TC 1475

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

COLOR TELEVISION

SERVICE MANUAL

TC1475
CONTENTS

A. Brief Introduction

B. ELECTRICAL SPECIFICATIONS

C. Structure Block Diagram

D. Definition & Function of TMPA8873-XXXX Pins

E. Remote control(key assignments list)

F. Circuit Analysis Main ICs Introduction

G. Descriptions for the operation of factory mode


A. Brief Introduction

2
TMPA8873-XXXX is introduced in this chassis, controlled by I C
bus, implement FS PLL tuning.
1、FS tuning 45.75M. band adjustable
2、tuning in USA channel table by CATV/antenna.
3、Auto tuning, frequency fine tuning, skip setting
4、Color Sys: PAL-M\ PAL-N\ NTSC-M auto identified
5、2 AV input, YUV input, AV1\AV2\DVD(YUV) input preset
6、Switch program by numeric key directly,
7、Picture mode: personal\dynamic\standard\soft, switched by one
key
8、Picture parameters adjustment: brightness\contrast\color\
sharpness\hue
9、Mute control: mute when switch programs and AV
10、Power on/off timer, program timer
11、Auto power off 15 minutes later when no signal in TV mode
12、special halftone menu display
13、English\French\Spanish\Portuguese menu display
14、8 self-detect signals generated by CPU for geometry distortion
adjustment
15、50HZ/60HZ auto identified
16、Child lock(by press DISP button 4 seconds)
17、AV stereo, 2 volume inner control
18、Color and vertical position of main menu variable
19、Factory logo setting when no signal
20、TA1304/TA1343 tone control
22、Multifunctional RC unit(LA7461、TA9028、SC6122)may be efficiency or only one

be efficiency
B. ELECTRICAL SPECIFICATIONS

Model Number
RF system PAL-M/N 、NTSC-M
Video system PAL-M/N 、NTSC-M
Receiving AIR
channel
CATV(STD)
CATV(HRC)
CATV(IRC)
Channels preset 181
Antenna input 75 Ohm Coaxial Cable
Picture tube 37cm~(14”~) diagonal
Audio output 14” : Maximum 2.5W×2

Power source AC90V~260V 50/60Hz


Weight(Approx) 14”(11Kg)
Dimensions 14” 450(W)×410(D)×378(H)mm
(W×H×D) (Approx)

Power Consumption 14”=65W

Designs and specifications are subject to change without notice.

WARNING
The chassis in this receiver is partially hot. Use an isolation

transformer between the line cord plug and power receptacle, when

servicing this chassis. To prevent electric shock, do not remove cover.

No user-serviceable parts inside. Refer servicing to qualified service

personnel.
C. Structure Block Diagram

Tuner
TU201

SAWF
SIF BTSC
AN5832 or
4053
LA72700

TC4053 AV1
AV SW AV2

TDA1030
TA1304/TA1343
AN7522/AN17821

TDA1030
A1 A2

S-AV y
Vout LA78040/TDA9302
Video Audio LA78041/TDA8177

S Y Cb Cr CRT

FBT
T471
2 in Chip
Hout

TMPA8873-XXXX
EEPROM
8K bit

TA9028-023/022
KEY LA7461
MATRIX RECEIVEERMP SC6122
TMPA8873-XXXX Block Diagram:
D. Definition & function of TMPA 8873-XXXX Pins:
TMPA8873-XXXX:
① CPU part:
item definition description
1 DVD high level output in DVD mode
2 NO USE
3 KEY Control signal input; general
keyboard circuit auto identified
4 GND MCU GND
5 REST MCU reset when power on
6 X-TAC
Connect ports for crystal; 20PPM precision required
7 X-TAC
8 TEST For MCU experimentation, connected to GND normal
9 5V Power input for CCD amplitude restricted circuit
10 Vss GND for CCD amplitude restricted circuit
54 GND GND for surge circuit
55 5V Power for surge circuit;
Duty cycle and Ripple voltage less than 10 mV;
56 AV SW Multi-control level output 2 or 3 TV/AV mode
57 SDA SDA input
58 SOL SCL input
59 50/60HZ Low level when 50HZ
High level when 60HZ
60 NO USE
61 MUTE MUTE control
62 NO USE
63 RMT IN
RC unit signal input
Power control; low level for initialization; related with
64 Power
item ONTIME of Page F11

Note for control port output state: (in the output table below,”0”for low level, “1” for high
level)

