CPU 1515-2 PN ___________________

Preface

(6ES7515-2AM00-0AB0) ___________________
Documentation guide 1

___________________
2
SIMATIC Product overview

___________________
Connecting up 3
S7-1500
CPU 1515-2 PN Interrupts, error messages,
(6ES7515-2AM00-0AB0) ___________
4
diagnostics and system
alarms

Manual ___________________
Technical specifications 5

___________________
Dimensional drawing A

12/2014
A5E32332431-AB
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION
indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:

WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Siemens AG A5E32332431-AB Copyright © Siemens AG 2014.

Division Digital Factory Ⓟ 12/2014 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Preface

Purpose of the documentation

This manual supplements the system manual of the S7-1500 automation system and the
function manuals. All cross-system functions are described in the system manual and in the
function manuals.
The information provided in this manual and the system manual allows you to commission
the CPU 1515-2 PN.

Conventions
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".

Also read the notes labeled as follows:

Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.

Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. You can find more information about industrial security on the Internet
(http://www.siemens.com/industrialsecurity).
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. You can find more information on the Internet
(http://support.automation.siemens.com).

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

4 Manual, 12/2014, A5E32332431-AB
Table of contents

Preface ................................................................................................................................................... 4
1 Documentation guide .............................................................................................................................. 6
2 Product overview .................................................................................................................................... 8
2.1 Application ................................................................................................................................ 8
2.2 How it works ............................................................................................................................10
2.3 Properties ................................................................................................................................11
2.4 Operating and display elements .............................................................................................14
2.4.1 Front view of the module with closed front panel ...................................................................14
2.4.2 Front view of the module without front panel ..........................................................................16
2.4.3 Rear view of the module .........................................................................................................17
2.5 Mode selector switch ..............................................................................................................17
2.6 Functions ................................................................................................................................18
2.6.1 PROFINET IO .........................................................................................................................18
2.6.2 PROFIenergy ..........................................................................................................................19
2.6.3 Memory reset ..........................................................................................................................19
2.6.4 Restoring the factory settings of the CPU...............................................................................21
3 Connecting up....................................................................................................................................... 24
4 Interrupts, error messages, diagnostics and system alarms ................................................................... 28
4.1 Status and error display of the CPU .......................................................................................28
5 Technical specifications ........................................................................................................................ 31
A Dimensional drawing ............................................................................................................................. 41

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 5
Documentation guide 1
The documentation for the SIMATIC S7-1500 automation system and the SIMATIC
ET 200MP distributed I/O system is arranged into three areas.
This arrangement enables you to access the specific content you require.

Basic information
System Manual and Getting Started describe in detail the configuration, installation, wiring
and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7 online
help supports you in the configuration and programming.

Device information
Product manuals contain a compact description of the module-specific information, such as
properties, terminal diagrams, characteristics and technical specifications.

General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
S7-1500 and ET 200MP systems, e.g. diagnostics, communication, Motion Control, Web
server.
You can download the documentation free of charge from the Internet
(http://www.automation.siemens.com/mcms/industrial-automation-systems-
simatic/en/manual-overview/tech-doc-controllers/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

6 Manual, 12/2014, A5E32332431-AB
 Documentation guide

Manual Collection S7-1500/ET 200MP

The Manual Collection contains the complete documentation on the SIMATIC S7-1500
automation system and the ET 200MP distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(http://support.automation.siemens.com/WW/view/en/86140384).

My Documentation Manager
The My Documentation Manager is used to combine entire manuals or only parts of these to
your own manual.
You can export the manual as PDF file or in a format that can be edited later.
You can find the My Documentation Manager on the Internet
(http://support.automation.siemens.com/WW/view/en/38715968).

Applications & Tools

Applications & Tools supports you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus in individual products.
You can find Applications & Tools on the Internet
(http://support.automation.siemens.com/WW/view/en/20208582).

CAx Download Manager

The CAx Download Manager is used to access the current product data for your CAx or CAe
systems.
You configure your own download package with a few clicks.
In doing so you can select:
● Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
● Manuals, characteristics, operating manuals, certificates
● Product master data
You can find the CAx Download Manager on the Internet
(http://support.automation.siemens.com/WW/view/en/42455541).

TIA Selection Tool

With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 7
Product overview 2
2.1 Application
The CPUs of the SIMATIC S7-1500 controller family offer best possible performance
combined with excellent usability. With their integrated PROFINET/PROFIBUS interfaces,
the Web server and integrated functionalities, such as Motion Control, PID controller and
temperature controller, trace support, the CPUs are predestined for numerous applications in
automation engineering.

Performance segments
The CPUs can be used for smaller and mid-range applications, as well as for the high-end
area of machine and plant automation.

CPU Performance segment PROFIBUS PROFINET Work Processing time

interfaces interfaces memory for bit
operations
CPU 1511-1 PN Standard CPU for smaller to mid-range -- 1 1.15 MB 60 ns
applications
CPU 1511F-1 PN Fail-safe CPU for smaller to mid-range -- 1 1.23 MB 60 ns
applications
CPU 1513-1 PN Standard CPU for mid-range -- 1 1.8 MB 40 ns
applications
CPU 1513F-1 PN Fail-safe CPU for mid-range -- 1 1.95 MB 40 ns
applications
CPU 1515-2 PN Standard CPU for mid-range to large -- 2 3.5 MB 30 ns
applications
CPU 1515F-2 PN Fail-safe CPU for mid-range to large -- 2 3.75 MB 30 ns
applications
CPU 1516-3 PN/DP Standard CPU for high-end applica- 1 2 6 MB 10 ns
tions and communication tasks
CPU 1516F-3 PN/DP Fail-safe CPU for high-end applications 1 2 6.5 MB 10 ns
and communication tasks
CPU 1517-3 PN/DP Standard CPU for demanding 1 2 10 MB 2 ns
applications and communication tasks
CPU 1517F-3 PN/DP Fail-safe CPU for demanding 1 2 11 MB 2 ns
applications and communication tasks
CPU 1518-4 PN/DP Standard CPU for high-performance 1 3 24 MB 1 ns
applications, demanding communica-
tion tasks and very short reaction times
CPU 1518F-4 PN/DP Fail-safe CPU for high-performance 1 3 26 MB 1 ns
applications, demanding communica-
tion tasks and very short reaction times

