EM GS 5220 Series v1.1

User’s Manual of GS-5220 Series
Trademarks
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
Energy Saving Note of the Device

This power required device does not support Standby mode operation. For energy saving, please remove the power cable to
disconnect the device from the power circuit. In view of saving the energy and reducing the unnecessary power consumption, it
is strongly suggested to remove the power connection for the device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET GS-5220 Series User's Manual
Model: GS-5220 Series
Revision: 1.0 (January, 2015)
Part No: EM-GS-5220-series _v1.0
2
TABLE OF CONTENTS
1. INTRODUCTION.................................................................................................................... 9
1.1 Packet Contents ...........................................................................................................................................9
1.2 Product Description ...................................................................................................................................10
1.3 How to Use This Manual ............................................................................................................................12
1.4 Product Features........................................................................................................................................13
1.5 Product Specifications ..............................................................................................................................16
2. INSTALLATION ................................................................................................................... 22
2.1 Hardware Description ................................................................................................................................22

2.1.1 Switch Front Panel ..............................................................................................................................................22
2.1.2 LED Indications ...................................................................................................................................................24
2.1.3 Switch Rear Panel ...............................................................................................................................................28
2.2 Installing the Switch...................................................................................................................................30

2.2.1 Desktop Installation .............................................................................................................................................30
2.2.2 Rack Mounting.....................................................................................................................................................31
2.2.3 Installing the SFP/SFP+ Transceiver ...................................................................................................................32
3. SWITCH MANAGEMENT .................................................................................................... 36
3.1 Requirements..............................................................................................................................................36
3.2 Management Access Overview .................................................................................................................37
3.3 Administration Console .............................................................................................................................38
3.4 Web Management .......................................................................................................................................39
3.5 SNMP-based Network Management .........................................................................................................40
3.6 PLANET Smart Discovery Utility ..............................................................................................................40
4. WEB CONFIGURATION ...................................................................................................... 42
4.1 Main Web Page ...........................................................................................................................................44
4.2 System.........................................................................................................................................................46
4.2.1 System Information..............................................................................................................................................47
4.2.2 IP Configuration ...................................................................................................................................................48
4.2.3 IP Status ..............................................................................................................................................................50
3
4.2.4 Users Configuration .............................................................................................................................................51
4.2.5 Privilege Levels ...................................................................................................................................................54
4.2.6 NTP Configuration ...............................................................................................................................................55
4.2.7 Time Configuration ..............................................................................................................................................56
4.2.8 UPnP ...................................................................................................................................................................58
4.2.9 DHCP Relay ........................................................................................................................................................60
4.2.10 DHCP Relay Statistics .......................................................................................................................................61
4.2.11 CPU Load ..........................................................................................................................................................63
4.2.12 System Log........................................................................................................................................................64
4.2.13 Detailed Log ......................................................................................................................................................65
4.2.14 Remote Syslog ..................................................................................................................................................66
4.2.15 SMTP Configuration ..........................................................................................................................................67
4.2.16 Web Firmware Upgrade.....................................................................................................................................68
4.2.17 TFTP Firmware Upgrade ...................................................................................................................................69
4.2.18 Save Startup Config...........................................................................................................................................70
4.2.19 Configuration Download ....................................................................................................................................70
4.2.20 Configuration Upload .........................................................................................................................................71
4.2.21 Configuration Activate........................................................................................................................................71
4.2.22 Configuration Delete ..........................................................................................................................................72
4.2.23 Image Select......................................................................................................................................................72
4.2.24 Factory Default ..................................................................................................................................................73
4.2.25 System Reboot ..................................................................................................................................................74
4.3 Simple Network Management Protocol....................................................................................................75

4.3.1 SNMP Overview ..................................................................................................................................................75
4.3.2 SNMP System Configuration ...............................................................................................................................76
4.3.3 SNMP Trap Configuration....................................................................................................................................78
4.3.4 SNMP System Information ..................................................................................................................................80
4.3.5 SNMPv3 Configuration ........................................................................................................................................81
4.3.5.1 SNMPv3 Communities ..............................................................................................................................81

4.3.5.2 SNMPv3 Users ..........................................................................................................................................82
4.3.5.3 SNMPv3 Groups........................................................................................................................................83
4.3.5.4 SNMPv3 Views..........................................................................................................................................84
4.3.5.5 SNMPv3 Access ........................................................................................................................................85
4.4 Port Management .......................................................................................................................................87

4.4.1 Port Configuration................................................................................................................................................87
4.4.2 Port Statistics Overview .......................................................................................................................................89
4.4.3 Port Statistics Detail.............................................................................................................................................90
4.4.4 SFP Module Information ......................................................................................................................................92
4.4.5 Port Mirror............................................................................................................................................................93
4
4.5 Link Aggregation ........................................................................................................................................96

4.5.1 Static Aggregation................................................................................................................................................98
4.5.2 LACP Configuration .............................................................................................................................................99
4.5.3 LACP System Status .........................................................................................................................................101
4.5.4 LACP Port Status...............................................................................................................................................102
4.5.5 LACP Port Statistics...........................................................................................................................................103
4.6 VLAN..........................................................................................................................................................104
4.6.1 VLAN Overview .................................................................................................................................................104
4.6.2 IEEE 802.1Q VLAN ...........................................................................................................................................105
4.6.3 VLAN Port Configuration ...................................................................................................................................108
4.6.4 VLAN Membership Status.................................................................................................................................. 114
4.6.5 VLAN Port Status............................................................................................................................................... 115
4.6.6 Port Isolation...................................................................................................................................................... 117
4.6.7 VLAN setting example: ...................................................................................................................................... 119
4.6.7.1 Two Separate 802.1Q VLANs.................................................................................................................. 119
4.6.7.2 VLAN Trunking between two 802.1Q aware switches .............................................................................121
4.6.7.3 Port Isolate ..............................................................................................................................................124
4.6.8 MAC-based VLAN .............................................................................................................................................125
4.6.9 MAC-based VLAN Status ..................................................................................................................................126
4.6.10 Protocol-based VLAN ......................................................................................................................................126
4.6.11 Protocol-based VLAN Membership..................................................................................................................128
4.7 Spanning Tree Protocol ...........................................................................................................................130

4.7.1 Theory ...............................................................................................................................................................130
4.7.2 STP System Configuration ................................................................................................................................136
4.7.3 Bridge Status .....................................................................................................................................................138
4.7.4 CIST Port Configuration.....................................................................................................................................139
4.7.5 MSTI Priorities ...................................................................................................................................................142
4.7.6 MSTI Configuration............................................................................................................................................143

4.7.7 MSTI Ports Configuration ..................................................................................................................................144
4.7.8 Port Status .........................................................................................................................................................146
4.7.9 Port Statistics.....................................................................................................................................................147
4.8 Multicast ....................................................................................................................................................148

4.8.1 IGMP Snooping .................................................................................................................................................148
4.8.2 Profile Table.......................................................................................................................................................152
4.8.3 Address Entry ....................................................................................................................................................153
4.8.4 IGMP Snooping Configuration ...........................................................................................................................154
4.8.5 IGMP Snooping VLAN Configuration.................................................................................................................156
4.8.6 IGMP Snooping Port Group Filtering .................................................................................................................158
4.8.7 IGMP Snooping Status ......................................................................................................................................159
5
4.8.8 IGMP Group Information....................................................................................................................................160
4.8.9 IGMPv3 Information...........................................................................................................................................161
4.8.10 MLD Snooping Configuration...........................................................................................................................162
4.8.11 MLD Snooping VLAN Configuration.................................................................................................................163
4.8.12 MLD Snooping Port Group Filtering.................................................................................................................165
4.8.13 MLD Snooping Status ......................................................................................................................................166
4.8.14 MLD Group Information ...................................................................................................................................167
4.8.15 MLDv2 Information ..........................................................................................................................................168
4.8.16 MVR (Multicaset VLAN Registration)...............................................................................................................169
4.8.17 MVR Status......................................................................................................................................................172
4.8.18 MVR Groups Information .................................................................................................................................173
4.8.19 MVR SFM Information .....................................................................................................................................173
4.9 Quality of Service .....................................................................................................................................175

4.9.1 Understanding QoS ...........................................................................................................................................175
4.9.2 Port Policing ......................................................................................................................................................176
4.9.3 Port Classification..............................................................................................................................................176
4.9.4 Port Scheduler...................................................................................................................................................178
4.9.5 Port Shaping......................................................................................................................................................179
4.9.5.1 QoS Egress Port Schedule and Shapers ................................................................................................180
4.9.6 Port Tag Remarking ...........................................................................................................................................181
4.9.6.1 QoS Egress Port Tag Remarking.............................................................................................................182
4.9.7 Port DSCP .........................................................................................................................................................183
4.9.8 DSCP-based QoS .............................................................................................................................................184
4.9.9 DSCP Translation ..............................................................................................................................................185
4.9.10 DSCP Classification.........................................................................................................................................186
4.9.11 QoS Control List...............................................................................................................................................187
4.9.11.1 QoS Control Entry Configuration ...........................................................................................................189
4.9.12 QCL Status ......................................................................................................................................................191
4.9.13 Storm Control Configuration ............................................................................................................................192

4.9.14 WRED..............................................................................................................................................................193
4.9.15 QoS Statistics ..................................................................................................................................................196
4.9.16 Voice VLAN Configuration ...............................................................................................................................196
4.9.17 Voice VLAN OUI Table.....................................................................................................................................199
4.10 Access Control Lists..............................................................................................................................200

4.10.1 Access Control List Status ...............................................................................................................................200
4.10.2 Access Control List Configuration....................................................................................................................202
4.10.3 ACE Configuration ...........................................................................................................................................204
4.10.4 ACL Ports Configuration ..................................................................................................................................214
4.10.5 ACL Rate Limiter Configuration .......................................................................................................................216
6
4.11 Authentication.........................................................................................................................................217
4.11.1 Understanding IEEE 802.1X Port-Based Authentication..................................................................................218
4.11.2 Authentication Configuration ............................................................................................................................221
4.11.3 Network Access Server Configuration..............................................................................................................222
4.11.4 Network Access Overview ...............................................................................................................................233
4.11.5 Network Access Statistics ................................................................................................................................234
4.11.6 RADIUS ...........................................................................................................................................................241
4.11.7 TACACS+ ........................................................................................................................................................243
4.11.8 RADIUS Overview ...........................................................................................................................................244
4.11.9 RADIUS Details ...............................................................................................................................................246
4.11.10 Windows Platform RADIUS Server Configuration..........................................................................................252
4.11.11 802.1X Client Configuration ...........................................................................................................................257
4.12 Security ...................................................................................................................................................260

4.12.1 Port Limit Control .............................................................................................................................................260
4.12.2 Access Management .......................................................................................................................................264
4.12.3 Access Management Statistics ........................................................................................................................265
4.12.4 HTTPs .............................................................................................................................................................266
4.12.5 SSH .................................................................................................................................................................267
4.12.6 Port Security Status .........................................................................................................................................267
4.12.7 Port Security Detail ..........................................................................................................................................270
4.12.8 DHCP Snooping ..............................................................................................................................................271
4.12.9 Snooping Table ................................................................................................................................................273
4.12.10 IP Source Guard Configuration......................................................................................................................273
4.12.11 IP Source Guard Static Table .........................................................................................................................275
4.12.12 ARP Inspection ..............................................................................................................................................276
4.12.13 ARP Inspection Static Table ...........................................................................................................................277
4.12.14 Dynamic ARP Inspection Table......................................................................................................................278
4.13 Address Table .........................................................................................................................................280

4.13.1 MAC Table Configuration.................................................................................................................................280
4.13.2 MAC Address Table Status ..............................................................................................................................282
4.14 LLDP ........................................................................................................................................................284

4.14.1 Link Layer Discovery Protocol .........................................................................................................................284
4.14.2 LLDP Configuration .........................................................................................................................................284
4.14.3 LLDP MED Configuration ................................................................................................................................287
4.14.4 LLDP-MED Neighbor .......................................................................................................................................293
4.14.5 Neighbor ..........................................................................................................................................................297
4.14.6 Port Statistics...................................................................................................................................................298
4.15 Network Diagnostics..............................................................................................................................300
7
4.15.1 Ping .................................................................................................................................................................301
4.15.2 IPv6 Ping .........................................................................................................................................................302
4.15.3 Remote IP Ping Test ........................................................................................................................................303
4.15.4 Cable Diagnostics............................................................................................................................................304
4.16 Loop Protection......................................................................................................................................306

4.16.1 Configuration ...................................................................................................................................................306
4.16.2 Loop Protection Status.....................................................................................................................................307
4.17 RMON.......................................................................................................................................................309
4.17.1 RMON Alarm Configuration .............................................................................................................................309
4.17.2 RMON Alarm Status......................................................................................................................................... 311
4.17.3 RMON Event Configuration .............................................................................................................................312
4.17.4 RMON Event Status.........................................................................................................................................313
4.17.5 RMON History Configuration ...........................................................................................................................314
4.17.6 RMON History Status.......................................................................................................................................315
4.17.7 RMON Statistics Configuration ........................................................................................................................316
4.17.8 RMON Statistics Status....................................................................................................................................317
5. SWITCH OPERATION ....................................................................................................... 319
5.1 Address Table ...........................................................................................................................................319
5.2 Learning ....................................................................................................................................................319
5.3 Forwarding & Filtering .............................................................................................................................319
5.4 Store-and-Forward ...................................................................................................................................319
5.5 Auto-Negotiation ......................................................................................................................................320
6. TROUBLESHOOTING....................................................................................................... 321
APPENDIX A: Networking Connection ............................................................................... 322
A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T........................................................322
A.2 10/100Mbps, 10/100BASE-TX..................................................................................................................322
APPENDIX B : GLOSSARY .................................................................................................. 324
8
1. INTRODUCTION
Thanks you for purchasing PLANET GS-5220 Managed Switch series, which comes with multiple Gigabit Ethernet copper and
SFP/SFP+ fiber optic connectibility and robust layer 2 and layer 4 features. The description of this model is shown below:
GS-5220-16S8C L2+ 24-port 100/1000BASE-X SFP + 8-port Shared TP Managed Switch
GS-5220-16S8CR L2+ 24-port 100/1000BASE-X SFP + 8-port Shared TP Managed Switch with AC/DC Redundant Power
GS-5220-44S4C L2+ 48-port 100/1000BASE-X SFP + 4-port Shared TP Managed Switch
GS-5220-46S2C4X L2+ 48-port 100/1000BASE-X SFP + 2-port Shared TP + 4-port 10G SFP Managed Switch
GS-5220-48T4X L2+ 48-port 10/100/1000BASE-T + 4-port Shared SFP + 4-port 10G SFP Managed Switch
“Managed Switch” is used as an alternative name in this user’s manual.
1.1 Packet Contents

Open the box of the Managed Switch and carefully unpack it. The box should contain the following items:
 The Managed Switch
 Quick Installation Guide
 RJ45 to RS232 Cable
 Rubber Feet
 Two Rack-mounting Brackets with Attachment Screws
 Power Cord
 SFP Dust-proof Caps
Model Name SFP Dust-proof Caps
GS-5220-16S8C(R) 24
GS-5220-44S4C 48
GS-5220-46S2C4X 52
GS-5220-48T4X 8
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
9
1.2 Product Description

Ideal Combination of 10G Uplink, high-density, Gigabit and Layer 3 Static Routing
PLANET GS-5220 series is a Layer 2+ managed Gigabit / 10 Gigabit Ethernet switch and supports static Layer 3 routing in a
1U case. The GS-5220 series can handle extremely large amounts of data in a secure topology linking to an enterprise
backbone or high capacity servers.
Layer 3 IPv4 and IPv6 VLAN Routing for Secure and Flexible Management
The GS-5220 series switch not only provides ultra high transmission performance, and excellent layer 2 and layer 4
technologies, but also layer 3 IPv4/IPv6 VLAN routing feature which allows to cross over different VLANs and different IP
addresses for the purpose of having a highly-secured, flexible management and simpler networking application.
IPv6 / IPv4 Dual Stack

Supporting both IPv6 and IPv4 protocols, the GS-5220 series helps the SMBs to step in the IPv6 era with the lowest investment
as its network facilities need not to be replaced or overhauled if the IPv6 FTTx edge network is set up.
Robust Layer 2 Features
The GS-5220 series can be programmed for advanced switch management functions such as dynamic port link aggregation,
Q-in-Q VLAN, private VLAN, Multiple Spanning Tree protocol (MSTP), Layer 2 to Layer 4 QoS, bandwidth control and
IGMP/MLD Snooping. Via the link aggregation of supporting ports, the GS-5220 series allows the operation of a high-speed
trunk to combine with multiple fiber ports and supports fail-over as well.
Powerful Security
The GS-5220 series offers a comprehensive layer 2 to layer 4 Access Control List (ACL) for enforcing security to the edge. It
can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or
defined typical network applications. Its protection mechanism also comprises 802.1X Port-based and MAC-based user and
device authentication. With the private VLAN function, communication between edge ports can be prevented to ensure user
privacy. The GS-5220 series also provides DHCP Snooping, IP Source Guard and Dynamic ARP Inspection functions to
prevent IP snooping from attack and discard ARP packets with invalid MAC address. The network administrators can now
construct highly secured corporate networks with considerably less time and effort than before.
Excellent Traffic Control

The GS-5220 series is loaded with powerful traffic management and QoS features to enhance connection services by SMBs.
The QoS features include wire-speed Layer 4 traffic classifiers and bandwidth limit that are particular useful for multi-tenant unit,
multi business unit, Telco, or Network Service Provider’s applications. It also empowers the enterprises to take full advantages
of the limited network resources and guarantees the best performance in VoIP and video conferencing transmission.
10
Efficient and Secure Management

The GS-5220 series Managed Switch is equipped with console, Web and SNMP management interfaces. With the built-in
Web-based management interface, the GS-5220 series offers an easy-to-use, platform-independent management and
configuration facility. The GS-5220 series supports standard Simple Network Management Protocol (SNMP) and can be
managed via any management software based on standard of SNMP protocol. For reducing product learning time, the GS-5220
series offers Cisco-like command via Telnet or console port and customer doesn’t need to learn new command from these
switches. Moreover, the GS-5220 series offers secure remote management by supporting SSH, SSL and SNMPv3 connection
which encrypt the packet content at each session.
Flexibility and Extension Solution

The mulit-mini-GBIC slots built in the GS-5220 series series support dual speed as it features 100BASE-FX and
1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules. Now the administrator can flexibly choose the
suitable SFP transceiver according to not only the transmission distance, but also the transmission speed required. The
distance can be extended from 550 meters to 2km (multi-mode fiber) up to above 10/20/30/40/50/70/120 kilometers
(single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.
Intelligent SFP Diagnosis Mechanism

The GS-5220 series supports SFP-DDM (Digital Diagnostic Monitor) function that greatly helps network administrator to
easily monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias
current, and transceiver supply voltage.
11
1.3 How to Use This Manual

This User’s Manual is structured as follows:
Section 2, INSTALLATION
The section explains the functions of the Managed Switch and how to physically install the Managed Switch.
Section 3, SWITCH MANAGEMENT

The section contains the information about the software function of the Managed Switch.
Section 4, WEB CONFIGURATION

The section explains how to manage the Managed Switch by Web interface.
Section 5, SWITCH OPERATION

The chapter explains how to do the switch operation of the Managed Switch.
Section 6, POWER over ETHERNET OVERVIEW

The chapter introduces the IEEE 802.3af / 802.3at PoE standard and PoE provision of the Managed Switch.
Section 7, TROUBLESHOOTING
The chapter explains how to do troubleshooting of the Managed Switch.
Appendix A
The section contains cable information of the Managed Switch.
12
1.4 Product Features

 Physical Port
 10/100/1000BASE-T Gigabit RJ45 copper
 100/1000BASE-X mini-GBIC/SFP slots
 1000BASE-X / 10GBASE-X mini-GBIC/SFP+ slots (For GS-5220-46S2C4X, GS-5220-48T4X)

 RJ45 console interface for switch basic management and setup
 Layer 2 Features
 Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
 High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize
the network bandwidth
 Storm Control support

 Broadcast / Unicast / Unknown-unicast
 Supports VLAN
 IEEE 802.1Q tagged VLAN
 Up to 255 VLANs groups, out of 4094 VLAN IDs
 Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
 Private VLAN Edge (PVE)
 Protocol-based VLAN
 MAC-based VLAN
 IP Subnet-based VLAN
 Voice VLAN
 Supports Spanning Tree Protocol

 STP, IEEE 802.1D Spanning Tree Protocol
 RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
 MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
 BPDU Guard
 Supports Link Aggregation

 802.3ad Link Aggregation Control Protocol (LACP)
 Cisco ether-channel (Static Trunk)
 Up to 8 ports per trunk group
 Up to 16Gbps bandwidth (full duplex mode)
 Provides port mirror (many-to-1)
 Port mirroring to monitor the incoming or outgoing traffic on a particular port
 Loop protection to avoid broadcast loops
 Layer 3 IP Routing Features

 Supports maximum 32 static routes and route summarization
13
 Quality of Service
 Ingress Shaper and Egress Rate Limit per port bandwidth control
 8 priority queues on all switch ports
 Traffic classification
- IEEE 802.1p CoS
- TOS / DSCP / IP Precedence of IPv4/IPv6 packets
- IP TCP/UDP port number
- Typical network application
 Strict priority and Weighted Round Robin (WRR) CoS policies
 Traffic-policing policies on the switch port
 DSCP remarking
 Multicast
 Supports IGMP Snooping v1, v2 and v3
 Supports MLD Snooping v1 and v2
 Querier mode support
 IGMP Snooping port filtering
 MLD Snooping port filtering
 MVR (Multicast VLAN Registration)
 Security
 Authentication
- IEEE 802.1x Port-based / MAC-based network access authentication
- IEEE 802.1x Authentication with Guest VLAN
- Built-in RADIUS client to cooperate with the RADIUS servers
- RADIUS / TACACS+ users access authentication
 Access Control List
- IP-based Access Control List (ACL)
- MAC-based Access Control List (ACL)
 Source MAC / IP address binding
 DHCP Snooping to filter distrusted DHCP messages
 Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
 IP Source Guard prevents IP spoofing attacks

 IP address access management to prevent unauthorized intruder
 Management
 IPv4 and IPv6 dual stack management
 Switch Management Interfaces

- Console / Telnet Command Line Interface
- Web switch management
- SNMP v1, v2c, and v3 switch management
- SSH / SSL secure access
14
 IPv6 Address / NTP management
 Built-in Trivial File Transfer Protocol (TFTP) client
 BOOTP and DHCP for IP address assignment
 System Maintenance
- Firmware upload / download via HTTP / TFTP
- Reset button for system reboot or reset to factory default
- Dual Images
 DHCP Relay and Option 82
 User Privilege levels control
 NTP (Network Time Protocol)
 Link Layer Discovery Protocol (LLDP) and LLDP-MED
 Network Diagnostic
- SFP-DDM (Digital Diagnostic Monitor)
- Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
- ICMPv6 / ICMPv4 Remote Ping
 SMTP / Syslog remote alarm
 Four RMON groups (history, statistics, alarms and events)
 SNMP trap for interface Link Up and Link Down notification
 System Log
 PLANET Smart Discovery Utility for deploy management
 Redundant Power System (GS-5220-16S8CR)

■ 100~240V AC / 36-60V DC Dual power redundant
■ Active-active redundant power failure protection
■ Backup of catastrophic power failure on one supply

■ Fault tolerance and resilience.
15
1.5 Product Specifications

GS-5220-16S8C / GS-5220-16S8CR
Product GS-5220-16S8C GS-5220-16S8CR
Hardware Specifications
Copper Ports 8 10/ 100/1000BASE-T RJ45 Auto-MDI/MDI-X ports, shared with Port-1~Port-8
SFP/mini-GBIC Slots 24 100/1000BASE-X Dual Speed SFP interfaces
Console 1 x RS232-to-RJ45 serial port (115200, 8, N, 1)
Switch Architecture Store-and-Forward
Switch Fabric 48Gbps / non-blocking
Throughput 35.7Mpps@64Bytes
Address Table 16K entries, automatic source address learning and ageing
Share Data Buffer 16M bits

IEEE 802.3x pause frame for full-duplex
Flow Control
Back pressure for half-duplex
Jumbo Frame 10K bytes
< 5 sec: System reboot
Reset Button
> 5 sec: Factory default
Dimensions (W x D x H) 440 x 200 x 44.5 mm, 1U height
Weight 2745g
Power Requirements – AC AC 100~240V, 50/60Hz
48V DC @ 0.6A nominal voltage

Power Requirements – DC ---
Operating Range: 36 ~ 60V DC
Power Consumption 45 watts / 153 BTU ( max.)
ESD Protection 6KV DC

Layer 2 Functions
Port disable / enable
Port Configuration Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable / enable
Display each port’s speed duplex mode, link status, flow control status,
Port Status
auto-negotiation status, trunk status
TX / RX / Both
Port Mirroring
Many-to-1 monitor
802.1Q agged based VLAN
Q-in-Q tunneling
Private VLAN Edge (PVE)
MAC-based VLAN
VLAN Protocol-based VLAN
Voice VLAN
IP Subnet-based VLAN
MVR (Multicast VLAN registration)
Up to 255 VLAN groups, out of 4094 VLAN IDs
IEEE 802.3ad LACP / static trunk
Link Aggregation
12 groups of 8-port trunk supported
Spanning Tree Protocol STP, IEEE 802.1D Spanning Tree Protocol
16
RSTP, IEEE 802.1w Rapid Spanning Tree Protocol

MSTP, IEEE 802.1s Multiple Spanning Tree Protocol
Traffic classification based, strict priority and WRR
8-Level priority for switching
- Port Number
QoS
- 802.1p priority
- 802.1Q VLAN tag
- DSCP/TOS field in IP packet
IGMP (v1/v2/v3) snooping, up to 255 multicast groups
IGMP Snooping
IGMP querier mode support
MLD (v1/v2) snooping, up to 255 multicast groups
MLD Snooping
MLD querier mode support
IP-based ACL / MAC-based ACL
Access Control List
Up to 256 entries
Per port bandwidth control
Bandwidth Control Ingress: 100Kbps~1000Mbps
Egress: 100Kbps~1000Mbps
Layer 3 Functions
IP Interfaces Max. 128 VLAN interfaces
Routing Table Max. 32 routing entries
IPv4 hardware static routing

Routing Protocols
Management
Basic Management Interfaces Console / Telnet / Web browser / SNMP v1, v2c
Secure Management Interfaces SSH, SSL, SNMP v3
RFC-1213 MIB-II
RFC-1493 Bridge MIB
RFC-1643 Ethernet MIB
RFC-2863 Interface MIB
RFC-2665 Ether-Like MIB
RFC-2819 RMON MIB (Group 1, 2, 3 and 9)
RFC-2737 Entity MIB
RFC-2618 RADIUS Client MIB
SNMP MIBs
RFC-2863 IF-MIB
RFC-2933 IGMP-STD-MIB
RFC-3411 SNMP-Frameworks-MIB
RFC-4292 IP Forward MIB
RFC-4293 IP MIB
RFC-4836 MAU-MIB
IEEE 802.1X PAE
LLDP
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/100BASE-FX
IEEE 802.3z Gigabit SX/LX
IEEE 802.3ab Gigabit 1000T
Standards Compliance
IEEE 802.3x flow control and back pressure
IEEE 802.3ad port trunk with LACP
IEEE 802.1D Spanning Tree protocol
IEEE 802.1w Rapid Spanning Tree protocol
17
IEEE 802.1s Multiple Spanning Tree protocol

IEEE 802.1p Class of Service
IEEE 802.1Q VLAN tagging
IEEE 802.1X Port Authentication Network Control
IEEE 802.1ab LLDP
RFC 768 UDP
RFC 793 TFTP
RFC 791 IP
RFC 792 ICMP
RFC 2068 HTTP
RFC 1112 IGMP version 1
RFC 2710 MLD version 1
FRC 3810 MLD version 2
Environment
Temperature: 0 ~ 50 degrees C
Operating
Relative Humidity: 5 ~ 95% (non-condensing)
Temperature: -10 ~ 70 degrees C
Storage
18
GS-5220-44S4C / GS-5220-46S2C4X / GS-5220-48T4X
Product GS-5220-44S4C GS-5220-46S2C4X GS-5220-48T4X
Hardware Specifications
4 10/100/1000BASE-T 2 10/100/1000BASE-T
RJ45 auto-MDI/MDI-X RJ45 auto-MDI/MDI-X 48 10/100/1000BASE-T
Copper Ports
ports, shared with Port-1 to ports, shared with Port-1 to RJ45 auto-MDI/MDI-X ports
Port-4 Port-2
4 100/1000BASE-X SFP
48 100/1000BASE-X SFP 48 100/1000BASE-X SFP interfaces, shared with
interfaces, compatible with interfaces, compatible with Port-45 to Port-48,
SFP/mini-GBIC Slots
100BASE-FX SFP 100BASE-FX SFP compatible with
transceiver transceiver 100BASE-FX SFP
transceiver
4 10GBASE-SR/LR SFP+ interface (Port-49 to Port-52)
SFP+ Slots ---
Compatible with 1000BASE-SX/LX/BX SFP transceiver
Console 1 x RS-232-to-RJ45 serial port (115200, 8, N, 1)
Switch Architecture Store-and-Forward
Switch Fabric 96Gbps 176Gbps 176Gbps
Throughput 71.4 Mpps@64Bytes 130.95Mpps@64Bytes 130.95Mpps@64Bytes
Address Table 16K entries 32K entries 32K entries
Shared Data Buffer 16M bits 32M bits 32M bits

IEEE 802.3x pause frame for full-duplex
Flow Control
Back pressure for half-duplex
Jumbo Frame 10K bytes
< 5 sec: System reboot
Reset Button
> 5 sec: Factory default
Dimensions (W x D x H) 440 x 300 x 44.5 mm, 1U height
Weight 3765g 4346g 4421g
Power Requirements 100~240V AC, 50/60Hz

45 watts / 153 BTU 80 watts / 272.9 BTU 58 watts / 197.9 BTU
Power Consumption
(max.) (max.) (max.)
ESD Protection 2KV DC 6KV DC 6KV DC
Layer 2 Management Functions
Port disable / enable
Port Configuration Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable / enable
Display each port’s speed duplex mode, link status, flow control status,
Port Status
auto-negotiation status, trunk status
TX / RX / Both
Port Mirroring
Many-to-1 monitor
802.1Q tagged based VLAN
Q-in-Q tunneling
Private VLAN Edge (PVE)
MAC-based VLAN
VLAN
Protocol-based VLAN
Voice VLAN
IP Subnet-based VLAN
MVR (Multicast VLAN registration)
19
Up to 255 VLAN groups, out of 4094 VLAN IDs

IEEE 802.3ad LACP / static trunk
GS-5220-44S4C
Link Aggregation 24 groups of 8-port trunk supported
GS-5220-46S2C4X / GS-5220-48T4X
26 groups of 8-port trunk supported
STP, IEEE 802.1D Spanning Tree Protocol
Spanning Tree Protocol RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
MSTP, IEEE 802.1s Multiple Spanning Tree Protocol
Traffic classification based, Strict priority and WRR
8-Level priority for switching
- Port Number
QoS
- 802.1p priority
- 802.1Q VLAN tag
- DSCP/TOS field in IP packet
IGMP (v1/v2/v3) snooping, up to 255 multicast groups
IGMP Snooping
IGMP querier mode support
MLD (v1/v2) snooping, up to 255 multicast groups
MLD Snooping
MLD querier mode support
IP-based ACL / MAC-based ACL
Access Control List
Up to 256 entries
Per port bandwidth control
Bandwidth Control Ingress: 100Kbps~1000Mbps
Egress: 100Kbps~1000Mbps
Layer 3 Functions
IP Interfaces Max. 128 VLAN interfaces
Routing Table Max. 32 routing entries

Routing Protocols
Management
Basic Management Interfaces Console / Telnet / Web browser / SNMP v1, v2c
Secure Management Interfaces SSH, SSL, SNMP v3
RFC 1213 MIB-II RFC 2618 RADIUS Client MIB

RFC 1493 Bridge MIB RFC 2863 IF-MIB
RFC 1643 Ethernet MIB RFC 2933 IGMP-STD-MIB
RFC 2863 Interface MIB RFC 3411 SNMP-Frameworks-MIB
SNMP MIBs RFC 2665 Ether-Like MIB RFC 4292 IP Forward MIB
RFC 2819 RMON MIB (Group 1, 2, 3 RFC 4293 IP MIB
and 9) RFC 4836 MAU-MIB
RFC 2737 Entity MIB IEEE 802.1X PAE
LLDP
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
IEEE 802.3 10BASE-T IEEE 802.1Q VLAN tagging
IEEE 802.3u 100BASE-TX/100BASE-FX IEEE 802.1X Port Authentication Network
IEEE 802.3z Gigabit SX/LX Control
Standards Compliance
IEEE 802.3ab Gigabit 1000T IEEE 802.1ab LLDP
IEEE 802.3ae 10Gb/s Ethernet RFC 768 UDP
IEEE 802.3x flow control and back RFC 793 TFTP
20
pressure RFC 791 IP

IEEE 802.3ad port trunk with LACP RFC 792 ICMP
IEEE 802.1D Spanning Tree protocol RFC 2068 HTTP
IEEE 802.1w Rapid Spanning Tree RFC 1112 IGMP version 1
protocol RFC 2236 IGMP version 2
IEEE 802.1s Multiple Spanning Tree RFC 3376 IGMP version 3
protocol RFC 2710 MLD version 1
IEEE 802.1p Class of service FRC 3810 MLD version 2
Environment
Temperature: 0 ~ 50 degrees C
Operating
Temperature: -10 ~ 70 degrees C
Storage
21
2. INSTALLATION
This section describes the hardware features and installation of the Managed Switch on the desktop or rack mount. For easier
management and control of the Managed Switch, familiarize yourself with its display indicators, and ports. Front panel
illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Managed Switch, please
read this chapter completely.
2.1 Hardware Description
2.1.1 Switch Front Panel
The front panel provides a simple interface monitoring the Managed Switch. Figures 2-1-1 to 2-1-5 show the front panel of the
Managed Switch.
GS-5220-16S8C Front Panel
Figure 2-1-1: Front Panels of GS-5220-16S8C
GS-5220-16S8CR Front Panel
Figure 2-1-2: Front Panels of GS-5220-16S8CR
GS-5220-44S4C Front Panel
Figure 2-1-3: Front Panel of GS-5220-44S4C
GS-5220-46S2C4X Front Panel
Figure 2-1-4: Front Panel of GS-5220-46S2C4X
22
GS-5220-48T4X Front Panel
Figure 2-1-5: Front Panel of GS-5220-48T4X
■ Gigabit TP interface
10/100/1000BASE-T Copper, RJ45 twisted-pair: Up to 100 meters.
■ SFP slot
100/1000BASE-X mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module: From 550 meters to 2km (multi-mode
fiber), up to above 10/20/30/40/50/70/120 kilometers (single-mode fiber).
■ 10 Gigabit SFP+ slot

10GBASE-SR/LR mini-GBIC slot, SFP+ (Small Factor Pluggable Plus) Transceiver module supports from 300 meters
(multi-mode fiber) up to 10 kilometers (single mode fiber)
■ Console Port
The console port is a RJ45 port connector. It is an interface for connecting a terminal directly. Through the console port, it
provides rich diagnostic information including IP address setting, factory reset, port management, link status and system
setting. Users can use the attached DB9 to RJ45 console cable in the package and connect to the console port on the
device. After the connection, users can run any terminal emulation program (Hyper Terminal, ProComm Plus, Telix,
Winterm and so on) to enter the startup screen of the device.
■ Reset button
The front panel of the GS-5220-16S8C(R) / GS-5220-44S4C / GS-5220-46S2C4X comes with a reset button designed for
rebooting the Managed Switch without turning off and on the power. The following is the summary table of reset button
functions:
Reset Button Pressed and Released Function
< 5 sec: System Reboot Reboot the Managed Switch.
Reset the Managed Switch to Factory Default configuration.

The Managed Switch will then reboot and load the default
settings as shown below:
。 Default Username: admin
> 5 sec: Factory Default
。 Default Password: admin
。 Default IP address: 192.168.0.100
。 Subnet mask: 255.255.255.0
。 Default Gateway: 192.168.0.254
The reset button of GS-5220-48T4X is located at the side of the switch.
23
2.1.2 LED Indications
The front panel LEDs indicate instant status of power and system status, fan status, port links / PoE in-use and data activity;
they help monitor and troubleshoot when needed. Figures 2-1-6 to 2-1-10 show the LED indications of the Managed Switch.
GS-5220-16S8C / GS-5220-16S8CR LED Indication
Figure 2-1-6: GS-5220-16S8C LED on Front Panel
Figure 2-1-7: GS-5220-16S8CR LED on Front Panel
 System
LED Color Function
PWR Green Lights to indicate that the Switch has AC power input.
DC Green Lights to indicate that the Switch has DC power input. (GS-5220-16S8CR Only)
 Alert
LED Color Function
FAN Green Lights to indicate fan failure.
Fault Green Lights to indicate ports 1~24 or power input failure.
 Per 10/100/1000Mbps RJ45 port (Port-1 to Port-8)
LED Color Function
1000 Lights: To indicate the port is running in 1000Mbps speed and successfully established.
Green
LNK/ACT Blink: To indicate that the switch is actively sending or receiving data over that port.
10/100 Lights: To indicate the port is running in 10/100Mbps speed and successfully established.
Orange
LNK/ACT Blink: To indicate that the switch is actively sending or receiving data over that port.
24
 Per 100/1000BASE-X SFP Interface (Port-1 to Port-24)
LED Color Function
1000 Lights. To indicate the port is successfully established at 1000Mbps.

Green
LNK/ACT Blink: To indicate that the Switch is actively sending or receiving data over that port.
100 Lights: To indicate the port is successfully established at 100Mbps.

Orange Blink: To indicate that the Switch is actively sending or receiving data over that port.
LNK/ACT
GS-5220-44S4C LED Indication
Figure 2-1-8: Front Panel LEDs of GS-5220-44S4C
 System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
SYS Green Lights to indicate the system is working.
 Alert
LED Color Function
FAN1 Red Lights to indicate that the FAN1 Group failure.
FAN2 Red Lights to indicate that the FAN2 Group failure.
 Per 10/100/1000Mbps RJ45 interfaces (Port-1 to Port-4)
LED Color Function
Lights: Indicates the link through that port is successfully established at 1000Mbps.
Green
Blink: Indicates that the Switch is actively sending or receiving data over that port.
LNK/ACT Lights: Indicates the link through that port is successfully established at 100Mbps.
Orange
OFF Indicates the link through that port is successfully established at 10Mbps.
 Per 100/1000Mbps SFP Combo Interface (Port-1 to Port-48)
LED Color Function
Green
LNK/ACT
Orange
25
GS-5220-46S2C4X LED Indication
Figure 2-1-9: Front Panel LEDs of GS-5220-46S2C4X
 System
LED Color Function
SYS Green Lights up to indicate the system is working.
PWR Green Lights up to indicate that the Switch has power.
FAN1 Red Lights up to indicate fan1 has failed.
FAN2 Red Lights up to indicate fan2 has failed.
 Per 10/100/1000Mbps RJ45 port(Port-1 to Port-2)
LED Color Function
1000 Lights up to indicate the port is running at 1000Mbps speed and successfully established.
Green
LNK/ACT Blinks to indicate that the switch is actively sending or receiving data over that port.
10/100 Lights up to indicate the port is running at 10/100Mbps speed and successfully established.
Orange
LED Color Function
Green
Orange
 Per 10G SFP+ interface(Port-49 to Port-52)
LED Color Function
Lights up to indicate the port is running at 10Gbps speed and successfully established.
10G Green
Blinks to indicate that the switch is actively sending or receiving data over that port.
Lights up to indicate the port is running at 1Gbps speed and successfully established.
1G Green
Blinks to indicate that the switch is actively sending or receiving data over that port.
26
GS-5220-48T4X LED Indication
Figure 2-1-10: Front Panel LEDs of GS-5220-48T4X
 System
LED Color Function
SYS Green Lights up to indicate the system is working.
PWR Green Lights up to indicate that the Switch has power.
 Alert
LED Color Function
FAN1~2 Green Lights up to indicate fan1~2 has failed.
 Per 10/100/1000Mbps RJ45 port
LED Color Function
Green
10/100 Lights up to indicate the port is running at 10/100Mbps speed and successfully established.
Orange
LED Color Function

Lights up to indicate the port is successfully established.
LNK/ACT Green
Blinks to indicate that the Switch is actively sending or receiving data over that port.
 Per 10G SFP+ interface
LED Color Function

Lights up to indicate the port is successfully established.
LNK/ACT Green
Blinks to indicate that the Switch is actively sending or receiving data over that port.
27
2.1.3 Switch Rear Panel
The rear panel of the Managed Switch consists of the AC/DC inlet power socket. Figures 2-1-11 to 2-1-15 show the rear panel of
the Managed Switch.
GS-5220-16S8C / GS-522016S8CR Rear Panel
Figure 2-1-11: Rear Panel of GS-5220-16S8C
Figure 2-1-12: Rear Panel of GS-5220-16S8CR
GS-5220-44S4C Rear Panel
Figure 2-1-13: Rear Panel of GS-5220-44S4C
GS-5220-46S2C4X Rear Panel
Figure 2-1-14: Rear Panel of GS-5220-46S2C4X
GS-5220-48T4X Rear Panel
Figure 2-1-15: Rear Panel of GS-5220-48T4X
■ 10 Gigabit SFP+ slot

10GBASE-SR/LR mini-GBIC slot, SFP+ Transceiver module supports from 300 meters (multi-mode fiber) up to 60
kilometers (single mode Fiber).
■ AC Power Receptacle
For compatibility with electrical voltages in most areas of the world, the Managed Switch’s power supply can automatically
adjust line power in the range of 100-240V AC and 50/60 Hz.
28
Plug the female end of the power cord firmly into the receptable on the rear panel of the Managed Switch and the other end
of the power cord into an electrical outlet and the power will be ready.
The device is a power-required device, which means it will not work till it is powered. If your networks
should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device.
Power Notice: It will prevent you from network data loss or network downtime. In some areas, installing a surge
suppression device may also help to protect your Managed Switch from being damaged by unregulated
surge or current to the Switch or the power adapter.
■ DC Power Connector
The rear panel of the GS-5220-16S8CR has a power switch and a DC power connector, where the latter accepts DC power
input voltage from 36V to 60V DC. Connect the power cable to the Managed Switch at the input terminal block. The size of
the two screws in the terminal block is M3.5.
Figure 2-1-16 Rear Panel of GS-5220-16S8CR
Before connecting the DC power cable to the input terminal block of the GS-5220-16S8CR, make sure
Warning:
that the power switch is in the “OFF” position and the DC power is OFF.
29
2.2 Installing the Switch

This section describes how to install your Managed Switch and make connections to the Managed Switch. Please read the
following topics and perform the procedures in the order being presented. To install your Managed Switch on a desktop or shelf,
simply complete the following steps.
2.2.1 Desktop Installation
To install the Managed Switch on desktop or shelf, please follow these steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom of the Managed Switch.
Step 2: Place the Managed Switch on the desktop or the shelf near an AC power source, as shown in Figure 2-2-1.
Figure 2-2-1: Place the Managed Switch on the Desktop
Step 3: Keep enough ventilation space between the Managed Switch and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1,
Section 4, and specifications.
Step 4: Connect the Managed Switch to network devices.

Connect one end of a standard network cable to the 10/100/1000 RJ45 ports on the front of the Managed Switch.
Connect the other end of the cable to the network devices such as printer server, workstation or router.
Connection to the Managed Switch requires UTP Category 5e network cabling with RJ45 tips. For more
information, please see the Cabling Specification in Appendix A.
Step 5: Supply power to the Managed Switch.

Connect one end of the power cable to the Managed Switch.
Connect the power plug of the power cable to a standard wall outlet.
When the Managed Switch receives power, the Power LED should remain solid Green.
30
2.2.2 Rack Mounting
To install the Managed Switch in a 19-inch standard rack, please follow the instructions described below.
Step 1: Place the Managed Switch on a hard flat surface, with the front panel positioned towards the front side.
Step 2: Attach the rack-mount bracket to each side of the Managed Switch with supplied screws attached to the package.
Figure 2-2-2 shows how to attach brackets to one side of the Managed Switch.
Figure 2-2-2: Attach Brackets to the Managed Switch.
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate the warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the Managed Switch, use suitable screws to securely attach the brackets to the rack,
as shown in Figure 2-2-3.
Figure 2-2-3: Mounting Managed Switch in a Rack
31
Step 6: Proceed with Steps 4 and 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply power to the
Managed Switch.
2.2.3 Installing the SFP/SFP+ Transceiver
The sections describe how to insert an SFP/SFP+ transceiver into an SFP/SFP+ slot. The SFP/SFP+ transceivers are
hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP/SFP+ port without having to power
down the Managed Switch, as the Figure 2-2-4 shows..
Figure 2-2-4: Plug-in the SFP/SFP+ Transceiver
 Approved PLANET SFP/SFP+ Transceivers

PLANET Managed Switch supports both single mode and multi-mode SFP/SFP+ transceiverS. The following list of approved
PLANET SFP/SFP+ transceivers is correct at the time of publication:
Fast Ethernet Transceiver (100BASE-X SFP)
Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
MFB-FX 100 LC Multi Mode 2km 1310nm 0 ~ 60 degrees C
MFB-F20 100 LC Single Mode 20km 1310nm 0 ~ 60 degrees C
MFB-TFX 100 LC Multi Mode 2km 1310nm -40 ~ 75 degrees C
MFB-TF20 100 LC Single Mode 20km 1550nm -40 ~ 75 degrees C
32
Fast Ethernet Transceiver (100BASE-BX, Single Fiber Bi-directional SFP)
Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (TX/RX) Operating Temp.
MFB-FA20 100 WDM(LC) Single Mode 20km 1310nm / 1550nm 0 ~ 60 degrees C
MFB-FB20 100 WDM(LC) Single Mode 20km 1550nm / 1310nm 0 ~ 60 degrees C
MFB-TFA20 100 WDM(LC) Single Mode 20km 1310nm / 1550nm -40 ~ 75 degrees C
MFB-TFB20 100 WDM(LC) Single Mode 20km 1550nm / 1310nm -40 ~ 75 degrees C
MFB-TFA40 100 WDM(LC) Single Mode 40km 1310nm / 1550nm -40 ~ 75 degrees C
MFB-TFB40 100 WDM(LC) Single Mode 40km 1550nm / 1310nm -40 ~ 75 degrees C
Gigabit Ethernet Transceiver (1000BASE-X SFP)
Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
MGB-GT 1000 Copper -- 100m -- 0 ~ 60 degrees C
MGB-SX 1000 LC Multi Mode 550m 850nm 0 ~ 60 degrees C
MGB-SX2 1000 LC Multi Mode 2km 1310nm 0 ~ 60 degrees C
MGB-LX 1000 LC Single Mode 10km 1310nm 0 ~ 60 degrees C
MGB-L30 1000 LC Single Mode 30km 1310nm 0 ~ 60 degrees C
MGB-TSX 1000 LC Multi Mode 550m 850nm -40 ~ 75 degrees C
MGB-TLX 1000 LC Single Mode 10km 1310nm -40 ~ 75 degrees C
MGB-TL30 1000 LC Single Mode 30km 1310nm -40 ~ 75 degrees C
MGB-TL70 1000 LC Single Mode 70km 1550nm -40 ~ 75 degrees C
Gigabit Ethernet Transceiver (1000BASE-BX, Single Fiber Bi-directional SFP)
Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (TX/RX) Operating Temp.
MGB-LA10 1000 WDM(LC) Single Mode 10km 1310nm / 1550nm 0 ~ 60 degrees C
MGB-LB10 1000 WDM(LC) Single Mode 10km 1550nm / 1310nm 0 ~ 60 degrees C
MGB-TLA10 1000 WDM(LC) Single Mode 10km 1310nm / 1550nm -40 ~ 75 degrees C
MGB-TLB10 1000 WDM(LC) Single Mode 10km 1550nm / 1310nm -40 ~ 75 degrees C
33
10Gbps SFP+ (10G Ethernet/10GBASE)

Connector
Model Speed (Mbps) Fiber Mode Distance Wavelength (nm) Operating Temp.
Interface
MTB-SR 10G LC Multi Mode Up to 300m 850nm 0 ~ 60 degrees C
MTB-LR 10G LC Single Mode 10km 1310nm 0 ~ 60 degrees C
10Gbps SFP+ (10GBASE-BX, Single Fiber Bi-directional SFP)

Connector
Model Speed (Mbps) Fiber Mode Distance Wavelength (TX) Wavelength (RX) Operating Temp.
Interface
MTB-LA20 10G WDM(LC) Single Mode 20km 1270nm 1330nm 0 ~ 60 degrees C
MTB-LB20 10G WDM(LC) Single Mode 20km 1330nm 1270nm 0 ~ 60 degrees C
It is recommended to use PLANET SFP / SFP+ on the Managed Switch. If you insert an SFP / SFP+
transceiver that is not supported, the Managed Switch will not recognize it.
1. Before we connect the GS-5220 series to the other network device, we have to make sure both sides of the SFP
transceivers are with the same media type, for example: 1000BASE-SX to 1000BASE-SX, 1000Bas-LX to 1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
 To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male
duplex LC connector type.
 To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male
duplex LC connector type.
 Connect the Fiber Cable

1. Insert the duplex LC connector into the SFP / SFP+ transceiver.
2. Connect the other end of the cable to a device with SFP / SFP+ transceiver installed.
3. Check the LNK/ACT LED of the SFP / SFP+ slot on the front of the Managed Switch. Ensure that the SFP / SFP+
transceiver is operating correctly.
4. Check the Link mode of the SFP / SFP+ port if the link fails. To function with some fiber-NICs or Media Converters, user
has to set the port Link mode to “10G Force”, “1000M Force” or “100M Force”.
 Remove the Transceiver Module

1. Make sure there is no network activity anymore.
2. Remove the Fiber-Optic Cable gently.
34
3. Lift up the lever of the MGB module and turn it to a horizontal position.
4. Pull out the module gently through the lever.
Figure 2-2-5: How to Pull Out the SFP / SFP+ Transceiver
Never pull out the module without lifting up the lever of the module and turning it to a horizontal
position. Directly pulling out the module could damage the module and the SFP / SFP+ module
slot of the Managed Switch.
35
3. SWITCH MANAGEMENT
This chapter explains the methods that you can use to configure management access to the Managed Switch. It describes the
types of management applications and the communication and management protocols that deliver data between your
management device (workstation or personal computer) and the system. It also contains information about port connection
options.
This chapter covers the following topics:
 Requirements
 Management Access Overview
 Administration Console Access
 Web Management Access
 SNMP Access
 Standards, Protocols, and Related Reading
3.1 Requirements
 Workstations running Windows 2000/XP, 2003, Vista/7/8, 2008, MAC OS9 or later, or Linux, UNIX , or other
platforms compatible with TCP/IP protocols.
 Workstation is installed with Ethernet NIC (Network Interface Card)
 Serial Port connect (Terminal)
 The above PC with COM Port (DB9 / RS-232) or USB-to-RS-232 converter

 Ethernet Port connect
 Network cables - Use standard network (UTP) cables with RJ45 connectors.
 The above workstation is installed with Web Browser and JAVA runtime environment plug-in
It is recommended to use Internet Explore 7.0 or above to access Managed Switch.
36
3.2 Management Access Overview

The Managed Switch gives you the flexibility to access and manage it using any or all of the following methods:
 An administration console
 Web browser interface
 An external SNMP-based network management application
The administration console and Web browser interface support are embedded in the Managed Switch software and are
available for immediate use. Each of these management methods has their own advantages. Table 3-1 compares the three
management methods.
Method Advantages Disadvantages
Console  No IP address or subnet needed  Must be near the switch or use dial-up
 Text-based connection
 Telnet functionality and HyperTerminal  Not convenient for remote users

built into Windows  Modem connection may prove to be unreliable
95/98/NT/2000/ME/XP operating or slow
systems
 Secure
Web Browser  Ideal for configuring the switch remotely  Security can be compromised (hackers need
 Compatible with all popular browsers only know the IP address and subnet mask)
 Can be accessed from any location  May encounter lag times on poor connections
 Most visually appealing
SNMP Agent  Communicates with switch functions at  Requires SNMP manager software
the MIB level  Least visually appealing of all three methods
 Based on open standards  Some settings require calculations

 Security can be compromised (hackers need
only know the community name)
Table 3-1 Comparison of Management Methods
37
3.3 Administration Console

The administration console is an internal, character-oriented, and command line user interface for performing system
administration such as displaying statistics or changing option settings. Using this method, you can view the administration
console from a terminal, personal computer, Apple Macintosh, or workstation connected to the Managed Switch's console
(serial) port.
Figure 3-1-1: Console Management
Direct Access
Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a
terminal-emulation program (such as HyperTerminal) to the Managed Switch console (serial) port. When using this
management method, a straight DB9 RS-232 cable is required to connect the switch to the PC. After making this connection,
configure the terminal-emulation program to use the following parameters:
The default parameters are:
 115200 bps
 8 data bits
 No parity
 1 stop bit
Figure 3-1-2: Terminal Parameter Settings
38
You can change these settings, if desired, after you log on. This management method is often preferred because you can
remain connected and monitor the system during system reboots. Also, certain error messages are sent to the serial port,
regardless of the interface through which the associated action was initiated. A Macintosh or PC attachment can use any
terminal-emulation program for connecting to the terminal serial port. A workstation attachment under UNIX can use an emulator
such as TIP.
3.4 Web Management

The Managed Switch offers management features that allow users to manage the Managed Switch from anywhere on the
network through a standard browser such as Microsoft Internet Explorer. After you set up your IP address for the switch, you can
access the Managed Switch's Web interface applications directly in your Web browser by entering the IP address of the
Managed Switch.
Figure 3-1-3: Web Management
You can then use your Web browser to list and manage the Managed Switch configuration parameters from one central location,
just as if you were directly connected to the Managed Switch's console port. Web Management requires either Microsoft
Internet Explorer 7.0 or later, Safari or Mozilla Firefox 1.5 or later.
Figure 3-1-4: Web Main Screen of Managed Switch
39
3.5 SNMP-based Network Management

You can use an external SNMP-based application to configure and manage the Managed Switch, such as SNMP Network
Manager, HP Openview Network Node Management (NNM) or What’s Up Gold. This management method requires the SNMP
agent on the switch and the SNMP Network Management Station to use the same community string. This management
method, in fact, uses two community strings: the get community string and the set community string. If the SNMP Net-work
management Station only knows the set community string, it can read and write to the MIBs. However, if it only knows the get
community string, it can only read MIBs. The default getting and setting community strings for the Managed Switch is public.
Figure 3-1-5: SNMP Management
3.6 PLANET Smart Discovery Utility

For easily listing the Managed Switch in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual
CD-ROM is an ideal solution. The following installation instructions are to guide you to running the Planet Smart Discovery
Utility.
1. Deposit the Planet Smart Discovery Utility in administrator PC.
2. Run this utility as the following screen appears.
Figure 3-1-6: Planet Smart Discovery Utility Screen
40
If there are two LAN cards or above in the same administrator PC, choose a different LAN card
by using the “Select Adapter” tool.
3. Press “Refresh” button for the currently connected devices in the discovery list as the screen shows below:
Figure 3-1-7: Planet Smart Discovery Utility Screen
1. This utility shows all necessary information from the devices, such as MAC Address, Device Name, firmware version, and
Device IP Subnet address. It can also assign new password, IP Subnet address and description for the devices.
2. After setup is completed, press “Update Device”, “Update Multi” or “Update All” button to take effect. The meaning of
the 3 buttons above are shown as below:
 Update Device: use current setting on one single device.
 Update Multi: use current setting on choose multi-devices.
 Update All: use current setting on whole devices in the list.
The same functions mentioned above also can be found in “Option” tools bar.
3. To click the “Control Packet Force Broadcast” function, it can allow assign new setting value to the Web Smart Switch
under a different IP subnet address.
4. Press “Connect to Device” button and the Web login screen appears in Figure 3-1-4.
5. Press “Exit” button to shut down the Planet Smart Discovery Utility.
41
4. WEB CONFIGURATION
This section introduces the configuration and functions of the Web-based management from Managed Switch.
About Web-based Management

The Managed Switch offers management features that allow users to manage the Managed Switch from anywhere on the
network through a standard browser such as Microsoft Internet Explorer.
The Web-based Management supports Internet Explorer 7.0. It is based on Java Applets with an aim to reduce network
bandwidth consumption, enhance access speed and present an easy viewing screen.
By default, IE7.0 or later version does not allow Java Applets to open sockets. The user has to explicitly
modify the browser setting to enable Java Applets to use network ports.
The Managed Switch can be configured through an Ethernet connection, making sure the manager PC must be set on the same
IP subnet address with the Managed Switch.
For example, the default IP address of the Managed Switch is 192.168.0.100, then the manager PC should be set at
192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
If you have changed the default IP address of the Managed Switch to 192.168.1.1 with subnet mask 255.255.255.0 via console,
then the manager PC should be set at 192.168.1.x (where x is a number between 2 and 254) to do the relative configuration on
manager PC.
Figure 4-1-1: Web Management
 Logging on the Managed Switch

1. Use Internet Explorer 7.0 or above Web browser. Enter the factory-default IP address to access the Web interface. The
factory-default IP Address is shown as follows:
http://192.168.0.100
42
2. When the following login screen appears, please enter the default username "admin" with password “admin” (or the
username/password you have changed via console) to login the main screen of Managed Switch. The login screen in
Figure 4-1-2 appears.
Figure 4-1-2: Login Screen
Default User name: admin
Default Password: admin
After entering the username and password, the main screen appears as shown in Figure 4-1-3.
Figure 4-1-3: Web Main Page
43
Now, you can use the Web management interface to continue the switch management or manage the Managed Switch by Web
interface. The Switch Menu on the left of the web Page lets you access all the commands and statistics the Managed Switch
provides.
1. It is recommended to use Internet Explore 7.0 or above to access Managed Switch.

