Assignment- 35

SECTION-I
Single Correct Answer Type 5 Q. [3 M (–1)]

1. A rod of mass M & length  stands along z-axis. Its lower end is hinged at the centre of a disc of
same mass M and radius R. The whole arrangement is rotating freely about z-axis with an angular
velocity 0. The rod falls on disc & rotates with disc. Find the angular speed of the arrangement.
0R2 30R2 60R2 60R
(A) (B) (C) (D)
2 2 2 2 2
+R 2 2
+ 3R 2
+ 6R + 6R2

2. A small disk is attached to the end of a light inextensible string, which passes through a hole in a
frictionless horizontal tabletop. Initially the disk moves on a circle of radius R with kinetic energy
K0. The string is then slowly pulled so that the disk finally rotates on a circle of radius R/. What
is the work W done in pulling the string ?

(A) W = 2K0 (B) W = (2 – 1)K0 (3) W = ( – 1)K0 (4) W = 0

3. Particle of mass 1 kg moves along the curve y = x2. Magnitude of angular momentum of particle
1
about origin when particle has x co-ordinate as m and x component of velocity as 4 m/s is :
2
(A) 4 J – S (B) 3 J – S (C) 2 J – S (D) 1 J – S

4. A sphere is rolling on the rough surface without any slipping at the contact point. Find the radius
R
of curvature of the trajectory of the point A when it is at distance vertically above the center of
2
sphere (as shown in figure).

9 R 3R
(A) R (B) (C) (D) R
2 2 2
Space for Rough Work

Assignment 1
5. A disc of radius R rolls on a horizontal surface with linear velocity V and angular velocity . There
is a point P on circumference of disc at angle  with upward vertical diameter measured
anticlockwise (see figure), which has a vertical velocity. Here  is equal to :

V  V V V
(A)  + sin–1 (B) − sin−1 (C)  − cos−1 (D)  + cos−1
R 2 R R R

SECTION-II
Multiple Correct Answer Type 4 Q. [4 M (–1)]

6. You give a push on three identical free sticks at the locations shown below. Your force F is constant
& it acts over the same small distance x in each case.

(A) Velocity of centre of mass is largest in case-(c)

(B) Angular velocity of rod is largest in case-(a)
(C) Work done by force F is same in all the cases
(D) Rotational kinetic energy is same in all the cases

7. A rod is connected with the (rigid body) disc at centre of disc at point ‘P’. The disc can freely rotate
about point P where it is hinged with rod. rod can rotate freely about fixed hinge Q. Now whole
arrangement is released from horizontal position as shown in the diagram.

(A) Initial angular acceleration of (rigid body) disc is zero.

9g
(B) Initial angular acceleration of (rigid body) disc is .
8
(C) Angular speed of (rigid body) disc when rod becomes vertical is zero.
3 g
(D) Angular speed of (rigid body) disc when rod becomes vertical is rad/s.
2

Space for Rough Work

Assignment 2
8. A ring of mass M and radius R rotates in a vertical plane about an axle at the edge of the ring. The
ring starts at its highest position and is given a very small push to start it rotating. At its lowest
position,
(A) The angular acceleration is zero
g
(B) The angular velocity is
R
(C) The force exerted by the axle on the ring is vertical
(D) The force exerted by the axle on the ring is 3Mg.

9. A uniform rod of mass M = 2kg and length L is suspended by two smooth hinges 1 and 2 as shown
L
in the figure. A force F = 4N is applied downward at a distance from the hinge 2. Due to the
4
application of force F, the hinge 2 breaks. At this instant, applied force F is also removed. The rod
starts to rotate downward about hinge 1. (g = 10 m/s2). Choose the correct statement(s) :-

(A) The reaction at hinge 1, before hinge 2 breaks, is 11 N

(B) The reaction at hinge 1, before hinge 2 breaks, is 24 N
(C) The reaction at hinge 1, just after breaking of hinge 2 is 5N
(D) The reaction at hinge 1, just after breaking of hinge 2 is 8N

