

1. Set L = 10 mH, C = 100 nF and R = 50 Ω. Make rough sketches of vR(t), vL(t) and vC(t) for one
complete cycle of the switch. (NOTE: We adopt the convention that vR, vL and vC are all to be
measured in the counter-clockwise sense around the LCR loop, as shown in the circuit diagram.)
Indicate on your sketches the points at which the switch opens and closes. What are the observed
asymptotic values of vR, vL and vC for the switch-closed portion of the cycle?

2. When the switch is closed, the capacitor charges up quickly and thus vC reaches its equilibrium
value in a very short time. However, vR rises to its asymptotic value much more slowly. Make a
rough measurement of the time it takes for vR to come to (1 − e-1)V0, where V0 is its asymptotic
value, and compare your measurement with the expected time constant.

In the remaining sections we will focus on what happens during the switch-open part of the cycle.

3. (a) For a fixed value of L and C, experimentally determine the critical damping resistance by
observing vR vs time on the scope. Compare the measured and calculated values of the critical
damping resistance.

(b) Determine vR as a function of t (out to at least V0/20) (with R at the critical damping value)
as accurately as you can from the scope. (This is a bit tricky to do. The main problem is that di/dt
is zero at t = 0, which makes it difficult to get the scope to trigger right at t = 0. Try using vL or vC
to trigger to scope.) Record the results in a table and make a graph of vR vs t on semilog graph
paper with vR plotted on the logarithmic axis. Compare your measurements of vR with the
theoretical prediction, vR(t) = V0 (1 + γt)exp(−γt) , where γ = R/2L, and R is the value used in
your circuit.

2
TRANSIENT LCR CIRCUIT

4. (a) Next increase R by a factor of 5 or 10 to produce overdamped behavior. Measure and


tabulate vR as a function of t and graph the results (on semilog paper).

(b) Use a ruler to draw a straight line through the measured points and determine the decay
constant, γ. Compare your measured decay constant with the expected value,

γ = (R/2L) [1 − (1 − (4L/R2C))1/2)].

5. (a) Choose values for R, L, and C to produce underdamped behavior with a period T  60 µs
and with Q  6.

Make careful sketches or photographs of vR, vL and vC as a function of time from t = 0 out to t =
250 µs. Make sure that you get the relative phase of the signals right and that the signs are correct
(vL + vR + vC should be zero for all t).

(b) Make a list of the zero crossing times of vR(t) and determine the period and angular
frequency (ω) of the oscillation. Compare your result with the expected value,

ω = [(1/LC) - (R2/4L2)]1/2 .

(c) Make a list of the extrema (both positive and negative) of vC. Plot the resulting values of
|vC| as a function of t (on semilog paper) and determine the decay constant γ. Compare your result
with the expected value, γ = R/2L.

(d) The Q of the circuit can be determined from the magnitude of the first extremum in vL.
Note that the formula for vL can be written in the form:

⎡ ⎛γ⎞ ⎤
2

v L (t) = − V0 Q ⎢1 + ⎜ ⎟ ⎥ exp(− γt) sin ωt .


⎢⎣ ⎝ ω ⎠ ⎥⎦

At the first extremum (ωt = π/2) we have:

⎡ ⎛ γ ⎞2 ⎤ πγ
v L = − V0 Q ⎢1 + ⎜ ⎟ ⎥ exp(− ) .
⎣⎢ ⎝ ω ⎠ ⎦⎥ 2ω

Use this formula and your measured values of γ and ω to determine Q. Compare your result with
the expected value, Q = ωL/R where the formula for ω is given in (b) above.

You might also like