2. The changed IP address takes effect immediately after clicking on the Save button. You need to
use the new IP address to access the Web interface.
3. For security reason, please change and memorize the new password after this first setup.
4. Only accept command in lowercase letter under web interface.
4.1 Main Web Page

The Managed Switch provides a Web-based browser interface for configuring and managing it. This interface allows you to
access the Managed Switch using the Web browser of your choice. This chapter describes how to use the Managed Switch’s
Web browser interface to configure and manage it.
Main Functions Menu

Copper Port Link Status SFP/SFP+ Port Link
Figure 4-1-4: Web Main Page

Help Button Main Screen
Panel Display
The web agent displays an image of the Managed Switch’s ports. The Mode can be set to display different information for the
ports, including Link up or Link down. Clicking on the image of a port opens the Port Statistics Page.
The port status are illustrated as follows:
State Disabled Down Link
RJ45 Ports
SFP Ports
44
Main Menu
Using the onboard web agent, you can define system parameters, manage and control the Managed Switch, and all its ports, or
monitor network conditions. Via the Web-Management, the administrator can set up the Managed Switch by selecting the
functions those listed in the Main Function. The screen in Figure 4-1-5 appears.
Figure 4-1-5: Managed Switch Main Functions Menu
45
4.2 System
Use the System menu items to display and configure basic administrative details of the Managed Switch. Under the System, the
following topics are provided to configure and view the system information. This section has the following items:
■ System Information The Managed Switch system information is provided here.
■ IP Configuration Configures the Managed Switch-managed IPv4/IPv6 interface and IP routes

on this Page.
■ IP Status This page displays the status of the IP protocol layer. The status is defined
by the IP interfaces, the IP routes and the neighbour cache (ARP cache)
status.
■ Users Configuration This Page provides an overview of the current users. Currently the only way
to login as another user on the web server is to close and reopen the
browser.
■ Privilege Levels This Page provides an overview of the privilege levels.
■ NTP Configuration Configure NTP server on this Page.
■ Time Configuration Configure time parameter on this Page.
■ UPnP Configure UPnP on this Page.
■ DHCP Relay Configure DHCP Relay on this Page.
■ DHCP Relay Statistics This Page provides statistics for DHCP relay.
■ CPU Load This Page displays the CPU load, using an SVG graph.
■ System Log The Managed Switch system log information is provided here.
■ Detailed Log The Managed Switch system detailed log information is provided here.
■ Remote Syslog Configure remote syslog on this Page.
■ SMTP Configuration Configuration SMTP parameters on this Page.
■ Web Firmware Upgrade This Page facilitates an update of the firmware controlling the Managed
Switch.
■ TFTP Firmware Upgrade Upgrade the firmware via TFTP server
■ Save Startup Config This copies running-config to startup-config, thereby ensuring that the
currently active configuration will be used at the next reboot.
■ Configuration Download You can download the files on the switch.
■ Configuration Upload You can upload the files to the switch.
■ Configuration Activate You can activate the configuration file present on the switch.
■ Configuration Delete You can delete the writable files which stored in flash.
■ Image Select Configuration active or alternate firmware on this Page.
■ Factory Default You can reset the configuration of the Managed Switch on this Page. Only
the IP configuration is retained.
■ System Reboot You can restart the Managed Switch on this Page. After restarting, the
Managed Switch will boot normally.
46
4.2.1 System Information
The System Infomation Page provides information for the current device information. System Information Page helps a switch
administrator to identify the hardware MAC address, software version and system uptime. The screen in Figure 4-2-1 appears.
Figure 4-2-1: System Information Page Screenshot
The Page includes the following fields:
Object Description
 Contact The system contact configured in SNMP | System Information | System Contact.
 Name The system name configured in SNMP | System Information | System Name.
 Location The system location configured in SNMP | System Information | System Location.
 MAC Address The MAC Address of this Managed Switch.
 Temperature Indicates chipset temperature.
 System Date The current (GMT) system time and date. The system time is obtained through the
configured NTP Server, if any.
 System Uptime The period of time the device has been operational.
 Software Version The software version of the Managed Switch.
 Software Date The date when the Managed Switch software was produced.
Buttons
Auto-refresh : Check this box to refresh the Page automatically. Automatic refresh occurs every 3 seconds.
: Click to refresh the Page; any changes made locally will be undone.
47
4.2.2 IP Configuration
The IP Configuration includes the IP Configuration, IP Interface and IP Routes. The configured column is used to view or
change the IP configuration. The maximum number of interfaces supported is 128 and the maximum number of routes is 32.
The screen in Figure 4-2-2 appears.
Figure 4-2-2: IP Configuration Page Screenshot
The current column is used to show the active IP configuration.
Object Description
 IP Configurations Mode Configure whether the IP stack should act as a Host or a Router. In
Host mode, IP traffic between interfaces will not be routed. In Router
mode traffic is routed between all interfaces.
DNS Server This setting controls the DNS name resolution done by the switch. The
following modes are supported:
 From any DHCP interfaces

The first DNS server offered from a DHCP lease to a DHCP-enabled
interface will be used.
 No DNS server
No DNS server will be used.
 Configured
Explicitly provide the IP address of the DNS Server in dotted decimal
notation.
 From this DHCP interface
48
Specify from which DHCP-enabled interface a provided DNS server
should be preferred.
DNS Proxy When DNS proxy is enabled, system will relay DNS requests to the
currently configured DNS server, and reply as a DNS resolver to the client
devices on the network.
 IP Address Delete Select this option to delete an existing IP interface.
VLAN The VLAN associated with the IP interface. Only ports in this VLAN will be
able to access the IP interface. This field is only available for input when
creating an new interface.
IPv4 Enabled Enable the DHCP client by checking this box.

DHCP Fallback The number of seconds for trying to obtain a DHCP lease.
Current Lease For DHCP interfaces with an active lease, this column show the current
interface address, as provided by the DHCP server.
IPv4 Address Provide the IP address of this Managed Switch in dotted decimal notation.
Mask Length The IPv4 network mask, in number of bits (prefix length). Valid values are
between 0 and 30 bits for a IPv4 address.
IPv6 Address Provide the IP address of this Managed Switch. A IPv6 address is in
128-bit records represented as eight fields of up to four hexadecimal
digits with a colon separating each field (:).
Mask Length The IPv6 network mask, in number of bits (prefix length). Valid values are
between 1 and 128 bits for a IPv6 address.
 IP Routes Delete Select this option to delete an existing IP route.
Network The destination IP network or host address of this route. Valid format is
dotted decimal notationor a valid IPv6 notation. A default route can use
the value 0.0.0.0or IPv6 :: notation.
Mask Length The destination IP network or host mask, in number of bits (prefix length).
Gateway The IP address of the IP gateway. Valid format is dotted decimal notation
or a valid IPv6 notation. Gateway and Network must be of the same type.
Next Hop VLAN The VLAN ID (VID) of the specific IPv6 interface associated with the
gateway.
Buttons
: Click to add a new IP interface. A maximum of 128 interfaces is supported.
: Click to add a new IP route. A maximum of 32 routes is supported.
: Click to apply changes.
: Click to undo any changes made locally and revert to previously saved values.
49
4.2.3 IP Status
IP Status displays the status of the IP protocol layer. The status is defined by the IP interfaces, the IP routes and the neighbour
cache (ARP cache) status. The screen in Figure 4-2-3 appears.
Figure 4-2-3: IP Status Page Screenshot
Object Description
 IP Interfaces Interface The name of the interface.
Type The address type of the entry. This may be LINK or IPv4.
Address The current address of the interface (of the given type).
Status The status flags of the interface (and/or address).
 IP Routes Network The destination IP network or host address of this route.
Gateway The gateway address of this route.
Status The status flags of the route.
 Neighbor Cache IP Address The IP address of the entry.
Link Address The Link (MAC) address for which a binding to the IP address given exist.
Buttons
: Click to refresh the Page.
50
4.2.4 Users Configuration
This Page provides an overview of the current users. Currently the only way to login as another user on the web server is to
close and reopen the browser. After setup is completed, press “Apply” button to take effect. Please login web interface with
new user name and password, the screen in Figure 4-2-4 appears.
Figure 4-2-4: Users Configuration Page Screenshot
Object Description
 User Name The name identifying the user. This is also a link to Add/Edit User.
 Privilege Level The privilege level of the user.
The allowed range is 1 to 15. If the privilege level value is 15, it can access all
groups, i.e. that is granted the fully control of the device. But others value need to
refer to each group privilege level. User's privilege should be same or greater
than the group privilege level to have the access of that group.
By default setting, most groups privilege level 5 has the read-only access and
privilege level 10 has the read-write access. And the system maintenance
(software upload, factory defaults and etc.) need user privilege level 15.
Generally, the privilege level 15 can be used for an administrator account,
privilege level 10 for a standard user account and privilege level 5 for a guest
account.
Buttons
: Click to add a new user.
Add / Edit User

This Page configures a user – add, edit or delete user.
51
Figure 4-2-5: Add / Edit User Configuration Page Screenshot
Object Description
 Username A string identifying the user name that this entry should belong to. The allowed
string length is 1 to 31. The valid user name is a combination of letters, numbers
and underscores.
 Password The password of the user. The allowed string length is 1 to 31.
 Password (again) Please enter the user’s new password here again to confirm.
 Privilege Level The privilege level of the user.
The allowed range is 1 to 15. If the privilege level value is 15, it can access all
groups, i.e. that is granted the fully control of the device. But others value need to
refer to each group privilege level. User's privilege should be same or greater
than the group privilege level to have the access of that group.
By default setting, most groups privilege level 5 has the read-only access and
privilege level 10 has the read-write access. And the system maintenance
(software upload, factory defaults and etc.) need user privilege level 15.
Generally, the privilege level 15 can be used for an administrator account,
privilege level 10 for a standard user account and privilege level 5 for a guest
account.
Buttons
: Click to undo any changes made locally and return to the Users.
: Delete the current user. This button is not available for new configurations (Add new user)
52
Once the new user is added, the new user entry shown in the Users Configuration Page.
Figure 4-2-6: User Configuration Page Screenshot
If you forget the new password after changing the default password, please press the “Reset”
button on the front panel of the Managed Switch for over 10 seconds and then release it. The
current setting including VLAN will be lost and the Managed Switch will restore to the default
mode.
53
4.2.5 Privilege Levels
This Page provides an overview of the privilege levels. After setup is completed, please press “Apply” button to take effect.
Please login web interface with new user name and password and the screen in Figure 4-2-7 appears.
Figure 4-2-7: Privilege Levels Configuration Page Screenshot
Object Description
 Group Name The name identifying the privilege group. In most cases, a privilege level group
consists of a single module (e.g. LACP, RSTP or QoS), but a few of them contain
more than one. The following description defines these privilege level groups in
details:
 System: Contact, Name, Location, Timezone, Log.
54
 Security: Authentication, System Access Management, Port (contains Dot1x

port, MAC based and the MAC Address Limit), ACL, HTTPS, SSH, ARP
Inspection and IP source guard.
 IP: Everything except 'ping'.

 Port: Everything except 'VeriPHY'.
 Diagnostics: 'ping' and 'VeriPHY'.
 Maintenance: CLI- System Reboot, System Restore Default, System
Password, Configuration Save, Configuration Load and Firmware Load.
Web- Users, Privilege Levels and everything in Maintenance.
 Debug: Only present in CLI.

 Privilege Level Every privilege level group has an authorization level for the following sub
groups:
 Configuration read-only
 Configuration/execute read-write
 Status/statistics read-only
 Status/statistics read-write (e.g. for clearing of statistics).
Buttons
4.2.6 NTP Configuration
Configure NTP on this Page. NTP is an acronym for Network Time Protocol, a network protocol for synchronizing the clocks of
computer systems. NTP uses UDP (data grams) as transport layer. You can specify NTP Servers. The NTP Configuration
screen in Figure 4-2-8 appears.
Figure 4-2-8: NTP Configuration Page Screenshot
55
Object Description
 Mode Indicates the NTP mode operation. Possible modes are:
 Enabled: Enable NTP mode operation. When enable NTP mode operation,
the agent forward and to transfer NTP messages between the clients and the
server when they are not on the same subnet domain.
 Disabled: Disable NTP mode operation.

 Server # Provide the NTP IPv4 or IPv6 address of this switch. IPv6 address is in 128-bit
records represented as eight fields of up to four hexadecimal digits with a colon
separates each field (:).
For example, 'fe80::215:c5ff:fe03:4dc7'. The symbol '::' is a special syntax that
can be used as a shorthand way of representing multiple 16-bit groups of
contiguous zeros; but it can only appear once. It also used a following legally
IPv4 address. For example, '::192.1.2.34'.
Buttons
4.2.7 Time Configuration
Configure Time Zone on this Page. A Time Zone is a region that has a uniform standard time for legal, commercial, and social
purposes. It is convenient for areas in close commercial or other communication to keep the same time, so time zones tend to
follow the boundaries of countries and their subdivisions. The Time Zone Configuration screen in Figure 4-2-9 appears
56
Figure 4-2-9: Time Configuration Page Screenshot
Object Description
 Time Zone Lists various Time Zones world wide. Select appropriate Time Zone from the drop
down and click Save to set.
 Acronym User can set the acronym of the time zone. This is a User configurable acronym
to identify the time zone. ( Range : Up to 16 characters )
 Daylight Saving Time This is used to set the clock forward or backward according to the configurations
set below for a defined Daylight Saving Time duration. Select 'Disable' to disable
the Daylight Saving Time configuration. Select 'Recurring' and configure the
Daylight Saving Time duration to repeat the configuration every year. Select
'Non-Recurring' and configure the Daylight Saving Time duration for single time
configuration. ( Default : Disabled ).
 Start Time Settings  Week - Select the starting week number.
 Day - Select the starting day.
57
 Month - Select the starting month.
 Hours - Select the starting hour.
 Minutes - Select the starting minute.
 End Time Settings  Week - Select the ending week number.
 Day - Select the ending day.
 Month - Select the ending month.
 Hours - Select the ending hour.
 Minutes - Select the ending minute
 Offset Settings Enter the number of minutes to add during Daylight Saving Time. ( Range: 1 to
1440 )
Buttons
4.2.8 UPnP
Configure UPnP on this Page. UPnP is an acronym for Universal Plug and Play. The goals of UPnP are to allow devices to
connect seamlessly and to simplify the implementation of networks in the home (data sharing, communications, and
entertainment) and in corporate environments for simplified installation of computer components. The UPnP Configuration
Figure 4-2-10: UPnP Configuration Page Screenshot
Object Description
 Mode Indicates the UPnP operation mode. Possible modes are:
 Enabled: Enable UPnP mode operation.

 Disabled: Disable UPnP mode operation.
58
When the mode is enabled, two ACEs are added automatically to trap UPnP
related packets to CPU. The ACEs are automatically removed when the mode is
disabled.
 TTL The TTL value is used by UPnP to send SSDP advertisement messages.
Valid values are in the range of 1 to 255.
 Advertising Duration The duration, carried in SSDP packets, is used to inform a control point or control
points how often it or they should receive a SSDP advertisement message from
this switch. If a control point does not receive any message within the duration, it
will think that the switch no longer exists. Due to the unreliable nature of UDP, in
the standard it is recommended that such refreshing of advertisements to be
done at less than one-half of the advertising duration. In the implementation, the
switch sends SSDP messages periodically at the interval one-half of the
advertising duration minus 30 seconds. Valid values are in the range 100 to
86400.
Buttons
: Click to apply changes
Figure 4-2-11: UPnP devices show on Windows My Network Place
59
4.2.9 DHCP Relay
Configure DHCP Relay on this Page. DHCP Relay is used to forward and to transfer DHCP messages between the clients and
the server when they are not on the same subnet domain.
The DHCP option 82 enables a DHCP relay agent to insert specific information into a DHCP request packets when forwarding
client DHCP packets to a DHCP server and remove the specific information from a DHCP reply packets when forwarding server
DHCP packets to a DHCP client. The DHCP server can use this information to implement IP address or other assignment
policies. Specifically the option works by setting two sub-options:
 Circuit ID (option 1)
 Remote ID (option2).
The Circuit ID sub-option is supposed to include information specific to which circuit the request came in on.
The Remote ID sub-option was designed to carry information relating to the remote host end of the circuit.
The definition of Circuit ID in the switch is 4 bytes in length and the format is "vlan_id" "module_id" "port_no". The parameter of
"vlan_id" is the first two bytes representing the VLAN ID. The parameter of "module_id" is the third byte for the module ID. The
parameter of "port_no" is the fourth byte and it means the port number.
The Remote ID is 6 bytes in length, and the value equals the DHCP relay agent’s MAC address. The DHCP Relay Configuration
Figure 4-2-12 DHCP Relay Configuration Page Screenshot
Object Description
 Relay Mode Indicates the DHCP relay mode operation. Possible modes are:
 Enabled: Enable DHCP relay mode operation. When enabling DHCP relay
mode operation, the agent forwards and transfers DHCP messages between
the clients and the server when they are not on the same subnet domain.
And the DHCP broadcast message won't flood for security considered.
 Disabled: Disable DHCP relay mode operation.

 Relay Server Indicates the DHCP relay server IP address. A DHCP relay agent is used to
forward and transfer DHCP messages between the clients and the server when
they are not on the same subnet domain.
60
 Relay Information Indicates the DHCP relay information mode option operation. Possible modes
Mode are:
 Enabled: Enable DHCP relay information mode operation. When enabling

DHCP relay information mode operation, the agent inserts specific
information (option82) into a DHCP message when forwarding to DHCP
server and removing it from a DHCP message when transferring to DHCP
client. It only works under DHCP relay operation mode enabled.
 Disabled: Disable DHCP relay information mode operation.

 Relay Information Indicates the DHCP relay information option policy. When enabling DHCP relay
Policy information mode operation, if agent receives a DHCP message that already
contains relay agent information. It will enforce the policy. And it only works under
DHCP relay information operation mode enabled. Possible policies are:
 Replace: Replace the original relay information when receiving a DHCP

message that already contains it.
 Keep: Keep the original relay information when receiving a DHCP message
that already contains it.
 Drop: Drop the package when receiving a DHCP message that already
contains relay information.
Buttons
4.2.10 DHCP Relay Statistics
This Page provides statistics for DHCP relay. The DHCP Relay Statistics screen in Figure 4-2-13 appears.
Figure 4-2-13: DHCP Relay Statistics Page Screenshot
61
Server Statistics
Object Description
 Transmit to Server The packets number that relayed from client to server.
 Transmit Error The packets number that errors sending packets to clients.
 Receive from Server The packets number that received packets from server.
 Receive Missing Agent The packets number that received packets without agent information options.
Option
 Receive Missing The packets number that received packets which the Circuit ID option was
Circuit ID missing.
 Receive Missing The packets number that received packets which Remote ID option was missing.
Remote ID
 Receive Bad Circuit ID The packets number that the Circuit ID option did not match known circuit ID.
Receive Bad Remote ID The packets number that the Remote ID option did not match known Remote ID.
Client Statistics
Object Description
 Transmit to Client The packets number that relayed packets from server to client.
 Transmit Error The packets number that erroneously sent packets to servers.
 Receive from Client The packets number that received packets from server.
 Receive Agent Option The packets number that received packets with relay agent information option.
 Replace Agent Option The packets number that replaced received packets with relay agent information
option.
 Keep Agent Option The packets number that kept received packets with relay agent information
option.
 Drop Agent Option The packets number that dropped received packets with relay agent information
option.
Buttons
: Click to refresh the Page immediately.
: Clears all statistics.
62
4.2.11 CPU Load
This Page displays the CPU load, using a SVG graph. The load is measured as average over the last 100ms, 1sec and 10
seconds intervals. The last 120 samles are graphed, and the last numbers are displayed as text as well. In order to display the
SVG graph, your browser must support the SVG format. Consult the SVG Wiki for more information on browser support.
Specifically, at the time of writing, Microsoft Internet Explorer will need to have a plugin installed to support SVG. The CPU Load
Figure 4-2-14: CPU Load Page Screenshot
Buttons
If your browser cannot display anything on this Page, please download Adobe SVG tool and
install it in your computer.
63
4.2.12 System Log
The Managed Switch system log information is provided here. The System Log screen in Figure 4-2-15 appears.
Figure 4-2-15: System Log Page Screenshot
Object Description
 ID The ID (>= 1) of the system log entry.
 Level The level of the system log entry. The following level types are supported:
 Info: Information level of the system log.

 Warning: Warning level of the system log.
 Error: Error level of the system log.
 All: All levels.
 Clear Level To clear the system log entry level. The following level types are supported:
 Info: Information level of the system log.

 Warning: Warning level of the system log.
 Error: Error level of the system log.
 All: All levels.
 Time The time of the system log entry.
 Message The message of the system log entry.
Buttons
: Updates the system log entries, starting from the current entry ID.
: Flushes the selected log entries.
: Hides the selected log entries.
: Downloads the selected log entries.
64
: Updates the system log entries, starting from the first available entry ID.
: Updates the system log entries, ending at the last entry currently displayed.
: Updates the system log entries, starting from the last entry currently displayed.
: Updates the system log entries, ending at the last available entry ID.
4.2.13 Detailed Log
The Managed Switch system detailed log information is provided here. The Detailed Log screen in Figure 4-2-16 appears.
Figure 4-2-15: Detailed Log Page Screenshot
Object Description
 ID The ID (>= 1) of the system log entry.
 Message The message of the system log entry.
Buttons
: Download the system log entry to the current entry ID.
: Updates the system log entry to the current entry ID.
: Updates the system log entry to the first available entry ID.
: Updates the system log entry to the previous available entry ID.
: Updates the system log entry to the next available entry ID.
: Updates the system log entry to the last available entry ID.
: Print the system log entry to the current entry ID.
65
4.2.14 Remote Syslog
Configure remote syslog on this Page. The Remote Syslog screen in Figure 4-2-17 appears.
Figure 4-2-17: Remote Syslog Page Screenshot
Object Description
 Mode Indicates the server mode operation. When the mode operation is enabled, the
syslog message will send out to syslog server. The syslog protocol is based on
UDP communication and received on UDP port 514 and the syslog server will not
send acknowledgments back sender since UDP is a connectionless protocol and
it does not provide acknowledgments. The syslog packet will always send out
even if the syslog server does not exist. Possible modes are:
 Enabled: Enable remote syslog mode operation.

 Disabled: Disable remote syslog mode operation.
 Syslog Server IP Indicates the IPv4 host address of syslog server. If the switch provides DNS
feature, it also can be a host name.
 Syslog Level Indicates what kind of message will send to syslog server. Possible modes are:
 Info: Send information, warnings and errors.

 Warning: Send warnings and errors.
 Error: Send errors.
Buttons
66
4.2.15 SMTP Configuration
This Page facilitates an SMTP Configuration on the switch. The SMTP Configure screen in Figure 4-2-18 appears.
Figure 4-2-18: SMTP Configuration Page Screenshot
Object Description
 SMTP Mode Controls whether SMTP is enabled on this switch.
 SMTP Server Type the SMTP server name or the IP address of the SMTP server.
 SMTP Port Set port number of SMTP service.
 SMTP Authentication Controls whether SMTP authentication is enabled If authentication is required
when an e-mail is sent.
 Authentication User Type the user name for the SMTP server if Authentication is Enable.
Name
 Authentication Type the password for the SMTP server if Authentication is Enable.
Password
 E-mail From Type the sender’s E-mail address. This address is used for reply e-mails.
 E-mail Subject Type the subject/title of the e-mail.
 E-mail 1 To Type the receiver’s e-mail address.

 E-mail 2 To
Buttons
: Send a test mail to mail server to check this account is available or not.
: Click to save changes.
67
4.2.16 Web Firmware Upgrade
This Page facilitates an update of the firmware controlling the switch. The Web Firmware Upgrade screen in Figure 4-2-19
appears.
Figure 4-2-19: Web Firmware Upgrade Page Screenshot
To open Firmware Upgrade screen, perform the following:
1. Click System -> Web Firmware Upgrade.
2. The Firmware Upgrade screen is displayed as in Figure 4-2-19.
3. Click the “ “button of the Main Page, the system would pop up the file selection menu to choose firmware.
4. Select on the firmware then click “ ”, the Software Upload Progress would show the file with upload status.
5. Once the software is loaded to the system successfully, the following screen appears. The system will load the new
software after reboot.
Figure 4-2-20: Software Successfully Loaded Notice Screen
DO NOT Power OFF the Managed Switch until the update progress is complete.
Do not quit the Firmware Upgrade Page without pressing the “OK” button after the image is
loaded. Or the system won’t apply the new firmware. User has to repeat the firmware
upgrade processes.
68
4.2.17 TFTP Firmware Upgrade
The Firmware Upgrade Page provides the functions to allow a user to update the Managed Switch firmware from the TFTP
server in the network. Before updating, make sure you have your TFTP server ready and the firmware image is on the TFTP
server. The TFTP Firmware Upgrade screen in Figure 4-2-21 appears.
Figure 4-2-20: TFTP Firmware Update Page Screenshot
Object Description
 TFTP Server IP Fill in your TFTP server IP address.
 Firmware File Name The name of firmware image.
(Maximum length : 24 characters)
Buttons
: Click to upgrade firmware.
DO NOT Power OFF the Managed Switch until the update progress is complete.
Do not quit the Firmware Upgrade Page without pressing the “OK” button after the image is
loaded. Or the system won’t apply the new firmware. User has to repeat the firmware
upgrade processes.
69
4.2.18 Save Startup Config
This function allows save the current configuration, thereby ensuring that the current active configuration can be used at the
next reboot screen in Figure 4-2-22 appears. After saving the configuratioin, the screen Figure 4-2-23 will appear.
Figure 4-2-22: Configuration Save Page Screenshot
Figure 4-2-23: Finish Saving Page Screenshot
4.2.19 Configuration Download
The switch stores its configuration in a number of text files in CLI format. The files are either virtual (RAM-based) or stored in
flash on the switch.
There are three system files:
 running-config: A virtual file that represents the currently active configuration on the switch. This file is volatile.
 startup-config: The startup configuration for the switch, read at boot time.
 default-config: A read-only file with vendor-specific configuration. This file is read when the system is restored to default
settings.
It is also possible to store up to two other files and apply them to running-config, thereby switching configuration.
Configuration Download page allows the download the running-config, startup-config and default-config on the switch. Please
refer to the Figure 4-2-24 shown below.
Figure 4-2-24: Configuration Download Page Screenshot
70
4.2.20 Configuration Upload
Configuration Upload page allows the upload the running-config and startup-config on the switch. Please refer to the Figure
4-2-25 shown below.
Figure 4-2-25: Configuration Upload Page Screenshot
If the destination is running-config, the file will be applied to the switch configuration. This can be done in two ways:
 Replace mode: The current configuration is fully replaced with the configuration in the uploaded file.
 Merge mode: The uploaded file is merged into running-config.
If the file system is full (i.e. contains the three system files mentioned above plus two other files), it is not possible to create new
files, but an existing file must be overwritten or another deleted first.
4.2.21 Configuration Activate
Configuration Activate page allows to activate the startup-config and default-config files present on the switch. Please refer to
the Figure 4-2-26 shown below.
Figure 4-2-26: Configuration Activate Page Screenshot
71
It is possible to activate any of the configuration files present on the switch, except for running-config which represents the
currently active configuration.
Select the file to activate and click . This will initiate the process of completely replacing the existing
configuration with that of the selected file.
4.2.22 Configuration Delete
Configuration Delete page allows to delete the startup-config and default-config files which stored in FLASH. If this is done and
the switch is rebooted without a prior Save operation, this effectively resets the switch to default configuration. Please refer to
the Figure 4-2-27 shown below.
Figure 4-2-27: Configuration Delete Page Screenshot
4.2.23 Image Select
This Page provides information about the active and alternate (backup) firmware images in the device, and allows you to revert
to the alternate image. The web Page displays two tables with information about the active and alternate firmware images. The
Image Select screen in Figure 4-2-28 appears.
In case the active firmware image is the alternate image, only the "Active Image" table is shown. In this
case, the Activate Alternate Image button is also disabled.
1. If the alternate image is active (due to a corruption of the primary image or by manual
intervention), uploading a new firmware image to the device will automatically use the primary
image slot and activate this.
2. The firmware version and date information may be empty for older firmware releases. This does
not constitute an error.
72
Figure 4-2-28: Software Image Selection Page Screenshot
Object Description
 Image The flash index name of the firmware image. The name of primary (preferred)
image is image, the alternate image is named image.bk.
 Version The version of the firmware image.
 Date The date where the firmware was produced.
Buttons
: Click to use the alternate image. This button may be disabled depending on system state.
4.2.24 Factory Default
You can reset the configuration of the Managed Switch on this Page. Only the IP configuration is retained. The new
configuration is available immediately, which means that no restart is necessary. The Factory Default screen in Figure 4-2-29
appears.
Figure 4-2-29: Factory Default Page Screenshot
73
Buttons
: Click to reset the configuration to Factory Defaults.
: Click to return to the Port State Page without resetting the configuration.
To reset the Managed Switch to the Factory default setting, you can also press the hardware reset button
at the front panel about 10 seconds. After the device be rebooted. You can login the management WEB
interface within the same subnet of 192.168.0.xx.
4.2.25 System Reboot
The Reboot Page enables the device to be rebooted from a remote location. Once the Reboot button is pressed, user have to
re-login the WEB interface about 60 seconds later, the System Reboot screen in Figure 4-2-30 appears.
Figure 4-2-30: System Reboot Page Screenshot
Buttons
: Click to reboot the system.
: Click to return to the Port State Page without rebooting the system.
You can also check the SYS LED at the front panel to identify whether the System is loaded completely or
not. If the SYS LED is blinking, then it is in the firmware load stage; if the SYS LED light is on, you can use
the WEB browser to login the Managed Switch.
74
4.3 Simple Network Management Protocol
4.3.1 SNMP Overview
The Simple Network Management Protocol (SNMP) is an application layer protocol that facilitates the exchange of management
information between network devices. It is part of the Transmission Control Protocol/Internet Protocol (TCP/IP) protocol suite.
SNMP enables network administrators to manage network performance, find and solve network problems, and plan for network
growth.
An SNMP-managed network consists of three key components: Network management stations (NMSs), SNMP agents,
Management information base (MIB) and network-management protocol：
■ Network management stations (NMSs)：Sometimes called consoles, these devices execute management applications
that monitor and control network elements. Physically, NMSs are usually engineering workstation-caliber computers with
fast CPUs, megapixel color displays, substantial memory, and abundant disk space. At least one NMS must be present in
each managed environment.

■ Agents：Agents are software modules that reside in network elements. They collect and store management information
such as the number of error packets received by a network element.

■ Management information base (MIB)：A MIB is a collection of managed objects residing in a virtual information store.
Collections of related managed objects are defined in specific MIB modules.

■ Network-management protocol：A management protocol is used to convey management information between agents
and NMSs. SNMP is the Internet community's de facto standard management protocol.
SNMP Operations
SNMP itself is a simple request/response protocol. NMSs can send multiple requests without receiving a response.
■ Get -- Allows the NMS to retrieve an object instance from the agent.
■ Set -- Allows the NMS to set values for object instances within an agent.
■ Trap -- Used by the agent to asynchronously inform the NMS of some event. The SNMPv2 trap message is designed to
replace the SNMPv1 trap message.
SNMP community
An SNMP community is the group that devices and management stations running SNMP belong to. It helps define where
75
information is sent. The community name is used to identify the group. A SNMP device or agent may belong to more than one
SNMP community. It will not respond to requests from management stations that do not belong to one of its communities. SNMP
default communities are:
。 Write = private
。 Read = public
Use the SNMP Menu to display or configure the Managed Switch's SNMP function. This section has the following items:
 System Configuration Configure SNMP on this Page.
 Trap Configuration Configure SNMP trap on this Page.
 System Information The system information is provided here.
 SNMPv3 Communities Configure SNMPv3 communities table on this Page.
 SNMPv3 Users Configure SNMPv3 users table on this Page.
 SNMPv3 Groups Configure SNMPv3 groups table on this Page.
 SNMPv3 Views Configure SNMPv3 views table on this Page.
 SNMPv3 Access Configure SNMPv3 accesses table on this Page.
4.3.2 SNMP System Configuration
Configure SNMP on this Page. The SNMP System Configuration screen in Figure 4-3-1 appears.
Figure 4-3-1: SNMP System Configuration Page Screenshot
Object Description
 Mode Indicates the SNMP mode operation. Possible modes are:
 Enabled: Enable SNMP mode operation.

 Disabled: Disable SNMP mode operation.
 Version Indicates the SNMP supported version. Possible versions are:
 SNMP v1: Set SNMP supported version 1.

 SNMP v2c: Set SNMP supported version 2c.
 SNMP v3: Set SNMP supported version 3.
76
 Read Community Indicates the community read access string to permit access to SNMP agent.
The allowed string length is 0 to 255, and the allowed content is the ASCII
characters from 33 to 126.
The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If
SNMP version is SNMPv3, the community string will be associated with SNMPv3
communities table. It provides more flexibility to configure security name than a
SNMPv1 or SNMPv2c community string. In addition to community string, a
particular range of source addresses can be used to restrict source subnet.
 Write Community Indicates the community write access string to permit access to SNMP agent.
The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If
SNMP version is SNMPv3, the community string will be associated with SNMPv3
communities table. It provides more flexibility to configure security name than a
SNMPv1 or SNMPv2c community string. In addition to community string, a
particular range of source addresses can be used to restrict source subnet.
 Engine ID Indicates the SNMPv3 engine ID. The string must contain an even number
between 10 and 64 hexadecimal digits, but all-zeros and all-'F's are not allowed.
Change of the Engine ID will clear all original local users.
Buttons
77
4.3.3 SNMP Trap Configuration
Configure SNMP trap on this Page. The SNMP Trap Configuration screen in Figure 4-3-2 appears.
Figure 4-3-2: SNMP Trap Configuration Page Screenshot
Object Description
 Trap Config Indicates which trap Configuration's name for configuring. The allowed string
length is 0 to 255, and the allowed content is ASCII characters from 33 to 126.
 Trap Mode Indicates the SNMP trap mode operation. Possible modes are:
 Enabled: Enable SNMP trap mode operation.

 Disabled: Disable SNMP trap mode operation.
 Trap Version Indicates the SNMP trap supported version. Possible versions are:
78
 SNMP v1: Set SNMP trap supported version 1.

 SNMP v2c: Set SNMP trap supported version 2c.
 SNMP v3: Set SNMP trap supported version 3.
 Trap Community Indicates the community access string when send SNMP trap packet. The
allowed string length is 0 to 255, and the allowed content is the ASCII characters
from 33 to 126.
 Trap Destination Indicates the SNMP trap destination address.
Address
 Trap Destination Port Indicates the SNMP trap destination port. SNMP Agent will send SNMP message
via this port, the port range is 1~65535.
 Trap Inform Mode Indicates the SNMP trap inform mode operation. Possible modes are:
 Enabled: Enable SNMP trap authentication failure.

 Disabled: Disable SNMP trap authentication failure.
 Trap Inform Timeout Indicates the SNMP trap inform timeout.
(seconds) The allowed range is 0 to 2147.
 Trap Inform Retry Indicates the SNMP trap inform retry times.
Times The allowed range is 0 to 255.
 Trap Probe Security Indicates the SNMPv3 trap probe security engine ID mode of operation. Possible
Engine ID values are:
 Enabled: Enable SNMP trap probe security engine ID mode of operation.

 Disabled: Disable SNMP trap probe security engine ID mode of operation.
 Trap Security Engine Indicates the SNMP trap security engine ID. SNMPv3 sends traps and informs
ID using USM for authentication and privacy. A unique engine ID for these traps and
informs is needed. When "Trap Probe Security Engine ID" is enabled, the ID will
be probed automatically. Otherwise, the ID specified in this field is used. The

string must contain an even number(in hexadecimal format) with number of digits
between 10 and 64, but all-zeros and all-'F's are not allowed.
 Trap Security Name Indicates the SNMP trap security name. SNMPv3 traps and informs using USM
for authentication and privacy. A unique security name is needed when traps and
informs are enabled.
 System Enable/disable that the Interface group's traps. Possible traps are:
 Warm Start: Enable/disable Warm Start trap.

 Cold Start: Enable/disable Cold Start trap.
 Interface Indicates that the Interface group's traps. Possible traps are:
 Link Up: Enable/disable Link up trap.

 Link Down: Enable/disable Link down trap.
 LLDP: Enable/disable LLDP trap.
 AAA Indicates that the AAA group's traps. Possible traps are:
Authentication Fail : Enable/disable SNMP trap authentication failure trap.
79
 Switch Indicates that the Switch group's traps. Possible traps are:
 STP: Enable/disable STP trap.

 RMON: Enable/disable RMON trap.
Buttons
4.3.4 SNMP System Information
The switch system information is provided here. The SNMP System Information screen in Figure 4-3-3 appears.
Figure 4-3-3: System Information Configuration Page Screenshot
Object Description
 System Contact The textual identification of the contact person for this managed node, together
with information on how to contact this person. The allowed string length is 0 to
255, and the allowed content is the ASCII characters from 32 to 126.
 System Name An administratively assigned name for this managed node. By convention, this is
the node's fully-qualified domain name. A domain name is a text string drawn
from the alphabet (A-Za-z), digits (0-9), minus sign (-). No space characters are
permitted as part of a name. The first character must be an alpha character. And
the first or last character must not be a minus sign. The allowed string length is 0
to 255.
 System Location The physical location of this node(e.g., telephone closet, 3rd floor). The allowed
string length is 0 to 255, and the allowed content is the ASCII characters from 32
to 126.
80
4.3.5 SNMPv3 Configuration
4.3.5.1 SNMPv3 Communities
Configure SNMPv3 communities table on this Page. The entry index key is Community. The SNMPv3 Communities screen in
Figure 4-3-4: SNMPv3 Communities Configuration Page Screenshot
Object Description
 Delete Check to delete the entry. It will be deleted during the next save.
 Community Indicates the community access string to permit access to SNMPv3 agent. The
allowed string length is 1 to 32, and the allowed content is ASCII characters from
33 to 126. The community string will be treated as security name and map a
SNMPv1 or SNMPv2c community string.
 Source IP Indicates the SNMP access source address. A particular range of source
addresses can be used to restrict source subnet when combined with source
mask.
 Source Mask Indicates the SNMP access source address mask.
Buttons
: Click to add a new community entry.
81
4.3.5.2 SNMPv3 Users
Configure SNMPv3 users table on this Page. The entry index keys are Engine ID and User Name. The SNMPv3 Users screen
in Figure 4-3-5 appears.
Figure 4-3-5: SNMPv3 Users Configuration Page Screenshot
Object Description
 Engine ID An octet string identifying the engine ID that this entry should belong to. The
string must contain an even number(in hexadecimal format) with number of digits
between 10 and 64, but all-zeros and all-'F's are not allowed. The SNMPv3
architecture uses the User-based Security Model (USM) for message security
and the View-based Access Control Model (VACM) for access control. For the
USM entry, the usmUserEngineID and usmUserName are the entry's keys.
In a simple agent, usmUserEngineID is always that agent's own snmpEngineID
value. The value can also take the value of the snmpEngineID of a remote SNMP
engine with which this user can communicate. In other words, if user engine ID
equal system engine ID then it is local user; otherwise it's remote user.
 User Name A string identifying the user name that this entry should belong to. The allowed
string length is 1 to 32, and the allowed content is ASCII characters from 33 to
126.
 Security Level Indicates the security model that this entry should belong to. Possible security
models are:
 NoAuth, NoPriv: None authentication and none privacy.

 Auth, NoPriv: Authentication and none privacy.
 Auth, Priv: Authentication and privacy.
The value of security level cannot be modified if entry already exist. That means
must first ensure that the value is set correctly.
 Authentication Indicates the authentication protocol that this entry should belong to. Possible
Protocol authentication protocol are:
 None: None authentication protocol.
82
 MD5: An optional flag to indicate that this user using MD5 authentication
protocol.
 SHA: An optional flag to indicate that this user using SHA authentication
protocol.
The value of security level cannot be modified if entry already exist. That means
must first ensure that the value is set correctly.
 Authentication A string identifying the authentication pass phrase. For MD5 authentication
Password protocol, the allowed string length is 8 to 32. For SHA authentication protocol, the
allowed string length is 8 to 40. The allowed content is the ASCII characters from
33 to 126.
 Privacy Protocol Indicates the privacy protocol that this entry should belong to. Possible privacy
protocol are:
 None: None privacy protocol.

 DES: An optional flag to indicate that this user using DES authentication
protocol.
 AES: An optional flag to indicate that this user uses AES authentication
protocol.
 Privacy Password A string identifying the privacy pass phrase. The allowed string length is 8 to 32,
and the allowed content is the ASCII characters from 33 to 126.
Buttons
: Click to add a new user entry.
4.3.5.3 SNMPv3 Groups
Configure SNMPv3 groups table on this Page. The entry index keys are Security Model and Security Name. The SNMPv3
Groups screen in Figure 4-3-6 appears.
Figure 4-3-6: SNMPv3 Groups Configuration Page Screenshot
83
Object Description
 Security Model Indicates the security model that this entry should belong to. Possible security
models are:
 v1: Reserved for SNMPv1.

 v2c: Reserved for SNMPv2c.
 usm: User-based Security Model (USM).
 Security Name A string identifying the security name that this entry should belong to.
 Group Name A string identifying the group name that this entry should belong to.
Buttons
: Click to add a new group entry.
4.3.5.4 SNMPv3 Views
Configure SNMPv3 views table on this Page. The entry index keys are View Name and OID Subtree. The SNMPv3 Views
Figure 4-3-7: SNMPv3 Views Configuration Page Screenshot
Object Description
84
 View Name A string identifying the view name that this entry should belong to. The allowed
to 126.
 View Type Indicates the view type that this entry should belong to. Possible view type are:
 included: An optional flag to indicate that this view subtree should be

included.
 excluded: An optional flag to indicate that this view subtree should be

excluded.
In general, if a view entry's view type is 'excluded', it should be exist another view
entry which view type is 'included' and it's OID subtree overstep the 'excluded'
view entry.
 OID Subtree The OID defining the root of the subtree to add to the named view. The allowed
OID length is 1 to 128. The allowed string content is digital number or asterisk(*).
Buttons
: Click to add a new view entry.
4.3.5.5 SNMPv3 Access
Configure SNMPv3 accesses table on this Page. The entry index keys are Group Name, Security Model and Security Level.
The SNMPv3 Access screen in Figure 4-3-8 appears.
Figure 4-3-8: SNMPv3 Accesses Configuration Page Screenshot
Object Description
85
 Group Name A string identifying the group name that this entry should belong to. The allowed
to 126.
 Security Model Indicates the security model that this entry should belong to. Possible security
models are:
 any: Accepted any security model (v1|v2c|usm).

 v1: Reserved for SNMPv1.
 v2c: Reserved for SNMPv2c.
 usm: User-based Security Model (USM)
 Security Level Indicates the security model that this entry should belong to. Possible security
models are:
 NoAuth, NoPriv: None authentication and none privacy.

