Cidiagdd
Cidiagdd
*1 *2 *3 *1 *2 *4 I38587
Check Result/*2
HINT:
Result codes for all devices are shown below.
Result Meaning Action
The device did not respond with a DTC (excluding commu-
OK –
nication DTCs from the AVC–LAN).
Look up the DTC in ”Unit Check Mode” and replace the de-
EXCH The device responds with a ”replace”–type DTC.
vice.
CHEK The device responds with a ”check”–type DTC. Look up the DTC in ”Unit Check Mode”.
The device was previously present, but does not respond in 1. Check power supply wire harness of the device.
NCON
diagnostic mode. 2. Check the AVC–LAN of the device.
Old The device responds with an ”old”–type DTC. Look up the DTC in ”Unit Check Mode”.
The device responds in diagnostic mode, but gives no DTC 1. Check power supply wire harness of the device.
NRES
information. 2. Check the AVC–LAN of the device.
Code Clear/*3
Present DTCs are cleared.
Memory Clear/*4
Present and past DTCs and registered connected device names are cleared.
(b) Diagnosis MENU Display
I38666
HINT:
Each item is grayed out or not displayed based on the device settings.
*1
*5 *6
*2 *3 *4 I38588
Screen Description
Display Contents
Device name/*1 Target Device
Segment/*2 Target Device Logical address
DTC/*3 DTC (Diagnostic Trouble Code)
Timestamp/*4 The time and date of past DTCs displayed. (The year is displayed in 2 digit format.)
Present Code/*5 The DTC output at the service check is displayed.
Past Code/*6 Diagnostic memory results and recorded DTCs are displayed.
*1
I38589
Check result
HINT:
Check results of all the devices are displayed.
Result Meaning Action
No Err
There are no communication DTCs. –
(OK)
CHEK The device responds with a ”check”–type DTC. Look up the DTC in ”Unit Check Mode”.
The device was previously present, but does not respond in 1. Check power supply wire harness of the device.
NCON
diagnostic mode. 2. Check the AVC–LAN of the device.
Old The device responded with an old–type DTC. Look up the DTC in ”Unit Check Mode”.
Device responds in diagnostic mode, but gives no DTC 1. Check power supply wire harness of the device.
NRES
information. 2. Check the AVC–LAN of the device.
*1
*2
*3 *4 *5 *6 I38590
Screen Description
Display Contents
Device name/*1 Target device
Segment/*2 Target logical address
DTC/*3 DTC (Diagnostic Trouble Code)
Sub–Code (device address)/*4 Physical address stored with DTC. (If there is no address, nothing is displayed.)
Connection check No./*5 Connection check number stored with DTC.
DTC occurrence/*6 Number of times the same DTC has been recorded.
2. DISPLAY CHECK
(a) Vehicle Signal Check Mode Screen
I38591
Screen Description
Name Contents
Battery Battery voltage is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
IG Power switch ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with)/ BRIGHT (without) is displayed.
SPEED The vehicle speed, displayed in km/h.
TAIL TAIL signal (Head lamp dimmer switch) ON/OFF state is displayed.
HINT:
Only items sending a vehicle signal will be displayed.
This screen is updated once per second when input signals to the vehicle are changed.
3. NAVIGATION CHECK
(a) Navigation Check MENU Screen
I38667
HINT:
Each item is grayed out or not displayed based on the device settings.
(b) GPS information Screen
*1 *1
*2
*2
*5
*3
*4 I38592
Satellite information/*1
Information from a maximum of 12 satellites is displayed on the screen. This information includes the target
GPS satellite number, elevation angle, direction and signal level.
Receiving condition/*2
(DENSO model)
Display Contents
T The system is receiving a GPS signal, but is not using it for location.
P The system is using the GPS signal for location.
– The system cannot receive a GPS signal.
(AISIN AW Model)
Display Contents
01H The system cannot receive a GPS signal.
02H The system is tracing a satellite.
03H The system is receiving a GPS signal, but is not using it for location.
04H The system is using the GPS signal for location.
Measurement information/*3
Display Contents
2D 2–dimensional location method is being used.
3D 3–dimensional location method is being used.
NG Location data cannot be used.
Error Reception error has occurred.
– Any other state.
Position information/*4
Display Contents
Position Latitude and longitude information on the current position is displayed.
Date information/*5
Display Contents
The date/time information obtained from GPS signal is displayed in Greenwich
Date
mean time (GMT). The last 4 digits are displayed.
*1
*2
*3
I38593
Vehicle signal
Display Contents
REV/*1 REV signal ON/OFF state is displayed.
SPD/*2 SPD signal condition is displayed.
Sensor signal
Display Contents
Gyro sensor output condition is displayed (when the vehicle runs straight or is sta-
Gyro sensor/*3
tionary, the voltage is approximately 2.5 V).
HINT:
Signals are updated once per second only when vehicle sensor signals are changed.
(d) Parts Information Screen
*1
*2
*3
*4
I38594
Screen description
Display Contents
Navigation Manufacturer/*1 Navigation ECU manufacturer is displayed.
Navigation Version No./*2 Navigation ECU version is displayed.
Disc Manufacturer/*3 Map disc manufacturer is displayed.
Disc Version No./*4 Map disc version is displayed.
I38595
HINT:
This function cannot be used.