Scribd
Upload
18 views2 pages

Fee Project I-I

The document proposes developing a laser light security system and automatic clap light system using Arduino Uno. It details the objectives, components, methodology, benefits, and conclusion of the two systems.

Uploaded by

poudelaayush47
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
18 views2 pages

Fee Project I-I

The document proposes developing a laser light security system and automatic clap light system using Arduino Uno. It details the objectives, components, methodology, benefits, and conclusion of the two systems.

Uploaded by

poudelaayush47
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

TRIBHUVAN UNIVERSITY

HIMALAYA COLLEGE OF ENGINEERING


ELECTRONICS PROJECT

Title: Proposal for Laser Light Security System and Automatic Clap Light with Arduino Uno

Introduction:
Security systems are becoming increasingly vital in various environments, ranging from homes to commercial
establishments. In this proposal, we outline a plan to develop a Laser Light Security System using Light
Dependent Resistors (LDR) and lasers, alongside an Automatic Clap Light system controlled by an Arduino
Uno microcontroller.

Objective:
The primary objective of this project is to design and implement two innovative systems:
1. Laser Light Security System: Utilizing lasers and LDRs to detect intrusions or unauthorized movements.
2. Automatic Clap Light: Triggering lights based on clapping sounds, offering hands-free control in domestic
settings.

Components Needed:
1. Arduino Uno microcontroller
2. Laser modules
3. Light Dependent Resistors (LDRs)
4. LEDs or buzzer for alarm (for the security system)
5. Sound sensor (for the clap light system)
6. Breadboard and jumper wires
7. Resistor as per requirements (2.2k)
8. Power source (battery or adapter)

Methodology:
1. Laser Light Security System:
- Setup: Place the laser module on one end of the area to be secured, and the LDRs on the other end.
- Circuit Design: Connect the LDR into the circuit to measure light intensity variations. When the laser
beam is interrupted (e.g., by an intruder), the light intensity at the LDR decreases or gets blocked, triggering
an alert. A significant decrease in light intensity is detected, activate an alarm (LEDs or buzzer) to indicate
intrusion.
2. Automatic Clap Light:
- Setup: Place the clap sensor in a suitable location where it can detect clapping sounds easily.
- Circuit Design: Connect the clap sensor to one of the digital pins of the Arduino Uno. When the sensor
detects a clap, it sends a signal to the Arduino.
- Programming: Write Arduino code to detect the signal from the clap sensor. Upon detection, toggle the
state of LEDs to turn them on or off, providing a hands-free lighting solution.
Benefits:
1. Enhanced Security: The Laser Light Security System offers a reliable means of detecting intrusions,
enhancing security in residential or commercial spaces.
2. Convenience: The Automatic Clap Light system provides hands-free control of lighting, improving
convenience and accessibility, especially for individuals with mobility impairments.
3. Cost-Effective: Utilizing Arduino Uno and simple electronic components, both systems can be developed at
a relatively low cost compared to commercial alternatives.
Conclusion:
The proposed Laser Light Security System and Automatic Clap Light system offer innovative solutions to
enhance security and convenience in various settings. By leveraging Arduino Uno and basic electronic
components, these systems can be developed affordably and effectively. This project aims to contribute to the
advancement of DIY security and automation technologies.
The Names of the students in the team are listed below: -

1.Debiyani Budha Magar


2.Aayush Poudel
3.Bhupendra Karki
4.Arpan Bhattrai
Approval:
We seek approval for the implementation of this project, along with the necessary resources and support for its
successful execution.
Thank you for considering our proposal. We are eager to begin working on this project and look forward to
your response.

Sincerely,
Aayush Poudel
Group Head

You might also like