ISCAR FACE GROOVINGLINES

Metric and Inch Catalog

PICCO CHAMGROOVE MINCUT HELIFACE DO-GRIP CUT-GRIP TANG-FACE SELF-GRIP PENTACUT

w w w . i s c a r. c o m
 FACE GROOVE-TURN
TABLE OF CONTENTS
TOOLS and INSERTS 9

PICCO................................................................................................................................... 10

CHAMGROOVE..................................................................................................................... 29

MINCUT................................................................................................................................. 31

HELIFACE.............................................................................................................................. 37

DO-GRIP................................................................................................................................ 76

CUT-GRIP (Long Pocket)........................................................................................................ 83

TANGFACE.......................................................................................................................... 109

SELF-GRIP.......................................................................................................................... 115

PENTA-CUT......................................................................................................................... 122

HOLDERS 131

PICCO HOLDERS.................................................................................................................. 23

TOOL BLOCKS.................................................................................................................... 132

CAMFIX................................................................................................................................ 137

HSK..................................................................................................................................... 146

IM........................................................................................................................................ 150

SQUARE SHANK HOLDERS.................................................................................... 51, 86, 153

USER GUIDE 161

INDEX 174

1
FACE GROOVE-TURN

Find The NEOLOGIQ

NEOLOGIQAL
AL Tool
For Your Application!
• The virtual tool advisor features advanced AI
and ‘Big Data’ analytics
• Supports complicated machining tasks and challenges
• Offers a wide range of functions and recommendations
to operate machining centers
• Features online service 24/7 in more than 30 languages
• Functions according to ISO 13399

w ww. is car . com

Learn More...
Download
ISCAR WORLD App Play Store App Store
2 ISCAR
 FACE GROOVE-TURN
A Variety of Inserts for Face Machining Applications

CW

CDX

XN
DA

Face Grooving DAXN 6–40 mm Face Grooving DAXN 24–80 mm

DAXN DAXX CWN CWX CDX Page DAXN DAXX CWN CWX CDX Page

PENTA 34F
PICCO

6 - 1 5 40 10 12 ∞ 2.39 4 5 122
MIFR/MEFL

GDMY/N
8 - 1.5 3.5 15 34-35 50 ∞ 8 8 27 95, 98
GFQR

GIF

12 19 1 2.5 3 30 80 ∞ 8 10 27 90-92
GIFG 8
HGPL

12 ∞ 3 6 ∞ 75 50 ∞ 8 8 25 89
GIMM 8CC
GRIP

12 ∞ 3 6.35 ∞ 70 80 ∞ 8 8 ∞ 107
GDMM CC
DGN

21 ∞ 4 6 ∞ 79-82 50 ∞ 7 8 ∞ 108
HFPR/L

GIA-K

12 ∞ 3 6 ∞ 68 80 ∞ 8 8 25 93
TNF

GFF

30 700 3 6 ∞ 111-112 25 55 2.1 6 35 121

HFPN

27 130 2 2 14 67

3
FACE GROOVE-TURN

Small Diameter Face Machining Systems

Tool: HGHR/L see page 39

B A Insert: GRIP… / HGPL…
CW = 3-6.35 mm
CDX = 6 mm
DAXN = 12 mm
Integral shank toolholder with
double-ended inserts.
Used for face grooving and face
turning of small parts for 12 mm
minimum groove diameter.

Tool: HGAER/L… (adapter) see page 52

B A Tool: HFAER/L… (adapter) see page 53
Insert: HFPR/L…
CW = 3-6 mm
CDX = 32 mm
DAXN = 12 mm
Exchangeable external adapters.
Used with HELIFACE and GRIP
inserts for deep face machining.

Tool: PCHPR/L see page 127

B A Insert: PENTA 34F...
CW = 2.39-4 mm
CDX = 5 mm
DAXN = 22 mm
Pentagonal insert for face
grooving and recessing up
to 5 mm depth of cut at a
minimum of 22 mm diameter.

Tool: PICCO R010 see pages 10-15

C B
CW = 1-5 mm
CDX = 6 mm
DAXN = 6 mm
Small solid carbide bars for
machining shallow grooves from
6 mm minimum diameter.

4 ISCAR
 FACE GROOVE-TURN
Tool: PICCO R015 see pages 21-22
B
CW = 2.5-3 mm
CDX = 30 mm
DAXN = 8 mm
Small solid carbide bars for
machining deep face grooves of up
to 30 and 8 mm minimum diameter.

Tool: MIFHR ... see page 31

C B Insert: MIFR …
CW = 1.5-3.5 mm
CDX = 5.5 mm
DAXN = 8 mm
MINCUT-A family of internal face
grooving and face turning tools
for machining small diameters
ranging from 8-60 mm.
Strong and stable tangential
pocket with internal coolant.

Tool: MGCH 09C see page 29

B C Insert: GFQR…
CW = 1-2.5 mm
CDX = 3 mm
DAXN = 12 mm
A screw-clamped insert on an
internal coolant solid carbide bar.
Used for machining shallow grooves
from 12 mm minimum diameter.

Main Applications
A B C

CW CW
CW

CDX CDX
CDX

N XN XN
X DA DA
DA
Grooving Next to a Shaft External Grooving Internal Grooving

5
FACE GROOVE-TURN

Medium Diameter Face Machining Systems

Tool: HFHR/L… see pages 40-46

B A
Insert: HFPR/L…
CW = 3-6 mm
CDX = 32 mm
DAXN = 25 mm
Integral shank toolholders
carrying HELIFACE and GRIP
inserts. For deep face grooving
and side face turning.

Tool: HFPAD… (adapter) see pages 48-50

B A
Insert: HFPR/L…
CW = 3-6 mm
CDX = 20 mm
DAXN = 25 mm
Slanted, screw-clamped adapter carrying
HELIFACE and GRIP inserts. A part
of the MODULAR-GRIP system. Very
rigid, for tough face operations.

Tool: TNFFH see page 109

B Insert: TNF 3-6C…
CW = 3-6 mm
CDX = 35 mm
DAXN = 30 mm
Adapter and blade toolholders
carrying TNF GN/M/P-IQ inserts.
For deep face grooving.

Tool: HFFR/L… see page 51 Tool: TNFFA see page 110

B Insert: HFPR/L… B A Insert: TNF GN/M/P-IQ...
CW = 4-6 mm CW = 3-6 mm
CDX = 38 mm CDX = 35 mm
DAXN = 48 mm DAXN = 30 mm
Economical, double-ended blades Reinforced blades carrying
carrying HELIFACE and GRIP TNF GN/M/P-IQ inserts.
inserts. Recommended for deep Recommended for face grooving
face grooving and face turning to only. Can machine along a shaft.
a maximum depth of 38 mm. Excellent chip evacuation.

6 ISCAR
 FACE GROOVE-TURN
Tool: PCHPRS/LS see page 130 Tool: HFHR/L..-M see page 54
B A Insert: PENTA 34F-RS/LS… B A Insert: HFPR/L…
CW = 2.39-4 mm CW = 3-6 mm
CDX = 5 mm CDX = 5.3 mm
DAXN = 22 mm DAXN = 20 mm
Pentagonal insert for face grooving Integral toolholders carrying
and recessing next to shoulders HELIFACE and GRIP inserts. For
up to 5 mm depth of cut at a machining up to 5.3 mm depth of
minimum of 22 mm diameter. cut. 3-6 mm wide inserts can be
mounted in the same pocket.

Tool: HFAIR/L…& HGAIR/L

B C (adapter) see pages 57, 60
Insert: HFPR/L…
CW = 3-6 mm
CDX = 12 mm
DAXN = 32 mm
Exchangeable, internal coolant
adapters carrying HELIFACE and
GRIP inserts. Recommended for
deep internal face machining.

Tool: HFIR/L..-MC see page 63

B C Insert: HFPR/L…
CW = 3-6 mm
CDX = 5 mm
DAXN = 20 mm
Boring bars for shallow face
machining of up to 5 mm
depth carrying HELIFACE and
GRIP inserts. Internal coolant.
3-6 mm width inserts can be
mounted in the same pocket.

Main Applications
A B C

CW CW
CW

CDX CDX CDX

XN XN XN
DA DA DA
Grooving Next to a Shaft External Grooving Internal Grooving

7
FACE GROOVE-TURN

Large Diameter Face Machining Systems

Tool: CGFG 51-..R/L-P8
B A see page 88
Insert: GIMY 8…
CW = 8 mm
CDX = 120 mm
DAXN = 180 mm
Blades carrying 8 mm single-ended
CUT-GRIP inserts. Can machine
up to 120 mm depth next to a
shaft. Used for large diameters.

Tool: GHFG ..R/L-8 see page 83

B A Insert: GDMY 8..
CW = 8 mm
CDX = 25 mm
DAXN = 50 mm
Integral toolholders carrying 8 mm
CUT-GRIP inserts. For heavy
machining of medium and large parts.
Can machine next to a shaft of up to
25 mm depth.

Tool: GAFG ..R/L-8

B A
(adapter) see page 87
Insert: GDMM 8CC
CW = 8 mm
CDX = 25 mm
DAXN = 80 mm
Exchangeable adapters carrying
8 mm CUT-GRIP inserts. Can
machine up to 25 mm depth next
to a shaft. For heavy machining
of medium and large parts.

Main Applications
A B C

CW CW
CW

CDX CDX
CDX

XN XN XN
DA DA DA

Grooving Next to a Shaft External Grooving Internal Grooving

8 ISCAR
 FACE GROOVE-TURN
TOOLS AND INSERTS

9
FACE GROOVE-TURN

PICCO
OAL
PICCO-010/610-N DAXN
(Face Grooving)
Inserts with Internal Coolant
Channel for Face Grooving a DCONMS
CW CDX
LU

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW CDX DCONMS a LU OAL (mm/rev)
PICCO R 010.1006-10N 6.0 1.00 1.50 6.05 5.20 9.0 32.00 • 0.01-0.04
PICCO R 010.1506-10N 6.0 1.50 2.00 6.05 5.20 9.0 32.00 • 0.01-0.04
PICCO R 010.1008-10N 8.0 1.00 1.50 7.05 5.90 9.0 32.00 • 0.01-0.04
PICCO R 010.1008-20N 8.0 1.00 1.50 7.05 5.90 19.0 41.00 • 0.01-0.04
PICCO R 010.1008-30N 8.0 1.00 1.50 7.05 5.90 29.0 51.00 • 0.01-0.04
PICCO R 610.1008-10N 8.0 1.00 1.50 6.05 5.20 9.0 32.00 • 0.01-0.04
PICCO R/L 010.1508-20N 8.0 1.50 2.50 7.05 5.90 19.0 41.00 • 0.01-0.04
PICCO R 010.1508-10N 8.0 1.50 2.50 7.05 5.90 9.0 32.00 • 0.01-0.04
PICCO R 010.1508-30N 8.0 1.50 2.50 7.05 5.90 29.0 51.00 • 0.01-0.04
PICCO R 610.1508-10N 8.0 1.50 2.50 6.05 5.20 9.0 32.00 • 0.01-0.04
PICCO R 610.1508-20N 8.0 1.50 2.50 6.05 5.20 19.0 41.00 • 0.01-0.04
PICCO R/L 010.2008-30N 8.0 2.00 3.00 7.05 5.90 29.0 51.00 • 0.02-0.05
PICCO R 010.2008-10N 8.0 2.00 3.00 7.05 5.90 9.0 32.00 • 0.02-0.05
PICCO R 010.2008-20N 8.0 2.00 3.00 7.05 5.90 19.0 41.00 • 0.02-0.05
PICCO R 610.2008-10N 8.0 2.00 3.00 6.05 5.20 9.0 32.00 • 0.02-0.05
PICCO R 610.2008-20N 8.0 2.00 3.00 6.05 5.20 19.0 41.00 • 0.02-0.05
PICCO R 010.2508-10N 8.0 2.50 3.50 7.05 5.90 9.0 32.00 • 0.02-0.05
PICCO R 010.2508-20N 8.0 2.50 3.50 7.05 5.90 19.0 41.00 • 0.02-0.05
PICCO R 610.2508-10N 8.0 2.50 3.50 6.05 5.20 9.0 32.00 • 0.02-0.05
PICCO R 010.3008-10N 8.0 3.00 3.50 7.05 5.90 9.0 32.00 • 0.02-0.06
PICCO R 010.3008-20N 8.0 3.00 3.50 7.05 5.90 19.0 41.00 • 0.02-0.06
PICCO R 010.3008-30N 8.0 3.00 3.50 7.05 5.90 29.0 51.00 • 0.02-0.06
PICCO R 610.3008-10N 8.0 3.00 3.50 6.05 5.20 9.0 32.00 • 0.02-0.06
PICCO R 610.3008-20N 8.0 3.00 3.50 6.05 5.20 19.0 41.00 • 0.02-0.06
• Only right-hand inserts are available as standard • All inserts are with sharp corners • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

10 ISCAR
 FACE GROOVE-TURN
OAL
PICCO-010/610-N DAXN
(Face Grooving)
Inserts with Internal Coolant
Channel for Face Grooving a DCONMS
CW CDX
LU

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW CDX DCONMS a LU OAL (IPR)
PICCO R 010.1006-10N .24 .039 .059 .238 .205 .354 1.260 • .0004-.0016
PICCO R 010.1506-10N .24 .059 .079 .238 .205 .354 1.260 • .0004-.0016
PICCO R 010.1008-10N .31 .039 .059 .278 .232 .354 1.260 • .0004-.0016
PICCO R 010.1008-20N .31 .039 .059 .278 .232 .748 1.614 • .0004-.0016
PICCO R 010.1008-30N .31 .039 .059 .278 .232 1.142 2.008 • .0004-.0016
PICCO R 610.1008-10N .31 .039 .059 .238 .205 .354 1.260 • .0004-.0016
PICCO R/L 010.1508-20N .31 .059 .098 .278 .232 .748 1.614 • .0004-.0016
PICCO R 010.1508-10N .31 .059 .098 .278 .232 .354 1.260 • .0004-.0016
PICCO R 010.1508-30N .31 .059 .098 .278 .232 1.142 2.008 • .0004-.0016
PICCO R 610.1508-10N .31 .059 .098 .238 .205 .354 1.260 • .0004-.0016
PICCO R 610.1508-20N .31 .059 .098 .238 .205 .748 1.614 • .0004-.0016
PICCO R/L 010.2008-30N .31 .079 .118 .278 .232 1.142 2.008 • .0008-.0020
PICCO R 010.2008-10N .31 .079 .118 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.2008-20N .31 .079 .118 .278 .232 .748 1.614 • .0008-.0020
PICCO R 610.2008-10N .31 .079 .118 .238 .205 .354 1.260 • .0008-.0020
PICCO R 610.2008-20N .31 .079 .118 .238 .205 .748 1.614 • .0008-.0020
PICCO R 010.2508-10N .31 .098 .138 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.2508-20N .31 .098 .138 .278 .232 .748 1.614 • .0008-.0020
PICCO R 610.2508-10N .31 .098 .138 .238 .205 .354 1.260 • .0008-.0020
PICCO R 010.3008-10N .31 .118 .138 .278 .232 .354 1.260 • .0008-.0024
PICCO R 010.3008-20N .31 .118 .138 .278 .232 .748 1.614 • .0008-.0024
PICCO R 010.3008-30N .31 .118 .138 .278 .232 1.142 2.008 • .0008-.0024
PICCO R 610.3008-10N .31 .118 .138 .238 .205 .354 1.260 • .0008-.0024
PICCO R 610.3008-20N .31 .118 .138 .238 .205 .748 1.614 • .0008-.0024
• Only right-hand inserts are available as standard • All inserts are with sharp corners • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

11
FACE GROOVE-TURN
OAL
PICCO-010/610 CDX
(Face Grooving) DCONMS
Inserts for Face Grooving DAXN CDX
CW a
OHN
CW
OHN
Right-hand shown

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC228
Designation DAXN(1) CW CDX DCONMS a OHN(2) OAL (mm/rev)
PICCO R 010.1006-10 6.0 1.00 1.50 6.00 5.20 11.0 26.00 • 0.01-0.04
PICCO R 010.1506-10 6.0 1.50 2.00 6.00 5.20 11.0 26.00 • 0.01-0.04
PICCO R 010.1008-10 8.0 1.00 1.50 7.00 5.90 11.0 26.00 • 0.01-0.04
PICCO R 010.1008-20 8.0 1.00 1.50 7.00 5.90 21.0 35.00 • 0.01-0.04
PICCO R 010.1008-30 8.0 1.00 1.50 7.00 5.90 30.0 45.00 • 0.01-0.04
PICCO R 610.1008-10 8.0 1.00 1.50 6.00 5.20 11.0 26.00 • 0.01-0.04
PICCO R 610.1008-20 8.0 1.00 1.50 6.00 5.20 20.0 35.00 • 0.01-0.04
PICCO R/L 010.1508-20 8.0 1.50 2.50 7.00 5.90 21.0 35.00 • 0.01-0.04
PICCO R/L 010.1508-30 8.0 1.50 2.50 7.00 5.90 30.0 45.00 • 0.01-0.04
PICCO R 010.1508-10 8.0 1.50 2.50 7.00 5.90 11.0 26.00 • 0.01-0.04
PICCO R 610.1508-10 8.0 1.50 2.50 6.00 5.20 11.0 26.00 • 0.01-0.04
PICCO R 610.1508-20 8.0 1.50 2.50 6.00 5.20 20.0 35.00 • 0.01-0.04
PICCO R/L 010.2008-30 8.0 2.00 3.00 7.00 5.90 30.0 45.00 • 0.02-0.05
PICCO R 010.2008-10 8.0 2.00 3.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.2008-20 8.0 2.00 3.00 7.00 5.90 21.0 35.00 • 0.02-0.05
PICCO R 610.2008-10 8.0 2.00 3.00 6.00 5.20 11.0 26.00 • 0.02-0.05
PICCO R 610.2008-20 8.0 2.00 3.00 6.00 5.20 20.0 35.00 • 0.02-0.05
PICCO R 010.2508-10 8.0 2.50 3.50 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.2508-20 8.0 2.50 3.50 7.00 5.90 21.0 35.00 • 0.02-0.05
PICCO R 010.2508-30 8.0 2.50 3.50 7.00 5.90 30.0 45.00 • 0.02-0.05
PICCO R 610.2508-10 8.0 2.50 3.50 6.00 5.20 11.0 26.00 • 0.02-0.05
PICCO R 610.2508-20 8.0 2.50 3.50 6.00 5.20 20.0 35.00 • 0.02-0.05
PICCO R 010.3008-10 8.0 3.00 3.50 7.00 5.90 11.0 26.00 • 0.02-0.06
PICCO R 010.3008-20 8.0 3.00 3.50 7.00 5.90 21.0 35.00 • 0.02-0.06
PICCO R 010.3008-30 8.0 3.00 3.50 7.00 5.90 30.0 45.00 • 0.02-0.06
PICCO R 610.3008-10 8.0 3.00 3.50 6.00 5.20 11.0 26.00 • 0.02-0.06
PICCO R 610.3008-20 8.0 3.00 3.50 6.00 5.20 20.0 35.00 • 0.02-0.06
• Only right-hand inserts are available as standard • All inserts are with sharp corners • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

12 ISCAR
 FACE GROOVE-TURN
OAL
PICCO-010/610 CDX
(Face Grooving) DCONMS
Inserts for Face Grooving DAXN CDX
CW a
OHN
CW
OHN
Right-hand shown

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC228
Designation DAXN(1) CW CDX DCONMS a OHN(2) OAL (IPR)
PICCO R 010.1006-10 .24 .039 .059 .236 .205 .433 1.024 • .0004-.0016
PICCO R 010.1506-10 .24 .059 .079 .236 .205 .433 1.024 • .0004-.0016
PICCO R 010.1008-10 .31 .039 .059 .276 .232 .433 1.024 • .0004-.0016
PICCO R 010.1008-20 .31 .039 .059 .276 .232 .827 1.378 • .0004-.0016
PICCO R 010.1008-30 .31 .039 .059 .276 .232 1.181 1.772 • .0004-.0016
PICCO R 610.1008-10 .31 .039 .059 .236 .205 .433 1.024 • .0004-.0016
PICCO R 610.1008-20 .31 .039 .059 .236 .205 .787 1.378 • .0004-.0016
PICCO R/L 010.1508-20 .31 .059 .098 .276 .232 .827 1.378 • .0004-.0016
PICCO R/L 010.1508-30 .31 .059 .098 .276 .232 1.181 1.772 • .0004-.0016
PICCO R 010.1508-10 .31 .059 .098 .276 .232 .433 1.024 • .0004-.0016
PICCO R 610.1508-10 .31 .059 .098 .236 .205 .433 1.024 • .0004-.0016
PICCO R 610.1508-20 .31 .059 .098 .236 .205 .787 1.378 • .0004-.0016
PICCO R/L 010.2008-30 .31 .079 .118 .276 .232 1.181 1.772 • .0008-.0020
PICCO R 010.2008-10 .31 .079 .118 .276 .232 .433 1.024 • .0008-.0020
PICCO R 010.2008-20 .31 .079 .118 .276 .232 .827 1.378 • .0008-.0020
PICCO R 610.2008-10 .31 .079 .118 .236 .205 .433 1.024 • .0008-.0020
PICCO R 610.2008-20 .31 .079 .118 .236 .205 .787 1.378 • .0008-.0020
PICCO R 010.2508-10 .31 .098 .138 .276 .232 .433 1.024 • .0008-.0020
PICCO R 010.2508-20 .31 .098 .138 .276 .232 .827 1.378 • .0008-.0020
PICCO R 010.2508-30 .31 .098 .138 .276 .232 1.181 1.772 • .0008-.0020
PICCO R 610.2508-10 .31 .098 .138 .236 .205 .433 1.024 • .0008-.0020
PICCO R 610.2508-20 .31 .098 .138 .236 .205 .787 1.378 • .0008-.0020
PICCO R 010.3008-10 .31 .118 .138 .276 .232 .433 1.024 • .0008-.0024
PICCO R 010.3008-20 .31 .118 .138 .276 .232 .827 1.378 • .0008-.0024
PICCO R 010.3008-30 .31 .118 .138 .276 .232 1.181 1.772 • .0008-.0024
PICCO R 610.3008-10 .31 .118 .138 .236 .205 .433 1.024 • .0008-.0024
PICCO R 610.3008-20 .31 .118 .138 .236 .205 .787 1.378 • .0008-.0024
• Only right-hand inserts are available as standard • All inserts are with sharp corners • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

13
FACE GROOVE-TURN
OAL
PICCO-010-N DAXN
(Full Radius for
Face Grooving)
Inserts with Internal
a DCONMS
Coolant Channel for Round
RE CDX
Profile Face Grooving CW LU

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW RE CDX DCONMS a LU OAL (mm/rev)
PICCO R 010.1005-10N 8.0 1.00 0.50 2.00 7.05 5.90 9.0 32.00 • 0.01-0.04
PICCO R 010.1005-20N 8.0 1.00 0.50 2.00 7.05 5.90 19.0 41.00 • 0.01-0.04
PICCO R 010.1608-10N 8.0 1.60 0.80 3.00 7.05 5.90 9.0 32.00 • 0.01-0.05
PICCO R 010.1608-20N 8.0 1.60 0.80 3.00 7.05 5.90 19.0 41.00 • 0.01-0.05
PICCO R 010.2010-10N 8.0 2.00 1.00 4.00 7.05 5.90 9.0 32.00 • 0.02-0.05
PICCO R 010.2010-20N 8.0 2.00 1.00 4.00 7.05 5.90 19.0 41.00 • 0.02-0.05
PICCO R 010.2512-10N 8.0 2.50 1.25 5.00 7.05 5.90 9.0 32.00 • 0.02-0.05
PICCO R 010.3015-10N 8.0 3.00 1.50 6.00 7.05 5.90 9.0 32.00 • 0.02-0.05
PICCO R 010.3015-20N 8.0 3.00 1.50 6.00 7.05 5.90 19.0 41.00 • 0.02-0.05

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW RE CDX DCONMS a LU OAL (IPR)
PICCO R 010.1005-10N .31 .039 .0197 .079 .278 .232 .354 1.260 • .0004-.0016
PICCO R 010.1005-20N .31 .039 .0197 .079 .278 .232 .748 1.614 • .0004-.0016
PICCO R 010.1608-10N .31 .063 .0315 .118 .278 .232 .354 1.260 • .0004-.0020
PICCO R 010.1608-20N .31 .063 .0315 .118 .278 .232 .748 1.614 • .0004-.0020
PICCO R 010.2010-10N .31 .079 .0394 .157 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.2010-20N .31 .079 .0394 .157 .278 .232 .748 1.614 • .0008-.0020
PICCO R 010.2512-10N .31 .098 .0492 .197 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.3015-10N .31 .118 .0590 .236 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.3015-20N .31 .118 .0590 .236 .278 .232 .748 1.614 • .0008-.0020
• Only right-hand inserts are available as standard, left-hand inserts on request • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

14 ISCAR
 FACE GROOVE-TURN
OAL
PICCO-010
(Round Face Groove) DCONMS
Inserts for Round Profile CDX
Face Grooving DAXN
a
CW
OHN Right-hand shown

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC1008
Designation DAXN(1) CW RE CDX DCONMS a OHN(2) OAL (mm/rev)
PICCO R 010.1005-10 8.0 1.00 0.50 2.00 7.00 5.90 11.0 26.00 • 0.01-0.04
PICCO R 010.1005-20 8.0 1.00 0.50 2.00 7.00 5.90 20.0 35.00 • 0.01-0.04
PICCO R 010.1608-10 8.0 1.60 0.80 3.00 7.00 5.90 11.0 26.00 • 0.01-0.05
PICCO R 010.1608-20 8.0 1.60 0.80 3.00 7.00 5.90 20.0 35.00 • 0.01-0.05
PICCO R 010.2010-10 8.0 2.00 1.00 4.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.2010-20 8.0 2.00 1.00 4.00 7.00 5.90 20.0 35.00 • 0.02-0.05
PICCO R 010.2512-10 8.0 2.50 1.25 5.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.2512-20 8.0 2.50 1.25 5.00 7.00 5.90 20.0 35.00 • 0.02-0.05
PICCO R 010.3015-10 8.0 3.00 1.50 6.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.3015-20 8.0 3.00 1.50 6.00 7.00 5.90 20.0 35.00 • 0.02-0.05

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC1008
Designation DAXN(1) CW RE CDX DCONMS a OHN(2) OAL (IPR)
PICCO R 010.1005-10 .31 .039 .0197 .079 .276 .232 .433 1.024 • .0004-.0016
PICCO R 010.1005-20 .31 .039 .0197 .079 .276 .232 .787 1.378 • .0004-.0016
PICCO R 010.1608-10 .31 .063 .0315 .118 .276 .232 .433 1.024 • .0004-.0020
PICCO R 010.1608-20 .31 .063 .0315 .118 .276 .232 .787 1.378 • .0004-.0020
PICCO R 010.2010-10 .31 .079 .0394 .157 .276 .232 .433 1.024 • .0008-.0020
PICCO R 010.2010-20 .31 .079 .0394 .157 .276 .232 .787 1.378 • .0008-.0020
PICCO R 010.2512-10 .31 .098 .0492 .197 .276 .232 .433 1.024 • .0008-.0020
PICCO R 010.2512-20 .31 .098 .0492 .197 .276 .232 .787 1.378 • .0008-.0020
PICCO R 010.3015-10 .31 .118 .0590 .236 .276 .232 .433 1.024 • .0008-.0020
PICCO R 010.3015-20 .31 .118 .0590 .236 .276 .232 .787 1.378 • .0008-.0020
• Only right-hand inserts are available as standard, left-hand inserts on request • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

15
FACE GROOVE-TURN
OAL
PICCO-620-N
(Face Grooving Along Shaft) DAXN
Inserts with Internal Coolant
Channel for Grooving Along a DCONMS
Shaft Dmin 6 mm
CDX
CW
LU

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW CDX DCONMS a LU OAL (mm/rev)
PICCO R 620.1006-20N 6.0 1.00 2.00 6.05 5.20 19.0 41.00 • 0.01-0.04
PICCO R 620.1506-20N 6.0 1.50 3.00 6.05 5.20 19.0 41.00 • 0.01-0.05
PICCO R 620.2006-20N 6.0 2.00 4.00 6.05 5.20 19.0 41.00 • 0.02-0.06
PICCO R 620.2506-20N 6.0 2.50 5.00 6.05 5.20 19.0 41.00 • 0.02-0.06
PICCO R 620.3006-20N 6.0 3.00 6.00 6.05 5.20 19.0 41.00 • 0.02-0.06
• Only right-hand inserts are available as standard, left-hand inserts on request • All carbide inserts are with sharp corners
• Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only • For detailed cutting data,see pages 162-164
(1) Minimum axial grooving diameter