Pin3 Description:
Voltage range for each button (middle value is suggested)
KEY Off P+ P- V+ V- MENU TV/AV POWER
Range(
0V ≤1.16V ≤1.74V ≤2.45V ≤3.17V ≤3.88V ≤4.60V ≤5V

Range 0≤
5V ≤1.02V ≤1.74V ≤2.45V ≤3.17V ≤3.88V ≤4.60V
( 0.45V
Pin6、Pin7 less than 20PPM precision required for crystal
Duty cycle and Ripple voltage of power for Pin55 must less than 10 mV;
(power for OSD clock)

Pin56 AV/TV switch


TV AV1/S/DVD AV2 Connect way
OPT.2=0 0V 0V 5V Pull up resistance
connected to 5V or 8V

10K pull up
resistance connected
OPT.2=1;OPT.5=0 0V 2.5V 5V
to 5V and 10K pull
down resistance
connected to GND

10K pull up
resistance
OPT.2=1;OPT.5=1 0V 5V 2.5V connected to 5V
and 10K pull down
resistance
connected to GND

Pin59 50HZ/60HZ switch


Pin59 NTSC(60HZ) PAL(50HZ)
voltage 5V 0V

Pin61 Mute 1K pull up resistance


Pin64 Power
a) RC, Pin61\64 wave: Power on
power off

Power

Mute

Power off

Cold
Switch
power on
program
Mute
Mute setting
0 Not mute in no signal TV mode
when no blue background,
MODE2.0
1 Mute in no signal TV mode
when no blue background
0 Mute in no signal AV mode
when no blue background
MODE2.1
1 Not mute in no signal AV mode
when no blue background

② Signal transacting part:


11 TV GND Analog GND
12 FBP-IN Input port for flyback pulse
13 H-out Output port for horizontal driver pulse
Connect port for horizontal AFC filter
14 H-AFC
The voltage of this port control the frequency of H-VCO
Connect capacitor for SAW generating,
15 V-SAW The amplitude of SAW is a constant because of the
controlling of V-AGC
16 V-out Vertical driver pulse output
17 H-Vcc 8V power for deflection
18 TV GND Analog GND
19 Cb Input port for Cb signal
20 Y-IN Input port for Y signal
21 Cr Input port for Cr signal
22 EXT-AU1 AUDEO1 input
23 C-in Input port for C signal
24 V2 Input port for CVBS/Y signal
25 ACL Interface for ACL filter
26 TV-in Input port for TV video signal
27 ABC-in ABCL input
28 Audio-out1 Port 1 for audio output with volume control function
29 Audio-out2 Port 2 for audio output with volume control function
30 TV-out PIF demodulation signal(full TV signal) output
31 SIF Sound intermediate frequency output(may no periphery
circuit)
32 EXT-AU2 AUDEO2 input
33 SIF in Second sound intermediate frequency or horizontal
phase emendation signal input
34 DC NF Connect with capacitor
35 PIF•PLL Connect with PIF-PLL filter
36 IF-5V 5V power for IF
37 S-Reg Connected with filter capacitor, stabilization inner bias
38 AU OUT Audio output, not with volume control
39 IF AGC Connected with AGC filter
40 IF GND IF GND
41 IF in Pin41、Pin42 are input port for differential amplifier,
42 IF in input IF signal from SAW
43 RF AGC RF-AGC signal output for tuner
44 Black Det Connected with black detect filter
45 Monitor out CVBS/SVM output, CVBS/SVM selected by I²C
46 APC fil Connected with APC filter of chroma decode circuit
47 YC VCC5V1 Power for YC
48 SYNC OUT SYNC output
49 DVCC—3.3V Power for digital circuit
50 R out R output
51 G out G output
52 B out B output
53 GND Connected with analog GND

P.P Picture mode key 00001110 0E 0E 0x19 0x13


TV/AV TV/AV key 00001111 0F 0F 0x0B 0x0f
P- Channel lessen key 00010000 10 10 0x17 0x1a
P+ Channel add key 00010001 11 11 0x13 0x1b
Vol- Volume lessen key 00010010 12 12 0x14 0x1e
Vol+ Volume add kye 00010011 13 13 0x10 0x1f
MUTE Mute key 00010100 14 14 0x16 0x15
SLEEP Sleep key 00010101 15 15 0x0f 0x19
DISP/LOCK Display/lock key 00010110 16 16 0x1b 0x14
RECALL RECALL key 00010111 17 17 0x1a 0x0e
MENU Menu key 00011100 1C 1C 0x0e 0x10
PIC Picture menu key 0001101 1D 1D 0x1c 0x0c
SOUND-MODE SOUND-MODE key 00011110 1E 1E 0x1d 0b
D-MODE Factory key 00101100 2C 2C 0x11 0x1d

F. Circuit Analysis
1. tuning circuit:

Buildup by frequency synthesized, PLL tuning, controlled by I2C bus tuner and some

individual components. Tuning process controlled by correlation pins of UOC

TMPA8873-XXXX. Pin57 & pin58 of CPU output I2C tuning data for SCL & SDA of tuner.