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

8 Manual, 12/2014, A5E32332431-AB
 Product overview
2.1 Application

Integrated technology functions

The CPUs of the SIMATIC S7-1500 family support Motion Control functions. STEP 7 offers
PLCopen standardized blocks for configuring and connecting a drive to the CPU. Motion
Control supports speed, positioning and synchronous axes, as well as external encoders.
For effective commissioning, diagnostics and fast optimization of drives and controls, the
SIMATIC S7-1500 controller family offers extensive trace functions for all CPU tags.
In addition to drive integration, the SIMATIC S7-1500 has extensive control functionalities,
such as easy-to-configure blocks for automatic optimization of the controller parameters for
optimized control quality.
Technology modules also implement functions such as high-speed counting, position
detection and measuring functions for 24 V signals up to 200 kHz.
Due to the integrated technology function, the CPUs are suitable, for example, for pumps,
fans, mixers, conveyor belts, lifting platforms, gate control systems, building management
systems, synchronized axes, cross cutters, etc.

Security Integrated
The CPUs are aimed at users that require the maximum possible plant security.
In combination with STEP 7, each CPU offers password-based know-how protection against
unauthorized reading or modifying of the program blocks.
The copy protection provides high-performance protection against unauthorized reproduction
of program blocks. The copy protection can be used to link individual blocks on the SIMATIC
memory card with their serial numbers. The block can only be executed if the configured
memory card is inserted in the CPU.
In addition, four different authorization levels in the CPUs can be used to assign different
access right to various user groups.
Improved manipulation protection allows the CPUs to detect changed or unauthorized
transfers of the engineering data.

Safety Integrated
The fail-safe CPUs are aimed at users that want to implement demanding standard and
fail-safe applications in both a centralized and a distributed manner.
These fail-safe CPUs allow the processing of standard and safety programs on a single
CPU. This allows fail-safe data to be evaluated in the standard user program. This
integration thus provides the system advantages and the extensive functionality of SIMATIC
also for fail-safe applications.
The fail-safe CPUs are certified for use in safety mode up to:
● Safety class (Safety Integrity Level) SIL 3 according to IEC 61508:2010
● Performance Level (PL) e and Category 4 according to ISO 13849-1:2006 or according to
EN ISO 13849-1:2008
Additional password protection for F-configuration and F-program is set up for IT security.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 9
Product overview
2.2 How it works

Design and handling

The design and handling of the CPUs is very straightforward and offers the greatest possible
user friendliness. All CPUs have a display. The display provides information on order
numbers, firmware version and serial numbers of all connected modules. The IP address of
the CPU and other network settings can be set directly on site, without a programming
device. The display shows occurring errors messages directly as plain text multi-lingual
messages and helps you to reduce downtimes.

System diagnostics
Integrated system diagnostics is activated by default for the CPUs. The different diagnostic
types are configured instead of programmed. System diagnostics information is shown
uniformly and in plain text on the display of the CPU, in STEP 7, on the HMI and on the Web
server, even for alarms related to drives. This information is available in RUN mode, but also
in STOP mode of the CPU. An automatic update of the diagnostics information is performed
when you configure new hardware components.

2.2 How it works

The CPU contains the operating system and executes the user program. The user program
is located on the SIMATIC memory card and is processed in the work memory of the CPU.
The PROFINET interfaces on the CPU allow simultaneous communication with PROFINET
devices, PROFINET controllers, HMI devices, programming devices, other controllers and
other systems. CPU 1515-2 PN supports operation as an IO controller and I-device.

IO controller
As an IO controller, CPU 1515-2 PN sends and receives data and signals from the
connected IO devices within a PROFINET IO system. You can operate the CPU with a
maximum of 256 IO devices, of which a maximum of 64 may be IRT (Isochronous Realtime)
devices.

I-device
In the "I-device" (intelligent IO device) function, CPU 1515-2 PN not only controls its own
central modules, but also acts as an I-device, exchanging data with a higher-level IO
controller. CPU 1515-2 PN thus fulfills the role of an intelligent pre-processing unit for
sub-processes.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

10 Manual, 12/2014, A5E32332431-AB
 Product overview
2.3 Properties

2.3 Properties

Article number
6ES7515-2AM00-0AB0

View of the module

The following figure shows the CPU 1515-2 PN.

Figure 2-1 CPU 1515-2 PN

Note
Protective film
Note that a protective film is attached to the display of the CPU when shipped from the
factory. Remove the protective film if necessary.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 11
Product overview
2.3 Properties

Properties
The CPU 1515-2 PN has the following technical properties:
● Communication:
– Interfaces
CPU 1515-2 PN has two PROFINET interfaces.
The 1st PROFINET interface (X1) has two ports (P1R and P2R). In addition to
PROFINET basic functionality, it also supports PROFINET IO RT (Realtime) and IRT
(Isochronous Realtime). PROFINET IO communication or real-time settings can only
be configured at this interface. Port 1 and port 2 can also be used as ring ports for the
configuration of redundant ring structures in Ethernet (media redundancy).
The 2nd PROFINET interface (X2) features a port (P1) and supports PROFINET basic
functionality, which means no IO controller/IO device role. PROFINET basic
functionality supports HMI communication, communication with the configuration
system, communication with a higher-level network (backbone, router, Internet) and
communication with another machine or automation cell.