OAL
PICCO-620-N
(Face Grooving Along Shaft) DAXN
Inserts with Internal Coolant
Channel for Grooving a DCONMS
Along Shaft Dmin .236"
CDX
CW
LU

I N C H
Recommended
Dimensions
Machining Data

IC908 f face-groove
Designation DAXN(1) CW CDX DCONMS a LU OAL (IPR)
PICCO R 620.1006-20N .24 .039 .079 .238 .205 .748 1.614 • .0004-.0016
PICCO R 620.1506-20N .24 .059 .118 .238 .205 .748 1.614 • .0004-.0020
PICCO R 620.2006-20N .24 .079 .157 .238 .205 .748 1.614 • .0008-.0024
PICCO R 620.2506-20N .24 .098 .197 .238 .205 .748 1.614 • .0008-.0024
PICCO R 620.3006-20N .24 .118 .236 .238 .205 .748 1.614 • .0008-.0024
• Only right-hand inserts are available as standard, left-hand inserts on request • All carbide inserts are with sharp corners
• Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only • For detailed cutting data,see pages 162-164
(1) Minimum axial grooving diameter

16 ISCAR
 FACE GROOVE-TURN
OAL
PICCO-620
(Groove Along Shaft) DCONMS
Inserts for Grooving Along CDX DAXN
a Shaft Dmin 6 mm
a
OHN
CW
Right-hand shown

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC1008
Designation DAXN(1) CW CDX DCONMS a OHN(2) OAL (mm/rev)
PICCO R 620.1006-20 6.0 1.00 2.00 6.00 5.20 20.0 35.00 • 0.01-0.04
PICCO R 620.1506-20 6.0 1.50 3.00 6.00 5.20 20.0 35.00 • 0.01-0.05
PICCO R 620.2006-20 6.0 2.00 4.00 6.00 5.20 20.0 35.00 • 0.02-0.06
PICCO R 620.2506-20 6.0 2.50 5.00 6.00 5.20 20.0 35.00 • 0.02-0.06
PICCO R 620.3006-20 6.0 3.00 6.00 6.00 5.20 20.0 35.00 • 0.02-0.06
• Only right-hand inserts are available as standard, left-hand inserts on request • All carbide inserts are with sharp corners
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

OAL
PICCO-620
(Groove Along Shaft) DCONMS
Inserts for Grooving Along CDX DAXN
a Shaft Dmin .236"
a
OHN
CW
Right-hand shown

I N C H
Recommended
Dimensions
Machining Data

IC1008 f face-groove
Designation DAXN(1) CW CDX DCONMS a OHN(2) OAL (IPR)
PICCO R 620.1006-20 .24 .039 .079 .236 .205 .787 1.378 • .0004-.0016
PICCO R 620.1506-20 .24 .059 .118 .236 .205 .787 1.378 • .0004-.0020
PICCO R 620.2006-20 .24 .079 .157 .236 .205 .787 1.378 • .0008-.0024
PICCO R 620.2506-20 .24 .098 .197 .236 .205 .787 1.378 • .0008-.0024
PICCO R 620.3006-20 .24 .118 .236 .236 .205 .787 1.378 • .0008-.0024
• Only right-hand inserts are available as standard, left-hand inserts on request • All carbide inserts are with sharp corners
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

17
FACE GROOVE-TURN
OAL
PICCO-016/020-N DAXN
(Face Grooving)
Inserts with Internal Coolant CDX
Channel for Deep Face Grooving a
Bar Max
CW DCONMS
LU
RE0.2

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW LU CDX DCONMS a OAL (mm/rev)
PICCO R016.0300-10N 16.0 3.00 9.00 9.00 8.00 5.50 32.00 • 0.01-0.05
PICCO R016.0300-20N 16.0 3.00 19.00 19.00 8.00 5.50 41.00 • 0.01-0.05
PICCO R016.0400-20N 16.0 4.00 19.00 19.00 8.00 6.00 41.00 • 0.01-0.05
PICCO R020.0300-25N 20.0 3.00 24.00 24.00 8.00 5.50 46.00 • 0.01-0.05
PICCO R020.0300-30N 20.0 3.00 29.00 29.00 8.00 5.50 51.00 • 0.01-0.04
PICCO R020.0300-40N 20.0 3.00 39.00 39.00 8.00 5.50 61.00 • 0.01-0.04
PICCO R020.0400-25N 20.0 4.00 24.00 24.00 8.00 6.00 46.00 • 0.01-0.06
PICCO R020.0400-30N 20.0 4.00 29.00 29.00 8.00 6.00 51.00 • 0.01-0.06
PICCO R020.0400-40N 20.0 4.00 39.00 39.00 8.00 6.00 61.00 • 0.01-0.05
PICCO R020.0500-25N 20.0 5.00 24.00 24.00 8.00 6.50 46.00 • 0.02-0.06
PICCO R020.0500-30N 20.0 5.00 29.00 29.00 8.00 6.50 51.00 • 0.02-0.06
PICCO R020.0500-35N 20.0 5.00 34.00 34.00 8.00 6.50 56.00 • 0.02-0.05
PICCO R020.0500-40N 20.0 5.00 39.00 39.00 8.00 6.50 61.00 • 0.02-0.05
• All inserts have two coolant holes which may be used with coolant pressure up to 100 bars • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

18 ISCAR
 FACE GROOVE-TURN
OAL
PICCO-016/020-N DAXN
(Face Grooving)
Inserts with Internal Coolant CDX
Channel for Deep Face Grooving a
PSI Max
CW DCONMS
LU
RE.008

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW LU CDX DCONMS a OAL (IPR)
PICCO R016.0300-10N .63 .118 .354 .354 .315 .217 1.260 • .0004-.0020
PICCO R016.0300-20N .63 .118 .748 .748 .315 .217 1.614 • .0004-.0020
PICCO R016.0400-20N .63 .157 .748 .748 .315 .236 1.614 • .0004-.0020
PICCO R020.0300-25N .79 .118 .945 .945 .315 .217 1.811 • .0004-.0020
PICCO R020.0300-30N .79 .118 1.142 1.142 .315 .217 2.008 • .0004-.0016
PICCO R020.0300-40N .79 .118 1.535 1.535 .315 .217 2.402 • .0004-.0016
PICCO R020.0400-25N .79 .157 .945 .945 .315 .236 1.811 • .0004-.0024
PICCO R020.0400-30N .79 .157 1.142 1.142 .315 .236 2.008 • .0004-.0024
PICCO R020.0400-40N .79 .157 1.535 1.535 .315 .236 2.402 • .0004-.0020
PICCO R020.0500-25N .79 .197 .945 .945 .315 .256 1.811 • .0008-.0024
PICCO R020.0500-30N .79 .197 1.142 1.142 .315 .256 2.008 • .0008-.0024
PICCO R020.0500-35N .79 .197 1.339 1.339 .315 .256 2.205 • .0008-.0020
PICCO R020.0500-40N .79 .197 1.535 1.535 .315 .256 2.402 • .0008-.0020
• All inserts have two coolant holes which may be used with coolant pressure up to 1450 PSI • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

19
FACE GROOVE-TURN
OAL 6.3
PICCO-016/020 OHN
Bar Max
(Face Grooving) DCONMS
Inserts with Coolant Holes
DAXN
for Deep Face Grooving RE0.2
a

CW RE0.2 Right-hand shown

M E T R I C
Recommended
Dimensions
Machining Data

IC1008
f face-groove
Designation DAXN(1) CW OHN(2) DCONMS a OAL (mm/rev)
PICCO R 016.0300-10 16.0 3.00 10.00 8.00 5.50 30.00 • 0.01-0.05
PICCO R 016.0300-20 16.0 3.00 20.00 8.00 5.50 40.00 • 0.01-0.05
PICCO R 016.0400-10 16.0 4.00 10.00 8.00 6.00 30.00 • 0.01-0.05
PICCO R 016.0400-20 16.0 4.00 20.00 8.00 6.00 40.00 • 0.01-0.05
PICCO R 020.0300-25 20.0 3.00 25.00 8.00 5.50 45.00 • 0.01-0.05
PICCO R 020.0300-30 20.0 3.00 30.00 8.00 5.50 50.00 • 0.01-0.04
PICCO R 020.0300-35 20.0 3.00 35.00 8.00 5.50 55.00 • 0.01-0.04
PICCO R 020.0300-40 20.0 3.00 40.00 8.00 5.50 60.00 • 0.01-0.04
PICCO R 020.0400-25 20.0 4.00 25.00 8.00 6.00 45.00 • 0.01-0.06
PICCO R 020.0400-30 20.0 4.00 30.00 8.00 6.00 50.00 • 0.01-0.06
PICCO R 020.0400-35 20.0 4.00 35.00 8.00 6.00 55.00 • 0.01-0.05
PICCO R 020.0400-40 20.0 4.00 40.00 8.00 6.00 60.00 • 0.01-0.05
PICCO R 020.0500-20 20.0 5.00 20.00 8.00 6.50 40.00 • 0.02-0.06
PICCO R 020.0500-25 20.0 5.00 25.00 8.00 6.50 45.00 • 0.02-0.06
PICCO R 020.0500-30 20.0 5.00 30.00 8.00 6.50 50.00 • 0.02-0.06
PICCO R 020.0500-35 20.0 5.00 35.00 8.00 6.50 55.00 • 0.02-0.05
PICCO R 020.0500-40 20.0 5.00 40.00 8.00 6.50 60.00 • 0.02-0.05
• All inserts have two coolant holes which may be used with coolant pressure up to 100 bars • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

OAL .248
PICCO-016/020 OHN
PSI Max
(Face Grooving) DCONMS
Inserts with Coolant Holes
DAXN
for Deep Face Grooving RE.008
a

CW RE.008 Right-hand shown

I N C H
Recommended
Dimensions
Machining Data
IC1008

f face-groove
Designation DAXN(1) CW OHN(2) DCONMS a OAL (IPR)
PICCO R 016.0300-10 .63 .118 .394 .315 .217 1.181 • .0004-.0020
PICCO R 016.0300-20 .63 .118 .787 .315 .217 1.575 • .0004-.0020
PICCO R 016.0400-10 .63 .157 .394 .315 .236 1.181 • .0004-.0020
PICCO R 016.0400-20 .63 .157 .787 .315 .236 1.575 • .0004-.0020
PICCO R 020.0300-25 .79 .118 .984 .315 .217 1.772 • .0004-.0020
PICCO R 020.0300-30 .79 .118 1.181 .315 .217 1.969 • .0004-.0020
PICCO R 020.0300-35 .79 .118 1.378 .315 .217 2.165 • .0004-.0020
PICCO R 020.0300-40 .79 .118 1.575 .315 .217 2.362 • .0004-.0020
PICCO R 020.0400-25 .79 .157 .984 .315 .236 1.772 • .0004-.0024
PICCO R 020.0400-30 .79 .157 1.181 .315 .236 1.969 • .0004-.0024
PICCO R 020.0400-35 .79 .157 1.378 .315 .236 2.165 • .0004-.0020
PICCO R 020.0400-40 .79 .157 1.575 .315 .236 2.362 • .0004-.0020
PICCO R 020.0500-20 .79 .197 .787 .315 .256 1.575 • .0010-.0024
PICCO R 020.0500-25 .79 .197 .984 .315 .256 1.772 • .0010-.0024
PICCO R 020.0500-30 .79 .197 1.181 .315 .256 1.969 • .0010-.0024
PICCO R 020.0500-35 .79 .197 1.378 .315 .256 2.165 • .0010-.0020
PICCO R 020.0500-40 .79 .197 1.575 .315 .256 2.362 • .0010-.0020
• All inserts have two coolant holes which may be used with coolant pressure up to 1450 PSI • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

20 ISCAR
 FACE GROOVE-TURN
OAL
PICCO-015-N DAXN
(Face Grooving)
Inserts with Internal Coolant CDX
Channel for Deep Face Grooving a
CW DCONMS
LU

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW LU DCONMS a OAL (mm/rev)
PICCO R 015.2515-20N 8.0 2.50 19.00 7.05 5.90 41.00 • 0.01-0.04
PICCO R 015.3015-20N 8.0 3.00 19.00 7.05 5.90 41.00 • 0.02-0.05
PICCO R 015.3015-30N 8.0 3.00 29.00 7.05 5.90 51.00 • 0.01-0.04

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation DAXN(1) CW LU DCONMS a OAL (IPR)
PICCO R 015.2515-20N .31 .098 .7480 .278 .232 1.614 • .0004-.0016
PICCO R 015.3015-20N .31 .118 .7480 .278 .232 1.614 • .0008-.0020
PICCO R 015.3015-30N .31 .118 1.1417 .278 .232 2.008 • .0004-.0016
• Only right-hand inserts are available as standard, left-hand inserts on request • All inserts are with sharp corners
• Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

21
FACE GROOVE-TURN
OAL
PICCO-015 (Face Grooving) CDX
DCONMS
Inserts for Deep Face Grooving
DAXN

a CW
CW OHN
Right-hand shown

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC228
Designation DAXN(1) CW OHN(2) DCONMS a OAL CDX (mm/rev)
PICCO R 015.2515-20 8.0 2.50 20.00 7.00 5.90 35.00 20.00 • 0.01-0.04
PICCO R/L 015.3015-20 8.0 3.00 20.00 7.00 5.90 35.00 20.00 • 0.02-0.05
PICCO R 015.3015-30 8.0 3.00 30.00 7.00 5.90 45.00 30.00 • 0.01-0.04

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC228
Designation DAXN(1) CW OHN(2) DCONMS a OAL CDX (IPR)
PICCO R 015.2515-20 .31 .098 .787 .276 .232 1.378 .787 • .0004-.0016
PICCO R/L 015.3015-20 .31 .118 .787 .276 .232 1.378 .787 • .0008-.0020
PICCO R 015.3015-30 .31 .118 1.181 .276 .232 1.772 1.181 • .0004-.0016
• Only right-hand inserts are available as standard, left-hand inserts on request • All inserts are with sharp corners
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

22 ISCAR
 FACE GROOVE-TURN
LH LSCMS CND

PICMU DCONNWS h6
Holders with Improved Cooling DCONXWS h6
SPL* (mini bar insert dia.)
Supply Suitable for Mounting LSCWS
PICCO-CUT, PICCO-JET Inserts OAL
and PICCO-INDEX Tools.
DCONMS g7
H * To be used only when mounting PICCO-CUT insert types

M E T R I C
Designation DCONMS DCONNWS(1) DCONXWS(2) OAL LH LSCMS H LSCWS CND SPL(3)
PICMU 12-4 12.00 4.00 4.05 85.00 19.7 45.60 11.0 19.00 5.00 6.00
PICMU 12-5 12.00 5.00 5.05 85.00 19.7 45.60 11.0 20.50 6.00 6.00
PICMU 16-4 16.00 4.00 4.05 85.00 19.7 45.60 14.0 19.00 5.00 6.00
PICMU 16-5 16.00 5.00 5.05 85.00 19.7 45.60 14.0 20.50 6.00 6.00
PICMU 16-6 16.00 6.00 6.05 85.00 19.7 45.60 14.0 20.50 6.00 6.00
PICMU 16-7 16.00 7.00 7.05 85.00 19.7 45.60 14.0 20.80 8.00 7.00
PICMU 20-4 20.00 4.00 4.05 85.00 19.7 45.60 18.0 19.00 5.00 6.00
PICMU 20-5 20.00 5.00 5.05 85.00 19.7 45.60 18.0 20.50 6.00 6.00
PICMU 20-6 20.00 6.00 6.05 85.00 19.7 45.60 18.0 20.50 6.00 6.00
PICMU 20-7 20.00 7.00 7.05 85.00 19.7 45.60 18.0 20.80 8.00 7.00
PICMU 20-8 20.00 8.00 8.00 85.00 19.7 45.60 18.0 20.00 8.00 -
PICMU 22-4 22.00 4.00 4.05 85.00 19.7 45.60 20.0 19.00 5.00 6.00
PICMU 22-5 22.00 5.00 5.05 85.00 19.7 45.60 20.0 20.50 6.00 6.00
PICMU 22-6 22.00 6.00 6.05 85.00 19.7 45.60 20.0 20.50 6.00 6.00
PICMU 22-7 22.00 7.00 7.05 85.00 19.7 45.60 20.0 20.80 8.00 7.00

I N C H
Designation DCONMS DCONNWS(1) DCONXWS(2) OAL LH LSCMS H LSCWS CND SPL(3)
PICMU 12.7-4 .500 .158 .160 3.346 .776 1.795 .433 .7480 .197 .2363
PICMU 12.7-5 .500 .197 .199 3.346 .776 1.795 .433 .8070 .236 .2363
PICMU 15.9-4 .625 .158 .160 3.346 .776 1.795 .551 .7480 .197 .2363
PICMU 15.9-5 .625 .197 .199 3.346 .776 1.795 .551 .8070 .236 .2363
PICMU 15.9-6 .625 .236 .238 3.346 .776 1.795 .551 .8070 .236 .2363
PICMU 15.9-7 .625 .276 .278 3.346 .776 1.795 .551 .8190 .315 .2756
PICMU 19-4 .750 .158 .160 3.346 .776 1.795 .709 .7480 .197 .2363
PICMU 19-5 .750 .197 .199 3.346 .776 1.795 .709 .8070 .236 .2363
PICMU 19-6 .750 .236 .238 3.346 .776 1.795 .709 .8070 .236 .2363
PICMU 19-7 .750 .276 .278 3.346 .776 1.795 .709 .8190 .315 .2756
PICMU 25.4-4 1.000 .158 .160 3.346 .776 1.795 .787 .7480 .197 .2363
PICMU 25.4-5 1.000 .197 .199 3.346 .776 1.795 .787 .8070 .236 .2363
PICMU 25.4-6 1.000 .236 .238 3.346 .776 1.795 .787 .8070 .236 .2363
PICMU 25.4-7 1.000 .276 .278 3.346 .776 1.795 .787 .8190 .315 .2756
• Holders are suitable for right- and left-hand inserts, and boring bars
(1) Minimum diameter
(2) Maximum diameter
(3) Spacer length

Spare Parts
All PICCO.... style
Designation
except PICCO .....N
PICMU 12-4 SPACER D3.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 12-5 SPACER D4.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 16-4 SPACER D3.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 16-5 SPACER D4.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 16-6 SPACER D5.7X6 SR M6X0.5X6 PF HW 3.0 PL 16 M6-D5
PICMU 16-7 SPACER D6.7X7 SR M6X0.5X6 PF HW 3.0 PL 16 M6-D5
PICMU 20-4 SPACER D3.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5 Screw
PICMU 20-5 SPACER D4.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 20-6 SPACER D5.7X6 SR M6X0.5X6 PF HW 3.0 PL 16 M6-D5
PICMU 20-7 SPACER D6.7X7 SR M6X0.5X6 PF HW 3.0 PL 16 M6-D5
PICMU 20-8 SR M8X0.5X6.5-PF HW 4.0 PL 16 M6-D5
PICMU 22-4 SPACER D3.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 22-5 SPACER D4.7X6 SR M5X0.5X6-PF HW 2.5 PL 16 M6-D5
PICMU 22-6 SPACER D5.7X6 SR M6X0.5X6 PF HW 3.0 PL 16 M6-D5
PICMU 22-7 SPACER D6.7X7 SR M6X0.5X6 PF HW 3.0 PL 16 M6-D5
PICCO .....N style

23
FACE GROOVE-TURN
OAL
PICCO ACE-N
H DCONMS
Holders for PICCO-JET Inserts
with Internal Coolant Channels LB
DCONWS LSCMS

1/8"

M E T R I C
Designation DCONMS DCONWS OAL LSCMS LB H
PICCO ACE 16-4N 16.00 4.05 115.00 68.00 90.00 14.0
PICCO ACE 16-5N 16.00 5.05 115.00 68.00 90.00 14.0
PICCO ACE 16-6N 16.00 6.05 115.00 68.00 90.00 14.0
PICCO ACE 16-7N 16.00 7.05 115.00 68.00 90.00 14.0
PICCO ACE 20-4N 20.00 4.05 115.00 68.00 90.00 18.0
PICCO ACE 20-5N 20.00 5.05 115.00 68.00 90.00 18.0
PICCO ACE 20-6N 20.00 6.05 115.00 68.00 90.00 18.0
PICCO ACE 20-7N 20.00 7.05 115.00 68.00 90.00 18.0
PICCO ACE 22-4N 22.00 4.05 115.00 68.00 90.00 20.0
PICCO ACE 22-6N 22.00 6.05 115.00 68.00 90.00 20.0
PICCO ACE 25-4N 25.00 4.05 115.00 68.00 90.00 23.0
PICCO ACE 25-5N 25.00 5.05 115.00 68.00 90.00 23.0
PICCO ACE 25-6N 25.00 6.05 115.00 68.00 90.00 23.0
PICCO ACE 25-7N 25.00 7.05 115.00 68.00 90.00 23.0
• Holders are suitable for right and left-hand PICCO...-N type solid tools only

Spare Parts

Designation
PICCO ACE 16-4N UM600H.K UM600H.M4 PIN 2X10 DIN6325
PICCO ACE 16-5N UM600H.K UM600H.M5 PIN 2X10 DIN6325
PICCO ACE 16-6N UM600H.K UM600H.M6 ZAD 2X12 DIN 6325 m6
PICCO ACE 16-7N UM600H.K UM600H.M7 ZAD 2X12 DIN 6325 m6
PICCO ACE 20-4N UM600H.K UM600H.M4 PIN 2X10 DIN6325
PICCO ACE 20-5N UM600H.K UM600H.M5 PIN 2X10 DIN6325
PICCO ACE 20-6N UM600H.K UM600H.M6 ZAD 2X12 DIN 6325 m6
PICCO ACE 20-7N UM600H.K UM600H.M7 ZAD 2X12 DIN 6325 m6
PICCO ACE 22-4N UM600H.K UM600H.M4 PIN 2X10 DIN6325
PICCO ACE 22-6N UM600H.K UM600H.M6 ZAD 2X12 DIN 6325 m6
PICCO ACE 25-4N UM600H.K UM600H.M4 PIN 2X10 DIN6325
PICCO ACE 25-5N UM600H.K UM600H.M5 PIN 2X10 DIN6325
PICCO ACE 25-6N UM600H.K UM600H.M6 ZAD 2X12 DIN 6325 m6
PICCO ACE 25-7N UM600H.K UM600H.M7 ZAD 2X12 DIN 6325 m6

OAL
PICCO ACE-N
DCONMS
Holders for PICCO-JET Inserts
with Internal Coolant Channels LB .157
DCONWS LSCMS

1/8"

I N C H
Designation DCONMS DCONWS OAL LSCMS LB
PICCO ACE 15.9-7N .625 .278 4.528 2.520 3.543
PICCO ACE 19-4N .750 .159 4.528 2.520 3.543
PICCO ACE 19-5N .750 .199 4.528 2.520 3.543
PICCO ACE 19-6N .750 .238 4.528 2.520 3.543
PICCO ACE 19-7N .750 .278 4.528 2.520 3.543
PICCO ACE 25.4-6N 1.000 .238 4.528 2.520 3.543
PICCO ACE 25.4-7N 1.000 .278 4.528 2.520 3.543
• Holders are suitable for right and left-hand PICCO...-N type solid tools only
Spare Parts

Designation
PICCO ACE 15.9-7N UM600H.K UM600H.M7 ZAD 2X12 DIN 6325 m6
PICCO ACE 19-4N UM600H.K UM600H.M4 PIN 2X10 DIN6325
PICCO ACE 19-5N UM600H.K UM600H.M5 PIN 2X10 DIN6325
PICCO ACE 19-6N UM600H.K UM600H.M6 ZAD 2X12 DIN 6325 m6
PICCO ACE 19-7N UM600H.K UM600H.M7 ZAD 2X12 DIN 6325 m6
PICCO ACE 25.4-6N UM600H.K UM600H.M6 ZAD 2X12 DIN 6325 m6
PICCO ACE 25.4-7N UM600H.K UM600H.M7 ZAD 2X12 DIN 6325 m6

24 ISCAR
 FACE GROOVE-TURN
OAL

PICCO-N (Holder) DCONMS

Holders for PICCO-JET Inserts
with Internal Coolant Channels
20 LSCMS DCONWS_2
H DCONWS

M E T R I C

Designation DCONMS DCONWS DCONWS_2 OAL LSCMS H

PICCO 16-4-5N 16.00 4.05 5.05 85.00 45.00 14.0 SR M5X0.5X6 T10
PICCO 20-4-5N 20.00 4.05 5.05 100.00 60.00 18.0 SR M5X0.5X8 T10
PICCO 22-4-5N 22.00 4.05 5.05 100.00 60.00 20.0 SR M5X0.5X8 T10
PICCO 16-6-7N 16.00 6.05 7.05 85.00 45.00 14.0 SR M5X0.5X6 T10
PICCO 16-6-8N 16.00 6.05 8.00 85.00 45.00 14.0 SR M5X0.5X6 T10
PICCO 20-6-7N 20.00 6.05 7.05 100.00 60.00 18.0 SR M5X0.5X8 T10
PICCO 20-6-8N 20.00 6.05 8.00 100.00 60.00 18.0 SR M5X0.5X8 T10
PICCO 22-6-7N 22.00 6.05 7.05 100.00 60.00 20.0 SR M5X0.5X8 T10
• Holders are suitable for right- and left-hand inserts, and boring bars

OAL

PICCO-N (Holder) DCONMS

Holders for PICCO-JET Inserts
with Internal Coolant Channels
.787 LSCMS DCONWS_2
H DCONWS

I N C H

Designation DCONMS DCONWS DCONWS_2 OAL LSCMS H

PICCO 19-4-5N .750 .159 .199 3.937 2.362 .677 SR M5X0.5X6 T10
PICCO 25.4-4-5N 1.000 .159 .199 4.134 2.559 .921 SR M5X0.5X10 T10
PICCO 16-6-8N .630 .238 .315 3.346 1.772 .551 SR M5X0.5X6 T10
PICCO 19-6-7N .750 .238 .278 3.937 2.362 .677 SR M5X0.5X6 T10
PICCO 20-6-8N .787 .238 .315 3.937 2.362 .709 SR M5X0.5X8 T10
PICCO 25.4-6-7N 1.000 .238 .278 4.134 2.559 .921 SR M5X0.5X10 T10
• Holders are suitable for left- and right-hand inserts, and boring bars

25
FACE GROOVE-TURN
LH LSCMS LH LSCMS
PICCO/MG PCO (Holder) 1 2
Holders for PICCO-CUT Inserts
H H
and Small Diameter Boring Bars
BD DCONMS
DCONWS_2 DCONMS
OAL OAL
DCONWS DCONWS

M E T R I C

Designation DCONMS DCONWS DCONWS_2 OAL LH LSCMS H BD Fig.

PICCO 12-4-5 12.00 4.00 5.00 75.00 10.00 55.00 10.3 - 2 SR M5X4-PF HW 2.5
PICCO 16-4-5 16.00 4.00 5.00 75.00 10.00 55.00 14.0 - 2 SR M5X6-PF HW 2.5
PICCO 20-4-5 20.00 4.00 5.00 90.00 10.00 70.00 18.0 - 2 SR M5X6-PF HW 2.5
PICCO 22-4-5 (1) 22.00 4.00 5.00 90.00 10.00 70.00 20.0 - 2 SR M5X6-PF HW 2.5
PICCO 16-6-7 16.00 6.00 7.00 75.00 10.00 55.00 14.0 - 2 SR M5X6-PF HW 2.5
PICCO 20-6-7 20.00 6.00 7.00 90.00 10.00 70.00 18.0 - 2 SR M5X6-PF HW 2.5
PICCO 22-6-7 (1) 22.00 6.00 7.00 90.00 10.00 70.00 20.0 - 2 SR M5X6-PF HW 2.5
MG PCO-12-6 12.00 6.00 - 75.00 15.00 50.80 11.0 18.00 1 SR M5X6-PF HW 2.5
MG PCO-16-6-8 16.00 6.00 8.00 75.00 10.00 55.00 14.0 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-20-6-8 20.00 6.00 8.00 90.00 10.00 70.00 18.0 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-22-6-8 (1) 22.00 6.00 8.00 90.00 10.00 70.00 20.0 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-25-6-8 25.00 6.00 8.00 90.00 10.00 70.00 23.0 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-16-9 16.00 9.00 - 75.00 15.00 53.00 15.0 20.00 1 SR M5X6-PF HW 2.5 PL 16

I N C H

Designation DCONMS DCONWS DCONWS_2 OAL LH LSCMS H BD Fig.

