REPAIRING ROWE/AMI R84 - R88

CENTRAL CONTROL COMPUTERS

Using The Jukebox Troubleshooter ...

• Comes with two 20-pin strip headers and PC serial cable

• Uses a PC serial port for interactive control
• Full memory IC diagnostics and battery check
• Performs continuous record mechanism testing
• Verify LED display digits and indicators
• Outputs stationary signals for voltmeter troubleshooting
• Test operation of all push -button and slide switches
• Displays coin switch activity
• Locates and identifies intermittent connections
• Shows mechanism INDEX and HOME signal timing
• Check pricing board configuration and program cards
• Increment Play counter and Money counter
• Manual has tips, charts, voltage readings and schematics
• 99% of all board components tested, except crystal Y100

TEL: (908) 362-6299

Data Sync Engineering FAX: (908) 362-5889
P.O. Box 539, 2 Footbridge Lane
Blairstown, New Jersey 07825 www.datasynceng.com
www.cdadapter.com

Copyright © 2010 Data Sync Engineering. All Rights Reserved.

Designated trademarks and brands are the property of their respective owners.
 PREPARING THE CENTRAL CONTROL COMPUTER CIRCUIT BOARD

NOTCH

PC CABLE

IC SOCKET

MOD UPDATE

To use the Troubleshooter, you need to remove the custom microprocessor chip and insert a 40-pin IC socket. A low profile,
dual leaf type socket, such as 3M part number 4840-6004-CP, is recommended.
The controller chip used in this board is very rare and is no longer available, so you must be very careful when you remove it.
Use a low wattage soldering iron and a desoldering tool to remove the solder from the IC pads. Do not heat the pad for too long
or it will be damaged and lift off the board. Carefully wiggle each lead with a needle-nose pliers to free it from the pad. Gently
pry the IC from the board using a small screwdriver at each end. Do not apply excessive force or you will break a pin.
Insert the 40-pin IC socket with the notch facing up. After soldering the pins, you can remove the residual flux using 91%
Isopropyl alcohol.
TIP ... A Mod Update was issued for CCC board # 6-09971-01, wire jumper W222 was changed to a 220 Ohm 1/4W resistor.

Some board failures are caused by solder joint fractures at the connector
pins. This happens when a connector is inserted, which creates pressure
on the pin, causing it to push through. The foam padding behind the circuit
board was used to relieve this pressure, but in many cases, is either BROKEN SOLDER
deteriorated or missing altogether. It is best to remove the old solder and
resolder these connector pins then clean off the residual flux. You can
replace the foam padding with a 1/4" thick rubber mouse pad.

Two circuit board types were produced. The first board was # 6-08871-01
which used the Rockwell 6500 microprocessor IC, the next board was part
# 6-08871-04 and used the Mostek 3870 microprocessor. These chips are
not interchangeable because of the pinout differences. It is also important
to know this when using the Troubleshooter board. You must use the
proper position, either the U2 6500 CCC-01 or U1 3870 CCC-04.
 PLUGGING IN TROUBLESHOOTER BOARD

For 6-08871-04 For 6-08871-01

At the bottom side of the tester board are two 40-pin IC sockets.
Two 20-pin strip headers will be inserted into one of these
sockets. The board under test here is part # 6-08871-01 which
uses the U2 socket position. Gently press the pin strip into the
socket, being careful not to bend the pins.

Now insert the tester board

into the IC socket. Make sure
the pins line up with the
socket then gently press
down.

On the PC Serial cable, plug

the 6-pin white connector end PC Serial Port
into P-103 on the Central
Control Computer board.

The 9-pin DSUB connector

end plugs into your PC's serial
port connector.

If you don't have a serial port,

then you need to get a USB to
Tester board LED Serial Port adapter cable.

USB to Serial Adapter

 SETTING UP THE MICROSOFT WINDOWS HYPERTERMINAL PROGRAM

On your PC ...

Click Start | All Programs | Accessories | Communications | click on HyperTerminal

At Connection Name: enter something like Jukebox

At Connect Using: select a serial port COM number (usually shows a list of COM#'s available)

Port Settings

Bits per second: 9600

Data bits: 8
Parity: None
Stop bits: 1
Flow control: None

Click OK

Click File | Properties | Settings | ASCII Setup

Only boxes checked should be

Append line feeds to incoming line ends

Wrap lines that exceed terminal width

Click OK then OK

If you wish to capture and save the Troubleshooter activity to a file ...

