Scribd
Upload
23 views3 pages

8 Channel PWM Power

The document provides a list of components for an electronics project including resistors, capacitors, diodes, LEDs, ICs, MOSFETs, and switches. It also provides additional details on component specifications, alternatives, and sourcing.

Uploaded by

FRANCISCO VILLA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
23 views3 pages

8 Channel PWM Power

The document provides a list of components for an electronics project including resistors, capacitors, diodes, LEDs, ICs, MOSFETs, and switches. It also provides additional details on component specifications, alternatives, and sourcing.

Uploaded by

FRANCISCO VILLA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Identifier Description Qty

R1-R8 330R 8
R9,R11,R13,R15,R17,R19,R21,R23 120R 8
R10,R12,R14,R16,R18,R20,R22,R24 47K 8
R25,R26 10K 2
C1 330nF, polyester, 5mm pitch 1
C2,C4 100nF, muli-layer ceramic, 2.5mm pitch 2
D1,D14 1N4003 2
LED1 to LED8 5mm LED, high brightness, Red 8
IC1 7805, 1 amp, 5 volt regulator 1
IC2 PIC16F628A (requires programming) 1
STP36NF06L logic level N-channel MOSFET
Q1 to Q8 8
(STP20NF06L alternative)
S1 6mm right angle tactile switch 1
CN1 to CN8 2-way terminal block 5.08mm 8
Power connector 3-way terminal block 5.08mm 1
 Diodes D1 and D14 are shown as 1N4003. Any 1N400x series diode can be used here.

 S1 is a 6mm right angle tactile switch, Omron B3F series.


Rapid Electronics part # 78-0140
cheaper alternative is Rapid Electronics part # 78-1154

 IC1 is a 7805, 5 volt, 1 amp regulator IC.


For use in automotive applications, or where you need the circuit to operate from input voltages down to 6 volts
replace IC1 with an LM2940CT-5 and install a 47µF/10volt to C3
Rapid Electronics part # 82-0678 and part # 11-0815 or 11-1502

 STP36NF06L MOSFETs are logic-level N-channel devices. For use on this PCB maximum current per channel is 2
amps (do not exceed this). STP20NF06 can be used as an alternative.

Maximum current for the whole board should not exceed 16 amps.

 3-way and 2-way terminal blocks are 5.08mm pitch but a 5mm part will also fit.

 The PIC16F628A needs to be programmed with the correct firmware (see firmware section). If you bought the kit,
this code is already programmed into the supplied 16F628A.

 C1 is 5mm polyester box type

 C2/C4 are 2.5mm radial lead multilayer ceramic Y5V or X7R dielectric

 Resistors are all 1/4 watt, 5% carbon film type.

The LED current limit resistors R1-R8 are 330R. Don't use a lower value resistor for these as it will affect the output voltage
from the PIC I/O pin reducing the voltage at the MOSFET gate.

All components used in this kit can be sourced from Rapid Electronics
Standard parts are used in this project and should be easy to source from distributors world wide.

You might also like