PICCO 12.7-4-5 .500 .157 .197 2.950 .394 2.170 .410 - 2 SR M5X4-PF HW 2.5
PICCO 15.9-4-5 .625 .157 .197 2.950 .394 2.170 .550 - 2 SR M5X6-PF HW 2.5
PICCO 19-4-5 .750 .157 .197 3.540 .394 2.760 .710 - 2 SR M5X6-PF HW 2.5
PICCO 25.4-4-5 (1) 1.000 .157 .197 3.543 .394 2.756 .921 - 2 SR M5X6-PF HW 2.5
PICCO 15.9-6-7 .625 .236 .276 2.950 .394 2.170 .550 - 2 SR M5X6-PF HW 2.5
PICCO 19-6-7 .750 .236 .276 3.540 .394 2.760 .710 - 2 SR M5X6-PF HW 2.5
PICCO 25.4-6-7 (1) 1.000 .236 .276 3.543 .394 2.756 .921 - 2 SR M5X6-PF HW 2.5
MG PCO-12.7-6 .500 .236 - 3.000 .590 2.090 .460 .709 1 SR M5X6-PF HW 2.5
MG PCO-15.9-6-8 .625 .236 .315 3.000 .390 2.170 .551 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-19-6-8 .750 .236 .315 3.500 .390 2.760 .709 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-25.4-6-8 (1) 1.000 .236 .315 3.543 .394 2.756 .921 - 2 SR M5X6-PF HW 2.5 MG PCO-SPCR8
MG PCO-16-9 .630 .354 - 2.953 .591 2.087 .591 .787 1 SR M5X6-PF HW 2.5 PL 16
• Holders are suitable for right- and left-hand inserts, and boring bars
(1) Tools for Swiss-type CNC

MG PCO...-6-8
PICCO...MF...8-...
PICCO...MFT...8-... Back Stopper
MG PCO-SPCR8

26 ISCAR
 FACE GROOVE-TURN
A A
PICCO ACE
Holders for PICCO-CUT Inserts BD DCONWS DCONMS H

LH LSCMS
OAL

M E T R I C

Designation DCONMS DCONWS BD OAL LH LSCMS H

PICCO ACE 12-4 12.00 4.00 14.50 85.00 23.00 53.00 10.3 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 12-5 12.00 5.00 14.50 85.00 23.00 53.00 10.3 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 16-4 16.00 4.00 14.50 85.00 21.50 53.50 14.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 16-5 16.00 5.00 14.50 85.00 21.50 53.00 14.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 16-6 16.00 6.00 19.90 85.00 23.00 53.50 14.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 16-7 16.00 7.00 19.90 85.00 23.00 53.50 14.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 20-4 20.00 4.00 14.50 150.00 21.50 118.00 18.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 20-5 20.00 5.00 14.50 150.00 21.50 118.00 18.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 20-6 20.00 6.00 19.90 150.00 21.50 118.00 18.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 20-7 20.00 7.00 19.90 150.00 21.50 118.00 18.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 22-4 22.00 4.00 14.50 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 22-5 22.00 5.00 14.50 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 22-6 22.00 6.00 19.90 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 22-7 22.00 7.00 19.90 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 25-4 25.00 4.00 14.50 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 25-5 25.00 5.00 14.50 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 25-6 25.00 6.00 19.90 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 25-7 25.00 7.00 19.90 150.00 21.50 118.00 20.0 PL 16 M6-D5 WRENCH ACE 6-7

I N C H

Designation DCONMS DCONWS BD OAL LH LSCMS H

PICCO ACE 12.7-4 .500 .157 .571 3.346 .906 2.087 .457 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 12.7-5 .500 .197 .571 3.346 .906 2.087 .457 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 15.9-4 .625 .157 .571 3.346 .846 2.087 .551 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 15.9-5 .625 .197 .571 3.346 .846 2.087 .551 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 15.9-6 .625 .236 .783 3.346 .906 2.087 .551 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 15.9-7 .625 .276 .783 3.346 .906 2.087 .551 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 19-4 .750 .157 .571 5.906 .846 4.646 .677 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 19-5 .750 .197 .571 5.906 .846 4.646 .677 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 19-6 .750 .236 .783 5.906 .906 4.646 .677 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 19-7 .750 .276 .783 5.906 .906 4.646 .677 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 25.4-4 1.000 .157 .571 5.906 .846 4.646 .905 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 25.4-5 1.000 .197 .571 5.906 .846 4.646 .905 PL 16 M6-D5 WRENCH ACE 4-5
PICCO ACE 25.4-6 1.000 .236 .783 5.906 .846 4.646 .905 PL 16 M6-D5 WRENCH ACE 6-7
PICCO ACE 25.4-7 1.000 .276 .783 5.906 .846 4.646 .905 PL 16 M6-D5 WRENCH ACE 6-7
• Holders are suitable for right- and left-hand PICCO inserts

Pins Body
Locking
shim Locking
shim Insert

Cap Pin
Cap

Wrench

27
FACE GROOVE-TURN
D1max OAL
L5 Cutting Edge Height
70
GHPCOR Clamp OAH
Perpendicular Square-Shank DCONNWS-DCONXWS H
Tools for Use on Cross HBH
Slide Units of Swiss-Type
OAW fmax B
and Automatic Machines
OHX
Right-hand shown

M E T R I C
Designation H B OAL L5 HBH OAH OAW D1 max OHX(1) fmax DCONNWS(2) DCONXWS(3)
GHPCOR 08-16-4-5 8.0 8.0 102.00 88.00 4.0 15.0 34.00 26.0 16.00 30.0 4.00 5.00
GHPCOR 10-16-4-5 10.0 10.0 102.00 88.00 2.0 18.0 34.00 26.0 16.00 30.0 4.00 5.00
GHPCOR 12-16-4-6 12.0 12.0 102.00 88.00 - 18.0 34.00 26.0 16.00 30.0 4.00 6.00
GHPCOR 12-25-4-6 12.0 12.0 102.00 88.00 - 18.0 43.00 26.0 25.00 39.0 4.00 6.00
GHPCOR 16-16-4-6 16.0 16.0 112.00 98.00 - 22.0 35.00 36.0 16.00 31.0 4.00 6.00
GHPCOR 16-25-4-6 16.0 16.0 112.00 98.00 - 22.0 44.00 36.0 25.00 40.0 4.00 6.00
GHPCOR 16-30-7-8 16.0 16.0 116.00 98.00 - 22.0 49.00 36.0 30.00 45.0 7.00 8.00
• PICCOCUT insert should not exceed OAW • Left-hand holders are available upon request • Coolant tube adapter: KQ2L06-M5 (for 6 mm coolant tube)
(1) Maximum overhang
(2) Minimum diameter
(3) Maximum diameter

Indexing from the top Indexing from the front

Spare Parts

Designation
GHPCOR 08-16-4-5 HED 08 SR M4X14 DIN912 HW 3.0 KQ2L06-M5
GHPCOR 10-16-4-5 HED 10 SR M4X14 DIN912 HW 3.0 KQ2L06-M5
GHPCOR 12-16-4-6 HED 12 SR M4X14 DIN912 HW 3.0 KQ2L06-M5
GHPCOR 12-25-4-6 HED 12 SR M4X14 DIN912 HW 3.0 KQ2L06-M5
GHPCOR 16-16-4-6 HED 16-4-6 SR M4X14 DIN912 HW 3.0 KQ2L06-M5
GHPCOR 16-25-4-6 HED 16-4-6 SR M4X14 DIN912 HW 3.0 KQ2L06-M5
GHPCOR 16-30-7-8 HED 16-7-8 SR M4X14 DIN912 HW 3.0

KITS

KIT PICCO Face

Contains One Toolholder
and a Set of Solid Carbide DAXN
Miniature Face Turning and
Grooving Boring Bars CWN-CWX

M E T R I C
Designation DAXN(1) CWN(2) CWX(3)
KIT PICCO SET-4R 8.0 1.00 3.00
(1) Minimum axial grooving diameter
(2) Minimum cutting width
(3) Maximum cutting width

PICCO
Face Grooving PICCO Mini-Bar Tool Set - 4R

Mini Bore
Designation Dia. OHN CDX CW Pcs. Designation CDX
PICCO 16.D6 1x Holder
Min Bore
PICCO R/L 010.1008-10 8.0 11 1.5 1.0 1x Mini Carbide Bar Dia.
PICCO R/L 010.1508-10 8.0 11 2.5 1.5 1x Mini Carbide Bar
CW
PICCO R/L 010.2008-10 8.0 11 3.0 2.0 1x Mini Carbide Bar OHN
PICCO R/L 010.2508-20 8.0 21 3.5 2.5 1x Mini Carbide Bar
PICCO R/L 010.3008-20 8.0 21 3.5 3.0 1x Mini Carbide Bar
Available grade: IC228

28 ISCAR
 FACE GROOVE-TURN
CHAMGROOVE
OHX
MGCH-C (face)
Face Machining Tools Carrying
GFQR Inserts for MGCH 09C DCONMS
(MG PCO-16-9)
Dmin 12 - Dmax 19 mm
Penetration Range WF
OAL The same tool applies for right-and left-machining

M E T R I C

Designation DCONMS OAL OHX(1) WF

MGCH 09C 9.00 83.50 65.0 5.50 SR 76-2145 T-15/5
Maximum overhang
(1)

For inserts, see pages: GFQR (30)

For holders, see pages: PICCO/MG PCO (Holder) (26)

MG PCO 75
Holder Bar for Adjustable Shank 15

16

MG PCO-16-9

OHX
MGCH-C (face)
Face Machining Tools Carrying
GFQR Inserts for Dmin .472 - MGCH 09C DCONMS
(MG PCO-16-9)
Dmax .748" Penetration Range
WF
OAL The same tool applies for right- and left-machining

I N C H

Designation DCONMS OAL OHX(1) WF

MGCH 09C .354 3.287 2.559 .217 SR 76-2145 T-15/5
Maximum overhang
(1)

For inserts, see pages: GFQR (30)

For holders, see pages: PICCO/MG PCO (Holder) (26)

MG PCO
Holder Bar for Adjustable Shank 2.953
.590

.630

MG PCO-16-9

29
FACE GROOVE-TURN

GFQR INSL
Face Grooving Inserts CDX
5
DAXN-DAXX

WF

CW RE .

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC528
Designation CW RE CWTOL(1) RETOL(2) CDX DAXN(3) DAXX(4) (mm/rev)
GFQR 12-1.00-0.05 1.00 0.05 0.02 0.030 1.50 12.0 16.0 • 0.01-0.04
GFQR 12-1.50-0.20 1.50 0.20 0.02 0.030 2.50 12.0 17.0 • 0.01-0.04
GFQR 12-2.00-0.20 2.00 0.20 0.02 0.030 3.00 12.4 18.0 • 0.02-0.05
GFQR 12-2.50-0.20 2.50 0.20 0.02 0.030 3.00 13.0 19.0 • 0.02-0.05
• For detailed cutting data, see pages 162-164
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum penetration diameter
(4) Maximum penetration diameter

GFQR INSL
Face Grooving Inserts CDX .197
DAXN-DAXX

WF

CW RE

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC528
Designation CW RE CWTOL(1) RETOL(2) CDX DAXN(3) DAXX(4) (IPR)
GFQR 12-1.00-0.05 .039 .0020 .0008 .0012 .059 .47 .63 • .0004-.0016
GFQR 12-1.50-0.20 .059 .0079 .0008 .0012 .098 .47 .67 • .0004-.0016
GFQR 12-2.00-0.20 .079 .0079 .0008 .0012 .118 .49 .71 • .0008-.0020
GFQR 12-2.50-0.20 .098 .0079 .0008 .0012 .118 .51 .75 • .0008-.0020
• For detailed cutting data, see pages 162-164
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum penetration diameter
(4) Maximum penetration diameter

30 ISCAR
 FACE GROOVE-TURN
MINCUT
MIFHR... 10 MIFHR... 8 RADW
MIFHR
Bars for Face and Internal
CND DCONMS
Grooving, Undercutting
and Threading Inserts RE RE
L3
LH WF
OAL

M E T R I C

Designation DCONMS CND WF RADW OAL L3 LH RE Insert

MIFHR 8SC-8-SRK (1) 8.00 1.2 1.4 3.70 75.00 7.40 11.7 3.80 MI.R 8 SR 14-297 T-8/5
MIFHR 10C-8 10.00 5.0 1.4 4.50 102.50 7.40 12.5 3.80 MI.R 8 SR 14-297 T-8/5
MIFHR 12C-8 12.00 5.0 1.4 5.50 102.50 7.40 12.5 3.80 MI.R 8 SR 14-297 T-8/5
MIFHR 12C-10 (2) 12.00 6.0 2.4 5.50 90.00 11.20 17.2 4.60 MI.R 10 SR 34-506 M3X0.5 T-9/5
MIFHR 16C-10 (2) 16.00 6.0 2.4 7.50 90.00 11.20 17.2 4.60 MI.R 10 SR 34-506 M3X0.5 T-9/5
MIFHR 16C-15 16.00 8.0 2.7 7.50 100.00 12.50 19.0 10.30 MI.R 15 SR 34-506/L T-9/5 PL 16
MIFHR 20C-15 20.00 8.5 4.7 9.00 100.00 12.50 19.0 11.30 MI.R 15 SR 34-506/L T-9/5 PL 20
Solid carbide shank
(1)

Only face grooving inserts are available for this tool

(2)

For inserts, see pages: MEFL (35) • MIFR (34)

For holders, see pages: PICCO/MG PCO (Holder) (26)

MIFHR... 10 MIFHR... 8 RADW

MIFHR
Bars for Face and Internal
CND DCONMS
Grooving, Undercutting
and Threading Inserts RE RE
L3
LH WF
OAL

I N C H

Designation DCONMS CND WF RADW OAL L3 LH RE Insert

MIFHR 9.5C-8 .375 .196 .055 .169 4.030 .291 .492 .1490 MI.R 8 SR 14-297 T-8/5
MIFHR 12.7C-8 .500 .196 .055 .230 4.030 .291 .492 .1490 MI.R 8 SR 14-297 T-8/5
MIFHR 12.7C-10 (1) .500 .236 .094 .230 3.543 .440 .677 .1810 MI.R 10 SR 34-506 M3X0.5 T-9/5
MIFHR 15.9C-10 (1) .625 .236 .094 .287 3.543 .440 .677 .1810 MI.R 10 SR 34-506 M3X0.5 T-9/5
MIFHR 15.9C-15 .625 .315 .105 .295 3.937 .441 .748 .4010 MI.R 15 SR 34-506/L T-9/5 PL 062
MIFHR 19C-15 .750 .335 .183 .354 3.937 .492 .748 .4450 MI.R 15 SR 34-506/L T-9/5 PL 075
Only face grooving inserts are available for this tool
(1)

For inserts, see pages: MEFL (35) • MIFR (34)

31
FACE GROOVE-TURN
L3 LH
UNF 5/16”-24 typex3
MFHR-JHP
OAH
Square Shank Tools for HF H
MIFR 10 Face Grooving Inserts CDX Bar Max

DAXN B
CDX OAL

M E T R I C

Designation H B OAL LH L3 CDX DAXN(1) OAH HF Insert

MFHR 12C-10-JHP 12.0 12.0 100.00 27.0 5.20 9.00 10.0 20.0 12.0 MI.R 10 SR 34-506 M3X0.5 T-9/5 SR 5/16UNF TL360
MFHR 16C-10-JHP 16.0 16.0 100.00 27.0 5.20 9.00 10.0 24.0 16.0 MI.R 10 SR 34-506 M3X0.5 T-9/5 SR 5/16UNF TL360
MFHR 20C-10-JHP 20.0 20.0 100.00 30.0 5.20 9.00 10.0 28.0 20.0 MI.R 10 SR 34-506 M3X0.5 T-9/5 SR 5/16UNF TL360
• For DAXN, refer to insert data • For user guide and accessories, see pages 162-173
(1) Minimum axial grooving diameter

For inserts, see pages: MEFL (35) • MIFR (34)

Flow Rate vs. Pressure

70 Bar 100 Bar 140 Bar
Designation Flow Rate (liters/min) Flow Rate (liters/min) Flow Rate (liters/min)
MFHR 12C-10-JHP 3 5-9 9-11
MFHR 16C-10-JHP 3 7-9 9-11

IHSR-MIFR
Trepanning Cartridges Carrying WB
MINCUT Inserts Mounted on the CWN-CWX
DAXN
BHR MB32-32X63 Boring Head DAXX

OAL OAH

M E T R I C

Designation DAXN(1) DAXX(2) CWN(3) CWX(4) OAL WB OAH Insert

IHSR 8-21 MIFR8 8.0 21.0 1.50 2.20 32.00 23.00 17.50 MI.R 8 SR 14-297 T-8/5
IHSR 19-34 MIFR10 19.0 34.0 2.00 3.00 27.00 22.00 17.80 MI.R 10 SR 34-506 M3X0.5 T-9/5

I N C H

Designation DAXN(1) DAXX(2) CWN(3) CWX(4) OAL WB OAH Insert

IHSR 8-21 MIFR8 .31 .83 .059 .087 1.260 .906 .690 MI.R 8 SR 14-297 T-8/5
IHSR 19-34 MIFR10 .75 1.34 .079 .118 1.063 .866 .700 MI.R 10 SR 34-506 M3X0.5 T-9/5
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter
(3) Minimum cutting width
(4) Maximum cutting width

For inserts, see pages: MIFR (34)

For holders, see pages: BHR MB (33)

32 ISCAR
 FACE GROOVE-TURN
LF (assembly)
L1
BHR MB
Rough Boring Heads for
BD DCONMS DCN-DCX
Diameter Range 18-200 mm

IHSR
IHCR IHPR IHBR IHSR BW
A B C D

M E T R I C
kg
Designation BD DCONMS LF DCN(1) DCX(2) L1 IH(3) RPMX(4)
BHR MB32-32X63 32.00 32.00 63.00 35.5 50.0 - IH...36-50 10000 0.36
• Verify that the weight of the entire tool assembly does not exceed the machine spindle's carrying capability.
(1) Cutting diameter minimum
(2) Cutting diameter maximum
(3) Insert holders
(4) Maximum RPM

Spare Parts

Designation
BHR MB32-32X63 BH NUT BHR MB32 PLT 32* SR M5X25DIN912 SR M4X12 DIN913
* Optional, should be ordered separately

IHSR-MIFR

BHR MB

LF (assembly)
L1
BHR MB
Rough Boring Heads for
BD DCONMS DCN-DCX
Diameter Range .709-7.874"

IHSR
IHCR IHPR IHBR IHSR BW
A B C D

I N C H
Lbs
Designation BD DCONMS LF DCN(1) DCX(2) L1 IH(3) RPMX(4)
BHR MB32-32X63 1.260 1.260 2.480 1.398 1.968 - IH...36-50 10000 .79
• Verify that the weight of the entire tool assembly does not exceed the machine spindle's carrying capability.
(1) Cutting diameter minimum
(2) Cutting diameter maximum
(3) Insert holders
(4) Maximum RPM

Spare Parts

Designation
BHR MB32-32X63 BH NUT BHR MB32 PLT 32* SR M5X25DIN912 SR M4X12 DIN913

33
FACE GROOVE-TURN
MIFR 15 MIFR 10 MIFR 8
CDX PDY
MIFR S1
Screw-Clamped Inserts
DAXN-DAXX WF
for Internal Face Grooving INSL
CW CDX
and Turning
RE

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove f face-turn

IC908
Designation INSL CW CWTOL(1) RE RETOL(2) WF S1 DAXN(3) DAXX(4) CDX PDY (mm/rev) (mm/rev)
MIFR 8-1.50-0.20 17.70 1.50 0.02 0.20 0.020 2.60 6.5 8.0 11.5 5.50 11.00 • 0.02-0.10 0.02-0.06
MIFR 8-1.60-0.80 17.70 1.60 0.02 0.80 0.020 2.60 6.5 8.0 12.1 5.50 11.00 • 0.02-0.10 0.02-0.06
MIFR 8-2.00-0.20 17.70 2.00 0.02 0.20 0.020 2.80 6.5 8.0 16.0 5.50 11.00 • 0.02-0.10 0.02-0.06
MIFR 8-2.20-0.20 17.70 2.20 0.02 0.20 0.020 2.90 6.5 8.0 21.0 5.50 11.00 • 0.02-0.10 0.02-0.06
MIFR 10-2.00-0.20 25.10 2.00 0.02 0.20 0.020 3.00 7.6 10.0 - 9.00 14.80 • 0.02-0.10 0.02-0.06
MIFR 10-2.00-1.00 25.10 2.00 0.02 1.00 0.020 3.00 7.6 10.0 - 9.00 14.80 • 0.02-0.10 0.02-0.06
MIFR 10-2.50-0.20 25.10 2.50 0.02 0.20 0.020 3.10 7.6 10.0 30.0 9.00 14.80 • 0.02-0.10 0.02-0.06
MIFR 10-2.50-1.25 25.10 2.50 0.02 1.25 0.020 3.30 7.6 10.0 - 9.00 14.80 • 0.02-0.10 0.02-0.06
MIFR 10-3.00-0.20 25.10 3.00 0.02 0.20 0.020 3.40 7.6 10.0 30.0 9.00 14.80 • 0.02-0.10 0.02-0.06
MIFR 10-3.00-1.50 25.10 3.00 0.02 1.50 0.020 3.30 7.6 10.0 34.0 9.00 14.80 • 0.02-0.10 0.02-0.06
MIFR 15-2.50-0.20 30.00 2.50 0.02 0.20 0.020 5.55 9.0 15.0 60.0 15.00 19.30 • 0.03-0.05 0.03-0.04
MIFR 15-2.50-1.25 30.00 2.50 0.02 1.25 0.020 5.55 9.0 12.0 47.0 15.00 19.30 • 0.03-0.05 0.03-0.04
MIFR 15-3.00-0.20 30.00 3.00 0.02 0.20 0.020 5.85 9.0 15.0 60.0 15.00 19.30 • 0.03-0.05 0.03-0.04
MIFR 15-3.00-1.50 30.00 3.00 0.02 1.50 0.020 5.85 9.0 10.0 - 15.00 19.30 • 0.03-0.05 0.03-0.04
MIFR 15-3.50-0.20 30.00 3.50 0.02 0.20 0.020 6.00 9.0 10.0 - 15.00 19.30 • 0.03-0.05 0.03-0.04

I N C H
Recommended
Dimensions
Machining Data

f face-groove f face-turn

IC908
Designation INSL CW CWTOL(1) RE RETOL(2) WF S1 DAXN(3) DAXX(4) CDX PDY (IPR) (IPR)
MIFR 8-1.50-0.20 .697 .059 .0008 .0079 .0008 .102 .256 .31 .45 .217 .433 • .0008-.0039 .0008-.0024
MIFR 8-1.60-0.80 .697 .063 .0008 .0315 .0008 .102 .256 .31 .48 .217 .433 • .0008-.0039 .0008-.0024
MIFR 8-2.00-0.20 .697 .079 .0008 .0079 .0008 .110 .256 .31 .63 .217 .433 • .0008-.0039 .0008-.0024
MIFR 8-2.20-0.20 .697 .087 .0008 .0079 .0008 .114 .256 .31 .83 .217 .433 • .0008-.0039 .0008-.0024
MIFR 10-2.00-0.20 .988 .079 .0008 .0079 .0008 .118 .299 .39 - .354 .583 • .0008-.0039 .0008-.0024
MIFR 10-2.00-1.00 .988 .079 .0008 .0394 .0008 .118 .299 .39 - .354 .583 • .0008-.0039 .0008-.0024
MIFR 10-2.50-0.20 .988 .098 .0008 .0079 .0008 .122 .299 .39 1.18 .354 .583 • .0008-.0039 .0008-.0024
MIFR 10-2.50-1.25 .988 .098 .0008 .0492 .0008 .130 .299 .39 - .354 .583 • .0008-.0039 .0008-.0024
MIFR 10-3.00-0.20 .988 .118 .0008 .0079 .0008 .134 .299 .39 1.18 .354 .583 • .0008-.0039 .0008-.0024
MIFR 10-3.00-1.50 .988 .118 .0008 .0590 .0008 .130 .299 .39 1.34 .354 .583 • .0008-.0039 .0008-.0024
MIFR 15-2.50-0.20 1.181 .098 .0008 .0079 .0008 .219 .354 .59 2.36 .591 .760 • .0012-.0020 .0012-.0016
MIFR 15-2.50-1.25 1.181 .098 .0008 .0492 .0008 .219 .354 .47 1.85 .591 .760 • .0012-.0020 .0012-.0016
MIFR 15-3.00-0.20 1.181 .118 .0008 .0079 .0008 .230 .354 .59 2.36 .591 .760 • .0012-.0020 .0012-.0016
MIFR 15-3.00-1.50 1.181 .118 .0008 .0590 .0008 .230 .354 .39 - .591 .760 • .0012-.0020 .0012-.0016
MIFR 15-3.50-0.20 1.181 .138 .0008 .0079 .0008 .236 .354 .39 - .591 .760 • .0012-.0020 .0012-.0016
• Recommended cutting speeds and feeds can increased by 20-30% for aluminum, and reduced by 20-30% for titanium and Inconel
• For cutting speed recommendations, see pages 162-164
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Maximum axial grooving diameter

For tools, see pages: IHSR-MIFR (32) • MFHR-JHP (32) • MIFHR (31)

34 ISCAR
 FACE GROOVE-TURN
INSL
PDY WF
MEFL DAXN-DAXX
S1
Screw-Clamped Inserts for DAXN-DAXX
External Face Grooving and CDX
Turning Next to Shafts CW
CDX RE

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove f face-turn

IC908
Designation CW RE CWTOL(1) RETOL(2) WF S1 CDX PDY INSL DAXN(3) DAXX(4) (mm/rev) (mm/rev)
MEFL 8-1.50-0.20 1.50 0.20 0.02 0.020 2.60 6.6 5.50 11.00 17.40 8.0 15.0 • 0.02-0.10 0.02-0.06
MEFL 8-1.60-0.80 1.60 0.80 0.02 0.020 2.70 6.6 5.50 11.00 17.40 7.0 12.1 • 0.02-0.10 0.02-0.06
MEFL 8-2.00-0.20 2.00 0.20 0.02 0.020 3.10 6.6 5.50 11.00 17.40 7.0 20.0 • 0.02-0.10 0.02-0.06
MEFL 8-2.00-1.00 2.00 1.00 0.02 0.020 2.90 6.6 5.50 11.00 17.40 7.0 14.0 • 0.02-0.10 0.02-0.06
MEFL 8-2.20-0.20 2.20 0.20 0.02 0.020 3.10 6.6 5.50 11.00 17.40 7.0 20.0 • 0.02-0.10 0.02-0.06
MEFL 10-2.50-0.20 2.50 0.20 0.02 0.020 3.15 7.6 9.00 14.85 24.50 10.0 45.0 • 0.02-0.06 0.02-0.05
MEFL 10-2.50-1.25 2.50 1.25 0.02 0.020 3.15 7.6 9.00 14.85 24.50 10.0 45.0 • 0.02-0.06 0.02-0.05
MEFL 10-3.00-0.20 3.00 0.20 0.02 0.020 3.60 7.6 9.00 14.85 24.50 10.0 100.0 • 0.02-0.06 0.02-0.05
MEFL 10-3.00-1.50 3.00 1.50 0.02 0.020 3.40 7.6 9.00 14.85 24.50 10.0 100.0 • 0.02-0.06 0.02-0.05