Note
IP subnets
The IP subnets of both interfaces must be different. This means that the subnets of
the IP address of both interfaces must differ from each other.

● Integrated Web server:

The CPU is accessible via an integrated Web server for diagnostic purposes. You can
read the following information with the Web server:
– Start page with general CPU information
– Identification information
– Contents of the diagnostics buffer
– Querying module information
– Alarms (without acknowledgment option)
– Information about communication
– PROFINET topology
– Tag status
– Watch tables
– Memory usage
– Data logs (if used)

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

12 Manual, 12/2014, A5E32332431-AB
 Product overview
2.3 Properties

● Integrated technology:
– Motion Control
PLC-Open blocks for programming motion functionality using PROFINET IO IRT with
the PROFIdrive interface.
The functionality supports speed-controlled axes, positioning axes, synchronous axes
and external encoders.
– Integrated closed-loop control functionality
- Universal PID controller and 3-point controller with integrated tuning
- Integrated temperature controller
● Trace functionality:
– All CPUs of the S7-1500 automation system support trace functionality. Trace
functionality supports you in troubleshooting and optimizing the user program,
especially for motion control or closed-loop control applications.
● Integrated system diagnostics:
– The alarms for the system diagnostics are automatically created by the system and
displayed on a PG/PC, HMI device, Web server or the integrated display. System
diagnostics information is also available when the CPU is in STOP mode.
● Integrated security:
– Know-how protection
The know-how protection protects user blocks against unauthorized access and
modifications.
– Copy protection
Copy protection links user blocks to the serial number of the SIMATIC memory card or
to the serial number of the CPU. User programs cannot run without the corresponding
SIMATIC memory card or CPU.
– Access protection
Extended access protection provides high-quality protection against unauthorized
configuration changes. You can use authorization levels to assign separate rights to
different user groups.
– Integrity protection
The system protects the data transferred to the CPU against manipulation. The CPU
detects erroneous or manipulated engineering data.
● The CPU 1515-2 PN supports the following additional functions:
– Firmware update
– PROFIenergy
– Shared device
– Configuration control
– Isochronous mode

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 13
Product overview
2.4 Operating and display elements

Reference
You will find additional information on the topic of "Integrated security/Access protection" in
the S7-1500/ET 200MP system manual
(http://support.automation.siemens.com/WW/view/en/59191792).

2.4 Operating and display elements

2.4.1 Front view of the module with closed front panel

The following figure shows the front view of the CPU 1515-2 PN.

① LEDs for the current operating mode and diagnostic status of the CPU
② Display
③ Operator control buttons

Figure 2-2 View of the CPU 1515-2 PN (with front panel) - front

Note
Temperature range for display
To increase the service life of the display, the display switches itself off when the permitted
operating temperature is exceeded. When the display cools down again, it automatically
switches itself on again. When the display is switched off, the LEDs continue to show the
status of the CPU.
For more information on the temperatures at which the display switches itself on and off,
refer to the Technical specifications (Page 31).

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

14 Manual, 12/2014, A5E32332431-AB
 Product overview
2.4 Operating and display elements

Pulling and plugging the front panel with display

You can pull and plug the front panel with display during operation.

WARNING
Personal injury and damage to property may occur
If you pull or plug the front panel of an S7-1500 automation system during operation,
personal injury or damage to property can occur in zone 2 hazardous areas.
Always disconnect the S7-1500 automation system from the power supply before you pull
or plug the front panel in zone 2 hazardous areas.

Locking the front panel

You can lock the front panel to protect your CPU against unauthorized access.
You can attach a security seal or a padlock with a diameter of 3 mm to the front panel.

Figure 2-3 Locking latch on the CPU

In addition to the mechanical lock, you can also block access to a password-protected CPU
on the display (local lock). You can find additional information on the display, configurable
protection levels and local locks in the S7-1500/ET 200MP
(http://support.automation.siemens.com/WW/view/en/59191792) system manual.

Reference
You will find detailed information on the individual display options, a training course and a
simulation of the available menu commands in the SIMATIC S7-1500 Display Simulator
(http://www.automation.siemens.com/salesmaterial-as/interactive-manuals/getting-
started_simatic-s7-1500/disp_tool/start_en.html).

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 15
Product overview
2.4 Operating and display elements

2.4.2 Front view of the module without front panel

The following figure shows the operator controls and connection elements of the
CPU 1515-2 PN.

① LEDs for the current operating mode and diagnostic status of the CPU
② Display connector
③ Slot for the SIMATIC memory card
④ Mode selector
⑤ LEDs for the 3 ports of the PROFINET interfaces X1 and X2
⑥ MAC addresses of the interfaces
⑦ PROFINET interface (X2) with 1 port
⑧ PROFINET IO interface (X1) with 2 ports
⑨ Connector for power supply
⑩ Fixing screws

Figure 2-4 View of the CPU 1515-2 PN (without front panel) - front

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

16 Manual, 12/2014, A5E32332431-AB
 Product overview
2.5 Mode selector switch

2.4.3 Rear view of the module

The following figure shows the connection elements on the rear of the CPU 1515-2 PN.

① Shield contact surfaces

② Backplane bus connector
③ Fixing screws

Figure 2-5 View of the CPU 1515-2 PN - rear

2.5 Mode selector switch

Use the mode switch to set the CPU operating mode.
The following table shows the position of the switch and the corresponding meaning.

