Application Form Design Approval of Type B Package

APPLICATION FOR PACKAGE DESIGN APPROVAL FOR
TRANSPORT OF RADIOACTIVE MATERIAL
(This form shall be duly filled in by the designer / consignor who proposes to deploy the
packaging for transport of radioactive materials and submitted to the Atomic Energy
Regulatory Board. It should be ensured that the necessary submissions such as the Safety
Analysis Report (SAR) and a cut-away sketch of 21 cm x 30 cm showing make-up of the
packaging are attached along with the application. The SAR shall contain details of analyses /
tests to demonstrate compliance with the regulatory design requirements. No para should be
left blank. If not applicable, write NA. Words and expressions used in this form shall have the
same meaning assigned to them in the Atomic Energy Regulatory Board Safety Code on
Transport)
Part 1: General Information
1.1 Name, address, telephone and fax : Mr. Vinod Kumar R V S/o, Veereshiyar Ramaswamy
number; and e-mail ID of the Applicant Tumkur, Karnataka State, India
:
:
1.2 Type of design approval required : Fast approval
1.3 Design approval required : First approval/Renewal
Part 2: Details of Radioactive Contents
2.1 Identity of radioactive material and its :

maximum strength in TBq
2.2 Whether it is a mixture of :
radionuclides, if yes the fraction of
activity concentration of
each radionuclide
2.3 Physical form :
2.4 Chemical form :
2.5 Special Form : Yes / No
2.6 If Yes, Certification Details,( if obtained :
already, attach copy of Certificate and
Special Form Test Reports)
2.7 Mass and volume of Contents :
2.8 Mass and volume of fissile material. (if :
applicable)
2.9 Fissile material composition with :
percent enrichment (if applicable)
2.10 Any other dangerous property :

Part 3: Packaging Details
3.1 Packaging model name :

3.2 Whether approved earlier : Yes / No
3.3 Competent authority identification mark :
if previously allocated.
3.4 Date of expiry of the Certificate issued by :
the competent authority, if applicable.
3.5 The gross mass of the package :
3.6 External dimension of the packaging :
(Relevant detailed drawings of the
containment system and also tie-down
should be attached.)
3.7 Whether there is any protruding feature on : Yes / No
the external surface of the packaging.
3.8 Whether behaviour of radioactive material : Yes / No
under varying conditions of temperature
and pressure have been taken into account
3.9 Whether the packaging is provided with : Yes / No
facilities for enabling safe handling
3.10 Whether the materials of the packaging : Yes / No
and components of structures are
physically and chemically compatible
with each other and with the package
contents, taking into account their
behaviour under irradiation
3.11 Whether the packaging material can : Yes / No
withstand temperature range of –40o C to
+70o C
3.12 Whether a cut-away sketch of dimensions : Yes / No
21 cm x 30 cm has been provided showing
make-up of the package
3.13 Whether specifications of packaging : Yes / No
construction materials have been attached
3.14 Whether the outer layer of the packaging : Yes / No
is designed to prevent the collection and
retention of water
3.15. Whether the external surface of the : Yes / No
packaging is so designed as to facilitate
easy and swift decontamination
3.16 In case lifting attachments are included in : Yes / No / Not applicable
the design of the packaging, whether
such attachments are capable of
supporting the weight of the packaging
without imposing stresses on the structure
of the package, in excess of the yield
stresses of the relevant parts of the said
structure (snatch lifting taken into
consideration)
3.17 Whether the lifting attachments on the : Yes / No / Not applicable

outer surface of the packaging, which are
to be used to lift the package, are
removable during transport
3.18 Whether any other features on the outer : Yes / No / Not applicable
surface of the cask which are not designed
for lifting are inoperable for lifting during
transport
3.19 Whether the tie down attachments on the : Yes / No / Not applicable
package are so designed that under both
normal and accident conditions of
transport, the forces in these attachments
will not impair the ability of the package
to meet the requirements of the
regulations.
3.20 Whether neutron absorbers have been : Yes / No / Not applicable
provided, where applicable, if fissile
material is transported
3.21a Specification/code followed for Quality :
Assurance Programme in manufacture
of packaging,
Whether maintenance programme for