I N C H
Recommended
Dimensions
Machining Data

f face-groove f face-turn

IC908
Designation CW RE CWTOL(1) RETOL(2) WF S1 CDX PDY INSL DAXN(3) DAXX(4) (IPR) (IPR)
MEFL 8-1.50-0.20 .059 .0079 .0008 .0008 .102 .260 .217 .433 .685 .31 .59 • .0008-.0039 .0008-.0024
MEFL 8-1.60-0.80 .063 .0315 .0008 .0008 .106 .260 .217 .433 .685 .28 .48 • .0008-.0039 .0008-.0024
MEFL 8-2.00-0.20 .079 .0079 .0008 .0008 .122 .260 .217 .433 .685 .28 .79 • .0008-.0039 .0008-.0024
MEFL 8-2.00-1.00 .079 .0394 .0008 .0008 .114 .260 .217 .433 .685 .28 .55 • .0008-.0039 .0008-.0024
MEFL 8-2.20-0.20 .087 .0079 .0008 .0008 .122 .260 .217 .433 .685 .28 .79 • .0008-.0039 .0008-.0024
MEFL 10-2.50-0.20 .098 .0079 .0008 .0008 .124 .299 .354 .585 .965 .39 1.77 • .0008-.0024 .0008-.0020
MEFL 10-2.50-1.25 .098 .0492 .0008 .0008 .124 .299 .354 .585 .965 .39 1.77 • .0008-.0024 .0008-.0020
MEFL 10-3.00-0.20 .118 .0079 .0008 .0008 .142 .299 .354 .585 .965 .39 3.94 • .0008-.0024 .0008-.0020
MEFL 10-3.00-1.50 .118 .0590 .0008 .0008 .134 .299 .354 .585 .965 .39 3.94 • .0008-.0024 .0008-.0020
• For cutting speed recommendations, see pages 162-164
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Maximum axial grooving diameter

For tools, see pages: MFHR-JHP (32) • MIFHR (31)

35
FACE GROOVE-TURN
KITS

MINCUT KIT
Contains One Toolholder and
a Set of 6 Different Inserts
for Internal Face Grooving
and Turning Applications

M E T R I C
Designation Qty
KIT MINCUT 7

Catalog No Designation Quantity

2801631 MIFHR 12.7C-8 1
6404029 MIGR 8-1.60-0.80 1
6404045 MIFR 8-2.20-0.20 1
6404049 MIFR 8-1.60-0.80 1
6405165 MITR 8-MT1-0.05 1
6405188 MIUR 8-1.00-0.50 1
6405194 MIGR 8-2.00-0.10 1

KITS

MINCUT KIT
Contains One Toolholder and
a Set of 6 Different Inserts
for Internal Face Grooving
and Turning Applications

I N C H
Designation Qty
KIT MINCUT INCH 7

Catalog No Designation Quantity

2801631 MIFHR 12.7C-8 1
6404029 MIGR 8-1.60-0.80 1
6404045 MIFR 8-2.20-0.20 1
6404049 MIFR 8-1.60-0.80 1
6405165 MITR 8-MT1-0.05 1
6405188 MIUR 8-1.00-0.50 1
6405194 MIGR 8-2.00-0.10 1

36 ISCAR
 FACE GROOVE-TURN
HELIFACE
CW
CDX
HFFH
Face Grooving Blades
H
HF
DAXN-DAXX

WF
OAL WB_2
Right-hand shown

M E T R I C
Designation DAXN(1) DAXX(2) CW CDX WF WB_2 HF H OAL
HFFH 38R/L-2 38.0 45.0 2.00 14.00 4.50 5.2 24.8 32.0 150.00
HFFH 45R/L-2 45.0 60.0 2.00 14.00 4.40 5.2 24.8 32.0 150.00
HFFH 60R/L-2 60.0 80.0 2.00 14.00 4.40 5.2 24.8 32.0 150.00
HFFH 80R/L-2 80.0 100.0 2.00 14.00 4.40 5.2 24.8 32.0 150.00
HFFH 100R/L-2 100.0 130.0 2.00 14.00 4.40 5.2 24.8 32.0 150.00

I N C H
Designation DAXN(1) DAXX(2) CW CDX WF WB_2 HF H OAL
HFFH 38R/L-2 1.50 1.77 .079 .551 .177 .205 .976 1.260 5.906
HFFH 45R/L-2 1.77 2.36 .079 .551 .173 .205 .976 1.260 5.906
HFFH 60R/L-2 2.36 3.15 .079 .551 .173 .205 .976 1.260 5.906
HFFH 80R/L-2 3.15 3.94 .079 .551 .173 .205 .976 1.260 5.906
HFFH 100R/L-2 3.94 5.12 .079 .551 .173 .205 .976 1.260 5.906
• H dimension links blades and blocks
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: HFPN (67)

For holders, see pages: C#-TBK-R/L (138) • HSK A-WH-TBK-R/L (148) • SGTBF (136) • SGTBK (135) • SGTBU/SGTBN (133) • UBHCR/L (135)

Spare Parts

Designation
HFFH EDG 33B*
* Optional, should be ordered separately

37
FACE GROOVE-TURN
WF

HFFA DAXN-DAXX
Reinforced Face Grooving Blades HF
H

OAL WB_2
CW

CDX Right-hand shown

M E T R I C
Designation CW DAXN(1) DAXX(2) CDX H WF HF OAL WB_2
HFFA 27R/L-2 2.00 27.0 29.0 14.00 32.0 9.50 24.8 102.00 21.0
HFFA 29R/L-2 2.00 29.0 33.0 14.00 32.0 9.50 24.8 102.00 18.5
HFFA 33R/L-2 2.00 33.0 38.0 14.00 32.0 9.50 24.8 102.00 17.5
HFFA 38R/L-2 2.00 38.0 46.0 14.00 32.0 9.50 24.8 102.00 13.5
HFFA 46R/L-2 2.00 46.0 60.0 14.00 32.0 9.50 24.8 102.00 13.5
HFFA 60R/L-2 2.00 60.0 80.0 14.00 32.0 9.50 24.8 102.00 14.0
HFFA 80R/L-2 2.00 80.0 105.0 14.00 32.0 9.50 24.8 102.00 16.1

I N C H
Designation CW DAXN(1) DAXX(2) CDX H WF HF OAL WB_2
HFFA 27R/L-2 .079 1.06 1.14 .551 1.260 .374 .976 4.016 .827
HFFA 29R/L-2 .079 1.14 1.30 .551 1.260 .374 .976 4.016 .728
HFFA 33R/L-2 .079 1.30 1.50 .551 1.260 .374 .976 4.016 .689
HFFA 38R/L-2 .079 1.50 1.81 .551 1.260 .374 .976 4.016 .531
HFFA 46R/L-2 .079 1.81 2.36 .551 1.260 .374 .976 4.016 .531
HFFA 60R/L-2 .079 2.36 3.15 .551 1.260 .374 .976 4.016 .551
HFFA 80R/L-2 .079 3.15 4.13 .551 1.260 .374 .976 4.016 .634
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: HFPN (67)

For holders, see pages: SGTBF (136) • SGTBU/SGTBN (133) • UBHCR/L (135)

Spare Parts

Designation
HFFA EDG 33B*
* Optional, should be ordered separately

38 ISCAR
 FACE GROOVE-TURN
LH

HGHR/L-3 H OAH
Integral Holders for Face
DAXN-DAXX
Grooving and Turning CDX HBH OAW
OAL
CDX
WF CW B
Right-hand shown

M E T R I C

Designation H B CW CDX HBH WF DAXN(1) DAXX(2) OAL LH OAH OAW

HGHR 1010-12-3T6 10.0 10.0 3.00 6.00 2.0 9.50 12.0 16.0 120.00 19.0 19.0 13.70 SR 76-1400 T-20/3
HGHR 1010-16-3T6 10.0 10.0 3.00 6.00 2.0 9.50 16.0 25.0 120.00 19.0 19.0 12.80 SR 76-1400 T-20/3
HGHR/L 1212-12-3T6 12.0 12.0 3.00 6.00 - 11.00 12.0 16.0 120.00 19.0 19.0 15.70 SR 76-1400 T-20/3
HGHR 1212-16-3T6 12.0 12.0 3.00 6.00 - 11.00 16.0 25.0 120.00 19.0 19.0 14.80 SR 76-1400 T-20/3
HGHR/L 1616-12-3T6 16.0 16.0 3.00 6.00 - 15.00 12.0 16.0 120.00 19.0 21.0 19.70 SR 76-1400 T-20/3
HGHR/L 1616-16-3T6 16.0 16.0 3.00 6.00 - 15.00 16.0 25.0 120.00 19.0 21.0 18.80 SR 76-1400 T-20/3
HGHR/L 2020-12-3T6 20.0 20.0 3.00 6.00 - 20.00 12.0 16.0 120.00 19.0 25.0 24.00 SR 76-1400 T-20/3
HGHR/L 2020-16-3T6 20.0 20.0 3.00 6.00 - 20.00 16.0 25.0 120.00 19.0 25.0 24.00 SR 76-1400 T-20/3
HGHR/L 2525-12-3T6 25.0 25.0 3.00 6.00 - 25.00 12.0 16.0 120.00 19.0 30.0 29.00 SR 76-1400 T-20/3
HGHR/L 2525-16-3T6 25.0 25.0 3.00 6.00 - 25.00 16.0 25.0 120.00 19.0 30.0 29.00 SR 76-1400 T-20/3
• HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GRIP (70) • GRIP (full radius) (72) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)

Groove can be widened with no limitation toward or away

d
from the center except for the following tools:
HGHR/L...-12-3T6
D d Limitation of widening toward center
12.0 4.0 depends on the major diameter (D) as
13.0 1.0 per chart. D
13.5 0

LH

HGHR/L-3 H OAH
Integral Holders for Face
DAXN-DAXX
Grooving and Turning CDX HBH OAW
OAL
CDX
WF CW B
Right-hand shown

I N C H

Designation CW CDX H B HBH DAXN(1) DAXX(2) WF OAH OAW OAL LH

HGHL 9.5-12-3T6 .118 .236 .375 .375 .12 .47 .63 .370 .67 .559 5.000 .750 SR 76-1400 T-20/3
HGHL 12.7-12-3T6 .118 .236 .500 .500 .12 .47 .63 .460 .70 .646 5.000 .750 SR 76-1400 T-20/3
HGHL 12.7-16-3T6 .118 .236 .500 .500 .12 .63 .98 .460 .70 .619 5.000 .750 SR 76-1400 T-20/3
HGHR/L 15.9-12-3T6 .118 .236 .625 .625 .12 .47 .63 .590 .82 .771 5.000 .750 SR 76-1400 T-20/3
HGHR/L 19-12-3T6 .118 .236 .750 .750 - .47 .63 .750 .95 .907 5.000 .750 SR 76-1400 T-20/3
HGHR/L 19-16-3T6 .118 .236 .750 .750 - .63 .98 .750 .95 .907 5.000 .750 SR 76-1400 T-20/3
HGHR/L 25.4-12-3T6 .118 .236 1.000 1.000 - .47 .63 1.000 1.20 1.157 5.000 .750 SR 76-1400 T-20/3
HGHR/L 25.4-16-3T6 .118 .236 1.000 1.000 - .63 .98 1.000 1.20 1.157 5.000 .750 SR 76-1400 T-20/3
HGHR 9.5-16-3T6 .118 .236 .375 .375 .12 .63 .98 .370 .67 .524 5.000 .750 SR 76-1400 T-20/3
HGHR 15.9-16-3T6 .118 .236 .625 .625 .12 .63 .98 .590 .82 .735 5.000 .750 SR 76-1400 T-20/3
• HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GRIP (70) • GRIP (full radius) (72) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)

Groove can be widened with no limitation toward or away

d
from the center except for the following tools:
HGHR/L...-12-3T6
D d
.472 .157 Limitation of widening toward center
.512 .039 depends on the major diameter (D) as D
.513 0 per chart

39
FACE GROOVE-TURN
LH
HFHR/L-3T
Integral Holders for Facing CDX HF OAH
HFHR/L --3T12 H
WF2
CW
DAXN-DAXX

CDX WF B

OAL Right-hand shown

M E T R I C

Designation CW CDX H HF B OAL WF WF2 DAXN(2) DAXX(3) LH OAH

HFHR/L 20-25-3T12 3.00 12.00 20.0 20.0 20.0 140.00 20.50 5.3 25.0 30.0 38.0 28.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-30-3T12 3.00 12.00 20.0 20.0 20.0 140.00 20.50 5.3 30.0 38.0 38.0 29.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-38-3T12 3.00 12.00 20.0 20.0 20.0 140.00 20.50 5.3 38.0 48.0 38.0 30.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-48-3T12 3.00 12.00 20.0 20.0 20.0 140.00 20.50 5.3 48.0 60.0 38.0 30.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-25-3T12 3.00 12.00 25.0 25.0 25.0 150.00 25.50 5.3 25.0 30.0 38.0 33.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-30-3T12 3.00 12.00 25.0 25.0 25.0 150.00 25.50 5.3 30.0 38.0 38.0 34.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-38-3T12 3.00 12.00 25.0 25.0 25.0 150.00 25.50 5.3 38.0 48.0 38.0 35.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-60-3T22 (1) 3.00 22.00 20.0 20.0 20.0 140.00 20.50 - 60.0 75.0 40.0 31.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-48-3T22 (1) 3.00 22.00 25.0 25.0 25.0 150.00 25.50 - 48.0 60.0 40.0 36.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-60-3T22 (1) 3.00 22.00 25.0 25.0 25.0 150.00 25.50 - 60.0 75.0 40.0 36.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-75-3T25 (1) 3.00 25.00 20.0 20.0 20.0 140.00 20.50 - 75.0 100.0 43.0 31.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-75-3T25 (1) 3.00 25.00 25.0 25.0 25.0 150.00 25.50 - 75.0 100.0 43.0 36.0 SR M6X16 DIN912 HW 5.0
• For user guide, see pages 161-173
(1) For deep face grooving only.
(2) Minimum penetration diameter
(3) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

Groove can be widened with no limitation toward or away

d
from the center except for the following tools:
HFHR/L-#-25-3T12
D d Limitation of widening toward
25 5 center (d) depends on the major D
26 2 diameter (D) as per chart
≥27 0

LH
HFHR/L-3T
Integral Toolholders for CDX H OAH
HFHR/L --3T12 H
External Facing WF2
CW
DAXN-DAXX
CDX WF B
.83
OAL Right-hand shown

I N C H

Designation CW CDX H B OAL WF F1 DAXN(2) DAXX(3) LH OAH

HFHR/L 25.4-25-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 .98 1.18 1.500 1.31 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-30-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 1.18 1.50 1.500 1.35 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-38-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 1.50 1.89 1.500 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-48-3T22 (1) .118 .870 1.000 1.000 6.000 1.020 - 1.89 2.36 1.570 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-60-3T22 (1) .118 .870 1.000 1.000 6.000 1.020 - 2.36 2.96 1.570 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-75-3T25 (1) .118 .980 1.000 1.000 6.000 1.020 - 2.95 3.94 1.690 1.43 SR M6X16 DIN912 HW 5.0
• For user guide, see pages 161-173
(1) For deep face grooving only.
(2) Minimum penetration diameter
(3) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

Groove can be widened with no limitation toward or away d

from the center except for the following tools:
HFHR/L-#-25-3T12
D d
Limitation of widening toward
.98 .20 D
center (d) depends on the major
1.02 .08 diameter (D) as per chart
≥1.06 0

40 ISCAR
 FACE GROOVE-TURN
LH

HFHR/L-4T
HF OAH
Integral Holders for Facing CDX
H
HFHR/L --4T12
WF2 CW HBH
DAXN-DAXX
WF B
CDX
OAL Right-hand shown

M E T R I C

Designation CW CDX H HF B OAL WF WF2 DAXN(1) DAXX(2) LH OAH HBH

HFHR/L 20-25-4T12 4.00 12.00 20.0 20.0 20.0 140.00 20.60 6.2 25.0 29.0 39.0 29.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-29-4T12 4.00 12.00 20.0 20.0 20.0 140.00 20.60 6.2 29.0 34.0 39.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-25-4T12 4.00 12.00 25.0 25.0 25.0 150.00 25.60 6.2 25.0 29.0 39.0 34.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-29-4T12 4.00 12.00 25.0 25.0 25.0 150.00 25.60 6.2 29.0 34.0 39.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-34-4T20 4.00 20.00 20.0 20.0 20.0 140.00 20.60 - 34.0 40.0 39.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-34-4T20 4.00 20.00 25.0 25.0 25.0 150.00 25.60 - 34.0 40.0 39.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-40-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 40.0 48.0 44.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-48-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 48.0 60.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-60-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 60.0 75.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-75-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 75.0 100.0 44.0 34.0 2.0 SR M6X16 DIN912 HW 5.0
HFHL 25-100-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 100.0 140.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-140-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.74 - 140.0 240.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-240-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 240.0 800.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-40-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 40.0 48.0 44.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-48-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 48.0 60.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-60-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 60.0 75.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-75-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 75.0 100.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR 25-100-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.74 - 100.0 140.0 44.0 37.0 -
HFHR 25-140-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 140.0 240.0 44.0 37.0 -
HFHR 25-75-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.80 - 75.0 100.0 44.0 37.0 -
• DGN & GRIP 4 mm inserts can be used only with right-hand tools, HGPL 4 mm with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • HGPL (75)

Groove can be widened with no limitation toward or away

from the center except for the following tools:
d
HFHR/L-#-25-4T12 HFHR/L-#-29-4T12
Limitation of widening toward
D d D d center (d) depends on the major
D
25 1 29 1 diameter (D) as per chart
≥26 0 ≥46 0

41
FACE GROOVE-TURN
LH

HFHR/L-4T
OAH
Integral Toolholders for CDX H H
HFHR/L --4T12
External Facing WF2 CW HBH
DAXN-DAXX
WF B
CDX
.826 OAL Right-hand shown

I N C H

Designation CW CDX F1 H B OAL WF DAXN(1) DAXX(2) LH OAH

HFHR 25.4-25-4T12 .157 .470 .24 1.000 1.000 6.000 1.020 .98 1.14 1.540 1.35 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-29-4T12 .157 .470 .24 1.000 1.000 6.000 1.020 1.14 1.34 1.540 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-34-4T20 .157 .790 .24 1.000 1.000 6.000 1.020 1.34 1.57 1.540 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-40-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 1.57 1.89 1.730 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-48-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 1.89 2.36 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-60-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 2.36 2.95 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-75-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 2.95 3.94 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-100-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 3.94 5.51 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-140-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 5.51 9.45 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-240-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 9.45 31.50 1.730 1.47 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 4.. inserts can be used only with right-hand tools, HGPL 4.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: DGN-MF (80) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72)
• HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)

Groove can be widened with no limitation toward or away

from the center except for the following tools:
d
HFHR/L-#-25-4T12 HFHR/L-#-29-4T12
Limitation of widening toward
D d D d center (d) depends on the major
D
.98 .04 1.14 .04 diameter (D) as per chart
≥1.02 0 ≥1.8 0

42 ISCAR
 FACE GROOVE-TURN
LH

HFHR/L-5T
OAH
Integral Toolholders for CDX
HF H
HFHR/L --5T10
External Facing WF2 CW HBH
DAXN-DAXX
WF B
CDX
OAL Right-hand shown

M E T R I C

Designation CW CDX H HF B OAL WF2 WF DAXN(1) DAXX(2) LH OAH HBH

HFHR/L 20-25-5T10 5.00 10.00 20.0 20.0 20.0 140.00 7.1 21.00 25.0 30.0 38.0 28.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-25-5T10 5.00 10.00 25.0 25.0 25.0 150.00 7.1 26.00 25.0 30.0 38.0 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-110-5T14 5.00 14.00 25.0 25.0 25.0 150.00 - 23.50 110.0 200.0 32.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-52-5T14 5.00 14.00 25.0 25.0 25.0 150.00 - 23.50 52.0 75.0 32.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-75-5T14 5.00 14.00 25.0 25.0 25.0 150.00 - 23.50 75.0 110.0 32.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-28-5T15 5.00 17.00 20.0 20.0 20.0 140.00 - 21.00 28.0 31.0 34.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-31-5T15 5.00 17.00 20.0 20.0 20.0 140.00 - 21.00 31.0 35.0 34.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-28-5T15 5.00 17.00 25.0 25.0 25.0 150.00 - 26.00 28.0 31.0 34.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-31-5T15 5.00 17.00 25.0 25.0 25.0 150.00 - 26.00 31.0 35.0 34.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-35-5T20 5.00 20.00 20.0 20.0 20.0 140.00 - 21.00 35.0 40.0 39.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-40-5T20 5.00 20.00 20.0 20.0 20.0 140.00 - 21.00 40.0 45.0 39.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-200-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 23.50 200.0 800.0 32.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-35-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 26.00 35.0 40.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-40-5T20 5.00 20.00 25.0 25.0 25.0 140.00 - 26.00 40.0 45.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR 25-200-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 26.00 200.0 800.0 32.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR 25-40-5T20 5.00 20.00 25.0 25.0 25.0 150.00 - 26.00 40.0 45.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-45-5T25 5.00 25.00 20.0 20.0 20.0 140.00 - 21.00 45.0 55.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-55-5T25 5.00 25.00 20.0 20.0 20.0 140.00 - 21.00 55.0 70.0 44.0 35.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-45-5T25 5.00 25.00 25.0 25.0 25.0 150.00 - 26.00 45.0 55.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-55-5T25 5.00 25.00 25.0 25.0 25.0 150.00 - 26.00 55.0 70.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-70-5T28 5.00 28.00 20.0 20.0 20.0 140.00 - 21.00 70.0 95.0 47.0 35.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-130-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 130.0 180.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-180-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 180.0 800.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-70-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 70.0 95.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-95-5T32 5.00 32.00 25.0 25.0 25.0 150.00 - 26.00 95.0 130.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
• DGN & GRIP 5.. inserts can be used only with right-hand tools, HGPL 5.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GRIPA (73) • GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72)
• DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)

Groove can be widened with no limitation toward or away

from the center except for the following tools:
HFHR/L- o -31-5T15 HFHR/L-o-25-5T10 HFHR/L- o -28-5T15 d
D d D d D d Limitation of widening
31 15 25 4 28 13 toward center (d)
32 10 26 1 29 8 depends on the major
33 7 ≥27 0 30 5 diameter (D) as per D
34 4 31 3 chart
35 2 32 1
≥36 0 ≥33 0

43
FACE GROOVE-TURN
LH

HFHR/L-5T
OAH
Integral Toolholders for CDX H H
HFHR/L --5T10
External Facing WF2 CW HBH
DAXN-DAXX
WF B
CDX
.826 OAL Right-hand shown

I N C H

Designation CW CDX H B OAL F1 WF DAXN(1) DAXX(2) LH OAH

HFHR/L 25.4-25-5T10 .197 .390 1.000 1.000 6.000 .28 1.040 .98 1.18 1.500 1.31 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-28-5T15 .197 .670 1.000 1.000 6.000 - 1.040 1.10 1.22 1.340 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-31-5T15 .197 .670 1.000 1.000 6.000 - 1.040 1.22 1.38 1.340 1.39 SR M6X16 DIN912 HW 5.0
HFHR 25.4-35-5T20 .197 .790 1.000 1.000 6.000 - 1.040 1.38 1.57 1.540 1.43 SR M6X16 DIN912 HW 5.0
HFHR 25.4-40-5T20 .197 .790 1.000 1.000 6.000 - 1.040 1.57 1.77 1.540 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-55-5T25 .197 .980 1.000 1.000 6.000 - 1.040 2.17 2.76 1.730 1.43 SR M6X16 DIN912 HW 5.0
HFHR 25.4-45-5T25 .197 .980 1.000 1.000 6.000 - 1.040 1.77 2.17 1.730 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-70-5T32 .197 1.260 1.000 1.000 6.000 - 1.040 2.76 3.74 2.000 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-95-5T32 .197 1.260 1.000 1.000 6.000 - 1.040 3.74 5.12 2.000 1.43 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 5.. inserts can be used only with right-hand tools, HGPL 5.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: DGN-W (81) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72) • GRIPA (73)
• GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)

Groove can be widened with no limitation toward or away

from the center except for the following tools:
HFHR/L-#-31-5T15 HFHR/L-#-28-5T15 HFHR/L-#-25-5T10 d

D d D d D d Limitation of widening
1.22 .59 1.10 .51 .98 .16 toward center (d)
1.26 .39 1.14 .31 1.02 .04 depends on the major
1.30 .28 1.18 .20 ≥1.06 0 D
diameter (D) as per
1.34 .16 1.22 .12 chart
1.38 .08 1.29 .04
≥1.42 0 ≥1.30 0

44 ISCAR
 FACE GROOVE-TURN
LH

HFHR/L-6T
OAH
Integral Toolholders for CDX
HF H
HFHR/L --6T10
External Facing WF2 CW HBH
DAXN-DAXX
WF B
CDX
OAL Right-hand shown

M E T R I C

Designation CW CDX H HF B OAL WF2 WF DAXN(1) DAXX(2) LH OAH HBH

HFHL 20-26-6T10 6.00 10.00 20.0 20.0 20.0 140.00 7.9 21.40 26.0 30.0 39.0 29.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-30-6T15 6.00 17.00 20.0 20.0 20.0 140.00 - 21.40 30.0 38.0 36.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-30-6T15 6.00 17.00 25.0 25.0 25.0 150.00 - 26.40 30.0 38.0 36.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-38-6T20 6.00 20.00 20.0 20.0 20.0 140.00 - 21.40 38.0 50.0 39.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-100-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 26.00 100.0 200.0 40.0 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-200-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 23.00 200.0 3000.0 37.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-38-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 26.40 38.0 50.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-50-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 23.00 50.0 65.0 37.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-65-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 23.00 65.0 100.0 37.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-50-6T25 6.00 25.00 20.0 20.0 20.0 140.00 - 21.40 50.0 70.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-50-6T25 6.00 25.00 25.0 25.0 25.0 150.00 - 26.40 50.0 70.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-100-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 100.0 180.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-180-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 180.0 400.0 51.0 40.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-400-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 400.0 3000.0 51.0 40.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-70-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 70.0 100.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
• DGN & GRIP 6.. inserts can be used only with right-hand tools, HGPL 6.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • HGPL (75)

Groove can be widened with no limitation toward or away

from the center except for the following tools: d
HFHR/L-#-30-6T10
D d
30 7
31 4 Limitation of widening toward
center (d) depends on the major D
32 1
diameter (D) as per chart
≥33 0

45
FACE GROOVE-TURN
LH

HFHR/L-6T
OAH
Integral Toolholders for CDX H H
HFHR/L --6T10
External Facing WF2 CW HBH
DAXN-DAXX
WF B
CDX
.826 OAL Right-hand shown

I N C H

Designation CW CDX H B OAL WF DAXN(1) DAXX(2) LH OAH HBH

HFHR/L 25.4-30-6T15 .236 .670 1.000 1.000 6.000 1.050 1.18 1.50 1.420 1.39 - SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-38-6T20 .236 .790 1.000 1.000 6.000 1.050 1.50 1.97 1.540 1.43 - SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-50-6T25 .236 .980 1.000 1.000 6.000 1.050 1.97 2.76 1.730 1.47 - SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-70-6T32 .236 1.260 1.000 1.000 6.000 1.050 2.76 3.94 2.000 1.47 - SR M6X16 DIN912 HW 5.0
HFHR 25.4-100-6T20 .236 .790 1.000 1.000 6.000 1.050 3.94 7.09 2.000 1.47 - SR M6X20 DIN912 HW 5.0
HFHR/L 25.4-100-6T32 .236 1.260 1.000 1.000 6.000 1.050 3.94 7.09 2.000 1.47 - SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-180-6T32 .236 1.260 1.000 1.000 6.000 1.050 7.09 15.80 2.000 1.57 .10 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 6.. inserts can be used only with right-hand tools, HGPL 6.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72) • HFPR/L (68)
• HFPR/L (full radius) (69) • HGPL (75)

Groove can be widened with no limitation toward or away

from the center except for the following tools: d

HFHR/L-#-30-6T15
D d
1.18 .28
1.22 .16 Limitation of widening toward
D
center (d) depends on the major
1.26 .04
diameter (D) as per chart
≥1.30 0