Table 2- 1 Mode switch settings

Position Meaning Explanation

RUN RUN mode The CPU is executing the user program.
STOP STOP mode The user program is not being executed.
MRES Memory reset Position for CPU memory reset.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 17
Product overview
2.6 Functions

2.6 Functions

2.6.1 PROFINET IO
PROFINET is a fieldbus standard of the PROFIBUS user organization that defines a
cross-vendor communications and engineering model.
As part of PROFINET, PROFINET IO is a communication concept that is used to implement
modular, distributed applications. PROFINET IO IRT allows defined response times and
highly precise plant behavior.
A PROFINET IO system consists of the following PROFINET devices:
● IO controller
Device used to address the connected IO devices.
● IO device
A distributed field device that is assigned to an IO controller.
The PROFINET IO controller operating mode allows direct access to IO devices via
Industrial Ethernet.
The PROFINET IO device operating mode enables you to operate S7 stations or distributed
I/O systems with a CPU as "intelligent" IO devices on Industrial Ethernet.

General properties of PROFINET IO

PROFINET IO provides the following properties and functions:
● Real-time communication (RT)
● Isochronous real-time communication (IRT)
● Prioritized startup
● Media redundancy
● Device replacement without exchangeable medium
● I-device
● IO controller
● Shared device
● Isochronous mode

Reference
You can find additional information on the "PROFINET IO" topic in the STEP 7 online help
and in the PROFINET System Description
(http://support.automation.siemens.com/WW/view/en/19292127) manual.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

18 Manual, 12/2014, A5E32332431-AB
 Product overview
2.6 Functions

2.6.2 PROFIenergy

PROFIenergy
PROFIenergy is a PROFINET-based data interface for switching off consumers centrally and
in a coordinated manner during pause times regardless of the manufacturer or device type.
Through this, the process should only be provided with the energy that is absolutely
required. The majority of the energy is saved by the process; the PROFINET device itself
only contributes a few watts of savings potential.

Additional information
● PROFINET (http://support.automation.siemens.com/WW/view/en/68039307) function
manual
● You will find more information on PROFIenergy in the PROFINET specification on the
Internet (http://www.profibus.com).

2.6.3 Memory reset

Apart from a few exceptions, a "memory reset" involves clearing all internal memories and
then reading in the data on the SIMATIC memory card.

Options
You have the following options for resetting the memory of the CPU:
● Using the mode selector
● Using the display
● Using STEP 7

Procedure using the mode selector

To perform a memory reset of the CPU using the mode selector, follow these steps:
1. Set the mode selector to STOP.
Result: The RUN/STOP LED lights up yellow.
2. Set the mode selector to the MRES position. Hold the selector in this position until the
RUN/STOP LED lights up yellow for the 2nd time and remains lit (this takes three
seconds). After this, release the selector.
3. Within the next three seconds, return the mode selector to the MRES position, and then
back to STOP.
Result: The CPU performs a memory reset. During the memory reset, the RUN/STOP LED
flashes yellow. The RUN/STOP LED lights yellow when the CPU has completed the memory
reset.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 19
Product overview
2.6 Functions

Procedure using the display

To reach the desired menu command, "Memory reset", select the following sequence of
menu commands. Confirm with "OK" after each selection.
● Settings → Reset → Memory reset
Result: The CPU performs a memory reset.

Procedure using STEP 7

To perform a memory reset of the CPU via STEP 7, follow these steps:
1. Open the "Online Tools" task card of the CPU.
2. Click the "MRES" button in the "CPU control panel" pane.
3. Click "OK" to confirm the security prompt.
Result: The CPU is in STOP mode and performs a memory reset.

Response of the memory objects to the memory reset

The following table provides an overview of which memory objects are retained and which
are initialized when you reset memory.

Table 2- 2 Retentive characteristics of the memory objects

Memory object Contents

Actual values of the data blocks, instance data blocks Initialized
Bit memories, timers and counters Initialized
Retentive tags of technology objects (for example, calibration values of absolute encoders)* Retained
Diagnostics buffer entries (retentive area) Retained
Diagnostics buffer entries (non-retentive area) Initialized
IP address Retained
Counter readings of the operating hours counters Retained
Time Retained

* The retentive tags of technology objects are retained, but the contents of certain tags are partially re-initialized.

Reference
You will find more information about "Memory reset" in the Memory reset section in the
S7-1500, ET 200MP (http://support.automation.siemens.com/WW/view/en/59191792)
system manual.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

20 Manual, 12/2014, A5E32332431-AB
 Product overview
2.6 Functions

2.6.4 Restoring the factory settings of the CPU

The reset to factory settings function restores the CPU to the factory settings. The function
deletes all information that was stored internally on the CPU.

Note
If you want to remove a PROFINET CPU and use it elsewhere with a different program or
put it into storage, we recommend that you reset the CPU to its factory settings. Remember
that the Reset to factory settings function also deletes the IP address parameters.

Options
You have the following options for returning the CPU to the factory settings:
● Using the mode selector
● Using the display
● Using STEP 7

Procedure using the mode selector

Make sure that there is no SIMATIC memory card in the CPU and that the CPU is in STOP
mode (RUN/STOP LED lights up yellow).
Perform a reset to factory settings as follows:
1. Set the mode selector to STOP.
Intermediate result: The RUN/STOP LED lights up yellow.
2. Set the mode selector to the MRES position. Hold the mode selector in this position until
the RUN/STOP LED lights up yellow for the 2nd time and remains lit (this takes three
seconds). After this, release the selector.
3. Within the next three seconds, return the mode selector to the MRES position, and then
back to STOP.
Result: The CPU executes the reset to factory settings, during which time the RUN/STOP
LED flashes yellow. The RUN/STOP LED lit yellow indicates that the CPU has been reset to
the factory settings and is in STOP mode. The "Reset to factory setting" event is entered in
the diagnostics buffer.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 21
Product overview
2.6 Functions

Procedure using the display

Make sure that the CPU is in STOP mode (RUN/STOP LED lit yellow).
You can reach the "Factory settings" menu command by selecting the following menu
commands one after the other and confirming each selection with "OK".
● Settings → Reset → Factory settings
Result: The CPU executes a reset to factory settings, during which time the RUN/STOP LED
flashes yellow. The RUN/STOP LED lit yellow indicates that the CPU has been reset to the
factory settings and is in STOP mode. The "Reset to factory setting" event is entered in the
diagnostics buffer.