Click Transfer | Capture Text

Enter the name of the folder and file you want to save the report to

Click Start

Select Troubleshooter command functions

When finished

Click Transfer | Capture Text | Stop

THE PC SERIAL PORT DATA CABLE

5 Molex .156 KK

To Jukebox
To PC 3 Central
Serial WHT 3
Control
COM
2 RED 4 Computer
Port
P-103

Female
DB9
 STARTING UP THE TROUBLESHOOTER PROGRAM

When the Central Control Computer board is powered up, the tester board LED should light and start up message displayed.
If the tester board LED is not on ...
Did you use the correct U1 or U2 position ? Does the socket have 5-volt power ? Is the RESET signal 2-volts or higher ?

Rowe R84-R88 Jukebox Troubleshooter

Rev 1.1, 03/07/10 Data Sync Engineering
---------------------------------------

CMD>

To see a list of all available command functions, type the question mark (?) character:

CMD>?

0 - STROBE 0
1 - STROBE 1
2 - STROBE 2
3 - STROBE 3
4 - STROBE 4
5 - STROBE 5
6 - STROBE 6
7 - STROBE 7
8 - STROBE 8
9 - STROBE 9
A - Run All Tests (Memory and Mechanism)
C - Control Computer LED Display Check
D - Dump STROBE/RETURN Data Map
F - Fill RAM Memory
H - Move Mechanism to HOME Position
I - Interrogate STROBE/RETURN Activity
J - Jukebox LED Display Check
M - Record Mechanism Test
P - Print RAM Contents
R - RAM Memory Test
S - Show All Active Signals (as Text)
X - Increment Play Counter
Z - Increment Coin Counter
CMD>

STROBE Commands

The STROBE commands activate 1 of 10 output signals, in a stationary state (high or low), so you would only need a voltmeter
to do circuit troubleshooting. The "STROBE OUTPUTS" page shows the voltage readings for each STROBE state. The 1's and
0's display the current logic state of the RETURN input signals. A logic "0" indicates an active or on signal. The "RETURN
INPUTS" page shows the RETURN signal map for each of the associated STROBE signals.

For example, if STROBE7 is selected (pressed "7" on the PC keyboard), the following will display:

CMD>7
STROBE7: 1 1 1 1 1 1 1 1

The STROBE7 output signal is continuously held active and the RETURN signal state displayed. Any change of the RETURN
signal state will cause a display update. The following display shows this when a quarter was deposited.
A review of the RETURN signal map (RETURN INPUTS page) shows this signal or bit position to be the "25¢ Coin Switch".

STROBE7: 1 1 0 1 1 1 1 1 0 = switch ON
STROBE7: 1 1 1 1 1 1 1 1 1 = switch OFF
Run All Tests (Memory and Mechanism)

This is a continuously running test that checks RAM memory and Mechanism operations.

For the memory test, the "RAM Retention Data" may fail on the first time because the check pattern has not been written. This
check pattern is used to verify the battery backup circuit. After the first time through, turn the power off, wait about 5-minutes,
turn the power on then run this test. The "RAM Retention Data" test should pass.

For the mechanism test, the record magazine is rotated then stopped at record number 50. During the rotation, pulse
measurements are recorded and displayed for the HOME and INDEX optical signals. When record 50 is reached, it is
transferred to the turntable and played. The "A" and "B" side is toggled at each record play cycle. The Pass Number count is
displayed after each cycle. Every test step position is displayed.

CMD>A
---------------------------------------
- Starting All Tests ...

- Checking RAM Backup Battery: Good

- Checking RAM Retention Data: Failed
- Running RAM Memory Data Test ...
...... Sequential Pattern
...... Address into Address
- Writing RAM Retention Pattern

---------------------------------------
Starting Mechanism Test ...