46 ISCAR
 FACE GROOVE-TURN
H OAH
HBH
LH
OAW
MAHPR/L-XL-JHP OAL
Holders with High-Pressure
B HF
Coolant Channels for
MODULAR-GRIP Perpendicularly MHD L5
MHD_2 Right-hand shown
Mounted Adapters
M E T R I C
Designation H B LH OAL HBH OAH OAW HF L5 MHD MHD_2
MAHPR/L-XL-20-JHP-MCG 20.0 20.0 23.0 120.00 24.0 53.00 45.00 20.0 29.00 50.00 85.00
MAHPR/L-XL-25-JHP-MCG 25.0 25.0 15.0 120.00 19.0 53.00 45.50 25.0 35.00 50.00 90.00
For tools, see pages: • HFPAD-JHP (48) • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHPR/L-XL-20-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X4 DIN913 TL360 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377
MAHPR/L-XL-25-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X4 DIN913 TL360 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377

H OAH
HBH
LH
OAW
MAHPR/L-XL-JHP OAL
Holders with High-Pressure
B HF
Coolant Channels for
MODULAR-GRIP Perpendicularly MHD L5
MHD_2 Right-hand shown
Mounted Adapters
I N C H
Designation H B LH OAL HBH OAH OAW HF L5 MHD MHD_2
MAHPR/L-XL-19-JHP-MCG .750 .750 .591 4.724 1.000 2.087 1.772 .750 1.142 1.968 3.346
MAHPR/L-XL-25.4-JHP-MCG 1.000 1.000 .591 4.724 .748 2.087 1.791 1.000 1.378 1.968 3.543
For tools, see pages: • HFPAD-JHP (48) • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHPR/L-XL-19-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X3 DIN913 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377
MAHPR/L-XL-25.4-JHP-MCG SR M5-04451 T-20/5 SR M6X20 DIN912 HW 5.0 OR 5X1N SR M4X3 DIN913 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377

47
FACE GROOVE-TURN

HFPAD-JHP
Adapters for Face Machining ØDAXN-DAXX
HF
OAH

OAL
WF WB
CDX
CW Right-hand shown

M E T R I C
Designation CW CDX WF WB OAL HF OAH DAXN(1) DAXX(2)
HFPAD 3R/L-40-T10-JHP 3.00 10.00 4.80 5.80 39.50 24.0 33.00 40.0 65.0
HFPAD 3R/L-115-T18-JHP 3.00 18.00 4.80 5.80 43.50 24.0 33.00 115.0 400.0
HFPAD 3R/L-65-T18-JHP 3.00 18.00 4.80 5.80 43.50 24.0 33.00 65.0 115.0
HFPAD 4R/L-44-T14-JHP 4.00 14.00 4.80 5.80 40.50 24.0 33.00 44.0 58.0
HFPAD 4R/L-58-T14-JHP 4.00 14.00 4.80 5.80 40.50 24.0 33.00 58.0 88.0
HFPAD 4R/L-88-T14-JHP 4.00 14.00 4.50 5.80 40.50 24.0 33.00 88.0 175.0
HFPAD 4R/L-175-T20-JHP 4.00 20.00 4.80 6.50 45.50 24.0 33.00 175.0 800.0
HFPAD 5R/L-110-T14-JHP 5.00 14.00 4.50 6.30 45.50 24.0 33.00 110.0 200.0
HFPAD 5R/L-40-T14-JHP 5.00 14.00 4.50 6.30 40.50 24.0 33.00 40.0 50.0
HFPAD 5L-50-T14-JHP 5.00 14.00 4.50 6.30 40.50 24.0 33.00 50.0 75.0
HFPAD 5R/L-75-T14-JHP 5.00 14.00 4.50 6.30 40.50 24.0 33.00 75.0 110.0
HFPAD 5R/L-200-T20-JHP 5.00 20.00 4.50 6.60 45.50 24.0 33.00 200.0 800.0
HFPAD 6R/L-60-T14-JHP 6.00 14.00 4.50 6.80 40.50 24.0 33.00 60.0 100.0
HFPAD 6R/L-100-T20-JHP 6.00 20.00 4.50 6.80 45.50 24.0 33.00 100.0 200.0
HFPAD 6R/L-200-T20-JHP 6.00 20.00 4.50 7.10 45.50 24.0 33.00 200.0 3000.0

I N C H
Designation CW CDX WF WB OAL HF OAH DAXN(1) DAXX(2)
HFPAD 3R/L-40-T10-JHP .118 .394 .189 .228 1.555 .945 1.299 1.57 2.56
HFPAD 3R/L-115-T18-JHP .118 .709 .189 .228 1.713 .945 1.299 4.53 15.75
HFPAD 3R/L-65-T18-JHP .118 .709 .189 .228 1.713 .945 1.299 2.56 4.53
HFPAD 4R/L-44-T14-JHP .157 .551 .189 .228 1.594 .945 1.299 1.73 2.28
HFPAD 4R/L-58-T14-JHP .157 .551 .189 .228 1.594 .945 1.299 2.28 3.46
HFPAD 4R/L-88-T14-JHP .157 .551 .177 .228 1.594 .945 1.299 3.46 6.89
HFPAD 4R/L-175-T20-JHP .157 .787 .189 .256 1.791 .945 1.299 6.89 31.50
HFPAD 5R/L-110-T14-JHP .197 .551 .177 .248 1.791 .945 1.299 4.33 7.87
HFPAD 5R/L-40-T14-JHP .197 .551 .177 .248 1.594 .945 1.299 1.57 1.97
HFPAD 5L-50-T14-JHP .197 .551 .177 .248 1.594 .945 1.299 1.97 2.95
HFPAD 5R/L-75-T14-JHP .197 .551 .177 .248 1.594 .945 1.299 2.95 4.33
HFPAD 5R/L-200-T20-JHP .197 .787 .177 .260 1.791 .945 1.299 7.87 31.50
HFPAD 6R/L-60-T14-JHP .236 .551 .177 .268 1.594 .945 1.299 2.36 3.94
HFPAD 6R/L-100-T20-JHP .236 .787 .177 .268 1.791 .945 1.299 3.94 7.87
HFPAD 6R/L-200-T20-JHP .236 .787 .177 .280 1.791 .945 1.299 7.87 118.11
• WF(assembly)=WF(shank) + WF(adapter) • HGN,GRIP,DGN inserts can be used only with right-hand adapters, HGPL inserts with left-hand adapters
• For user guide, see pages 161-173
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter

For inserts, see pages: DGN-MF (80) • DGN-W (81) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72)
• GRIPA (73) • GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)
For holders, see pages: C#-MAHD-JHP (140) • C#-MAHPD-JHP (141) • IH-HFPAD (59) • MAHPR/L-JHP (154) • MAHPR/L-XL-JHP (155)
• MAHR/L-JHP (157) • MAHR/L-JHP-MC (158)

48 ISCAR
 FACE GROOVE-TURN
Holder: MAHPL Holder: MAHR
CDX
HFPAD-3
OAH
Adapters for Face Machining WF(assembly) HF
DAXN-DAXX
OAL D
WF (adapter)
OHN

WB_2
CW Left-hand shown

M E T R I C
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 3R/L-25-T10 25.0 30.0 3.00 10.00 15.0 4.80 5.8 39.50 24.0 32.0
HFPAD 3R/L-30-T10 30.0 40.0 3.00 10.00 15.0 4.80 5.8 39.50 24.0 32.0
HFPAD 3R/L-40-T10 40.0 65.0 3.00 10.00 15.0 4.80 5.8 39.50 24.0 32.0
HFPAD 3R/L-65-T18 65.0 115.0 3.00 18.00 19.0 4.80 5.8 43.50 24.0 32.0
HFPAD 3R/L-115-T18 115.0 400.0 3.00 18.00 19.0 4.80 5.8 43.50 24.0 32.0

I N C H
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 3R/L-25-T10 .98 1.18 .118 .394 .591 .189 .228 1.555 .945 1.260
HFPAD 3R/L-30-T10 1.18 1.57 .118 .394 .591 .189 .228 1.555 .945 1.260
HFPAD 3R/L-40-T10 1.57 2.56 .118 .394 .591 .189 .228 1.555 .945 1.260
HFPAD 3R/L-65-T18 2.56 4.53 .118 .709 .748 .189 .228 1.713 .945 1.260
HFPAD 3R/L-115-T18 4.53 15.75 .118 .709 .748 .189 .228 1.713 .945 1.260
• WF(assembly)=WF(shank) + WF(adapter) • HGN & GRIP 3.. inserts can be used only with right-hand adapters, HGPL 3.. inserts with left-hand adapters
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Minimum overhang
(4) WF(adapter)

For inserts, see pages: GRIP (70) • GRIPA (73) • GRIPA (full radius) (74) • GRIP (full radius) (72) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)
For holders, see pages: C#-MAHD-JHP (140) • C#-MAHPD-JHP (141) • IH-HFPAD (59) • MAHR/L-JHP-MC (158) • MAHPR/L-JHP (154)
• MAHR/L-JHP (157) • MAHR/L (156) • MAHPR/L (153) • C#-MAHD (139) • C#-MAHPD (141) • C#-MAHDR-45 (138) • C#-MAHDOR (139)
• HSK A63WH-MAHUR/L (148) • HSK A63WH-MAHDR-45 (147) • HSK A63WH-MAHDOR (147) • IM-MAHD (150) • IM-MAHPD (151)

Holder: MAHPL Holder: MAHR

CDX
HFPAD-4
OAH
Adapters for Face Machining WF(assembly) HF
DAXN-DAXX
OAL D
WF (adapter)
OHN
WB_2
CW
Left-hand shown

M E T R I C
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 4R/L-25-T10 25.0 31.0 4.00 10.00 16.0 4.50 5.8 40.50 24.0 32.0
HFPAD 4R/L-31-T10 31.0 44.0 4.00 10.00 16.0 4.50 5.8 40.50 24.0 32.0
HFPAD 4R/L-44-T14 44.0 58.0 4.00 14.00 16.0 4.50 5.8 40.50 24.0 32.0
HFPAD 4R/L-58-T14 58.0 88.0 4.00 14.00 16.0 4.50 5.8 40.50 24.0 32.0
HFPAD 4R/L-88-T14 88.0 175.0 4.00 14.00 16.0 4.50 5.8 40.50 24.0 32.0
HFPAD 4R/L-175-T20 175.0 800.0 4.00 20.00 21.0 4.50 6.5 45.50 24.0 32.0

I N C H
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 4R/L-25-T10 .98 1.22 .157 .394 .630 .177 .228 1.594 .945 1.260
HFPAD 4R/L-31-T10 1.22 1.73 .157 .394 .630 .177 .228 1.594 .945 1.260
HFPAD 4R/L-44-T14 1.73 2.28 .157 .551 .630 .177 .228 1.594 .945 1.260
HFPAD 4R/L-58-T14 2.28 3.46 .157 .551 .630 .177 .228 1.594 .945 1.260
HFPAD 4R/L-88-T14 3.46 6.89 .157 .551 .630 .177 .228 1.594 .945 1.260
HFPAD 4R/L-175-T20 6.89 31.50 .157 .787 .827 .177 .256 1.791 .945 1.260
• WF(assembly)=WF(shank) + WF(adapter) • DGN & GRIP 4.. inserts can be used only with right-hand adapters, HGPL 4.. inserts with left-hand adapters
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Minimum overhang
(4) WF(adapter)

For inserts, see pages: DGN-MF (80) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72)
• HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)
For holders, see pages: C#-MAHD-JHP (140) • C#-MAHPD-JHP (141) • IH-HFPAD (59) • MAHR/L-JHP-MC (158) • MAHPR/L-JHP (154)
• MAHR/L-JHP (157) • MAHR/L (156) • MAHPR/L (153) • C#-MAHD (139) • C#-MAHPD (141) • C#-MAHDR-45 (138) • C#-MAHDOR (139)
• HSK A63WH-MAHUR/L (148) • HSK A63WH-MAHDR-45 (147) • HSK A63WH-MAHDOR (147) • IM-MAHD (150) • IM-MAHPD (151)

49
FACE GROOVE-TURN
Holder: MAHPL Holder: MAHR
CDX
HFPAD-5
OAH
Adapters for Face Machining WF(assembly) HF
DAXN-DAXX
OAL D
WF (adapter)
OHN
WB_2
CW
Left-hand shown

M E T R I C
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 5R/L-40-T14 40.0 50.0 5.00 14.00 16.0 4.50 6.3 40.50 24.0 32.0
HFPAD 5R/L-50-T14 50.0 75.0 5.00 14.00 16.0 4.50 6.3 40.50 24.0 32.0
HFPAD 5R/L-75-T14 75.0 110.0 5.00 14.00 16.0 4.50 6.3 40.50 24.0 32.0
HFPAD 5R/L-110-T14 110.0 200.0 5.00 14.00 16.0 4.50 6.3 40.50 24.0 32.0
HFPAD 5R/L-200-T20 200.0 800.0 5.00 20.00 21.0 4.50 6.6 45.50 24.0 32.0

I N C H
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 5R/L-40-T14 1.57 1.97 .197 .551 .630 .177 .248 1.594 .945 1.260
HFPAD 5R/L-50-T14 1.97 2.95 .197 .551 .630 .177 .248 1.594 .945 1.260
HFPAD 5R/L-75-T14 2.95 4.33 .197 .551 .630 .177 .248 1.594 .945 1.260
HFPAD 5R/L-110-T14 4.33 7.87 .197 .551 .630 .177 .248 1.594 .945 1.260
HFPAD 5R/L-200-T20 7.87 31.50 .197 .787 .827 .177 .260 1.791 .945 1.260
• WF(assembly)=WF(shank) + WF(adapter) • DGN & GRIP 5.. inserts can be used only with right-hand adapters, HGPL 5.. inserts with left-hand adapters
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Minimum overhang
(4) WF(adapter)

For inserts, see pages: GRIPA (73) • GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72)
• DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)
For holders, see pages: C#-MAHD-JHP (140) • C#-MAHPD-JHP (141) • IH-HFPAD (59) • MAHR/L-JHP-MC (158) • MAHPR/L-JHP (154)
• MAHR/L-JHP (157) • MAHR/L (156) • MAHPR/L (153) • C#-MAHD (139) • C#-MAHDOR (139) • C#-MAHPD (141) • C#-MAHDR-45 (138)
• HSK A63WH-MAHUR/L (148) • HSK A63WH-MAHDR-45 (147) • HSK A63WH-MAHDOR (147) • IM-MAHD (150) • IM-MAHPD (151)

Holder: MAHPL Holder: MAHR

CDX
HFPAD-6
OAH
Adapters for Face Machining WF(assembly) HF
DAXN-DAXX
OAL D
WF (adapter)
OHN
WB_2
CW
Left-hand shown

M E T R I C
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 6R/L-60-T14 60.0 100.0 6.00 14.00 16.0 4.50 6.8 40.50 24.0 32.0
HFPAD 6R/L-100-T20 100.0 200.0 6.00 20.00 21.0 4.50 6.8 45.50 24.0 32.0
HFPAD 6R/L-200-T20 200.0 3000.0 6.00 20.00 21.0 4.50 7.1 45.50 24.0 32.0

I N C H
Designation DAXN(1) DAXX(2) CW CDX OHN(3) WF(4) WB_2 OAL HF OAH
HFPAD 6R/L-60-T14 2.36 3.94 .236 .551 .630 .177 .268 1.594 .945 1.260
HFPAD 6R/L-100-T20 3.94 7.87 .236 .787 .827 .177 .268 1.791 .945 1.260
HFPAD 6R/L-200-T20 7.87 118.11 .236 .787 .827 .177 .280 1.791 .945 1.260
• WF(assembly)=WF(shank) + WF(adapter) • DGN & GRIP 6.. inserts can be used only with right-hand adapters, HGPL 6.. inserts with left-hand adapters
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Minimum overhang
(4) WF(adapter)

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • HGPL (75)
For holders, see pages: C#-MAHD-JHP (140) • C#-MAHPD-JHP (141) • IH-HFPAD (59) • MAHR/L-JHP-MC (158) • MAHPR/L-JHP (154)
• MAHR/L-JHP (157) • MAHR/L (156) • MAHPR/L (153) • C#-MAHD (139) • C#-MAHPD (141) • C#-MAHDR-45 (138) • C#-MAHDOR (139)
• HSK A63WH-MAHUR/L (148) • HSK A63WH-MAHDR-45 (147) • HSK A63WH-MAHDOR (147) • IM-MAHD (150) • IM-MAHPD (151)

50 ISCAR
 FACE GROOVE-TURN
CW
CDX
HFFR/L-T
L
Blades for Face Machining
DAXN-DAXX HF H
R
OAL WB_2
150°
Right-hand shown

M E T R I C

Designation CW DAXN(2) DAXX(3) CDX OAL HF H WB_2

HFFR/L 48-4T25 (1) 4.00 48.0 60.0 25.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 60-4T25 4.00 60.0 75.0 25.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 75-4T30 4.00 75.0 140.0 30.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 140-4T30 4.00 140.0 1500.0 30.00 150.00 24.8 32.0 3.2 EDG 33B*
HFFR/L 70-5T32 5.00 70.0 95.0 32.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 95-5T35 5.00 95.0 130.0 35.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 130-5T38 5.00 130.0 180.0 38.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 180-5T38 5.00 180.0 1500.0 38.00 150.00 24.8 32.0 4.0 EDG 33B*
HFFR/L 90-6T32 6.00 90.0 180.0 32.00 150.00 24.8 32.0 5.2 EDG 33B*
HFFR/L 180-6T38 6.00 180.0 400.0 38.00 150.00 24.8 32.0 5.2 EDG 33B*

I N C H

Designation CW DAXN(2) DAXX(3) CDX OAL HF H WB_2

HFFR/L 48-4T25 (1) .157 1.89 2.36 .984 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 60-4T25 .157 2.36 2.95 .984 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 75-4T30 .157 2.95 5.51 1.181 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 140-4T30 .157 5.51 59.06 1.181 5.906 .976 1.260 .126 EDG 33B*
HFFR/L 70-5T32 .197 2.76 3.74 1.260 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 95-5T35 .197 3.74 5.12 1.378 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 130-5T38 .197 5.12 7.09 1.496 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 180-5T38 .197 7.09 59.06 1.496 5.906 .976 1.260 .157 EDG 33B*
HFFR/L 90-6T32 .236 3.54 7.09 1.260 5.906 .976 1.260 .205 EDG 33B*
HFFR/L 180-6T38 .236 7.09 15.75 1.496 5.906 .976 1.260 .205 EDG 33B*
• After initial groove, no limitation to widening groove outward or toward center.
• DGN & GRIP inserts can be used only with right-hand adapters, HGPL inserts with left-hand blades
• For user guide, see pages 161-173
(1) HGPL 4...Y with LH blade
(2) Minimum penetration diameter
(3) Maximum penetration diameter

* Optional, should be ordered separately

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)
For holders, see pages: SGTBF (136) • SGTBU/SGTBN (133) • UBHCR/L (135)

Coolant Outlet

HAR/L
HFAEL
Face Machining Adapter Holders H HF Adapter

OAL OAW
B

Right-hand shown

M E T R I C

Designation OAL B H HF OAW

HAR/L 25C 110.00 25.0 25.0 25.0 39.00 SR 14-519 T-20/3
HAR/L 32C 130.00 32.0 32.0 32.0 46.00 SR 14-519 T-20/3

I N C H

Designation OAL B H HF OAW

HAR/L 25.4C 5.500 1.000 1.000 1.000 1.550 SR 14-519 T-20/3
HAR/L 31.7C 6.300 1.250 1.250 1.250 1.800 SR 14-519 T-20/3

• Holders for adapters HFAER/L & HGAER/L, HFAIR/L & HGAIR/L

For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

51
FACE GROOVE-TURN
Coolant Outlet

HAPR/L
Face Machining Perpendicular H HF HFAEL
Adapter
Holders for Adapters B OAL

Left-hand shown

M E T R I C

Designation OAL H HF B
HAPR/L 25C 124.00 25.0 25.0 25.0 SR 14-519 T-20/3
HAPR/L 32C 139.00 32.0 32.0 32.0 SR 14-519 T-20/3

I N C H

Designation OAL H HF B
HAPR/L 25.4C 4.880 1.000 1.000 1.000 SR 14-519 T-20/3
HAPR/L 31.7C 5.670 1.250 1.250 1.250 SR 14-519 T-20/3
• Holders for adapters HFAER/L & HGAER/L, HFAIR/L & HGAIR/L.
For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

HGAER/L-3 OHX CW
Adapters for External
Facing Along Shafts DAXN-DAXX

CDX OAL WF

Right-hand shown

M E T R I C
Designation CDX CW DAXN(1) DAXX(2) OHX(3) WF OAL
HGAER/L 12-3M 2.00 3.00 12.0 500.0 21.0 10.2 55.00
HGAER/L 12-3T6 6.00 3.00 12.0 15.0 21.0 10.2 55.00
HGAER/L 14-3T7 7.00 3.00 14.0 17.0 21.0 10.2 55.00
HGAER/L 17-3T8 8.00 3.00 17.0 21.0 21.0 10.2 55.00
HGAER/L 21-3T9 9.00 3.00 21.0 25.0 21.0 10.2 55.00

I N C H
Designation CDX CW DAXN(1) DAXX(2) OHX(3) WF OAL
HGAER/L 12-3M .079 .118 .47 19.69 .827 .402 2.165
HGAER/L 12-3T6 .236 .118 .47 .59 .827 .402 2.165
HGAER/L 14-3T7 .276 .118 .55 .67 .827 .402 2.165
HGAER/L 17-3T8 .315 .118 .67 .83 .827 .402 2.165
HGAER/L 21-3T9 .354 .118 .83 .98 .827 .402 2.165
• GRIP 3... inserts can be used with right-hand adapters only, HGPL 3 with left-hand adapters • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Maximum overhang

For inserts, see pages: GRIP (70) • GRIP (full radius) (72) • HGPL (75)
For holders, see pages: C#-HAD (144) • C#-HAPR/L (144) • HAPR/L (52) • HAR/L (51) • IM-HAD (152) • IM-HAPR/L (152)

Spare Parts

Designation
HGAER/L-3 SR 16-236 P T-15/3

52 ISCAR
 FACE GROOVE-TURN
HFAER/L-4 OHX CW
Adapters for External
Facing Along Shafts DAXN-DAXX

CDX OAL WF

Right-hand shown

M E T R I C

Designation CDX CW DAXN(1) DAXX(2) OAL OHX(3) WF

HFAER/L 40-4T20 20.00 4.00 40.0 48.0 68.50 21.0 11.6 SR M5X16 DIN912 HW 4.0
HFAER/L 48-4T20 20.00 4.00 48.0 60.0 68.50 21.0 11.6 SR M5X16 DIN912 HW 4.0
HFAER/L 60-4T25 25.00 4.00 60.0 75.0 68.50 26.0 11.6 SR M5X16 DIN912 HW 4.0
HFAER/L 75-4T25 25.00 4.00 75.0 100.0 68.50 26.0 11.6 SR M5X16 DIN912 HW 4.0

I N C H

Designation CDX CW DAXN(1) DAXX(2) OAL OHX(3) WF

HFAER/L 40-4T20 .787 .157 1.57 1.89 2.697 .827 .457 SR M5X16 DIN912 HW 4.0
HFAER/L 48-4T20 .787 .157 1.89 2.36 2.697 .827 .457 SR M5X16 DIN912 HW 4.0
HFAER/L 60-4T25 .984 .157 2.36 2.95 2.697 1.024 .457 SR M5X16 DIN912 HW 4.0
HFAER/L 75-4T25 .984 .157 2.95 3.94 2.697 1.024 .457 SR M5X16 DIN912 HW 4.0
• DGN & GRIP inserts can be used only with right-hand adapters, HGPL inserts with left-hand blades • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Maximum overhang

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • HGPL (75)
For holders, see pages: C#-HAD (144) • C#-HAPR/L (144) • HAPR/L (52) • HAR/L (51) • IM-HAD (152) • IM-HAPR/L (152)

HFAER/L-5T, 6T CW
Adapters for External
Facing Along Shafts DAXN-DAXX

CDX OAL WF
Right-hand shown

M E T R I C

Designation CW CDX DAXN(1) DAXX(2) OAL WF

HFAER/L 70C-5T25 5.00 25.00 70.0 95.0 66.00 12.2 EDG 33B*
HFAER/L 95C-5T25 5.00 25.00 95.0 130.0 66.00 12.2 EDG 33B*
HFAER/L 70C-6T28 6.00 28.00 70.0 100.0 69.00 12.3 EDG 33B*
HFAER/L 100C-6T32 6.00 32.00 100.0 180.0 73.00 12.3 EDG 33B*
HFAER/L 180C-6T32 6.00 32.00 180.0 400.0 73.00 12.3 EDG 33B*

I N C H

Designation CW CDX DAXN(1) DAXX(2) OAL WF

HFAER/L 70C-5T25 .197 .984 2.76 3.74 2.598 .480 EDG 33B*
HFAER/L 95C-5T25 .197 .984 3.74 5.12 2.598 .480 EDG 33B*
HFAER/L 70C-6T28 .236 1.102 2.76 3.94 2.717 .484 EDG 33B*
HFAER/L 100C-6T32 .236 1.260 3.94 7.09 2.874 .484 EDG 33B*
HFAER/L 180C-6T32 .236 1.260 7.09 15.75 2.874 .484 EDG 33B*
• After initial groove, no limitation to widening groove outward from or toward center • Adapters can be mounted on standard HAR/L, HAPR/L, HAI holders for external
machining
• DGN & GRIP inserts can be used only with right-hand adapters, HGPL inserts with left-hand blades • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

* Optional, should be ordered separately

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)
For holders, see pages: C#-HAD (144) • C#-HAPR/L (144) • HAPR/L (52) • HAR/L (51) • IM-HAD (152) • IM-HAPR/L (152)

53
FACE GROOVE-TURN
LH
HFHR/L-M
HF H OAH
Toolholders for Shallow
DAXN-DAXX
Face Grooving CWN-CWX CDX OAW

CDX
WF B
OAL Right-hand shown

M E T R I C

Designation CWN(1) CWX(2) CDX WF H HF B OAL DAXN(3) DAXX(4) OAH OAW

HFHR/L 20M 3.00 6.00 5.30 20.00 20.0 20.0 20.0 130.00 20.0 2000.0 29.0 22.50 SR M6X16 DIN912 HW 5.0
HFHR/L 25M 3.00 6.00 5.30 25.00 25.0 25.0 25.0 150.00 20.0 2000.0 34.0 27.50 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) Minimum penetration diameter
(4) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

HFHR/L- o M & HFHPR/L- o M CWX=6 mm Insert initial face grooving range

Integral Toolholders DAXN-DAXX
CW DAXN-DAXX
For shallow machining up to max. 5 mm depth of groove. CW DAXN DAXX
3 25.6 51.5
One toolholder can be mounted with inserts in 3-6 mm DAXN-DAXX
4 24.1 73.7
widths. The initial major diameter groove is limited by the CWN=3 mm 5 22.1 170
insert’s geometry of each size. 6 20.8 ∞
After the initial groove, face recessing outward or toward
the center is not limited by the insert’s geometry.

LH
HFHR/L-M
H H OAH
Toolholders for Shallow
DAXN-DAXX
Face Grooving CWN-CWX CDX OAW

CDX
WF B
OAL Right-hand shown

I N C H

Designation CWN(1) CWX(2) CDX WF H B OAL LH DAXN(3) DAXX(4) OAH OAW

HFHR 19M .118 .236 .209 .750 .750 .750 5.000 1.420 .79 78.74 1.10 .850 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4M .118 .236 .209 1.000 1.000 1.000 6.000 1.420 .79 78.74 1.35 1.100 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) Minimum penetration diameter
(4) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

HFHR/L-M & HFHPR/L-M CWX=.236” Insert initial face grooving range

Integral Toolholders DAXN-DAXX
CW
For shallow machining to max. .209” depth of groove.
DAXN-DAXX
DAXX DAXN CW
One toolholder can be mounted with inserts in .118-.236” widths. DAXN-DAXX 2.362 .945 .117
The initial major diameter groove is limited by the insert geometry 3.543 .906 .157
11.811 .827 .197
in each size. CWN=.118”
∞ .787 .236
After initial groove, face recessing outward or toward
center is not limited by insert geometry.