Procedure using STEP 7

Make sure that there is an online connection to the CPU that is to be reset to the factory
settings.
1. Open the Online and Diagnostics view of the CPU.
2. In the "Functions" folder, select the "Reset to factory settings" group.
3. Select the option button "Retain IP address" if you want to keep the IP address. Select
the option button "Delete IP address" if you want to delete the IP address.
4. Click "Reset".
5. Click "OK" to confirm the security prompt.
Result: The CPU is set to STOP mode and is reset to the factory settings.

Behavior of the memory objects with a reset to factory settings

The properties of the CPU are set to the following values:

Table 2- 3 Properties of the CPU objects in the factory settings

Memory object Contents

Actual values of the data blocks, instance data blocks Initialized
Bit memories, timers and counters Initialized
Certain retentive tags from technology objects Initialized
(for example, calibration values of absolute encoders)
Diagnostics buffer entries (retentive area) Initialized
Diagnostics buffer entries (non-retentive area) Initialized
IP address Depends on the procedure:
• Using mode selector: is deleted
• Using display: is deleted
• Using STEP 7: Depending on the setting of the "Retain IP
address"/"Delete IP address" option buttons
Counter readings of the operating hours counters Initialized
Time Initialized

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

22 Manual, 12/2014, A5E32332431-AB
 Product overview
2.6 Functions

Reference
You can find more information about the topic of "Reset to factory settings" in the function
manual Structure and Use of the CPU Memory
(http://support.automation.siemens.com/WW/view/en/59193101) as well as in the STEP 7
online help.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 23
Connecting up 3
This section provides information on the terminal assignment of the individual interfaces and
the block diagram of the CPU 1515-2 PN.

24 V DC supply voltage (X80)

The connector for the power supply is plugged in when the CPU ships from the factory.
The following table shows the terminal assignment for a 24 V DC power supply.

① +24 V DC of the supply voltage

② Ground of the supply voltage
③ Ground of the supply voltage for loop-through (current limited to 10 A)
④ +24 V DC of the supply voltage for loop-through (current limited to 10 A)
⑤ Spring opener (one spring opener per terminal)
Bridged internally:
① and ⑤
② and ③
Figure 3-1 Supply voltage connection

If the CPU is supplied by a system power supply, it is not necessary to connect the 24 V
supply.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

24 Manual, 12/2014, A5E32332431-AB
 Connecting up

PROFINET interface X1 with 2-port switch (X1 P1 R and X1 P2 R)

The following table shows the terminal assignment for the PROFINET interface with 2-port
switch. The assignment corresponds to the Ethernet standard for an RJ45 plug.

Table 3- 1 Terminal assignment of the PROFINET interface with 2-port switch

View Signal name Designation

1 TD Transmit data +
2 TD_N Transmit data -
3 RD Receive data +
4 GND Ground
5 GND Ground
6 RD_N Receive data -
7 GND Ground
8 GND Ground

PROFINET interface X2 with 1 port (X2 P1)

The pin assignments of the PROFINET interfaces X1 and X2 are identical.

Reference
You can find additional information on the topics of "Connecting the CPU" and
"Accessories/spare parts" in the S7-1500, ET 200MP
(http://support.automation.siemens.com/WW/view/en/59191792) system manual.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 25
Connecting up

Assignment of the MAC addresses

The CPU 1515-2 PN has two PROFINET interfaces, with the first interface having two ports.
The PROFINET interfaces each have a MAC address, and each of the PROFINET ports has
its own MAC address. The CPU 1515-2 PN therefore has five MAC addresses in total.
The MAC addresses of the PROFINET ports are needed for the LLDP protocol, for example
for the neighborhood discovery function.
The number range of the MAC addresses is sequential. The first and last MAC address are
lasered on the rating plate on the right side of each CPU 1515-2 PN.
The table below shows how the MAC addresses are assigned.

Table 3- 2 Assignment of the MAC addresses

Assignment Labeling
MAC address 1 PROFINET interface X1 • Front, lasered
(visible in STEP 7 for accessible devices) • Right side, lasered
(start of number range)
MAC address 2 Port X1 P1 R (required for LLDP, • Front and right side, not lasered
for example)
MAC address 3 Port X1 P2 R (required for LLDP, • Front and right side, not lasered
for example)
MAC address 4 PROFINET interface X2 • Front, lasered
(visible in STEP 7 for accessible devices) • Right side, not lasered
MAC address 5 Port X2 P1 (required for LLDP, for example) • Front, not lasered
• Right side, lasered
(end of number range)

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

26 Manual, 12/2014, A5E32332431-AB
 Connecting up

Block diagram
The following figure shows the block diagram of the CPU 1515-2 PN.