- INNER CAM was not low

- Transfer Motor on
- Waiting for INNER CAM signal low
- Transfer Motor off
- Detent on, magazine unlocked
- Magazine Motor on
- Waiting for HOME signal high
- Waiting for HOME signal low
- Waiting for INDEX signal high
- Waiting for INDEX signal low
...... HOME to Start of INDEX: 20 mS
...... End of INDEX to HOME: 13 mS
...... HOME signal pulse width: 58 mS
...... Index ON pulse width: 25 mS
...... Index OFF pulse width: 33 mS
- HOME and 51 INDEX pulses ...................................................
- Detent off, magazine locked
- Magazine Motor off
- Should be at record position 50
- Turntable motor on
- Transfer Motor on
- Waiting for INNER CAM signal high
- Waiting for OUTER CAM signal low
- Transfer Motor off
- Playing (CANCEL or any key stops)
- Transfer Motor on
- Waiting for INNER CAM signal low
- Transfer Motor off
- Turntable motor off
=======================================
Pass Number: 1
=======================================

- Checking RAM Backup Battery: Good

- Checking RAM Retention Data: Passed
- Running RAM Memory Data Test ...
Control Computer LED Display Check

All display digits should be lit on the Central Control Computer board. Check LED segment brightness.

CMD>C
- Control Computer LED Display Check

Dump STROBE/RETURN Data Map

Displays all STROBE/RETURN signals. "1" = signal off, "0" = signal active or on.

CMD>D

RETURNS 7 6 5 4 3 2 1 0
-------------------------
STROBE0: 1 1 1 1 1 1 1 1
STROBE1: 1 0 1 1 1 1 1 1
STROBE2: 1 1 1 1 1 0 1 0
STROBE3: 1 1 1 1 1 1 1 0
STROBE4: 1 1 1 1 1 1 0 0
STROBE5: 1 1 1 1 1 0 1 0
STROBE6: 1 1 0 1 1 0 0 0
STROBE7: 1 1 1 1 1 1 1 1
STROBE8: 1 1 1 1 1 1 1 1
STROBE9: 1 1 1 1 1 1 1 1

Fill RAM Memory

Writes the specified data pattern to RAM memory (in HEX). See "NUMBERS CONVERSION CHART" page.

CMD>F Hex pattern "55"

- Fill RAM Memory, Hex Pattern: 55 was entered

Move Mechanism to HOME Position

Moves the record magazine to HOME position which is record number 99.

CMD>H
- Moving to HOME Position

Interrogate STROBE/RETURN Activity

This is a powerful diagnostic tool that displays the ON (+) or OFF (-) state of any signal change. Wiggle wire harnesses to find
intermittent connections. Test buttons, switches and coin signals. Locate components that fail over time and temperature.

CMD>I
---------------------------------------
Interrogator Started ...

+Keypad "1"
-Keypad "1"
+Keypad "2"
-Keypad "2"
+Keypad "3"
-Keypad "3"
+Cancel Signal
-Cancel Signal
You can also use the Interrogate command function to check the mechanisms' INDEX and HOME opto sensor signals.
Move switch to "Service Mode" and press the "Cancel" button to start magazine rotation. HOME is active at record position 99.

+Service switch
+Cancel Signal
+Optical Index
-Optical Index
+Optical Home signal
+Optical Index
-Optical Index
-Optical Home signal
+Optical Index
-Optical Index
-Cancel Signal

Jukebox LED Display Check

All display digits & LED's should be lit on the jukebox front panel. Check LED segment brightness.

CMD>J
- Jukebox LED Display Check

Record Mechanism Test

Same as "Run All Tests" except for RAM memory test and display of Pass Number counts.

CMD>M
---------------------------------------
Starting Mechanism Test ...

- Detent on, magazine unlocked

- Magazine Motor on

Print RAM Contents

Displays the entire contents of RAM memory in HEX format. The example shows the data that was previously written using "Fill
RAM Memory" command. Can be used to locate data changes that occurred over time & temperature.

CMD>P

Printing RAM Contents

55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
RAM Memory Test

Performs all RAM Memory tests. Stops when a memory error is detected and displays the error result. The LED displays will
show random patterns during the memory test. In the example below, pin 11 on Z109 (data in, bit 2) was intentionally lifted off
the circuit board to create an error condition. ADDR is memory address being tested, WAS is the data pattern that was read
and SB is the data pattern that it should be. Z109 is the upper 4-bits, Z114 is the lower 4-bits.

CMD>R
- Checking RAM Backup Battery: Good
- Checking RAM Retention Data: Failed
- Running RAM Memory Data Test ...
ADDR: 0 0 0 0 0 0 0 0 WAS: 0 0 1 1 0 0 0 0 SB: 0 0 0 1 0 0 0 0
- RAM test terminated ...
- Writing RAM Retention Pattern

Show All Active Signals (as Text)

Displays all active or on signals then enters Interrogator Mode. This is used to identify what signals should be or should not be
active (such as a stuck push-button switch). It can also be used to verify the pricing board configuration settings. The (CR###)
display is the diode designation number associated to that signal.