54 ISCAR
 FACE GROOVE-TURN
HFHPR/L-M H HF OAH
Perpendicular Toolholders
DAXN-DAXX 25
for Shallow Face Grooving
WF B
CDX
CWN-CWX CDX
OAL
Right-hand shown

M E T R I C

Designation CWN(1) CWX(2) CDX WF H B OAL DAXN(3) DAXX(4) OAH HF

HFHPR/L 20M 3.00 6.00 5.00 25.30 20.0 20.0 130.00 20.0 2000.0 29.0 20.0 SR M6X16 DIN912 HW 5.0
HFHPR/L 25M 3.00 6.00 5.00 30.30 25.0 25.0 150.00 20.0 2000.0 34.0 25.0 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) Minimum penetration diameter
(4) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

HFHPR/L-M H H OAH
Perpendicular Toolholders
DAXN-DAXX .98
for Shallow Face Grooving
WF B
CDX
CWN-CWX CDX
OAL
Right-hand shown

I N C H

Designation CWN(1) CWX(2) CDX WF H B OAL DAXN(3) DAXX(4) OAH

HFHPR/L 19M .118 .236 .197 .960 .750 .750 5.000 .95 78.74 1.10 SR M6X16 DIN912 HW 5.0
HFHPR/L 25.4M .118 .236 .197 1.220 1.000 1.000 6.000 .95 78.74 1.35 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) Minimum penetration diameter
(4) Maximum penetration diameter

For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

55
 USER GUIDE
FACE GROOVE-TURN

Boring Bars for Adapters

HGAIR/L & HFAIR/L Adapters and HAI Holders Coolant System

Adapter clamped on HAI round shank holders can Coolant Inlet
machine deep internal boring and grooving applications.
The tool can bore down to the bottom, and is supplied
(1)
with internal coolant for better performance.
Connector
Seal HAI HGAIR/L
HFAIR/L

Seal

HFAIR/L &
HAI Holders
HGAIR/L
Connector

Seal
Exchangeable for adapters, see page 60
adapters, see pages
57,60

HFAIR/L HGAIR/L - C - T-

Max.
HELIFACE Min. initial Connector for coolant inlet BSP 1/8 thread. For PL-20, use M6 thread.
(1)
Internal Insert depth
Internal adapters groove Connector not supplied with tools.
coolant width of
right or left diameter
groove

HAI Holder System Assembly

HFAIL & HGAIL HFAIR & HGAIR

Left-hand Adapters Right-hand Adapters
The same HAI boring bar can be used with right- and
left-hand adapters in a wide range of face machining
applications. The two screws and the central guiding slot
on the adapter correspond to the key and holes on the
holder ensuring strong, safe, and accurate clamping.

56 ISCAR
 FACE GROOVE-TURN
CDX
HGAIR/L-3
Adapters for Internal Face
Grooving and Turning DAXN-DAXX

CW OHX
OAL WF
Right-hand shown

M E T R I C

Designation CDX DAXN(1) DAXX(2) CW OAL WF OHX(3)

HGAIR/L 12-3M 2.00 12.0 500.0 3.00 55.00 10.2 21.0 SR 16-236 P T-15/3
HGAIR/L 12-3T6 6.00 12.0 15.0 3.00 55.00 10.2 21.0 SR 16-236 P T-15/3
HGAIR/L 14-3T7 7.00 14.0 17.0 3.00 55.00 10.2 21.0 SR 16-236 P T-15/3
HGAIR/L 17-3T8 8.00 17.0 21.0 3.00 55.00 10.2 21.0 SR 16-236 P T-15/3
HGAIR/L 21-3T9 9.00 21.0 25.0 3.00 55.00 10.2 21.0 SR 16-236 P T-15/3
HGAIR/L 25-3T9 9.00 25.0 34.0 3.00 55.00 10.2 21.0 SR 16-236 P T-15/3
HGAIR/L 35-3T10 10.00 35.0 45.0 3.00 56.00 10.3 22.0 SR 16-236 P T-15/3
HGAIR/L 45-3T10 10.00 45.0 65.0 3.00 56.00 10.3 22.0 SR 16-236 P T-15/3
HGAIR/L 65-3T18 18.00 65.0 115.0 3.00 64.00 11.3 30.0 SR 16-236 P T-15/3
HGAIR/L 115-3T18 18.00 115.0 400.0 3.00 64.00 11.3 30.0 SR 16-236 P T-15/3

I N C H

Designation CDX DAXN(1) DAXX(2) CW OAL WF OHX(3)

HGAIR/L 12-3M .079 .47 19.69 .118 2.165 .402 .827 SR 16-236 P T-15/3
HGAIR/L 12-3T6 .236 .47 .59 .118 2.165 .402 .827 SR 16-236 P T-15/3
HGAIR/L 14-3T7 .276 .55 .67 .118 2.165 .402 .827 SR 16-236 P T-15/3
HGAIR/L 17-3T8 .315 .67 .83 .118 2.165 .402 .827 SR 16-236 P T-15/3
HGAIR/L 21-3T9 .354 .83 .98 .118 2.165 .402 .827 SR 16-236 P T-15/3
HGAIR/L 25-3T9 .354 .98 1.34 .118 2.165 .402 .827 SR 16-236 P T-15/3
HGAIR/L 35-3T10 .394 1.38 1.77 .118 2.205 .406 .866 SR 16-236 P T-15/3
HGAIR/L 45-3T10 .394 1.77 2.56 .118 2.205 .406 .866 SR 16-236 P T-15/3
HGAIR/L 65-3T18 .709 2.56 4.53 .118 2.520 .445 1.181 SR 16-236 P T-15/3
HGAIR/L 115-3T18 .709 4.53 15.75 .118 2.520 .445 1.181 SR 16-236 P T-15/3
• HGN & GRIP 3.. inserts can be used only with right-hand adapters, HGPL 3.. inserts with left-hand adapters • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Maximum overhang

For inserts, see pages: GRIPA (73) • GRIPA (full radius) (74) • GRIP (70) • GRIP (full radius) (72) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)
For holders, see pages: C#-HAD (144) • C#-HAPR/L (144) • HAI-C (60) • HAPR/L (52) • HAR/L (51) • IH-HFAIR (58) • IM-HAD (152) • IM-HAPR/L (152)

57
FACE GROOVE-TURN
A OAL View A
IH-HFAIR
Intermediate Serrated Cartridge OAW
for standard HELI-FACE HFAIR OAH
Adapters

M E T R I C
Designation OAH OAW OAL
IH-HFAIR 55.40 72.50 44.90
For tools, see pages: HFAIR/L-DG (61) • HGAIR/L-3 (57)

HSK63 HATA+IH-HFAIR
C6 HATA+IH-HFAIR HSK63/C6 HATA

DAX CW
IH-HFAIR

CDX

Adapter

Adapters CW (min) CW (max) CDX DAX (min) DAX (max)

HGAIR 12-3M 3 5.1 2 83.8 123.4
HGAIR 65-3T18 3 5.1 18 86 115
HGAIR 115-3T18 3 5.1 18 115 125.6
HFAIR 75C-4T30DG 4 6.9 30 85.2 124.8
HFAIR 70C-5T25DG 5 8.1 25 87.2 95
HFAIR 95C-5T35DG 5 8.1 35 95 126.8
HFAIR 70C-6T28DG 6 10.1 28 87.4 100
HFAIR 100C-6T32DG 6 10.1 32 100 127

Spare Parts

Designation
IH-HFAIR SR 14-519 T-20/3 O-RING 19X2 NBR SR M6X20-XT

58 ISCAR
 FACE GROOVE-TURN
A View A
OAL
IH-HFPAD
Intermediate Serrated Cartridge
for Standard HFPAD R Adapters OAW
OAH

M E T R I C
Designation OAH OAW OAL
IH-HFPAD 54.00 73.00 58.90
For tools, see pages: HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48)

HSK63 HATA+IH-HFPAD
C6 HATA+IH-HFPAD HSK63/C6 HATA

DAX CW
IH-HFPAD

CDX

Adapter

Adapters CW (min) CW (max) CDX DAX (min) DAX (max)

HFPAD 3R-25-T10 3 5.1 10 25 30
HFPAD 3R-30-T10 3 5.1 10 30 40
HFPAD 3R-40-T10 3 5.1 10 40 65
HFPAD 3R-65-T18 3 5.1 18 65 99.2
HFPAD 4R-25-T10 4 6.9 10 25 31
HFPAD 4R-31-T10 4 6.9 10 31 44
HFPAD 4R-44-T14 4 6.9 14 44 58
HFPAD 4R-58-T14 4 6.9 14 58 88
HFPAD 4R-88-T14 4 6.9 14 88 100.8
HFPAD 5R-40-T14 5 8.1 14 40 50
HFPAD 5R-50-T14 5 8.1 14 50 75
HFPAD 5R-75-T14 5 8.1 14 75 101.8
HFPAD 6R-60-T14 6 10.1 14 60 100
HFPAD 6R-100-T20 6 10.1 20 100 102.8
HFPAD 3R-30-T10-JHP 3 5.1 10 30 40
HFPAD 3R-40-T10-JHP 3 5.1 10 40 65
HFPAD 3R-65-T18-JHP 3 5.1 18 65 99.2
HFPAD 4R-44-T14-JHP 4 6.9 14 44 58
HFPAD 4R-58-T14-JHP 4 6.9 14 58 88
HFPAD 4R-88-T14-JHP 4 6.9 14 88 100.8
HFPAD 5R-40-T14-JHP 5 8.1 14 40 50
HFPAD 5R-75-T14-JHP 5 8.1 14 75 101.8
HFPAD 6R-60-T14-JHP 6 10.1 14 60 100
HFPAD 6R-100-T20-JHP 6 10.1 20 100 102.8

Spare Parts

Designation
IH-HFPAD SR M6X20-XT SR M5-04451 SR M6X12DIN6912 HW 5.0 T-20/5 O-RING 19X2 NBR OR 5X1N BLD T20/M7 SW6-SD

59
FACE GROOVE-TURN
CDX
HFAIR/L-4
Adapters for Internal Face
Grooving and Turning DAXN-DAXX

CW OHX
OAL WF
Right-hand shown

M E T R I C

Designation CDX CW DAXN(1) DAXX(2) OAL WF OHX(3)

HFAIR/L 34-4T18 18.00 4.00 34.0 40.0 67.00 15.3 33.0 SR M5X16 DIN912 HW 4.0
HFAIR/L 40-4T20 20.00 4.00 40.0 48.0 67.00 15.3 33.0 SR M5X16 DIN912 HW 4.0
HFAIR/L 48-4T20 20.00 4.00 48.0 60.0 67.00 15.3 33.0 SR M5X16 DIN912 HW 4.0
HFAIR/L 60-4T25 25.00 4.00 60.0 75.0 67.00 15.3 33.0 SR M5X16 DIN912 HW 4.0

I N C H

Designation CDX CW DAXN(1) DAXX(2) OAL WF OHX(3)

HFAIR/L 34-4T18 .709 .157 1.34 1.57 2.638 .602 1.299 SR M5X16 DIN912 HW 4.0
HFAIR/L 40-4T20 .787 .157 1.57 1.89 2.638 .602 1.299 SR M5X16 DIN912 HW 4.0
HFAIR/L 48-4T20 .787 .157 1.89 2.36 2.638 .602 1.299 SR M5X16 DIN912 HW 4.0
HFAIR/L 60-4T25 .984 .157 2.36 2.95 2.638 .602 1.299 SR M5X16 DIN912 HW 4.0
• DGN & GRIP inserts can be used only with right-hand adapters, HGPL inserts with left-hand blades • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Maximum overhang

For inserts, see pages: DGN-MF (80) • GRIPA (73) • GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70)
• GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • HGPL (75)
For holders, see pages: C#-HAD (144) • C#-HAPR/L (144) • HAI-C (60) • HAPR/L (52) • HAR/L (51) • IM-HAD (152) • IM-HAPR/L (152)

DCONMS
CDX(a) Coolant Outlet
HAI-C OAL
Boring Bars with Coolant
Holes for Internal Grooving HF
and Turning Adapters WF (holder)
WF (adapter)
WF (assembly)=WF (adapter)+WF (holder)

M E T R I C

Designation DCONMS OAL HF WF(1) CSP(2)

HAI 20 20.00 130.00 9.0 0.50 0 SR 14-519 T-20/3
HAI 25C 25.00 150.00 11.5 3.00 1 SR 14-519 T-20/3 PL 25
HAI 32C 32.00 200.00 14.5 6.50 1 SR 14-519 T-20/3 PL 32
HAI 40C 40.00 250.00 18.0 10.50 1 SR 14-519 T-20/3 PL 40

I N C H

Designation DCONMS OAL HF WF(1) CSP(2)

HAI 19 .750 5.120 .338 .005 1 SR 14-519 T-20/3
HAI 25.4C 1.000 6.000 .460 .130 1 SR 14-519 T-20/3 PL 100
HAI 31.7C 1.250 7.874 .570 .255 1 SR 14-519 T-20/3 PL 125
HAI 38.1C 1.500 10.000 .670 .380 1 SR 14-519 T-20/3 PL 150
• The HAI boring bars can be used with right and left-hand adapters • (a) CDX - see corresponding adapters
(1) Holder
(2) 0 - Without coolant supply, 1 - With coolant supply

For tools, see pages: HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAIR/L-3 (57)

60 ISCAR
 FACE GROOVE-TURN
WF
HFAIR/L-DG
Adapters for Internal Face
Grooving and Turning DAXN-DAXX
OAL
OHX
CW CDX

Right-hand shown

M E T R I C

Designation CW DAXN(1) DAXX(2) CDX WF OHX(3) OAL

HFAIR/L 75C-4T30DG 4.00 75.0 140.0 30.00 10.9 34.5 68.50 EDG 33B*
HFAIR/L 140C-4T30DG 4.00 140.0 - 30.00 10.9 34.5 68.50 EDG 33B*
HFAIR/L 55C-5T25DG 5.00 55.0 70.0 25.00 11.9 32.0 66.00 EDG 33B*
HFAIR/L 70C-5T25DG 5.00 70.0 95.0 25.00 11.9 32.0 66.00 EDG 33B*
HFAIR/L 95C-5T35DG 5.00 95.0 130.0 35.00 11.9 39.5 73.50 EDG 33B*
HFAIR/L 130C-5T38DG 5.00 130.0 180.0 38.00 11.9 42.5 76.50 EDG 33B*
HFAIR/L 180C-5T38DG 5.00 180.0 - 38.00 11.9 42.5 76.50 EDG 33B*
HFAIR/L 70C-6T28DG 6.00 70.0 100.0 28.00 12.0 35.0 69.00 EDG 33B*
HFAIR/L 100C-6T32DG 6.00 100.0 180.0 32.00 12.0 39.0 73.00 EDG 33B*
HFAIR/L 180C-6T38DG 6.00 180.0 - 38.00 12.4 42.5 76.50 EDG 33B*
I N C H

Designation CW DAXN(1) DAXX(2) CDX WF OHX(3) OAL

HFAIR/L 75C-4T30DG .157 2.95 5.51 1.181 .429 1.358 2.697 EDG 33B*
HFAIR/L 140C-4T30DG .157 5.51 - 1.181 .429 1.358 2.697 EDG 33B*
HFAIR/L 55C-5T25DG .197 2.17 2.76 .984 .469 1.260 2.598 EDG 33B*
HFAIR/L 70C-5T25DG .197 2.76 3.74 .984 .469 1.260 2.598 EDG 33B*
HFAIR/L 95C-5T35DG .197 3.74 5.12 1.378 .469 1.555 2.894 EDG 33B*
HFAIR/L 130C-5T38DG .197 5.12 7.09 1.496 .469 1.673 3.012 EDG 33B*
HFAIR/L 180C-5T38DG .197 7.09 - 1.496 .469 1.673 3.012 EDG 33B*
HFAIR/L 70C-6T28DG .236 2.76 3.94 1.102 .472 1.378 2.717 EDG 33B*
HFAIR/L 100C-6T32DG .236 3.94 7.09 1.260 .472 1.535 2.874 EDG 33B*
HFAIR/L 180C-6T38DG .236 7.09 - 1.496 .488 1.673 3.012 EDG 33B*
• After initial groove, no limitation to widening groove outward or toward center
• DGN inserts can be used on right- and left-hand tools, GRIP inserts only on right-hand tools, HFPR/L right-hand inserts on right-hand tools (same for left-hand), and HGPL
inserts only on left-hand tools.
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) Maximum overhang

* Optional, should be ordered separately

For inserts, see pages: DGN-MF (80) • GRIPA (73) • GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70)
• GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)
For holders, see pages: C#-HAD (144) • C#-HAPR/L (144) • HAI-C (60) • HAPR/L (52) • HAR/L (51) • IH-HFAIR (58) • IM-HAD (152) • IM-HAPR/L (152)

Adapters can be used for internal machining along bore, and can be mounted on standard
HAI boring bars for internal machining and HAR/L, HAPR/L holders for external machining.

Boring, Face Grooving and Face Recessing Capacity

Boring Face Grooving Face Recessing
B Min. =WF (assembly)+G+DCONMS/2 D Min. =2WF (assembly)-B+2G+DCONMS P Min. =2WF (assembly)-B-2CW+2G+DCONMS
Bmin. G(1) Dmin. G(1) Pmin. G(1)

B B

(1) The minimum recommended value for clearance (G) is 0.5 mm

* WF (assembly)=WF(adapter)+WF(holder)

61
FACE GROOVE-TURN
DCONMS

LF
IM-HFIR-MC BDRED
Tools for Internal Grooving and WF 5.3
Turning with ISO 26622-1(*)
Tapered Shank CWN-CWX LDRED Right-hand shown

M E T R I C

Designation DCONMS LF BDRED WF LDRED CWN(1) CWX(2)

IM40 HFIR-MC 40.00 80.0 25.00 11.30 52.0 3.00 6.00 SR M5X16 DIN912 HW 4.0 EZ 83
IM50 HFIR-MC 50.00 80.0 25.00 11.30 52.0 3.00 6.00 SR M5X16 DIN912 HW 4.0 EZ 83
• (*) Tools with orientation holes in the flange groove can be supplied on request
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center • For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81)

DCONMS

LF
IM-HFIR-MC BDRED
Tools for Internal Grooving and WF .21
Turning with ISO 26622-1(*)
Tapered Shank CWN-CWX LDRED Right-hand shown

I N C H

Designation DCONMS LF BDRED WF LDRED CWN(1) CWX(2)

IM40 HFIR-MC 1.575 3.15 .984 .445 2.05 .118 .236 SR M5X16 DIN912 HW 4.0 EZ 83
IM50 HFIR-MC 1.968 3.15 .984 .445 2.05 .118 .236 SR M5X16 DIN912 HW 4.0 EZ 83
• (*) Tools with orientation holes in the flange groove can be supplied on request
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center • For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81)

62 ISCAR
 FACE GROOVE-TURN
HFIR/L-MC CDX DCONMS
Boring Bars for Internal
Grooving and Turning WF (holder)
CWN-CWX HF
OAL
CW/2

M E T R I C

Designation DCONMS CWN(1) CWX(2) CDX OAL WF HF

HFIR/L 16MC 16.00 3.00 6.00 5.00 150.00 11.14 7.5 SR M5X16 DIN912 HW 4.0 PL 16
HFIR/L 20MC 20.00 3.00 6.00 5.00 170.00 11.14 9.0 SR M5X16 DIN912 HW 4.0 PL 20
HFIR/L 25MC 25.00 3.00 6.00 5.00 200.00 11.14 11.5 SR M5X16 DIN912 HW 4.0 PL 25
HFIR/L 32MC 32.00 3.00 6.00 5.00 250.00 14.68 14.5 SR M6X20 DIN912 HW 5.0 PL 32
HFIR/L 40MC 40.00 3.00 6.00 5.00 300.00 18.70 18.0 SR M6X20 DIN912 HW 5.0 PL 40
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 56, 161-173
(1) Minimum cutting width
(2) Maximum cutting width

For inserts, see pages: DGN-MF (80) • DGN-W (81) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72)
• HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)

Boring Internal Face Grooving Internal Face Recessing

HFIR/L- o MC Integral Boring Bars
For shallow, internal face machining to max.
5 mm depth of groove. One boring bar can
be mounted with inserts in 4-6 mm widths.

The initial major diameter groove is limited by

Boring, Face Grooving & Face Recessing Capacity the insert’s geometry of each size.
Boring Face Grooving Face Recessing After the initial groove, face recessing
B Min. =WF(holder)+ D Min. =2WF (holder)+ P Min. =2WF (holder)+
DCONMS/2+CW/2+2G DCONMS+CW-B+2G DCONMS-W-B+2G
outward or toward center is not
limited by the insert’s geometry.

B D B P B
Insert Initial
Face Grooving Range
5max
D
G(1) G(1) G(1)
CW Min. Max.
4 23 90
Bmin. Dmin. B 5 21 300
Pmin. B
6 20 ∞
(1)
The minimum recommended value for clearance (G) is 0.5 mm

63
FACE GROOVE-TURN

HFIR/L-MC CDX DCONMS

Boring Bars for Internal
Grooving and Turning WF
CWN-CWX HF
OAL
CW/2

I N C H

Designation DCONMS CWN(1) CWX(2) CDX OAL WF HF

HFIR/L 15.9MC .625 .118 .236 .197 5.906 .438 .295 SR M5X16 DIN912 HW 4.0 PL 062
HFIR/L 19.05MC .750 .118 .236 .197 6.693 .438 .354 SR M5X16 DIN912 HW 4.0 PL 075
HFIR/L 25.4MC 1.000 .118 .236 .197 8.000 .450 .460 SR M5X16 DIN912 HW 4.0 PL 100
HFIR/L 31.7MC 1.250 .118 .236 .197 10.000 .570 .570 SR M6X20 DIN912 HW 5.0 PL 125
HFIR/L 38.1MC 1.500 .118 .236 .197 12.000 .700 .670 SR M6X20 DIN912 HW 5.0 PL 150
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 56, 161-173
(1) Minimum cutting width
(2) Maximum cutting width

For inserts, see pages: DGN-MF (80) • DGN-W (81) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72)
• HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)

Boring Internal Face Grooving Internal Face Recessing

HFIR/L-: MC Integral Boring Bars Insert Initial Face Grooving Range

For shallow, internal face machining to max. .197” depth of groove. D
One boring bar can be mounted with inserts of .157-.236” widths. The initial W Min. Max.
major diameter groove is limited by the insert geometry of each size.After initial
.157 .906 3.543
groove, face recessing outward or toward center is not limited by insert geometry.
.197 .827 11.81
.236 .787 ∞
Boring, Face Grooving & Face Recessing Capacity
Boring Face Grooving Face Recessing
B Min.=F+d/2+W/2+2G D Min.=2F+d+W-B+2G P Min.=2F+d-W-B+2G

D B
B P B

.197max

G(1) G(1) G(1)

Bmin. Dmin. B Pmin. B

(1)
The minimum recommended value for clearance (G) is .020”.

64 ISCAR
 FACE GROOVE-TURN
CDX 25
CR HFIR-M CW DAXN-DAXX
Cartridges for Face HF H
Min Max
DAXN-DAXX
Grooving and Turning 3 60 130
4,5,6 60 ∞
CWN-CWX WF B

CWN-CWX OAL
Right-hand shown

M E T R I C
Designation CWN(1) CWX(2) HF B H OAL WF CDX
CR HFIR-16M 3.00 6.00 16.0 16.0 20.0 67.00 20.00 5.00
CR HFIR-20M 3.00 6.00 20.0 20.0 24.0 72.00 24.00 5.00
• Used for shallow internal face machining to max. 5 mm depth of groove • Inserts in 3-6 mm widths can be mounted on the cartridges
• Only DGN & GRIP 4.. - 6.. inserts can be used with the right-hand tools
(1) Minimum cutting width
(2) Maximum cutting width

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81)

CR-HFIR/L-M
F
Assembly Dimensions E 45º
L1

R M8
Assembly
Screw

Designation E L1(1) F(2) Rmax. Assembly Screw(3)

CR HFIR/L-16M 25 8 20 6 M8X30
CR HFIR/L-20M 30 10 24 6 M8X30
(1) L adjustment±1
(2) F adjustment +0.3
-0
(3) Assembly screws ISO 7380 are recommended

Spare Parts

Designation
CR HFIR-16M SR M5X20DIN912 HW 4.0 SR 76-1401 SR M4X10 DIN916 HW 2.0
CR HFIR-20M SR M5X20DIN912 HW 4.0 SR 76-1401 SR M4X10 DIN913 HW 2.0

65
FACE GROOVE-TURN
CDX .985
CR HFIR-M
CW DAXN-DAXX H
Cartridges for Face Min Max
HF
DAXN-DAXX
Grooving and Turning .118 2.362 5.118
.157
.197 2.362 ∞ CWN-CWX WF B
.236
CWN-CWX OAL
Right-hand shown

I N C H
Designation CWN(1) CWX(2) HF B H OAL WF CDX
CR HFIR-16M .118 .236 .630 .630 .787 2.638 .787 .197
CR HFIR-20M .118 .236 .787 .787 .945 2.835 .945 .197
• Used for shallow internal face machining to max. .197" depth of groove • Inserts in .118 - .236" widths can be mounted on the cartridges
• Only DGN and GRIP .157 - .236" inserts can be used with the right-hand tools
(1) Minimum cutting width
(2) Maximum cutting width

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81)

CR HFIR/L-M
Assembly Dimensions F
E 45º
L1

R
M8
Assembly
Screw

Designation E L1(1) F(2) Rmax. Assembly Screw(3)

CR HFIR/L-16M .984 .315 .787 .236 M8X30
CR HFIR/L-20M 1.181 .394 .945 .236 M8X30
(1) L adjustment ± .04
(2) F adjustment +.012
-0
(3) Assembly screws ISO 7380 are recommended.

Spare Parts

Designation
CR HFIR-16M SR M5X20DIN912 HW 4.0 SR 76-1401 SR M4X10 DIN916 HW 2.0
CR HFIR-20M SR M5X20DIN912 HW 4.0 SR 76-1401 SR M4X10 DIN913 HW 2.0

66 ISCAR
 FACE GROOVE-TURN
±0.1
HFPN
Utility Double-Ended Face
Machining Inserts HFPN 2010 7°

CW
RE INSL

M E T R I C
Recommended
Dimensions
Machining Data

f groove

IC808
Designation CW RE CWTOL(1) RETOL(2) INSL (mm/rev)
HFPN 2002 2.00 0.20 0.04 0.030 19.40 • 0.03-0.10
HFPN 2010 2.00 1.00 0.04 0.030 19.40 • 0.03-0.10
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: HFFA (38) • HFFH (37)

±.004
HFPN
Utility Double-Ended Face
Machining Inserts HFPN 2010 7°

CW
RE INSL

I N C H
Recommended
Dimensions
Machining Data

f groove
IC808

Designation CW RE CWTOL(1) RETOL(2) INSL (IPR)

HFPN 2002 .079 .0079 .0016 .0012 .764 • .0012-.0039
HFPN 2010 .079 .0394 .0016 .0012 .764 • .0012-.0039
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: HFFA (38) • HFFH (37)

67
FACE GROOVE-TURN

±0.1 19 Ref.
HFPR/L CW
Utility Double-Ended Face
Machining Inserts DAXN-DAXX 7°

RE BW
No depth penetration limit

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f face-groove f face-turn

IC8250

IC9015

IC5010
IC830
IC354

IC808

IC806
IC20
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (mm) (mm/rev) (mm/rev)
HFPR/L 3003 3.00 0.30 0.05 0.050 2.10 25.6 51.5 • • • • • • • 0.30-1.50 0.08-0.20 0.10-0.20
HFPR/L 4004 4.00 0.40 0.05 0.050 2.80 24.1 73.7 • • • • • • • 0.40-2.00 0.10-0.24 0.15-0.25
HFPR/L 5004 5.00 0.40 0.05 0.050 3.40 22.1 170.0 • • • • • • • • 0.50-2.50 0.12-0.24 0.15-0.35
HFPR/L 6004 6.00 0.40 0.05 0.050 4.00 20.8 - • • • • • • • 0.40-3.00 0.12-0.28 0.15-0.40
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

HFPR/L ±.004 .748 Ref. CW

Utility Double-Ended Face
Machining Inserts DAXN-DAXX 7°

RE BW
No depth penetration limit

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f face-groove f face-turn
IC8250

IC9015

IC5010
IC830
IC354

IC808

IC806
IC20

Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (inch) (IPR) (IPR)

HFPR/L 3003 .118 .012 .0020 .0020 .083 1.01 2.03 • • • • • • • .012-.059 .0031-.0079 .0039-.0079
HFPR/L 4004 .157 .016 .0020 .0020 .110 .95 2.90 • • • • • • • .016-.079 .0039-.0094 .0059-.0098
HFPR/L 5004 .197 .016 .0020 .0020 .134 .87 6.69 • • • • • • • • .020-.098 .0047-.0094 .0059-.0138
HFPR/L 6004 .236 .016 .0020 .0020 .157 .82 - • • • • • • • .016-.118 .0047-.0110 .0059-.0157
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

68 ISCAR
 FACE GROOVE-TURN
±0.1
HFPR/L (full radius) 19 Ref. CW
Utility Double-Ended Full Radius
Face Machining Inserts DAXN-DAXX 7°

RE BW
No depth penetration limit.