① Display PN X1 P1 R PROFINET interface X1 Port 1

② RUN/STOP/MRES mode selector PN X1 P2 R PROFINET interface X1 Port 2
③ Electronics PN X2 P1 PROFINET interface X2 Port 1
④ Switch L+ 24 V DC supply voltage
⑤ Backplane bus interface M Ground
⑥ Internal supply voltage R/S RUN/STOP LED (yellow/green)
X50 SIMATIC memory card ER ERROR LED (red)
X80 24 V DC Infeed of supply voltage MT MAINT LED (yellow)
X1 P1, LED Link TX/RX
X1 P2,
X2 P1
Figure 3-2 Block diagram of the CPU 1515-2 PN

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 27
Interrupts, error messages, diagnostics and system
alarms 4
The status and error displays of the CPU 1515-2 PN are described below.
You will find additional information on "Interrupts" in the STEP 7 online help.
You can find additional information on the topics of "Diagnostics" and "System alarms" in the
Diagnostics (http://support.automation.siemens.com/WW/view/en/59192926) function
manual.

4.1 Status and error display of the CPU

LED display
The figure below shows the CPU 1515-2 PN LEDs.

① RUN/STOP LED (yellow/green LED)

② ERROR LED (red LED)
③ MAINT LED (yellow LED)
④ LINK RX/TX LED for port X1 P1 (yellow/green LED)
⑤ LINK RX/TX LED for port X1 P2 (yellow/green LED)
⑥ LINK RX/TX LED for port X2 P1 (yellow/green LED)

Figure 4-1 LED display of the CPU 1515-2 PN (without front panel)

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

28 Manual, 12/2014, A5E32332431-AB
 Interrupts, error messages, diagnostics and system alarms
4.1 Status and error display of the CPU

Meaning of the LED displays

The CPU 1515-2 PN has three LEDs to signal the current operating status and diagnostics
status. The following table shows the meaning of the various combinations of colors for the
RUN/STOP, ERROR and MAINT LEDs.

Table 4- 1 Meaning of the LEDs

RUN/STOP LED ERROR LED MAINT LED Meaning

Missing or insufficient power supply on
LED off LED off LED off the CPU.
An error has occurred.
LED off LED flashes red LED off
CPU is in RUN mode.
LED lit green LED off LED off
A diagnostics event is pending.
LED lit green LED flashes red LED off
Maintenance demanded for the plant.
LED lit green LED off LED lit yellow The affected hardware must be
checked/replaced within a short period of
time.
Active Force job
PROFIenergy pause
Maintenance required for the plant.
LED lit green LED off LED flashes The affected hardware must be
yellow checked/replaced within a foreseeable
period of time.
Bad configuration
Firmware update successfully
LED lit yellow LED off completed.
LED flashes
yellow
CPU is in STOP mode.
LED lit yellow LED off LED off
The program on the SIMATIC memory
LED lit yellow card is causing an error.
LED flashes red LED flashes
yellow CPU defective
CPU is performing internal activities
LED off LED off during STOP, e.g. startup after STOP.
LED flashes yel-
low Download of the user program from the
SIMATIC memory card
Startup (transition from RUN → STOP)

LED flashes LED off LED off

yellow/green
Startup (CPU booting)
LED flashes LED flashes red LED flashes Test of LEDs during startup, inserting a
yellow/green yellow module.
LED flashing test

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 29
Interrupts, error messages, diagnostics and system alarms
4.1 Status and error display of the CPU

Meaning of the LEDs of the interfaces: X1 P1 R, X1 P2 R and X2 P1

Each port has a LINK RX/TX LED. The table below shows the various "LED scenarios" of
ports for the CPU 1515-2 PN.

Table 4- 2 Meaning of the LED

LINK TX/RX LED Meaning

There is no Ethernet connection between the PROFINET interface of the
LED off PROFINET device and the communication partner.
No data is currently being sent/received via the PROFINET interface.
There is no LINK connection.
The "LED flashing test" is being performed.
LED flashes green
There is an Ethernet connection between the PROFINET interface of your
LED lit green PROFINET device and a communication partner.
Data is currently being received from or sent to a communications partner
LED flickers yellow on Ethernet via the PROFINET interface of the PROFINET device.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

30 Manual, 12/2014, A5E32332431-AB
Technical specifications 5
6ES7515-2AM00-0AB0
Product type designation CPU 1515-2 PN
General information
Hardware product version FS02
Firmware version V1.7
Engineering with
STEP 7 TIA Portal can be configured/integrated V13 SP1
as of version
Display
Screen diagonal (cm) 6.1 cm
Operator controls
Number of buttons 6
Mode selector 1
Supply voltage
Type of supply voltage 24 V DC
Low limit of permitted range (DC) 19.2 V
High limit of permitted range (DC) 28.8 V
Reverse polarity protection Yes
Power and voltage failure backup
Power/voltage failure backup time 5 ms
Input current
Current consumption (rated value) 0.8 A
Inrush current, max. 2.4 A; rated value
I²t 0.02 A²s
Power
Power consumption from the backplane bus 6.2 W
(balanced)
Incoming power to the backplane bus 12 W
Power loss
Power loss, typ. 6.3 W
Memory
SIMATIC memory card required Yes
Work memory
Integrated (for program) 500 KB
Integrated (for data) 3 MB
Load memory
Plug-in (SIMATIC memory card), max. 32 GB
Buffering
maintenance-free Yes

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 31
Technical specifications