 Auth, NoPriv: Authentication and none privacy.
 Auth, Priv: Authentication and privacy.
 Read View Name The name of the MIB view defining the MIB objects for which this request may
request the current values. The allowed string length is 1 to 32, and the allowed
content is the ASCII characters from 33 to 126.
 Write View Name The name of the MIB view defining the MIB objects for which this request may
potentially SET new values. The allowed string length is 1 to 32, and the allowed
content is the ASCII characters from 33 to 126.
Buttons
: Click to add a new access entry.
86
4.4 Port Management

Use the Port Menu to display or configure the Managed Switch's ports. This section has the following items:
 Port Configuration Configures port connection settings
 Port Statistics Overview Lists Ethernet and RMON port statistics
 Port Statistics Detail Lists Ethernet and RMON port statistics
 SFP Module Information Display SFP information
 Port Mirror Sets the source and target ports for mirroring
4.4.1 Port Configuration
This Page displays current port configurations. Ports can also be configured here. The Port Configuration screen in Figure 4-4-1
appears.
Figure 4-4-1: Port Configuration Page Screenshot
Object Description
 Port This is the logical port number for this row.
 Port Description Indicates the per port description.
 Link The current link state is displayed graphically. Green indicates the link is up and
red that it is down.
 Current Link Speed Provides the current link speed of the port.
87
 Configured Link Speed Select any available link speed for the given switch port. Draw the menu bar to
select the mode.
 Auto - Setup Auto negotiation for copper interface.
 10Mbps HDX - Force sets 10Mbps/Half-Duplex mode.
 10Mbps FDX - Force sets 10Mbps/Full-Duplex mode.
 100Mbps HDX - Force sets 100Mbps/Half-Duplex mode.
 100Mbps FDX - Force sets 100Mbps/Full-Duplex mode.
 1Gbps FDX - Force sets 10000Mbps/Full-Duplex mode.
 Auto Fiber (10G) – Setup 10G firber port for negotiation

automatically.
 Disable - Shutdown the port manually.
 Flow Control When Auto Speed is selected on a port, this section indicates the flow control
capability that is advertised to the link partner.
When a fixed-speed setting is selected, that is what is used. The Current Rx
column indicates whether pause frames on the port are obeyed, and the Current
Tx column indicates whether pause frames on the port are transmitted. The Rx
and Tx settings are determined by the result of the last Auto-Negotiation.
Check the configured column to use flow control. This setting is related to the
setting for Configured Link Speed.
 Maximum Frame Size Enter the maximum frame size allowed for the switch port, including FCS. The
allowed range is 1518 bytes to 10056 bytes.
 Excessive Collision Configure port transmit collision behavior.
Mode  Discard: Discard frame after 16 collisions (default).
 Restart: Restart back off algorithm after 16 collisions.
When set each port to run at 100M Full, 100M Half, 10M Full, and 10M Half-speed modes. The
Auto-MDIX function will disable.
Buttons
: Click to refresh the Page. Any changes made locally will be undone.
88
4.4.2 Port Statistics Overview
This Page provides an overview of general traffic statistics for all switch ports. The Port Statistics Overview screen in Figure
4-4-2 appears.
Figure 4-4-2: Port Statistics Overview Page Screenshot
The displayed counters are:
Object Description
 Port The logical port for the settings contained in the same row.
 Packets The number of received and transmitted packets per port.
 Bytes The number of received and transmitted bytes per port.
 Errors The number of frames received in error and the number of incomplete
transmissions per port.
 Drops The number of frames discarded due to ingress or egress congestion.
 Filtered The number of received frames filtered by the forwarding process.
Buttons
: Download the Port Statistics Overview result as EXECL file.
: Clears the counters for all ports.
: Print the Port Statistics Overview result.
Auto-refresh : Check this box to enable an automatic refresh of the Page at regular intervals.
89
4.4.3 Port Statistics Detail
This Page provides detailed traffic statistics for a specific switch port. Use the port select box to select which switch port details
to display. The displayed counters are the totals for receive and transmit, the size counters for receive and transmit, and the
error counters for receive and transmit. The Port Statistics Detail screen in Figure 4-4-3 appears.
Figure 4-4-3: Detailed Port Statistics Port 1 Page Screenshot
Receive Total and Transmit Total
Object Description
 Rx and Tx Packets The number of received and transmitted (good and bad) packets
 Rx and Tx Octets The number of received and transmitted (good and bad) bytes, including FCS,
but excluding framing bits.
 Rx and Tx Unicast The number of received and transmitted (good and bad) unicast packets.
 Rx and Tx Multicast The number of received and transmitted (good and bad) multicast packets.
 Rx and Tx Broadcast The number of received and transmitted (good and bad) broadcast packets.
 Rx and Tx Pause A count of the MAC Control frames received or transmitted on this port that has
an opcode indicating a PAUSE operation.
90
Receive and Transmit Size Counters
The number of received and transmitted (good and bad) packets split into categories based on their respective frame
sizes.
Receive and Transmit Queue Counters
The number of received and transmitted packets per input and output queue.
Receive Error Counters
Object Description
 Rx Drops The number of frames dropped due to lack of receive buffers or egress
congestion.
 Rx CRC/Alignment The number of frames received with CRC or alignment errors.
 Rx Undersize The number of short frames received with valid CRC.
 Rx Oversize The number of long frames received with valid CRC.
 Rx Fragments The number of short frames received with invalid CRC.
 Rx Jabber The number of long frames received with invalid CRC.
 Rx Filtered The number of received frames filtered by the forwarding process.
Short frames are frames that are smaller than 64 bytes.

Long frames are frames that are longer than the configured maximum
frame length for this port.
1 Short frames are frames that are smaller than 64 bytes.
2 Long frames are frames that are longer than the configured maximum frame length for this port.
Transmit Error Counters
Object Description
 Tx Drops The number of frames dropped due to output buffer congestion.
 Tx Late/Exc. Coll. The number of frames dropped due to excessive or late collisions.
Buttons
91
4.4.4 SFP Module Information
The WGSW-48040HP has supported the SFP module with digital diagnostics monitoring (DDM) function, this feature is also
known as digital optical monitoring (DOM). You can check the physical or operational status of an SFP module via the SFP
Module Information Page. This Page shows the operational status, such as the transceiver type, speed, wavelength, optical
output power, optical input power, temperature, laser bias current and transceiver supply voltage in real time. You can also use
the hyperlink of port no. to check the statistics on a speficic interface. The SFP Module Information screen in Figure 4-4-4
appears.
Figure 4-4-4: SFP Module Information for Switch Page Screenshot
Object Description
 Type Display the type of current SFP module, the possible types are:
 10GBASE-SR
 10GBASE-LR
 1000BASE-SX
 1000BASE-LX
 100BASE-FX
 Speed Display the spedd of current SFP module, the speed value or description is get
from the SFP module. Different vendors SFP modules might shows different
speed information.
 Wave Length(nm) Display the wavelength of current SFP module, the wavelength value is get from
the SFP module. Use this column to check if the wavelength values of two nodes
are the matched while the fiber connection is failed.
 Distance(m) Display the supports distance of current SFP module, the distance value is get
from the SFP module.
 Temperature(C) Display the temperature of current SFP DDM module, the temperature value is
– SFP DDM Module Only get from the SFP DDM module.
92
 Voltage(V) Display the voltage of current SFP DDM module, the voltage value is get from the
– SFP DDM Module Only SFP DDM module.
 Current(mA) Display the Ampere of current SFP DDM module, the Ampere value is get from
– SFP DDM Module Only the SFP DDM module.
 TX power(dBm) Display the TX power of current SFP DDM module, the TX power value is get
– SFP DDM Module Only from the SFP DDM module.
 RX power(dBm) Display the RX power of current SFP DDM module, the RX power value is get
– SFP DDM Module Only from the SFP DDM module.
Buttons
SFP Monitor Event Alert: send trap
Warning Temperature: degrees C
Check SFP Monitor Event Alert box; it will be in accordance with your warning temperature setting and allows users to
record message out via SNMP Trap.
4.4.5 Port Mirror
Configure port Mirroring on this Page. This function provide to monitoring network traffic that forwards a copy of each incoming
or outgoing packet from one port of a network Switch to another port where the packet can be studied. It enables the manager to
keep close track of switch performance and alter it if necessary.
 To debug network problems, selected traffic can be copied, or mirrored, to a mirror port where a frame analyzer can be
attached to analyze the frame flow.
 The Managed Switch can unobtrusively mirror traffic from any port to a monitor port. You can then attach a protocol
analyzer or RMON probe to this port to perform traffic analysis and verify connection integrity.
93
Figure 4-4-7: Port Mirror Application
The traffic to be copied to the mirror port is selected as follows:

 All frames received on a given port (also known as ingress or source mirroring).
 All frames transmitted on a given port (also known as egress or destination mirroring).
Mirror Port Configuration

The Port Mirror screen in Figure 4-4-8 appears.
Figure 4-4-8: Mirror Configuration Page Screenshot
Object Description
 Port to mirror on Frames from ports that have either source (rx) or destination (tx) mirroring enabled are
mirrored to this port. Disabled disables mirroring.
94
 Mode Select mirror mode.
■ Rx only: Frames received at this port are mirrored to the mirroring port. Frames
transmitted are not mirrored.
■ Tx only: Frames transmitted from this port are mirrored to the mirroring port. Frames
received are not mirrored.
■ Disabled: Neither frames transmitted or frames received are mirrored.
■ Both: Frames received and frames transmitted are mirrored to the mirror port.
For a given port, a frame is only transmitted once. It is therefore not possible to mirror Tx frames on
the mirror port. Because of this, mode for the selected mirror port is limited to Disabled or Rx only.
Buttons
95
4.5 Link Aggregation

Port Aggregation optimizes port usage by linking a group of ports together to form a single Link Aggregated Groups (LAGs). Port
Aggregation multiplies the bandwidth between the devices, increases port flexibility, and provides link redundancy.
Each LAG is composed of ports of the same speed, set to full-duplex operations. Ports in a LAG, can be of different media types
(UTP/Fiber, or different fiber types), provided they operate at the same speed.
Aggregated Links can be assigned manually (Port Trunk) or automatically by enabling Link Aggregation Control Protocol
(LACP) on the relevant links.
Aggregated Links are treated by the system as a single logical port. Specifically, the Aggregated Link has similar port attributes
to a non-aggregated port, including auto-negotiation, speed, Duplex setting, etc.
The device supports the following Aggregation links :
 Static LAGs (Port Trunk) – Force aggregared selected ports to be a trunk group.
 Link Aggregation Control Protocol (LACP) LAGs - LACP LAG negotiate Aggregated Port links with other LACP
ports located on a different device. If the other device ports are also LACP ports, the devices establish a LAG
between them.
Figure 4-5-1: Link Aggregation
96
The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner
Systems that require high speed redundant links. Link aggregation lets you group up to eight consecutive ports into a single
dedicated connection. This feature can expand bandwidth to a device on the network. LACP operation requires full-duplex mode,
more detail information refer to the IEEE 802.3ad standard.
Port link aggregations can be used to increase the bandwidth of a network connection or to ensure fault recovery. Link
aggregation lets you group up to 4 consecutive ports into a single dedicated connection between any two the Switch or other
Layer 2 switches. However, before making any physical connections between devices, use the Link aggregation Configuration
menu to specify the link aggregation on the devices at both ends. When using a port link aggregation, note that:
 The ports used in a link aggregation must all be of the same media type (RJ45, 100 Mbps fiber).
 The ports that can be assigned to the same link aggregation have certain other restrictions (see below).
 Ports can only be assigned to one link aggregation.
 The ports at both ends of a connection must be configured as link aggregation ports.
 None of the ports in a link aggregation can be configured as a mirror source port or a mirror target port.
 All of the ports in a link aggregation have to be treated as a whole when moved from/to, added or deleted from a VLAN.
 The Spanning Tree Protocol will treat all the ports in a link aggregation as a whole.
 Enable the link aggregation prior to connecting any cable between the switches to avoid creating a data loop.
 Disconnect all link aggregation port cables or disable the link aggregation ports before removing a port link aggregation to
avoid creating a data loop.
It allows a maximum of 10 ports to be aggregated at the same time. The Managed Switch support Gigabit Ethernet ports (up to 5
groups). If the group is defined as a LACP static link aggregationing group, then any extra ports selected are placed in a standby
mode for redundancy if one of the other ports fails. If the group is defined as a local static link aggregationing group, then the
number of ports must be the same as the group member ports.
The aggregation code ensures that frames belonging to the same frame flow (for example, a TCP connection) are always
forwarded on the same link aggregation member port. Reording of frames within a flow is therefore not possible. The
aggregation code is based on the following information:
 Source MAC
 Destination MAC
 Source and destination IPv4 address.
 Source and destination TCP/UDP ports for IPv4 packets
Normally, all 5 contributions to the aggregation code should be enabled to obtain the best traffic distribution among the link
aggregation member ports. Each link aggregation may consist of up to 10 member ports. Any quantity of link aggregation s may
be configured for the device (only limited by the quantity of ports on the device.) To configure a proper traffic distribution, the
ports within a link aggregation must use the same link speed.
97
4.5.1 Static Aggregation
This Page is used to configure the Aggregation hash mode and the aggregation group. The aggregation hash mode settings are
global.
Hash Code Contributors

The Static Aggeration screen in Figure 4-5-2 appears.
Figure 4-5-2 : Aggregation Mode Configuration Page Screenshot
Object Description
 Source MAC Address The Source MAC address can be used to calculate the destination port for the
frame. Check to enable the use of the Source MAC address, or uncheck to
disable. By default, Source MAC Address is enabled.
 Destination MAC The Destination MAC Address can be used to calculate the destination port for
Address the frame. Check to enable the use of the Destination MAC Address, or uncheck
to disable. By default, Destination MAC Address is disabled.
 IP Address The IP address can be used to calculate the destination port for the frame. Check
to enable the use of the IP Address, or uncheck to disable. By default, IP Address
is enabled.
 TCP/UDP Port Number The TCP/UDP port number can be used to calculate the destination port for the
frame. Check to enable the use of the TCP/UDP Port Number, or uncheck to
disable. By default, TCP/UDP Port Number is enabled.
Static Aggregation Group Configuration

The Aggregation Group Configuration screen in Figure 4-5-3 appears.
98
Figure 4-5-3: Aggregation Group Configuration Page Screenshot
.Object Description
 Group ID Indicates the group ID for the settings contained in the same row. Group ID
"Normal" indicates there is no aggregation. Only one group ID is valid per port.
 Port Members Each switch port is listed for each group ID. Select a radio button to include a port
in an aggregation, or clear the radio button to remove the port from the
aggregation. By default, no ports belong to any aggregation group.
Buttons
4.5.2 LACP Configuration
Link Aggregation Control Protocol (LACP) - LACP LAG negotiate Aggregated Port links with other LACP ports located on a
99
different device. LACP allows switches connected to each other to discover automatically whether any ports are member of the
same LAG.
This Page allows the user to inspect the current LACP port configurations, and possibly change them as well. The LACP
Configuration screen in Figure 4-5-4 appears.
Figure 4-5-4 : LACP Port Configuration Page Screenshot
Object Description
 Port The switch port number.
 LACP Enabled Controls whether LACP is enabled on this switch port. LACP will form an
aggregation when 2 or more ports are connected to the same partner.
 Key The Key value incurred by the port, range 1-65535 . The Auto setting will set the
key as appropriate by the physical link speed, 10Mb = 1, 100Mb = 2, 1Gb = 3.
Using the Specific setting, a user-defined value can be entered. Ports with the
same Key value can participate in the same aggregation group, while ports with
different keys cannot.
The default setting is “Auto”
 Role The Role shows the LACP activity status. The Active will transmit LACP packets
each second, while Passive will wait for a LACP packet from a partner (speak if
spoken to).
 Timeout The Timeout controls the period between BPDU transmissions. Fast will transmit
LACP packets each second, while Slow will wait for 30 seconds before sending a
LACP packet.
100
 Priority The Prio controls the priority of the port. If the LACP partner wants to form a
larger group than is supported by this device then this parameter will control
which ports will be active and which ports will be in a backup role. Lower number
means greater priority.
Buttons
4.5.3 LACP System Status
This Page provides a status overview for all LACP instances. The LACP Status Page display the current LACP aggregation
Groups and LACP Port status. The LACP System Status screen in Figure 4-5-5 appears.
Figure 4-5-5: LACP System Status Page Screenshot
Object Description
 Aggr ID The Aggregation ID associated with this aggregation instance.
For LLAG the id is shown as 'isid:aggr-id' and for GLAGs as 'aggr-id'
 Partner System ID The system ID (MAC address) of the aggregation partner.
 Partner Key The Key that the partner has assigned to this aggregation ID.
 Partner Priority The priority of the aggregation partner.
 Last changed The time since this aggregation changed.
 Local Ports Shows which ports are a part of this aggregation for this switch.
Buttons
Auto-refresh : Automatic refresh occurs every 3 seconds.
101
4.5.4 LACP Port Status
This Page provides a status overview for LACP status for all ports. The LACP Port Status screen in Figure 4-5-6 appears.
Figure 4-5-6: LACP Status Page Screenshot
Object Description
 LACP 'Yes' means that LACP is enabled and the port link is up. 'No' means that LACP is
not enabled or that the port link is down. 'Backup' means that the port could not
join the aggregation group but will join if other port leaves. Meanwhile it's LACP
status is disabled.
 Key The key assigned to this port. Only ports with the same key can aggregate
together.
 Aggr ID The Aggregation ID assigned to this aggregation group.
 Partner System ID The partner’s System ID (MAC address).
 Partner Port The partner’s port number connected to this port.
 Partner Priority The partner's port priority.
Buttons
102
4.5.5 LACP Port Statistics
This Page provides an overview for LACP statistics for all ports. The LACP Port Statistics screen in Figure 4-5-7 appears.
Figure 4-5-7: LACP Statistics Page Screenshot
Object Description
 LACP Received Shows how many LACP frames have been sent from each port.
 LACP Transmitted Shows how many LACP frames have been received at each port.
 Discarded Shows how many unknown or illegal LACP frames have been discarded at each
port.
Buttons
103
4.6 VLAN
4.6.1 VLAN Overview
A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical
layout. VLAN can be used to combine any collection of LAN segments into an autonomous user group that appears as a single
LAN. VLAN also logically segment the network into different broadcast domains so that packets are forwarded only between
ports within the VLAN. Typically, a VLAN corresponds to a particular subnet, although not necessarily.
VLAN can enhance performance by conserving bandwidth, and improve security by limiting traffic to specific domains.
A VLAN is a collection of end nodes grouped by logic instead of physical location. End nodes that frequently communicate with
each other are assigned to the same VLAN, regardless of where they are physically on the network. Logically, a VLAN can be
equated to a broadcast domain, because broadcast packets are forwarded to only members of the VLAN on which the
broadcast was initiated.
1. No matter what basis is used to uniquely identify end nodes and assign these nodes VLAN
membership, packets cannot cross VLAN without a network device performing a routing
function between the VLAN.
2. The Managed Switch supports IEEE 802.1Q VLAN. The port untagging function can be used
to remove the 802.1 tag from packet headers to maintain compatibility with devices that are
tag-unaware..
The Managed Switch's default is to assign all ports to a single 802.1Q VLAN named
DEFAULT_VLAN. As new VLAN is created, the member ports assigned to the new VLAN will be
removed from the DEFAULT_ VLAN port member list. The DEFAULT_VLAN has a VID = 1.
This section has the following items:
 VLAN Port Configuration Enables VLAN group
 VLAN Membership Status Displays VLAN membership status
 VLAN Port Status Displays VLAN port status
 Private VLAN Creates/removes primary or community VLANs
 Port Isolation Enables/disablse port isolation on port
 MAC-based VLAN Configures the MAC-based VLAN entries
 MAC-based VLAN Status Displays MAC-based VLAN entries
 Protocol-based VLAN Configures the protocol-based VLAN entries
 Protocol-based VLAN
Displays the protocol-based VLAN entries
Membership
104
4.6.2 IEEE 802.1Q VLAN
In large networks, routers are used to isolate broadcast traffic for each subnet into separate domains. This Managed Switch
provides a similar service at Layer 2 by using VLANs to organize any group of network nodes into separate broadcast domains.
VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This also
provides a more secure and cleaner network environment.
An IEEE 802.1Q VLAN is a group of ports that can be located anywhere in the network, but communicate as though they belong
to the same physical segment.
VLANs help to simplify network management by allowing you to move devices to a new VLAN without having to change any
physical connections. VLANs can be easily organized to reflect departmental groups (such as Marketing or R&D), usage groups
(such as e-mail), or multicast groups (used for multimedia applications such as videoconferencing).
VLANs provide greater network efficiency by reducing broadcast traffic, and allow you to make network changes without having
to update IP addresses or IP subnets. VLANs inherently provide a high level of network security since traffic must pass through
a configured Layer 3 link to reach a different VLAN.
This Managed Switch supports the following VLAN features:
 Up to 255 VLANs based on the IEEE 802.1Q standard
 Port overlapping, allowing a port to participate in multiple VLANs
 End stations can belong to multiple VLANs
 Passing traffic between VLAN-aware and VLAN-unaware devices
 Priority tagging
■ IEEE 802.1Q Standard

IEEE 802.1Q (tagged) VLAN are implemented on the Switch. 802.1Q VLAN require tagging, which enables them to span the
entire network (assuming all switches on the network are IEEE 802.1Q-compliant).
VLAN allow a network to be segmented in order to reduce the size of broadcast domains. All packets entering a VLAN will only
be forwarded to the stations (over IEEE 802.1Q enabled switches) that are members of that VLAN, and this includes broadcast,
multicast and unicast packets from unknown sources.
VLAN can also provide a level of security to your network. IEEE 802.1Q VLAN will only deliver packets between stations that are
members of the VLAN. Any port can be configured as either tagging or untagging.:
 The untagging feature of IEEE 802.1Q VLAN allows VLAN to work with legacy switches that don't recognize VLAN tags
in packet headers.
 The tagging feature allows VLAN to span multiple 802.1Q-compliant switches through a single physical connection and
allows Spanning Tree to be enabled on all ports and work normally.
Some relevant terms:
- Tagging - The act of putting 802.1Q VLAN information into the header of a packet.
- Untagging - The act of stripping 802.1Q VLAN information out of the packet header.
105
■ 802.1Q VLAN Tags

The figure below shows the 802.1Q VLAN tag. There are four additional octets inserted after the source MAC address. Their
presence is indicated by a value of 0x8100 in the Ether Type field. When a packet's Ether Type field is equal to 0x8100, the
packet carries the IEEE 802.1Q/802.1p tag. The tag is contained in the following two octets and consists of 3 bits of user priority,
1 bit of Canonical Format Identifier (CFI - used for encapsulating Token Ring packets so they can be carried across Ethernet
backbones), and 12 bits of VLAN ID (VID). The 3 bits of user priority are used by 802.1p. The VID is the VLAN identifier and is
used by the 802.1Q standard. Because the VID is 12 bits long, 4094 unique VLAN can be identified.
The tag is inserted into the packet header making the entire packet longer by 4 octets. All of the information originally contained
in the packet is retained.
802.1Q Tag
User Priority CFI VLAN ID (VID)
3 bits 1 bit 12 bits
TPID (Tag Protocol Identifier) TCI (Tag Control Information)
2 bytes 2 bytes
Preamble Destination Source VLAN TAG Ethernet Data FCS
Address Address Type
6 bytes 6 bytes 4 bytes 2 bytes 46-1500 bytes 4 bytes
The Ether Type and VLAN ID are inserted after the MAC source address, but before the original Ether Type/Length or Logical
Link Control. Because the packet is now a bit longer than it was originally, the Cyclic Redundancy Check (CRC) must be
recalculated.
Adding an IEEE802.1Q Tag
Dest. Addr. Src. Addr. Length/E. type Data Old CRC Original Ethernet
Dest. Addr. Src. Addr. E. type Tag Length/E. type Data New CRC
New Tagged Packet
Priority CFI VLAN ID
■ Port VLAN ID
Packets that are tagged (are carrying the 802.1Q VID information) can be transmitted from one 802.1Q compliant network
device to another with the VLAN information intact. This allows 802.1Q VLAN to span network devices (and indeed, the entire
network – if all network devices are 802.1Q compliant).
106
Every physical port on a switch has a PVID. 802.1Q ports are also assigned a PVID, for use within the switch. If no VLAN are
defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1. Untagged packets are assigned the
PVID of the port on which they were received. Forwarding decisions are based upon this PVID, in so far as VLAN are concerned.
Tagged packets are forwarded according to the VID contained within the tag. Tagged packets are also assigned a PVID, but the
PVID is not used to make packet forwarding decisions, the VID is.
Tag-aware switches must keep a table to relate PVID within the switch to VID on the network. The switch will compare the VID of
a packet to be transmitted to the VID of the port that is to transmit the packet. If the two VID are different the switch will drop the
packet. Because of the existence of the PVID for untagged packets and the VID for tagged packets, tag-aware and tag-unaware
network devices can coexist on the same network.
A switch port can have only one PVID, but can have as many VID as the switch has memory in its VLAN table to store them.
Because some devices on a network may be tag-unaware, a decision must be made at each port on a tag-aware device before
packets are transmitted – should the packet to be transmitted have a tag or not? If the transmitting port is connected to a
tag-unaware device, the packet should be untagged. If the transmitting port is connected to a tag-aware device, the packet
should be tagged.
■ Default VLANs
The Switch initially configures one VLAN, VID = 1, called "default." The factory default setting assigns all ports on the Switch to
the "default". As new VLAN are configured in Port-based mode, their respective member ports are removed from the "default."
■ Assigning Ports to VLANs

Before enabling VLANs for the switch, you must first assign each port to the VLAN group(s) in which it will participate. By default
all ports are assigned to VLAN 1 as untagged ports. Add a port as a tagged port if you want it to carry traffic for one or more
VLANs, and any intermediate network devices or the host at the other end of the connection supports VLANs. Then assign ports
on the other VLAN-aware network devices along the path that will carry this traffic to the same VLAN(s), either manually or
dynamically using GVRP. However, if you want a port on this switch to participate in one or more VLANs, but none of the
intermediate network devices nor the host at the other end of the connection supports VLANs, then you should add this port to
the VLAN as an untagged port.
VLAN-tagged frames can pass through VLAN-aware or VLAN-unaware network interconnection
devices, but the VLAN tags should be stripped off before passing it on to any end-node host that
does not support VLAN tagging.
■ VLAN Classification
When the switch receives a frame, it classifies the frame in one of two ways. If the frame is untagged, the switch assigns the
frame to an associated VLAN (based on the default VLAN ID of the receiving port). But if the frame is tagged, the switch uses
the tagged VLAN ID to identify the port broadcast domain of the frame.
107
■ Port Overlapping
Port overlapping can be used to allow access to commonly shared network resources among different VLAN groups, such as
file servers or printers. Note that if you implement VLANs which do not overlap, but still need to communicate, you can connect
them by enabled routing on this switch.
■ Untagged VLANs
Untagged (or static) VLANs are typically used to reduce broadcast traffic and to increase security. A group of network users
assigned to a VLAN form a broadcast domain that is separate from other VLANs configured on the switch. Packets are
forwarded only between ports that are designated for the same VLAN. Untagged VLANs can be used to manually isolate user
groups or subnets.
4.6.3 VLAN Port Configuration
This Page is used for configuring the Managed Switch port VLAN. The VLAN per Port Configuration Page contains fields for
managing ports that are part of a VLAN. The port default VLAN ID (PVID) is configured on the VLAN Port Configuration Page.
All untagged packets arriving to the device are tagged by the ports PVID.
Understand nomenclature of the Switch

■ IEEE 802.1Q Tagged and Untagged
Every port on an 802.1Q compliant switch can be configured as tagged or untagged.
 Tagged: Ports with tagging enabled will put the VID number, priority and other VLAN information into the
header of all packets that flow into those ports. If a packet has previously been tagged, the port
will not alter the packet, thus keeping the VLAN information intact. The VLAN information in the
tag can then be used by other 802.1Q compliant devices on the network to make
packet-forwarding decisions.
 Untagged: Ports with untagging enabled will strip the 802.1Q tag from all packets that flow into those
ports. If the packet doesn't have an 802.1Q VLAN tag, the port will not alter the packet. Thus,
all packets received by and forwarded by an untagging port will have no 802.1Q VLAN
information. (Remember that the PVID is only used internally within the Switch). Untagging is
used to send packets from an 802.1Q-compliant network device to a non-compliant network
device.
Frame Income
Income Frame is tagged Income Frame is untagged
Frame Leave
Leave port is tagged Frame remains tagged Tag is inserted
Leave port is untagged Tag is removed Frame remain untagged
Table 4-6-1: Ingress / Egress Port with VLAN VID Tag / Untag Table
108
■ IEEE 802.1Q Tunneling (Q-in-Q)

IEEE 802.1Q Tunneling (QinQ) is designed for service providers carrying traffic for multiple customers across their networks.
QinQ tunneling is used to maintain customer-specific VLAN and Layer 2 protocol configurations even when different customers
use the same internal VLAN IDs. This is accomplished by inserting Service Provider VLAN (SPVLAN) tags into the customer’s
frames when they enter the service provider’s network, and then stripping the tags when the frames leave the network.
A service provider’s customers may have specific requirements for their internal VLAN IDs and number of VLANs supported.
VLAN ranges required by different customers in the same service-provider network might easily overlap, and traffic passing
through the infrastructure might be mixed. Assigning a unique range of VLAN IDs to each customer would restrict customer
configurations, require intensive processing of VLAN mapping tables, and could easily exceed the maximum VLAN limit of
4096.
The Managed Switch supports multiple VLAN tags and can therefore be used in MAN applications as a provider bridge,
aggregating traffic from numerous independent customer LANs into the MAN (Metro Access Network) space. One of the
purposes of the provider bridge is to recognize and use VLAN tags so that the VLANs in the MAN space can be used
independent of the customers’ VLANs. This is accomplished by adding a VLAN tag with a MAN-related VID for frames entering
the MAN. When leaving the MAN, the tag is stripped and the original VLAN tag with the customer-related VID is again available.
This provides a tunneling mechanism to connect remote costumer VLANs through a common MAN space without interfering
with the VLAN tags. All tags use EtherType 0x8100 or 0x88A8, where 0x8100 is used for customer tags and 0x88A8 are used
for service provider tags.
In cases where a given service VLAN only has two member ports on the switch, the learning can be disabled for the particular
VLAN and can therefore rely on flooding as the forwarding mechanism between the two ports. This way, the MAC table
requirements is reduced.
109
Global VLAN Configuration

The Global VLAN Configuration screen in Figure 4-6-1 appears.
Figure 4-6-1 : Global VLAN Configuration Screenshot
Object Description
 Allowed Access This field shows the allowed Access VLANs, it only affects ports configured as
VLANs Access ports. Ports in other modes are members of all VLANs specified in the
Allowed VLANs field.
By default, only VLAN 1 is enabled. More VLANs may be created by using a list
syntax where the individual elements are separated by commas. Ranges are
specified with a dash separating the lower and upper bound.
The following example will create VLANs 1, 10, 11, 12, 13, 200, and 300:
1,10-13,200,300. Spaces are allowed in between the delimiters.
 Ethertype for Custome This field specifies the ethertype/TPID (specified in hexadecimal) used for
S-ports Custom S-ports. The setting is in force for all ports whose Port Type is set to
S-Custom-Port.
Port VLAN Configuration

The VLAN Port Configuration screen in Figure 4-6-2 appears.
Figure 4-6-2 : Port VLAN Configuration Screenshot
110
Object Description
 Port This is the logical port number for this row.
 Mode Access Access ports are normally used to connect to end stations. Dynamic features like
Voice VLAN may add the port to more VLANs behind the scenes. Access ports
have the following characteristics:
 Member of exactly one VLAN, the Port VLAN (Access VLAN), which by
default is 1
 Accepts untagged and C-tagged frames
 Discards all frames that are not classified to the Access VLAN
 On egress all frames classified to the Access VLAN are transmitted

untagged. Other (dynamically added VLANs) are transmitted tagged
Trunk Trunk ports can carry traffic on multiple VLANs simultaneously, and are normally
used to connect to other switches. Trunk ports have the following characteristics:
 By default, a trunk port is member of all VLANs (1-4095)
 The VLANs that a trunk port is member of may be limited by the use of
Allowed VLANs
 Frames classified to a VLAN that the port is not a member of are

discarded
 By default, all frames but frames classified to the Port VLAN (a.k.a.
Native VLAN) get tagged on egress. Frames classified to the Port
VLAN do not get C-tagged on egress
 Egress tagging can be changed to tag all frames, in which case only
tagged frames are accepted on ingress
Hybrid Hybrid ports resemble trunk ports in many ways, but adds additional port
configuration features. In addition to the characteristics described for trunk ports,
hybrid ports have these abilities:
 Can be configured to be VLAN tag unaware, C-tag aware, S-tag

aware, or S-custom-tag aware
 Ingress filtering can be controlled
 Ingress acceptance of frames and configuration of egress tagging can

be configured independently
 Port VLAN Determines the port's VLAN ID (PVID). Allowed VLANs are in the range 1
through 4095, default being 1.
■ On ingress, frames get classified to the Port VLAN if the port is configured as
VLAN unaware, the frame is untagged, or VLAN awareness is enabled on
the port, but the frame is priority tagged (VLAN ID = 0).
■ On egress, frames classified to the Port VLAN do not get tagged if Egress
Tagging configuration is set to untag Port VLAN.
111
The Port VLAN is called an "Access VLAN" for ports in Access mode and Native
VLAN for ports in Trunk or Hybrid mode.
 Port Type Ports in hybrid mode allow for changing the port type, that is, whether a frame's
VLAN tag is used to classify the frame on ingress to a particular VLAN, and if so,
which TPID it reacts on. Likewise, on egress, the Port Type determines the TPID
of the tag, if a tag is required.
■ Unaware:
On ingress, all frames, whether carrying a VLAN tag or not, get classified
to the Port VLAN, and possible tags are not removed on egress.
■ C-Port:
On ingress, frames with a VLAN tag with TPID = 0x8100 get classified to
the VLAN ID embedded in the tag. If a frame is untagged or priority
tagged, the frame gets classified to the Port VLAN. If frames must be
tagged on egress, they will be tagged with a C-tag.
■ S-Port:
On ingress, frames with a VLAN tag with TPID = 0x8100 or 0x88A8 get
classified to the VLAN ID embedded in the tag. If a frame is untagged or
priority tagged, the frame gets classified to the Port VLAN. If frames must
be tagged on egress, they will be tagged with an S-tag.
■ S-Custom-Port:
On ingress, frames with a VLAN tag with a TPID = 0x8100 or equal to the
Ethertype configured for Custom-S ports get classified to the VLAN ID
embedded in the tag. If a frame is untagged or priority tagged, the frame
gets classified to the Port VLAN. If frames must be tagged on egress, they
will be tagged with the custom S-tag.
 Ingress Filtering Hybrid ports allow for changing ingress filtering. Access and Trunk ports always
have ingress filtering enabled.
■ If ingress filtering is enabled (checkbox is checked), frames classified to a

VLAN that the port is not a member of get discarded.
■ If ingress filtering is disabled, frames classified to a VLAN that the port is

not a member of are accepted and forwarded to the switch engine.
However, the port will never transmit frames classified to VLANs that it is not a
member of.
 Ingress Acceptance Hybrid ports allow for changing the type of frames that are accepted on ingress.
■ Tagged and Untagged

Both tagged and untagged frames are accepted.
■ Tagged Only
Only tagged frames are accepted on ingress. Untagged frames are
discarded.
■ Untagged Only
112
Only untagged frames are accepted on ingress. Tagged frames are
discarded.
Egress Tagging This option is only available for ports in Hybrid mode. Ports in Trunk and Hybrid
mode may control the tagging of frames on egress.
■ Untag Port VLAN

Frames classified to the Port VLAN are transmitted untagged. Other
frames are transmitted with the relevant tag.
■ Tag All
All frames, whether classified to the Port VLAN or not, are transmitted
with a tag.
■ Untag All
All frames, whether classified to the Port VLAN or not, are transmitted
without a tag.
 Allowed VLANs Ports in Trunk and Hybrid mode may control which VLANs they are allowed to
become members of. The field's syntax is identical to the syntax used in the
Enabled VLANs field.
By default, a Trunk or Hybrid port will become member of all VLANs, and is
therefore set to 1-4095. The field may be left empty, which means that the port
will not become member of any VLANs.
 Forbidden VLANs A port may be configured to never be member of one or more VLANs. This is
particularly useful when dynamic VLAN protocols like MVRP and GVRP must be
prevented from dynamically adding ports to VLANs. The trick is to mark such
VLANs as forbidden on the port in question. The syntax is identical to the syntax
used in the Enabled VLANs field.
By default, the field is left blank, which means that the port may become a
member of all possible VLANs.
The port must be a member of the same VLAN as the Port VLAN ID.
Buttons
113
4.6.4 VLAN Membership Status
This Page provides an overview of membership status for VLAN users. The VLAN Membership Status screen in Figure 4-6-4
appears.
Figure 4-6-4: VLAN Membership Status for Static User Page Screenshot
Object Description
 VLAN User A VLAN User is a module that uses services of the VLAN management
functionality to configure VLAN memberships and VLAN port configuration such
as PVID, UVID. Currently we support following VLAN :
- Admin : This is reffered as static.
- NAS : NAS provides port-based authentication, which involves

communications between a Supplicant, Authenticator, and an Authentication
Server.
- GVRP : GVRP (GARP VLAN Registration Protocol or Generic VLAN

Registration Protocol) is a protocol that facilitates control of virtual local area
networks (VLANs) within a larger network .
- Voice VLAN : Voice VLAN is a VLAN configured specially for voice traffic
typically originating from IP phones.
- MVR : MVR is used to eliminate the need to duplicate multicast traffic for
subscribers in each VLAN. Multicast traffic for all channels is sent only on a
single (multicast) VLAN.
 Port Members A row of check boxes for each port is displayed for each VLAN ID.
If a port is included in a VLAN, an image will be displayed.
If a port is included in a Forbidden port list, an image will be displayed.

If a port is included in a Forbidden port list and dynamic VLAN user register
VLAN on same Forbidden port, then conflict port will be displayed as conflict port.
 VLAN Membership The VLAN Membership Status Page shall show the current VLAN port members
for all VLANs configured by a selected VLAN User (selection shall be allowed by
a Combo Box). When ALL VLAN Users are selected, it shall show this
information for all the VLAN Users, and this is by default. VLAN membership
114
allows the frames classified to the VLAN ID to be forwarded on the respective
VLAN member ports.
Buttons
: Select VLAN Users from this drop down list.
: Updates the table starting from the first entry in the VLAN Table, i.e. the entry with the lowest VLAN ID.
: Updates the table, starting with the entry after the last entry currently displayed.
4.6.5 VLAN Port Status
This Page provides VLAN Port Staus. The VLAN Port Status screen in Figure 4-6-5 appears.
Figure 4-6-5: VLAN Port Status for Combined users Page Screenshot
Object Description
 Port Type Show the VLAN Awareness for the port.
If VLAN awareness is enabled, the tag is removed from tagged frames received
on the port. VLAN tagged frames are classified to the VLAN ID in the tag.
If VLAN awareness is disabled, all frames are classified to the Port VLAN ID and
115
tags are not removed.
 Ingress Filtering Show the ingress filtering for a port. This parameter affects VLAN ingress
processing. If ingress filtering is enabled and the ingress port is not a member of
the classified VLAN of the frame, the frame is discarded.
 Frame Type Shows whether the port accepts all frames or only tagged frames. This
parameter affects VLAN ingress processing. If the port only accepts tagged
frames, untagged frames received on that port are discarded.
 Port VLAN ID Shows the PVID setting for the port.
 Tx Tag Shows egress filtering frame status whether tagged or untagged.
 Untagged VLAN ID Shows UVID (untagged VLAN ID). Port's UVID determines the packet's behavior
at the egress side.
 Conflicts Shows status of Conflicts whether exists or Not. When a Volatile VLAN User
requests to set VLAN membership or VLAN port configuration, the following
conflicts can occur:
 Functional Conflicts between feature.

 Conflicts due to hardware limitation.
 Direct conflict between user modules.
Buttons
: Select VLAN Users from this drop down list.
116
4.6.6 Port Isolation
Overview
When a VLAN is configured to be a private VLAN, communication between ports within that VLAN can be prevented. Two
application examples are provided in this section:
 Customers connected to an ISP can be members of the same VLAN, but they are not allowed to communicate with each
other within that VLAN.
 Servers in a farm of web servers in a Demilitarized Zone (DMZ) are allowed to communicate with the outside world and
with database servers on the inside segment, but are not allowed to communicate with each other
For private VLANs to be applied, the switch must first be configured for standard VLAN operation When this is in place, one or
more of the configured VLANs can be configured as private VLANs. Ports in a private VLAN fall into one of these two groups:
 Promiscuous ports
— Ports from which traffic can be forwarded to all ports in the private VLAN
— Ports which can receive traffic from all ports in the private VLAN
 Isolated ports
— Ports from which traffic can only be forwarded to promiscuous ports in the private VLAN
— Ports which can receive traffic from only promiscuous ports in the private VLAN
117
The configuration of promiscuous and isolated ports applies to all private VLANs. When traffic comes in on a promiscuous port
in a private VLAN, the VLAN mask from the VLAN table is applied. When traffic comes in on an isolated port, the private VLAN
mask is applied in addition to the VLAN mask from the VLAN table. This reduces the ports to which forwarding can be done to
just the promiscuous ports within the private VLAN.
This Page is used for enabling or disabling port isolation on ports in a Private VLAN. A port member of a VLAN can be isolated
to other isolated ports on the same VLAN and Private VLAN. The Port Isolation screen in Figure 4-6-6 appears.
Figure 4-6-6: Port Isolation Configuration Page Screenshot
Object Description
 Port Members A check box is provided for each port of a private VLAN. When checked, port
isolation is enabled on that port. When unchecked, port isolation is disabled on
that port.
By default, port isolation is disabled on all ports.
Buttons
118
4.6.7 VLAN setting example:
 Separate VLAN
 802.1Q VLAN Trunk
 Port Isolate
4.6.7.1 Two Separate 802.1Q VLANs
The diagram shows how the Managed Switch handle Tagged and Untagged traffic flow for two VLANs. VLAN Group 2 and
VLAN Group 3 are separated VLAN. Each VLAN isolate network traffic so only members of the VLAN receive traffic from the
same VLAN members. The screen in Figure 4-6-7 appears and Table 4-6-8 describes the port configuration of the Managed
Switches.
Figure 4-6-7: Two Separate VLANs Diagram
VLAN Group VID Untagged Members Tagged Members
VLAN Group 1 1 Port-7 ~ Port-52 N/A
VLAN Group 2 2 Port-1,Port-2 Port-3
VLAN Group 3 3 Port-4,Port-5 Port-6
Table 4-1: VLAN and Port Configuration
The scenario is described as follows:
 Untagged packet entering VLAN 2
119
1. While [PC-1] transmit an untagged packet enters Port-1, the Managed Switch will tag it with a VLAN Tag=2.
[PC-2] and [PC-3] will received the packet through Port-2 and Port-3.
2. [PC-4],[PC-5] and [PC-6] received no packet.
3. While the packet leaves Port-2, it will be stripped away it tag becoming an untagged packet.
4. While the packet leaves Port-3, it will keep as a tagged packet with VLAN Tag=2.
 Tagged packet entering VLAN 2
5. While [PC-3] transmit a tagged packet with VLAN Tag=2 enters Port-3, [PC-1] and [PC-2] will received the packet
through Port-1 and Port-2.
6. While the packet leaves Port-1 and Port-2, it will be stripped away it tag becoming an untagged packet.
 Untagged packet entering VLAN 3
1. While [PC-4] transmit an untagged packet enters Port-4, the switch will tag it with a VLAN Tag=3. [PC-5] and
[PC-6] will received the packet through Port-5 and Port-6.
2. While the packet leaves Port-5, it will be stripped away it tag becoming an untagged packet.
3. While the packet leaves Port-6, it will keep as a tagged packet with VLAN Tag=3.
For this example, VLAN Group 1 just set as default VLAN, but only focus on VLAN 2 and VLAN 3
traffic flow
Setup steps
1. Add VLAN Group
Add two VLANs – VLAN 2 and VLAN 3
Type 1-3 in Allowed Access VLANs column, the 1-3 is including VLAN1 and 2 and 3.
Figure 4-6-8: Add VLAN 2 and VLAN 3
2. Assign VLAN Member and PVID for each port:
VLAN 2 : Port-1,Port-2 and Port-3
VLAN 3 : Port-4, Port-5 and Port-6
VLAN 1 : All other ports – Port-7~Port-52
120
Figure 4-6-9: Change Port VLAN of Port 1~3 to be VLAN2 and Port VLAN of Port 4~6 to be VLAN3
3. Enable VLAN Tag for specific ports
Link Type: Port-3 (VLAN-2) and Port-6 (VLAN-3)
Change Port 3 Mode as Trunk, Selects Egress Tagging as Tag All and Types 2 in the Allowed VLANs column.
Change Port 6 Mode as Trunk and Selects Egress Tagging as Tag All and Types 3 in the Allowed VLANs column.
The Per Port VLAN configuration in Figure 4-6-10 appears.
Figure 4-6-10: Check VLAN 2 and 3 Members on VLAN Membership Page
4.6.7.2 VLAN Trunking between two 802.1Q aware switches

The most cases are used for “Uplink” to other switches. VLANs are separated at different switches, but they need to access
with other switches within the same VLAN group. The screen in Figure 4-6-11 appears.
121
Figure 4-6-11: VLAN Trunking Diagram
Setup steps
1. Add VLAN Group
Add two VLANs – VLAN 2 and VLAN 3
Type 1-3 in Allowed Access VLANs column, the 1-3 is including VLAN1 and 2 and 3.
Figure 4-6-12: Add VLAN 2 and VLAN 3
2. Assign VLAN Member and PVID for each port :
VLAN 2 : Port-1,Port-2 and Port-3
VLAN 3 : Port-4, Port-5 and Port-6
VLAN 1 : All other ports – Port-7~Port-52
122
Figure 4-6-13: Changes Port VLAN of Port 1~3 to be VLAN2 and Port VLAN of Port 4~6 to be VLAN3
For the VLAN ports connecting to the hosts, please refer to 4.6.10.1 examples. The following steps will focus on the VLAN
Trunk port configuration.
1. Specify Port-7 to be the 802.1Q VLAN Trunk port.
2. Assign Port-7 to both VLAN 2 and VLAN 3 at the VLAN Member configuration Page.
3. Define a VLAN 1 as a “Public Area” that overlapping with both VLAN 2 members and VLAN 3 members.
4. Assign the VLAN Trunk Port to be the member of each VLAN – which wants to be aggregated. For this example, add Port-7
to be VLAN 2 and VLAN 3 member port.
5. Specify Port-7 to be the 802.1Q VLAN Trunk port, and the Trunking port must be a Tagged port while egress. The Port-7
configuration is shown in Figure 4-6-14.
Figure 4-6-14: VLAN Overlap Port Setting & VLAN 1 – The Public Area Member Assign
That is, although the VLAN 2 members: Port-1 to Port-3 and VLAN 3 members: Port-4 to Port-6 also belongs to VLAN 1. But
with different PVID settings, packets form VLAN 2 or VLAN 3 is not able to access to the other VLAN.
123
6. Repeat Steps 1 to 6, set up the VLAN Trunk port at the partner switch and add more VLANs to join the VLAN trunk, repeat
Steps 1 to 3 to assign the Trunk port to the VLANs.
4.6.7.3 Port Isolate
The diagram shows how the Managed Switch handles isolated and promiscuous ports, and the each PC is not able to access
the isolated port of each other’s PCs. But they all need to access with the same server/AP/Printer. This section will show you
how to configure the port for the server – that could be accessed by each isolated port.
Setup steps
1. Assign Port Mode
Set Port-1~Port-4 in Isolate port.
Set Port5 and Port-6 in Promiscuous port. The screen in Figure 4-6-17 appears.
Figure 4-6-17: The Configuration of Isolated and Promiscuous Port
124
4.6.8 MAC-based VLAN
The MAC-based VLAN enties can be configured here. This Page allows for adding and deleting MAC-based VLAN entries and
assigning the entries to different ports. This Page shows only static entries. The MAC-based VLAN screen in Figure 4-6-18
appears.
Figure 4-6-18: MAC-based VLAN Membership Configuration Page Screenshot
Object Description
 Delete To delete a MAC-based VLAN entry, check this box and press save.
 MAC Address Indicates the MAC address.
 VLAN ID Indicates the VLAN ID.
 Port Members A row of check boxes for each port is displayed for each MAC-based VLAN entry.
To include a port in a MAC-based VLAN, check the box. To remove or exclude
the port from the MAC-based VLAN, make sure the box is unchecked. By default,
no ports are members, and all boxes are unchecked.
 Adding a New Click “Add New Entry” to add a new MAC-based VLAN entry. An empty row is
MAC-based VLAN added to the table, and the MAC-based VLAN entry can be configured as
needed. Any unicast MAC address can be configured for the MAC-based VLAN
entry. No broadcast or multicast MAC addresses are allowed. Legal values for a
VLAN ID are 1 through 4095.
The MAC-based VLAN entry is enabled when you click on "Save". A MAC-based
VLAN without any port members will be deleted when you click "Save".
The “Delete” button can be used to undo the addition of new MAC-based VLANs.
Buttons
: Click to add a new MAC-based VLAN entry.
125
: Updates the table starting from the first entry in the MAC-based VLAN Table.
4.6.9 MAC-based VLAN Status
This Page shows MAC-based VLAN entries configured by various MAC-based VLAN users. The MAC-based VLAN Status
Figure 4-6-19: MAC-based VLAN Membership Configuration for User Static Page Screenshot
Object Description
 MAC Address Indicates the MAC address.
 VLAN ID Indicates the VLAN ID.
 Port Members Port members of the MAC-based VLAN entry.
Buttons
4.6.10 Protocol-based VLAN
This Page allows you to add new protocols to Group Name (unique for each Group) mapping entries as well as allow you to see
and delete already mapped entries for the switch. The Protocol-based VLAN screen in Figure 4-6-20 appears.
126
Figure 4-6-20: Protocol to Group Mapping Table Page Screenshot
Object Description
 Delete To delete a Protocol to Group Name map entry, check this box. The entry will be
deleted on the switch during the next Save.
 Frame Type Frame Type can have one of the following values:
1. Ethernet
2. LLC
3. SNAP
Note: On changing the Frame type field, valid value of the following text field will
vary depending on the new frame type you selected.
 Value Valid value that can be entered in this text field depends on the option selected
from the the preceding Frame Type selection menu.
Below is the criteria for three different Frame Types:
1. For Ethernet: Values in the text field when Ethernet is selected as a

Frame Type is called etype. Valid values for etype ranges from
0x0600-0xffff
2. For LLC: Valid value in this case is comprised of two different

sub-values.
a. DSAP: 1-byte long string (0x00-0xff)
b. SSAP: 1-byte long string (0x00-0xff)
3. For SNAP: Valid value in this case also is comprised of two different
sub-values.
a. OUI: OUI (Organizationally Unique Identifier) is value in format of

xx-xx-xx where each pair (xx) in string is a hexadecimal value
ranges from 0x00-0xff.
b. PID: If the OUI is hexadecimal 000000, the protocol ID is the

Ethernet type (EtherType) field value for the protocol running on top
127
of SNAP; if the OUI is an OUI for a particular organization, the
protocol ID is a value assigned by that organization to the protocol
running on top of SNAP.
In other words, if value of OUI field is 00-00-00 then value of PID will be
etype (0x0600-0xffff) and if value of OUI is other than 00-00-00 then valid
value of PID will be any value from 0x0000 to 0xffff.
 Group Name A valid Group Name is a unique 16-character long string for every entry which
consists of a combination of alphabets (a-z or A-Z) and integers(0-9).
Note: special character and underscore(_) are not allowed.
 Adding a New Group to Click “Add New Entry”to add a new entry in mapping table. An empty row is
VLAN mapping entry added to the table; Frame Type, Value and the Group Name can be configured
as needed.
The “Delete” button can be used to undo the addition of new entry.
Buttons
: Click to add a new entry in mapping table.
4.6.11 Protocol-based VLAN Membership

This Page allows you to map a already configured Group Name to a VLAN for the switch. The Group Name to VLAN Mapping
Table screen in Figure 4-6-21 appears.
Figure 4-6-21: Group Name to VLAN Mapping Table Page Screenshot
Object Description
128
 Delete To delete a Group Name to VLAN map entry, check this box. The entry will be
deleted on the switch during the next Save
 Group Name A valid Group Name is a string of atmost 16 characters which consists of a
combination of alphabets (a-z or A-Z) and integers(0-9), no special character is
allowed. Whichever Group name you try map to a VLAN must be present in
Protocol to Group mapping table and must not be preused by any other existing
mapping entry on this Page.
 VLAN ID Indicates the ID to which Group Name will be mapped. A valid VLAN ID ranges
from 1-4095.
 Port Members A row of check boxes for each port is displayed for each Group Name to VLAN ID
mapping. To include a port in a mapping, check the box. To remove or exclude
the port from the mapping, make sure the box is unchecked. By default, no ports
are members, and all boxes are unchecked.
 Adding a New Group to Click “Add New Entry” to add a new entry in mapping table. An empty row is
VLAN mapping entry added to the table, the Group Name, VLAN ID and port members can be
configured as needed. Legal values for a VLAN ID are 1 through 4095.
The “Delete” button can be used to undo the addition of new entry.
Buttons
129
4.7 Spanning Tree Protocol
4.7.1 Theory
The Spanning Tree protocol can be used to detect and disable network loops, and to provide backup links between switches,
bridges or routers. This allows the switch to interact with other bridging devices in your network to ensure that only one route
exists between any two stations on the network, and provide backup links which automatically take over when a primary link
goes down. The spanning tree algorithms supported by this switch include these versions:
 STP – Spanning Tree Protocol (IEEE 802.1D)
 RSTP – Rapid Spanning Tree Protocol (IEEE 802.1w)
 MSTP – Multiple Spanning Tree Protocol (IEEE 802.1s)
The IEEE 802.1D Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol allow for the blocking of links
between switches that form loops within the network. When multiple links between switches are detected, a primary link is
established. Duplicated links are blocked from use and become standby links. The protocol allows for the duplicate links to be
used in the event of a failure of the primary link. Once the Spanning Tree Protocol is configured and enabled, primary links are
established and duplicated links are blocked automatically. The reactivation of the blocked links (at the time of a primary link
failure) is also accomplished automatically without operator intervention.
This automatic network reconfiguration provides maximum uptime to network users. However, the concepts of the Spanning
Tree Algorithm and protocol are a complicated and complex subject and must be fully researched and understood. It is possible
to cause serious degradation of the performance of the network if the Spanning Tree is incorrectly configured. Please read the
following before making any changes from the default values.
The Switch STP performs the following functions:
 Creates a single spanning tree from any combination of switching or bridging elements.
 Creates multiple spanning trees – from any combination of ports contained within a single switch, in user specified
groups.
 Automatically reconfigures the spanning tree to compensate for the failure, addition, or removal of any element in
the tree.
 Reconfigures the spanning tree without operator intervention.
Bridge Protocol Data Units