3.21b packaging is prepared Yes/No
3.22 Whether a feature such as seal is : Yes / No
incorporated on the exterior of the
package as proof against tamper.
3.23 Mode of Transport : Road / Rail / Air / Water /
Part 4: Containment System
4.1 Whether the containment system has : Yes / No

adequate leak-tightness
4.2 Whether the material of the containment : Yes / No
system is likely to be degraded by the
contents?
4.3 Whether the containment system is : Yes / No
capable of retaining its radioactive
contents under the reduction of ambient
pressure to 60 kPa
4.4 Whether pressure relief valves are : Yes / No
provided in the packaging
4.5 Whether the radioactive contents could : Yes / No / Not applicable
escape through valves other than pressure
relief valves and, if yes,
Whether such valves are protected against Yes/No/Not applicable
unauthorised operation and provided with
an enclosure to retain leakage
4.6 Whether radiolytic decomposition of the
liquids or other vulnerable materials and
the generation of gas by chemical reaction
and radiolysis have been taken into
account in the construction of the : Yes / No / Not applicable
containment system
4.7 Whether the fastening device of the : Yes / No / Not applicable
enclosure is designed in such a way as to
prevent unintentional opening and
opening by a pressure which may arise
within the package
4.8 In case the containment system forms a : Yes / No / Not applicable
separate unit of the packaging, whether it
is capable of being securely closed by a
positive fastening device which is
independent of any other part of the
packaging
4.9 Whether the package meets the additional : Yes / No / Not applicable
requirements for packages transported by
air
Part 5: Radiation shielding in the packaging
5.1 Shielding material and thickness :
5.2 Estimated maximum radiation level on : mSv/h

external surface of the package for
designed activity of the radioactive
content
5.3 Estimated maximum radiation level at 1 m : mSv/h

from the external surface of the package
for designed activity of the radioactive
content
5.4 Transport Index(TI) (estimated) :
Part 6: Package Analyses and Tests
6.1 Whether the package will be able to : Yes / No:

withstand effects of any acceleration,
vibration or vibration resonance which
may arise under routine conditions of
transport without any deterioration in the
closing devices on the various receptacles
or in the integrity of the package as a
whole, e.g. nuts, bolts, and other securing
devices becoming loose or being released
unintentionally, even after repeated use.
6.2 Whether evaluation has been done to : Yes / No
demonstrate design of the packaging
under normal and accident conditions of
transport as per the regulatory
requirements
6.3 Maximum temperature at any accessible :

surface of package in presence / absence
of insolation
6.4 Maximum surface heat flux (W/m2) :
6.5 The expected absolute maximum normal :

operating pressure(MNOP) of the
containment system
6.6 Whether details of actual tests on : Yes / No / Not applicable

prototype / scale model have been
provided
6.7 If calculation / analytical methods have : Yes / No / Not applicable
been used for demonstrating compliance
with test requirements, please state
whether the analysis is based on
computer codes validated by experiments
Part 7: Information required only for packages of fissile material
7.1 Whether at least two Water Barriers are : Yes / No/Not applicable
found effective under Accident conditions
7.2 Maximum number of package that remain :
subcritical under normal conditions of
transport
7.3 Maximum number of packages that :
remain subcritical under accident
conditions of transport specified for fissile
material
7.4 Criticality Safety Index(CSI) :
Part 8: Any other relevant information

Application Form Design Approval of Type B Package

Uploaded by

Copyright:

Available Formats

Application Form Design Approval of Type B Package

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Application Form Design Approval of Type B Package

Uploaded by

Copyright:

Available Formats

APPLICATION FOR PACKAGE DESIGN APPROVAL FOR

TRANSPORT OF RADIOACTIVE MATERIAL

Part 1: General Information

1.3 Design approval required : First approval/Renewal

Part 2: Details of Radioactive Contents

2.1 Identity of radioactive material and its :

2.10 Any other dangerous property :

3.1 Packaging model name :

3.17 Whether the lifting attachments on the : Yes / No / Not applicable

Whether maintenance programme for

Part 4: Containment System

4.1 Whether the containment system has : Yes / No

Part 5: Radiation shielding in the packaging

5.1 Shielding material and thickness :

5.2 Estimated maximum radiation level on : mSv/h

5.3 Estimated maximum radiation level at 1 m : mSv/h

Part 6: Package Analyses and Tests

6.1 Whether the package will be able to : Yes / No:

6.3 Maximum temperature at any accessible :

6.5 The expected absolute maximum normal :

6.6 Whether details of actual tests on : Yes / No / Not applicable

Part 7: Information required only for packages of fissile material

Part 8: Any other relevant information

You might also like