FS tuner introduced in this chassis, cooperate with SCL & SDA data from pin57 &

pin58 of N101, processing FS auto tuning. 33V for tuner supplied by 110V(130V), divided

by R518 and stabilized voltage by N505.

Frequency synthesized fashion is also called PLL frequency synthesized fashion. It is

the CPU controlled by channel subscribe program、band switch and data from RC receiver

and give the band switch signal. CPU set frequency divide ratio for variable frequency

divider of PLL. Variable frequency divider dividing the local oscillation frequency from tuner

and compare the phase with benchmark frequency, adjust local oscillation frequency accord

with the local oscillation frequency needed by each channel.

2、Picture IF circuit:

The IF signal from tuner enter into SAW filter Z101(F45C) after amplified by

Pre-Amp built up by V103 and so forth, filtered accordance with IF characteristic and enter

into pin41 & pin42 of N101(N103) at last. The purpose of add Pre-Amp is to compensate the

inset loss of SAW filter and advance SNR.

The IF signal be amplified and video frequency demodulated after enter


TMPA8873-XXXX and output PIF demodulation signal(CVBS) from pin30, pass through the

emitter follower buildup by R155、R156、V104、R158, coupled to pin26 (inner switch)of

TMPA8873-XXXX by C147.
3、sound processing:

The SIF2, come from inner phase lock demodulate of TMPA8873-XXXX, turned

into audio signal after limiting amplifier and frequency discriminator. Two

audio signal, out of pin28 & pin29 of TMPA8873-XXXX, enter pin9 of N681 & N691

separated and audio power amplified. They are used to driver speakers separated

after output from pin16 of N681 & N691.

4、periphery AV input processing:

Periphery AV1(V1、L1、R1)input from pin5、pin 12、pin 2 of N801(TC4053)

separated. Periphery AV2(V2、L2、R2)input from pin3、pin 13、pin1 of N801(TC4053)

separated. The level output from pin56 of N103 control the switch of N801. The video

signal, output from pin4 of N801, transmitted to inner of TMPA8873-XXXX by pin24 of N103

after switched. The audio signal, output from pin14 & pin15 of N801, transmitted

to inner of TMPA8873-XXXX by pin24 of N103.

5、line scan:

Inner synchronize separate included in TMPA8873-XXXX, build up by VCO surge circuit,

line frequency divider, AFC circuit, line output driver. Line driver signal output from pin13

of TMPA8873-XXX, amplified by V431 (2SC2383) at line-excited level and then

amplified by V432 at line output level.

T471 is the FBT. Volts d.c. +110V(21”)+135V(29”)enter it through pin4. Line flyback

pulse divided into two routes: one for heater (virtual value 6.3V) and one for FBP of AFC

after through R405 and stabilized voltage by VD408 (9.1V). Pulse output from pin10 of T471

rectified by VD447 and filter by C447 and we get +180V for Pre-Amp as power supply. Pin9

of FBT is ABL , used as input of pin27 of TMPA8873-XXXX.

6、field scan:

Field output level buildup by CD78040/LA78041(N451) and its periphery components.

Field synchronization signal enter into saw wave produce circuit after synchronization

separate. Pin16 of TMPA8873-XXXX output field saw wave driver signal to pin1 of
CD78040/LA78041by pass R451, and it is output from pin5 after driver amplified and output

power amplified at the inner of CD78040/LA78041(N451). C450、R454、R453、R461A/B are

field feedback components for improving filed linearity and stabilizing the field work point.

Field feedback signal enter pin7 of LA7841. VD451、C451 buildup a bootstrap rise voltage

circuit. The power supply for pin6 of LA7841 is 26V during scan time and bootstrap rise

voltage to 48V during flyback time. In this way, the work efficiency of field output level is

improved and also the voltage of power supply for pin7 will not less than the pulse amplitude

of pin5 during flyback, and eliminate retrace efficiency accordingly. By the way, if the

linearity of scan is not well, it is something wrong with bootstrap rise voltage circuit

commonly.