For STP to arrive at a stable network topology, the following information is used:
 The unique switch identifier
 The path cost to the root associated with each switch port
 The port identifier
STP communicates between switches on the network using Bridge Protocol Data Units (BPDUs). Each BPDU contains the
following information:
 The unique identifier of the switch that the transmitting switch currently believes is the root switch
130
 The path cost to the root from the transmitting port
 The port identifier of the transmitting port
The switch sends BPDUs to communicate and construct the spanning-tree topology. All switches connected to the LAN on
which the packet is transmitted will receive the BPDU. BPDUs are not directly forwarded by the switch, but the receiving switch
uses the information in the frame to calculate a BPDU, and, if the topology changes, initiates a BPDU transmission.
The communication between switches via BPDUs results in the following:
 One switch is elected as the root switch
 The shortest distance to the root switch is calculated for each switch
 A designated switch is selected. This is the switch closest to the root switch through which packets will be forwarded
to the root.
 A port for each switch is selected. This is the port providing the best path from the switch to the root switch.
 Ports included in the STP are selected.
Creating a Stable STP Topology

It is to make the root port a fastest link. If all switches have STP enabled with default settings, the switch with the lowest MAC
address in the network will become the root switch. By increasing the priority (lowering the priority number) of the best switch,
STP can be forced to select the best switch as the root switch.
When STP is enabled using the default parameters, the path between source and destination stations in a switched network
might not be ideal. For instance, connecting higher-speed links to a port that has a higher number than the current root port can
cause a root-port change.
STP Port States

The BPDUs take some time to pass through a network. This propagation delay can result in topology changes where a port that
transitioned directly from a Blocking state to a Forwarding state could create temporary data loops. Ports must wait for new
network topology information to propagate throughout the network before starting to forward packets. They must also wait for
the packet lifetime to expire for BPDU packets that were forwarded based on the old topology. The forward delay timer is used to
allow the network topology to stabilize after a topology change. In addition, STP specifies a series of states a port must
transition through to further ensure that a stable network topology is created after a topology change.
Each port on a switch using STP exists is in one of the following five states:
 Blocking – the port is blocked from forwarding or receiving packets
 Listening – the port is waiting to receive BPDU packets that may tell the port to go back to the blocking state
 Learning – the port is adding addresses to its forwarding database, but not yet forwarding packets
 Forwarding – the port is forwarding packets
 Disabled – the port only responds to network management messages and must return to the blocking state first
A port transitions from one state to another as follows:

 From initialization (switch boot) to blocking
 From blocking to listening or to disabled
 From listening to learning or to disabled
 From learning to forwarding or to disabled
131
 From forwarding to disabled
 From disabled to blocking
Figure 4-7-1: STP Port State Transitions
You can modify each port state by using management software. When you enable STP, every port on every switch in the
network goes through the blocking state and then transitions through the states of listening and learning at power up. If properly
configured, each port stabilizes to the forwarding or blocking state. No packets (except BPDUs) are forwarded from, or received
by, STP enabled ports until the forwarding state is enabled for that port.
2. STP Parameters
STP Operation Levels

The Switch allows for two levels of operation: the switch level and the port level. The switch level forms a spanning tree
consisting of links between one or more switches. The port level constructs a spanning tree consisting of groups of one or more
ports. The STP operates in much the same way for both levels.
On the switch level, STP calculates the Bridge Identifier for each switch and then sets the Root
Bridge and the Designated Bridges.
On the port level, STP sets the Root Port and the Designated Ports.
132
The following are the user-configurable STP parameters for the switch level:
Parameter Description Default Value
Bridge Identifier(Not user A combination of the User-set priority and 32768 + MAC
configurable the switch’s MAC address.
except by setting priority The Bridge Identifier consists of two parts:
below) a 16-bit priority and a 48-bit Ethernet MAC
address 32768 + MAC
Priority A relative priority for each switch – lower 32768
numbers give a higher priority and a greater
chance of a given switch being elected as
the root bridge
Hello Time The length of time between broadcasts of 2 seconds
the hello message by the switch
Maximum Age Timer Measures the age of a received BPDU for a 20 seconds
port and ensures that the BPDU is discarded
when its age exceeds the value of the
maximum age timer.
Forward Delay Timer The amount time spent by a port in the 15 seconds
learning and listening states waiting for a
BPDU that may return the port to the
blocking state.
The following are the user-configurable STP parameters for the port or port group level:
Variable Description Default Value
Port Priority A relative priority for each 128
port –lower numbers give a higher priority
and a greater chance of a given port being
elected as the root port
Port Cost A value used by STP to evaluate paths – 200,000-100Mbps Fast Ethernet ports
STP calculates path costs and selects the 20,000-1000Mbps Gigabit Ethernet
path with the minimum cost as the active ports
path 0 - Auto
Default Spanning-Tree Configuration
Feature Default Value
Enable state STP disabled for all ports
Port priority 128
Port cost 0
Bridge Priority 32,768
133
User-Changeable STA Parameters

The Switch’s factory default setting should cover the majority of installations. However, it is advisable to keep the default settings
as set at the factory; unless, it is absolutely necessary. The user changeable parameters in the Switch are as follows:
Priority – A Priority for the switch can be set from 0 to 65535. 0 is equal to the highest Priority.
Hello Time – The Hello Time can be from 1 to 10 seconds. This is the interval between two transmissions of BPDU packets sent
by the Root Bridge to tell all other Switches that it is indeed the Root Bridge. If you set a Hello Time for your Switch, and it is not
the Root Bridge, the set Hello Time will be used if and when your Switch becomes the Root Bridge.
The Hello Time cannot be longer than the Max. Age; otherwise, a configuration error will
occur.
Max. Age – The Max Age can be from 6 to 40 seconds. At the end of the Max Age, if a BPDU has still not been received from
the Root Bridge, your Switch will start sending its own BPDU to all other Switches for permission to become the Root Bridge. If it
turns out that your Switch has the lowest Bridge Identifier, it will become the Root Bridge.
Forward Delay Timer – The Forward Delay can be from 4 to 30 seconds. This is the time any port on the
Switch spends in the listening state while moving from the blocking state to the forwarding state.
Observe the following formulas when setting the above parameters:
Max. Age _ 2 x (Forward Delay - 1 second)
Max. Age _ 2 x (Hello Time + 1 second)
Port Priority – A Port Priority can be from 0 to 240. The lower the number, the greater the probability the port will be chosen as
the Root Port.
Port Cost – A Port Cost can be set from 0 to 200000000. The lower the number, the greater the probability the port will be
chosen to forward packets.
3. Illustration of STP
A simple illustration of three switches connected in a loop is depicted in the below diagram. In this example, you can anticipate
some major network problems if the STP assistance is not applied.
If switch A broadcasts a packet to switch B, switch B will broadcast it to switch C, and switch C will broadcast it to back to switch
A and so on. The broadcast packet will be passed indefinitely in a loop, potentially causing a network failure. In this example,
STP breaks the loop by blocking the connection between switch B and C. The decision to block a particular connection is based
on the STP calculation of the most current Bridge and Port settings.
Now, if switch A broadcasts a packet to switch C, then switch C will drop the packet at port 2 and the broadcast will end there.
Setting-up STP using values other than the defaults, can be complex. Therefore, you are advised to keep the default factory
settings and STP will automatically assign root bridges/ports and block loop connections. Influencing STP to choose a particular
switch as the root bridge using the Priority setting, or influencing STP to choose a particular port to block using the Port Priority
and Port Cost settings is, however, relatively straight forward.
134
Figure 4-7-2: Before Applying the STA Rules
In this example, only the default STP values are used.
Figure 4-7-3: After Applying the STA Rules
135
The switch with the lowest Bridge ID (switch C) was elected the root bridge, and the ports were selected to give a high port cost
between switches B and C. The two (optional) Gigabit ports (default port cost = 20,000) on switch A are connected to one
(optional) Gigabit port on both switch B and C. The redundant link between switch B and C is deliberately chosen as a 100 Mbps
Fast Ethernet link (default port cost = 200,000). Gigabit ports could be used, but the port cost should be increased from the
default to ensure that the link between switch B and switch C is the blocked link.
4.7.2 STP System Configuration
This Page allows you to configure STP system settings. The settings are used by all STP Bridge instances in the Switch. The
Managed Switch support the following Spanning Tree protocols:
‧ Compatiable -- Spanning Tree Protocol (STP):Provides a single path between end stations, avoiding and
eliminating loops.
‧ Normal -- Rapid Spanning Tree Protocol (RSTP) : Detects and uses of network topologies that provide faster
spanning tree convergence, without creating forwarding loops.
‧ Extension – Multiple Spanning Tree Protocol (MSTP) : Defines an extension to RSTP to further develop the
usefulness of virtual LANs (VLANs). This "Per-VLAN" Multiple Spanning Tree Protocol configures a separate
Spanning Tree for each VLAN group and blocks all but one of the possible alternate paths within each Spanning
Tree.
The STP System Configuration screen in Figure 4-7-4 appears.
Figure 4-7-4: STP Bridge Configuration Page Screenshot
136
Basic Settings
Object Description
 Protocol Version The STP protocol version setting. Valid values are:
 STP (IEEE 802.1D Spanning Tree Protocol)

 RSTP (IEEE 802.2w Rapid Spanning Tree Protocol)
 MSTP (IEEE 802.1s Multiple Spanning Tree Protocol)
 Bridge Priority Controls the bridge priority. Lower numeric values have better priority. The bridge
priority plus the MSTI instance number, concatenated with the 6-byte MAC
address of the switch forms a Bridge Identifier.
For MSTP operation, this is the priority of the CIST. Otherwise, this is the priority
of the STP/RSTP bridge.
 Forward Delay The delay used by STP Bridges to transition Root and Designated Ports to
Forwarding (used in STP compatible mode). Valid values are in the range 4 to 30
seconds
-Default: 15
-Minimum: The higher of 4 or [(Max. Message Age / 2) + 1]
-Maximum: 30
 Max Age The maximum age of the information transmitted by the Bridge when it is the
Root Bridge. Valid values are in the range 6 to 40 seconds.
-Default: 20
-Minimum: The higher of 6 or [2 x (Hello Time + 1)].
-Maximum: The lower of 40 or [2 x (Forward Delay -1)]
 Maximum Hop Count This defines the initial value of remaining Hops for MSTI information generated at
the boundary of an MSTI region. It defines how many bridges a root bridge can
distribute its BPDU information. Valid values are in the range 6 to 40 hops.
 Transmit Hold Count The number of BPDU's a bridge port can send per second. When exceeded,
transmission of the next BPDU will be delayed. Valid values are in the range 1 to
10 BPDU's per second.
Advanced Settings
Object Description
 Edge Port BPDU Control whether a port explicitly configured as Edge will transmit and receive
Filtering BPDUs.
 Edge Port BPDU Guard Control whether a port explicitly configured as Edge will disable itself upon
reception of a BPDU. The port will enter the error-disabled state, and will be
removed from the active topology.
137
 Port Error Recovery Control whether a port in the error-disabled state automatically will be enabled
after a certain time. If recovery is not enabled, ports have to be disabled and
re-enabled for normal STP operation. The condition is also cleared by a system
reboot.
 Port Error Recovery The time that has to pass before a port in the error-disabled state can be
Timeout enabled. Valid values are between 30 and 86400 seconds (24 hours).
The Managed Switch implements the Rapid Spanning Protocol as the default spanning tree
protocol. When selecting “Compatibles” mode, the system uses the RSTP (802.1w) to be
compatible and to co-work with another STP (802.1D)’s BPDU control packet.
Buttons
4.7.3 Bridge Status
This Page provides a status overview for all STP bridge instances. The displayed table contains a row for each STP bridge
instance, where the column displays the following information: The Bridge Status screen in Figure 4-7-5 appears.
Figure 4-7-5: STP Bridge Status Page Screenshot
Object Description
 MSTI The Bridge Instance. This is also a link to the STP Detailed Bridge Status.
 Bridge ID The Bridge ID of this Bridge instance.
 Root ID The Bridge ID of the currently elected root bridge.
 Root Port The switch port currently assigned the root port role.
 Root Cost Root Path Cost. For the Root Bridge this is zero. For all other Bridges, it is the
sum of the Port Path Costs on the least cost path to the Root Bridge.
138
 Topology Flag The current state of the Topology Change Flag for this Bridge instance.
 Topology Change Last The time since last Topology Change occurred.
Buttons
4.7.4 CIST Port Configuration
This Page allows the user to inspect the current STP CIST port configurations, and possibly change them as well. The CIST
Port Configuration screen in Figure 4-7-6 appears.
Figure 4-7-6 : STP CIST Port Configuration Page Screenshot
Object Description
 Port The switch port number of the logical STP port.
 STP Enabled Controls whether RSTP is enabled on this switch port.
139
 Path Cost Controls the path cost incurred by the port. The Auto setting will set the path cost
as appropriate by the physical link speed, using the 802.1D recommended
values. Using the Specific setting, a user-defined value can be entered. The
path cost is used when establishing the active topology of the network. Lower
path cost ports are chosen as forwarding ports in favor of higher path cost ports.
Valid values are in the range 1 to 200000000.
 Priority Controls the port priority. This can be used to control priority of ports having
identical port cost. (See above).
Default: 128
Range: 0-240, in steps of 16
 AdminEdge Controls whether the operEdge flag should start as beeing set or cleared. (The
initial operEdge state when a port is initialized).
 AutoEdge Controls whether the bridge should enable automatic edge detection on the
bridge port. This allows operEdge to be derived from whether BPDU's are
received on the port or not.
 Restricted Role If enabled, causes the port not to be selected as Root Port for the CIST or any
MSTI, even if it has the best spanning tree priority vector. Such a port will be
selected as an Alternate Port after the Root Port has been selected. If set, it can
cause lack of spanning tree connectivity. It can be set by a network administrator
to prevent bridges external to a core region of the network influence the spanning
tree active topology, possibly because those bridges are not under the full control
of the administrator. This feature is also known as Root Guard.
 Restricted TCN If enabled, causes the port not to propagate received topology change
notifications and topology changes to other ports. If set it can cause temporary
loss of connectivity after changes in a spanning tree's active topology as a result
of persistently incorrect learned station location information. It is set by a network
administrator to prevent bridges external to a core region of the network, causing
address flushing in that region, possibly because those bridges are not under the
full control of the administrator or the physical link state of the attached LANs
transits frequently.
 BPDU Guard If enabled, causes the port to disable itself upon receiving valid BPDU's. Contrary
to the similar bridge setting, the port Edge status does not effect this setting.
A port entering error-disabled state due to this setting is subject to the bridge Port
Error Recovery setting as well.
 Point-to-point Controls whether the port connects to a point-to-point LAN rather than a shared
medium. This can be automatically determined, or forced either true or false.
Transitions to the forwarding state is faster for point-to-point LANs than for
shared media.
140
Buttons
By default, the system automatically detects the speed and duplex mode used on each port, and configures the path cost
according to the values shown below. Path cost “0” is used to indicate auto-configuration mode. When the short path cost
method is selected and the default path cost recommended by the IEEE 8021w standard exceeds 65,535, the default is set to
65,535.
Port Type IEEE 802.1D-1998 IEEE 802.1w-2001
Ethernet 50-600 200,000-20,000,000
Fast Ethernet 10-60 20,000-2,000,000
Gigabit Ethernet 3-10 2,000-200,000
Table 4-7-1: Recommended STP Path Cost Range
Port Type Link Type IEEE 802.1D-1998 IEEE 802.1w-2001
Ethernet Half Duplex 100 2,000,000

Full Duplex 95 1,999,999
Trunk 90 1,000,000
Fast Ethernet Half Duplex 19 200,000
Full Duplex 18 100,000
Trunk 15 50,000
Gigabit Ethernet Full Duplex 4 10,000
Trunk 3 5,000
Table 4-7-2: Recommended STP Path Costs
Port Type Link Type IEEE 802.1w-2001

Ethernet Half Duplex 2,000,000
Full Duplex 1,000,000
Trunk 500,000
Fast Ethernet Half Duplex 200,000
Full Duplex 100,000
Trunk 50,000
Gigabit Ethernet Full Duplex 10,000
Trunk 5,000
Table 4-7-3: Default STP Path Costs
141
4.7.5 MSTI Priorities
This Page allows the user to inspect the current STP MSTI bridge instance priority configurations, and possibly change them as
well. The MSTI Priority screen in Figure 4-7-7 appears.
Figure 4-7-7: MSTI Priority Page Screenshot
Object Description
 MSTI The bridge instance. The CIST is the default instance, which is always active.
 Priority Controls the bridge priority. Lower numerical values have better priority. The
bridge priority plus the MSTI instance number, concatenated with the 6-byte MAC
address of the switch forms a Bridge Identifier.
Buttons
142
4.7.6 MSTI Configuration
This Page allows the user to inspect the current STP MSTI bridge instance priority configurations, and possibly change them as
well. The MSTI Configuration screen in Figure 4-7-8 appears.
Figure 4-7-8: MSTI Configuration Page Screenshot
Configuration Identification
Object Description
 Configuration Name The name identifiying the VLAN to MSTI mapping. Bridges must share the name
and revision (see below), as well as the VLAN-to-MSTI mapping configuration in
order to share spanning trees for MSTI's. (Intra-region). The name is at most 32
characters.
 Configuration Revision The revision of the MSTI configuration named above. This must be an integer
between 0 and 65535.
143
MSTI Mapping
Object Description
 MSTI The bridge instance. The CIST is not available for explicit mapping, as it will
receive the VLANs not explicitly mapped.
 VLANs Mapped The list of VLAN's mapped to the MSTI. The VLANs must be separated with
comma and/or space. A VLAN can only be mapped to one MSTI. A unused MSTI
should just be left empty. (I.e. not having any VLANs mapped to it.)
Buttons
4.7.7 MSTI Ports Configuration
This Page allows the user to inspect the current STP MSTI port configurations, and possibly change them as well. A MSTI port
is a virtual port, which is instantiated separately for each active CIST (physical) port for each MSTI instance configured and
applicable for the port. The MSTI instance must be selected before displaying actual MSTI port configuration options.
This Page contains MSTI port settings for physical and aggregated ports. The aggregation settings are global. The MSTI Port
Configuration screen in Figure 4-7-9 & Figure 4-7-10 appears.
Figure 4-7-9 : MSTI Port Configuration Page Screenshot
MSTI Port Configuration
Object Description
 Select MSTI Select the bridge instance and set more detail configuration.
144
Figure 4-7-10 : MST1 MSTI Port Configuration Page Screenshot
MSTx MSTI Port Configuration
Object Description
 Port The switch port number of the corresponding STP CIST (and MSTI) port.
 Path Cost Controls the path cost incurred by the port. The Auto setting will set the path cost
as appropriate by the physical link speed, using the 802.1D recommended
values. Using the Specific setting, a user-defined value can be entered. The path
cost is used when establishing the active topology of the network. Lower path
cost ports are chosen as forwarding ports in favor of higher path cost ports. Valid
values are in the range 1 to 200000000.
 Priority Controls the port priority. This can be used to control priority of ports having
identical port cost.
Buttons
: Click to set MSTx configuration
145
4.7.8 Port Status
This Page displays the STP CIST port status for port physical ports in the currently selected switch.
The STP Port Status screen in Figure 4-7-11 appears.
Figure 4-7-11: STP Port Status Page Screenshot
Object Description
 Port The switch port number of the logical STP port.
 CIST Role The current STP port role of the ICST port. The port role can be one of the
following values:
■ AlternatePort
■ BackupPort
■ RootPort
■ DesignatedPort
■ Disable
 CIST State The current STP port state of the CIST port . The port state can be one of the
following values:
■ Disabled
■ Learning
■ Forwarding
 Uptime The time since the bridge port was last initialized.
Buttons
Auto-refresh : Check this box to refresh the Page automatically. Automatic refresh occurs every 3 seconds
146
4.7.9 Port Statistics
This Page displays the STP port statistics counters for port physical ports in the currently selected switch.
The STP Port Statistics screen in Figure 4-7-12 appears.
Figure 4-7-12: STP Statistics Page Screenshot
Object Description
 Port The switch port number of the logical RSTP port.
 MSTP The number of MSTP Configuration BPDU's received/transmitted on the port.
 RSTP The number of RSTP Configuration BPDU's received/transmitted on the port.
 STP The number of legacy STP Configuration BPDU's received/transmitted on the
port.
 TCN The number of (legacy) Topology Change Notification BPDU's
received/transmitted on the port.
 Discarded Unknown The number of unknown Spanning Tree BPDU's received (and discarded) on the
port.
 Discarded Illegal The number of illegal Spanning Tree BPDU's received (and discarded) on the
port.
Buttons
147
4.8 Multicast
4.8.1 IGMP Snooping
The Internet Group Management Protocol (IGMP) lets host and routers share information about multicast groups
memberships. IGMP snooping is a switch feature that monitors the exchange of IGMP messages and copies them to the CPU
for feature processing. The overall purpose of IGMP Snooping is to limit the forwarding of multicast frames to only ports that are
a member of the multicast group.
About the Internet Group Management Protocol (IGMP) Snooping
Computers and network devices that want to receive multicast transmissions need to inform nearby routers that they will
become members of a multicast group. The Internet Group Management Protocol (IGMP) is used to communicate this
information. IGMP is also used to periodically check the multicast group for members that are no longer active. In the case
where there is more than one multicast router on a sub network, one router is elected as the ‘queried’. This router then keeps
track of the membership of the multicast groups that have active members. The information received from IGMP is then used to
determine if multicast packets should be forwarded to a given sub network or not. The router can check, using IGMP, to see if
there is at least one member of a multicast group on a given subnet work. If there are no members on a sub network, packets
will not be forwarded to that sub network.
Figure 4-8-1: Multicast Service
148
Figure 4-8-2: Multicast Flooding
Figure 4-8-3: IGMP Snooping Multicast Stream Control
149
IGMP Versions 1 and 2

Multicast groups allow members to join or leave at any time. IGMP provides the method for members and multicast routers to
communicate when joining or leaving a multicast group. IGMP version 1 is defined in RFC 1112. It has a fixed packet size and
no optional data. The format of an IGMP packet is shown below:
IGMP Message Format
Octets
0 8 16 31
Type Response Time Checksum
Group Address (all zeros if this is a query)
The IGMP Type codes are shown below:
Type Meaning
0x11 Membership Query (if Group Address is 0.0.0.0)
Specific Group Membership Query (if Group Address is

0x11
Present)
0x16 Membership Report (version 2)
0x17 Leave a Group (version 2)
0x12 Membership Report (version 1)
IGMP packets enable multicast routers to keep track of the membership of multicast groups, on their respective sub networks.
The following outlines what is communicated between a multicast router and a multicast group member using IGMP.
A host sends an IGMP “report” to join a group
A host will never send a report when it wants to leave a group (for version 1).
A host will send a “leave” report when it wants to leave a group (for version 2).
Multicast routers send IGMP queries (to the all-hosts group address: 224.0.0.1) periodically to see whether any group members
exist on their sub networks. If there is no response from a particular group, the router assumes that there are no group members
on the network.
The Time-to-Live (TTL) field of query messages is set to 1 so that the queries will not be forwarded to other sub networks.
IGMP version 2 introduces some enhancements such as a method to elect a multicast queried for each LAN, an explicit leave
message, and query messages that are specific to a given group.
150
The states a computer will go through to join or to leave a multicast group are shown below:
Figure 4-8-4: IGMP State Transitions
 IGMP Querier –
A router, or multicast-enabled switch, can periodically ask their hosts if they want to receive multicast traffic. If there is more
than one router/switch on the LAN performing IP multicasting, one of these devices is elected “querier” and assumes the
role of querying the LAN for group members. It then propagates the service requests on to any upstream multicast
switch/router to ensure that it will continue to receive the multicast service.
Multicast routers use this information, along with a multicast routing protocol such as
DVMRP or PIM, to support IP multicasting across the Internet.
151
4.8.2 Profile Table
This page provides IPMC Profile related configurations. The IPMC profile is used to deploy the access control on IP multicast
streams. It is allowed to create at maximum 64 Profiles with at maximum 128 corresponding rules for each. The Profile Table
Figure 4-8-5: IPMC Profile Configuration Page
Object Description
 Global Profile Mode Enable/Disable the Global IPMC Profile.
System starts to do filtering based on profile settings only when the global profile
mode is enabled.
 Delete Check to delete the entry.
The designated entry will be deleted during the next save.
 Profile Name The name used for indexing the profile table.
Each entry has the unique name which is composed of at maximum 16
alphabetic and numeric characters. At least one alphabet must be present.
 Profile Description Additional description, which is composed of at maximum 64 alphabetic and
numeric characters, about the profile.
No blank or space characters are permitted as part of description. Use "_" or "-"
to separate the description sentence.
 Rule When the profile is created, click the edit button to enter the rule setting page of
the designated profile. Summary about the designated profile will be shown by
clicking the view button. You can manage or inspect the rules of the designated
profile by using the following buttons:
: List the rules associated with the designated profile.
: Adjust the rules associated with the designated profile.
152
Buttons
: Click to add new IPMC profile. Specify the name and configure the new entry. Click "Save”.
4.8.3 Address Entry
This page provides address range settings used in IPMC profile. The address entry is used to specify the address
range that will be associated with IPMC Profile. It is allowed to create at maximum 128 address entries in the
system. The Profile Table screen in Figure 4-8-6 appears.
Figure 4-8-6: IPMC Profile Address Configuration Page
Object Description
 Delete Check to delete the entry.
The designated entry will be deleted during the next save.
 Entry Name The name used for indexing the address entry table.
Each entry has the unique name which is composed of at maximum 16
alphabetic and numeric characters. At least one alphabet must be present.
 Start Address The starting IPv4/IPv6 Multicast Group Address that will be used as an address
range.
 End Address The ending IPv4/IPv6 Multicast Group Address that will be used as an address
range.
Buttons
: Click to add new address range. Specify the name and configure the
addresses. Click "Save”.
153
: Refreshes the displayed table starting from the input fields.
: Updates the table starting from the first entry in the IPMC Profile Address Configuration.
4.8.4 IGMP Snooping Configuration
This Page provides IGMP Snooping related configuration. The IGMP Snooping Configuration screen in Figure 4-8-7 appears.
Figure 4-8-7: IGMP Snooping Configuration Page Screenshot
Object Description
 Snooping Enabled Enable the Global IGMP Snooping.
 Unregistered IPMCv4 Enable unregistered IPMCv4 traffic flooding.
Flooding Enabled The flooding control takes effect only when IGMP Snooping is enabled.
When IGMP Snooping is disabled, unregistered IPMCv4 traffic flooding is always
154
active in spite of this setting.
 IGMP SSM Range SSM (Source-Specific Multicast) Range allows the SSM-aware hosts and routers
run the SSM service model for the groups in the address range.
 Leave Proxy Enable Enable IGMP Leave Proxy. This feature can be used to avoid forwarding
unnecessary leave messages to the router side.
 Proxy Enable Enable IGMP Proxy. This feature can be used to avoid forwarding unnecessary
join and leave messages to the router side.
 Router Port Specify which ports act as IGMP router ports. A router port is a port on the
Ethernet switch that leads towards the Layer 3 multicast device or IGMP querier.
The Switch forwards IGMP join or leave packets to an IGMP router port.
 Auto:
Select “Auto” to have the Managed Switch automatically uses the port
as IGMP Router port if the port receives IGMP query packets.
 Fix:
The Managed Switch always uses the specified port as an IGMP
Router port. Use this mode when you connect an IGMP multicast
server or IP camera which applied with multicast protocol to the port.
 None:
The Managed Switch will not use the specified port as an IGMP
Router port. The Managed Switch will not keep any record of an
IGMP router being connected to this port. Use this mode when you
connect other IGMP multicast servers directly on the non-querier
Managed Switch and don’t want the multicast stream be flood to
uplink switch throught the port that connected to the IGMP querier.
 Fast Leave Enable the fast leave on the port.
 Throtting Enable to limit the number of multicast groups to which a switch port can belong.
Buttons
155
4.8.5 IGMP Snooping VLAN Configuration
Each Page shows up to 99 entries from the VLAN table, default being 20, selected through the "entries per Page" input field.
When first visited, the web Page will show the first 20 entries from the beginning of the VLAN Table. The first displayed will be
the one with the lowest VLAN ID found in the VLAN Table.
The "VLAN" input fields allow the user to select the starting point in the VLAN Table. The IGMP Snooping VLAN Configuration
Figure 4-8-8: IGMP Snooping VLAN Configuration Page Screenshot
Object Description
 Delete Check to delete the entry. The designated entry will be deleted during the next
save.
 VLAN ID The VLAN ID of the entry.
 IGMP Snooping Enable Enable the per-VLAN IGMP Snooping. Only up to 32 VLANs can be selected.
 Querier Election Enable the IGMP Querier election in the VLAN. Disable to act as an IGMP
Non-Querier.
 Querier Address Define the IPv4 address as source address used in IP header for IGMP Querier
election.
■ When the Querier address is not set, system uses IPv4 management
address of the IP interface associated with this VLAN.
■ When the IPv4 management address is not set, system uses the first
available IPv4 management address. Otherwise, system uses a
pre-defined value.
By default, this value will be 192.0.2.1
 Compatibility Compatibility is maintained by hosts and routers taking appropriate actions
depending on the versions of IGMP operating on hosts and routers within a
network. The allowed selection is IGMP-Auto, Forced IGMPv1, Forced
IGMPv2, Forced IGMPv3.
Default compatibility value is IGMP-Auto.
156
 PRI (PRI) Priority of Interface. It indicates the IGMP control frame priority level
generated by the system. These values can be used to prioritize different classes
of traffic.
The allowed range is 0 (best effort) to 7 (highest), default interface priority value
is 0
 RV Robustness Variable. The Robustness Variable allows tuning for the expected
packet loss on a network.
The allowed range is 1 to 255, default robustness variable value is 2.
 QI Query Interval. The Query Interval is the interval between General Queries sent
by the Querier. The allowed range is 1 to 31744 seconds, default query interval is
125 seconds.
 QRI Query Response Interval. The Max Response Time used to calculate the Max
Resp Code inserted into the periodic General Queries.
The allowed range is 0 to 31744 in tenths of seconds, default query response

interval is 100 in tenths of seconds (10 seconds).
 LLQI (LMQI for IGMP) Last Member Query Interval. The Last Member Query Time is the time value
represented by the Last Member Query Interval, multiplied by the Last Member
Query Count.
The allowed range is 0 to 31744 in tenths of seconds, default last member query
interval is 10 in tenths of seconds (1 second).
 URI Unsolicited Report Interval. The Unsolicited Report Interval is the time between
repetitions of a host's initial report of membership in a group.
The allowed range is 0 to 31744 seconds, default unsolicited report interval is 1

second.
Buttons
: Refreshes the displayed table starting from the "VLAN" input fields.
: Click to add new IGMP VLAN. Specify the VID and configure the new entry.
Click "Save". The specific IGMP VLAN starts working after the corresponding static VLAN is also created.
157
4.8.6 IGMP Snooping Port Group Filtering
In certain switch applications, the administrator may want to control the multicast services that are available to end users. For
example, an IP/TV service based on a specific subscription plan. The IGMP filtering feature fulfills this requirement by restricting
access to specified multicast services on a switch port, and IGMP throttling limits the number of simultaneous multicast groups a
port can join.
IGMP filtering enables you to assign a profile to a switch port that specifies multicast groups that are permitted or denied on the
port. An IGMP filter profile can contain one or more, or a range of multicast addresses; but only one profile can be assigned to a
port. When enabled, IGMP join reports received on the port are checked against the filter profile. If a requested multicast group
is permitted, the IGMP join report is forwarded as normal. If a requested multicast group is denied, the IGMP join report is
dropped.
IGMP throttling sets a maximum number of multicast groups that a port can join at the same time. When the maximum number
of groups is reached on a port, the switch can take one of two actions; either “deny” or “replace”. If the action is set to deny, any
new IGMP join reports will be dropped. If the action is set to replace, the switch randomly removes an existing group and
replaces it with the new multicast group. The IGMP Snooping Port Group Filtering Configuration screen in Figure 4-8-9 appears.
Figure 4-8-9: IGMP Snooping Port Filtering Profile Configuration Page Screenshot
Object Description
 Port The logical port for the settings.
 Filtering Profile Select the IPMC Profile as the filtering condition for the specific port. Summary
about the designated profile will be shown by clicking the view button
Buttons
158
4.8.7 IGMP Snooping Status
This Page provides IGMP Snooping status. The IGMP Snooping Status screen in Figure 4-8-10 appears.
Figure 4-8-10: IGMP Snooping Status Page Screenshot
Object Description
 Querier Version Working Querier Version currently.
 Host Version Working Host Version currently.
 Querier Status Show the Querier status is "ACTIVE" or "IDLE".
 Querier Transmitted The number of Transmitted Querier.
 Querier Received The number of Received Querier.
 V1 Reports Received The number of Received V1 Reports.
 V2 Leave Received The number of Received V2 Leave.
 Router Port Display which ports act as router ports. A router port is a port on the Ethernet
switch that leads towards the Layer 3 multicast device or IGMP querier.
Static denotes the specific port is configured to be a router port.
Dynamic denotes the specific port is learnt to be a router port.
Both denote the specific port is configured or learnt to be a router port.
 Port Switch port number.
 Status Indicate whether specific port is a router port or not.
159
Buttons
: Clears all Statistics counters.

4.8.8 IGMP Group Information
Entries in the IGMP Group Table are shown on this Page. The IGMP Group Table is sorted first by VLAN ID, and then by group.
Each Page shows up to 99 entries from the IGMP Group table, default being 20, selected through the "entries per Page" input
field. When first visited, the web Page will show the first 20 entries from the beginning of the IGMP Group Table. The "Start from
VLAN", and "group" input fields allow the user to select the starting point in the IGMP Group Table. The IGMP Groups
Information screen in Figure 4-8-11 appears.
Figure 4-8-9: IGMP Snooping Groups Information Page Screenshot
Object Description
 VLAN ID VLAN ID of the group.
 Groups Group address of the group displayed.
 Port Members Ports under this group.
Buttons
: Updates the table, starting with the first entry in the IGMP Group Table.
160
4.8.9 IGMPv3 Information
Entries in the IGMP SSM Information Table are shown on this Page. The IGMP SSM Information Table is sorted first by VLAN ID,
then by group, and then by Port No. Diffrent source addresses belong to the same group are treated as single entry.
Each Page shows up to 99 entries from the IGMP SSM (Source Specific Multicast) Information table, default being 20, selected
through the "entries per Page" input field. When first visited, the web Page will show the first 20 entries from the beginning of the
IGMP SSM Information Table.
The "Start from VLAN", and "Group" input fields allow the user to select the starting point in the IGMP SSM Information Table.
The IGMPv3 Information screen in Figure 4-8-12 appears.
Figure 4-8-12: IGMP SSM Information Page Screenshot
Object Description
 Group Group address of the group displayed.
 Mode Indicates the filtering mode maintained per (VLAN ID, port number, Group
Address) basis. It can be either Include or Exclude.
 Source Address IP Address of the source. Currently, system limits the total number of IP source
addresses for filtering to be 128.
 Type Indicates the Type. It can be either Allow or Deny.
 Hardware Filter/Switch Indicates whether data plane destined to the specific group address from the
source IPv4 address could be handled by chip or not.
Buttons
161
4.8.10 MLD Snooping Configuration
This Page provides MLD Snooping related configuration. The MLD Snooping Configuration screen in Figure 4-8-13 appears.
Figure 4-8-13: MLD Snooping Configuration Page Screenshot
Object Description
 Snooping Enabled Enable the Global MLD Snooping.
 Unregistered IPMCv6 Enable unregistered IPMCv6 traffic flooding.
Flooding enabled The flooding control takes effect only when MLD Snooping is enabled.
When MLD Snooping is disabled, unregistered IPMCv6 traffic flooding is always
active in spite of this setting.
 MLD SSM Range SSM (Source-Specific Multicast) Range allows the SSM-aware hosts and routers
run the SSM service model for the groups in the address range.
 Leave Proxy Enable Enable MLD Leave Proxy. This feature can be used to avoid forwarding
unnecessary leave messages to the router side.
 Proxy Enable Enable MLD Proxy. This feature can be used to avoid forwarding unnecessary
join and leave messages to the router side.
 Router Port Specify which ports act as router ports. A router port is a port on the Ethernet
162
switch that leads towards the Layer 3 multicast device or MLD querier.
If an aggregation member port is selected as a router port, the whole aggregation
will act as a router port. The allowed selection is Auto, Fix, Fone, default
compatibility value is Auto.
 Fast Leave Enable the fast leave on the port.
 Throtting Enable to limit the number of multicast groups to which a switch port can belong.
Buttons
4.8.11 MLD Snooping VLAN Configuration
Each Page shows up to 99 entries from the VLAN table, default being 20, selected through the "entries per Page" input field.
When first visited, the web Page will show the first 20 entries from the beginning of the VLAN Table. The first displayed will be
the one with the lowest VLAN ID found in the VLAN Table.
The "VLAN" input fields allow the user to select the starting point in the VLAN Table. The MLD Snooping VLAN Configuration
Figure 4-8-14: IGMP Snooping VLAN Configuration Page Screenshot
Object Description
save.
 MLD Snooping Enable Enable the per-VLAN MLD Snooping. Up to 32 VLANs can be selected for MLD
Snooping.
163
 Querier Election Enable to join MLD Querier election in the VLAN. Disable to act as a MLD
Non-Querier.
 Compatibility Compatibility is maintained by hosts and routers taking appropriate actions
depending on the versions of MLD operating on hosts and routers within a

network. The allowed selection is MLD-Auto, Forced MLDv1, Forced MLDv2,
default compatibility value is MLD-Auto.
 PRI (PRI) Priority of Interface. It indicates the MLD control frame priority level
generated by the system. These values can be used to prioritize different classes
of traffic. The allowed range is 0 (best effort) to 7 (highest), default interface

priority value is 0
 RV Robustness Variable. The Robustness Variable allows tuning for the expected
packet loss on a network. The allowed range is 1 to 255, default robustness
variable value is 2.
 QI Query Interval. The Query Interval is the interval between General Queries sent
by the Querier. The allowed range is 1 to 31744 seconds, default query interval is
125 seconds.
 QRI Query Response Interval. The Max Response Time used to calculate the Max
Resp Code inserted into the periodic General Queries. The allowed range is 0 to
31744 in tenths of seconds, default query response interval is 100 in tenths of

seconds (10 seconds).
 LLQI (LMQI for IGMP) Last Member Query Interval. The Last Member Query Time is the time value
represented by the Last Member Query Interval, multiplied by the Last Member
Query Count. The allowed range is 0 to 31744 in tenths of seconds, default last
member query interval is 10 in tenths of seconds (1 second).
 URI Unsolicited Report Interval. The Unsolicited Report Interval is the time between
repetitions of a host's initial report of membership in a group. The allowed range
is 0 to 31744 seconds, default unsolicited report interval is 1 second.
Buttons
: Refreshes the displayed table starting from the "VLAN" input fields.
:Click to add new MLD VLAN. Specify the VID and configure the new entry.
Click "Save". The specific MLD VLAN starts working after the corresponding static VLAN is also created.
164
4.8.12 MLD Snooping Port Group Filtering
In certain switch applications, the administrator may want to control the multicast services that are available to end users. For
example, an IP/TV service based on a specific subscription plan. The MLD filtering feature fulfills this requirement by restricting
access to specified multicast services on a switch port, and MLD throttling limits the number of simultaneous multicast groups a
port can join.
MLD filtering enables you to assign a profile to a switch port that specifies multicast groups that are permitted or denied on the
port. A MLD filter profile can contain one or more, or a range of multicast addresses; but only one profile can be assigned to a
port. When enabled, MLD join reports received on the port are checked against the filter profile. If a requested multicast group is
permitted, the MLD join report is forwarded as normal. If a requested multicast group is denied, the MLD join report is dropped.
MLD throttling sets a maximum number of multicast groups that a port can join at the same time. When the maximum number of
groups is reached on a port, the switch can take one of two actions; either “deny” or “replace”. If the action is set to deny, any
new MLD join reports will be dropped. If the action is set to replace, the switch randomly removes an existing group and
replaces it with the new multicast group. The MLD Snooping Port Group Filtering Configuration screen in Figure 4-8-15 appears.
Figure 4-8-15: MLD Snooping Port Group Filtering Configuration Page Screenshot
Object Description
 Filtering Group Select the IPMC Profile as the filtering condition for the specific port. Summary
about the designated profile will be shown by clicking the view button.
Buttons
165
4.8.13 MLD Snooping Status
This Page provides MLD Snooping status. The IGMP Snooping Status screen in Figure 4-8-16 appears.
Figure 4-8-16: MLD Snooping Status Page Screenshot
Object Description
 Querier Version Working Querier Version currently.
 Host Version Working Host Version currently.
 Querier Status Shows the Querier status is "ACTIVE" or "IDLE".
"DISABLE" denotes the specific interface is administratively disabled.
 Querier Transmitted The number of Transmitted Querier.
 Querier Received The number of Received Querier.
 V1 Leave Received The number of Received V1 Leaves.
 Router Port Display which ports act as router ports. A router port is a port on the Ethernet
switch that leads towards the Layer 3 multicast device or MLD querier.
Static denotes the specific port is configured to be a router port.
Dynamic denotes the specific port is learnt to be a router port.
Both denote the specific port is configured or learnt to be a router port.
166
 Status Indicates whether specific port is a router port or not.
Buttons
4.8.14 MLD Group Information
Entries in the MLD Group Table are shown on this Page. The MLD Group Table is sorted first by VLAN ID, and then by group.
Each Page shows up to 99 entries from the MLD Group table, default being 20, selected through the "entries per Page" input
field. When first visited, the web Page will show the first 20 entries from the beginning of the MLD Group Table.
The "Start from VLAN", and "group" input fields allow the user to select the starting point in the MLD Group Table. The MLD
Groups Informatino screen in Figure 4-8-17 appears.
Figure 4-8-17: MLD Snooping Groups Information Page Screenshot
Object Description
 Groups Group address of the group displayed.
Buttons
167
4.8.15 MLDv2 Information
Entries in the MLD SFM Information Table are shown on this Page. The MLD SFM (Source-Filtered Multicast) Information Table
also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and then by
Port. Different source addresses belong to the same group are treated as single entry. Each Page shows up to 99 entries from
the MLD SFM Information table, default being 20, selected through the "entries per Page" input field. When first visited, the web
Page will show the first 20 entries from the beginning of the MLD SFM Information Table.
The "Start from VLAN", and "group" input fields allow the user to select the starting point in the MLD SFM Information Table.
The MLDv2 Information screen in Figure 4-8-18 appears.
Figure 4-8-18: MLD SSM Information Page Screenshot
Object Description
addresses for filtering to be 128.
 Hardware Filter/Switch Indicates whether data plane destined to the specific group address from the
source IPv6 address could be handled by chip or not.
Buttons
: Updates the table starting from the first entry in the MLD SFM Information Table.
168
4.8.16 MVR (Multicaset VLAN Registration)
The MVR feature enables multicast traffic forwarding on the Multicast VLANs.
■ In a multicast television application, a PC or a network television or a set-top box can receive the multicast stream.
■ Multiple set-top boxes or PCs can be connected to one subscriber port, which is a switch port configured as an MVR
receiver port. When a subscriber selects a channel, the set-top box or PC sends an IGMP/MLD report message to Switch
A to join the appropriate multicast group address.
■ Uplink ports that send and receive multicast data to and from the multicast VLAN are called MVR source ports.
It is allowed to create at maximun 8 MVR VLANs with corresponding channel settings for each Multicast VLAN. There will be
totally at maximun 256 group addresses for channel settings.
This Page provides MVR related configuration. The MVR screen in Figure 4-8-19 appears.
169
Figure 4-8-19: MVR Configuration Page Screenshot
Object Description
 MVR Mode Enable/Disable the Global MVR.
The Unregistered Flooding control depends on the current configuration in
IGMP/MLD Snooping.
It is suggested to enable Unregistered Flooding control when the MVR group
table is full.
save.
 MVR VID Specify the Multicast VLAN ID.
Be Caution: MVR source ports are not recommended to be overlapped with

management VLAN ports.
 MVR Name MVR Name is an optional attribute to indicate the name of the specific MVR
VLAN. Maximum length of the MVR VLAN Name string is 16. MVR VLAN Name
can only contain alphabets or numbers. When the optional MVR VLAN name is
170
given, it should contain at least one alphabet. MVR VLAN name can be edited for
the existing MVR VLAN entries or it can be added to the new entries.
 IGMP Address Define the IPv4 address as source address used in IP header for IGMP control
frames. The default IGMP address is not set (0.0.0.0).

When the IGMP address is not set, system uses IPv4 management address of
the IP interface associated with this VLAN.
When the IPv4 management address is not set, system uses the first available
IPv4 management address. Otherwise, system uses a pre-defined value. By
default, this value will be 192.0.2.1.
 Mode Specify the MVR mode of operation. In Dynamic mode, MVR allows dynamic
MVR membership reports on source ports. In Compatible mode, MVR
membership reports are forbidden on source ports. The default is Dynamic
mode.
 Tagging Specify whether the traversed IGMP/MLD control frames will be sent as
Untagged or Tagged with MVR VID. The default is Tagged.
 Priority Specify how the traversed IGMP/MLD control frames will be sent in prioritized
manner. The default Priority is 0.
 LLQI Define the maximun time to wait for IGMP/MLD report memberships on a
receiver port before removing the port from multicast group membership. The
value is in units of tenths of a seconds. The range is from 0 to 31744. The default
LLQI is 5 tenths or one-half second.
 Interface Channel When the MVR VLAN is created, select the IPMC Profile as the channel filtering
Setting condition for the specific MVR VLAN. Summary about the Interface Channel
Profiling (of the MVR VLAN) will be shown by clicking the view button. Profile
selected for designated interface channel is not allowed to have overlapped
permit group address.
 Port Role Configure an MVR port of the designated MVR VLAN as one of the following
roles.
 Inactive: The designated port does not participate MVR operations.

 Source: Configure uplink ports that receive and send multicast data as
source ports. Subscribers cannot be directly connected to source ports.
 Receiver: Configure a port as a receiver port if it is a subscriber port and

should only receive multicast data. It does not receive data unless it
becomes a member of the multicast group by issuing IGMP/MLD messages.
Be Caution: MVR source ports are not recommended to be overlapped with

management VLAN ports.
Select the port role by clicking the Role symbol to switch the setting.
I indicates Inactive; S indicates Source; R indicates Receiver
171
The default Role is Inactive.
 Immediate Leave Enable the fast leave on the port.
Buttons
: Click to add new MVR VLAN. Specify the VID and configure the new entry. Click "Save"
4.8.17 MVR Status
This Page provides MVR status. The MVR Status screen in Figure 4-8-20 appears.
Figure 4-8-20: MVR Status Page Screenshot
Object Description
 VLAN ID The Multicast VLAN ID.
 IGMP/MLD Queries Received The number of Received Queries for IGMP and MLD, respectively.
 IGMP/MLD Queries Transmitted The number of Transmitted Queries for IGMP and MLD, respectively.
 IGMPv1 Joins Received The number of Received IGMPv1 Joins.
 IGMPv2/MLDv1 Reports Received The number of Received IGMPv2 Joins and MLDv1 Reports, respectively.
 IGMPv3/MLDv2 Reports Received The number of Received IGMPv1 Joins and MLDv2 Reports, respectively.
 IGMPv2/MLDv1 Leaves Received The number of Received IGMPv2 Leaves and MLDv1 Dones, respectively.
Buttons
172
4.8.18 MVR Groups Information
Entries in the MVR Group Table are shown on this Page. The MVR Group Table is sorted first by VLAN ID, and then by group.
Each Page shows up to 99 entries from the MVR Group table, default being 20, selected through the "entries per Page" input
field. When first visited, the web Page will show the first 20 entries from the beginning of the MVR Group Table.
The "Start from VLAN", and "group" input fields allow the user to select the starting point in the MVR Group Table. The MVR
Groups Information screen in Figure 4-8-21 appears.
Figure 4-8-21: MVR Groups Information Page Screenshot
Object Description
 VLAN VLAN ID of the group.
 Groups Group ID of the group displayed.
Buttons
: Updates the table starting from the first entry in the MVR Channels (Groups) Information Table.
4.8.19 MVR SFM Information
Entries in the MVR SFM Information Table are shown on this Page. The MVR SFM (Source-Filtered Multicast) Information
Table also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and
then by Port. Different source addresses belong to the same group are treated as single entry.
173
Each Page shows up to 99 entries from the MVR SFM Information Table, default being 20, selected through the "entries per
Page" input field. When first visited, the web Page will show the first 20 entries from the beginning of the MVR SFM Information
Table.
The "Start from VLAN", and "Group Address" input fields allow the user to select the starting point in the MVR SFM Information
Table. The MVR SFM Information screen in Figure 4-8-22 appears.
Figure 4-8-22: MVR SFM Information Page Screenshot
Object Description
addresses for filtering to be 128. When there is no any source filtering address,
the text "None" is shown in the Source Address field.
 Hardware Filter / Indicates whether data plane destined to the specific group address from the
Switch source IPv4/IPv6 address could be handled by chip or not.
Buttons
: Updates the table starting from the first entry in the MVR SFM Information Table.
174
4.9 Quality of Service
4.9.1 Understanding QoS
Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic. QoS
enables you to assign various grades of network service to different types of traffic, such as multi-media, video, protocol-specific,
time critical, and file-backup traffic.
QoS reduces bandwidth limitations, delay, loss, and jitter. It also provides increased reliability for delivery of your data and
allows you to prioritize certain applications across your network. You can define exactly how you want the switch to treat
selected applications and types of traffic. You can use QoS on your system to:
 Control a wide variety of network traffic by:
 Classifying traffic based on packet attributes.
 Assigning priorities to traffic (for example, to set higher priorities to time-critical or business-critical applications).
 Applying security policy through traffic filtering.
 Provide predictable throughput for multimedia applications such as video conferencing or voice over IP by minimizing
delay and jitter.
 Improve performance for specific types of traffic and preserve performance as the amount of traffic grows.
 Reduce the need to constantly add bandwidth to the network.
 Manage network congestion.
QoS Terminology
 Classifier－classifies the traffic on the network. Traffic classifications are determined by protocol, application, source,
destination, and so on. You can create and modify classifications. The Switch then groups classified traffic in order to
schedule them with the appropriate service level.