For example, the configuration for this machine is:

~ Order of play is "As Selected"
~ Price of Credit Level 1 is 25 cents
~ Card level 1 is 1 credit
~ Card level 2 is 3 credits
~ Card level 3 is 5 credits
~ Card level 4 is 7 credits
~ Inner Cam switch on = no record in play

CMD>S
---------------------------------------
Interrogator Started ...

+Standard/As Selected switch

+Price of Credit Level 1, 20c (CR326)
+Price of Credit Level 1, 5c (CR324)
+Card Level 1, =1 (CR312)
+Card Level 2, =2 (CR309)
+Card Level 2, =1 (CR308)
+Card Level 3, =4 (CR306)
+Card Level 3, =1 (CR304)
+Inner Cam switch
+Card Level 4, =4 (CR302)
+Card Level 4, =2 (CR301)
+Card Level 4, =1 (CR300)

Increment Play Counter

Causes the mechanical Total Plays counter to increment one position.

CMD>X
- Incrementing Play Counter

Increment Coin Counter

Causes the mechanical Money counter to increment one position.

CMD>Z
- Incrementing Coin Counter
 NUMBERS CONVERSION CHART
HEX / BINARY / DECIMAL
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
0000 0000 0000 0001 0000 0010 0000 0011 0000 0100 0000 0101 0000 0110 0000 0111 0000 1000 0000 1001 0000 1010 0000 1011 0000 1100 0000 1101 0000 1110 0000 1111
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F
0001 0000 0001 0001 0001 0010 0001 0011 0001 0100 0001 0101 0001 0110 0001 0111 0001 1000 0001 1001 0001 1010 0001 1011 0001 1100 0001 1101 0001 1110 0001 1111
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F
0010 0000 0010 0001 0010 0010 0010 0011 0010 0100 0010 0101 0010 0110 0010 0111 0010 1000 0010 1001 0010 1010 0010 1011 0010 1100 0010 1101 0010 1110 0010 1111
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0011 0000 0011 0001 0011 0010 0011 0011 0011 0100 0011 0101 0011 0110 0011 0111 0011 1000 0011 1001 0011 1010 0011 1011 0011 1100 0011 1101 0011 1110 0011 1111
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F
0100 0000 0100 0001 0100 0010 0100 0011 0100 0100 0100 0101 0100 0110 0100 0111 0100 1000 0100 1001 0100 1010 0100 1011 0100 1100 0100 1101 0100 1110 0100 1111
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F
0101 0000 0101 0001 0101 0010 0101 0011 0101 0100 0101 0101 0101 0110 0101 0111 0101 1000 0101 1001 0101 1010 0101 1011 0101 1100 0101 1101 0101 1110 0101 1111
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95

60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F
0110 0000 0110 0001 0110 0010 0110 0011 0110 0100 0110 0101 0110 0110 0110 0111 0110 1000 0110 1001 0110 1010 0110 1011 0110 1100 0110 1101 0110 1110 0110 1111
96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111

70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F
0111 0000 0111 0001 0111 0010 0111 0011 0111 0100 0111 0101 0111 0110 0111 0111 0111 1000 0111 1001 0111 1010 0111 1011 0111 1100 0111 1101 0111 1110 0111 1111
112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127

80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F
1000 0000 1000 0001 1000 0010 1000 0011 1000 0100 1000 0101 1000 0110 1000 0111 1000 1000 1000 1001 1000 1010 1000 1011 1000 1100 1000 1101 1000 1110 1000 1111
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143

90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F
1001 0000 1001 0001 1001 0010 1001 0011 1001 0100 1001 0101 1001 0110 1001 0111 1001 1000 1001 1001 1001 1010 1001 1011 1001 1100 1001 1101 1001 1110 1001 1111
144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF
1010 0000 1010 0001 1010 0010 1010 0011 1010 0100 1010 0101 1010 0110 1010 0111 1010 1000 1010 1001 1010 1010 1010 1011 1010 1100 1010 1101 1010 1110 1010 1111
160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175

B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF
1011 0000 1011 0001 1011 0010 1011 0011 1011 0100 1011 0101 1011 0110 1011 0111 1011 1000 1011 1001 1011 1010 1011 1011 1011 1100 1011 1101 1011 1110 1011 1111
176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191