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

f face-
ap groove f face-turn

IC8250

IC9015

IC5010
IC830
IC354

IC808

IC806
IC20
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (mm) (mm/rev) (mm/rev)
HFPR/L 3015 3.00 1.50 0.05 0.050 2.10 25.6 51.5 • • • • • • • 0.00-1.50 0.08-0.20 0.12-0.20
HFPR/L 4020 4.00 2.00 0.05 0.050 2.80 24.1 73.7 • • • • • • • 0.00-2.00 0.10-0.24 0.15-0.25
HFPL 5025 5.00 2.50 0.05 0.050 3.40 22.1 170.0 • • • • • • • 0.00-2.50 0.12-0.24 0.15-0.35
HFPR 5025 5.00 2.50 0.05 0.050 3.40 22.1 170.0 • • • • • • • 0.00-2.50 0.12-0.24 0.15-0.35
HFPR/L 6030 6.00 3.00 0.05 0.050 4.00 20.8 - • • • • • • • 0.00-3.00 0.12-0.28 0.20-0.40
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

HFPR/L (full radius) ±.004 .748 Ref. CW

Utility Double-Ended Full Radius
Face Machining Inserts DAXN-DAXX 7°

RE BW
No depth penetration limit.

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

f face-
ap groove f face-turn
IC8250

IC9015

IC5010
IC830
IC354

IC808

IC806
IC20

Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (inch) (IPR) (IPR)

HFPR/L 3015 .118 .059 .0020 .0020 .083 1.01 2.03 • • • • • • • .000-.059 .0031-.0079 .0047-.0079
HFPR/L 4020 .157 .079 .0020 .0020 .110 .95 2.90 • • • • • • • .000-.079 .0039-.0094 .0059-.0098
HFPL 5025 .197 .098 .0020 .0020 .134 .87 6.69 • • • • • • • .000-.098 .0047-.0094 .0059-.0138
HFPR 5025 .197 .098 .0020 .0020 .134 .87 6.69 • • • • • • • .000-.098 .0047-.0094 .0059-.0138
HFPR/L 6030 .236 .118 .0020 .0020 .157 .82 - • • • • • • • .000-.118 .0047-.0110 .0079-.0157
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

69
FACE GROOVE-TURN
INSL (Ref.)
GRIP ±0.1
Utility Double-Ended
RE
Inserts for External, Internal BW
and Face Machining CW

No depth penetration limit

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

f face-

IC8250

IC5010
ap f turn f groove groove f face-turn

IC830

IC808
IC908
IC418

IC806
IC807
IC804
IC08
Designation CW CWTOL(1) RE RETOL(2) INSL BW (mm) (mm/rev) (mm/rev) (mm/rev) (mm/rev)
GRIP 3002Y 3.00 0.050 0.20 0.050 15.80 2.30 • • • • • • • • 0.25-1.80 0.14-0.18 0.07-0.11 0.08-0.20 0.10-0.20
GRIP 3003Y 3.00 0.050 0.30 0.050 15.80 2.30 • • • • • • • • 0.40-1.80 0.15-0.19 0.07-0.11 0.08-0.20 0.10-0.20
GRIP 318-040Y 3.18 0.050 0.40 0.050 15.80 2.30 • • • • • 0.50-1.90 0.17-0.22 0.07-0.12 0.08-0.20 0.10-0.20
GRIP 4002Y 4.00 0.050 0.20 0.050 19.00 2.80 • • • • • • • 0.25-2.40 0.16-0.21 0.09-0.14 0.10-0.24 0.15-0.30
GRIP 4004Y 4.00 0.050 0.40 0.050 19.00 2.80 • • • • • • • • • • 0.50-2.40 0.18-0.24 0.09-0.15 0.10-0.24 0.15-0.30
GRIP 476-080Y 4.76 0.050 0.80 0.050 19.00 3.10 • • • • • • 1.00-2.80 0.21-0.33 0.10-0.20 0.10-0.24 0.15-0.30
GRIP 5005Y 5.00 0.050 0.50 0.050 19.00 3.30 • • • • • • • • • • 0.60-3.00 0.20-0.30 0.11-0.20 0.12-0.24 0.15-0.35
GRIP 5008Y 5.00 0.050 0.80 0.050 19.00 3.40 • • • • • • • • 1.00-3.00 0.23-0.35 0.11-0.21 0.12-0.24 0.15-0.35
GRIP 6005Y 6.00 0.050 0.50 0.050 19.00 4.20 • • • • • • • • 0.60-3.60 0.22-0.36 0.13-0.23 0.12-0.28 0.15-0.40
GRIP 6008Y 6.00 0.050 0.80 0.050 19.00 4.20 • • • • • • • • 1.00-3.60 0.24-0.42 0.13-0.25 0.12-0.28 0.15-0.40
GRIP 635-080Y 6.35 0.050 0.80 0.050 19.00 4.20 • • • • • 1.00-3.80 0.25-0.44 0.14-0.27 0.12-0.28 0.15-0.40
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • HGAER/L-3 (52)
• HGAIR/L-3 (57) • HGHR/L-3 (39) • IM-HFIR-MC (62)

70 ISCAR
 FACE GROOVE-TURN
INSL (Ref.)
GRIP ±.004
Utility Double-Ended
RE
Inserts for External, Internal BW
and Face Machining CW

No depth penetration limit

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

f face-

IC8250

IC5010
ap f turn f groove groove f face-turn

IC830

IC808
IC908
IC418

IC806
IC807
IC804
IC08
Designation CW CWTOL(1) RE RETOL(2) INSL BW (inch) (IPR) (IPR) (IPR) (IPR)
GRIP 3002Y .118 .00196 .0079 .0020 .622 .091 • • • • • • • • .010-.071 .0055-.0071 .0027-.0043 .0031-.0079 .0039-.0079
GRIP 3003Y .118 .00196 .0118 .0020 .622 .091 • • • • • • • • .016-.071 .0059-.0075 .0027-.0043 .0031-.0079 .0039-.0079
GRIP 318-040Y .125 .00196 .0157 .0020 .622 .091 • • • • • .020-.075 .0067-.0087 .0027-.0047 .0031-.0079 .0039-.0079
GRIP 4002Y .157 .00196 .0079 .0020 .748 .110 • • • • • • • .010-.094 .0063-.0083 .0035-.0055 .0039-.0094 .0059-.0118
GRIP 4004Y .157 .00196 .0157 .0020 .748 .110 • • • • • • • • • • .020-.094 .0071-.0094 .0035-.0059 .0039-.0094 .0059-.0118
GRIP 476-080Y .187 .00196 .0315 .0020 .748 .122 • • • • • • .039-.110 .0083-.0130 .0039-.0079 .0039-.0094 .0059-.0118
GRIP 5005Y .197 .00196 .0197 .0020 .748 .130 • • • • • • • • • • .024-.118 .0079-.0118 .0043-.0079 .0047-.0094 .0059-.0138
GRIP 5008Y .197 .00196 .0315 .0020 .748 .134 • • • • • • • • .039-.118 .0091-.0138 .0043-.0083 .0047-.0094 .0059-.0138
GRIP 6005Y .236 .00196 .0197 .0020 .748 .165 • • • • • • • • .024-.142 .0087-.0142 .0051-.0091 .0047-.0110 .0059-.0157
GRIP 6008Y .236 .00196 .0315 .0020 .748 .165 • • • • • • • • .039-.142 .0094-.0165 .0051-.0098 .0047-.0110 .0059-.0157
GRIP 635-080Y .250 .00196 .0315 .0020 .748 .165 • • • • • .039-.150 .0098-.0173 .0055-.0106 .0047-.0110 .0059-.0157
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • HGAER/L-3 (52)
• HGAIR/L-3 (57) • HGHR/L-3 (39) • IM-HFIR-MC (62)

The Twisted Insert

for Face Machining

The double-ended, twisted insert body

makes it possible to machine deeper
than the inserts’ length. A unique
chipformer for controlled chip flow in
axial and radial directions.
The rear angle is slanted in relation
to the frontal edge so it does not
come into contact with the machined
groove surface as the tool penetrates
deeply into the workpiece.

71
FACE GROOVE-TURN
INSL (Ref.)
GRIP (full radius) ±0.1
Utility Double-Ended Full
Radius Inserts for External, 7°
Internal and Face Machining CW
RE BW
No depth penetration limit

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

f face-

IC8250

IC5010
ap f turn f groove groove f face-turn

IC830

IC808
IC908
IC418

IC806
IC807
IC804
IC08
Designation CW RE CWTOL(1) RETOL(2) INSL BW (mm) (mm/rev) (mm/rev) (mm/rev) (mm/rev)
GRIP 3015Y 3.00 1.50 0.05 0.050 15.80 2.10 • • • • • • • • • • 0.00-1.50 0.18-0.26 0.07-0.13 0.08-0.20 0.10-0.20
GRIP 318-159Y 3.18 1.59 0.05 0.050 15.80 2.30 • • • 0.00-1.50 0.19-0.28 0.07-0.13 0.08-0.20 0.10-0.20
GRIP 4020Y 4.00 2.00 0.05 0.050 19.00 2.80 • • • • • • • • • • 0.00-2.00 0.20-0.34 0.09-0.17 0.10-0.24 0.15-0.30
GRIP 476-238Y 4.76 2.38 0.05 0.050 19.00 3.20 • • • • 0.00-2.30 0.21-0.40 0.10-0.20 0.10-0.24 0.15-0.30
GRIP 5025Y 5.00 2.50 0.05 0.050 19.00 3.40 • • • • • • • • 0.00-2.50 0.23-0.42 0.11-0.21 0.12-0.24 0.15-0.35
GRIP 6030Y 6.00 3.00 0.05 0.050 19.00 4.20 • • • • • • • • • 0.00-3.00 0.24-0.50 0.13-0.25 0.12-0.28 0.15-0.40
GRIP 635-318Y 6.35 3.18 0.05 0.050 19.00 4.00 • • • 0.00-3.10 0.25-0.53 0.14-0.27 0.12-0.28 0.15-0.40
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48)
• HGAER/L-3 (52) • HGAIR/L-3 (57) • HGHR/L-3 (39) • IM-HFIR-MC (62)

INSL (Ref.)
GRIP (full radius) ±.004
Utility Double-Ended Full
Radius Inserts for External, 7°
Internal and Face Machining CW
RE BW
No depth penetration limit

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

f face-
IC8250

IC5010

ap f turn f groove groove f face-turn

IC830

IC808
IC908
IC418

IC806
IC807
IC804
IC08

Designation CW RE CWTOL(1) RETOL(2) INSL BW (inch) (IPR) (IPR) (IPR) (IPR)

GRIP 3015Y .118 .059 .0020 .0020 .622 .083 • • • • • • • • • • .000-.059 .0071-.0102 .0027-.0051 .0031-.0079 .0039-.0079
GRIP 318-159Y .125 .063 .0020 .0020 .622 .091 • • • .000-.059 .0075-.0110 .0027-.0051 .0031-.0079 .0039-.0079
GRIP 4020Y .157 .079 .0020 .0020 .748 .110 • • • • • • • • • • .000-.079 .0079-.0134 .0035-.0067 .0039-.0094 .0059-.0118
GRIP 476-238Y .187 .094 .0020 .0020 .748 .126 • • • • .000-.091 .0083-.0157 .0039-.0079 .0039-.0094 .0059-.0118
GRIP 5025Y .197 .098 .0020 .0020 .748 .134 • • • • • • • • .000-.098 .0091-.0165 .0043-.0083 .0047-.0094 .0059-.0138
GRIP 6030Y .236 .118 .0020 .0020 .748 .165 • • • • • • • • • .000-.118 .0094-.0197 .0051-.0098 .0047-.0110 .0059-.0157
GRIP 635-318Y .250 .125 .0020 .0020 .748 .157 • • • .000-.122 .0098-.0209 .0055-.0106 .0047-.0110 .0059-.0157
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50)
• HFPAD-6 (50) • HFPAD-JHP (48) • HGAER/L-3 (52) • HGAIR/L-3 (57) • HGHR/L-3 (39) • IM-HFIR-MC (62)

72 ISCAR
 FACE GROOVE-TURN
INSL (Ref.) 6˚
GRIPA ±0.025
Ground Double-Ended
Inserts for External, Internal
RE BW
and Face Machining
CW

M E T R I C
Dimensions Recommended Machining Data

f face-
ap f turn f groove groove f face-turn

IC07
Designation CW CWTOL(1) RE RETOL(2) INSL BW (mm) (mm/rev) (mm/rev) (mm/rev) (mm/rev)
GRIPA 3.00-0.40 3.00 0.020 0.40 0.030 16.00 2.28 • 0.25-1.80 0.15-0.19 0.07-0.11 0.08-0.14 0.12-0.20
GRIPA 4.00-0.40 4.00 0.020 0.40 0.030 19.02 2.82 • 0.50-2.40 0.18-0.24 0.09-0.15 0.10-0.20 0.14-0.31
GRIPA 5.00-0.40 5.00 0.020 0.40 0.030 19.02 3.40 • 0.50-3.00 0.20-0.30 0.11-0.20 0.11-0.23 0.16-0.34
GRIPA 6.00-0.80 6.00 0.020 0.80 0.050 19.00 4.20 • 0.50-3.60 0.24-0.42 0.13-0.25 0.11-0.26 0.19-0.41
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFHR/L-5T (43) • HFPAD-3 (49) • HFPAD-5 (50) • HFPAD-JHP (48) • HGAIR/L-3 (57)

INSL (Ref.) 6˚
GRIPA ±.00098
Ground Double-Ended
Inserts for External, Internal
RE BW
and Face Machining
CW

I N C H
Dimensions Recommended Machining Data

f face-
ap f turn f groove groove f face-turn
IC07

Designation CW CWTOL(1) RE RETOL(2) INSL BW (inch) (IPR) (IPR) (IPR) (IPR)

GRIPA 3.00-0.40 .118 .00079 .0158 .0012 .630 .090 • .010-.071 .0059-.0075 .0028-.0043 .0032-.0055 .0047-.0079
GRIPA 4.00-0.40 .157 .00079 .0158 .0012 .749 .111 • .020-.094 .0071-.0095 .0035-.0059 .0039-.0079 .0055-.0122
GRIPA 5.00-0.40 .197 .00079 .0158 .0012 .749 .134 • .020-.118 .0079-.0118 .0043-.0079 .0043-.0091 .0063-.0134
GRIPA 6.00-0.80 .236 .00079 .0315 .0020 .748 .165 • .020-.142 .0095-.0165 .0051-.0098 .0043-.0102 .0075-.0161
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFHR/L-5T (43) • HFPAD-3 (49) • HFPAD-5 (50) • HFPAD-JHP (48) • HGAIR/L-3 (57)

73
FACE GROOVE-TURN
INSL (Ref.) 6˚
GRIPA (full radius) ±0.025
Ground Double-Ended Full
Radius Inserts for External,
RE BW
Internal and Face Machining
CW

M E T R I C
Dimensions Recommended Machining Data

f face-
ap f turn f groove groove f face-turn

IC07
Designation CW CWTOL(1) RE RETOL(2) INSL BW (mm) (mm/rev) (mm/rev) (mm/rev) (mm/rev)
GRIPA 3.00-1.50 3.00 0.020 1.50 0.050 15.96 2.28 • 0.25-1.80 0.18-0.26 0.07-0.13 0.08-0.14 0.12-0.20
GRIPA 4.00-2.00 4.00 0.020 2.00 0.050 19.16 2.82 • 0.50-2.40 0.20-0.34 0.09-0.17 0.10-0.20 0.14-0.31
GRIPA 5.00-2.50 5.00 0.020 2.50 0.050 19.16 3.40 • 0.50-3.00 0.23-0.42 0.11-0.21 0.11-0.23 0.16-0.34
GRIPA 6.00-3.00 6.00 0.020 3.00 0.050 19.16 3.97 • 0.50-3.60 0.24-0.50 0.13-0.25 0.11-0.26 0.19-0.41
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFHR/L-5T (43) • HFPAD-3 (49) • HFPAD-5 (50) • HFPAD-JHP (48) • HGAIR/L-3 (57)

INSL (Ref.) 6˚
GRIPA (full radius) ±.00098
Ground Double-Ended Full
Radius Inserts for External,
RE BW
Internal and Face Machining
CW

I N C H
Dimensions Recommended Machining Data

f face-
ap f turn f groove groove f face-turn
IC07

Designation CW CWTOL(1) RE RETOL(2) INSL BW (inch) (IPR) (IPR) (IPR) (IPR)

GRIPA 3.00-1.50 .118 .00079 .0591 .0020 .628 .090 • .010-.071 .0071-.0102 .0028-.0051 .0032-.0055 .0047-.0079
GRIPA 4.00-2.00 .157 .00079 .0787 .0020 .754 .111 • .020-.094 .0079-.0134 .0035-.0067 .0039-.0079 .0055-.0122
GRIPA 5.00-2.50 .197 .00079 .0984 .0020 .754 .134 • .020-.118 .0091-.0165 .0043-.0083 .0043-.0091 .0063-.0134
GRIPA 6.00-3.00 .236 .00079 .1181 .0020 .754 .156 • .020-.142 .0095-.0197 .0051-.0098 .0043-.0102 .0075-.0161
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFHR/L-5T (43) • HFPAD-3 (49) • HFPAD-5 (50) • HFPAD-JHP (48) • HGAIR/L-3 (57)

74 ISCAR
 FACE GROOVE-TURN
±0.1 INSL CW
HGPL
Utility Double-Ended Inserts 7°
for Face Machining BW

RE
CW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data
f face- f face-
groove turn
ap

IC328

IC354

IC808

IC908

IC806
(mm/ (mm/

IC08
Designation CW BW RE CWTOL(1) RETOL(2) INSL (mm) rev) rev)
HGPL 3015Y 3.00 2.10 1.50 0.03 0.050 16.00 • • 0.00-1.50 0.08-0.20 0.12-0.23
HGPL 3002Y 3.00 2.30 0.20 0.03 0.050 16.00 • • • • 0.24-1.80 0.08-0.20 0.12-0.23
HGPL 3003Y 3.00 2.30 0.30 0.03 0.050 16.00 • • • • • 0.36-1.80 0.08-0.20 0.12-0.23
HGPL 4002Y 4.00 2.80 0.20 0.03 0.050 19.00 • • • • 0.24-2.40 0.10-0.24 0.16-0.30
HGPL 4004Y 4.00 2.80 0.40 0.03 0.050 19.00 • • • • 0.48-2.40 0.10-0.24 0.16-0.30
HGPL 4020Y 4.00 2.80 2.00 0.03 0.050 19.00 • • • 0.00-2.00 0.10-0.24 0.16-0.30
HGPL 5005Y 5.00 3.30 0.50 0.03 0.050 19.00 • • • 0.60-3.00 0.12-0.24 0.20-0.38
HGPL 5025Y 5.00 3.30 2.50 0.03 0.050 19.00 • • • 0.00-2.50 0.12-0.24 0.20-0.38
HGPL 6005Y 6.00 4.20 0.50 0.03 0.050 19.00 • • • • 0.60-3.60 0.12-0.28 0.24-0.45
HGPL 6030Y 6.00 4.20 3.00 0.03 0.050 19.00 • • • 0.00-3.00 0.12-0.28 0.24-0.45
• No depth penetration limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: C#-HFIR/L-MC (145) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)
• HFPAD-JHP (48) • HGAER/L-3 (52) • HGAIR/L-3 (57) • HGHR/L-3 (39)

±.004 INSL CW
HGPL
Utility Double-Ended Inserts 7°
for Face Machining BW

RE
CW

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f face-groove f face-turn
IC328

IC354

IC808

IC908

IC806
IC08

Designation CW BW RE CWTOL(1) RETOL(2) INSL (inch) (IPR) (IPR)

HGPL 3015Y .118 .083 .059 .0012 .0020 .630 • • .000-.059 .0031-.0079 .0047-.0091
HGPL 3002Y .118 .091 .008 .0012 .0020 .630 • • • • .009-.071 .0031-.0079 .0047-.0091
HGPL 3003Y .118 .091 .012 .0012 .0020 .630 • • • • • .014-.071 .0031-.0079 .0047-.0091
HGPL 4002Y .157 .110 .008 .0012 .0020 .748 • • • • .009-.094 .0039-.0094 .0063-.0118
HGPL 4004Y .157 .110 .016 .0012 .0020 .748 • • • • .019-.094 .0039-.0094 .0063-.0118
HGPL 4020Y .157 .110 .079 .0012 .0020 .748 • • • .000-.079 .0039-.0094 .0063-.0118
HGPL 5005Y .197 .130 .020 .0012 .0020 .748 • • • .024-.118 .0047-.0094 .0079-.0150
HGPL 5025Y .197 .130 .098 .0012 .0020 .748 • • • .000-.098 .0047-.0094 .0079-.0150
HGPL 6005Y .236 .165 .020 .0012 .0020 .748 • • • • .024-.142 .0047-.0110 .0094-.0177
HGPL 6030Y .236 .165 .118 .0012 .0020 .748 • • • .000-.118 .0047-.0110 .0094-.0177
• No depth penetration limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: C#-HFIR/L-MC (145) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)
• HFPAD-JHP (48) • HGAER/L-3 (52) • HGAIR/L-3 (57) • HGHR/L-3 (39)

75
FACE GROOVE-TURN

DO-GRIP
±0.1
HGN-C
Parting and Grooving Inserts
for Parting Bars, Hard Materials RE
and Tough Applications INSL
CW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC328

IC830

IC354

IC308

IC908
Designation CW RE CWTOL(1) INSL (mm/rev)
HGN 3003C 3.00 0.30 0.05 15.80 • • • • • 0.08-0.20
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)

For tools, see pages: • HFPAD-3 (49) • HFPAD-JHP (48) • HGAIR/L-3 (57) • HGHR/L-3 (39)

±.004
HGN-C
Parting and Grooving Inserts
for Parting Bars, Hard Materials RE
and Tough Applications INSL
CW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC328

IC830

IC354

IC308

IC908
Designation CW RE CWTOL(1) INSL (IPR)
HGN 3003C .118 .0118 .0020 .622 • • • • • .0031-.0079
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)

For tools, see pages: • HFPAD-3 (49) • HFPAD-JHP (48) • HGAIR/L-3 (57) • HGHR/L-3 (39)

76 ISCAR
 FACE GROOVE-TURN
HGN-J ±0.1
Inserts for Parting and
Grooving Soft Materials, RE
Parting Tubes, Small Diameters INSL
and Thin-Walled Parts CW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC328

IC830

IC354

IC308
Designation CW RE CWTOL(1) RETOL(2) INSL (mm/rev)
HGN 3002J 3.00 0.20 0.05 0.030 16.10 • • • • 0.04-0.15
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFPAD-3 (49) • HFPAD-JHP (48) • HGAIR/L-3 (57) • HGHR/L-3 (39)

HGN-J ±.004
Inserts for Parting and
Grooving Soft Materials, RE
Parting Tubes, Small Diameters INSL
and Thin-Walled Parts CW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC328

IC830

IC354

IC308
Designation CW RE CWTOL(1) RETOL(2) INSL (IPR)
HGN 3002J .118 .0079 .0020 .0012 .634 • • • • .0016-.0059
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFPAD-3 (49) • HFPAD-JHP (48) • HGAIR/L-3 (57) • HGHR/L-3 (39)

77
FACE GROOVE-TURN
±0.1
HGN-UT
Double-Sided Inserts for
Parting and Grooving Low RE

Feeds on Cr-Ni Alloys and CW

Low Carbon Steel INSL

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC328

IC354
Designation CW RE CWTOL(1) RETOL(2) INSL (mm/rev)
HGN 3003UT 3.00 0.30 0.05 0.030 15.80 • • 0.04-0.13
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFPAD-3 (49) • HFPAD-JHP (48) • HGAIR/L-3 (57) • HGHR/L-3 (39)

±.004
HGN-UT
Double-Sided Inserts for
Parting and Grooving Low RE

Feeds on Cr-Ni Alloys and CW

Low Carbon Steel INSL

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC328

IC354
Designation CW RE CWTOL(1) RETOL(2) INSL (IPR)
HGN 3003UT .118 .0118 .0020 .0012 .622 • • .0016-.0051
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • HFPAD-3 (49) • HFPAD-JHP (48) • HGAIR/L-3 (57) • HGHR/L-3 (39)

78 ISCAR
 FACE GROOVE-TURN
±0.1
DGN/DGNC/DGNM-C
Double-Sided Parting Inserts for
Parting and Grooving Bars, Hard RE
Materials and Tough Applications INSL
CW
DGN DGNM

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC1030
IC1028

IC5400
IC1010

IC30N
IC328
IC830
IC928

IC354

IC308
IC808
IC908

IC807
IC907
IC20
Designation CW CWTOL(3) RE RETOL(4) CDX(5) INSL (mm/rev)
DGN 4003C 4.00 0.04 0.30 0.030 - (6) 18.80 • • • • • • • • • • • • 0.10-0.30
DGNC 4003C (1) 4.00 0.04 0.30 0.030 - (6) 19.00 • • 0.10-0.30
DGN 4803C 4.80 0.04 0.30 0.030 - (6) 19.90 • 0.12-0.35
DGN 5003C 5.00 0.04 0.30 0.030 - (6) 19.10 • • • • • • • • • • 0.12-0.35
DGN 6303C 6.35 0.04 0.35 0.030 - (6) 19.10 • • • • • • • • 0.15-0.40
• Feed values for grade IC20 should be decreased by 50% • For cutting speed recommendations and user guide, see pages 161-173
(1) Inserts with coolant holes, recommended coolant pressure 10 bar minimum
(2) Single-ended insert
(3) Cutting width tolerance (+/-)
(4) Corner radius tolerance (+/-)
(5) Cutting depth maximum
(6) No depth limit

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60)
• HFAIR/L-DG (61) • HFFR/L-T (51) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)
• HFPAD-JHP (48) • IM-HFIR-MC (62)

±.004
DGN/DGNC/DGNM-C
Double-Sided Parting Inserts for
RE
Parting and Grooving Bars, Hard INSL
Materials and Tough Applications CW
DGN DGNC DGNM

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC1030
IC1028

IC5400
IC1010

IC30N
IC328
IC830
IC928

IC354

IC308
IC808
IC908

IC807
IC907
IC20

Designation CW CWTOL(3) RE RETOL(4) CDX(5) INSL (IPR)

DGN 4003C .157 .0016 .0118 .0012 - (6) .740 • • • • • • • • • • • • .0039-.0118
DGNC 4003C (1) .157 .0016 .0118 .0012 - (6) .748 • • .0039-.0118
DGN 4803C .189 .0016 .0118 .0012 - (6) .783 • .0047-.0138
DGN 5003C .197 .0016 .0118 .0012 - (6) .752 • • • • • • • • • • .0047-.0138
DGN 6303C .250 .0016 .0138 .0012 - (6) .752 • • • • • • • • .0059-.0158
• Feed values for grade IC20 should be decreased by 50% • For cutting speed recommendations and user guide, see pages 161-173
(1) Inserts with coolant holes, recommended coolant pressure 145PSI minimum
(2) Single-ended insert
(3) Cutting width tolerance (+/-)
(4) Corner radius tolerance (+/-)
(5) Cutting depth maximum
(6) No depth limit

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

79
FACE GROOVE-TURN
±0.1
DGN-MF
Double-Sided Inserts for Parting 7°

and Grooving Soft and Hard RE

Materials at Medium Feeds CW
INSL

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC1030

IC5400

IC1010
IC830

IC808
Designation CW RE CWTOL(1) CDX(2) INSL (mm/rev)
DGN 4003MF 4.00 0.30 0.04 - (3) 18.80 • • 0.08-0.20
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Cutting depth maximum
(3) No depth limit

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51) • HFHR/L-4T (41) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-JHP (48) • IM-HFIR-MC (62)