 DiffServ Code Point (DSCP) － is the traffic prioritization bits within an IP header that are encoded by certain
applications and/or devices to indicate the level of service required by the packet across a network.
 Service Level－defines the priority that will be given to a set of classified traffic. You can create and modify service
levels.
 Policy－comprises a set of “rules” that are applied to a network so that a network meets the needs of the business. That
is, traffic can be prioritized across a network according to its importance to that particular business type.
 QoS Profile－consists of multiple sets of rules (classifier plus service level combinations). The QoS profile is assigned
to a port(s).
 Rules－comprises a service level and a classifier to define how the Switch will treat certain types of traffic. Rules are
associated with a QoS Profile (see above).
To implement QoS on your network, you need to carry out the following actions:
1. Define a service level to determine the priority that will be applied to traffic.
2. Apply a classifier to determine how the incoming traffic will be classified and thus treated by the Switch.
3. Create a QoS profile which associates a service level and a classifier.
4. Apply a QoS profile to a port(s).
175
4.9.2 Port Policing
This Page allows you to configure the Policer settings for all switch ports. The Port Policing screen in Figure 4-9-1 appears.
Figure 4-9-1: QoS Ingress Port Policers Page Screenshot
Object Description
 Port The port number for which the configuration below applies.
 Enable Controls whether the policer is enabled on this switch port.
 Rate Controls the rate for the policer. This value is restricted to 100-1000000 when the
"Unit" is "kbps" or "fps", and it is restricted to 1-3300 when the "Unit" is "Mbps"
or "kfps".
The default value is 500.
 Unit Controls the unit of measure for the policer rate as kbps, Mbps, fps or kfps .
The default value is "kbps".
 Flow Control If flow control is enabled and the port is in flow control mode, then pause frames
are sent instead of discarding frames.
Buttons
4.9.3 Port Classification
This Page allows you to configure the basic QoS Ingress Classification settings for all switch ports. The Port Classification
176
Figure 4-9-2 : QoS Ingress Port Classification Page Screenshot
Object Description
 CoS Controls the default class of service.
All frames are classified to a CoS. There is a one to one mapping between CoS,
queue and priority. A CoS of 0 (zero) has the lowest priority.
If the port is VLAN aware and the frame is tagged, then the frame is classified to
a CoS that is based on the PCP value in the tag as shown below. Otherwise the
frame is classified to the default CoS.
PCP value: 0 1 2 3 4 5 6 7
CoS value: 1 0 2 3 4 5 6 7
The classified CoS can be overruled by a QCL entry.
Note: If the default CoS has been dynamically changed, then the actual default
CoS is shown in parentheses after the configured default CoS.
 DPL Controls the default drop precedence level.
All frames are classified to a drop precedence level.
If the port is VLAN aware and the frame is tagged, then the frame is classified to
a DPL that is equal to the DEI value in the tag. Otherwise the frame is classified
to the default DPL. The classified DPL can be overruled by a QCL entry
 DSCP Based Click to Enable DSCP Based QoS Ingress Port Classification.
Buttons
177
4.9.4 Port Scheduler
This Page provides an overview of QoS Egress Port Schedulers for all switch ports. The Port Scheduler screen in Figure 4-9-3
appears.
Figure 4-9-3: QoS Egress Port Schedule Page Screenshot
Object Description
Click on the port number in order to configure the schedulers.
For more detail, please refer to chapter 4.9.5.1.
 Mode Shows the scheduling mode for this port.
 Q0 ~ Q5 Shows the weight for this queue and port.
178
4.9.5 Port Shaping
This Page provides an overview of QoS Egress Port Shapers for all switch ports. The Port Shapping screen in Figure 4-9-4
appears.
Figure 4-9-4: QoS Egress Port Shapers Page Screenshot
Object Description
Click on the port number in order to configure the shapers.
 Q0 ~Q7 Shows "disabled" or actual queue shaper rate - e.g. "800 Mbps".
 Port Shows "disabled" or actual port shaper rate - e.g. "800 Mbps".
179
4.9.5.1 QoS Egress Port Schedule and Shapers
The Port Scheduler and Shapers for a specific port are configured on this Page. The QoS Egress Port Schedule and Shaper
sscreen in Figure 4-9-5 appears.
Figure 4-9-5: QoS Egress Port Schedule and Shapers Page Screenshot
Object Description
 Schedule Mode Controls whether the scheduler mode is "Strict Priority" or "Weighted" on this
switch port.
 Queue Shaper Enable Controls whether the queue shaper is enabled for this queue on this switch port.
 Queue Shaper Rate Controls the rate for the queue shaper.
This value is restricted to 100-1000000 when the "Unit" is "kbps", and it is
restricted to 1-13200 when the "Unit" is "Mbps".
 Queue Shaper Unit Controls the unit of measure for the queue shaper rate as "kbps" or "Mbps".
 Queue Shaper Excess Controls whether the queue is allowed to use excess bandwidth.
 Queue Scheduler Controls the weight for this queue.
180
Weight This value is restricted to 1-100. This parameter is only shown if "Scheduler
Mode" is set to "Weighted".
The default value is "17".
 Queue Scheduler Shows the weight in percent for this queue. This parameter is only shown if
Percent "Scheduler Mode" is set to "Weighted".
 Port Shaper Enable Controls whether the port shaper is enabled for this switch port.
 Port Shaper Rate Controls the rate for the port shaper.
This value is restricted to 100-1000000 when the "Unit" is "kbps", and it is
restricted to 1-13200 when the "Unit" is "Mbps".
 Port Shaper Unit Controls the unit of measure for the port shaper rate as "kbps" or "Mbps".
Buttons
: Click to undo any changes made locally and return to the previous Page.
4.9.6 Port Tag Remarking
This Page provides an overview of QoS Egress Port Tag Remarking for all switch ports. The Port Tag Remarking screen in
Figure 4-9-6: QoS Egress Port Tag Remarking Page Screenshot
181
Object Description
Click on the port number in order to configure tag remarking.
 Mode Shows the tag remarking mode for this port.
■ Classified: Use classified PCP/DEI values
■ Default: Use default PCP/DEI values.
■ Mapped: Use mapped versions of QoS class and DP level.
4.9.6.1 QoS Egress Port Tag Remarking
The QoS Egress Port Tag Remarking for a specific port are configured on this Page. The QoS Egress Port Tag Remarking
sscreen in Figure 4-9-7 appears.
Figure 4-9-7: QoS Egress Port Tag Remarking Page Screenshot
Object Description
 Mode Controls the tag remarking mode for this port.
■ Classified: Use classified PCP/DEI values.
■ Default: Use default PCP/DEI values.
■ Mapped: Use mapped versions of QoS class and DP level.
 PCP/DEI Configuration Controls the default PCP and DEI values used when the mode is set to Default.
 (QoS class, DP level) Controls the mapping of the classified (QoS class, DP level) to (PCP, DEI) values
to (PCP, DEI) Mapping when the mode is set to Mapped.
Buttons
182
4.9.7 Port DSCP
This Page allows you to configure the basic QoS Port DSCP Configuration settings for all switch ports. The Port DSCP screen in
Figure 4-9-8: QoS Port DSCP Configuration Page Screenshot
Object Description
 Port The Port coulmn shows the list of ports for which you can configure dscp ingress
and egress settings.
 Ingress In Ingress settings you can change ingress translation and classification settings
for individual ports.
There are two configuration parameters available in Ingress:
 Translate
 Classify
 Translate To Enable the Ingress Translation click the checkbox.
 Classify Classification for a port have 4 different values.
 Disable: No Ingress DSCP Classification.

 DSCP=0: Classify if incoming (or translated if enabled) DSCP is 0.
 Selected: Classify only selected DSCP for which classification is enabled
as specified in DSCP Translation window for the specific DSCP.
 All: Classify all DSCP.
 Egress Port Egress Rewriting can be one of -
 Disable: No Egress rewrite.
 Enable: Rewrite enable without remapped.
 Remap DP Unaware: DSCP from analyzer is remapped and frame is
183
remarked with remapped DSCP value. The remapped DSCP value is
always taken from the 'DSCP Translation->Egress Remap DP0' table.
 Remap DP Aware: DSCP from analyzer is remapped and frame is

remarked with remapped DSCP value. Depending on the DP level of the
frame, the remapped DSCP value is either taken from the 'DSCP
Translation->Egress Remap DP0' table or from the 'DSCP
Translation->Egress Remap DP1' table.
Buttons
4.9.8 DSCP-based QoS
This Page allows you to configure the basic QoS DSCP-based QoS Ingress Classification settings for all switches. The
DSCP-based QoS screen in Figure 4-9-9 appears.
Figure 4-9-9: DSCP-based QoS Ingress Classification Page Screenshot
184
Object Description
 DSCP Maximum number of support ed DSCP values are 64.
 Trust Controls whether a specific DSCP value is trusted. Only frames with trusted
DSCP values are mapped to a specific QoS class and Drop Precedence Level.
Frames with untrusted DSCP values are treated as a non-IP frame.
 QoS Class QoS Class value can be any of (0-7)
 DPL Drop Precedence Level (0-1)
4.9.9 DSCP Translation
This Page allows you to configure the basic QoS DSCP Translation settings for all switches. DSCP translation can be done in
Ingress or Egress. The DSCP Translation screen in Figure 4-9-10 appears.
Figure 4-9-10: DSCP Translation Page Screenshot
Object Description
185
 DSCP Maximum number of supported DSCP values are 64 and valid DSCP value
ranges from 0 to 63.
 Ingress Ingress side DSCP can be first translated to new DSCP before using the DSCP
for QoS class and DPL map.
There are two configuration parameters for DSCP Translation –
■ Translate
■ Classify
 Translate DSCP at Ingress side can be translated to any of (0-63) DSCP values.
 Classify Click to enable Classification at Ingress side.
 Egress There is following configurable parameter for Egress side -
■ Remap
 Remap DP Select the DSCP value from select menu to which you want to remap. DSCP
value ranges form 0 to 63.
Buttons
4.9.10 DSCP Classification
This Page allows you to map DSCP value to a QoS Class and DPL value. The DSCP Classification screen in Figure 4-9-11
appears.
Figure 4-9-11: DSCP Classification Page Screenshot
186
Object Description
 QoS Class Available QoS Class value ranges from 0 to 7. QoS Class (0-7) can be mapped
to followed parameters.
 DPL Actual Drop Precedence Level.
 DSCP Select DSCP value (0-63) from DSCP menu to map DSCP to corresponding QoS
Class and DPL value
Buttons
4.9.11 QoS Control List
This Page shows the QoS Control List(QCL), which is made up of the QCEs. Each row describes a QCE that is defined. The
maximum number of QCEs is 256 on each switch.
Click on the lowest plus sign to add a new QCE to the list. The QoS Control List screen in Figure 4-9-12 appears.
Figure 4-9-12: QoS Control List Configuration Page Screenshot
Object Description
 QCE# Indicates the index of QCE.
 Port Indicates the list of ports configured with the QCE.
 DMAC Specify the type of Destination MAC addresses for incoming frame. Possible
values are:
■ Any: All types of Destination MAC addresses are allowed.
■ Unicast: Only Unicast MAC addresses are allowed.
■ Multicast: Only Multicast MAC addresses are allowed.
187
■ Broadcast: Only Broadcast MAC addresses are allowedd.

The default value is 'Any'.
 SMAC Displays the OUI field of Source MAC address, i.e. first three octet (byte) of MAC
address.
 Tag Type Indicates tag type. Possible values are:
■ Any: Match tagged and untagged frames.
■ Untagged: Match untagged frames.
■ Tagged: Match tagged frames.

The default value is 'Any'
 VID Indicates (VLAN ID), either a specific VID or range of VIDs. VID can be in the
range 1-4095 or 'Any'
 PCP Priority Code Point: Valid value PCP are specific(0, 1, 2, 3, 4, 5, 6, 7) or
range(0-1, 2-3, 4-5, 6-7, 0-3, 4-7) or 'Any'.
 DEI Drop Eligible Indicator: Valid value of DEI can be any of values between 0, 1 or
'Any'.
 Frame Type Indicates the type of frame to look for incomming frames. Possible frame types
are:
■ Any: The QCE will match all frame type.
■ Ethernet: Only Ethernet frames (with Ether Type 0x600-0xFFFF) are

allowed.
■ LLC: Only (LLC) frames are allowed.
■ SNAP: Only (SNAP) frames are allowed.
■ IPv4: The QCE will match only IPV4 frames.
 Action Indicates the classification action taken on ingress frame if parameters
configured are matched with the frame's content.
There are three action fields: Class, DPL and DSCP.
■ Class: Classified QoS class.
■ DPL: Classified Drop Precedence Level.
■ DSCP: Classified DSCP value.
 Modification Buttons You can modify each QCE in the table using the following buttons:
: Inserts a new QCE before the current row.
: Edits the QCE.
: Moves the QCE up the list.
: Moves the QCE down the list.
: Deletes the QCE.
: The lowest plus sign adds a new entry at the bottom of the list of QCL.
188
4.9.11.1 QoS Control Entry Configuration
The QCE Configuration screen in Figure 4-9-13 appears.
Figure 4-9-13: QCE Configuration Page Screenshot
Object Description
 Port Members Check the checkbox button in case you what to make any port member of the
QCL entry. By default all ports will be checked
 Key Parameters Key configuration are discribed as below:
■ DMAC Type Destination MAC type: possible values are unicast(UC),

multicast(MC), broadcast(BC) or 'Any'
■ SMAC Source MAC address: 24 MS bits (OUI) or 'Any'
■ Tag Value of Tag field can be 'Any', 'Untag' or 'Tag'
■ VID Valid value of VLAN ID can be any value in the range 1-4095 or 'Any';
user can enter either a specific value or a range of VIDs
■ PCP Priority Code Point: Valid value PCP are specific(0, 1, 2, 3, 4, 5, 6, 7)

or range(0-1, 2-3, 4-5, 6-7, 0-3, 4-7) or 'Any'
■ DEI Drop Eligible Indicator: Valid value of DEI can be any of values
between 0, 1 or 'Any'
■ Frame Type Frame Type can have any of the following values
1. Any
2. Ethernet
189
3. LLC
4. SNAP
5. IPv4
6. IPv6
Note: all frame types are explained below.
 Any Allow all types of frames.
 EtherType Ethernet Type Valid ethernet type can have value within 0x600-0xFFFF or 'Any'
but excluding 0x800(IPv4) and 0x86DD(IPv6), default value is 'Any'.
 LLC ■ SSAP Address Valid SSAP(Source Service Access Point) can vary from
0x00 to 0xFF or 'Any', the default value is 'Any'
■ DSAP Address Valid DSAP(Destination Service Access Point) can vary

from 0x00 to 0xFF or 'Any', the default value is 'Any'
■ Control Address Valid Control Address can vary from 0x00 to 0xFF or
'Any', the default value is 'Any'
 SNAP PID Valid PID(a.k.a ethernet type) can have value within 0x00-0xFFFF or 'Any',
default value is 'Any'
 IPv4 ■ Protocol IP protocol number: (0-255, TCP or UDP) or 'Any'
■ Source IP Specific Source IP address in value/mask format or 'Any'. IP and

Mask are in the format x.y.z.w where x, y, z, and w are decimal numbers
between 0 and 255. When Mask is converted to a 32-bit binary string and
read from left to right, all bits following the first zero must also be zero
DSCP Diffserv Code Point value(DSCP): It can be specific value, range of

value or 'Any'. DSCP values are in the range 0-63 including BE, CS1-CS7,
EF or AF11-AF43
■ IP Fragment IPv4 frame fragmented option: yes|no|any
■ Sport Source TCP/UDP port:(0-65535) or 'Any', specific or port range

applicable for IP protocol UDP/TCP
■ Dport Destination TCP/UDP port:(0-65535) or 'Any', specific or port range

 IPv6 Protocol IP protocol number: (0-255, TCP or UDP) or 'Any'
Source IP IPv6 source address: (a.b.c.d) or 'Any', 32 LS bits
DSCP Diffserv Code Point value(DSCP): It can be specific value, range of value
or 'Any'. DSCP values are in the range 0-63 including BE, CS1-CS7, EF or
AF11-AF43
Sport Source TCP/UDP port:(0-65535) or 'Any', specific or port range applicable

for IP protocol UDP/TCP
Dport Destination TCP/UDP port:(0-65535) or 'Any', specific or port range

 Action Parameters Class QoS class: (0-7) or 'Default'.
190
DPL Valid Drop Precedence Level can be (0-3) or 'Default'.
DSCP Valid DSCP value can be (0-63, BE, CS1-CS7, EF or AF11-AF43) or

'Default'.
'Default' means that the default classified value is not modified by this QCE.
Buttons
: Click to undo any changes made locally and revert to previously saved values
: Return to the previous Page without saving the configuration change
4.9.12 QCL Status
This Page shows the QCL status by different QCL users. Each row describes the QCE that is defined. It is a conflict if a specific
QCE is not applied to the hardware due to hardware limitations. The maximum number of QCEs is 256 on each switch. The
QoS Control List Status screen in Figure 4-9-14 appears.
Figure 4-9-14: QoS Control List Status Page Screenshot
Object Description
 User Indicates the QCL user.
 QCE# Indicates the index of QCE.
 Port Indicates the list of ports configured with the QCE.
 Frame Type Indicates the type of frame to look for incomming frames. Possible frame types
are:
■ Any: The QCE will match all frame type.
■ Ethernet: Only Ethernet frames (with Ether Type 0x600-0xFFFF) are

allowed.
191
■ LLC: Only (LLC) frames are allowed.
■ SNAP: Only (SNAP) frames are allowed.
 Action Indicates the classification action taken on ingress frame if parameters
configured are matched with the frame's content.
There are three action fields: Class, DPL and DSCP.
■ Class: Classified QoS class; if a frame matches the QCE it will be

put in the queue.
■ DPL: Drop Precedence Level; if a frame matches the QCE then DP

level will set to value displayed under DPL column.
■ DSCP: If a frame matches the QCE then DSCP will be classified with
the value displayed under DSCP column.
 Conflict Displays Conflict status of QCL entries. As H/W resources are shared by multiple
applications. It may happen that resources required to add a QCE may not be
available, in that case it shows conflict status as 'Yes', otherwise it is always 'No'.
Please note that conflict can be resolved by releasing the H/W resources
required to add QCL entry on pressing 'Resolve Conflict' button.
Buttons
: Select the QCL status from this drop down list.
: Click to release the resources required to add QCL entry, in case the conflict status for any QCL entry
is 'yes'.
4.9.13 Storm Control Configuration
Storm control for the switch is configured on this Page. There is a unicast storm rate control, multicast storm rate control, and a
broadcast storm rate control. These only affect flooded frames, i.e. frames with a (VLAN ID, DMAC) pair not present on the MAC
Address table.
The configuration indicates the permitted packet rate for unicast, multicast or broadcast traffic across the switch.
The Storm Control Configuration screen in Figure 4-9-15 appears.
192
Figure 4-9-15: Storm Control Configuration Page Screenshot
Object Description
 Enable Controls whether the storm control is enabled on this switch port.
 Rate Controls the rate for the storm control. The default value is 500. This value is
restricted to 100-1000000 when the "Unit" is "kbps" or "fps", and it is restricted to
1-13200 when the "Unit" is "Mbps" or "kfps”.
 Unit Controls the unit of measure for the storm control rate as kbps, Mbps, fps or
kfps . The default value is "kbps".
Buttons
4.9.14 WRED
This page allows you to configure the Random Early Detection (RED) settings for queue 0 to 5. RED cannot be applied to
queue 6 and 7. Through different RED configuration for the queues (QoS classes) it is possible to obtain Weighted Random
Early Detection (WRED) operation between queues. The settings are global for all ports in the switch. The WRED screen in
193
Figure 4-9-16 WRED page screenshot
The page includes the following fields:
Object Description
 Queue The queue number (QoS class) for which the configuration below applies.
 Enable Controls whether RED is enabled for this queue.
 Min. Threshold Controls the lower RED threshold. If the average queue filling level is below this
threshold, the drop probability is zero.
This value is restricted to 0-100.
 Max. DP 1 Controls the drop probability for frames marked with Drop Precedence Level 1
when the average queue filling level is 100%.
 Max. DP2 Controls the drop probability for frames marked with Drop Precedence Level 2
 Max. DP3 Controls the drop probability for frames marked with Drop Precedence Level 3
RED Drop Probability Function

The following illustration shows the drop probability function with associated parameters.
194
Max. DP 1-3 is the drop probability when the average queue filling level is 100%. Frames marked with Drop Precedence Level 0
are never dropped. Min. Threshold is the average queue filling level where the queues randomly start dropping frames. The
drop probability for frames marked with Drop Precedence Level n increases linearly from zero (at Min. Threshold average queue
filling level) to Max. DP n (at 100% average queue filling level).
Buttons
195
4.9.15 QoS Statistics
This Page provides statistics for the different queues for all switch ports. The QoS Statistics screen in Figure 4-9-17 appears.
Figure 4-9-17: Queuing Counters Page Screenshot
Object Description
 Q0 ~ Q7 There are 8 QoS queues per port. Q0 is the lowest priority queue.
 Rx/Tx The number of received and transmitted packets per queue.
Buttons
4.9.16 Voice VLAN Configuration
The Voice VLAN feature enables voice traffic forwarding on the Voice VLAN, then the switch can classify and schedule network
traffic. It is recommended that there be two VLANs on a port - one for voice, one for data.
Before connecting the IP device to the switch, the IP phone should configure the voice VLAN ID correctly. It should be
configured through its own GUI. The Voice VLAN Configuration screen in Figure 4-9-18 appears.
196
Figure 4-9-18: Voice VLAN Configuration Page Screenshot
Object Description
 Mode Indicates the Voice VLAN mode operation. We must disable MSTP feature
before we enable Voice VLAN. It can avoid the conflict of ingress filter. Possible
modes are:
■ Enabled: Enable Voice VLAN mode operation.
■ Disabled: Disable Voice VLAN mode operation.
 VLAN ID Indicates the Voice VLAN ID. It should be a unique VLAN ID in the system and
cannot equal each port PVID. It is conflict configuration if the value equal
management VID, MVR VID, PVID etc.
The allowed range is 1 to 4095.
 Aging Time Indicates the Voice VLAN secure learning age time. The allowed range is 10 to
10000000 seconds. It used when security mode or auto detect mode is enabled.
In other cases, it will based hardware age time.
The actual age time will be situated in the [age_time; 2 * age_time] interval.
197
 Traffic Class Indicates the Voice VLAN traffic class. All traffic on Voice VLAN will apply this
class.
 Mode Indicates the Voice VLAN port mode.
Possible port modes are:
■ Disabled: Disjoin from Voice VLAN.
■ Auto: Enable auto detect mode. It detects whether there is VoIP

phone attached to the specific port and configures the Voice VLAN
members automatically.
■ Forced: Force join to Voice VLAN.
 Port Security Indicates the Voice VLAN port security mode. When the function is enabled, all
non-telephone MAC address in Voice VLAN will be blocked 10 seconds. Possible
port modes are:
■ Enabled: Enable Voice VLAN security mode operation.
■ Disabled: Disable Voice VLAN security mode operation.
 Port Discovery Indicates the Voice VLAN port discovery protocol. It will only work when auto
Protocol detect mode is enabled. We should enable LLDP feature before configuring
discovery protocol to "LLDP" or "Both". Changing the discovery protocol to "OUI"
or "LLDP" will restart auto detect process. Possible discovery protocols are:
■ OUI: Detect telephony device by OUI address.
■ LLDP: Detect telephony device by LLDP.
■ Both: Both OUI and LLDP.
198
4.9.17 Voice VLAN OUI Table
Configure VOICE VLAN OUI table on this Page. The maximum entry number is 16. Modifying the OUI table will restart auto
detection of OUI process. The Voice VLAN OUI Table screen in Figure 4-9-19 appears.
Figure 4-9-19: Voice VLAN OUI Table Page Screenshot
Object Description
 Telephony OUI An telephony OUI address is a globally unique identifier assigned to a vendor by
IEEE. It must be 6 characters long and the input format is "xx-xx-xx" (x is a
hexadecimal digit).
 Description The description of OUI address. Normally, it describes which vendor telephony
device it belongs to.

The allowed string length is 0 to 32.
Buttons
: Click to add a new access management entry.
199
4.10 Access Control Lists

ACL is an acronym for Access Control List. It is the list table of ACEs, containing access control entries that specify individual
users or groups permitted or denied to specific traffic objects, such as a process or a program.
Each accessible traffic object contains an identifier to its ACL. The privileges determine whether there are specific traffic object
access rights.
ACL implementations can be quite complex, for example, when the ACEs are prioritized for the various situation. In networking,
the ACL refers to a list of service ports or network services that are available on a host or server, each with a list of hosts or
servers permitted or denied to use the service. ACL can generally be configured to control inbound traffic, and in this context,
they are similar to firewalls.
ACE is an acronym for Access Control Entry. It describes access permission associated with a particular ACE ID.
There are three ACE frame types (Ethernet Type, ARP, and IPv4) and two ACE actions (permit and deny). The ACE also
contains many detailed, different parameter options that are available for individual application.
4.10.1 Access Control List Status
This Page shows the ACL status by different ACL users. Each row describes the ACE that is defined. It is a conflict if a specific
ACE is not applied to the hardware due to hardware limitations. The maximum number of ACEs is 512 on each switch. The
Voice VLAN OUI Table screen in Figure 4-10-1 appears.
Figure 4-10-1: ACL Status Page Screenshot
Object Description
 User Indicates the ACL user.
 Ingress Port Indicates the ingress port of the ACE. Possible values are:
■ All: The ACE will match all ingress port.
■ Port: The ACE will match a specific ingress port.
 Frame Type Indicates the frame type of the ACE. Possible values are:
■ Any: The ACE will match any frame type.
■ EType: The ACE will match Ethernet Type frames. Note that an
Ethernet Type based ACE will not get matched by IP and ARP
200
frames.
■ ARP: The ACE will match ARP/RARP frames.
■ IPv4: The ACE will match all IPv4 frames.
■ IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol.
■ IPv4/UDP: The ACE will match IPv4 frames with UDP protocol.
■ IPv4/TCP: The ACE will match IPv4 frames with TCP protocol.
■ IPv4/Other: The ACE will match IPv4 frames, which are not
ICMP/UDP/TCP.
■ IPv6: The ACE will match all IPv6 standard frames.
 Action Indicates the forwarding action of the ACE.
■ Permit: Frames matching the ACE may be forwarded and learned.
■ Deny: Frames matching the ACE are dropped.
 Rate Limiter Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When
Disabled is displayed, the rate limiter operation is disabled.
 Port Redirect Indicates the port redirect operation of the ACE. Frames matching the ACE are
redirected to the port number.
The allowed values are Disabled or a specific port number. When Disabled is
displayed, the port redirect operation is disabled.
 Mirror Specify the mirror operation of this port. The allowed values are:
■ Enabled: Frames received on the port are mirrored.
■ Disabled: Frames received on the port are not mirrored.

The default value is "Disabled".
 CPU Forward packet that matched the specific ACE to CPU.
 CPU Once Forward first packet that matched the specific ACE to CPU.
 Counter The counter indicates the number of times the ACE was hit by a frame.
 Conflict Indicates the hardware status of the specific ACE. The specific ACE is not
applied to the hardware due to hardware limitations.
Buttons
201
4.10.2 Access Control List Configuration
This Page shows the Access Control List (ACL), which is made up of the ACEs defined on this switch. Each row describes the
ACE that is defined. The maximum number of ACEs is 512 on each switch.
Click on the lowest plus sign to add a new ACE to the list. The reserved ACEs used for internal protocol, cannot be edited or
deleted, the order sequence cannot be changed and the priority is highest. The Access Control List Configuration screen in
Figure 4-10-2: Access Control List Configuration Page Screenshot
Object Description
 Ingress Port Indicates the ingress port of the ACE. Possible values are:
■ All: The ACE will match all ingress port.
■ Port: The ACE will match a specific ingress port.
 Policy / Bitmask Indicates the policy number and bitmask of the ACE.
 Frame Type Indicates the frame type of the ACE. Possible values are:
■ Any: The ACE will match any frame type.

■ EType: The ACE will match Ethernet Type frames. Note that an
Ethernet Type based ACE will not get matched by IP and ARP
frames.
■ ARP: The ACE will match ARP/RARP frames.
■ IPv4: The ACE will match all IPv4 frames.
■ IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol.
■ IPv4/UDP: The ACE will match IPv4 frames with UDP protocol.
■ IPv4/TCP: The ACE will match IPv4 frames with TCP protocol.
■ IPv4/Other: The ACE will match IPv4 frames, which are not
ICMP/UDP/TCP.
■ IPv6: The ACE will match all IPv6 standard frames.
 Action Indicates the forwarding action of the ACE.
■ Permit: Frames matching the ACE may be forwarded and learned.
■ Deny: Frames matching the ACE are dropped.
202
 Rate Limiter Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When
Disabled is displayed, the rate limiter operation is disabled.
 Port Redirect Indicates the port redirect operation of the ACE. Frames matching the ACE are
redirected to the port number.
The allowed values are Disabled or a specific port number. When Disabled is
displayed, the port redirect operation is disabled.
 Modification Buttons You can modify each ACE (Access Control Entry) in the table using the following
buttons:
: Inserts a new ACE before the current row.
: Edits the ACE row.
: Moves the ACE up the list.
: Moves the ACE down the list.
: Deletes the ACE.
: The lowest plus sign adds a new entry at the bottom of the ACE listings.
Buttons
: Click to clear the counters.
: Click to remove all ACEs.
203
4.10.3 ACE Configuration
Configure an ACE (Access Control Entry) on this Page. An ACE consists of several parameters. These parameters vary
according to the frame type that you select. First select the ingress port for the ACE, and then select the frame type. Different
parameter options are displayed depending on the frame type selected. A frame that hits this ACE matches the configuration
that is defined here. The ACE Configuration screen in Figure 4-10-3 appears.
Figure 4-10-3: ACE Configuration Page Screenshot
Object Description
 Ingress Port Select the ingress port for which this ACE applies.
■ Any: The ACE applies to any port.
■ Port n: The ACE applies to this port number, where n is the number of the
switch port.
 Policy Filter Specify the policy number filter for this ACE.
■ Any: No policy filter is specified. (policy filter status is "don't-care".)
■ Specific: If you want to filter a specific policy with this ACE, choose this
value. Two field for entering an policy value and bitmask appears.
 Policy Value When "Specific" is selected for the policy filter, you can enter a specific policy value.
 Policy Bitmask When "Specific" is selected for the policy filter, you can enter a specific policy bitmask.
The allowed range is 0x0 to 0xff.
 Frame Type Select the frame type for this ACE. These frame types are mutually exclusive.
■ Any: Any frame can match this ACE.
204
■ Ethernet Type: Only Ethernet Type frames can match this ACE. The IEEE
802.3 describes the value of Length/Type Field specifications to be greater
than or equal to 1536 decimal (equal to 0600 hexadecimal).
■ ARP: Only ARP frames can match this ACE. Notice the ARP frames won't
match the ACE with ethernet type.
■ IPv4: Only IPv4 frames can match this ACE. Notice the IPv4 frames won't
match the ACE with ethernet type.
■ IPv6: Only IPv6 frames can match this ACE. Notice the IPv6 frames won't
match the ACE with ehternet type.
 Action Specify the action to take with a frame that hits this ACE.
■ Permit: The frame that hits this ACE is granted permission for the ACE
operation.
■ Deny: The frame that hits this ACE is dropped.
 Rate Limiter Specify the rate limiter in number of base units.
Disabled indicates that the rate limiter operation is disabled.
 Port Redirect Frames that hit the ACE are redirected to the port number specified here.
The allowed range is the same as the switch port number range.
Disabled indicates that the port redirect operation is disabled.
 Logging Specify the logging operation of the ACE. The allowed values are:
■ Enabled: Frames matching the ACE are stored in the System Log.
■ Disabled: Frames matching the ACE are not logged.
Note: The logging feature only works when the packet length is less than 1518(without
VLAN tags) and the System Log memory size and logging rate is limited.
 Shutdown Specify the port shut down operation of the ACE. The allowed values are:
■ Enabled: If a frame matches the ACE, the ingress port will be disabled.
■ Disabled: Port shut down is disabled for the ACE.
Note: The shutdown feature only works when the packet length is less than
1518(without VLAN tags).
205
 MAC Parameters
Object Description
 SMAC Filter (Only displayed when the frame type is Ethernet Type or ARP.)
Specify the source MAC filter for this ACE.
■ Any: No SMAC filter is specified. (SMAC filter status is "don't-care".)
■ Specific: If you want to filter a specific source MAC address with this ACE,
choose this value. A field for entering an SMAC value appears.
 SMAC Value When "Specific" is selected for the SMAC filter, you can enter a specific source MAC
address. The legal format is "xx-xx-xx-xx-xx-xx" or "xx.xx.xx.xx.xx.xx" or
"xxxxxxxxxxxx" (x is a hexadecimal digit). A frame that hits this ACE matches this
SMAC value.
 DMAC Filter Specify the destination MAC filter for this ACE.
■ Any: No DMAC filter is specified. (DMAC filter status is "don't-care".)
■ MC: Frame must be multicast.
■ BC: Frame must be broadcast.
■ UC: Frame must be unicast.
■ Specific: If you want to filter a specific destination MAC address with this
ACE, choose this value. A field for entering a DMAC value appears.
 DMAC Value When "Specific" is selected for the DMAC filter, you can enter a specific destination
MAC address. The legal format is "xx-xx-xx-xx-xx-xx" or "xx.xx.xx.xx.xx.xx" or
"xxxxxxxxxxxx" (x is a hexadecimal digit). A frame that hits this ACE matches this
DMAC value.
 VLAN Parameters
Object Description
 VLAN ID Filter Specify the VLAN ID filter for this ACE.
■ Any: No VLAN ID filter is specified. (VLAN ID filter status is "don't-care".)
■ Specific: If you want to filter a specific VLAN ID with this ACE, choose this
value. A field for entering a VLAN ID number appears.
 VLAN ID When "Specific" is selected for the VLAN ID filter, you can enter a specific VLAN ID
number. The allowed range is 1 to 4095. A frame that hits this ACE matches this VLAN
ID value.
 Tag Priority Specify the tag priority for this ACE. A frame that hits this ACE matches this tag priority.
The allowed number range is 0 to 7. The value Any means that no tag priority is
specified (tag priority is "don't-care".)
206
 ARP Parameters
The ARP parameters can be configured when Frame Type "ARP" is selected.
Object Description
 ARP/RARP Specify the available ARP/RARP opcode (OP) flag for this ACE.
■ Any: No ARP/RARP OP flag is specified. (OP is "don't-care".)
■ ARP: Frame must have ARP/RARP opcode set to ARP.
■ RARP: Frame must have ARP/RARP opcode set to RARP.
■ Other: Frame has unknown ARP/RARP Opcode flag.
 Request/Reply Specify the available ARP/RARP opcode (OP) flag for this ACE.
■ Any: No ARP/RARP OP flag is specified. (OP is "don't-care".)
■ Request: Frame must have ARP Request or RARP Request OP flag set.
■ Reply: Frame must have ARP Reply or RARP Reply OP flag.
 Sender IP Filter Specify the sender IP filter for this ACE.
■ Any: No sender IP filter is specified. (Sender IP filter is "don't-care".)
■ Host: Sender IP filter is set to Host. Specify the sender IP address in the
SIP Address field that appears.
■ Network: Sender IP filter is set to Network. Specify the sender IP address

and sender IP mask in the SIP Address and SIP Mask fields that appear.
 Sender IP Address When "Host" or "Network" is selected for the sender IP filter, you can enter a
specific sender IP address in dotted decimal notation.
 Sender IP Mask When "Network" is selected for the sender IP filter, you can enter a specific
sender IP mask in dotted decimal notation.
 Target IP Filter Specify the target IP filter for this specific ACE.
■ Any: No target IP filter is specified. (Target IP filter is "don't-care".)
■ Host: Target IP filter is set to Host. Specify the target IP address in the
Target IP Address field that appears.
■ Network: Target IP filter is set to Network. Specify the target IP address

and target IP mask in the Target IP Address and Target IP Mask fields that
appear.
 Target IP Address When "Host" or "Network" is selected for the target IP filter, you can enter a
specific target IP address in dotted decimal notation.
 Target IP Mask When "Network" is selected for the target IP filter, you can enter a specific target
IP mask in dotted decimal notation.
 ARP Sender MAC Specify whether frames can hit the action according to their sender hardware
Match address field (SHA) settings.
■ 0: ARP frames where SHA is not equal to the SMAC address.
■ 1: ARP frames where SHA is equal to the SMAC address.
■ Any: Any value is allowed ("don't-care").
207
 RARP Target MAC Specify whether frames can hit the action according to their target hardware
Match address field (THA) settings.
■ 0: RARP frames where THA is not equal to the SMAC address.
■ 1: RARP frames where THA is equal to the SMAC address.
 IP/Ethernet Length Specify whether frames can hit the action according to their ARP/RARP
hardware address length (HLN) and protocol address length (PLN) settings.
■ 0: ARP/RARP frames where the HLN is equal to Ethernet (0x06) and the
(PLN) is equal to IPv4 (0x04).
■ 1: ARP/RARP frames where the HLN is equal to Ethernet (0x06) and the
(PLN) is equal to IPv4 (0x04).
 IP Specify whether frames can hit the action according to their ARP/RARP
hardware address space (HRD) settings.
■ 0: ARP/RARP frames where the HLD is equal to Ethernet (1).
■ 1: ARP/RARP frames where the HLD is equal to Ethernet (1).
 Ethernet Specify whether frames can hit the action according to their ARP/RARP protocol
address space (PRO) settings.
■ 0: ARP/RARP frames where the PRO is equal to IP (0x800).
■ 1: ARP/RARP frames where the PRO is equal to IP (0x800).
 IP Parameters
The IP parameters can be configured when Frame Type "IPv4" is selected.
Object Description
 IP Protocol Filter Specify the IP protocol filter for this ACE.
■ Any: No IP protocol filter is specified ("don't-care").
■ Specific: If you want to filter a specific IP protocol filter with this ACE,
choose this value. A field for entering an IP protocol filter appears.
■ ICMP: Select ICMP to filter IPv4 ICMP protocol frames. Extra fields for
defining ICMP parameters will appear. These fields are explained later in
this help file.
■ UDP: Select UDP to filter IPv4 UDP protocol frames. Extra fields for
defining UDP parameters will appear. These fields are explained later in
this help file.
■ TCP: Select TCP to filter IPv4 TCP protocol frames. Extra fields for defining
TCP parameters will appear. These fields are explained later in this help
file.
208
 IP Protocol Value When "Specific" is selected for the IP protocol value, you can enter a specific
value. The allowed range is 0 to 255. A frame that hits this ACE matches this IP
protocol value.
 IP TTL Specify the Time-to-Live settings for this ACE.
■ zero: IPv4 frames with a Time-to-Live field greater than zero must not be
able to match this entry.
■ non-zero: IPv4 frames with a Time-to-Live field greater than zero must be
able to match this entry.
 IP Fragment Specify the fragment offset settings for this ACE. This involves the settings for the
More Fragments (MF) bit and the Fragment Offset (FRAG OFFSET) field for an
IPv4 frame.
■ No: IPv4 frames where the MF bit is set or the FRAG OFFSET field is
greater than zero must not be able to match this entry.
■ Yes: IPv4 frames where the MF bit is set or the FRAG OFFSET field is
greater than zero must be able to match this entry.
 IP Option Specify the options flag setting for this ACE.
■ No: IPv4 frames where the options flag is set must not be able to match
this entry.
■ Yes: IPv4 frames where the options flag is set must be able to match this
entry.
 SIP Filter Specify the source IP filter for this ACE.
■ Any: No source IP filter is specified. (Source IP filter is "don't-care".)
■ Host: Source IP filter is set to Host. Specify the source IP address in the
SIP Address field that appears.
■ Network: Source IP filter is set to Network. Specify the source IP address

and source IP mask in the SIP Address and SIP Mask fields that appear.
 SIP Address When "Host" or "Network" is selected for the source IP filter, you can enter a
specific SIP address in dotted decimal notation.
 SIP Mask When "Network" is selected for the source IP filter, you can enter a specific SIP
mask in dotted decimal notation.
 DIP Filter Specify the destination IP filter for this ACE.
■ Any: No destination IP filter is specified. (Destination IP filter is

"don't-care".)
■ Host: Destination IP filter is set to Host. Specify the destination IP address

in the DIP Address field that appears.
■ Network: Destination IP filter is set to Network. Specify the destination IP

address and destination IP mask in the DIP Address and DIP Mask fields
209
that appear.
 DIP Address When "Host" or "Network" is selected for the destination IP filter, you can enter a
specific DIP address in dotted decimal notation.
 DIP Mask When "Network" is selected for the destination IP filter, you can enter a specific
DIP mask in dotted decimal notation.
 IPv6 Parameters
Object Description
 Next Header Fliter Specify the IPv6 next header filter for this ACE.
■ Any: No IPv6 next header filter is specified ("don't-care").
■ Specific: If you want to filter a specific IPv6 next header filter with this
ACE, choose this value. A field for entering an IPv6 next header filter
appears.
■ ICMP: Select ICMP to filter IPv6 ICMP protocol frames. Extra fields for
defining ICMP parameters will appear. These fields are explained later in
this help file.
■ UDP: Select UDP to filter IPv6 UDP protocol frames. Extra fields for
defining UDP parameters will appear. These fields are explained later in
this help file.
■ TCP: Select TCP to filter IPv6 TCP protocol frames. Extra fields for defining
TCP parameters will appear. These fields are explained later in this help
file.
 Next Header Value When "Specific" is selected for the IPv6 next header value, you can enter a
specific value. The allowed range is 0 to 255. A frame that hits this ACE matches
this IPv6 protocol value.
 SIP Filter Specify the source IPv6 filter for this ACE.
■ Any: No source IPv6 filter is specified. (Source IPv6 filter is "don't-care".)
■ Specific: Source IPv6 filter is set to Network. Specify the source IPv6
address and source IPv6 mask in the SIP Address fields that appear.
 SIP Address When "Specific" is selected for the source IPv6 filter, you can enter a specific
SIPv6 address. The field only supported last 32 bits for IPv6 address.
 SIP BitMask When "Specific" is selected for the source IPv6 filter, you can enter a specific
SIPv6 mask. The field only supported last 32 bits for IPv6 address. Notice the
usage of bitmask, if the binary bit value is "0", it means this bit is "don't-care".
The real matched pattern is [sipv6_address & sipv6_bitmask] (last 32 bits). For
example, if the SIPv6 address is 2001::3 and the SIPv6 bitmask is
0xFFFFFFFE(bit 0 is "don't-care" bit), then SIPv6 address 2001::2 and 2001::3
are applied to this rule.
210
 Hop Limit Specify the hop limit settings for this ACE.
■ zero: IPv6 frames with a hop limit field greater than zero must not be able
to match this entry.
■ non-zero: IPv6 frames with a hop limit field greater than zero must be able
to match this entry.
■ Any: Any value is allowed ("don't-care”).
 ICMP Parameters
Object Description
 ICMP Type Filter Specify the ICMP filter for this ACE.
■ Any: No ICMP filter is specified (ICMP filter status is "don't-care").
■ Specific: If you want to filter a specific ICMP filter with this ACE, you can
enter a specific ICMP value. A field for entering an ICMP value appears.
 ICMP Type Value When "Specific" is selected for the ICMP filter, you can enter a specific ICMP
value.
The allowed range is 0 to 255. A frame that hits this ACE matches this ICMP
value.
 ICMP Code Filter Specify the ICMP code filter for this ACE.
■ Any: No ICMP code filter is specified (ICMP code filter status is

"don't-care").
■ Specific: If you want to filter a specific ICMP code filter with this ACE, you
can enter a specific ICMP code value. A field for entering an ICMP code
value appears.
 ICMP Code Value When "Specific" is selected for the ICMP code filter, you can enter a specific
ICMP code value.

The allowed range is 0 to 255. A frame that hits this ACE matches this ICMP
code value.
 TCP/UDP Parameters
Object Description
 TCP/UDP Source Filter Specify the TCP/UDP source filter for this ACE.
■ Any: No TCP/UDP source filter is specified (TCP/UDP source filter status

is "don't-care").
■ Specific: If you want to filter a specific TCP/UDP source filter with this
ACE, you can enter a specific TCP/UDP source value. A field for entering a
TCP/UDP source value appears.
211
■ Range: If you want to filter a specific TCP/UDP source range filter with this
ACE, you can enter a specific TCP/UDP source range value. A field for
entering a TCP/UDP source value appears.
 TCP/UDP Source No. When "Specific" is selected for the TCP/UDP source filter, you can enter a
specific TCP/UDP source value. The allowed range is 0 to 65535. A frame that
hits this ACE matches this TCP/UDP source value.
 TCP/UDP Source When "Range" is selected for the TCP/UDP source filter, you can enter a specific
Range TCP/UDP source range value. The allowed range is 0 to 65535. A frame that hits
this ACE matches this TCP/UDP source value.
 TCP/UDP Destination Specify the TCP/UDP destination filter for this ACE.
Filter ■ Any: No TCP/UDP destination filter is specified (TCP/UDP destination filter

status is "don't-care").
■ Specific: If you want to filter a specific TCP/UDP destination filter with this
ACE, you can enter a specific TCP/UDP destination value. A field for
entering a TCP/UDP destination value appears.
■ Range: If you want to filter a specific range TCP/UDP destination filter with
this ACE, you can enter a specific TCP/UDP destination range value. A
field for entering a TCP/UDP destination value appears.
 TCP/UDP Destination When "Specific" is selected for the TCP/UDP destination filter, you can enter a
Number specific TCP/UDP destination value. The allowed range is 0 to 65535. A frame
that hits this ACE matches this TCP/UDP destination value.
 TCP/UDP Destination When "Range" is selected for the TCP/UDP destination filter, you can enter a
Range specific TCP/UDP destination range value. The allowed range is 0 to 65535. A
frame that hits this ACE matches this TCP/UDP destination value.
 TCP FIN Specify the TCP "No more data from sender" (FIN) value for this ACE.
■ 0: TCP frames where the FIN field is set must not be able to match this
entry.
■ 1: TCP frames where the FIN field is set must be able to match this entry.
 TCP SYN Specify the TCP "Synchronize sequence numbers" (SYN) value for this ACE.
■ 0: TCP frames where the SYN field is set must not be able to match this
entry.
■ 1: TCP frames where the SYN field is set must be able to match this entry.
 TCP RST Specify the TCP "Reset the connection" (RST) value for this ACE.
■ 0: TCP frames where the RST field is set must not be able to match this
entry.
■ 1: TCP frames where the RST field is set must be able to match this entry.
212
 TCP PSH Specify the TCP "Push Function" (PSH) value for this ACE.
■ 0: TCP frames where the PSH field is set must not be able to match this
entry.
■ 1: TCP frames where the PSH field is set must be able to match this entry.
 TCP ACK Specify the TCP "Acknowledgment field significant" (ACK) value for this ACE.
■ 0: TCP frames where the ACK field is set must not be able to match this
entry.
■ 1: TCP frames where the ACK field is set must be able to match this entry.
 TCP URG Specify the TCP "Urgent Pointer field significant" (URG) value for this ACE.
■ 0: TCP frames where the URG field is set must not be able to match this
entry.
■ 1: TCP frames where the URG field is set must be able to match this entry.
 Ethernet Type Parameters
The Ethernet Type parameters can be configured when Frame Type "Ethernet Type" is selected.
Object Description
 EtherType Filter Specify the Ethernet type filter for this ACE.
■ Any: No EtherType filter is specified (EtherType filter status is

"don't-care").
■ Specific: If you want to filter a specific EtherType filter with this ACE,
you can enter a specific EtherType value. A field for entering a
EtherType value appears.
 Ethernet Type Value When "Specific" is selected for the EtherType filter, you can enter a specific
EtherType value.
The allowed range is 0x600 to 0xFFFF but excluding 0x800(IPv4), 0x806(ARP)

and 0x86DD(IPv6). A frame that hits this ACE matches this EtherType value.
Buttons
: Return to the previous Page.
213
4.10.4 ACL Ports Configuration
Configure the ACL parameters (ACE) of each switch port. These parameters will affect frames received on a port unless the
frame matches a specific ACE. The ACL Ports Configuration screen in Figure 4-10-4 appears.
Figure 4-10-4: ACL Ports Configuration Page Screenshot
Object Description
 Policy ID Select the policy to apply to this port. The allowed values are 0 through 255.
 Action Select whether forwarding is permitted ("Permit") or denied ("Deny").
The default value is "Permit".
 Rate Limiter ID Select which rate limiter to apply on this port. The allowed values are Disabled or
the values 1 through 16.

 Port Redirect Select which port frames are redirected on. The allowed values are Disabled or a
specific port number and it can't be set when action is permitted. The default
value is "Disabled".
 Logging Specify the logging operation of this port. The allowed values are:
■ Enabled: Frames received on the port are stored in the System Log.
■ Disabled: Frames received on the port are not logged.

Please note that the System Log memory size and logging rate are limited.
 Shutdown Specify the port shut down operation of this port. The allowed values are:
■ Enabled: If a frame is received on the port, the port will be disabled.
214
■ Disabled: Port shut down is disabled.