C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF
1100 0000 1100 0001 1100 0010 1100 0011 1100 0100 1100 0101 1100 0110 1100 0111 1100 1000 1100 1001 1100 1010 1100 1011 1100 1100 1100 1101 1100 1110 1100 1111
192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207

D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF
1101 0000 1101 0001 1101 0010 1101 0011 1101 0100 1101 0101 1101 0110 1101 0111 1101 1000 1101 1001 1101 1010 1101 1011 1101 1100 1101 1101 1101 1110 1101 1111
208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223

E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF
1110 0000 1110 0001 1110 0010 1110 0011 1110 0100 1110 0101 1110 0110 1110 0111 1110 1000 1110 1001 1110 1010 1110 1011 1110 1100 1110 1101 1110 1110 1110 1111
224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239

F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF
1111 0000 1111 0001 1111 0010 1111 0011 1111 0100 1111 0101 1111 0110 1111 0111 1111 1000 1111 1001 1111 1010 1111 1011 1111 1100 1111 1101 1111 1110 1111 1111
240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255
 STROBE OUTPUTS
STROBE
VOLTAGES
P100 +8V
OFF 0V MICROCOMPUTER
NSDU45 (x10) 16

R108

R109

R110

R107
1 KEY ON 6.8V
VDD Z115 Z115
C B 3
STROBE0 Q0
E -01 Board -04 Board
"0" 9 Q103
6500 3870
C B 14
STROBE1

100K

100K

100K

100K
Q1
E
"1" 4 Q107
+2V

1 OF 10 DECODER
C B 2
STROBE2 Q2
E 3 11 20 8
"2" 3 Q102 13 PC0 P40
10
C A 10
B 15
STROBE3 Q3
E
"3" 5 Q104 19 9
5
C 13 2 PC1 P41
B 1 B
STROBE4 Q4 4
E
"4" 10 Q101
C 7 18 10
B 6 PC2 P42
STROBE5 Q5 12 1

CD4028
E C 6
"5" 2 Q108
C
B 7
STROBE6 Q6 9 17 11
E 11 14 PC3 P43
"6" 6 Q109 D 8
C
B 4
STROBE7 12

Z100
Q7 Z105
E
"7" 8 Q105
LM339
C B 9
STROBE8 Q8
E
"8" 11 Q100
C B 5
STROBE9 Q9
E
"9" 7 Q106 VSS
8

1K (x9)
STROBE
OUTPUTS Use PC keys 0 through 9 to select
STROBE outputs 0 through 9
R105
R100

R104

R106

R121
R101
R119

R102
R120

R103

VOLTMETER MEASUREMENTS
STROBE0 STROBE1 STROBE2 STROBE3 STROBE4 STROBE5 STROBE6 STROBE7 STROBE8 STROBE9
P100-9 P100-4 P100-3 P100-5 P100-10 P100-2 P100-6 P100-8 P100-11 P100-7
CMD "0" CMD "1" CMD "2" CMD "3" CMD "4" CMD "5" CMD "6" CMD "7" CMD "8" CMD "9"
Z105-5 0V 0V +5V +5V 0V 0V +5V +5V 0V 0V
Z105-7 0V 0V 0V 0V +5V +5V +5V +5V 0V 0V
Z105-9 0V 0V 0V 0V 0V 0V 0V 0V +5V +5V
Z105-11 0V +5V 0V +5V 0V +5V 0V +5V 0V +5V
Z100-1 0V 0V 0V 0V +8V 0V 0V 0V 0V 0V
Z100-2 0V 0V +8V 0V 0V 0V 0V 0V 0V 0V
Z100-3 +8V 0V 0V 0V 0V 0V 0V 0V 0V 0V
Z100-4 0V 0V 0V 0V 0V 0V 0V +8V 0V 0V
Z100-5 0V 0V 0V 0V 0V 0V 0V 0V 0V +8V
Z100-6 0V 0V 0V 0V 0V +8V 0V 0V 0V 0V
Z100-7 0V 0V 0V 0V 0V 0V +8V 0V 0V 0V
Z100-9 0V 0V 0V 0V 0V 0V 0V 0V +8V 0V
Z100-10 0V +8V 0V +8V 0V +8V 0V +8V 0V +8V
Z100-11 0V 0V 0V 0V 0V 0V 0V 0V +8V +8V
Z100-12 0V 0V 0V 0V +8V +8V +8V +8V 0V 0V
Z100-13 0V 0V +8V +8V 0V 0V +8V +8V 0V 0V
Z100-14 0V +8V 0V 0V 0V 0V 0V 0V 0V 0V
Z100-15 0V 0V 0V +8V 0V 0V 0V 0V 0V 0V
 RETURN INPUTS