7、 H-PARAB emendation circuit:

The principle of H-PARAB emendation is to using field parabolical wave to modulating

amplitude of horizontal scan current. The current accretion according to parabolical wave

rule during electron beam scan the middle of screen and so on the H-PARAB raster turned

into rectangle raster.

8、 color driver:

Tricolor signal amplified by tricolor driver. The white balance adjustment of this chassis

completed under the control of I2C bus.

9、power supply:

1、A3 power supply: The power supply of this chassis adopt self-excitation pulse

transformer coupling switch power. It’s very steady because of the photo-electricity transfer

component adopted for stabilized voltage sampling.

1) power supply analyses:

A、Rectifying:

A.C. 220V is delivered to bridge rectifier circuit buildup by VD503~VD506 after filted

by noise filter composed by L501、R501、C501、C502, and transformed to 300V D.D. voltage

after filted by L502、C507 and powered supply for collector of V513 by elementary coil of

switch mode transformer T511.

B、oscillator circuit:

Self-excitation oscillator circuit buildup by switch transistor V513 and switch-mode


transformer T511, and the error sampling circuit buildup by R552~R554、RP551、VD560、

V533、N501.

C、stabilized voltage:

Photo coupler N501 buildup by a LED and a photo trail-transistor. The work state of photo

trail-transistor controlled by the light emitted by LED. The voltage controlling LED get from

110V/130V by sampling circuit buildup by R552~R554、RP551、VD560、V553. The voltage

from collector of V553, connected with the LED negative inner N501,controlling the light

emitted by LED.

D、Rectifier and Filter Circuit:

Switch-mode transformer T511 supply different working voltage for chassis by its 4

secondary windings and separate the power supply of chassis from mains supply..

2、WIDE POWER(90V~260V)IC-W65XX Introduction:


A、W65XX Block diagram(Connection diagram):
B、Functions of Each Terminal:

Terminal
Symbols Descriptions Functions
No.
1 D Drain terminal Mosfet Drain

2 — — —

3 S/GND Source and Ground terminal MOSFET Source and Ground

4 Vcc Power supply terminal Input of power supply for control circuit
Soft-Start and Over-current Adjustment of over-current protection
5 SS/ADJ
protection adjustment Terminal and Soft Start Operation Time set up
Constant Voltage Control Signal Input
6 FB Feed back terminal and Burst(intermittent)mode Oscillation
Control
Bottom Detection Signal Input and
7 BD Bottom Detection Terminal
External Latch Signal Input

The T08 chassis mainly use the following IC and assemblies


1、14~21”(AC90~260V)
NO. Position Type Function Description
1 N103 8873CPBNGXXX Controller and small signal processor
2 N102 ATME24C08 EEPROM
3 N801 HM14053N Analog swtich
4 N451 CD78040/LA78040 Vertical scan output stage circuit
5 N681、N691 TDA1030 Audio processor
6 N502 STR-W6553A Power supply circuit
7 TU201 ET-5C511-M04 Tuner

2、25~34”(AC90~260V)
NO. Position Type Function Description
1 N101 8873CPBNGXXX Controller and small signal processor
2 N102 ATME24C08 EEPROM
3 N801 HM14053N Analog swtich
4 N451 LA78041/TDA8177 Vertical scan output stage circuit
5 N701 AN7522/AN17821 Audio Amplifier
6 N502 STR-W6556A Power supply circuit
7 TU201 ET-5C511-M04 Tuner
8 N601 TDA1343/TDA1304 Audio Processor
G. Descriptions for the operation of factory mode:
1、How to enter the factory mode:
A、Use remote control:

Press panel Volume down (V-) key of the TV set to lower the volume to 0(don't
release it) while pressing the display key of the remote unit to enter debug menu of
factory mode 。

B、Use factory remote control:

Press“FAC”key, goes to the debug menu of factory mode directly

2)How to exit from factory mode

A、Use remote control:

1)Press ”DISP” key, then TV system will exit from the factory debug menu status to

normal status

2)Switch off the power supply and power on, then TV system will exit from the

factory mode and goes to normal status

B、Use factory remote control:

Press FAC” key, then TV system will exit from the factory debug menu status to the

factory aging mode, Press “FAC” key again, system will go to normal status.