 State Specify the port state of this port. The allowed values are:
■ Enabled: To reopen ports by changing the volatile port configuration of the

ACL user module.
■ Disabled: To close ports by changing the volatile port configuration of the

ACL user module.
The default value is "Enabled".
 Counter Counts the number of frames that match this ACE.
Buttons
: Click to clear the counters.
215
4.10.5 ACL Rate Limiter Configuration
Configure the rate limiter for the ACL of the switch.
The ACL Rate Limiter Configuration screen in Figure 4-10-5 appears.
Figure 4-10-5: ACL Rate Limiter Configuration Page Screenshot
Object Description
 Rate Limiter ID The rate limiter ID for the settings contained in the same row.
 Rate (pps) The allowed values are: 0-3276700 in pps or 0, 100, 200, 300, ..., 1000000 in
kbps.
Buttons
216
4.11 Authentication
This section is to control the access of the Managed Switch, includes the user access and management control.
The Authentication section contains links to the following main topics:
 IEEE 802.1X Port-Based Network Access Control
 MAC-Based Authentication
 User Authentication
Overview of 802.1X (Port-Based) Authentication
In the 802.1X-world, the user is called the supplicant, the switch is the authenticator, and the RADIUS server is the
authentication server. The switch acts as the man-in-the-middle, forwarding requests and responses between the supplicant
and the authentication server. Frames sent between the supplicant and the switch are special 802.1X frames, known as EAPOL
(EAP Over LANs) frames. EAPOL frames encapsulate EAP PDUs (RFC3748). Frames sent between the switch and the
RADIUS server are RADIUS packets. RADIUS packets also encapsulate EAP PDUs together with other attributes like the
switch's IP address, name, and the supplicant's port number on the switch. EAP is very flexible, in that it allows for different
authentication methods, like MD5-Challenge, PEAP, and TLS. The important thing is that the authenticator (the switch) doesn't
need to know which authentication method the supplicant and the authentication server are using, or how many information
exchange frames are needed for a particular method. The switch simply encapsulates the EAP part of the frame into the
relevant type (EAPOL or RADIUS) and forwards it.
When authentication is complete, the RADIUS server sends a special packet containing a success or failure indication. Besides
forwarding this decision to the supplicant, the switch uses it to open up or block traffic on the switch port connected to the
supplicant.
Overview of MAC-Based Authentication

Unlike 802.1X, MAC-based authentication is not a standard, but merely a best-practices method adopted by the industry. In
MAC-based authentication, users are called clients, and the switch acts as the supplicant on behalf of clients. The initial frame
(any kind of frame) sent by a client is snooped by the switch, which in turn uses the client's MAC address as both username and
password in the subsequent EAP exchange with the RADIUS server. The 6-byte MAC address is converted to a string on the
following form "xx-xx-xx-xx-xx-xx", that is, a dash (-) is used as separator between the lower-cased hexadecimal digits. The
switch only supports the MD5-Challenge authentication method, so the RADIUS server must be configured accordingly.
When authentication is complete, the RADIUS server sends a success or failure indication, which in turn causes the switch to
open up or block traffic for that particular client, using static entries into the MAC Table. Only then will frames from the client be
forwarded on the switch. There are no EAPOL frames involved in this authentication, and therefore, MAC-based Authentication
has nothing to do with the 802.1X standard.
The advantage of MAC-based authentication over 802.1X is that several clients can be connected to the same port (e.g. through
a 3rd party switch or a hub) and still require individual authentication, and that the clients don't need special supplicant software
217
to authenticate. The disadvantage is that MAC addresses can be spoofed by malicious users, equipment whose MAC address
is a valid RADIUS user can be used by anyone, and only the MD5-Challenge method is supported.
The 802.1X and MAC-Based Authentication configuration consists of two sections, a system- and a port-wide.
Overview of User Authentication

It is allowed to configure the Managed Switch to authenticate users logging into the system for management access using local
or remote authentication methods, such as telnet and Web browser. This Managed Switch provides secure network
management access using the following options:
 Remote Authentication Dial-in User Service (RADIUS)
 Terminal Access Controller Access Control System Plus (TACACS+)
 Local user name and Priviledge Level control
RADIUS and TACACS+ are logon authentication protocols that use software running on a central server to control access to
RADIUS-aware or TACACS-aware devices on the network. An authentication server contains a database of multiple user
name / password pairs with associated privilege levels for each user that requires management access to the Managed Switch.
4.11.1 Understanding IEEE 802.1X Port-Based Authentication
The IEEE 802.1X standard defines a client-server-based access control and authentication protocol that restricts unauthorized
clients from connecting to a LAN through publicly accessible ports. The authentication server authenticates each client
connected to a switch port before making available any services offered by the switch or the LAN.
Until the client is authenticated, 802.1X access control allows only Extensible Authentication Protocol over LAN (EAPOL)
traffic through the port to which the client is connected. After authentication is successful, normal traffic can pass through the
port.
This section includes this conceptual information:
 Device Roles
 Authentication Initiation and Message Exchange
 Ports in Authorized and Unauthorized States
 Device Roles
With 802.1X port-based authentication, the devices in the network have specific roles as shown below.
218
Figure 4-11-1
 Client—the device (workstation) that requests access to the LAN and switch services and responds to requests from
the switch. The workstation must be running 802.1X-compliant client software such as that offered in the Microsoft
Windows XP operating system. (The client is the supplicant in the IEEE 802.1X specification.)
 Authentication server—performs the actual authentication of the client. The authentication server validates the
identity of the client and notifies the switch whether or not the client is authorized to access the LAN and switch services.
Because the switch acts as the proxy, the authentication service is transparent to the client. In this release, the Remote
Authentication Dial-In User Service (RADIUS) security system with Extensible Authentication Protocol (EAP)
extensions is the only supported authentication server; it is available in Cisco Secure Access Control Server version 3.0.
RADIUS operates in a client/server model in which secure authentication information is exchanged between the
RADIUS server and one or more RADIUS clients.
 Switch (802.1X device)—controls the physical access to the network based on the authentication status of the client.
The switch acts as an intermediary (proxy) between the client and the authentication server, requesting identity
information from the client, verifying that information with the authentication server, and relaying a response to the client.
The switch includes the RADIUS client, which is responsible for encapsulating and decapsulating the Extensible
Authentication Protocol (EAP) frames and interacting with the authentication server. When the switch receives EAPOL
frames and relays them to the authentication server, the Ethernet header is stripped and the remaining EAP frame is
re-encapsulated in the RADIUS format. The EAP frames are not modified or examined during encapsulation, and the
authentication server must support EAP within the native frame format. When the switch receives frames from the
219
authentication server, the server's frame header is removed, leaving the EAP frame, which is then encapsulated for
Ethernet and sent to the client.
 Authentication Initiation and Message Exchange
The switch or the client can initiate authentication. If you enable authentication on a port by using the dot1x port-control auto
interface configuration command, the switch must initiate authentication when it determines that the port link state transitions
from down to up. It then sends an EAP-request/identity frame to the client to request its identity (typically, the switch sends an
initial identity/request frame followed by one or more requests for authentication information). Upon receipt of the frame, the
client responds with an EAP-response/identity frame.
However, if during bootup, the client does not receive an EAP-request/identity frame from the switch, the client can initiate
authentication by sending an EAPOL-start frame, which prompts the switch to request the client's identity
If 802.1X is not enabled or supported on the network access device, any EAPOL frames from the
client are dropped. If the client does not receive an EAP-request/identity frame after three attempts
to start authentication, the client transmits frames as if the port is in the authorized state. A port in
the authorized state effectively means that the client has been successfully authenticated.
When the client supplies its identity, the switch begins its role as the intermediary, passing EAP frames between the client and
the authentication server until authentication succeeds or fails. If the authentication succeeds, the switch port becomes
authorized.
The specific exchange of EAP frames depends on the authentication method being used. “Figure 4-11-2” shows a message
exchange initiated by the client using the One-Time-Password (OTP) authentication method with a RADIUS server.
Figure 4-11-2: EAP Message Exchange
220
 Ports in Authorized and Unauthorized States

The switch port state determines whether or not the client is granted access to the network. The port starts in the unauthorized
state. While in this state, the port disallows all ingress and egress traffic except for 802.1X protocol packets. When a client is
successfully authenticated, the port transitions to the authorized state, allowing all traffic for the client to flow normally.
If a client that does not support 802.1X is connected to an unauthorized 802.1X port, the switch requests the client's identity. In
this situation, the client does not respond to the request, the port remains in the unauthorized state, and the client is not granted
access to the network.
In contrast, when an 802.1X-enabled client connects to a port that is not running the 802.1X protocol, the client initiates the
authentication process by sending the EAPOL-start frame. When no response is received, the client sends the request for a
fixed number of times. Because no response is received, the client begins sending frames as if the port is in the authorized state
If the client is successfully authenticated (receives an Accept frame from the authentication server), the port state changes to
authorized, and all frames from the authenticated client are allowed through the port. If the authentication fails, the port remains
in the unauthorized state, but authentication can be retried. If the authentication server cannot be reached, the switch can
retransmit the request. If no response is received from the server after the specified number of attempts, authentication fails,
and network access is not granted.
When a client logs off, it sends an EAPOL-logoff message, causing the switch port to transition to the unauthorized state.
If the link state of a port transitions from up to down, or if an EAPOL-logoff frame is received, the port returns to the unauthorized
state.
4.11.2 Authentication Configuration
This Page allows you to configure how a user is authenticated when he logs into the switch via one of the management client
interfaces. The Authentication Method Configuration screen in Figure 4-11-3 appears.
Figure 4-11-3: Authentication Method Configuration Page Screenshot
221
Object Description
 Client The management client for which the configuration below applies.
 Authentication Method Authentication Method can be set to one of the following values:
■ None: authentication is disabled and login is not possible.
■ Local: use the local user database on the switch for authentication.
■ RADIUS: use a remote RADIUS server for authentication.
■ TACACS+: use a remote TACACS+ server for authentication.
Methods that involves remote servers are timed out if the remote servers are
offline. In this case the next method is tried. Each method is tried from left to right
and continues until a method either approves or rejects a user. If a remote server
is used for primary authentication it is recommended to configure secondary
authentication as 'local'. This will enable the management client to login via the
local user database if none of the configured authentication servers are alive.
Buttons
4.11.3 Network Access Server Configuration
This Page allows you to configure the IEEE 802.1X and MAC-based authentication system and port settings.
The IEEE 802.1X standard defines a port-based access control procedure that prevents unauthorized access to a network by
requiring users to first submit credentials for authentication. One or more central servers, the backend servers, determine
whether the user is allowed access to the network. These backend (RADIUS) servers are configured on the
"Configuration→Security→AAA" Page. The IEEE802.1X standard defines port-based operation, but non-standard variants
overcome security limitations as shall be explored below.
MAC-based authentication allows for authentication of more than one user on the same port, and doesn't require the user to
have special 802.1X supplicant software installed on his system. The switch uses the user's MAC address to authenticate
against the backend server. Intruders can create counterfeit MAC addresses, which makes MAC-based authentication less
secure than 802.1X authentication. The NAS configuration consists of two sections, a system- and a port-wide. The Network
Access Server Configuration screen in Figure 4-11-4 appears.
222
Figure 4-11-4: Network Access Server Configuration Page Screenshot
System Configuration
Object Description
 Mode Indicates if NAS is globally enabled or disabled on the switch. If globally disabled,
all ports are allowed forwarding of frames.
 Reauthentication If checked, successfully authenticated supplicants/clients are reauthenticated
Enabled after the interval specified by the Reauthentication Period. Reauthentication for
802.1X-enabled ports can be used to detect if a new device is plugged into a
switch port or if a supplicant is no longer attached.
For MAC-based ports, reauthentication is only useful if the RADIUS server
configuration has changed. It does not involve communication between the
223
switch and the client, and therefore doesn't imply that a client is still present on a
port.
 Reauthentication Determines the period, in seconds, after which a connected client must be
Period reauthenticated. This is only active if the Reauthentication Enabled checkbox is
checked. Valid values are in the range 1 to 3600 seconds.
 EAPOL Timeout Determines the time for retransmission of Request Identity EAPOL frames.
Valid values are in the range 1 to 65535 seconds. This has no effect for
MAC-based ports.
 Aging Period This setting applies to the following modes, i.e. modes using the Port Security
functionality to secure MAC addresses:
■ Single 802.1X
■ Multi 802.1X
■ MAC-Based Auth.
When the NAS module uses the Port Security module to secure MAC addresses,
the Port Security module needs to check for activity on the MAC address in
question at regular intervals and free resources if no activity is seen within a
given period of time. This parameter controls exactly this period and can be set to
a number between 10 and 1000000 seconds.
If reauthentication is enabled and the port is in a 802.1X-based mode, this is not
so criticial, since supplicants that are no longer attached to the port will get
removed upon the next reauthentication, which will fail. But if reauthentication is
not enabled, the only way to free resources is by aging the entries.
For ports in MAC-based Auth. mode, reauthentication doesn't cause direct
communication between the switch and the client, so this will not detect whether
the client is still attached or not, and the only way to free any resources is to age
the entry.
 Hold Time This setting applies to the following modes, i.e. modes using the Port Security
functionality to secure MAC addresses:
■ Single 802.1X
■ Multi 802.1X
■ MAC-Based Auth.
If a client is denied access - either because the RADIUS server denies the client
access or because the RADIUS server request times out (according to the
timeout specified on the "Configuration→Security→AAA" Page) - the client is put
on hold in the Unauthorized state. The hold timer does not count during an
on-going authentication.
In MAC-based Auth. mode, the The switch will ignore new frames coming from
224
the client during the hold time.
The Hold Time can be set to a number between 10 and 1000000 seconds.
 RADIUS-Assigned QoS RADIUS-assigned QoS provides a means to centrally control the traffic class to
Enabled which traffic coming from a successfully authenticated supplicant is assigned on
the switch. The RADIUS server must be configured to transmit special RADIUS
attributes to take advantage of this feature.
The "RADIUS-Assigned QoS Enabled" checkbox provides a quick way to
globally enable/disable RADIUS-server assigned QoS Class functionality. When
checked, the individual ports' ditto setting determine whether RADIUS-assigned
QoS Class is enabled for that port. When unchecked, RADIUS-server assigned
QoS Class is disabled for all ports.
 RADIUS-Assigned RADIUS-assigned VLAN provides a means to centrally control the VLAN on
VLAN Enabled which a successfully authenticated supplicant is placed on the switch. Incoming
traffic will be classified to and switched on the RADIUS-assigned VLAN. The
RADIUS server must be configured to transmit special RADIUS attributes to take
advantage of this feature.
The "RADIUS-Assigned VLAN Enabled" checkbox provides a quick way to
globally enable/disable RADIUS-server assigned VLAN functionality. When
checked, the individual ports' ditto setting determine whether RADIUS-assigned
VLAN is enabled for that port. When unchecked, RADIUS-server assigned VLAN
is disabled for all ports.
 Guest VLAN Enabled A Guest VLAN is a special VLAN - typically with limited network access - on
which 802.1X-unaware clients are placed after a network administrator-defined
timeout. The switch follows a set of rules for entering and leaving the Guest
VLAN as listed below.
The "Guest VLAN Enabled" checkbox provides a quick way to globally
enable/disable Guest VLAN functionality. When checked, the individual ports'
ditto setting determines whether the port can be moved into Guest VLAN. When
unchecked, the ability to move to the Guest VLAN is disabled for all ports.
 Guest VLAN ID This is the value that a port's Port VLAN ID is set to if a port is moved into the
Guest VLAN. It is only changeable if the Guest VLAN option is globally enabled.
Valid values are in the range [1; 4095].
 Max. Reauth. Count The number of times that the switch transmits an EAPOL Request Identity frame
without response before considering entering the Guest VLAN is adjusted with
this setting. The value can only be changed if the Guest VLAN option is globally
225
enabled.
Valid values are in the range [1; 255].
 Allow Guest VLAN if The switch remembers if an EAPOL frame has been received on the port for the
EAPOL Seen life-time of the port. Once the switch considers whether to enter the Guest VLAN,
it will first check if this option is enabled or disabled. If disabled (unchecked;
default), the switch will only enter the Guest VLAN if an EAPOL frame has not
been received on the port for the life-time of the port. If enabled (checked), the
switch will consider entering the Guest VLAN even if an EAPOL frame has been
received on the port for the life-time of the port.
The value can only be changed if the Guest VLAN option is globally enabled.
Port Configuration
The table has one row for each port and a number of columns, which are:
Object Description
 Admin State If NAS is globally enabled, this selection controls the port's authentication mode.
The following modes are available:
Force Authorized
In this mode, the switch will send one EAPOL Success frame when the port link
comes up, and any client on the port will be allowed network access without
authentication.
Force Unauthorized
In this mode, the switch will send one EAPOL Failure frame when the port link
comes up, and any client on the port will be disallowed network access.
Port-based 802.1X
In the 802.1X-world, the user is called the supplicant, the switch is the
authenticator, and the RADIUS server is the authentication server. The
authenticator acts as the man-in-the-middle, forwarding requests and responses
between the supplicant and the authentication server. Frames sent between the
supplicant and the switch are special 802.1X frames, known as EAPOL (EAP
Over LANs) frames. EAPOL frames encapsulate EAP PDUs (RFC3748). Frames
sent between the switch and the RADIUS server are RADIUS packets. RADIUS
226
packets also encapsulate EAP PDUs together with other attributes like the
switch's IP address, name, and the supplicant's port number on the switch. EAP
is very flexible, in that it allows for different authentication methods, like
MD5-Challenge, PEAP, and TLS. The important thing is that the authenticator
(the switch) doesn't need to know which authentication method the supplicant
and the authentication server are using, or how many information exchange
frames are needed for a particular method. The switch simply encapsulates the
EAP part of the frame into the relevant type (EAPOL or RADIUS) and forwards it.
When authentication is complete, the RADIUS server sends a special packet
containing a success or failure indication. Besides forwarding this decision to the
supplicant, the switch uses it to open up or block traffic on the switch port
connected to the supplicant.
Note: Suppose two backend servers are enabled and that the server timeout is
configured to X seconds (using the AAA configuration Page), and suppose that
the first server in the list is currently down (but not considered dead). Now, if the
supplicant retransmits EAPOL Start frames at a rate faster than X seconds, then
it will never get authenticated, because the switch will cancel on-going backend
authentication server requests whenever it receives a new EAPOL Start frame
from the supplicant. And since the server hasn't yet failed (because the X
seconds haven't expired), the same server will be contacted upon the next
backend authentication server request from the switch. This scenario will loop
forever. Therefore, the server timeout should be smaller than the supplicant's
EAPOL Start frame retransmission rate.
Single 802.1X
In port-based 802.1X authentication, once a supplicant is successfully
authenticated on a port, the whole port is opened for network traffic. This allows
other clients connected to the port (for instance through a hub) to piggy-back on
the successfully authenticated client and get network access even though they
really aren't authenticated. To overcome this security breach, use the Single
802.1X variant.
Single 802.1X is really not an IEEE standard, but features many of the same
characteristics as does port-based 802.1X. In Single 802.1X, at most one
supplicant can get authenticated on the port at a time. Normal EAPOL frames are
used in the communication between the supplicant and the switch. If more than
one supplicant is connected to a port, the one that comes first when the port's link
comes up will be the first one considered. If that supplicant doesn't provide valid
credentials within a certain amount of time, another supplicant will get a chance.
Once a supplicant is successfully authenticated, only that supplicant will be
227
allowed access. This is the most secure of all the supported modes. In this mode,
the Port Security module is used to secure a supplicant's MAC address once
successfully authenticated.
Multi 802.1X
Multi 802.1X is - like Single 802.1X - not an IEEE standard, but a variant that
features many of the same characteristics. In Multi 802.1X, one or more
supplicants can get authenticated on the same port at the same time. Each
supplicant is authenticated individually and secured in the MAC table using the
Port Security module.
In Multi 802.1X it is not possible to use the multicast BPDU MAC address as
destination MAC address for EAPOL frames sent from the switch towards the
supplicant, since that would cause all supplicants attached to the port to reply to
requests sent from the switch. Instead, the switch uses the supplicant's MAC
address, which is obtained from the first EAPOL Start or EAPOL Response
Identity frame sent by the supplicant. An exception to this is when no supplicants
are attached. In this case, the switch sends EAPOL Request Identity frames
using the BPDU multicast MAC address as destination - to wake up any
supplicants that might be on the port.
The maximum number of supplicants that can be attached to a port can be
limited using the Port Security Limit Control functionality.
MAC-based Auth.
Unlike port-based 802.1X, MAC-based authentication is not a standard, but
merely a best-practices method adopted by the industry. In MAC-based
authentication, users are called clients, and the switch acts as the supplicant on
behalf of clients. The initial frame (any kind of frame) sent by a client is snooped
by the switch, which in turn uses the client's MAC address as both username and
password in the subsequent EAP exchange with the RADIUS server. The 6-byte
MAC address is converted to a string on the following form "xx-xx-xx-xx-xx-xx",
that is, a dash (-) is used as separator between the lower-cased hexadecimal
digits. The switch only supports the MD5-Challenge authentication method, so
the RADIUS server must be configured accordingly.
When authentication is complete, the RADIUS server sends a success or failure
indication, which in turn causes the switch to open up or block traffic for that
particular client, using the Port Security module. Only then will frames from the
client be forwarded on the switch. There are no EAPOL frames involved in this
authentication, and therefore, MAC-based Authentication has nothing to do with
228
the 802.1X standard.
The advantage of MAC-based authentication over port-based 802.1X is that
several clients can be connected to the same port (e.g. through a 3rd party
switch or a hub) and still require individual authentication, and that the clients
don't need special supplicant software to authenticate. The advantage of
MAC-based authentication over 802.1X-based authentication is that the clients
don't need special supplicant software to authenticate. The disadvantage is that
MAC addresses can be spoofed by malicious users - equipment whose MAC
address is a valid RADIUS user can be used by anyone. Also, only the
MD5-Challenge method is supported. The maximum number of clients that can
be attached to a port can be limited using the Port Security Limit Control
functionality.
 RADIUS-Assigned QoS When RADIUS-Assigned QoS is both globally enabled and enabled (checked)
Enabled for a given port, the switch reacts to QoS Class information carried in the
RADIUS Access-Accept packet transmitted by the RADIUS server when a
supplicant is successfully authenticated. If present and valid, traffic received on

the supplicant's port will be classified to the given QoS Class. If
(re-)authentication fails or the RADIUS Access-Accept packet no longer carries a
QoS Class or it's invalid, or the supplicant is otherwise no longer present on the
port, the port's QoS Class is immediately reverted to the original QoS Class
(which may be changed by the administrator in the meanwhile without affecting
the RADIUS-assigned).
This option is only available for single-client modes, i.e.
 Port-based 802.1X
 Single 802.1X
RADIUS attributes used in identifying a QoS Class:

The User-Priority-Table attribute defined in RFC4675 forms the basis for
identifying the QoS Class in an Access-Accept packet.
Only the first occurrence of the attribute in the packet will be considered, and to
be valid, it must follow this rule:
 All 8 octets in the attribute's value must be identical and consist of ASCII
characters in the range '0' - '7', which translates into the desired QoS Class
in the range [0; 7].
 RADIUS-Assigned When RADIUS-Assigned VLAN is both globally enabled and enabled (checked)
VLAN Enabled for a given port, the switch reacts to VLAN ID information carried in the RADIUS
Access-Accept packet transmitted by the RADIUS server when a supplicant is
229
successfully authenticated. If present and valid, the port's Port VLAN ID will be
changed to this VLAN ID, the port will be set to be a member of that VLAN ID,
and the port will be forced into VLAN unaware mode. Once assigned, all traffic
arriving on the port will be classified and switched on the RADIUS-assigned
VLAN ID.
If (re-)authentication fails or the RADIUS Access-Accept packet no longer carries
a VLAN ID or it's invalid, or the supplicant is otherwise no longer present on the
port, the port's VLAN ID is immediately reverted to the original VLAN ID (which
may be changed by the administrator in the meanwhile without affecting the
RADIUS-assigned).
This option is only available for single-client modes, i.e.
 Single 802.1X
For trouble-shooting VLAN assignments, use the "Monitor→VLANs→VLAN
Membership and VLAN Port" Pages. These Pages show which modules have
(temporarily) overridden the current Port VLAN configuration.
RADIUS attributes used in identifying a VLAN ID:

RFC2868 and RFC3580 form the basis for the attributes used in identifying a
VLAN ID in an Access-Accept packet. The following criteria are used:
 The Tunnel-Medium-Type, Tunnel-Type, and Tunnel-Private-Group-ID
attributes must all be present at least once in the Access-Accept
packet.
 The switch looks for the first set of these attributes that have the same
Tag value and fulfil the following requirements (if Tag == 0 is used, the
Tunnel-Private-Group-ID does not need to include a Tag):
 Value of Tunnel-Medium-Type must be set to "IEEE-802" (ordinal 6).
 Value of Tunnel-Type must be set to "VLAN" (ordinal 13).
 Value of Tunnel-Private-Group-ID must be a string of ASCII chars in
the range '0' - '9', which is interpreted as a decimal string representing
the VLAN ID. Leading '0's are discarded. The final value must be in the
range [1; 4095].
 Guest VLAN Enabled When Guest VLAN is both globally enabled and enabled (checked) for a given
port, the switch considers moving the port into the Guest VLAN according to the
rules outlined below.
This option is only available for EAPOL-based modes, i.e.:
230
 Single 802.1X
 Multi 802.1X
For trouble-shooting VLAN assignments, use the "Monitor→VLANs→VLAN
Membership and VLAN Port" Pages. These Pages show which modules have
(temporarily) overridden the current Port VLAN configuration.
Guest VLAN Operation:

When a Guest VLAN enabled port's link comes up, the switch starts transmitting
EAPOL Request Identity frames. If the number of transmissions of such frames
exceeds Max. Reauth. Count and no EAPOL frames have been received in the
meanwhile, the switch considers entering the Guest VLAN. The interval between
transmission of EAPOL Request Identity frames is configured with EAPOL
Timeout. If Allow Guest VLAN if EAPOL Seen is enabled, the port will now be
placed in the Guest VLAN. If disabled, the switch will first check its history to see
if an EAPOL frame has previously been received on the port (this history is
cleared if the port link goes down or the port's Admin State is changed), and if
not, the port will be placed in the Guest VLAN. Otherwise it will not move to the
Guest VLAN, but continue transmitting EAPOL Request Identity frames at the
rate given by EAPOL Timeout.
Once in the Guest VLAN, the port is considered authenticated, and all attached
clients on the port are allowed access on this VLAN. The switch will not transmit
an EAPOL Success frame when entering the Guest VLAN.
While in the Guest VLAN, the switch monitors the link for EAPOL frames, and if
one such frame is received, the switch immediately takes the port out of the
Guest VLAN and starts authenticating the supplicant according to the port mode.
If an EAPOL frame is received, the port will never be able to go back into the
Guest VLAN if the "Allow Guest VLAN if EAPOL Seen" is disabled.
 Port State The current state of the port. It can undertake one of the following values:
■ Globally Disabled: NAS is globally disabled.
■ Link Down: NAS is globally enabled, but there is no link on the port.
■ Authorized: The port is in Force Authorized or a single-supplicant mode

and the supplicant is authorized.
■ Unauthorized: The port is in Force Unauthorized or a single-supplicant

mode and the supplicant is not successfully authorized by the RADIUS
server.
■ X Auth/Y Unauth: The port is in a multi-supplicant mode. Currently X

clients are authorized and Y are unauthorized.
 Restart Two buttons are available for each row. The buttons are only enabled when
231
authentication is globally enabled and the port's Admin State is in an
EAPOL-based or MAC-based mode.
Clicking these buttons will not cause settings changed on the Page to take effect.
■ Reauthenticate: Schedules a reauthentication to whenever the

quiet-period of the port runs out (EAPOL-based authentication). For
MAC-based authentication, reauthentication will be attempted immediately.
The button only has effect for successfully authenticated clients on the
port and will not cause the clients to get temporarily unauthorized.
■ Reinitialize: Forces a reinitialization of the clients on the port and thereby

a reauthentication immediately. The clients will transfer to the unauthorized
state while the reauthentication is in progress.
Buttons
232
4.11.4 Network Access Overview
This Page provides an overview of the current NAS port states for the selected switch. The Network Access Overview screen in
Figure 4-11-5: Network Access Server Switch Status Page Screenshot
Object Description
 Port The switch port number. Click to navigate to detailed NAS statistics for this port.
 Admin State The port's current administrative state. Refer to NAS Admin State for a
description of possible values.
 Port State The current state of the port. Refer to NAS Port State for a description of the
individual states.
 Last Source The source MAC address carried in the most recently received EAPOL frame for
EAPOL-based authentication, and the most recently received frame from a new
client for MAC-based authentication.
 Last ID The user name (supplicant identity) carried in the most recently received
Response Identity EAPOL frame for EAPOL-based authentication, and the
source MAC address from the most recently received frame from a new client for
MAC-based authentication.
 QoS Class QoS Class assigned to the port by the RADIUS server if enabled.
 Port VLAN ID The VLAN ID that NAS has put the port in. The field is blank, if the Port VLAN ID
is not overridden by NAS.
If the VLAN ID is assigned by the RADIUS server, "(RADIUS-assigned)" is
appended to the VLAN ID. Read more about RADIUS-assigned VLANs here.
If the port is moved to the Guest VLAN, "(Guest)" is appended to the VLAN ID.
Read more about Guest VLANs here.
233
Buttons
4.11.5 Network Access Statistics
This Page provides detailed NAS statistics for a specific switch port running EAPOL-based IEEE 802.1X authentication. For
MAC-based ports, it shows selected backend server (RADIUS Authentication Server) statistics, only. Use the port select box to
select which port details to be displayed. The Network Access Statistics screen in Figure 4-11-6 appears.
Figure 4-11-6: Network Access Statistics Page Screenshot
Port State
Object Description
 Admin State The port's current administrative state. Refer to NAS Admin State for a
description of possible values.
 Port State The current state of the port. Refer to NAS Port State for a description of the
individual states.
 QoS Class The QoS class assigned by the RADIUS server. The field is blank if no QoS class
is assigned.
 Port VLAN ID The VLAN ID that NAS has put the port in. The field is blank, if the Port VLAN ID
is not overridden by NAS.
If the VLAN ID is assigned by the RADIUS server, "(RADIUS-assigned)" is
appended to the VLAN ID. Read more about RADIUS-assigned VLANs here.
If the port is moved to the Guest VLAN, "(Guest)" is appended to the VLAN ID.
Read more about Guest VLANs here.
234
Port Counters
Object Description
 EAPOL Counters These supplicant frame counters are available for the following administrative states:
■ Force Authorized
■ Force Unauthorized
■ Port-based 802.1X
■ Single 802.1X
■ Multi 802.1X
Direction Name IEEE Name Description
Rx Total dot1xAuthEapolFrames The number of valid EAPOL
Rx frames of any type that have
been received by the switch.
Rx Response ID dot1xAuthEapolRespId The number of valid EAPOL
FramesRx Response Identity frames
that have been received by
the switch.
Rx Responses dot1xAuthEapolRespFr The number of valid EAPOL
amesRx response frames (other than
Response Identity frames)
that have been received by
the switch.
Rx Start dot1xAuthEapolStartFra The number of EAPOL Start
mesRx frames that have been
received by the switch.
Rx Logoff dot1xAuthEapolLogoffFr The number of valid EAPOL
amesRx Logoff frames that have
been received by the switch.
Rx Invalid Type dot1xAuthInvalidEapolF The number of EAPOL
ramesRx frames that have been
received by the switch in
which the frame type is not
recognized.
Rx Invalid Length dot1xAuthEapLengthErr The number of EAPOL
orFramesRx frames that have been
received by the switch in
235
which the Packet Body
Length field is invalid.
Tx Total dot1xAuthEapolFrames The number of EAPOL
Tx frames of any type that have
been transmitted by the
switch.
Tx Request ID dot1xAuthEapolReqIdFr The number of EAPOL
amesTx Request Identity frames that
have been transmitted by
the switch.
Tx Requests dot1xAuthEapolReqFra The number of valid EAPOL
mesTx Request frames (other than
Request Identity frames)
that have been transmitted
by the switch.
 Backend Server These backend (RADIUS) frame counters are available for the following administrative
Counters states:
■ Single 802.1X
■ Multi 802.1X
■ MAC-based Auth.
Direction Name IEEE Name Description
Rx Access dot1xAuthBackendAcce 802.1X-based:
Challenges ssChallenges Counts the number of times
that the switch receives the
first request from the backend
server following the first
response from the supplicant.
Indicates that the backend
server has communication
with the switch.
MAC-based:
Counts all Access Challenges
received from the backend
server for this port (left-most
table) or client (right-most
table).
236
Rx Other dot1xAuthBackendOther 802.1X-based:
Requests RequestsToSupplicant Counts the number of times
that the switch sends an EAP
Request packet following the
first to the supplicant.
Indicates that the backend
server chose an EAP-method.
MAC-based:
Not applicable.
Rx Auth. dot1xAuthBackendAuth 802.1X- and MAC-based:
Successes Successes Counts the number of times
that the switch receives a
success indication. Indicates
that the supplicant/client has
successfully authenticated to
the backend server.
Rx Auth. dot1xAuthBackendAuth 802.1X- and MAC-based:
Failures Fails Counts the number of times
that the switch receives a
failure message. This
indicates that the
supplicant/client has not
authenticated to the backend
server.
Tx Responses dot1xAuthBackendResp 802.1X-based:

onses Counts the number of times
that the switch attempts to
send a supplicant's first
response packet to the
backend server. Indicates the
switch attempted
communication with the
backend server. Possible
retransmissions are not
counted.
MAC-based:
Counts all the backend server
packets sent from the switch
towards the backend server
237
for a given port (left-most
table) or client (right-most
table). Possible
retransmissions are not
counted.
 Last Supplicant/Client Information about the last supplicant/client that attempted to authenticate. This
Info information is available for the following administrative states:
■ Single 802.1X
■ Multi 802.1X
■ MAC-based Auth.
Name IEEE Name Description
MAC dot1xAuthLastEapolF The MAC address of the last supplicant/client.
Address rameSource
VLAN ID - The VLAN ID on which the last frame from the
last supplicant/client was received.
Version dot1xAuthLastEapolF 802.1X-based:

rameVersion The protocol version number carried in the most
recently received EAPOL frame.
MAC-based:
Not applicable.
Identity - 802.1X-based:
The user name (supplicant identity) carried in the
most recently received Response Identity
EAPOL frame.
MAC-based:
Not applicable.
Selected Counters
Object Description
 Selected Counters The Selected Counters table is visible when the port is one of the following
administrative states:
■ Multi 802.1X
■ MAC-based Auth.
The table is identical to and is placed next to the Port Counters table, and will be empty if
238
no MAC address is currently selected. To populate the table, select one of the attached
MAC Addresses from the table below.
Attached MAC Address
Object Description
 Identity Shows the identity of the supplicant, as received in the Response Identity EAPOL frame.
Clicking the link causes the supplicant's EAPOL and Backend Server counters to be
shown in the Selected Counters table. If no supplicants are attached, it shows No
supplicants attached.
This column is not available for MAC-based Auth.
 MAC Address For Multi 802.1X, this column holds the MAC address of the attached supplicant.
For MAC-based Auth., this column holds the MAC address of the attached client.
Clicking the link causes the client's Backend Server counters to be shown in the
Selected Counters table. If no clients are attached, it shows No clients attached.
 VLAN ID This column holds the VLAN ID that the corresponding client is currently secured
through the Port Security module.
 State The client can either be authenticated or unauthenticated. In the authenticated state, it is
allowed to forward frames on the port, and in the unauthenticated state, it is blocked. As
long as the backend server hasn't successfully authenticated the client, it is
unauthenticated. If an authentication fails for one or the other reason, the client will
remain in the unauthenticated state for Hold Time seconds.
 Last Authentication Shows the date and time of the last authentication of the client (successful as well as
unsuccessful).
Buttons
: This button is available in the following modes:
• Force Authorized
• Force Unauthorized
• Port-based 802.1X
• Single 802.1X
Click to clear the counters for the selected port.
• Multi 802.1X
• MAC-based Auth.X
239
Click to clear both the port counters and all of the attached client's counters. The "Last Client" will not be
cleared, however.
• Multi 802.1X
• MAC-based Auth.X
Click to clear only the currently selected client's counters.
240
4.11.6 RADIUS
This Page allows you to configure the RADIUS Servers. The RADIUS Configuration screen in Figure 4-11-7 appears.
Figure 4-11-7: RADIUS Server Configuration Page Screenshot
Global Configuration
These setting are common for all of the RADIUS Servers.
Object Description
 Timeout Timeout is the number of seconds, in the range 1 to 1000, to wait for a reply from
a RADIUS server before retransmitting the request.
 Retransmit Retransmit is the number of times, in the range 1 to 1000, a RADIUS request is
retransmitted to a server that is not responding. If the server has not responded
after the last retransmit it is considered to be dead.
 Dead Time The Dead Time, which can be set to a number between 0 and 3600 seconds, is
the period during which the switch will not send new requests to a server that has
failed to respond to a previous request. This will stop the switch from continually
trying to contact a server that it has already determined as dead.
Setting the Dead Time to a value greater than 0 (zero) will enable this feature, but
only if more than one server has been configured.
241
 Key The secret key - up to 63 characters long - shared between the RADIUS server
and the switch.
 NAS-IP-Address The IPv4 address to be used as attribute 4 in RADIUS Access-Request packets.
If this field is left blank, the IP address of the outgoing interface is used.
 NAS-IPv6-Address The IPv6 address to be used as attribute 95 in RADIUS Access-Request
packets. If this field is left blank, the IP address of the outgoing interface is used.
 NAS-Identifier The identifier - up to 253 characters long - to be used as attribute 32 in RADIUS
Access-Request packets. If this field is left blank, the NAS-Identifier is not
included in the packet.
Server Configuration
The table has one row for each RADIUS Server and a number of columns, which are:
Object Description
 Delete To delete a RADIUS server entry, check this box. The entry will be deleted during
the next Save.
 Hostname The IP address or hostname of the RADIUS server.
 Auth Port The UDP port to use on the RADIUS server for authentication.
 Acct Port The UDP port to use on the RADIUS server for accounting.
 Timeout This optional setting overrides the global timeout value. Leaving it blank will use
the global timeout value.
 Retransmit This optional setting overrides the global retransmit value. Leaving it blank will
use the global retransmit value.
 Key This optional setting overrides the global key. Leaving it blank will use the global
key.
Buttons
: Click to add a new RADIUS server. An empty row is added to the table, and the RADIUS
server can be configured as needed. Up to 5 servers are supported.
: Click to undo the addition of the new server.
242
4.11.7 TACACS+
This Page allows you to configure the TACACS+ Servers. The TACACS+ Configuration screen in Figure 4-11-8 appears.
Figure 4-11-8: TACACS+ Server Configuration Page Screenshot
Global Configuration
These setting are common for all of the TACACS+ Servers.
Object Description
 Timeout Timeout is the number of seconds, in the range 1 to 1000, to wait for a reply from
a TACACS+ server before it is considered to be dead.
 Dead Time The Dead Time, which can be set to a number between 0 to 1440 minutes, is the
period during which the switch will not send new requests to a server that has
failed to respond to a previous request. This will stop the switch from continually
trying to contact a server that it has already determined as dead.
Setting the Deadtime to a value greater than 0 (zero) will enable this feature, but
only if more than one server has been configured.
 Key The secret key - up to 63 characters long - shared between the TACACS+ server
and the switch.
Server Configuration
The table has one row for each TACACS+ server and a number of columns, which are:
243
Object Description
 Delete To delete a TACACS+ server entry, check this box. The entry will be deleted during
the next Save.
 Hostname The IP address or hostname of the TACACS+ server.
 Port The TCP port to use on the TACACS+ server for authentication.
 Timeout This optional setting overrides the global timeout value. Leaving it blank will use the
global timeout value.
 Key This optional setting overrides the global key. Leaving it blank will use the global key.
Buttons
: Click to add a new TACACS+ server. An empty row is added to the table, and the
TACACS+ server can be configured as needed. Up to 5 servers are supported.
: Click to undo the addition of the new server.
4.11.8 RADIUS Overview
This Page provides an overview of the status of the RADIUS servers configurable on the Authentication configuration Page. The
RADIUS Authentication/Accounting Server Overview screen in Figure 4-11-9 appears.
Figure 4-11-9: RADIUS Authentication/Accounting Server Overview Page Screenshot
244
RADIUS Authentication Server Status Overview
Object Description
 # The RADIUS server number. Click to navigate to detailed statistics for this server.
 IP Address The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this server.
 Status The current state of the server. This field takes one of the following values:
 Disabled: The server is disabled.
 Not Ready: The server is enabled, but IP communication is not yet up and running.
 Ready: The server is enabled, IP communication is up and running, and the RADIUS
module is ready to accept access attempts.
 Dead (X seconds left): Access attempts were made to this server, but it did not reply
within the configured timeout. The server has temporarily been disabled, but will get
re-enabled when the dead-time expires. The number of seconds left before this occurs
is displayed in parentheses. This state is only reachable when more than one server is
enabled.
RADIUS Accounting Server Status Overview
Object Description
 # The RADIUS server number. Click to navigate to detailed statistics for this server.
 IP Address The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this server.
 Status The current state of the server. This field takes one of the following values:
 Disabled: The server is disabled.
 Not Ready: The server is enabled, but IP communication is not yet up and running.
 Ready: The server is enabled, IP communication is up and running, and the RADIUS
module is ready to accept accounting attempts.
Dead (X seconds left): Accounting attempts were made to this server, but it did not reply
within the configured timeout. The server has temporarily been disabled, but will get
re-enabled when the dead-time expires. The number of seconds left before this occurs is
displayed in parentheses. This state is only reachable when more than one server is
enabled.
Buttons
245
4.11.9 RADIUS Details
This Page provides detailed statistics for a particular RADIUS server. The RADIUS Authentication/Accounting for Server
Overview screen in Figure 4-11-10 appears.
Figure 4-11-10: RADIUS Authentication/Accounting for Server Overview Page Screenshot
RADIUS Authentication Statistics

The statistics map closely to those specified in RFC4668 - RADIUS Authentication Client MIB. Use the server select box to
switch between the backend servers to show details for.
Object Description
 Packet Counters RADIUS authentication server packet counter. There are seven receive and four transmit
counters.
Direction Name RFC4668 Name Description
246
Rx Access radiusAuthClientExtA The number of RADIUS
Accepts ccessAccepts Access-Accept packets (valid
or invalid) received from the
server.
Rx Access Rejects radiusAuthClientExtA The number of RADIUS
ccessRejects Access-Reject packets (valid
or invalid) received from the
server.
Rx Access radiusAuthClientExtA The number of RADIUS
Challenges ccessChallenges Access-Challenge packets
(valid or invalid) received from
the server.
Rx Malformed radiusAuthClientExt The number of malformed
Access MalformedAccessRe RADIUS Access-Response
Responses sponses packets received from the
server. Malformed packets
include packets with an invalid
length. Bad authenticators or
Message Authenticator
attributes or unknown types
are not included as malformed
access responses.
Rx Bad radiusAuthClientExtB The number of RADIUS
Authenticators adAuthenticators Access-Response packets
containing invalid
authenticators or Message
Authenticator attributes
received from the server.
Rx Unknown radiusAuthClientExtU The number of RADIUS
Types nknownTypes packets that were received
from the server on the
authentication port and
dropped for some other
reason.
Rx Packets radiusAuthClientExtP The number of RADIUS
Dropped acketsDropped packets that were received
247
authentication port and
dropped for some other
reason.
Tx Access radiusAuthClientExtA The number of RADIUS
Requests ccessRequests Access-Request packets sent
to the server. This does not
include retransmissions.
Tx Access radiusAuthClientExtA The number of RADIUS
Retransmissio ccessRetransmission Access-Request packets
ns s retransmitted to the RADIUS
authentication server.
Tx Pending radiusAuthClientExtP The number of RADIUS
Requests endingRequests Access-Request packets
destined for the server that
have not yet timed out or
received a response. This
variable is incremented when
an Access-Request is sent and
decremented due to receipt of
an Access-Accept,
Access-Reject,
Access-Challenge, timeout, or
retransmission.
Tx Timeouts radiusAuthClientExtT The number of authentication
imeouts timeouts to the server. After a
timeout, the client may retry to
the same server, send to a
different server, or give up. A
retry to the same server is
counted as a retransmit as well
as a timeout. A send to a
different server is counted as a
Request as well as a timeout.
 Other Info This section contains information about the state of the server and the latest round-trip time.
Name RFC4668 Name Description
IP Address - IP address and UDP port for the authentication server
248
in question.
State - Shows the state of the server. It takes one of the
following values:
 Disabled: The selected server is disabled.

 Not Ready: The server is enabled, but IP
communication is not yet up and running.
 Ready: The server is enabled, IP communication

is up and running, and the RADIUS module is
ready to accept access attempts.
 Dead (X seconds left): Access attempts were

made to this server, but it did not reply within the
configured timeout. The server has temporarily
been disabled, but will get re-enabled when the
dead-time expires. The number of seconds left
before this occurs is displayed in parentheses.
This state is only reachable when more than one
server is enabled.
Round-Trip radiusAuthClient The time interval (measured in milliseconds) between
Time ExtRoundTripTim the most recent Access-Reply/Access-Challenge and
e the Access-Request that matched it from the RADIUS
authentication server. The granularity of this
measurement is 100 ms. A value of 0 ms indicates
that there hasn't been round-trip communication with
the server yet.
RADIUS Accounting Statistics

The statistics map closely to those specified in RFC4670 - RADIUS Accounting Client MIB. Use the server select box to switch
between the backend servers to show details for.
Object Description
 Packet Counters RADIUS accounting server packet counter. There are five receive and four transmit
counters.
Direction Name RFC4670 Name Description
Rx Responses radiusAccClientExt The number of RADIUS
Responses packets (valid or invalid)
received from the server.
249
Rx Malformed radiusAccClientExt The number of malformed
Responses MalformedRespons RADIUS packets received
es from the server. Malformed
packets include packets with
an invalid length. Bad
authenticators or or unknown
types are not included as
malformed access responses.
Rx Bad radiusAcctClientExt The number of RADIUS
Authenticators BadAuthenticators packets containing invalid
authenticators received from
the server.
Rx Unknown Types radiusAccClientExt The number of RADIUS
UnknownTypes packets of unknown types that
were received from the server
on the accounting port.
Rx Packets Dropped radiusAccClientExt The number of RADIUS
PacketsDropped packets that were received
accounting port and dropped
for some other reason.
Tx Requests radiusAccClientExt The number of RADIUS

Requests packets sent to the server.
This does not include
retransmissions.
Tx Retransmissions radiusAccClientExt The number of RADIUS
Retransmissions packets retransmitted to the
RADIUS accounting server.
Tx Pending radiusAccClientExt The number of RADIUS
Requests PendingRequests packets destined for the server
that have not yet timed out or
received a response. This
variable is incremented when
a Request is sent and
decremented due to receipt of
a Response, timeout, or
250
retransmission.
Tx Timeouts radiusAccClientExt The number of accounting
Timeouts timeouts to the server. After a
timeout, the client may retry to
the same server, send to a
different server, or give up. A
retry to the same server is
counted as a retransmit as
well as a timeout. A send to a
different server is counted as a
Request as well as a timeout.
 Other Info This section contains information about the state of the server and the latest round-trip
time.
Name RFC4670 Name Description
IP Address - IP address and UDP port for the accounting
server in question.
State - Shows the state of the server. It takes one of
the following values:
 Disabled: The selected server is disabled.