RETURN
VOLTAGES
OFF 5V
ON 0V
MICROCOMPUTER
R123 +8V
4 3
RETURN7 2 2 16
470 5 PD7 P07
VOLTAGE
RANGE
R124
OFF 0V 6
RETURN6 1 3 17
P101 ON 4-8V 470 7 PD6 P06

RETURN5
R128 10
"5" 10 13 4 18
470 11 PD5 P05

RETURN4
R127 8
"4" 9 14 5 19
470 9 PD4 P04
Z110
12
LM339 Z115 Z115
-01 Board -04 Board
RETURN3 +8V
R132
4 3 6500 3870
"3" 12 2 6 6
470 5 PD3 P03

RETURN2 R131
6
"2" 11 1 7 5
470 7 PD2 P02

RETURN1 R136
10
"1" 14 13 8 4
470 11 PD1 P01

RETURN0 R135 33 28
8 PA5 P55
"0" 13 14 9 3
470 9 PD0 P00
Z111
12 LM339
RETURN
1K

1K

1K

1K

1K

1K

1K
1K

.001

.001

.001

.001

.001

.001

.001

.001

+5V
INPUTS 3 9
R143 +2V
14
8
3.3K Z117 12
R134

C108
R137

C109
R130

C106
R133

C107
R126

C104
R129

C105
R122

C102
R125

C103

R179
+8V LM339
10K
5V when reading
2V when reading RETURN signals,
RETURN signals, otherwise, 0V.
otherwise, 8V.

"STROBE output" to "RETURN input" signal matrix Shaded area are the RETURN signals from the P101 Connector

RETURN 7 RETURN 6 RETURN 5 RETURN 4 RETURN 3 RETURN 2 RETURN 1 RETURN 0

+8 On Dollar Bill Bonus Prem Ratio Prem Ratio Prem Ratio Prem Ratio
STROBE 0 Cancel Signal
(service switch) 1 8 4 2 1
Dollar Bill Bonus 1 Play Price 1 Play Price 1 Play Price 1 Play Price
STROBE 1 Test Switch STD / As Selected
2 8 4 2 1
Clear Selection Price of Crd Lvl 1 Price of Crd Lvl 1 Price of Crd Lvl 1 Price of Crd Lvl 1
STROBE 2 Manual Credit Coin Ratio
Memory 40¢ 20¢ 10¢ 5¢
Most / Least Card Level 1 Card Level 1 Card Level 1 Card Level 1
STROBE 3 1, 2, 4, 8
Popular 8 4 2 1
Memorec Memorec Card Level 2 Card Level 2 Card Level 2 Card Level 2
STROBE 4 1, 2, 3, 5 1, 2, 5, 10
Reset Advance 8 4 2 1
Card Level 3 Card Level 3 Card Level 3 Card Level 3
STROBE 5 Playmaker Timer 16 Play Adder
8 4 2 1
Card Level 4 Card Level 4 Card Level 4 Card Level 4
STROBE 6 Optical Index Optical Home Inner Cam Switch Outer Cam Switch
8 4 2 1

STROBE 7 $1 Bill Switch 50¢ Coin Switch 25¢ Coin Switch 10¢ Coin Switch 5¢ Coin Switch 160 Play POPULAR RESET

STROBE 8 RI-3 5 4 3 2 1
Premium Price
STROBE 9 Key 0 9 8 7 6
 TRANSISTOR SWITCHES

Mod Update
STROBE5 STROBE0 STROBE6 Replace W222
6.8V W222 with 220 Ohm,
0V
R182
R194 1/4W resistor.
R140

6.1V
10K

7.3V 220 MPSA56

E E E E E E E
The PNP transistor is turned on
Q111

Q124

Q117
Q125

Q123

Q122

Q116
B B B B B B B
P105
when the Base voltage is about
C C C C C C C 0.7V below the Emitter voltage.
6.7V 10 Optical INDEX
0V
11 Optical HOME
10K
6 Outer Cam (N.O.)
R173 10K
5 Inner Cam (N.O.)
R174 4.7K
2 +8 ON Signal
10K R176
1 CANCEL Signal
R177
CR105

CR118

CR110
CR121

CR111
CR120

CR119

6.0V

R175

47K
0V
Playmaker
Timer
RETURN6 RETURN6 RETURN7 RETURN5 RETURN4 RETURN6 RETURN7
PLAYMAKER CANCEL SERVICE INNER OUTER HOME INDEX
TIMER SIGNAL MODE CAM CAM SIGNAL SIGNAL
ON The upper voltage reading is when the signal is on
OFF or active, the lower reading is when the signal is off.