6ES7515-2AM00-0AB0
CPU processing time
For bit operations, typ. 30 ns
For word operations, typ. 36 ns
For fixed-point arithmetic, typ. 48 ns
For floating-point arithmetic, typ. 192 ns
CPU blocks
Number of elements (total) 6000; elements can be taken to mean blocks
such as DBs, FBs and FCs, as well as UDTs,
global constants etc.
DB
Number range 1 to 65535
Size, max. 3 MB; the maximum size of the DB is 64 KB with
non-optimized block access
FB
Number range 1 to 65535
Size, max. 500 KB
FC
Number range 1 to 65535
Size, max. 500 KB
OB
Size, max. 500 KB
Number of free-cycle OBs 100
Number of time-of-day interrupt OBs 20
Number of time-delay interrupt OBs 20
Number of cyclic interrupt OBs 20
Number of hardware interrupt OBs 50
Number of DPV1 interrupt OBs 3
Number of isochronous mode OBs 1
Number of technology synchronization interrupt 2
OBs
Number of restart OBs 100
Number of asynchronous error OBs 4
Number of synchronous error OBs 2
Number of diagnostic interrupt OBs 1
Nesting depth
Per priority class 24
Timers/counters and their retentivity
S7 counters
Quantity 2048
Retentivity
• Adjustable Yes

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

32 Manual, 12/2014, A5E32332431-AB
 Technical specifications

6ES7515-2AM00-0AB0
IEC counters
Quantity Unlimited (limited only by work memory)
Retentivity
• Adjustable Yes

S7 timers
Quantity 2048
Retentivity
• Adjustable Yes

IEC timers
Quantity Unlimited (limited only by work memory)
Retentivity
• Adjustable Yes

Data areas and their retentivity

Total retentive data area (including timers, 512 KB; in total; for bit memories, timers,
counters, bit memories), max. counters, DBs and technological data (axes),
usable retentive memory: 472 KB
Bit memory
Number, max. 16 KB
Number of clock memory bits 8; 8 clock memory bits, grouped in one clock
memory byte
Data blocks
Retentivity adjustable Yes
Retentivity preset No
Local data
Per priority class, max. 64 KB max. 16 KB per block
Address area
Number of I/O modules 8192; max. number of modules/submodules
I/O address area
Inputs 32 KB; all inputs are in the process image
Outputs 32 KB; all outputs are in the process image
Of which per integrated IO subsystem
• Inputs (volume) 8 KB

• Outputs (volume) 8 KB

Of which per CM/CP

• Inputs (volume) 8 KB

• Outputs (volume) 8 KB

Process image partitions

Number of process image partitions, max. 32

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 33
Technical specifications

6ES7515-2AM00-0AB0
Hardware configuration
Number of hierarchical IO systems 20
Number of DP masters
Via CM 8; a maximum of 8 CMs/CPs (PROFIBUS,
PROFINET, Ethernet) can be inserted in total
Number of IO controllers
Integrated 1
Via CM 8; a maximum of 8 CMs/CPs (PROFIBUS,
PROFINET, Ethernet) can be inserted in total
Rack
Modules per rack, max. 32; CPU + 31 modules
Rack, number of rows, max. 1
PtP CM
Number of PtP CMs The number of PtP CMs you can connect is only
limited by the available slots
Time
Clock
Type Hardware clock
Deviation per day, max. 10 s; typ.: 2 s
Buffered period 6 wk; at 40 °C ambient temperature, typ.
Operating hours counter
Quantity 16
Time-of-day synchronization
Supported Yes
in AS, Master Yes
in AS, Slave Yes
On Ethernet via NTP Yes
Interfaces
Number of PROFINET interfaces 2
1. Interface
Interface hardware
• Number of ports 2

• Integrated switch Yes

• RJ-45 (Ethernet) Yes; X1

Protocols
• PROFINET IO controller Yes

• PROFINET IO device Yes

• SIMATIC communication Yes

• Open IE communication Yes

• Web server Yes

• Media redundancy Yes

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

34 Manual, 12/2014, A5E32332431-AB
 Technical specifications

6ES7515-2AM00-0AB0
2. Interface
Interface hardware
• Number of ports 1

• Integrated switch No

• RJ-45 (Ethernet) Yes; X2

Protocols
• PROFINET IO controller No

• PROFINET IO device No

• SIMATIC communication Yes

• Open IE communication Yes

• Web server Yes

Interface hardware
RJ-45 (Ethernet)
100 Mbps Yes
Autonegotiation Yes
Autocrossing Yes
Industrial Ethernet status LED Yes
Protocols
Number of connections
Number of connections, max. 192; via integrated interfaces of the CPU and
connected CPs/CMs
Number of connections reserved for ES/HMI/Web 10
Number of connections via integrated interfaces 108
Number of S7 routing connections 16
PROFINET IO controller
Services
• PG/OP communication Yes

• S7 routing Yes

• Isochronous mode Yes

• Open IE communication Yes

• IRT Yes

• MRP Yes; as MRP redundancy manager and/or MRP

client; max. number of devices in the ring: 50
• PROFIenergy Yes

• Prioritized startup Yes; max. 32 PROFINET devices

• Number of connectable I/O devices, max. 256; a maximum of 512 distributed I/O devices
can be connected by means of PROFIBUS or
PROFINET.
• Of which IO devices with IRT and the "high 64
performance" option, max.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 35
Technical specifications

6ES7515-2AM00-0AB0
• Number of IO devices that you can connect for 256
RT, max.

• Of which are in line, max. 256

• Number of IO devices that can be activated/ 8

deactivated simultaneously, max.