2、Direct key function descriptions for factory mode ,


In factory mode, some keys function will be changed to factory function key for debugging.
1) Mute Key: Page Up for factory mode menu
Return Key: Page Down for factory mode menu
“CH+、CH-” Key: Select the item of menu
“VOL+、VOL-” Key: Modify the data
2) Press “-/--” Key,V Stop function will implement and shows a horizontal line for the
white balance adjustment.
“1” Key R-CUT increase
“4” Key R-CUT decrease
“2” Key G-CUT increase
“5” Key G-CUT decrease
“3” Key B-CUT increase
“6” Key B-CUT decrease

4)Press“DISP”key, 4 kind of test signal will be displayed on the screen.


3、 Items on page F0~F5:
F 0:NTSC Geometr adjust(not for PAL)
Items Description Recommend Data Max
NT.H.PHASE Horizontal Phase for 60Hz system 19 31
NT.V.POSI Vertical Phase for 60Hz system 01 15
NT.V.SISE Vertical Amplitude for 60Hz system 28 63
NT.V.LIN Vertical Linearity for 60Hz system 15 31
NT.V.SC V-S correction for 60Hz system 15 31
NT.HBOW H Bow correct for 60Hz system 04 07
NT.HPARA Parallelogram correct for 60Hz system 04 07
H.BLK.LEFT Horizontal Left vanish 0 07
H.BLK.RIGHT Horizontal Right vanish 0 07

F 1:PAL Geometr adjust(offset refer to NTSC)only for PAL signal


Items Description Recommend Data Max
H.PHASE Horizontal Phase for 50Hz system 0 -11~10
V.POSITION Vertical Phase for 50Hz system 0 -11~10
V.SIZE Vertical Amplitude for 50Hz system 0 -11~10
V.LIN Vertical Linearity for 50Hz system 0 -11~10
V.SC V-S correction for 50Hz system 0 -11~10
HBOW H Bow correct for 50Hz system 4 -8~07
HPARA Parallelogram correct for 50Hz system 4 -8~07

F 2:Broghtness balance adjust


Items Description Recommend Data Max
RC Red cut 32 255
GC Green cut 32 255
BC Blue cut 32 255
GD Green driver 60 127
Blue driver 72 127
SB Sub Brightness 00 63

F3:Sub-Contrast 、Sub-Color and OSD adjustment


Items Description Recommend Data Max
SUB.CONT Sub-contrast 12 15
SUB.COLOR Sub-color 10 127
ST3 TV NTSC3.58 high frequency advance degree 37 63
SV3 AV NTSC3.58 high frequency advance degree 37 63
ST4 TV PAL4.43 high frequency advance degree 37 63
SV4 Other AV system high frequency advance
37 63
degree
SVD DVD high frequency advance degree 37 63
OSD.CONT OSD contrast 1 15
OSD.H.POSI OSD horizontal position 16 127
OSD.V.POSI OSD vertical position 32 127

F4: Language adjustment


Items Description Recommend Data Max
ENGLISH ENGLISH 01 01
FRENCH FRENCH 01 01
SPANISH SPANISH 01 01
PORTUGUESE PORTUGUESE 00 01

F5:AGC、Tuner BAND adjustment


Items Description Recommend Data Max
RF.AGC Automatic gain control 35 63
MENU1 Color option for tool bar of menu 13 15
MENU2 Translucence color option of mene 8 15
VHL VHL BAND 39 79
UHF UHF BAND 127 127
POWER 0:Standby;1:open;2:menory 2 2
PAGE Sub –menu of factory mode 00 01
PART LIST

Description Specification

REGULADOR FUENTE STR W6553A


OPTOACOPLADOR B0838 / 817B
IC TLC431AC Regulador
REGULADOR 5V
REGULADOR 9V
TERMISTOR MF72 / 7D 13
Converter Transformer BCK35-70117
IC Control/Jungle 64Pin N103: TOSHIBA / 8873CSCNG6UP3
MEMORY N102: 24C08
VERTICAL OUT N451: D78040
AUDIO OUT N701: AN17821A
AV SWICHT N801: HCF 4053BE
TUNNER ET-5C511-M04
HDT transformer JPE UU10.5
BSC24-01N40
FLY-BACK Transformer BSC24-01N4004A
Transistor driver horiz. 2SC2383
HORIZONTAL OUT D1555
Transistor driver RGB 2SC2482
Condensador Fuente 150uf/400V
Resistencia Potencia 8.2 / 5W
Control Remoto 6UP3-912

You might also like