"STROBE output" to "RETURN input" signal matrix Shaded area are the RETURN signals from the P101 Connector

RETURN 7 RETURN 6 RETURN 5 RETURN 4 RETURN 3 RETURN 2 RETURN 1 RETURN 0

+8 On Dollar Bill Bonus Prem Ratio Prem Ratio Prem Ratio Prem Ratio
STROBE 0 Cancel Signal
(service switch) 1 8 4 2 1
Dollar Bill Bonus 1 Play Price 1 Play Price 1 Play Price 1 Play Price
STROBE 1 Test Switch STD / As Selected
2 8 4 2 1
Clear Selection Price of Crd Lvl 1 Price of Crd Lvl 1 Price of Crd Lvl 1 Price of Crd Lvl 1
STROBE 2 Manual Credit Coin Ratio
Memory 40¢ 20¢ 10¢ 5¢
Most / Least Card Level 1 Card Level 1 Card Level 1 Card Level 1
STROBE 3 1, 2, 4, 8
Popular 8 4 2 1
Memorec Memorec Card Level 2 Card Level 2 Card Level 2 Card Level 2
STROBE 4 1, 2, 3, 5 1, 2, 5, 10
Reset Advance 8 4 2 1
Card Level 3 Card Level 3 Card Level 3 Card Level 3
STROBE 5 Playmaker Timer 16 Play Adder
8 4 2 1
Card Level 4 Card Level 4 Card Level 4 Card Level 4
STROBE 6 Optical Index Optical Home Inner Cam Switch Outer Cam Switch
8 4 2 1

STROBE 7 $1 Bill Switch 50¢ Coin Switch 25¢ Coin Switch 10¢ Coin Switch 5¢ Coin Switch 160 Play POPULAR RESET

STROBE 8 RI-3 5 4 3 2 1
Premium Price
STROBE 9 Key 0 9 8 7 6

MECHANICAL SWITCHES, PROGRAM DIODES & CARDS

All other switches, including coin and keypad, use the same Active or ON signals
MANUAL
circuitry, a switch, the appropriate STROBE / RETURN CREDIT
are valid between
4 to 8 volts.
signals and a diode. 1N914A
STROBE2 RETURN6
Programming cards and diodes use a fixed circuit trace
S105 CR106
instead of a switch. 6.7V 6.7V 6.0V
0V 0V 0V
The matrix above shows the STROBE / RETURN correlation
of all signals.
 LED DISPLAY

14 +5V P101
2 16 1
PD7 P07 3 4 13
2 Z106 5 "G"
6 "F"
3 17 6
PD6 P06 4 5 12 8 "E"
5 Z106
7 "D"
4 18 9 4 "C"
PD5 P05 10 7 10
8 Z106 3 "B"

2 "A"
5 19 12

68

68

68

68

68

68

68
PD4 P04 11 6 11
13 Z106 SEGMENT
Z108 OUTPUTS

R115

R114

R113

R117

R116

R118

R112
7 CD4001 ULN2003
14 +5V 1 13 10 8 7 2 11
6 6 1
PD3 P03 3 3 14 a b c d e f g
2 Z107

7 5 6
PD2 P02 4
5 Z107

8 4 9
PD1 P01 10 2 15
3 9 14 3 9 14 3 9 14 3 9 14
8 Z107

CR126
CR124

CR127
9 3 12

CR125
PD0 P00 11 1 16
13 Z107
Z115 Z115 8
7 CD4001 STROBE7 STROBE8 STROBE5 STROBE6
10K

-01 Board -04 Board

R193

6500 3870
34 29
PA4 P54
NOTE: Resistor R193 and diodes
CR124, CR125, CR126 and CR127
are not used on the -01 board.