 Not Ready: The server is enabled, but IP
communication is not yet up and running.
 Ready: The server is enabled, IP

communication is up and running, and the
RADIUS module is ready to accept
accounting attempts.
 Dead (X seconds left): Accounting

attempts were made to this server, but it
did not reply within the configured timeout.
The server has temporarily been disabled,
but will get re-enabled when the dead-time
expires. The number of seconds left
before this occurs is displayed in
parentheses. This state is only reachable
when more than one server is enabled.
Round-Trip radiusAccClientExtRo  The time interval (measured in

Time undTripTime milliseconds) between the most recent
Response and the Request that matched
it from the RADIUS accounting server.
251
The granularity of this measurement is
100 ms. A value of 0 ms indicates that
there hasn't been round-trip
communication with the server yet.
Buttons
: Clears the counters for the selected server. The "Pending Requests" counter will not be cleared by this
operation.
4.11.10 Windows Platform RADIUS Server Configuration
Setup the RADIUS server and assign the client IP address to the Managed switch. In this case, field in the default IP Address
of the Managed Switch with 192.168.0.100. And also make sure the shared secret key is as same as the one you had set at
the Managed Switch’s 802.1x system configuration – 12345678 at this case.
1. Configure the IP Address of remote RADIUS server and secret key.
Figure 4-11-11: RADIUS Server Configuration Screenshot
252
2. Add New RADIUS Cleint on the Windows 2003 server
Figure 4-11-12: Windows Server – Add New RADIUS Client Setting
3. Assign the client IP address to the Managed Switch
Figure 4-11-13: Windows Server RADIUS Server Setting
253
4. The shared secret key should be as same as the key configured on the Managed Switch.
Figure 4-11-14: Windows Server RADIUS Server Setting
5. Configure ports attribute of 802.1X, the same as “802.1X Port Configuration”.
Figure 4-11-15: 802.1x Port Configuration
6. Create user data. The establishment of the user data needs to be created on the Radius Server PC. For example, the
Radius Server founded on Win2003 Server, and then:
254
Figure 4-11-16: Windows 2003 AD Server Setting Path
7. Enter ” Active Directory Users and Computers”, create legal user data; next, right-click a user what you created to
enter properties, and what to be noticed:
255
Figure 4-11-17: Add User Properties Screen
Figure 4-11-18: Add User Properties Screen
Set the Port Authenticate Status to “Force Authorized” if the port is connected to the RADIUS
server or the port is an uplink port that is connected to another switch. Or once the 802.1X starts to
work, the switch might not be able to access the RADIUS server.
256
4.11.11 802.1X Client Configuration
Windows XP is originally 802.1X support. As to other operating systems (windows 98SE, ME, 2000), an 802.1X client utility is
needed. The following procedures show how to configure 802.1X Authentication in Windows XP.
Please note that if you want to change the 802.1x authentication type of a wireless client, i.e. switch to EAP-TLS from EAP-MD5,
you must remove the current existing wireless network from your preferred connection first, and add it in again.
 Configure Sample: EAP-MD5 Authentication
1. Go to Start > Control Panel, double-click on “Network Connections”.
2. Right-click on the Local Network Connection.
3. Click “Properties” to open up the Properties setting window.
Figure 4-11-19
4. Select “Authentication” tab.
5. Select “Enable network access control using IEEE 802.1X” to enable 802.1x authentication.
6. Select “MD-5 Challenge” from the drop-down list box for EAP type.
257
Figure 4-11-20
7. Click “OK”.
8. When client has associated with the Managed Switch, a user authentication notice appears in system tray. Click on the
notice to continue.
Figure 4-11-21: Windows Client Popup Login Request Message
258
9. Enter the user name, password and the logon domain that your account belongs.
10. Click “OK” to complete the validation process.
Figure 4-11-22
259
4.12 Security
This section is to control the access of the Managed Switch, includes the user access and management control.
The Security Page contains links to the following main topics:
 Port Limit Control
 Access Management
 HTTPs / SSH
 DHCP Snooping
 IP Source Guard
 ARP Inspection
4.12.1 Port Limit Control
This Page allows you to configure the Port Security Limit Control system and port settings. Limit Control allows for limiting the
number of users on a given port. A user is identified by a MAC address and VLAN ID. If Limit Control is enabled on a port, the
limit specifies the maximum number of users on the port. If this number is exceeded, an action is taken. The action can be one
of the four different actions as described below.
The Limit Control module utilizes a lower-layer module, Port Security module, which manages MAC addresses learnt on the port.
The Limit Control configuration consists of two sections, a system- and a port-wide. The Port Limit Control Configuration screen
in Figure 4-12-1 appears.
Figure 4-12-1: Port Limit Control Configuration Overview Page Screenshot
260
System Configuration
Object Description
 Mode Indicates if Limit Control is globally enabled or disabled on the switch. If globally
disabled, other modules may still use the underlying functionality, but limit checks
and corresponding actions are disabled.
 Aging Enabled If checked, secured MAC addresses are subject to aging as discussed under
Aging Period.
 Aging Period If Aging Enabled is checked, then the aging period is controlled with this input. If
other modules are using the underlying port security for securing MAC
addresses, they may have other requirements to the aging period. The
underlying port security will use the shorter requested aging period of all modules
that use the functionality.
The Aging Period can be set to a number between 10 and 10,000,000 seconds.
To understand why aging may be desired, consider the following scenario:
Suppose an end-host is connected to a 3rd party switch or hub, which in turn is
connected to a port on this switch on which Limit Control is enabled. The
end-host will be allowed to forward if the limit is not exceeded. Now suppose that
the end-host logs off or powers down. If it wasn't for aging, the end-host would
still take up resources on this switch and will be allowed to forward. To overcome
this situation, enable aging. With aging enabled, a timer is started once the
end-host gets secured. When the timer expires, the switch starts looking for
frames from the end-host, and if such frames are not seen within the next Aging
Period, the end-host is assumed to be disconnected, and the corresponding
resources are freed on the switch.
Port Configuration
The table has one row for each port and a number of columns, which are:
Object Description
 Mode Controls whether Limit Control is enabled on this port. Both this and the Global
Mode must be set to Enabled for Limit Control to be in effect. Notice that other
modules may still use the underlying port security features without enabling Limit
Control on a given port.
261
 Limit The maximum number of MAC addresses that can be secured on this port. This
number cannot exceed 1024. If the limit is exceeded, the corresponding action is
taken.
The switch is "born" with a total number of MAC addresses from which all ports
draw whenever a new MAC address is seen on a Port Security-enabled port.
Since all ports draw from the same pool, it may happen that a configured
maximum cannot be granted, if the remaining ports have already used all
available MAC addresses.
 Action If Limit is reached, the switch can take one of the following actions:
 None: Do not allow more than Limit MAC addresses on the port, but take no
further action.
 Trap: If Limit + 1 MAC addresses is seen on the port, send an SNMP trap. If
Aging is disabled, only one SNMP trap will be sent, but with Aging enabled,
new SNMP traps will be sent everytime the limit gets exceeded.
 Shutdown: If Limit + 1 MAC addresses is seen on the port, shut down the
port. This implies that all secured MAC addresses will be removed from the
port, and no new will be learned. Even if the link is physically disconnected
and reconnected on the port (by disconnecting the cable), the port will
remain shut down. There are three ways to re-open the port:
1) Boot the switch,
2) Disable and re-enable Limit Control on the port or the switch,
3) Click the Reopen button.
 Trap & Shutdown: If Limit + 1 MAC addresses is seen on the port, both the
"Trap" and the "Shutdown" actions described above will be taken.
 State This column shows the current state of the port as seen from the Limit Control's
point of view. The state takes one of four values:
 Disabled: Limit Control is either globally disabled or disabled on the port.
 Ready: The limit is not yet reached. This can be shown for all actions.
 Limit Reached: Indicates that the limit is reached on this port. This state can
only be shown if Action is set to None or Trap.
 Shutdown: Indicates that the port is shut down by the Limit Control module.
This state can only be shown if Action is set to Shutdown or Trap &
Shutdown.
262
 Re-open Button If a port is shutdown by this module, you may reopen it by clicking this button,
which will only be enabled if this is the case. For other methods, refer to
Shutdown in the Action section.
Note, that clicking the reopen button causes the Page to be refreshed, so
non-committed changes will be lost.
Buttons
: Click to refresh the Page. Note that non-committed changes will be lost.
263
4.12.2 Access Management
Configure access management table on this Page. The maximum entry number is 16. If the application's type match any one of
the access management entries, it will allow access to the switch. The Access Management Configuration screen in Figure
4-12-2 appears.
Figure 4-12-2: Access Management Configuration Overview Page Screenshot
Object Description
 Mode Indicates the access management mode operation. Possible modes are:
Enabled: Enable access management mode operation.
Disabled: Disable access management mode operation.
 Delete Check to delete the entry. It will be deleted during the next apply .
 VLAN ID Indicates the VLAN ID for the access management entry.
 Start IP address Indicates the start IP address for the access management entry.
 End IP address Indicates the end IP address for the access management entry.
 HTTP/HTTPS Indicates the host can access the switch from HTTP/HTTPS interface that the
host IP address matched the entry.
 SNMP Indicates the host can access the switch from SNMP interface that the host IP
address matched the entry.
 TELNET/SSH Indicates the host can access the switch from TELNET/SSH interface that the
host IP address matched the entry.
Buttons
: Click to add a new access management entry.
264
4.12.3 Access Management Statistics
This Page provides statistics for access management. The Access Management Statistics screen in Figure 4-12-3 appears.
Figure 4-12-3: Access Management Statistics Overview Page Screenshot
Object Description
 Interface The interface that allowed remote host can access the switch.
 Receive Packets The received packets number from the interface under access management
mode is enabled.
 Allow Packets The allowed packets number from the interface under access management
mode is enabled.
 Discard Packets The discarded packets number from the interface under access management
mode is enabled.
Buttons
: Clears all statistics.
265
4.12.4 HTTPs
Configure HTTPS on this Page. The HTTPS Configuration screen in Figure 4-12-4 appears.
Figure 4-12-4: HTTPS Configuration Screen Page Screenshot
Object Description
 Mode Indicates the HTTPS mode operation. When the current connection is HTTPS, to
apply HTTPS disabled mode operation will automatically redirect web browser to
an HTTP connection. Possible modes are:
 Enabled: Enable HTTPS mode operation.
 Disabled: Disable HTTPS mode operation.
 Automatic Redirect Indicates the HTTPS redirect mode operation. It only significant if HTTPS mode
"Enabled" is selected. Automatically redirects web browser to an HTTPS
connection when both HTTPS mode and Automatic Redirect are enabled or
redirects web browser to an HTTP connection when both are disabled. Possible
modes are:
 Enabled: Enable HTTPS redirect mode operation.
 Disabled: Disable HTTPS redirect mode operation.
Buttons
266
4.12.5 SSH
Configure SSH on this Page. This Page shows the Port Security status. Port Security is a module with no direct configuration.
Configuration comes indirectly from other modules - the user modules. When a user module has enabled port security on a port,
the port is set-up for software-based learning. In this mode, frames from unknown MAC addresses are passed on to the port
security module, which in turn asks all user modules whether to allow this new MAC address to forward or block it. For a MAC
address to be set in the forwarding state, all enabled user modules must unanimously agree on allowing the MAC address to
forward. If only one chooses to block it, it will be blocked until that user module decides otherwise.
The status Page is divided into two sections - one with a legend of user modules and one with the actual port status. The SSH
Figure 4-12-5: SSH Configuration Screen Page Screenshot
Object Description
 Mode Indicates the SSH mode operation. Possible modes are:
 Enabled: Enable SSH mode operation.
 Disabled: Disable SSH mode operation.
Buttons
4.12.6 Port Security Status
This Page shows the Port Security status. Port Security is a module with no direct configuration. Configuration comes indirectly
from other modules - the user modules. When a user module has enabled port security on a port, the port is set-up for
software-based learning. In this mode, frames from unknown MAC addresses are passed on to the port security module, which
in turn asks all user modules whether to allow this new MAC address to forward or block it. For a MAC address to be set in the
forwarding state, all enabled user modules must unanimously agree on allowing the MAC address to forward. If only one
chooses to block it, it will be blocked until that user module decides otherwise.
The status Page is divided into two sections - one with a legend of user modules and one with the actual port status. The Port
267
Security Status screen in Figure 4-12-6 appears.
Figure 4-12-6: Port Security Status Screen Page Screenshot
User Module Legend

The legend shows all user modules that may request Port Security services.
Object Description
 User Module Name The full name of a module that may request Port Security services.
 Abbr A one-letter abbreviation of the user module. This is used in the Users column in
the port status table.
Port Status
The table has one row for each port on the selected switch in the switch and a number of columns, which are:
Object Description
 Port The port number for which the status applies. Click the port number to see the
status for this particular port.
 Users Each of the user modules has a column that shows whether that module has
enabled Port Security or not. A '-' means that the corresponding user module is
268
not enabled, whereas a letter indicates that the user module abbreviated by that
letter has enabled port security.
 State Shows the current state of the port. It can take one of four values:
 Disabled: No user modules are currently using the Port Security service.
 Ready: The Port Security service is in use by at least one user module, and
is awaiting frames from unknown MAC addresses to arrive.
 Limit Reached: The Port Security service is enabled by at least the Limit
Control user module, and that module has indicated that the limit is reached
and no more MAC addresses should be taken in.
 Shutdown: The Port Security service is enabled by at least the Limit Control
user module, and that module has indicated that the limit is exceeded. No
MAC addresses can be learned on the port until it is administratively
re-opened on the Limit Control configuration Web-Page.
 MAC Count The two columns indicate the number of currently learned MAC addresses
(Current, Limit) (forwarding as well as blocked) and the maximum number of MAC addresses
that can be learned on the port, respectively.
If no user modules are enabled on the port, the Current column will show a dash
(-).
If the Limit Control user module is not enabled on the port, the Limit column will
show a dash (-).
Buttons
269
4.12.7 Port Security Detail
This Page shows the MAC addresses secured by the Port Security module. Port Security is a module with no direct
configuration. Configuration comes indirectly from other modules - the user modules. When a user module has enabled port
security on a port, the port is set-up for software-based learning. In this mode, frames from unknown MAC addresses are
passed on to the port security module, which in turn asks all user modules whether to allow this new MAC address to forward or
block it. For a MAC address to be set in the forwarding state, all enabled user modules must unanimously agree on allowing the
MAC address to forward. If only one chooses to block it, it will be blocked until that user module decides otherwise. The Port
Security Detail screen in Figure 4-12-7 appears.
Figure 4-12-7: Port Security Detail Screen Page Screenshot
Object Description
 MAC Address & VLAN The MAC address and VLAN ID that is seen on this port. If no MAC addresses
ID are learned, a single row stating "No MAC addresses attached" is displayed.
 State Indicates whether the corresponding MAC address is blocked or forwarding. In
the blocked state, it will not be allowed to transmit or receive traffic.
 Time of Addition Shows the date and time when this MAC address was first seen on the port.
 Age/Hold  If at least one user module has decided to block this MAC address, it will
stay in the blocked state until the hold time (measured in seconds) expires.
 If all user modules have decided to allow this MAC address to forward, and
aging is enabled, the Port Security module will periodically check that this
MAC address still forwards traffic.
 If the age period (measured in seconds) expires and no frames have been
seen, the MAC address will be removed from the MAC table. Otherwise a
new age period will begin.
 If aging is disabled or a user module has decided to hold the MAC address
indefinitely, a dash (-) will be shown.
270
4.12.8 DHCP Snooping
DHCP Snooping is used to block intruder on the untrusted ports of DUT when it tries to intervene by injecting a bogus DHCP
reply packet to a legitimate conversation between the DHCP client and server.
Configure DHCP Snooping on this Page. The DHCP Snooping Configuration screen in Figure 4-12-8 appears.
271
Figure 4-12-8: DHCP Snooping Configuration Screen Page Screenshot
Object Description
 Snooping Mode Indicates the DHCP snooping mode operation. Possible modes are:
 Enabled: Enable DHCP snooping mode operation. When enable DHCP

snooping mode operation, the request DHCP messages will be forwarded to
trusted ports and only allowed reply packets from trusted ports.
 Disabled: Disable DHCP snooping mode operation.

 Port Mode Indicates the DHCP snooping port mode. Possible port modes are:
Configuration  Trusted: Configures the port as trusted sources of the DHCP message.
 Untrusted: Configures the port as untrusted sources of the DHCP message.
Buttons
272
4.12.9 Snooping Table
This page display the dynamic IP assigned information after DHCP Snooping mode is disabled. All DHCP clients
obtained the dynamic IP address from the DHCP server will be listed in this table except for local VLAN interface IP
addresses. Entries in the Dynamic DHCP snooping Table are shown on this page. The Dynamic DHCP Snooping Table
Figure 4-12-9: Dynamic DHCP Snooping Table Screen Page Screenshot
Buttons
: It will use the last entry of the currently displayed table as a basis for the next lookup. When the end is
reached the text "No more entries" is shown in the displayed table
: To start over
4.12.10 IP Source Guard Configuration
IP Source Guard is a secure feature used to restrict IP traffic on DHCP snooping untrusted ports by filtering traffic based on
the DHCP Snooping Table or manually configured IP Source Bindings. It helps prevent IP spoofing attacks when a host tries to
spoof and use the IP address of another host. This Page provides IP Source Guard related configuration. The IP Source Guard
273
Figure 4-12-10: IP Source Guard Configuration Screen Page Screenshot
Object Description
 Mode of IP Source Enable the Global IP Source Guard or disable the Global IP Source Guard. All
Guard Configuration configured ACEs will be lost when the mode is enabled.
 Port Mode Specify IP Source Guard is enabled on which ports. Only when both Global Mode
Configuration and Port Mode on a given port are enabled, IP Source Guard is enabled on this
given port.
 Max Dynamic Clients Specify the maximum number of dynamic clients can be learned on given ports.
This value can be 0, 1, 2 and unlimited. If the port mode is enabled and the value
of max dynamic client is equal 0, it means only allow the IP packets forwarding
that are matched in static entries on the specific port.
Buttons
: Click to translate all dynamic entries to static entries.
274
4.12.11 IP Source Guard Static Table
This Page provides Static IP Source Guard Table. The Static IP Source Guard Table screen in Figure 4-12-11 appears.
Figure 4-12-11: Static IP Source Guard Table Screen Page Screenshot
Object Description
 VLAN ID The VLAN ID for the settings.
 IP Address Allowed Source IP address.
 MAC Address Allowed Source MAC address.
Buttons
: Click to add a new entry to the Static IP Source Guard table.
275
4.12.12 ARP Inspection
ARP Inspection is a secure feature. Several types of attacks can be launched against a host or devices connected to Layer 2
networks by "poisoning" the ARP caches. This feature is used to block such attacks. Only valid ARP requests and responses
can go through DUT. This Page provides ARP Inspection related configuration. The ARP Inspection Configuration screen in
Figure 4-12-12: ARP Inspection Configuration Screen Page Screenshot
Object Description
 Mode of ARP Inspection Enable the Global ARP Inspection or disable the Global ARP Inspection.
Configuration
 Port Mode Configuration Specify ARP Inspection is enabled on which ports. Only when both Global
Mode and Port Mode on a given port are enabled, ARP Inspection is enabled
on this given port. Possible modes are:
 Enabled: Enable ARP Inspection operation.

 Disabled: Disable ARP Inspection operation.
If you want to inspect the VLAN configuration, you have to enable the setting
276
of "Check VLAN". The default setting of "Check VLAN" is disabled. When the
setting of "Check VLAN" is disabled, the log type of ARP Inspection will refer
to the port setting. And the setting of "Check VLAN" is enabled, the log type of
ARP Inspection will refer to the VLAN setting. Possible setting of "Check
VLAN" are:
 Enabled: Enable check VLAN operation.

 Disabled: Disable check VLAN operation.
Only the Global Mode and Port Mode on a given port are enabled, and the
setting of "Check VLAN" is disabled, the log type of ARP Inspection will refer
to the port setting. There are four log types and possible types are:
 None: Log nothing.

 Deny: Log denied entries.
 Permit: Log permitted entries.
 ALL: Log all entries.
Buttons
: Click to translate all dynamic entries to static entries.
4.12.13 ARP Inspection Static Table
This Page provides Static ARP Inspection Table. The Static ARP Inspection Table screen in Figure 4-12-13 appears.
Figure 4-12-13: Static ARP Inspection Table Screen Page Screenshot
Object Description
277
 VLAN ID The VLAN ID for the settings.
 MAC Address Allowed Source MAC address in ARP request packets.
 IP Address Allowed Source IP address in ARP request packets.
Buttons
: Click to add a new entry to the Static ARP Inspection table.
4.12.14 Dynamic ARP Inspection Table
Entries in the Dynamic ARP Inspection Table are shown on this Page. The Dynamic ARP Inspection Table contains up to 1024
entries, and is sorted first by port, then by VLAN ID, then by MAC address, and then by IP address. The Dynamic ARP
Inspection Table screen in Figure 4-12-14 appears.
Figure 4-12-14: Dynamic ARP Inspection Table Screenshot
Navigating the ARP Inspection Table

Each Page shows up to 99 entries from the Dynamic ARP Inspection table, default being 20, selected through the "entries per
Page" input field. When first visited, the web Page will show the first 20 entries from the beginning of the Dynamic ARP
Inspection Table.
The "Start from port address", "VLAN", "MAC address" and "IP address" input fields allow the user to select the starting point
in the Dynamic ARP Inspection Table. Clicking the “Refresh” button will update the displayed table starting from that or the
closest next Dynamic ARP Inspection Table match. In addition, the two input fields will - upon a “Refresh” button click - assume
the value of the first displayed entry, allowing for continuous refresh with the same start address.
The “>>” will use the last entry of the currently displayed as a basis for the next lookup. When the end is reached the text "No
278
more entries" is shown in the displayed table. Use the “|<<” button to start over. The Page includes the following fields:
Object Description
 Port The port number for which the status applies. Click the port number to see the
status for this particular port.
 MAC Address The MAC address of the entry.
 IP Address The IP address of the entry.
Buttons
: Refreshes the displayed table starting from the "Start from MAC address" and "VLAN" input fields.
: Flushes all dynamic entries.
: Updates the table starting from the first entry in the MAC Table, i.e. the entry with the lowest VLAN ID and MAC
address.
279
4.13 Address Table

Switching of frames is based upon the DMAC address contained in the frame. The Managed Switch builds up a table that maps
MAC addresses to switch ports for knowing which ports the frames should go to (based upon the DMAC address in the frame ).
This table contains both static and dynamic entries. The static entries are configured by the network administrator if the
administrator wants to do a fixed mapping between the DMAC address and switch ports.
The frames also contain a MAC address (SMAC address ), which shows the MAC address of the equipment sending the frame.
The SMAC address is used by the switch to automatically update the MAC table with these dynamic MAC addresses. Dynamic
entries are removed from the MAC table if no frame with the corresponding SMAC address have been seen after a configurable
age time.
4.13.1 MAC Table Configuration
The MAC Address Table is configured on this Page. Set timeouts for entries in the dynamic MAC Table and configure the static
MAC table here. The MAC Address Table Configuration screen in Figure 4-13-1 appears.
Figure 4-13-1: MAC Address Table Configuration Page Screenshot
Aging Configuration
By default, dynamic entries are removed from the MAC table after 300 seconds. This removal is also called aging.
Object Description
 Disable Automatic Enables/disables the the automatic aging of dynamic entries
Aging
 Aging Time The time after which a learned entry is discarded. By default, dynamic entries are
removed from the MAC after 300 seconds. This removal is also called aging.
280
(Range: 10-10000000 seconds; Default: 300 seconds)
MAC Table Learning

If the learning mode for a given port is greyed out, another module is in control of the mode, so that it cannot be changed by the
user. An example of such a module is the MAC-Based Authentication under 802.1X.
Object Description
 Auto Learning is done automatically as soon as a frame with unknown SMAC is received.
 Disable No learning is done.
 Secure Only static MAC entries are learned, all other frames are dropped.
Note: Make sure that the link used for managing the switch is added to the Static
Mac Table before changing to secure learning mode, otherwise the management
link is lost and can only be restored by using another non-secure port or by
connecting to the switch via the serial interface.
Static MAC Table Configuration

The static entries in the MAC table are shown in this table. The static MAC table can contain 64 entries. The MAC table is sorted
first by VLAN ID and then by MAC address.
Object Description
 Port Members Checkmarks indicate which ports are members of the entry. Check or uncheck as
needed to modify the entry.
 Adding a New Static

Click to add a new entry to the static MAC table.
Entry
Specify the VLAN ID, MAC address, and port members for the new entry. Click
"Save".
Buttons
281
4.13.2 MAC Address Table Status
Dynamic MAC Table

Entries in the MAC Table are shown on this Page. The MAC Table contains up to 8192 entries, and is sorted first by VLAN ID,
then by MAC address. The MAC Address Table screen in Figure 4-13-2 appears.
Figure 4-13-2: MAC Address Table Status Page Screenshot
Navigating the MAC Table

Each Page shows up to 999 entries from the MAC table, default being 20, selected through the "entries per Page" input
field. When first visited, the web Page will show the first 20 entries from the beginning of the MAC Table. The first displayed
will be the one with the lowest VLAN ID and the lowest MAC address found in the MAC Table.
The "Start from MAC address" and "VLAN" input fields allow the user to select the starting point in the MAC Table.
Clicking the “Refresh” button will update the displayed table starting from that or the closest next MAC Table match.
In addition, the two input fields will - upon a “Refresh” button click - assume the value of the first displayed entry, allowing
for continuous refresh with the same start address.
The “>>” will use the last entry of the currently displayed VLAN/MAC address pairs as a basis for the next lookup. When the
end is reached the text "no more entries" is shown in the displayed table. Use the “|<<” button to start over.
Object Description
 Type Indicates whether the entry is a static or dynamic entry.
 VLAN The VLAN ID of the entry.
 Port Members The ports that are members of the entry.
282
Buttons
: Refreshes the displayed table starting from the "Start from MAC address" and "VLAN" input fields.
: Flushes all dynamic entries.
: Updates the table starting from the first entry in the MAC Table, i.e. the entry with the lowest VLAN ID and MAC
address.
283
4.14 LLDP
4.14.1 Link Layer Discovery Protocol

Link Layer Discovery Protocol (LLDP) is used to discover basic information about neighboring devices on the local broadcast
domain. LLDP is a Layer 2 protocol that uses periodic broadcasts to advertise information about the sending device. Advertised
information is represented in Type Length Value (TLV) format according to the IEEE 802.1ab standard, and can include details
such as device identification, capabilities and configuration settings. LLDP also defines how to store and maintain information
gathered about the neighboring network nodes it discovers.
Link Layer Discovery Protocol - Media Endpoint Discovery (LLDP-MED) is an extension of LLDP intended for managing
endpoint devices such as Voice over IP phones and network switches. The LLDP-MED TLVs advertise information such as
network policy, power, inventory, and device location details. LLDP and LLDP-MED information can be used by SNMP
applications to simplify troubleshooting, enhance network management, and maintain an accurate network topology.
4.14.2 LLDP Configuration
This Page allows the user to inspect and configure the current LLDP port settings. The LLDP Configuration screen in Figure
4-14-1 appears.
Figure 4-14-1: LLDP Configuration Page Screenshot
284
LLDP Parameters
Object Description
 Tx Interval The switch is periodically transmitting LLDP frames to its neighbors for having the
network discovery information up-to-date. The interval between each LLDP
frame is determined by the Tx Interval value. Valid values are restricted to 5 -

32768 seconds.
Default: 30 seconds
This attribute must comply with the following rule:
(Transmission Interval * Hold Time Multiplier) ≤65536, and Transmission Interval
>= (4 * Delay Interval)
 Tx Hold Each LLDP frame contains information about how long the information in the
LLDP frame shall be considered valid. The LLDP information valid period is set to
Tx Hold multiplied by Tx Interval seconds. Valid values are restricted to 2 - 10

times.
TTL in seconds is based on the following rule:
(Transmission Interval * Holdtime Multiplier) ≤ 65536.
Therefore, the default TTL is 4*30 = 120 seconds.
 Tx Delay If some configuration is changed (e.g. the IP address) a new LLDP frame is
transmitted, but the time between the LLDP frames will always be at least the
value of Tx Delay seconds. Tx Delay cannot be larger than 1/4 of the Tx Interval
value. Valid values are restricted to 1 - 8192 seconds.
This attribute must comply with the rule:
(4 * Delay Interval) ≤Transmission Interval
 Tx Reinit When a port is disabled, LLDP is disabled or the switch is rebooted a LLDP
shutdown frame is transmitted to the neighboring units, signaling that the LLDP
information isn't valid anymore. Tx Reinit controls the amount of seconds

between the shutdown frame and a new LLDP initialization. Valid values are
restricted to 1 - 10 seconds.
LLDP Port Configuration

The LLDP port settings relate to the switch, as reflected by the Page header.
Object Description
 Port The switch port number of the logical LLDP port.
 Mode Select LLDP mode.
 Rx only The switch will not send out LLDP information, but LLDP information
from neighbor units is analyzed.
285
 Tx only The switch will drop LLDP information received from neighbors, but
will send out LLDP information.
 Disabled The switch will not send out LLDP information, and will drop LLDP
information received from neighbors.
 Enabled The switch will send out LLDP information, and will analyze LLDP
information received from neighbors.
 CDP Aware Select CDP awareness.
The CDP operation is restricted to decoding incoming CDP frames (The switch
doesn't transmit CDP frames). CDP frames are only decoded if LLDP on the
port is enabled.
Only CDP TLVs that can be mapped to a corresponding field in the LLDP
neighbours' table are decoded. All other TLVs are discarded (Unrecognized CDP
TLVs and discarded CDP frames are not shown in the LLDP statistics.). CDP
TLVs are mapped onto LLDP neighbours' table as shown below.
CDP TLV "Device ID" is mapped to the LLDP "Chassis ID" field.
CDP TLV "Address" is mapped to the LLDP "Management Address" field. The
CDP address TLV can contain multiple addresses, but only the first address is
shown in the LLDP neighbours table.
CDP TLV "Port ID" is mapped to the LLDP "Port ID" field.
CDP TLV "Version and Platform" is mapped to the LLDP "System Description"
field.
Both the CDP and LLDP support "system capabilities", but the CDP capabilities
cover capabilities that are not part of the LLDP. These capabilities are shown as
"others" in the LLDP neighbours' table.
If all ports have CDP awareness disabled the switch forwards CDP frames
received from neighbour devices. If at least one port has CDP awareness
enabled all CDP frames are terminated by the switch.
Note: When CDP awareness on a port is disabled the CDP information isn't
removed immediately, but gets removed when the hold time is exceeded.
 Port Description Optional TLV: When checked the "port description" is included in LLDP
information transmitted.
 System Name Optional TLV: When checked the "system name" is included in LLDP information
transmitted.
 System Description Optional TLV: When checked the "system description" is included in LLDP
 System Capabilites Optional TLV: When checked the "system capability" is included in LLDP
 Management Address Optional TLV: When checked the "management address" is included in LLDP
286
Buttons
4.14.3 LLDP MED Configuration
This Page allows you to configure the LLDP-MED. The LLDPMED Configuration screen in Figure 4-14-2 appears.
Figure 4-14-2: LLDPMED Configuration Page Screenshot
Fast start repeat count
Object Description
 Fast start repeat count Rapid startup and Emergency Call Service Location Identification Discovery of
endpoints is a critically important aspect of VoIP systems in general. In addition, it
is best to advertise only those pieces of information which are specifically
relevant to particular endpoint types (for example only advertise the voice
network policy to permitted voice-capable devices), both in order to conserve the
limited LLDPU space and to reduce security and system integrity issues that can
287
come with inappropriate knowledge of the network policy.
With this in mind LLDP-MED defines an LLDP-MED Fast Start interaction
between the protocol and the application layers on top of the protocol, in order to
achieve these related properties. Initially, a Network Connectivity Device will only
transmit LLDP TLVs in an LLDPDU. Only after an LLDP-MED Endpoint Device is
detected, will an LLDP-MED capable Network Connectivity Device start to
advertise LLDP-MED TLVs in outgoing LLDPDUs on the associated port. The
LLDP-MED application will temporarily speed up the transmission of the
LLDPDU to start within a second, when a new LLDP-MED neighbour has been
detected in order share LLDP-MED information as fast as possible to new
neighbours.
Because there is a risk of an LLDP frame being lost during transmission between
neighbours, it is recommended to repeat the fast start transmission multiple times
to increase the possibility of the neighbours receiving the LLDP frame. With Fast
start repeat count it is possible to specify the number of times the fast start
transmission would be repeated. The recommended value is 4 times, given that 4
LLDP frames with a 1 second interval will be transmitted, when an LLDP frame
with new information is received.
It should be noted that LLDP-MED and the LLDP-MED Fast Start mechanism is
only intended to run on links between LLDP-MED Network Connectivity Devices
and Endpoint Devices, and as such does not apply to links between LAN
infrastructure elements, including Network Connectivity Devices, or other types
of links.
Coordinates Location
Object Description
 Latitude Latitude SHOULD be normalized to within 0-90 degrees with a maximum of 4

digits.
It is possible to specify the direction to either North of the equator or South of the
equator.
 Longitude Longitude SHOULD be normalized to within 0-180 degrees with a maximum of 4

digits.
It is possible to specify the direction to either East of the prime meridian or West
of the prime meridian.
 Altitude Altitude SHOULD be normalized to within -32767 to 32767 with a maximum of 4

digits.
It is possible to select between two altitude types (floors or meters).
Meters: Representing meters of Altitude defined by the vertical datum specified.
288
Floors: Representing altitude in a form more relevant in buildings which have

different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a
building, and represents ground level at the given latitude and longitude. Inside a
building, 0.0 represents the floor level associated with ground level at the main
entrance.
 Map Datum The Map Datum used for the coordinates given in this Option
 WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code

4327, Prime Meridian Name: Greenwich.
 NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime

Meridian Name: Greenwich; The associated vertical datum is the North
American Vertical Datum of 1988 (NAVD88). This datum pair is to be used
when referencing locations on land, not near tidal water (which would use
Datum = NAD83/MLLW).
 NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime

Meridian Name: Greenwich; The associated vertical datum is Mean Lower
Low Water (MLLW). This datum pair is to be used when referencing locations
on water/sea/ocean.
Civic Address Location

IETF Geopriv Civic Address based Location Configuration Information (Civic Address LCI).
Object Description
 Country code The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE
or US.
 State National subdivisions (state, canton, region, province, prefecture).
 County County, parish, gun (Japan), district.
 City City, township, shi (Japan) - Example: Copenhagen
 City district City division, borough, city district, ward, chou (Japan)
 Block (Neighborhood) Neighborhood, block
 Street Street - Example: Poppelvej
 Leading street Leading street direction - Example: N
direction
 Trailing street suffix Trailing street suffix - Example: SW
 Street suffix Street suffix - Example: Ave, Platz
 House no. House number - Example: 21
 House no. suffix House number suffix - Example: A, 1/2
 Landmark Landmark or vanity address - Example: Columbia University
 Additional location Additional location info - Example: South Wing
info
 Name Name (residence and office occupant) - Example: Flemming Jahn
289
 Zip code Postal/zip code - Example: 2791
 Building Building (structure) - Example: Low Library
 Apartment Unit (Apartment, suite) - Example: Apt 42
 Floor Floor - Example: 4
 Room no. Room number - Example: 450F
 Place type Place type - Example: Office
 Postal community Postal community name - Example: Leonia
name
 P.O. Box Post office box (P.O. BOX) - Example: 12345
 Additional code Additional code - Example: 1320300003
Emergency Call Service

Emergency Call Service (e.g. E911 and others), such as defined by TIA or NENA.
Object Description
 Emergency Call Emergency Call Service ELIN identifier data format is defined to carry the ELIN
Service identifier as used during emergency call setup to a traditional CAMA or ISDN
trunk-based PSAP. This format consists of a numerical digit string, corresponding
to the ELIN to be used for emergency calling.
Policies
Network Policy Discovery enables the efficient discovery and diagnosis of mismatch issues with the VLAN configuration, along
with the associated Layer 2 and Layer 3 attributes, which apply for a set of specific protocol applications on that port. Improper
network policy configurations are a very significant issue in VoIP environments that frequently result in voice quality degradation
or loss of service.
Policies are only intended for use with applications that have specific 'real-time’ network policy requirements, such as interactive
voice and/or video services.
The network policy attributes advertised are:
1. Layer 2 VLAN ID (IEEE 802.1Q-2003)
2. Layer 2 priority value (IEEE 802.1D-2004)
3. Layer 3 Diffserv code point (DSCP) value (IETF RFC 2474)
This network policy is potentially advertised and associated with multiple sets of application types supported on a given port.
The application types specifically addressed are:
1. Voice
2. Guest Voice
3. Softphone Voice
290
4. Video Conferencing
5. Streaming Video
6. Control / Signaling (conditionally support a separate network policy for the media types above)
A large network may support multiple VoIP policies across the entire organization, and different policies per application type.
LLDP-MED allows multiple policies to be advertised per port, each corresponding to a different application type. Different ports
on the same Network Connectivity Device may advertise different sets of policies, based on the authenticated user identity or
port configuration.
It should be noted that LLDP-MED is not intended to run on links other than between Network Connectivity Devices and
Endpoints, and therefore does not need to advertise the multitude of network policies that frequently run on an aggregated link
interior to the LAN.
Object Description
 Delete Check to delete the policy. It will be deleted during the next save.
 Policy ID ID for the policy. This is auto generated and shall be used when selecting the
polices that shall be mapped to the specific ports.
 Application Type Intended use of the application types:
 Voice - for use by dedicated IP Telephony handsets and other similar

appliances supporting interactive voice services. These devices are
typically deployed on a separate VLAN for ease of deployment and
enhanced security by isolation from data applications.
 Voice Signaling (conditional) - for use in network topologies that

require a different policy for the voice signaling than for the voice
media. This application type should not be advertised if all the same
network policies apply as those advertised in the Voice application
policy.
 Guest Voice - support a separate 'limited feature-set' voice service for

guest users and visitors with their own IP Telephony handsets and
other similar appliances supporting interactive voice services.
 Guest Voice Signaling (conditional) - for use in network topologies

that require a different policy for the guest voice signaling than for the
guest voice media. This application type should not be advertised if all
the same network policies apply as those advertised in the Guest
Voice application policy.
 Softphone Voice - for use by softphone applications on typical data

centric devices, such as PCs or laptops. This class of endpoints
frequently does not support multiple VLANs, if at all, and are typically
configured to use an 'untagged’ VLAN or a single 'tagged’ data specific
VLAN. When a network policy is defined for use with an 'untagged’
291
VLAN (see Tagged flag below), then the L2 priority field is ignored and
only the DSCP value has relevance.
 Video Conferencing - for use by dedicated Video Conferencing

equipment and other similar appliances supporting real-time
interactive video/audio services.
 Streaming Video - for use by broadcast or multicast based video

content distribution and other similar applications supporting streaming
video services that require specific network policy treatment. Video
applications relying on TCP with buffering would not be an intended
use of this application type.
 Video Signaling (conditional) - for use in network topologies that

require a separate policy for the video signaling than for the video
media. This application type should not be advertised if all the same
network policies apply as those advertised in the Video Conferencing
application policy.
 Tag Tag indicating whether the specified application type is using a 'tagged’ or an
'untagged’ VLAN.
 Untagged indicates that the device is using an untagged frame format

and as such does not include a tag header as defined by IEEE
802.1Q-2003. In this case, both the VLAN ID and the Layer 2 priority
fields are ignored and only the DSCP value has relevance.
 Tagged indicates that the device is using the IEEE 802.1Q tagged
frame format, and that both the VLAN ID and the Layer 2 priority
values are being used, as well as the DSCP value. The tagged format
includes an additional field, known as the tag header. The tagged

frame format also includes priority tagged frames as defined by IEEE
802.1Q-2003.
 VLAN ID VLAN identifier (VID) for the port as defined in IEEE 802.1Q-2003
 L2 Priority L2 Priority is the Layer 2 priority to be used for the specified application type. L2
Priority may specify one of eight priority levels (0 through 7), as defined by IEEE
802.1D-2004. A value of 0 represents use of the default priority as defined in
IEEE 802.1D-2004.
 DSCP DSCP value to be used to provide Diffserv node behavior for the specified
application type as defined in IETF RFC 2474. DSCP may contain one of 64
code point values (0 through 63). A value of 0 represents use of the default
DSCP value as defined in RFC 2475.
 Adding a new policy

Click to add a new policy. Specify the Application type,
Tag, VLAN ID, L2 Priority and DSCP for the new policy. Click "Save".
The number of policies supported is 32
292
Port Policies Configuration

Every port may advertise a unique set of network policies or different attributes for the same network policies, based on the
authenticated user identity or port configuration.
Object Description
 Port The port number for which the configuration applies.
 Policy ID The set of policies that shall apply for a given port. The set of policies is selected
by checkmarking the checkboxes that corresponds to the policies
Buttons
4.14.4 LLDP-MED Neighbor
This Page provides a status overview for all LLDP-MED neighbors. The displayed table contains a row for each port on which an
LLDP neighbor is detected. The LLDP-MED Neighbor Information screen in Figure 4-14-3 appears. The columns hold the
following information:
Figure 4-14-3: LLDP-MED Neighbor Information Page Screenshot
Fast start repeat count
Object Description
 Port The port on which the LLDP frame was received.
 Device Type LLDP-MED Devices are comprised of two primary Device Types: Network
Connectivity Devices and Endpoint Devices.
LLDP-MED Network Connectivity Device Definition
293
LLDP-MED Network Connectivity Devices, as defined in TIA-1057, provide
access to the IEEE 802 based LAN infrastructure for LLDP-MED Endpoint
Devices. An LLDP-MED Network Connectivity Device is a LAN access device
based on any of the following technologies:
1. LAN Switch/Router
2. IEEE 802.1 Bridge
3. IEEE 802.3 Repeater (included for historical reasons)
4. IEEE 802.11 Wireless Access Point
5. Any device that supports the IEEE 802.1AB and MED extensions defined by
TIA-1057 and can relay IEEE 802 frames via any method.
LLDP-MED Endpoint Device Definition

Within the LLDP-MED Endpoint Device category, the LLDP-MED scheme is
broken into further Endpoint Device Classes, as defined in the following.
Each LLDP-MED Endpoint Device Class is defined to build upon the capabilities
defined for the previous Endpoint Device Class. Fore-example will any
LLDP-MED Endpoint Device claiming compliance as a Media Endpoint (Class II)
also support all aspects of TIA-1057 applicable to Generic Endpoints (Class I),
and any LLDP-MED Endpoint Device claiming compliance as a Communication
Device (Class III) will also support all aspects of TIA-1057 applicable to both
Media Endpoints (Class II) and Generic Endpoints (Class I).
LLDP-MED Generic Endpoint (Class I)

The LLDP-MED Generic Endpoint (Class I) definition is applicable to all endpoint
products that require the base LLDP discovery services defined in TIA-1057,
however do not support IP media or act as an end-user communication
appliance. Such devices may include (but are not limited to) IP Communication
Controllers, other communication related servers, or any device requiring basic
services as defined in TIA-1057.
Discovery services defined in this class include LAN configuration, device
location, network policy, power management, and inventory management.
LLDP-MED Media Endpoint (Class II)

The LLDP-MED Media Endpoint (Class II) definition is applicable to all endpoint
products that have IP media capabilities however may or may not be associated
with a particular end user. Capabilities include all of the capabilities defined for
the previous Generic Endpoint Class (Class I), and are extended to include
aspects related to media streaming. Example product categories expected to
adhere to this class include (but are not limited to) Voice / Media Gateways,
Conference Bridges, Media Servers, and similar.
Discovery services defined in this class include media-type-specific network
layer policy discovery.
LLDP-MED Communication Endpoint (Class III)
294
The LLDP-MED Communication Endpoint (Class III) definition is applicable to all
endpoint products that act as end user communication appliances supporting IP
media. Capabilities include all of the capabilities defined for the previous Generic
Endpoint (Class I) and Media Endpoint (Class II) classes, and are extended to
include aspects related to end user devices. Example product categories
expected to adhere to this class include (but are not limited to) end user
communication appliances, such as IP Phones, PC-based softphones, or other
communication appliances that directly support the end user.
Discovery services defined in this class include provision of location identifier
(including ECS / E911 information), embedded L2 switch support, inventory
management
 LLDP-MED LLDP-MED Capabilities describes the neighbor unit's LLDP-MED capabilities.
Capabilities The possible capabilities are:
1. LLDP-MED capabilities
2. Network Policy
3. Location Identification
4. Extended Power via MDI - PSE
5. Extended Power via MDI - PD
6. Inventory
7. Reserved
 Application Type Application Type indicating the primary function of the application(s) defined for
this network policy, advertised by an Endpoint or Network Connectivity Device.
The poosible application types are shown below.
 Voice - for use by dedicated IP Telephony handsets and other similar

appliances supporting interactive voice services. These devices are typically
deployed on a separate VLAN for ease of deployment and enhanced
security by isolation from data applications.
 Voice Signaling - for use in network topologies that require a different policy
for the voice signaling than for the voice media.
 Guest Voice - to support a separate limited feature-set voice service for

guest users and visitors with their own IP Telephony handsets and other
similar appliances supporting interactive voice services.
 Guest Voice Signaling - for use in network topologies that require a different
policy for the guest voice signaling than for the guest voice media.
 Softphone Voice - for use by softphone applications on typical data centric

devices, such as PCs or laptops.
 Video Conferencing - for use by dedicated Video Conferencing equipment

and other similar appliances supporting real-time interactive video/audio
services.
 Streaming Video - for use by broadcast or multicast based video content
295
distribution and other similar applications supporting streaming video
services that require specific network policy treatment. Video applications
relying on TCP with buffering would not be an intended use of this
application type.
 Video Signaling - for use in network topologies that require a separate

policy for the video signaling than for the video media.
 Policy Policy indicates that an Endpoint Device wants to explicitly advertise that the
policy is required by the device. Can be either Defined or Unknown
 Unknown: The network policy for the specified application type is currently
unknown.
 Defined: The network policy is defined.

 TAG TAG is indicating whether the specified application type is using a tagged or an
untagged VLAN. Can be Tagged ot Untagged
 Untagged: The device is using an untagged frame format and as such does
not include a tag header as defined by IEEE 802.1Q-2003.
 Tagged: The device is using the IEEE 802.1Q tagged frame format
 VLAN ID VLAN ID is the VLAN identifier (VID) for the port as defined in IEEE
802.1Q-2003. A value of 1 through 4094 is used to define a valid VLAN ID. A
value of 0 (Priority Tagged) is used if the device is using priority tagged frames as
defined by IEEE 802.1Q-2003, meaning that only the IEEE 802.1D priority level
is significant and the default PVID of the ingress port is used instead.
 Priority Priority is the Layer 2 priority to be used for the specified application type.One of
eight priority levels (0 through 7)
 DSCP DSCP is the DSCP value to be used to provide Diffserv node behavior for the
specified application type as defined in IETF RFC 2474. Contain one of 64 code
point values (0 through 63).
 Auto-negotiation Auto-negotiation identifies if MAC/PHY auto-negotiation is supported by the link

partner.
 Auto-negotiation Auto-negotiation status identifies if auto-negotiation is currently enabled at the
status link partner. If Auto-negotiation is supported and Auto-negotiation status is

disabled, the 802.3 PMD operating mode will be determined the operational MAU
type field value rather than by auto-negotiation.
 Auto-negotiation Auto-negotiation Capabilities shows the link partners MAC/PHY capabilities.
Capabilities
Buttons
296
4.14.5 Neighbor
This Page provides a status overview for all LLDP neighbors. The displayed table contains a row for each port on which an
LLDP neighbor is detected. The LLDP Neighbor Information screen in Figure 4-14-4 appears.
Figure 4-14-4: LLDP Neighbor Information Page Screenshot
Object Description
 Local Port The port on which the LLDP frame was received.
 Chassis ID The Chassis ID is the identification of the neighbor's LLDP frames.
 Port ID The Port ID is the identification of the neighbor port.
 Port Description Port Description is the port description advertised by the neighbor unit.
 System Name System Name is the name advertised by the neighbor unit.
 System Capabilities System Capabilities describes the neighbor unit's capabilities. The possible
capabilities are:
1. Other
2. Repeater
3. Bridge
4. WLAN Access Point
5. Router
6. Telephone
7. DOCSIS cable device
8. Station only
9. Reserved
When a capability is enabled, the capability is followed by (+). If the capability is
disabled, the capability is followed by (-).
 Management Address Management Address is the neighbor unit's address that is used for higher layer
entities to assist the discovery by the network management. This could for
instance hold the neighbor's IP address.
297
4.14.6 Port Statistics
This Page provides an overview of all LLDP traffic. Two types of counters are shown. Global counters are counters that refer to
the whole switch, while local counters refers to counters for the currently selected switch. The LLDP Statistics screen in Figure
4-14-5 appears.
Figure 4-14-5: LLDP Statistics Page Screenshot
Global Counters
Object Description
 Neighbor entries were It also shows the time when the last entry was last deleted or added. It also
last changed shows the time elapsed since the last change was detected.
 Total Neighbors Shows the number of new entries added since switch reboot.
Entries Added
 Total Neighbors Shows the number of new entries deleted since switch reboot.
Entries Deleted
 Total Neighbors Shows the number of LLDP frames dropped due to that the entry table was full.
Entries Dropped
 Total Neighbors Shows the number of entries deleted due to Time-To-Live expiring.
Entries Aged Out
298
LLDP Statistics Local Counters

The displayed table contains a row for each port. The columns hold the following information:
Object Description
 Local Port The port on which LLDP frames are received or transmitted.
 Tx Frames The number of LLDP frames transmitted on the port.
 Rx Frames The number of LLDP frames received on the port.
 Rx Errors The number of received LLDP frames containing some kind of error.
 Frames Discarded If an LLDP frame is received on a port, and the switch's internal table has run full,
the LLDP frame is counted and discarded. This situation is known as "Too Many
Neighbors" in the LLDP standard. LLDP frames require a new entry in the table
when the Chassis ID or Remote Port ID is not already contained within the table.
Entries are removed from the table when a given port links down, an LLDP
shutdown frame is received, or when the entry ages out.
 TLVs Discarded Each LLDP frame can contain multiple pieces of information, known as TLVs
(TLV is short for "Type Length Value"). If a TLV is malformed, it is counted and
discarded.
 TLVs Unrecognized The number of well-formed TLVs, but with an unknown type value.
 Org. Discarded The number of organizationally TLVs received.
 Age-Outs Each LLDP frame contains information about how long time the LLDP
information is valid (age-out time). If no new LLDP frame is received within the
age out time, the LLDP information is removed, and the Age-Out counter is
incremented.
Buttons
: Clears the local counters. All counters (including global counters) are cleared upon reboot.
299
4.15 Network Diagnostics

This section provide the Physical layer and IP layer network diagnostics tools for troubleshoot. The diagnostic tools are
designed for network manager to help them quickly diagnose problems between point to point and better service customers.
Use the Diagnastics menu items to display and configure basic administrative details of the Managed Switch. Under System the
following topics are provided to configure and view the system information:
This section has the following items:
 Ping
 IPv6 Ping
 Remote IP Ping
 Cable Diagnostics
PING
The ping and IPv6 ping allow you to issue ICMP PING packets to troubleshoot IP connectivity issues. The Managed Switch
transmit ICMP packets, and the sequence number and roundtrip time are displayed upon reception of a reply.
Cable Diagnostics
The Cable Diagnostics performing tests on copper cables. These functions have the ability to identify the cable length and
operating conditions, and to isolate a variety of common faults that can occur on the Cat5 twisted-pair cabling. There might be
two statuses as follow:
 If the link is established on the twisted-pair interface in 1000BASE-T mode, the Cable Diagnostics can run without
disruption of the link or of any data transfer.
 If the link is established in 100BASE-TX or 10BASE-T, the Cable Diagnostics cause the link to drop while the
diagnostics are running.
After the diagnostics are finished, the link is reestablished. And the following functions are available.
 Coupling between cable pairs.
 Cable pair termination
 Cable Length
300
4.15.1 Ping
This Page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues.
After you press “Start”, 5 ICMP packets are transmitted, and the sequence number and roundtrip time are displayed upon
reception of a reply. The Page refreshes automatically until responses to all packets are received, or until a timeout occurs. The
ICMP Ping screen in Figure 4-15-1 appears.
Figure 4-15-1: ICMP Ping Page Screenshot

Object Description
 IP Address The destination IP Address.
 Ping Length The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes.
Be sure the target IP Address is within the same network subnet of the Managed Switch, or you had
setup the correct gateway IP address.
Buttons
: Click to transmit ICMP packets.
: Click to re-start diagnostics with PING.
301
4.15.2 IPv6 Ping
This Page allows you to issue ICMPv6 PING packets to troubleshoot IPv6 connectivity issues.
After you press “Start”, 5 ICMPv6 packets are transmitted, and the sequence number and roundtrip time are displayed upon
ICMPv6 Ping screen in Figure 4-15-2 appears.
Figure 4-15-2: ICMPv6 Ping Page Screenshot
Object Description
 IP Address The destination IP Address.
 Ping Length The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes.
 Egress Interface The VLAN ID (VID) of the specific egress IPv6 interface which ICMP packet
goes. The given VID ranges from 1 to 4094 and will be effective only when the
corresponding IPv6 interface is valid. When the egress interface is not given,
PING6 finds the best match interface for destination.
Do not specify egress interface for loopback address.
Do specify egress interface for link-local or multicast address.
Buttons
: Click to transmit ICMP packets.
: Click to re-start diagnostics with PING.
302
4.15.3 Remote IP Ping Test

This Page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues on special port.
After you press “Test”, 5 ICMP packets are transmitted, and the sequence number and roundtrip time are displayed upon
ICMP Ping screen in Figure 4-15-3 appears.
Figure 4-15-3: Remote IP Ping Test Page Screenshot
Object Description
 Remote IP Address The destination IP Address.
 Ping Size The payload size of the ICMP packet. Values range from 8 bytes to 1400 bytes.
 Result Display the ping result.
Buttons
: Clears the IP Address and the result of ping value.
303
4.15.4 Cable Diagnostics

This Page is used for running the Cable Diagnostics.
Press to run the diagnostics. This will take approximately 5 seconds. If all ports are selected, this can take approximately 15
seconds. When completed, the Page refreshes automatically, and you can view the cable diagnostics results in the cable status
table. Note that Cable Diagnostics is only accurate for cables of length 7 - 140 meters.
10 and 100 Mbps ports will be linked down while running cable diagnostic. Therefore, running cable diagnastic on a 10 or 100
Mbps management port will cause the switch to stop responding until VeriPHY is complete. The VeriPHY Cable Diagnostics
Figure 4-15-4: VeriPHY Cable Diagnostics Page Screenshot
Object Description
 Port The port where you are requesting Cable Diagnostics.
 Description Display per port description.
304
 Cable Status Port:

Port number.
Pair:
The status of the cable pair.
OK - Correctly terminated pair
Open - Open pair
Short - Shorted pair
Short A - Cross-pair short to pair A
Short B - Cross-pair short to pair B
Short C - Cross-pair short to pair C
Short D - Cross-pair short to pair D
Cross A - Abnormal cross-pair coupling with pair A
Cross B - Abnormal cross-pair coupling with pair B
Cross C - Abnormal cross-pair coupling with pair C
Cross D - Abnormal cross-pair coupling with pair D
Length:
The length (in meters) of the cable pair. The resolution is 3 meters
Buttons
: Click to run the diagnostics.
305
4.16 Loop Protection

This chapter describes enabling loop protection function that provides loop protection to prevent broadcast loops in Managed
Switch.
4.16.1 Configuration
This Page allows the user to inspect the current Loop Protection configurations, and possibly change them as well; screen in
Figure 4-17-1: Loop Protection Configuration Page Screenshot
General Settings
Object Description
 Enable Loop Controls whether loop protections is enabled (as a whole).
Protection
306
 Transmission Time The interval between each loop protection PDU sent on each port. valid values
are 1 to 10 seconds.
 Shutdown Time The period (in seconds) for which a port will be kept disabled in the event of a
loop is detected (and the port action shuts down the port). Valid values are 0 to
604800 seconds (7 days). A value of zero will keep a port disabled (until next
device restart).
Port Configuration
Object Description
 Port The switch port number of the port.
 Enable Controls whether loop protection is enabled on this switch port.
 Action Configures the action performed when a loop is detected on a port. Valid values
are Shutdown Port, Shutdown Port and Log or Log Only.
 Tx Mode Controls whether the port is actively generating loop protection PDU's, or
whether it is just passively looking for looped PDU's.
Buttons
4.16.2 Loop Protection Status
This Page displays the loop protection port status of the switch; screen in Figure 4-17-2 appears.
Figure 4-17-2: Loop Protection Status Screenshot
Object Description
 Port The Managed Switch port number of the logical port.
307
 Action The currently configured port action.
 Transmit The currently configured port transmit mode.
 Loops The number of loops detected on this port.
 Status The current loop protection status of the port.
 Loop Whether a loop is currently detected on the port.
 Time of Last Loop The time of the last loop event detected.
Buttons
308
4.17 RMON
RMON is the most important expansion of the standard SNMP. RMON is a set of MIB definitions, used to define standard
network monitor functions and interfaces, enabling the communication between SNMP management terminals and remote
monitors. RMON provides a highly efficient method to monitor actions inside the subnets.
MID of RMON consists of 10 groups. The switch supports the most frequently used group 1, 2, 3 and 9:
 Statistics: Maintain basic usage and error statistics for each subnet monitored by the Agent.
 History: Record periodical statistic samples available from Statistics.
 Alarm: Allow management console users to set any count or integer for sample intervals and alert thresholds for
RMON Agent records.
 Event: A list of all events generated by RMON Agent.
Alarm depends on the implementation of Event. Statistics and History display some current or history subnet statistics. Alarm
and Event provide a method to monitor any integer data change in the network, and provide some alerts upon abnormal events
(sending Trap or record in logs).
4.17.1 RMON Alarm Configuration
Configure RMON Alarm table on this Page. The entry index key is ID.; screen in Figure 4-18-1 appears.
Figure 4-18-1: RMON Alarm Configuration Page Screenshot
Object Description
 ID Indicates the index of the entry. The range is from 1 to 65535.
 Interval Indicates the interval in seconds for sampling and comparing the rising and
falling threshold. The range is from 1 to 2^31-1.
 Variable Indicates the particular variable to be sampled, the possible variables are:
 InOctets: The total number of octets received on the interface, including

framing characters.
 InUcastPkts: The number of uni-cast packets delivered to a higher-layer

protocol.
309
 InNUcastPkts: The number of broad-cast and multi-cast packets delivered

to a higher-layer protocol.
 InDiscards: The number of inbound packets that are discarded even the
packets are normal.
 InErrors: The number of inbound packets that contained errors preventing

them from being deliverable to a higher-layer protocol.
 InUnknownProtos: the number of the inbound packets that were discarded

because of the unknown or un-support protocol.
 OutOctets: The number of octets transmitted out of the interface , including

framing characters.
 OutUcastPkts: The number of uni-cast packets that request to transmit.