SECTION-III
Numerical Grid Type (Ranging from 0 to 9) 1 Q. [4 M (0)]

10. A thin uniform rod of length L and mass m = 1.6 kg is free to rotate about a smooth axis which
passes through its edge A. A point mass m is shot horizontally at a velocity of v 0 towards the
opposite edge of the rod (point B). When it hits the rod, it sticks to it. What is the magnitude of
the vertical component of force (in N) applied by the axis on the rod in the horizontal state?
(g = 10 m/s2)

Space for Rough Work

Assignment 3
 SECTION-IV
Comprehension Type 7 Q. [M 3(–1)]
Paragraph for Questions Nos. 11 & 12

A uniform stick with mass m and length  is pivoted at a point

from an end as shown in diagram.
4
A massless string hangs from each end of stick and wraps around the underside of a massless
pulley with diameter . A mass hangs from pulley. The stick is held horizontal initially and is
released from rest. After releasing-

11. Initial tension in the string is:

mg 7mg 3mg
(A) mg (B) (C) (D)
5 10 5
12. Initial acceleration of mass m is:
2g 3g g g
(A) (B) (C) (D)
5 5 5 3
Paragraph for Question Nos. 13 to 15
A smooth disc of mass M and radius R can rotate freely around a vertical axis supported by
frictionless bearings. A constraining vertical surface of negligible mass, whose shape is a
R
semicircular arc of radius r = , is fixed on the disc as shown in the figure. A small ball of mass
2
m is placed on the stationary disc and is bowled at a speed v in such a way that it reaches the
internal side of the constraining surface tangentially.

13. Mark the CORRECT statement :-

(A) Momentum of ball & disc system is conserved
(B) Mechanical energy of ball & disc system is not conserved
(C) Angular momentum of ball & disc system is conserved
(D) Mechanical energy of ball & disc system is not conserved due to impulsive reaction from
support bearings
Space for Rough Work

Assignment 4
14. What is speed of the ball when it leaves the disc:-

M m 2M M
(A) v (B) v (C) v (D) 2v
M + 2m M + 2m M+m 2M + m

15. What is angular velocity of disc when ball leaves it :-

mv M mv m mv 2M mv M
(A) 2 (B) 2 (C) 2 (D) 2
MR M + 2m MR M + 2m MR M + m MR 2M + m

Paragraph for Question Nos. 16 & 17

A small particle of mass m is given an initial velocity v 0 tangent to the horizontal rim of a smooth
cone of base radius r0 from the vertical centerline as shown at point A. As the particle slides to
point B, a vertical distance h below A, its velocity v makes an angle  with the horizontal tangent
to the cone through B.

16. The value of  and speed of the particle at point B are respectively :-
v0r0 v0r0
(A) cos−1 , v02 + 2gh (B) cos−1 , v02 + 2gh
(r0 − htan  ) v02 + 2gh (r0 + htan  ) v02 + 2gh

v0r0 v0
(C) cos−1 , v02 − 2gh (D) cos−1 , v02 + 2gh
(r0 − htan  ) v02 − 2gh v02 + 2gh

17. The minimum value of v0 for which particle will be moving in a horizontal circle of radius r 0 :-
2gr0 gr0 gr0 4gr0
(A) (B) (C) (D)
tan 2 tan tan tan

Space for Rough Work

Assignment 5
Match the Matrix type 1 Q. [M 8 (0)]
(Partial marking → each correct answer contains +2 marks)

18. A small ball of mass m moving horizontally with speed v0 = 2g strike a uniform rod of equal
mass and length  as shown in diagram. The ball comes to rest just after the collision. Then

List-I Liat-II
(P) Angular velocity of rod just after collision (1) 2m2g
27
(Q) Impulse due to hinge during collision (2) mg
16
81 g
(R) Impulse on rod by ball (3)
8
m2 g
(D) Kinetic energy of rod just after collision (4)
32

________________________THANK YOU_________________________

Space for Rough Work

Assignment 6