P07 (3870) P06 (3870) P05 (3870) P04 (3870) P03 (3870) P02 (3870) P01 (3870) P00 (3870)
PD7 (6500) PD6 (6500) PD5 (6500) PD4 (6500) PD3 (6500) PD2 (6500) PD1 (6500) PD0 (6500)
Segment G Segment F Segment E Segment D Segment C Segment B Segment A
Selections Selection Most Selection Being Make Standard Make Any
STROBE 0 Remaining Playing Popular Made Selection Selection
User Display User Display User Display User Display User Display User Display User Display
STROBE 1 1st Digit 1st Digit 1st Digit 1st Digit 1st Digit 1st Digit 1st Digit
User Display User Display User Display User Display User Display User Display User Display
STROBE 2 2nd Digit 2nd Digit 2nd Digit 2nd Digit 2nd Digit 2nd Digit 2nd Digit
User Display User Display User Display User Display User Display User Display User Display
STROBE 3 3rd Digit 3rd Digit 3rd Digit 3rd Digit 3rd Digit 3rd Digit 3rd Digit

STROBE 4

CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display
STROBE 5 3rd Digit 3rd Digit 3rd Digit 3rd Digit 3rd Digit 3rd Digit 3rd Digit
CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display
STROBE 6 4th Digit 4th Digit 4th Digit 4th Digit 4th Digit 4th Digit 4th Digit
CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display
STROBE 7 1st Digit 1st Digit 1st Digit 1st Digit 1st Digit 1st Digit 1st Digit
CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display CCC Display
STROBE 8 2nd Digit 2nd Digit 2nd Digit 2nd Digit 2nd Digit 2nd Digit 2nd Digit

STROBE 9
 VOLTAGE MONITOR / POWER SUPPLY REGULATOR FOR -01 BOARD

ROCKWELL -01 BOARD

RAM MEMORY ENABLE

RAM MEMORY POWER & BATTERY CHARGER

4.93

7.93

5.60

5.00 7.93
5.00

5.60
4.97 2.01
2.01
3.01
4.34

4.88 4.90

2.38

3.67

CR109 DIODE, Zener, 1N4733A, 5.1V, 1W

CR122 DIODE, Signal, 1N914

CR123 DIODE, Rectifier, 1N4002, 100V, 1A

Q112 TRANSISTOR, NPN, MPS-A06, 500mA, 80V

Q113 TRANSISTOR, NPN, TIP31A, 60V, 3A

Q114 TRANSISTOR, NPN, MPS-A06, 500mA, 80V

Z115 IC, R6500, (CUSTOM MICROCONTROLLER)

Z117 IC, LM3302 / LM339, Quad Voltage Comparator

 VOLTAGE MONITOR / POWER SUPPLY REGULATOR FOR -04 BOARD

MOSTEK -04 BOARD

RAM MEMORY ENABLE

RAM MEMORY POWER & BATTERY CHARGER
5.02
8.00

5.70
5.07 8.00

5.68
5.70

4.90
5.68
2.05 2.05
5.64

3.42
5.00
5.55 5.50

2.40

4.35

CR109 DIODE, Zener, 1N4733A, 5.1V, 1W

CR122 DIODE, Signal, 1N914

Q112 TRANSISTOR, NPN, MPS-A06, 500mA, 80V

Q114 TRANSISTOR, NPN, MPS-A06, 500mA, 80V

Q126 TRANSISTOR, PNP, MPS-A56, 500mA, 80V

VR100 IC, LM340T-5 / LM7805, +5V Regulator, 1A

Z115 IC, MK3870, (CUSTOM MICROCONTROLLER)

Z117 IC, LM3302 / LM339, Quad Voltage Comparator

MEMORY BACK -UP BATTERY / BATTERY VOLTAGE DETECTOR

The original back-up battery is most likely "very old" and will cause
acid damage if leaking (green corrosion). You can replace it with a
dual AAA battery holder (Mouser 122-0421-GR), double-side foam
tape and new rechargeable Nickel-Metal Hydride AAA batteries.
TIP ... Use a cotton swap with household ammonia to remove the
green corrosion, afterwards, rinse and blow dry.

Rockwell -01 Board

4.93

2.01
0.44
7.32
2.01

2.71 4.92

4.33
4.93

Mostek -04 Board

5.03

2.05

6.76 0.75
2.05

5.05
2.69

5.00

5.03
(LEFT) SCHEMATIC DIAGRAM 6 -08871-01
SCHEMATIC DIAGRAM 6 -08871-01 (RIGHT)
(LEFT) SCHEMATIC DIAGRAM 6 -08871-04
SCHEMATIC DIAGRAM 6 -08871-04 (RIGHT)