 OutNUcastPkts: The number of broad-cast and multi-cast packets that
request to transmit.
 OutDiscards: The number of outbound packets that are discarded event the
packets is normal.
 OutErrors: The The number of outbound packets that could not be

transmitted because of errors.
 OutQLen: The length of the output packet queue (in packets).

 Sample Type The method of sampling the selected variable and calculating the value to be
compared against the thresholds, possible sample types are:
 Absolute: Get the sample directly.

 Delta: Calculate the difference between samples (default).
 Value The value of the statistic during the last sampling period.
 Startup Alarm The method of sampling the selected variable and calculating the value to be
compared against the thresholds, possible sample types are:
 RisingTrigger alarm when the first value is larger than the rising threshold.
 FallingTrigger alarm when the first value is less than the falling threshold.
 RisingOrFallingTrigger alarm when the first value is larger than the rising
threshold or less than the falling threshold (default).
 Rising Threshold Rising threshold value (-2147483648-2147483647).
 Rising Index Rising event index (1-65535).
 Falling Threshold Falling threshold value (-2147483648-2147483647)
 Falling Index Falling event index (1-65535).
Buttons
310
4.17.2 RMON Alarm Status
This Page provides an overview of RMON Alarm entries. Each Page shows up to 99 entries from the Alarm table, default being
20, selected through the "entries per Page" input field. When first visited, the web Page will show the first 20 entries from the
beginning of the Alarm table. The first displayed will be the one with the lowest ID found in the Alarm table; screen in Figure
4-18-2 appears.
Figure 4-18-2: RMON Alarm Overview Page Screenshot
Object Description
 ID Indicates the index of Alarm control entry.
 Interval Indicates the interval in seconds for sampling and comparing the rising and
falling threshold.
 Variable Indicates the particular variable to be sampled
 Sample Type The method of sampling the selected variable and calculating the value to be
compared against the thresholds.
 Value The value of the statistic during the last sampling period.
 Startup Alarm The alarm that may be sent when this entry is first set to valid.
 Rising Threshold Rising threshold value.
 Rising Index Rising event index.
 Falling Threshold Falling threshold value.
 Falling Index Falling event index.
Buttons
: Updates the table, starting from the first entry in the Alarm Table, i.e. the entry with the lowest ID.
311
4.17.3 RMON Event Configuration
Configure RMON Event table on this Page. The entry index key is ID; screen in Figure 4-18-3 appears.
Figure 4-18-4: RMON Event Configuration Page Screenshot
Object Description
 Desc Indicates this event, the string length is from 0 to 127, default is a null string.
 Type Indicates the notification of the event, the possible types are:
 none: The total number of octets received on the interface, including framing
characters.
 log: The number of uni-cast packets delivered to a higher-layer protocol.

 snmptrap: The number of broad-cast and multi-cast packets delivered to a
higher-layer protocol.
 logandtrap: The number of inbound packets that are discarded even the
packets are normal.
 Community Specify the community when trap is sent, the string length is from 0 to 127,
default is "public".
 Event Last Time Indicates the value of sysUpTime at the time this event entry last generated an
event.
Buttons
312
4.17.4 RMON Event Status
This Page provides an overview of RMON Event table entries.Each Page shows up to 99 entries from the Event table, default
being 20, selected through the "entries per Page" input field. When first visited, the web Page will show the first 20 entries from
the beginning of the Event table. The first displayed will be the one with the lowest Event Index and Log Index found in the Event
table table; screen in Figure 4-18-5 appears.
Figure 4-18-5: RMON Event Overview Page Screenshot
Object Description
 Event Index Indicates the index of the event entry.
 Log Index Indicates the index of the log entry.
 LogTime Indicates Event log time.
 LogDescription Indicates the Event description.
Buttons
: Updates the table starting from the first entry in the Alarm Table, i.e. the entry with the lowest ID.
313
4.17.5 RMON History Configuration
Configure RMON History table on this Page. The entry index key is ID; screen in Figure 4-18-6 appears.
Figure 4-18-6: RMON History Configuration Page Screenshot
Object Description
 Data Source Indicates the port ID which wants to be monitored.
 Interval Indicates the interval in seconds for sampling the history statistics data. The
range is from 1 to 3600, default value is 1800 seconds.
 Buckets Indicates the maximum data entries associated this History control entry stored in
RMON. The range is from 1 to 3600, default value is 50.
 Buckets Granted The number of data shall be saved in the RMON.
Buttons
314
4.17.6 RMON History Status
This Page provides an detail of RMON history entries; screen in Figure 4-18-7 appears.
Figure 4-18-7: RMON History Overview Page Screenshot
Object Description
 History Index Indicates the index of History control entry.
 Sample Index Indicates the index of the data entry associated with the control entry.
 Sample Start The value of sysUpTime at the start of the interval over which this sample was
measured.
 Drop The total number of events in which packets were dropped by the probe due to
lack of resources.
 Octets The total number of octets of data (including those in bad packets) received on
the network.
 Pkts The total number of packets (including bad packets, broadcast packets, and
multicast packets) received.
 Broadcast The total number of good packets received that were directed to the broadcast
address.
 Multicast The total number of good packets received that were directed to a multicast
address.
CRC Errors The total number of packets received that had a length (excluding framing bits,
but including FCS octets) of between 64 and 1518 octets, inclusive, but had
either a bad Frame Check Sequence (FCS) with an integral number of octets
(FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
 Undersize The total number of packets received that were less than 64 octets.
 Oversize The total number of packets received that were longer than 1518 octets.
 Frag. The number of frames which size is less than 64 octets received with invalid
CRC.
 Jabb. The number of frames which size is larger than 64 octets received with invalid
CRC.
 Coll. The best estimate of the total number of collisions on this Ethernet segment.
315
 Utilization The best estimate of the mean physical layer network utilization on this interface
during this sampling interval, in hundredths of a percent.
Buttons
: Updates the table, starting from the first entry in the History table, i.e., the entry with the lowest History
Index and Sample Index
4.17.7 RMON Statistics Configuration
Configure RMON Statistics table on this Page. The entry index key is ID; screen in Figure 4-18-8 appears.
Figure 4-18-8: RMON Statistics Configuration Page Screenshot
Object Description
 Data Source Indicates the port ID which wants to be monitored.
Buttons
316
4.17.8 RMON Statistics Status
This Page provides an overview of RMON Statistics entries. Each Page shows up to 99 entries from the Statistics table, default
being 20, selected through the "entries per Page" input field. When first visited, the web Page will show the first 20 entries from
the beginning of the Statistics table. The first displayed will be the one with the lowest ID found in the Statistics table; screen in
Figure 4-18-9: RMON Statistics Status Overview Page Screenshot
Object Description
 ID Indicates the index of Statistics entry.
 Data Source (ifIndex) The port ID which wants to be monitored.
 Drop The total number of events in which packets were dropped by the probe due to
lack of resources.
 Octets The total number of octets of data (including those in bad packets) received on
the network.
 Pkts The total number of packets (including bad packets, broadcast packets, and
multicast packets) received.
 Broadcast The total number of good packets received that were directed to the broadcast
address.
 Multicast The total number of good packets received that were directed to a multicast
address.
 CRC Errors The total number of packets received that had a length (excluding framing bits,
but including FCS octets) of between 64 and 1518 octets.
 Undersize The total number of packets received that were less than 64 octets.
 Oversize The total number of packets received that were longer than 1518 octets.
 Frag. The number of frames which size is less than 64 octets received with invalid
CRC.
 Jabb. The number of frames which size is larger than 64 octets received with invalid
CRC.
317
 Coll. The best estimate of the total number of collisions on this Ethernet segment.
 64 Bytes The total number of packets (including bad packets) received that were 64 octets
in length.
 65~127 The total number of packets (including bad packets) received that were between
65 to 127 octets in length.
Buttons
: Updates the table, starting from the first entry in the Alarm Table, i.e. the entry with the lowest ID.
318
5. SWITCH OPERATION
5.1 Address Table

The Managed Switch is implemented with an address table. This address table composed of many entries. Each entry is used
to store the address information of some node in network, including MAC address, port no, etc. This in-formation comes from
the learning process of Managed Switch.
5.2 Learning
When one packet comes in from any port, the Managed Switch will record the source address, port no. And the other related
information in address table. This information will be used to decide either forwarding or filtering for future packets.
5.3 Forwarding & Filtering

When one packet comes from some port of the Managed Switch, it will also check the destination address besides the source
address learning. The Managed Switch will lookup the address-table for the destination address. If not found, this packet will be
forwarded to all the other ports except the port, which this packet comes in. And these ports will transmit this packet to the
network it connected. If found, and the destination address is located at different port from this packet comes in, the Managed
Switch will forward this packet to the port where this destination address is located according to the information from address
table. But, if the destination address is located at the same port with this packet comes in, then this packet will be filtered.
Thereby increasing the network throughput and availability.
5.4 Store-and-Forward
Store-and-Forward is one type of packet-forwarding techniques. A Store-and-Forward Managed Switch stores the incoming
frame in an internal buffer, do the complete error checking before transmission. Therefore, no error packets occurrence, it is the
best choice when a network needs efficiency and stability.
The Managed Switch scans the destination address from the packet-header, searches the routing table pro-vided for the
incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for connecting servers
directly to the network, thereby increasing throughput and availability. How-ever, the switch is most commonly used to segment
existence hubs, which nearly always improves overall performance. An Ethernet Switching can be easily configured in any
Ethernet network environment to signifi-cantly boost bandwidth using conventional cabling and adapters.
Due to the learning function of the Managed Switch, the source address and corresponding port number of each incoming and
outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address
is on the same segment as the source address. This confines network traffic to its respective domain and reduce the overall
load on the network.
The Managed Switch performs "Store and Fforward" therefore, no error packets occur. More reliably, it reduces the
re-transmission rate. No packet loss will occur.
319
5.5 Auto-Negotiation
The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth
when a connection is established with another network device (usually at Power On or Reset). This is done by detect the modes
and speeds at the second of both device is connected and capable of, both 10BASE-T and 100BASE-TX devices can connect
with the port in either Half- or Full-Duplex mode. 1000BASE-T can be only connected in Full-duplex mode.
320
User's Manual of GS-5220 Series
User’s Manual of WGSW-48040HP
6. TROUBLESHOOTING
This chapter contains information to help you solve issues. If the Managed Switch is not functioning properly, make sure
the Managed Switch was set up according to instructions in this manual.
■ The Link LED is not lit
Solution:
Check the cable connection and remove duplex mode of the Managed Switch
■ Some stations cannot talk to other stations located on the other port
Solution:
Please check the VLAN settings, trunk settings, or port enabled / disabled status.
■ Performance is bad
Solution:
Check the full duplex status of the Managed Switch. If the Managed Switch is set to full duplex and the partner is set to
half duplex, then the performance will be poor. Please also check the in/out rate of the port.
■ Why the Switch doesn't connect to the network
Solution:
1. Check the LNK/ACT LED on the switch
2. Try another port on the Switch
3. Make sure the cable is installed properly
4. Make sure the cable is the right type
5. Turn off the power. After a while, turn on power again
■ 1000BASE-T port link LED is lit, but the traffic is irregular
Solution:
Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to
change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.
■ Switch does not power up
Solution:
1. AC power cord not inserted or faulty
2. Check that the AC power cord is inserted correctly
3. Replace the power cord If the cord is inserted correctly, check that the AC power source is working by
connecting a different device in place of the switch.
4. If that device works, refer to the next step.
5. If that device does not work, check the AC power
321
User's Manual of GS-5220 Series
User’s Manual of WGSW-48040HP
APPENDIX A: Networking Connection
A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T
PIN NO MDI MDI-X
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly
forbidden, is beyond the scope of this standard.
A.2 10/100Mbps, 10/100BASE-TX

When connecting your Switch to another Fast Ethernet switch, a bridge or a hub, a straight or crossover cable is
necessary. Each port of the Switch supports auto-MDI/MDI-X detection. That means you can directly connect the Switch
to any Ethernet devices without making a crossover cable. The following table and diagram show the standard RJ45
receptacle/ connector and their pin assignments:
RJ45 Connector pin assignment

MDI MDI-X
PIN NO
Media Dependant Interface Media Dependant Interface-Cross
1 Tx + (transmit) Rx + (receive)
2 Tx - (transmit) Rx - (receive)
3 Rx + (receive) Tx + (transmit)
4, 5 Not used
6 Rx - (receive) Tx - (transmit)
7, 8 Not used
322
User's
User’s ManualofofWGSW-48040HP
Manual GS-5220 Series
The standard cable, RJ45 pin assignment
6 321
6 321
6 3 21
The standard RJ45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and
color of straight cable and crossover cable connection:
Straight Cable SIDE 1 SIDE 2

1 2 3 4 5 6 7 8 SIDE 1 1 = White / Orange 1 = White / Orange
2 = Orange 2 = Orange
3 = White / Green 3 = White / Green
4 = Blue 4 = Blue
5 = White / Blue 5 = White / Blue
6 = Green 6 = Green
7 = White / Brown 7 = White / Brown
1 2 3 4 5 6 7 8 SIDE 2 8 = Brown 8 = Brown
Crossover Cable SIDE 1 SIDE 2

1 2 3 4 5 6 7 8 SIDE 1 1 = White / Orange 1 = White / Green
2 = Orange 2 = Green
3 = White / Green 3 = White / Orange
4 = Blue 4 = Blue
5 = White / Blue 5 = White / Blue
6 = Green 6 = Orange
7 = White / Brown 7 = White / Brown
1 2 3 4 5 6 7 8 SIDE 2 8 = Brown 8 = Brown
Figure A-1: Straight-through and Crossover Cable
Please make sure your connected cables are with the same pin assignment and color as the above picture before
deploying the cables into your network.
323
APPENDIX B : GLOSSARY
A
ACE
ACE is an acronym for Access Control Entry. It describes access permission associated with a particular ACE ID.
There are three ACE frame types (Ethernet Type, ARP, and IPv4) and two ACE actions (permit and deny). The ACE
also contains many detailed, different parameter options that are available for individual application.
ACL
ACL is an acronym for Access Control List. It is the list table of ACEs, containing access control entries that specify
individual users or groups permitted or denied to specific traffic objects, such as a process or a program.
Each accessible traffic object contains an identifier to its ACL. The privileges determine whether there are specific
traffic object access rights.
ACL implementations can be quite complex, for example, when the ACEs are prioritized for the various situation. In
networking, the ACL refers to a list of service ports or network services that are available on a host or server, each with
a list of hosts or servers permitted or denied to use the service. ACL can generally be configured to control inbound
traffic, and in this context, they are similar to firewalls.
There are 3 web-Pages associated with the manual ACL configuration:
ACL|Access Control List: The web Page shows the ACEs in a prioritized way, highest (top) to lowest (bottom).
Default the table is empty. An ingress frame will only get a hit on one ACE even though there are more matching ACEs.
The first matching ACE will take action (permit/deny) on that frame and a counter associated with that ACE is
incremented. An ACE can be associated with a Policy, 1 ingress port, or any ingress port (the whole switch). If an ACE
Policy is created then that Policy can be associated with a group of ports under the "Ports" web-Page. There are
number of parameters that can be configured with an ACE. Read the Web Page help text to get further information for
each of them. The maximum number of ACEs is 64.
ACL|Ports: The ACL Ports configuration is used to assign a Policy ID to an ingress port. This is useful to group ports to
obey the same traffic rules. Traffic Policy is created under the "Access Control List" - Page. You can you also set up
specific traffic properties (Action / Rate Limiter / Port copy, etc) for each ingress port. They will though only apply if the
frame gets past the ACE matching without getting matched. In that case a counter associated with that port is
incremented. See the Web Page help text for each specific port property.
324
ACL|Rate Limiters: Under this Page you can configure the rate limiters. There can be 15 different rate limiters, each
ranging from 1-1024K packets per seconds. Under "Ports" and "Access Control List" web-Pages you can assign a
Rate Limiter ID to the ACE(s) or ingress port(s).
AES
AES is an acronym for Advanced Encryption Standard. The encryption key protocol is applied in 802.1i standard to
improve WLAN security. It is an encryption standard by the U.S. government, which will replace DES and 3DES. AES
has a fixed block size of 128 bits and a key size of 128, 192, or 256 bits.
AMS
AMS is an acronym for Auto Media Select. AMS is used for dual media ports (ports supporting both copper (cu) and
fiber (SFP) cables. AMS automatically determines if a SFP or a CU cable is inserted and switches to the corresponding
media. If both SFP and cu cables are inserted, the port will select the prefered media.
APS
APS is an acronym for Automatic Protection Switching. This protocol is used to secure that switching is done
bidirectional in the two ends of a protection group, as defined in G.8031.
Aggregation
Using multiple ports in parallel to increase the link speed beyond the limits of a port and to increase the redundancy for
higher availability.
(Also Port Aggregation, Link Aggregation).
ARP
ARP is an acronym for Address Resolution Protocol. It is a protocol that used to convert an IP address into a physical
address, such as an Ethernet address. ARP allows a host to communicate with other hosts when only the Internet
address of its neighbors is known. Before using IP, the host sends a broadcast ARP request containing the Internet
address of the desired destination system.
ARP Inspection
ARP Inspection is a secure feature. Several types of attacks can be launched against a host or devices connected to
Layer 2 networks by "poisoning" the ARP caches. This feature is used to block such attacks. Only valid ARP requests
and responses can go through the switch device.
Auto-Negotiation
325
Auto-negotiation is the process where two different devices establish the mode of operation and the speed settings
that can be shared by those devices for a link.
C
CC
CC is an acronym for Continuity Check. It is a MEP functionality that is able to detect loss of continuity in a network by
transmitting CCM frames to a peer MEP.
CCM
CCM is an acronym for Continuity Check Message. It is a OAM frame transmitted from a MEP to it's peer MEP and
used to implement CC functionality.
CDP
CDP is an acronym for Cisco Discovery Protocol.
D
DEI
DEI is an acronym for Drop Eligible Indicator. It is a 1-bit field in the VLAN tag.
DES
DES is an acronym for Data Encryption Standard. It provides a complete description of a mathematical algorithm for
encrypting (enciphering) and decrypting (deciphering) binary coded information.
Encrypting data converts it to an unintelligible form called cipher. Decrypting cipher converts the data back to its
original form called plaintext. The algorithm described in this standard specifies both enciphering and deciphering
operations which are based on a binary number called a key.
DHCP
DHCP is an acronym for Dynamic Host Configuration Protocol. It is a protocol used for assigning dynamic IP
addresses to devices on a network.
DHCP used by networked computers (clients) to obtain IP addresses and other parameters such as the default
gateway, subnet mask, and IP addresses of DNS servers from a DHCP server.
326
The DHCP server ensures that all IP addresses are unique, for example, no IP address is assigned to a second client
while the first client's assignment is valid (its lease has not expired). Therefore, IP address pool management is done
by the server and not by a human network administrator.
Dynamic addressing simplifies network administration because the software keeps track of IP addresses rather than
requiring an administrator to manage the task. This means that a new computer can be added to a network without the
hassle of manually assigning it a unique IP address.
DHCP Relay
DHCP Relay is used to forward and to transfer DHCP messages between the clients and the server when they are not
on the same subnet domain.
The DHCP option 82 enables a DHCP relay agent to insert specific information into a DHCP request packets when
forwarding client DHCP packets to a DHCP server and remove the specific information from a DHCP reply packets
when forwarding server DHCP packets to a DHCP client. The DHCP server can use this information to implement IP
address or other assignment policies. Specifically the option works by setting two sub-options: Circuit ID (option 1) and
Remote ID (option2). The Circuit ID sub-option is supposed to include information specific to which circuit the request
came in on. The Remote ID sub-option was designed to carry information relating to the remote host end of the circuit.
The definition of Circuit ID in the switch is 4 bytes in length and the format is "vlan_id" "module_id" "port_no". The
parameter of "vlan_id" is the first two bytes represent the VLAN ID. The parameter of "module_id" is the third byte for
the module ID. The parameter of "port_no" is the fourth byte and it means the port number.
The Remote ID is 6 bytes in length, and the value is equal the DHCP relay agents MAC address.
DHCP Snooping
DHCP Snooping is used to block intruder on the untrusted ports of the switch device when it tries to intervene by
injecting a bogus DHCP reply packet to a legitimate conversation between the DHCP client and server.
DNS
DNS is an acronym for Domain Name System. It stores and associates many types of information with domain names.
Most importantly, DNS translates human-friendly domain names and computer hostnames into computer-friendly IP
addresses. For example, the domain name www.example.com might translate to 192.168.0.1.
DoS
DoS is an acronym for Denial of Service. In a denial-of-service (DoS) attack, an attacker attempts to prevent legitimate
users from accessing information or services. By targeting at network sites or network connection, an attacker may be
able to prevent network users from accessing email, web sites, online accounts (banking, etc.), or other services that
rely on the affected computer.
Dotted Decimal Notation
327
Dotted Decimal Notation refers to a method of writing IP addresses using decimal numbers and dots as separators
between octets.
An IPv4 dotted decimal address has the form x.y.z.w, where x, y, z, and w are decimal numbers between 0 and 255.
DSCP
DSCP is an acronym for Differentiated Services Code Point. It is a field in the header of IP packets for packet
classification purposes.
E
EEE
EEE is an abbreviation for Energy Efficient Ethernet defined in IEEE 802.3az.
EPS
EPS is an abbreviation for Ethernet Protection Switching defined in ITU/T G.8031.
Ethernet Type
Ethernet Type, or EtherType, is a field in the Ethernet MAC header, defined by the Ethernet networking standard. It is
used to indicate which protocol is being transported in an Ethernet frame.
F
FTP
FTP is an acronym for File Transfer Protocol. It is a transfer protocol that uses the Transmission Control Protocol (TCP)
and provides file writing and reading. It also provides directory service and security features.
Fast Leave
IGMP snooping Fast Leave processing allows the switch to remove an interface from the forwarding-table entry without
first sending out group specific queries to the interface. The VLAN interface is pruned from the multicast tree for the
multicast group specified in the original leave message. Fast-leave processing ensures optimal bandwidth
management for all hosts on a switched network, even when multiple multicast groups are in use simultaneously.
H
HTTP
HTTP is an acronym for Hypertext Transfer Protocol. It is a protocol that used to transfer or convey information on the
World Wide Web (WWW).
HTTP defines how messages are formatted and transmitted, and what actions Web servers and browsers should take
in response to various commands. For example, when you enter a URL in your browser, this actually sends an HTTP
command to the Web server directing it to fetch and transmit the requested Web Page. The other main standard that
controls how the World Wide Web works is HTML, which covers how Web Pages are formatted and displayed.
328
Any Web server machine contains, in addition to the Web Page files it can serve, an HTTP daemon, a program that is
designed to wait for HTTP requests and handle them when they arrive. The Web browser is an HTTP client, sending
requests to server machines. An HTTP client initiates a request by establishing a Transmission Control Protocol (TCP)
connection to a particular port on a remote host (port 80 by default). An HTTP server listening on that port waits for the
client to send a request message.
HTTPS
HTTPS is an acronym for Hypertext Transfer Protocol over Secure Socket Layer. It is used to indicate a secure HTTP
connection.
HTTPS provide authentication and encrypted communication and is widely used on the World Wide Web for
security-sensitive communication such as payment transactions and corporate logons.
HTTPS is really just the use of Netscape's Secure Socket Layer (SSL) as a sublayer under its regular HTTP
application layering. (HTTPS uses port 443 instead of HTTP port 80 in its interactions with the lower layer, TCP/IP.)
SSL uses a 40-bit key size for the RC4 stream encryption algorithm, which is considered an adequate degree of
encryption for commercial exchange.
I
ICMP
ICMP is an acronym for Internet Control Message Protocol. It is a protocol that generated the error response,
diagnostic or routing purposes. ICMP messages generally contain information about routing difficulties or simple
exchanges such as time-stamp or echo transactions. For example, the PING command uses ICMP to test an Internet
connection.
IEEE 802.1X
IEEE 802.1X is an IEEE standard for port-based Network Access Control. It provides authentication to devices
attached to a LAN port, establishing a point-to-point connection or preventing access from that port if authentication
fails. With 802.1X, access to all switch ports can be centrally controlled from a server, which means that authorized
users can use the same credentials for authentication from any point within the network.
IGMP
IGMP is an acronym for Internet Group Management Protocol. It is a communications protocol used to manage the
membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish
multicast group memberships. It is an integral part of the IP multicast specification, like ICMP for unicast connections.
IGMP can be used for online video and gaming, and allows more efficient use of resources when supporting these
uses.
IGMP Querier
A router sends IGMP Query messages onto a particular link. This router is called the Querier.
329
IMAP
IMAP is an acronym for Internet Message Access Protocol. It is a protocol for email clients to retrieve email messages
from a mail server.
IMAP is the protocol that IMAP clients use to communicate with the servers, and SMTP is the protocol used to
transport mail to an IMAP server.
The current version of the Internet Message Access Protocol is IMAP4. It is similar to Post Office Protocol version 3
(POP3), but offers additional and more complex features. For example, the IMAP4 protocol leaves your email
messages on the server rather than downloading them to your computer. If you wish to remove your messages from
the server, you must use your mail client to generate local folders, copy messages to your local hard drive, and then
delete and expunge the messages from the server.
IP
IP is an acronym for Internet Protocol. It is a protocol used for communicating data across a internet network.
IP is a "best effort" system, which means that no packet of information sent over it is assured to reach its destination in
the same condition it was sent. Each device connected to a Local Area Network (LAN) or Wide Area Network (WAN) is
given an Internet Protocol address, and this IP address is used to identify the device uniquely among all other devices
connected to the extended network.
The current version of the Internet protocol is IPv4, which has 32-bits Internet Protocol addresses allowing for in
excess of four billion unique addresses. This number is reduced drastically by the practice of webmasters taking
addresses in large blocks, the bulk of which remain unused. There is a rather substantial movement to adopt a new
version of the Internet Protocol, IPv6, which would have 128-bits Internet Protocol addresses. This number can be
represented roughly by a three with thirty-nine zeroes after it. However, IPv4 is still the protocol of choice for most of
the Internet.
IPMC
IPMC is an acronym for IP MultiCast.
IP Source Guard
IP Source Guard is a secure feature used to restrict IP traffic on DHCP snooping untrusted ports by filtering traffic
based on the DHCP Snooping Table or manually configured IP Source Bindings. It helps prevent IP spoofing attacks
when a host tries to spoof and use the IP address of another host.
L
LACP
LACP is an IEEE 802.3ad standard protocol. The Link Aggregation Control Protocol, allows bundling several physical
ports together to form a single logical port.
330
LLDP
LLDP is an IEEE 802.1ab standard protocol.
The Link Layer Discovery Protocol(LLDP) specified in this standard allows stations attached to an IEEE 802 LAN to
advertise, to other stations attached to the same IEEE 802 LAN, the major capabilities provided by the system
incorporating that station, the management address or addresses of the entity or entities that provide management of
those capabilities, and the identification of the stations point of attachment to the IEEE 802 LAN required by those
management entity or entities. The information distributed via this protocol is stored by its recipients in a standard
Management Information Base (MIB), making it possible for the information to be accessed by a Network Management
System (NMS) using a management protocol such as the Simple Network Management Protocol (SNMP).
LLDP-MED
LLDP-MED is an extendsion of IEEE 802.1ab and is defined by the telecommunication industry association
(TIA-1057).
LOC
LOC is an acronym for Loss Of Connectivity and is detected by a MEP and is indicating lost connectivity in the network.
Can be used as a switch criteria by EPS
M
MAC Table
Switching of frames is based upon the DMAC address contained in the frame. The switch builds up a table that maps
MAC addresses to switch ports for knowing which ports the frames should go to ( based upon the DMAC address in
the frame ). This table contains both static and dynamic entries. The static entries are configured by the network
administrator if the administrator wants to do a fixed mapping between the DMAC address and switch ports.
The frames also contain a MAC address ( SMAC address ), which shows the MAC address of the equipment sending
the frame. The SMAC address is used by the switch to automatically update the MAC table with these dynamic MAC
addresses. Dynamic entries are removed from the MAC table if no frame with the corresponding SMAC address have
been seen after a configurable age time.
MEP
MEP is an acronym for Maintenance Entity Endpoint and is an endpoint in a Maintenance Entity Group (ITU-T Y.1731).
MD5
MD5 is an acronym for Message-Digest algorithm 5. MD5 is a message digest algorithm, used cryptographic hash
function with a 128-bit hash value. It was designed by Ron Rivest in 1991. MD5 is officially defined in RFC 1321 - The
MD5 Message-Digest Algorithm.
331
Mirroring
For debugging network problems or monitoring network traffic, the switch system can be configured to mirror frames
from multiple ports to a mirror port. (In this context, mirroring a frame is the same as copying the frame.)
Both incoming (source) and outgoing (destination) frames can be mirrored to the mirror port.
MLD
MLD is an acronym for Multicast Listener Discovery for IPv6. MLD is used by IPv6 routers to discover multicast
listeners on a directly attached link, much as IGMP is used in IPv4. The protocol is embedded in ICMPv6 instead of
using a separate protocol.
MVR
Multicast VLAN Registration (MVR) is a protocol for Layer 2 (IP)-networks that enables multicast-traffic from a source
VLAN to be shared with subscriber-VLANs.
The main reason for using MVR is to save bandwidth by preventing duplicate multicast streams being sent in the core
network, instead the stream(s) are received on the MVR-VLAN and forwarded to the VLANs where hosts have
requested it/them(Wikipedia).
N
NAS
NAS is an acronym for Network Access Server. The NAS is meant to act as a gateway to guard access to a protected
source. A client connects to the NAS, and the NAS connects to another resource asking whether the client's supplied
credentials are valid. Based on the answer, the NAS then allows or disallows access to the protected resource. An
example of a NAS implementation is IEEE 802.1X.
NetBIOS
NetBIOS is an acronym for Network Basic Input/Output System. It is a program that allows applications on separate
computers to communicate within a Local Area Network (LAN), and it is not supported on a Wide Area Network (WAN).
The NetBIOS giving each computer in the network both a NetBIOS name and an IP address corresponding to a
different host name, provides the session and transport services described in the Open Systems Interconnection (OSI)
model.
NFS
NFS is an acronym for Network File System. It allows hosts to mount partitions on a remote system and use them as
though they are local file systems.
332
NFS allows the system administrator to store resources in a central location on the network, providing authorized users
continuous access to them, which means NFS supports sharing of files, printers, and other resources as persistent
storage over a computer network.
NTP
NTP is an acronym for Network Time Protocol, a network protocol for synchronizing the clocks of computer systems.
NTP uses UDP (datagrams) as transport layer.
O
OAM
OAM is an acronym for Operation Administration and Maintenance.
It is a protocol described in ITU-T Y.1731 used to implement carrier ethernet functionality. MEP functionality like CC
and RDI is based on this.
Optional TLVs.
A LLDP frame contains multiple TLVs
For some TLVs it is configurable if the switch shall include the TLV in the LLDP frame. These TLVs are known as
optional TLVs. If an optional TLVs is disabled the corresponding information is not included in the LLDP frame.
OUI
OUI is the organizationally unique identifier. An OUI address is a globally unique identifier assigned to a vendor by
IEEE. You can determine which vendor a device belongs to according to the OUI address which forms the first 24 bits
of a MAC address.
P
PCP
PCP is an acronym for Priority Code Point. It is a 3-bit field storing the priority level for the 802.1Q frame. It is also
known as User Priority.
PD
PD is an acronym for Powered Device. In a PoE> system the power is delivered from a PSE ( power sourcing
equipment ) to a remote device. The remote device is called a PD.
333
PHY
PHY is an abbreviation for Physical Interface Transceiver and is the device that implement the Ethernet physical layer
(IEEE-802.3).
PING
Ping is a program that sends a series of packets over a network or the Internet to a specific computer in order to
generate a response from that computer. The other computer responds with an acknowledgment that it received the
packets. Ping was created to verify whether a specific computer on a network or the Internet exists and is connected.
ping uses Internet Control Message Protocol (ICMP) packets. The PING Request is the packet from the origin
computer, and the PING Reply is the packet response from the target.
Policer
A policer can limit the bandwidth of received frames. It is located in front of the ingress queue.
POP3
POP3 is an acronym for Post Office Protocol version 3. It is a protocol for email clients to retrieve email messages from
a mail server.
POP3 is designed to delete mail on the server as soon as the user has downloaded it. However, some
implementations allow users or an administrator to specify that mail be saved for some period of time. POP can be
thought of as a "store-and-forward" service.
An alternative protocol is Internet Message Access Protocol (IMAP). IMAP provides the user with more capabilities for
retaining e-mail on the server and for organizing it in folders on the server. IMAP can be thought of as a remote file
server.
POP and IMAP deal with the receiving of e-mail and are not to be confused with the Simple Mail Transfer Protocol
(SMTP). You send e-mail with SMTP, and a mail handler receives it on your recipient's behalf. Then the mail is read
using POP or IMAP. IMAP4 and POP3 are the two most prevalent Internet standard protocols for e-mail retrieval.
Virtually all modern e-mail clients and servers support both.
PPPoE
PPPoE is an acronym for Point-to-Point Protocol over Ethernet.
It is a network protocol for encapsulating Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly
with ADSL services where individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro
Ethernet networks (Wikipedia).
Private VLAN
In a private VLAN, communication between ports in that private VLAN is not permitted. A VLAN can be configured as a
private VLAN.
334
PTP
PTP is an acronym for Precision Time Protocol, a network protocol for synchronizing the clocks of computer systems.
Q
QCE
QCE is an acronym for QoS Control Entry. It describes QoS class associated with a particular QCE ID.
There are six QCE frame types: Ethernet Type, VLAN, UDP/TCP Port, DSCP, TOS, and Tag Priority. Frames can be
classified by one of 4 different QoS classes: "Low", "Normal", "Medium", and "High" for individual application.
QCL
QCL is an acronym for QoS Control List. It is the list table of QCEs, containing QoS control entries that classify to a
specific QoS class on specific traffic objects.
Each accessible traffic object contains an identifier to its QCL. The privileges determine specific traffic object to specific
QoS class.
QL
QL In SyncE this is the Quality Level of a given clock source. This is received on a port in a SSM indicating the quality
of the clock received in the port.
QoS
QoS is an acronym for Quality of Service. It is a method to guarantee a bandwidth relationship between individual
applications or protocols.
A communications network transports a multitude of applications and data, including high-quality video and
delay-sensitive data such as real-time voice. Networks must provide secure, predictable, measurable, and sometimes
guaranteed services.
Achieving the required QoS becomes the secret to a successful end-to-end business solution. Therefore, QoS is the
set of techniques to manage network resources.
QoS class
Every incoming frame is classified to a QoS class, which is used throughout the device for providing queuing,
scheduling and congestion control guarantees to the frame according to what was configured for that specific QoS
class. There is a one to one mapping between QoS class, queue and priority. A QoS class of 0 (zero) has the lowest
priority.
335
R
RARP
RARP is an acronym for Reverse Address Resolution Protocol. It is a protocol that is used to obtain an IP address for a
given hardware address, such as an Ethernet address. RARP is the complement of ARP.
RADIUS
RADIUS is an acronym for Remote Authentication Dial In User Service. It is a networking protocol that provides
centralized access, authorization and accounting management for people or computers to connect and use a network
service.
RDI
RDI is an acronym for Remote Defect Indication. It is a OAM functionallity that is used by a MEP to indicate defect
detected to the remote peer MEP
Router Port
A router port is a port on the Ethernet switch that leads switch towards the Layer 3 multicast device.
RSTP
In 1998, the IEEE with document 802.1w introduced an evolution of STP: the Rapid Spanning Tree Protocol, which
provides for faster spanning tree convergence after a topology change. Standard IEEE 802.1D-2004 now incorporates
RSTP and obsoletes STP, while at the same time being backwards-compatible with STP.
S
SAMBA
Samba is a program running under UNIX-like operating systems that provides seamless integration between UNIX and
Microsoft Windows machines. Samba acts as file and print servers for Microsoft Windows, IBM OS/2, and other SMB
client machines. Samba uses the Server Message Block (SMB) protocol and Common Internet File System (CIFS),
which is the underlying protocol used in Microsoft Windows networking.
Samba can be installed on a variety of operating system platforms, including Linux, most common Unix platforms,
OpenVMS, and IBM OS/2.
Samba can also register itself with the master browser on the network so that it would appear in the listing of hosts in
Microsoft Windows "Neighborhood Network".
SHA
SHA is an acronym for Secure Hash Algorithm. It designed by the National Security Agency (NSA) and published by
the NIST as a U.S. Federal Information Processing Standard. Hash algorithms compute a fixed-length digital
representation (known as a message digest) of an input data sequence (the message) of any length.
336
Shaper
A shaper can limit the bandwidth of transmitted frames. It is located after the ingress queues.
SMTP
SMTP is an acronym for Simple Mail Transfer Protocol. It is a text-based protocol that uses the Transmission Control
Protocol (TCP) and provides a mail service modeled on the FTP file transfer service. SMTP transfers mail messages
between systems and notifications regarding incoming mail.
SNAP
The SubNetwork Access Protocol (SNAP) is a mechanism for multiplexing, on networks using IEEE 802.2 LLC, more
protocols than can be distinguished by the 8-bit 802.2 Service Access Point (SAP) fields. SNAP supports identifying
protocols by Ethernet type field values; it also supports vendor-private protocol identifier.
SNMP
SNMP is an acronym for Simple Network Management Protocol. It is part of the Transmission Control Protocol/Internet
Protocol (TCP/IP) protocol for network management. SNMP allow diverse network objects to participate in a network
management architecture. It enables network management systems to learn network problems by receiving traps or
change notices from network devices implementing SNMP.
SNTP
SNTP is an acronym for Simple Network Time Protocol, a network protocol for synchronizing the clocks of computer
systems. SNTP uses UDP (datagrams) as transport layer.
SPROUT
Stack Protocol using ROUting Technology. An advanced protocol for almost instantaneous discovery of topology
changes within a stack as well as election of a master switch. SPROUT also calculates parameters for setting up each
switch to perform shortest path forwarding within the stack.
SSID
Service Set Identifier is a name used to identify the particular 802.11 wireless LANs to which a user wants to attach. A
client device will receive broadcast messages from all access points within range advertising their SSIDs, and can
choose one to connect to based on pre-configuration, or by displaying a list of SSIDs in range and asking the user to
select one (wikipedia).
SSH
SSH is an acronym for Secure SHell. It is a network protocol that allows data to be exchanged using a secure channel
between two networked devices. The encryption used by SSH provides confidentiality and integrity of data over an
insecure network. The goal of SSH was to replace the earlier rlogin, TELNET and rsh protocols, which did not provide
strong authentication or guarantee confidentiality (Wikipedia).
SSM
SSM In SyncE this is an abbreviation for Synchronization Status Message and is containing a QL indication.
337
STP
Spanning Tree Protocol is an OSI layer-2 protocol which ensures a loop free topology for any bridged LAN. The
original STP protocol is now obsoleted by RSTP.
SyncE
SyncE Is an abbreviation for Synchronous Ethernet. This functionality is used to make a network 'clock frequency'
synchronized. Not to be confused with real time clock synchronized (IEEE 1588).
T
TACACS+
TACACS+ is an acronym for Terminal Acess Controller Access Control System Plus. It is a networking protocol which
provides access control for routers, network access servers and other networked computing devices via one or more
centralized servers. TACACS+ provides separate authentication, authorization and accounting services.
Tag Priority
Tag Priority is a 3-bit field storing the priority level for the 802.1Q frame.
TCP
TCP is an acronym for Transmission Control Protocol. It is a communications protocol that uses the Internet Protocol
(IP) to exchange the messages between computers.
The TCP protocol guarantees reliable and in-order delivery of data from sender to receiver and distinguishes data for
multiple connections by concurrent applications (for example, Web server and e-mail server) running on the same
host.
The applications on networked hosts can use TCP to create connections to one another. It is known as a
connection-oriented protocol, which means that a connection is established and maintained until such time as the
message or messages to be exchanged by the application programs at each end have been exchanged. TCP is
responsible for ensuring that a message is divided into the packets that IP manages and for reassembling the packets
back into the complete message at the other end.
Common network applications that use TCP include the World Wide Web (WWW), e-mail, and File Transfer Protocol
(FTP).
TELNET
TELNET is an acronym for TELetype NETwork. It is a terminal emulation protocol that uses the Transmission Control
Protocol (TCP) and provides a virtual connection between TELNET server and TELNET client.
TELNET enables the client to control the server and communicate with other servers on the network. To start a Telnet
session, the client user must log in to a server by entering a valid username and password. Then, the client user can
enter commands through the Telnet program just as if they were entering commands directly on the server console.
338
TFTP
TFTP is an acronym for Trivial File Transfer Protocol. It is transfer protocol that uses the User Datagram Protocol (UDP)
and provides file writing and reading, but it does not provides directory service and security features.
ToS
ToS is an acronym for Type of Service. It is implemented as the IPv4 ToS priority control. It is fully decoded to
determine the priority from the 6-bit ToS field in the IP header. The most significant 6 bits of the ToS field are fully
decoded into 64 possibilities, and the singular code that results is compared against the corresponding bit in the IPv4
ToS priority control bit (0~63).
TLV
TLV is an acronym for Type Length Value. A LLDP frame can contain multiple pieces of information. Each of these
pieces of information is known as TLV.
TKIP
TKIP is an acronym for Temporal Key Integrity Protocol. It used in WPA to replace WEP with a new encryption
algorithm. TKIP comprises the same encryption engine and RC4 algorithm defined for WEP. The key used for
encryption in TKIP is 128 bits and changes the key used for each packet.
U
UDP
UDP is an acronym for User Datagram Protocol. It is a communications protocol that uses the Internet Protocol (IP) to
exchange the messages between computers.
UDP is an alternative to the Transmission Control Protocol (TCP) that uses the Internet Protocol (IP). Unlike TCP, UDP
does not provide the service of dividing a message into packet datagrams, and UDP doesn't provide reassembling and
sequencing of the packets. This means that the application program that uses UDP must be able to make sure that the
entire message has arrived and is in the right order. Network applications that want to save processing time because
they have very small data units to exchange may prefer UDP to TCP.
UDP provides two services not provided by the IP layer. It provides port numbers to help distinguish different user
requests and, optionally, a checksum capability to verify that the data arrived intact.
Common network applications that use UDP include the Domain Name System (DNS), streaming media applications
such as IPTV, Voice over IP (VoIP), and Trivial File Transfer Protocol (TFTP).
UPnP
UPnP is an acronym for Universal Plug and Play. The goals of UPnP are to allow devices to connect seamlessly and to
simplify the implementation of networks in the home (data sharing, communications, and entertainment) and in
corporate environments for simplified installation of computer components
339
User Priority
User Priority is a 3-bit field storing the priority level for the 802.1Q frame.
V
VLAN
Virtual LAN. A method to restrict communication between switch ports. VLANs can be used for the following
applications:
VLAN unaware switching: This is the default configuration. All ports are VLAN unaware with Port VLAN ID 1 and
members of VLAN 1. This means that MAC addresses are learned in VLAN 1, and the switch does not remove or
insert VLAN tags.
VLAN aware switching: This is based on the IEEE 802.1Q standard. All ports are VLAN aware. Ports connected to
VLAN aware switches are members of multiple VLANs and transmit tagged frames. Other ports are members of one
VLAN, set up with this Port VLAN ID, and transmit untagged frames.
Provider switching: This is also known as Q-in-Q switching. Ports connected to subscribers are VLAN unaware,
members of one VLAN, and set up with this unique Port VLAN ID. Ports connected to the service provider are VLAN
aware, members of multiple VLANs, and set up to tag all frames. Untagged frames received on a subscriber port are
forwarded to the provider port with a single VLAN tag. Tagged frames received on a subscriber port are forwarded to
the provider port with a double VLAN tag.
VLAN ID
VLAN ID is a 12-bit field specifying the VLAN to which the frame belongs.
Voice VLAN
Voice VLAN is VLAN configured specially for voice traffic. By adding the ports with voice devices attached to voice
VLAN, we can perform QoS-related configuration for voice data, ensuring the transmission priority of voice traffic and
voice quality.
W
WEP
WEP is an acronym for Wired Equivalent Privacy. WEP is a deprecated algorithm to secure IEEE 802.11 wireless
networks. Wireless networks broadcast messages using radio, so are more susceptible to eavesdropping than wired
networks. When introduced in 1999, WEP was intended to provide confidentiality comparable to that of a traditional
wired network (Wikipedia).
WiFi
WiFi is an acronym for Wireless Fidelity. It is meant to be used generically when referring of any type of 802.11 network,
whether 802.11b, 802.11a, dual-band, etc. The term is promulgated by the Wi-Fi Alliance.
340
WPA
WPA is an acronym for Wi-Fi Protected Access. It was created in response to several serious weaknesses researchers
had found in the previous system , Wired Equivalent Privacy (WEP). WPA implements the majority of the IEEE 802.11i
standard, and was intended as an intermediate measure to take the place of WEP while 802.11i was prepared. WPA is
specifically designed to also work with pre-WPA wireless network interface cards (through firmware upgrades), but not
necessarily with first generation wireless access points. WPA2 implements the full standard, but will not work with
some older network cards (Wikipedia).
WPA-PSK
WPA-PSK is an acronym for Wi-Fi Protected Access - Pre Shared Key. WPA was designed to enhance the security of
wireless networks. There are two flavors of WPA: enterprise and personal. Enterprise is meant for use with an IEEE
802.1X authentication server, which distributes different keys to each user. Personal WPA utilizes less scalable
'pre-shared key' (PSK) mode, where every allowed computer is given the same passphrase. In PSK mode, security
depends on the strength and secrecy of the passphrase. The design of WPA is based on a Draft 3 of the IEEE 802.11i
standard (Wikipedia)
WPA-Radius
WPA-Radius is an acronym for Wi-Fi Protected Access - Radius (802.1X authentication server). WPA was designed to
enhance the security of wireless networks. There are two flavors of WPA: enterprise and personal. Enterprise is meant
for use with an IEEE 802.1X authentication server, which distributes different keys to each user. Personal WPA utilizes
less scalable 'pre-shared key' (PSK) mode, where every allowed computer is given the same passphrase. In PSK
mode, security depends on the strength and secrecy of the passphrase. The design of WPA is based on a Draft 3 of
the IEEE 802.11i standard (Wikipedia)
WPS
WPS is an acronym for Wi-Fi Protected Setup. It is a standard for easy and secure establishment of a wireless home
network. The goal of the WPS protocol is to simplify the process of connecting any home device to the wireless
network (Wikipedia).
WRED
WRED is an acronym for Weighted Random Early Detection. It is an active queue management mechanism that
provides preferential treatment of higher priority frames when traffic builds up within a queue. A frame's DP level is
used as input to WRED. A higher DP level assigned to a frame results in a higher probability that the frame is dropped
during times of congestion.
WTR
WTR is an acronym for Wait To Restore. This is the time a fail on a resource has to be 'not active' before restoration
back to this (previously failing) resource is done.
341
EC Declaration of Conformity
For the following equipment:
*Type of Product : 24 100/1000X SFP Slots with 8 Shared TP Managed Switch

*Model Number : GS-5220-16S8C,GS-5220-16S8CR
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (2010+AC: 2011)

EN 61000-3-2 (2006+A1:2009+A2:2009)
EN 61000-3-3 (2013)
EN 55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2007+A2:2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2013)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 8th, Aug., 2014

Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION

e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
For the following equipment:
*Type of Product : L2+ 44-Port 100/1000BASE-X SFP + 4-Port Gigabit TP/SFP

Managed Switch
*Model Number : GS-5220-44S4C
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (2010+AC: 2011)

EN 61000-3-2 (2006+A1:2009+A2:2009)
EN 61000-3-3 (2013)
EN 55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2007+A2:2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2013)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 13th, Feb., 2015

Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION

e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

EM GS 5220 Series v1.1

Uploaded by

Copyright:

Available Formats

EM GS 5220 Series v1.1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EM GS 5220 Series v1.1

Uploaded by

Copyright:

Available Formats

User’s Manual of GS-5220 Series

Energy Saving Note of the Device

Model: GS-5220 Series

Revision: 1.0 (January, 2015)

Part No: EM-GS-5220-series _v1.0

1.1 Packet Contents ...........................................................................................................................................9

1.2 Product Description ...................................................................................................................................10

1.3 How to Use This Manual ............................................................................................................................12

1.4 Product Features........................................................................................................................................13

1.5 Product Specifications ..............................................................................................................................16

2.1 Hardware Description ................................................................................................................................22

2.1.2 LED Indications ...................................................................................................................................................24

2.1.3 Switch Rear Panel ...............................................................................................................................................28

2.2 Installing the Switch...................................................................................................................................30

2.2.2 Rack Mounting.....................................................................................................................................................31

2.2.3 Installing the SFP/SFP+ Transceiver ...................................................................................................................32

3. SWITCH MANAGEMENT .................................................................................................... 36

3.2 Management Access Overview .................................................................................................................37

3.3 Administration Console .............................................................................................................................38

3.4 Web Management .......................................................................................................................................39

3.5 SNMP-based Network Management .........................................................................................................40

3.6 PLANET Smart Discovery Utility ..............................................................................................................40

4. WEB CONFIGURATION ...................................................................................................... 42

4.1 Main Web Page ...........................................................................................................................................44

4.2.2 IP Configuration ...................................................................................................................................................48

4.2.3 IP Status ..............................................................................................................................................................50

4.2.4 Users Configuration .............................................................................................................................................51

4.2.5 Privilege Levels ...................................................................................................................................................54

4.2.6 NTP Configuration ...............................................................................................................................................55

4.2.7 Time Configuration ..............................................................................................................................................56

4.2.8 UPnP ...................................................................................................................................................................58

4.2.9 DHCP Relay ........................................................................................................................................................60

4.2.10 DHCP Relay Statistics .......................................................................................................................................61

4.2.11 CPU Load ..........................................................................................................................................................63

4.2.12 System Log........................................................................................................................................................64

4.2.13 Detailed Log ......................................................................................................................................................65

4.2.14 Remote Syslog ..................................................................................................................................................66

4.2.15 SMTP Configuration ..........................................................................................................................................67

4.2.16 Web Firmware Upgrade.....................................................................................................................................68

4.2.17 TFTP Firmware Upgrade ...................................................................................................................................69

4.2.18 Save Startup Config...........................................................................................................................................70

4.2.19 Configuration Download ....................................................................................................................................70

4.2.20 Configuration Upload .........................................................................................................................................71

4.2.21 Configuration Activate........................................................................................................................................71

4.2.22 Configuration Delete ..........................................................................................................................................72

4.2.23 Image Select......................................................................................................................................................72

4.2.24 Factory Default ..................................................................................................................................................73

4.2.25 System Reboot ..................................................................................................................................................74

4.3 Simple Network Management Protocol....................................................................................................75

4.3.2 SNMP System Configuration ...............................................................................................................................76

4.3.3 SNMP Trap Configuration....................................................................................................................................78

4.3.4 SNMP System Information ..................................................................................................................................80

4.3.5 SNMPv3 Configuration ........................................................................................................................................81

4.3.5.1 SNMPv3 Communities ..............................................................................................................................81

4.3.5.3 SNMPv3 Groups........................................................................................................................................83

4.3.5.4 SNMPv3 Views..........................................................................................................................................84

4.3.5.5 SNMPv3 Access ........................................................................................................................................85

4.4 Port Management .......................................................................................................................................87

4.4.2 Port Statistics Overview .......................................................................................................................................89

4.4.3 Port Statistics Detail.............................................................................................................................................90