• Number of IO devices per tool changer, max. 8

• Update times The minimum value of the update time also

depends on the communication component set
for PROFINET IO, on the number of IO devices,
and on the quantity of configured user data.
With RT
• for send clock of 250 µs 250 μs to 128 ms

• for send clock of 500 µs 500 μs to 256 ms

• for send clock of 1 ms 1 ms to 512 ms

• for send clock of 2 ms 2 ms to 512 ms

• for send clock of 4 ms 4 ms to 512 ms

With IRT and the "high performance" option

• for send clock of 250 µs 250 μs to 4 ms

• for send clock of 500 µs 500 μs to 8 ms

• for send clock of 1 ms 1 ms to 16 ms

• for send clock of 2 ms 2 ms to 32 ms

• for send clock of 4 ms 4 ms to 64 ms

• For IRT with the "high performance" option and Update time = set "odd-numbered" send clock
parameter assignment for so-called (any multiple of 125 µs: 375 µs, 625 µs ...
"odd-numbered" send clocks 3 875 µs)

PROFINET IO device
Services
• PG/OP communication Yes

• S7 routing Yes

• Isochronous mode No

• Open IE communication Yes

• IRT, supported Yes

• MRP, supported Yes

• PROFIenergy Yes

• Shared device Yes

• Number of IO controllers with Shared Device, 4

max.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

36 Manual, 12/2014, A5E32332431-AB
 Technical specifications

6ES7515-2AM00-0AB0
SIMATIC communication
S7 communication, as server Yes
S7 communication, as client Yes
User data per job, max. See online help (S7 communication, user data
size)
Open IE communication
TCP/IP Yes
• Data length, max. 64 KB

• Several passive connections per port, Yes

supported
ISO-on-TCP (RFC1006) Yes
• Data length, max. 64 KB
UDP Yes
• Data length, max. 1472 bytes

DHCP No
SNMP Yes
DCP Yes
LLDP Yes
Web server
HTTP Yes; standard and user-defined pages
HTTPS Yes; standard and user-defined pages
Further protocols
MODBUS Yes; MODBUS TCP
Media redundancy
Changeover time on line interruption, typ. 200 ms
Number of ring nodes, max. 50
Isochronous mode
Isochronous mode (application synchronized up to Yes; with minimum OB 6x cycle of 500 µs
terminal)
Constant bus cycle time Yes
S7 signaling functions
Number of stations that can be logged in for sig- 32
naling functions, max.
Block-related alarms Yes
Number of configurable interrupts, max. 10000
Number of simultaneously active interrupts in
interrupt pool
• Number of reserved user interrupts 600

• Number of reserved interrupts for system 200

diagnostics

• Number of reserved interrupts for motion 160

technology objects

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 37
Technical specifications

6ES7515-2AM00-0AB0
Test/commissioning functions
Joint commissioning (Team Engineering) Yes; parallel online access possible for up to
8 engineering systems
Status block Yes; up to 8 simultaneously (in total from all
ES clients)
Single-step No
Status/modify
Status/modify tag Yes
Tags Inputs, outputs, bit memories, DBs, timers,
counters
Of which are status tags, max. 200; per job
Of which are modify tags, max. 200; per job
Force
Forcing, tags Inputs, outputs
Number of tags, max. 200
Diagnostics buffer
Available Yes
No. of entries, max. 3200
• Of which are power failure-proof 500

Traces
Number of configurable traces 4; up to 512 KB data possible per trace
Interrupts/diagnostics/status information
Diagnostic indicator LED
RUN/STOP LED Yes
ERROR LED Yes
MAINT LED Yes
Connection display LINK TX/RX Yes
Supported technology objects
Motion Yes
• Speed-controlled axis
– Number of speed-controlled axes, max. 30; Requirement: no other motion technology
objects have been created
• Positioning axis
– Number of positioning axes, max. 30; Requirement: no other motion technology
objects have been created
• Synchronous axes (relative gearing)
– Number of axes, max. 15; Requirement: no other motion technology
objects have been created
• External encoder
– Number of external encoders, max. 30; Requirement: no other motion technology
objects have been created

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

38 Manual, 12/2014, A5E32332431-AB
 Technical specifications

6ES7515-2AM00-0AB0
Controller
• PID_Compact Yes; universal PID controller with integrated
optimization
• PID_3Step Yes; PID controller with integrated optimization
for valves
• PID temp Yes; PID controller with integrated optimization
for temperature
Counting and measuring
• High-speed counter Yes

Ambient conditions
Ambient temperature in operation
Horizontal installation, min. 0 °C
Horizontal installation, max. 60 ℃; display: 50 ℃, the display is switched off at
an operating temperature of typically 50 ℃
Vertical installation, min. 0 °C
Vertical installation, max. 40 ℃; display: 40 ℃, the display is switched off at
an operating temperature of typically 40 ℃
Configuring
Programming
Programming language
• LAD Yes

• FBD Yes

• STL Yes

• SCL Yes

• GRAPH Yes

Know-how protection
User program protection Yes
Copy protection Yes
Block protection Yes
Access protection
Password for display Yes
Protection level: Write protection Yes
Protection level: Read/write protection Yes
Protection level: Complete protection Yes
Cycle-time monitoring
Low limit Adjustable minimum cycle time
High limit Adjustable maximum cycle time
Dimensions
Width 70 mm
Height 147 mm
Depth 129 mm
Weights
Weight, approx. 830 g

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 39
Technical specifications

General technical specifications

You can find information on the general technical specifications, such as standards and
approvals, electromagnetic compatibility, protection class, etc., in the S7-1500, ET 200MP
(http://support.automation.siemens.com/WW/view/en/59191792) system manual.

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

40 Manual, 12/2014, A5E32332431-AB
Dimensional drawing A
This section contains the dimensional drawing of the module on the mounting rail, as well as
a dimensional drawing with the front panel open. Keep to the dimensions when installing in
cabinets, control rooms, etc.

Dimensional drawings for CPU 1515-2 PN

Figure A-1 Dimensional drawing of CPU 1515-2 PN, front and side views

Figure A-2 Dimensional drawing CPU 1515-2 PN, side view with open front panel

CPU 1515-2 PN (6ES7515-2AM00-0AB0)

Manual, 12/2014, A5E32332431-AB 41