Assignment - 2024 - Week - 1 - With Solution

NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
Course Name: Experimental Robotics

Assignment- Week 1
TYPE OF QUESTION: MCQ/MSQ
Number of questions: 10 Total mark: 10 X 2 = 20
______________________________________________________________________________
QUESTION 1:
Teaching aims to
a)
make a robot intelligent.
b)
pass instructions to a robot.
c)
both (a) and (b).
d)
none of the above.
Correct Answer: (b)
Detailed Solution:
Teaching aims to pass the instructions to a robot.
______________________________________________________________________________
QUESTION 2:
Teach-pendant used for teaching a robot is a
a) Remote controller.
b) Software package.
c) Virtual reality (VR) tool.
d) None of the above.
Correct Answer: (a)
Detailed Solution:
Teach-pendant used for teaching a robot is a remote-controller, which passes the instructions to a
robot.
______________________________________________________________________________
QUESTION 3:
The task of making a few drilled holes on a steel plate is an example of
a) continuous path task.
b) point-to-point task.
c) both (a) and (b).

d) none of the above.
Correct Answer: (b)
Detailed Solution:
Drilling holes in a steel plate is a point-to-point task.
______________________________________________________________________________
QUESTION 4:
The task of cutting a complicated profile (non-linear) on one side of the steel plate is an example
of
a) continuous path task.

b) point-to-point task.
c) both (a) and (b).
d) none of the above.
Correct Answer: (a)
Detailed Solution:
While cutting a complicated profile on one side of the steel plate, the tool remains in continuous
contact with the plate, hence it is a continuous path task.
______________________________________________________________________________
QUESTION 5:
During online teaching of a robot
a) the robot to be taught is used.
b) the robot to be taught is not used.
c) compiler program is used.
d) its electrical power is to be switched off.
Correct Answer: (a)
Detailed Solution:
During online teaching of a robot, the robot to be taught is used.
____________________________________________________________________________
QUESTION 6:
Manipulator is
a) a mobile robot.
b) a robot capable of negotiating the staircase.
c) a robot with fixed base.
d) not a robot at all.
Correct Answer: (c)
Detailed Solution:
A manipulator is a robot with fixed base.
____________________________________________________________________________
QUESTION 7:
Which one of the following move commands is used for generating linear motion of the end-effector of a
serial manipulator in Cartesian space?
a) MoveL
b) MoveJ
c) MoveP
d) MoveC
Correct Answer: (a)
Detailed Solution:
MoveL command is used for generating linear motion of the end-effector of a serial manipulator in
Cartesian space.
____________________________________________________________________________
QUESTION 8:
Universal Robot (UR5) can be used for
a) assembling automotive parts.
b) precise spray paintings.
c) pick and place tasks.
d) all of the above.
Correct Answer: (d)

Detailed Solution:
Universal robot (UR5) can be used for various applications, such as assembling automotive parts, precise
spray painting, pick and place task etc.
______________________________________________________________________
QUESTION 9:
Universal Robot (UR5) has
a) 4 degrees of freedom (dof).
b) 3 dof
c) 5 dof
d) 6 dof
Correct Answer: (d)
Detailed Solution:
Universal Robot (UR5) has 6 dof.
______________________________________________________________________
QUESTION 10:
The workspace of a manipulator is defined as
a)the volume occupied by it, during its stationary condition.
b)the ranges of motion of its joints.
c)the control panel or interface used to operate the manipulator.
d)3D volume in space within which the end-effector of the manipulator can move at any
position.
Correct Answer: (d)
Detailed Solution:
The 3D volume within which the end-effector of the manipulator can move with various orientations is
defined as workspace of a manipulator.
______________________________________________________________________________
************END*******

Assignment - 2024 - Week - 1 - With Solution

Uploaded by

Copyright:

Available Formats

Assignment - 2024 - Week - 1 - With Solution

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Assignment - 2024 - Week - 1 - With Solution

Uploaded by

Copyright:

Available Formats

NPTEL Online Certification Courses

Indian Institute of Technology Kharagpur

Course Name: Experimental Robotics

Teaching aims to pass the instructions to a robot.

c) both (a) and (b).

Drilling holes in a steel plate is a point-to-point task.

a) continuous path task.

Correct Answer: (a)

During online teaching of a robot, the robot to be taught is used.

A manipulator is a robot with fixed base.

Correct Answer: (a)

Correct Answer: (d)

Correct Answer: (d)

Universal Robot (UR5) has 6 dof.

You might also like