±.004
DGN-MF
Double-Sided Inserts for Parting 7°

and Grooving Soft and Hard RE

Materials at Medium Feeds CW
INSL

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

IC1030 f groove

IC5400

IC1010
IC830

IC808
Designation CW RE CWTOL(1) CDX(2) INSL (IPR)
DGN 4003MF .157 .0118 .0016 - .740 • • .0032-.0079
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Cutting depth maximum

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51) • HFHR/L-4T (41) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-JHP (48) • IM-HFIR-MC (62)

80 ISCAR
 FACE GROOVE-TURN
±0.1
DGN-W
Double-Sided Inserts with
Central Ridged Chipformer for RE
INSL
Parting and Grooving Hard CW
Materials and Interrupted Cuts

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC1030
IC328

IC354
Designation CW RE CWTOL(1) RETOL(2) INSL (mm/rev)
DGN 5003W 5.00 0.30 0.04 0.030 19.00 • • • 0.12-0.33
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-5T, 6T (53) • HFAIR/L-DG (61) • HFFR/L-T (51) • HFHR/L-5T (43) • HFIR/L-MC (63)
• HFPAD-5 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

±.004
DGN-W
Double-Sided Inserts with
Central Ridged Chipformer for RE
INSL
Parting and Grooving Hard
CW
Materials and Interrupted Cuts

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC1030
IC328

Designation CW RE CWTOL(1) RETOL(2) INSL IC354 (IPR)

DGN 5003W .197 .0118 .0016 .0012 .748 • • • .0047-.0130
• No depth limit • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-5T, 6T (53) • HFAIR/L-DG (61) • HFFR/L-T (51) • HFHR/L-5T (43) • HFIR/L-MC (63)
• HFPAD-5 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

81
FACE GROOVE-TURN
±0.1 DGN 1002 DGNM
DGN/DGNM-J/JS/JT
Double-Sided Inserts for Parting 7°
and Grooving Soft Materials,
RE
Parting Tubes, Small Diameters INSL CDX
and Thin-Walled Parts CW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC1030
IC1028

IC5400
IC1010
IC328
IC830
IC928

IC354

IC308
IC808
IC908

IC807
IC20
Designation CW CWTOL(3) RE RETOL(4) CDX(5) INSL (mm/rev)
DGN 4003J 4.00 0.04 0.30 0.030 - (6) 18.90 • • • • • • • • • • • 0.05-0.18
DGN 4003JT 4.00 0.04 0.30 0.030 - (6) 18.90 • 0.05-0.18
DGN 4803J 4.80 0.04 0.30 0.030 - (6) 20.40 • 0.05-0.20
DGN 5003J 5.00 0.04 0.30 0.030 - (6) 19.00 • • • • • • • • • 0.05-0.20
DGN 5003JT 5.00 0.04 0.30 0.030 - (6) 19.00 • • 0.05-0.20
DGN 6303J 6.35 0.04 0.35 0.030 - (6) 19.10 • • • • • • • • • 0.05-0.25
DGN 6303JT 6.35 0.04 0.35 0.030 - (6) 19.10 • • 0.05-0.25
• JT chipformer has the basic positive configuration of the J-type and a reinforced negative frontal edge; most suitable for soft materials at low to medium feeds
• For cutting speed recommendations and user guide, see pages 161-173
(1) Sharp corners
(2) Single-ended insert
(3) Cutting width tolerance (+/-)
(4) Corner radius tolerance (+/-)
(5) Cutting depth maximum
(6) No depth limit

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

±.004 DGN 1002 DGNM

DGN/DGNM-J/JS/JT
Double-Sided Inserts for Parting 7°
and Grooving Soft Materials,
RE
Parting Tubes, Small Diameters INSL CDX
and Thin-Walled Parts CW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC1030
IC1028

IC5400
IC1010
IC328
IC830
IC928

IC354

IC308
IC808
IC908

IC807
IC20

Designation CW CWTOL(3) RE RETOL(4) CDX(5) INSL (IPR)

DGN 4003J .157 .0016 .0118 .0012 - (6) .744 • • • • • • • • • • • .0020-.0071
DGN 4003JT .157 .0016 .0118 .0012 - (6) .744 • .0020-.0071
DGN 4803J .189 .0016 .0118 .0012 - (6) .803 • .0020-.0079
DGN 5003J .197 .0016 .0118 .0012 - (6) .748 • • • • • • • • • .0020-.0079
DGN 5003JT .197 .0016 .0118 .0012 - (6) .748 • • .0020-.0079
DGN 6303J .250 .0016 .0138 .0012 - (6) .752 • • • • • • • • • .0020-.0098
DGN 6303JT .250 .0016 .0138 .0012 - (6) .752 • • .0020-.0098
• JT chipformer has the basic positive configuration of the J-type and a reinforced negative frontal edge; most suitable for soft materials at low to medium feeds
• For cutting speed recommendations and user guide, see pages 161-173
(1) Sharp corners
(2) Single-ended insert
(3) Cutting width tolerance (+/-)
(4) Corner radius tolerance (+/-)
(5) Cutting depth maximum
(6) No depth limit

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)
• HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFIR/L-MC (63) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

82 ISCAR
 FACE GROOVE-TURN
CUT-GRIP (long pocket)
LH
GHFG-R/L-8
DAXN-DAXX HF H
Holders for Face Grooving
and Turning Along Shafts OAL GHFG-25-50R-8
CW
CDX

WF B

Right-hand shown

M E T R I C

Designation CW CDX DAXN(1) DAXX(2) H HF B OAL LH WF

GHFG 25-50R/L-8 8.00 25.00 50.0 64.0 25.0 25.0 25.0 150.00 41.0 22.00 SR M6X20 DIN912 HW 5.0
GHFG 25-63R/L-8 8.00 25.00 63.0 82.0 25.0 25.0 25.0 150.00 41.0 22.00 SR M6X20 DIN912 HW 5.0
GHFG 32-63R-8 8.00 25.00 63.0 82.0 32.0 32.0 32.0 170.00 41.0 30.00 SR M6X20 DIN912 HW 5.0

I N C H

Designation CW CDX DAXN(1) DAXX(2) H HF B OAL LH WF

GHFG 25.4-50R/L-8 .315 1.000 1.97 2.52 1.000 1.000 1.000 6.000 1.600 .870 SR M6X20 DIN912 HW 5.0
GHFG 25.4-63R/L-8 .315 1.000 2.48 3.23 1.000 1.000 1.000 6.000 1.600 .870 SR M6X20 DIN912 HW 5.0
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GDMF (100) • GDMM-CC (108) • GDMN (98) • GDMU (99) • GDMY (95) • GDMY (full radius) (96) • GDMY-F (97)
• GIA-K (long pocket) (93) • GIF (long pocket) (91) • GIF-E (W=8,10 full radius) (92) • GIF-E (W=8,10) (90) • GIFG-E (W=8) (89)

83
FACE GROOVE-TURN
LH
CDX
GHFGR/L-8 HF H
Holders for Face Grooving
HBH
and Turning DAXN-DAXX OAL

WF B
CW
Right-hand shown

M E T R I C

Designation CDX DAXN(1) DAXX(2) H HF B CW OAL LH WF HBH

GHFGR/L 25-80-8 23.00 80.0 115.0 25.0 25.0 25.0 8.00 150.00 43.5 21.30 6.0 SR M6X20 DIN912 HW 5.0
GHFGR/L 32-80-8 23.00 80.0 115.0 32.0 32.0 32.0 8.00 170.00 43.5 28.30 - SR M6X20 DIN912 HW 5.0
GHFGR/L 25-105-8 25.00 105.0 160.0 25.0 25.0 25.0 8.00 150.00 43.5 21.30 6.0 SR M6X20 DIN912 HW 5.0
GHFGR/L 32-105-8 25.00 105.0 160.0 32.0 32.0 32.0 8.00 170.00 43.5 28.30 - SR M6X20 DIN912 HW 5.0
GHFGR/L 25-155-8 25.00 155.0 510.0 25.0 25.0 25.0 8.00 150.00 43.5 21.30 6.0 SR M6X20 DIN912 HW 5.0
GHFGR/L 32-155-8 25.00 155.0 510.0 32.0 32.0 32.0 8.00 170.00 43.5 28.30 - SR M6X20 DIN912 HW 5.0
• No limitation to widening the groove either way after initial grooving • CDX depends on the penetration diameter and the insert
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GDMF (100) • GDMM-CC (108) • GDMN (98) • GDMU (99) • GDMY (95) • GDMY (full radius) (96) • GDMY-F (97)
• GIA-K (long pocket) (93) • GIF (long pocket) (91) • GIF-E (W=8,10 full radius) (92) • GIF-E (W=8,10) (90) • GIFG-E (W=8) (89)
• GIPA/GIDA 8 (full radius) (105)

CDX for GHFGR/L (25/32)-80-8

D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
80 16 23 23 20 24 16 24
82 17 23 23 20 24 17 24
84 18 23 23 21 24 18 24
86 19 23 23 21 24 19 24
88 20 23 23 22 24 20 24
90 20 23 23 22 24 20 24
96 20 23 23 22 24 20 24
104 20 23 23 22 24 20 24
115 22 23 23 22 24 22 24
CDX for GHFGR/L (25/32)-105-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
105 21 23 23 23 24 21 24
114 22 23 23 23 24 22 24
126 23 23 24 23 24 23 24
140-160 24 24 24 23 24 24 24
CDX for GHFGR/L (25/32)-155-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
155 24 24 24 23 24 24 24
180 24 24 24 23 24 24 24
210-510 24 24 24 23 24 24 24

84 ISCAR
 FACE GROOVE-TURN
LH
CDX
GHFGR/L-8 H H
Holders for Face Turning
HBH
and Grooving DAXN-DAXX OAL

WF B
CW
Right-hand shown

I N C H

Designation CDX DAXN(1) DAXX(2) H B CW OAL LH WF HBH

GHFGR/L 25.4-80-8 .905 3.15 4.53 1.000 1.000 .315 6.000 1.710 .840 .30 SR M6X20 DIN912 HW 5.0
GHFGR 31.7-80-8 .905 3.15 4.53 1.250 1.250 .315 7.000 1.710 1.110 - SR M6X25 DIN912 HW 5.0
GHFGR 25.4-105-8 .984 4.13 6.30 1.000 1.000 .315 6.000 1.710 .840 .24 SR M6X20 DIN912 HW 5.0
GHFGR 31.7-105-8 .984 4.13 6.30 1.250 1.250 .315 6.700 1.710 1.110 - SR M6X20 DIN912 HW 5.0
GHFGR/L 25.4-155-8 .984 6.10 20.10 1.000 1.000 .315 6.000 1.710 .840 .24 SR M6X20 DIN912 HW 5.0
GHFGR/L 31.7-155-8 .984 6.10 20.10 1.250 1.250 .315 6.700 1.710 1.110 - SR M6X20 DIN912 HW 5.0
• No limitation to widening the groove either way after initial grooving • CDX depends on the penetration diameter and the insert
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GDMF (100) • GDMM-CC (108) • GDMN (98) • GDMU (99) • GDMY (95) • GDMY (full radius) (96) • GDMY-F (97)
• GIA-K (long pocket) (93) • GIF (long pocket) (91) • GIF-E (W=.315,.394 full radius) (92) • GIF-E (W=.315,.394) (90) • GIFG-E (W=.315) (89)
• GIPA/GIDA 8 (full radius) (105)

CDX for GHFGR/L (25.4/31.7)-80-8

D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
3.150 .630 .906 .906 .787 .945 .630 .945
3.228 .669 .906 .906 .787 .945 .669 .945
3.307 .709 .906 .906 .827 .945 .709 .945
3.386 .748 .906 .906 .827 .945 .748 .945
3.465 .787 .906 .906 .866 .945 .787 .945
3.543 .787 .906 .906 .866 .945 .787 .945
3.780 .787 .906 .906 .866 .945 .787 .945
4.094 .787 .906 .906 .866 .945 .787 .945
4.528 .866 .906 .906 .866 .945 .866 .945
CDX for GHFGR/L (25.4/31.7)-105-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
4.134 .827 .906 .906 .906 .945 .827 .945
4.488 .866 .906 .906 .906 .945 .866 .945
4.961 .906 .906 .945 .906 .945 .906 .945
5.512-6.299 .945 .945 .945 .906 .945 .945 .945
CDX for GHFGR/L (25.4/31.7)-155-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
6.102 .945 .945 .945 .906 .945 .945 .945
7.087 .945 .945 .945 .906 .945 .945 .945
8.268-20.079 .945 .945 .945 .906 .945 .945 .945

85
FACE GROOVE-TURN
GADR-8

GHAR/L-8 HF H
External Holders for Grooving HBH
OHX
and Turning Adapters OAL
LH
WF(assembly) WF (holder) B

GAFG-L-8 CDX GHAR

Right-hand shown

M E T R I C

Designation H HF B WF(1) OAL LH OHX(2) HBH TGA(3) CDX(4) FG(5)

GHAR/L 25-8 25.0 25.0 25.0 16.0 124.50 45.0 25.50 14.0 GADR/L 8 25.50 GAFG...R/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0
GHAR/L 32-8 32.0 32.0 32.0 23.0 144.50 45.0 25.50 7.0 GADR/L 8 25.50 GAFG...R/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0
• Adapters GADR/L-8 for turning and grooving, GAFG-R/L-8 for face-grooving (to be ordered separately)
(1) WF(holder)
(2) Maximum overhang
(3) Adapter for Turning & Grooving
(4) See specific adapter dimensions
(5) Adapter for Face Grooving

For tools, see pages: • GAFG-R/L-8 (87)

GADR-8

GHAR/L-8 HF H
External Holders for Grooving HBH
OHX
and Turning Adapters OAL
LH
WF(assembly) WF B

GAFG-L-8 CDX GHAR

Right-hand shown

I N C H
Designation H HF WF B OAL LH OHX(1) HBH TGA CDX(2) FG
GHAR/L 25.4-8 1.000 1.000 .646 1.000 5.000 1.770 1.000 .54 GADR/L 8 1.000 GAFG...R/L-8
GHAR/L 31.7-8 1.250 1.250 .896 1.250 6.000 1.770 1.000 .29 GADR/L 8 1.000 GAFG...R/L-8
• Adapters GADR/L-8 for turning and grooving, GAFG-R/L-8 for face-grooving
(1) Maximum overhang
(2) See specific adapter dimensions

For tools, see pages: • GAFG-R/L-8 (87)

Spare Parts

Designation
GHAR/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0

86 ISCAR
 FACE GROOVE-TURN
OAL

GHAPR/L-8 HF H
External Holders for Grooving HBH
LH
and Turning Perpendicularly
B
Oriented Adapters
CDX

GAFG…R-8 GADL 8 GHAPR Right-hand shown

M E T R I C

Designation H HF B OAL LH HBH TGA(1) CDX(2) FG(3)

GHAPR/L 32-8 32.0 32.0 32.0 155.00 30.0 7.0 GADR/L 8 25.50 GAFG...R/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0

I N C H

Designation H HF B OAL LH HBH TGA(1) CDX(2) FG(3)

GHAPR/L 31.7-8 1.250 1.250 1.250 6.100 1.180 .29 GADR/L 8 1.000 GAFG...R/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0
• Adapters GADR/L-8 for turning and grooving, GAFG-R/L-8 for face-grooving (to be ordered separately)
(1) Adapter for Turning & Grooving
(2) See specific adapter dimensions
(3) Adapter for Face Grooving

For tools, see pages: • GAFG-R/L-8 (87)

OAL
GAFG-R/L-8 CDX
Adapters for Face Machining OAH HF

DAXN-DAXX
WF CDX GAFG-...L8
For face grooving

CW Left-hand shown

M E T R I C
Designation CW DAXN(1) DAXX(2) CDX(3) WF HF OAH OAL
GAFG 80R/L-8 8.00 80.0 115.0 23.00 9.00 32.0 42.0 63.50
GAFG 105R/L-8 8.00 105.0 160.0 25.00 9.00 32.0 42.0 63.50
GAFG 155R/L-8 8.00 155.0 510.0 25.00 9.00 32.0 42.0 63.50

I N C H
Designation CW DAXN(1) DAXX(2) CDX(3) WF HF OAH OAL
GAFG 80R/L-8 .315 3.15 4.53 .906 .354 1.260 1.654 2.500
GAFG 105R/L-8 .315 4.13 6.30 .984 .354 1.260 1.654 2.500
GAFG 155R/L-8 .315 6.10 20.08 .984 .354 1.260 1.654 2.500
• No limitation for widening the groove either way after initial grooving • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
(3) For GIFG-8 & GDMY-8 CDX=25 mm for DAX range

For inserts, see pages: GDMA (94) • GDMF (100) • GDMM-CC (108) • GDMN (98) • GDMU (99) • GDMY (95) • GDMY (full radius) (96) • GDMY-F (97)
• GIA-K (long pocket) (93) • GIF (long pocket) (91) • GIF-E (W=8,10 full radius) (92) • GIF-E (W=8,10) (90) • GIFG-E (W=8) (89) • GIPA/GIDA 8 (full radius) (105)
For holders, see pages: C#-GHAD-8 (142) • C#-GHAPR/L-8 (143) • GHAPR/L-8 (87) • GHAR/L-8 (86) • IM-GHAD-8 (151)

87
FACE GROOVE-TURN

CGFG 51-P8 CDX OAL

Blades for Face Machining
Carrying 8 mm Inserts H OAH
DAXN-DAXX HF

WB_2
Left-hand shown

M E T R I C

Designation CW DAXN(1) DAXX(2) CDX H HF OAL OAH WB_2

CGFG 51-180R/L-P8 8.00 180.0 240.0 70.00 52.6 45.0 200.00 60.0 27.5 SR M4-2052 HW 3.0
CGFG 51-240R/L-P8 8.00 240.0 320.0 80.00 52.6 45.0 210.00 70.0 26.0 SR M4-2052 HW 3.0
CGFG 51-320R/L-P8 8.00 320.0 440.0 90.00 52.6 45.0 220.00 80.0 24.5 SR M4-2052 HW 3.0
CGFG 51-440R/L-P8 8.00 440.0 700.0 100.00 52.6 45.0 230.00 90.0 22.5 SR M4-2052 HW 3.0
CGFG 51-700R/L-P8 8.00 700.0 1500.0 120.00 52.6 45.0 250.00 100.0 20.0 SR M4-2052 HW 3.0
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GIMF (101) • GIMM 8CC (107) • GIMY (102) • GIMY (full radius) (104) • GIMY-F (103) • GIPY (106)
For holders, see pages: SGTBK (135) • SGTBU/SGTBN (133)

CGFG 51-P8 CDX OAL

Blades for Face Machining
Carrying .315" Inserts H OAH
DAXN-DAXX HF

WB_2
Left-hand shown

I N C H

Designation CW DAXN(1) DAXX(2) CDX H HF OAL OAH WB_2

CGFG 51-180R/L-P8 .315 7.09 9.45 2.756 2.071 1.772 7.874 2.36 1.083 SR M4-2052 HW 3.0
CGFG 51-240R/L-P8 .315 9.45 12.60 3.150 2.071 1.772 8.268 2.76 1.024 SR M4-2052 HW 3.0
CGFG 51-320R/L-P8 .315 12.60 17.32 3.543 2.071 1.772 8.661 3.15 .965 SR M4-2052 HW 3.0
CGFG 51-440R/L-P8 .315 17.32 27.56 3.937 2.071 1.772 9.055 3.54 .886 SR M4-2052 HW 3.0
CGFG 51-700R/L-P8 .315 27.56 59.06 4.724 2.071 1.772 9.843 3.94 .787 SR M4-2052 HW 3.0
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GIMF (101) • GIMM 8CC (107) • GIMY (102) • GIMY (full radius) (104) • GIMY-F (103) • GIPY (106)
For holders, see pages: SGTBK (135) • SGTBU/SGTBN (133)

88 ISCAR
 FACE GROOVE-TURN
±0.1
30 Ref.
GIFG-E (W=8)
CDX
Inserts for Deep Face 6.4
Grooving and Turning RE
DAXN BW

CW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f face-groove

IC635

IC20
Designation CW RE CWTOL(1) RETOL(2) DAXN(3) CDX(4) BW (mm/rev)
GIFG 8.00E-0.80 8.00 0.80 0.02 0.050 50.0 25.00 6.00 • • 0.15-0.25
GIFG 8.00E-1.20 8.00 1.20 0.02 0.050 50.0 25.00 6.00 • 0.15-0.25
• For cutting speed recommendations, see pages 162-164
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Cutting depth maximum

For tools, see pages: GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004 1.18 R
GIFG-E (W=.315) ef.
CDX
Inserts for Deep Face .252
Grooving and Turning RE
DAXN BW
CW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f face-groove
IC635

Designation CW RE CWTOL(1) RETOL(2) DAXN(3) CDX(4) BW IC20 (IPR)

GIFG 8.00E-0.80 .315 .031 .0008 .0020 1.97 .984 .236 • • .0059-.0098
GIFG 8.00E-1.20 .315 .047 .0008 .0020 1.97 .984 .236 • .0059-.0098
• For cutting speed recommendations, see pages 162-164
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Cutting depth maximum

For tools, see pages: GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

89
FACE GROOVE-TURN
±0.025
GIF-E (W=8,10) 30 Ref.
Precision Double-Ended Inserts 7° 6.4
for Grooving and Turning BW
CW
RE

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data
f
f turn groove

IC8250

IC5010
ap

IC830

IC808

IC908

IC428

IC806

IC807
(mm/ (mm/

IC20
Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) (mm) rev) rev)
GIF 8.00E-0.40 8.00 0.40 0.02 0.030 6.00 27.00 • • • 0.50-4.80 0.29-0.48 0.18-0.31
GIF 8.00E-0.80 8.00 0.80 0.02 0.050 6.00 27.00 • • • • • • • • • 1.00-4.80 0.32-0.56 0.18-0.34
GIF 8.00E-1.20 8.00 1.20 0.02 0.050 6.00 27.00 • • • • • • • 1.45-4.80 0.32-0.62 0.18-0.34
GIF 10.00E-0.80 10.00 0.80 0.02 0.050 8.00 27.00 • • • • • • • • 1.00-6.00 0.35-0.65 0.22-0.40
GIF 10.00E-1.20 10.00 1.20 0.02 0.050 8.00 27.00 • • • • • • 1.45-6.00 0.35-0.72 0.22-0.40
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.001 1.18 Ref.

GIF-E (W=.315,.394)
Precision Double-Ended Inserts 7° .252
for Grooving and Turning BW
CW
RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data
IC8250

IC5010

ap f turn f groove
IC830

IC808
IC908

IC428
IC806
IC807
IC20

Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) (inch) (IPR) (IPR)

GIF 8.00E-0.40 .315 .0160 .0008 .0012 .236 1.063 • • • .020-.189 .0114-.0189 .0071-.0122
GIF 8.00E-0.80 .315 .0315 .0008 .0020 .236 1.063 • • • • • • • • • .039-.189 .0126-.0220 .0071-.0134
GIF 8.00E-1.20 .315 .0472 .0008 .0020 .236 1.063 • • • • • • • .057-.189 .0126-.0244 .0071-.0134
GIF 10.00E-0.80 .394 .0315 .0008 .0020 .315 1.063 • • • • • • • • .039-.236 .0138-.0256 .0087-.0157
GIF 10.00E-1.20 .394 .0472 .0008 .0020 .315 1.063 • • • • • • .057-.236 .0138-.0283 .0087-.0157
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

90 ISCAR
 FACE GROOVE-TURN
±0.025 30 Ref.
GIF (long pocket)
Precision Double-Ended
7˚ 6.4
Inserts for Grooving
CW
RE BW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove f face-groove

IC806
IC20
Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) (mm/rev) (mm/rev)
GIF 8.00-0.40 8.00 0.40 0.02 0.030 6.00 27.00 • • 0.18-0.31 0.14-0.23
GIF 8.00-0.80 8.00 0.80 0.02 0.050 6.00 27.00 • • 0.18-0.34 0.14-0.25
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

1.18 Ref
±.001 .
GIF (long pocket)
Precision Double-Ended
7˚ .252
Inserts for Grooving

CW
RE BW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove f face-groove
IC806
IC20

Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) (IPR) (IPR)

GIF 8.00-0.40 .315 .0157 .0008 .0012 .236 1.063 • • .0071-.0122 .0055-.0091
GIF 8.00-0.80 .315 .0315 .0008 .0020 .236 1.063 • • .0071-.0134 .0055-.0098
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

91
FACE GROOVE-TURN
±0.025 30 Ref.
GIF-E (W=8,10 full radius)
Precision Double-Ended
7° 6.4
Full Radius Inserts for
BW
Profiling and Grooving
CW
RE

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC8250
IC830
Designation CW RE CWTOL(1) RETOL(2) BW (mm) (mm/rev) (mm/rev)
GIF 8.00E-4.00 8.00 4.00 0.02 0.050 6.00 • 0.00-4.00 0.32-0.67 0.18-0.34
GIF 10.00E-5.00 10.00 5.00 0.02 0.050 8.00 • • 0.00-5.00 0.35-0.78 0.22-0.40
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.001 1.18 Ref.

GIF-E
(W=.315,.394 full radius) 7° .252
Precision Double-Ended
BW
Full Radius Inserts for
Profiling and Grooving CW
RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC8250
IC830

Designation CW RE CWTOL(1) RETOL(2) BW (inch) (IPR) (IPR)

GIF 8.00E-4.00 .315 .157 .0008 .0020 .236 • .000-.157 .0126-.0264 .0071-.0134
GIF 10.00E-5.00 .394 .197 .0008 .0020 .315 • • .000-.197 .0138-.0307 .0087-.0157
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

92 ISCAR
 FACE GROOVE-TURN
±0.025
30 Ref.
GIA-K (long pocket) 15°
Flat Top Precision CDX
7° 6.4
Double-Ended Inserts with
BW
T-Land for Machining Cast Iron DAXN
CW
RE

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC5010

IC428
Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) DAXN(4) (mm) (mm/rev) (mm/rev)
GIA 8.00K-0.80 8.00 0.80 0.02 0.050 6.00 25.00 160.0 • • 1.00-4.80 0.36-0.64 0.18-0.38
GIA 8.00K-1.20 8.00 1.20 0.02 0.050 6.00 25.00 160.0 • • 1.45-4.80 0.36-0.70 0.18-0.38
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum
(4) Minimum axial grooving diameter

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.001
1.18 Ref.
GIA-K (long pocket) 15°
Flat Top Precision CDX 7° .252
Double-Ended Inserts with
BW
T-Land for Machining Cast Iron DAXN
CW
RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC5010

IC428

Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) DAXN(4) (inch) (IPR) (IPR)

GIA 8.00K-0.80 .315 .031 .0008 .0020 .236 .984 6.30 • • .039-.189 .0142-.0252 .0071-.0150
GIA 8.00K-1.20 .315 .047 .0008 .0020 .236 .984 6.30 • • .057-.189 .0142-.0276 .0071-.0150
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum
(4) Minimum axial grooving diameter

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

93
FACE GROOVE-TURN
±0.1 30 Ref.
GDMA
Utility Double-Ended Insert 7° 6.4
for Machining Aluminum
CW

RE BW
Can cut arcs to 250°

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC507
IC07
Designation CW RE CWTOL(1) RETOL(2) BW (mm) (mm/rev) (mm/rev)
GDMA 840 8.00 4.00 0.05 0.050 5.60 • • 0.00-4.00 0.24-0.67 0.14-0.38
• For heavy-duty machining • DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87)

±.004 1.18 Ref.

GDMA
Utility Double-Ended Insert 7° .252
for Machining Aluminum
CW

RE BW
Can cut arcs to 250°

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC507
IC07

Designation CW RE CWTOL(1) RETOL(2) BW (inch) (IPR) (IPR)

GDMA 840 .315 .157 .0020 .0020 .220 • • .000-.157 .0094-.0264 .0055-.0150
• For heavy-duty machining • DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87)

94 ISCAR
 FACE GROOVE-TURN
±0.1 30 Ref.
GDMY
Utility Double-Ended Inserts CDX 7° 6.4
for Grooving and Turning
DAXN
CW
RE BW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f turn f groove
ap

IC8250

IC5010
(mm/ (mm/

IC830

IC808

IC908

IC428
IC20
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) CDX(4) (mm) rev) rev)
GDMY 808 8.00 0.80 0.05 0.050 6.00 50.0 27.00 • • • • • • • 1.00-4.80 0.32-0.56 0.18-0.34
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004 1.18 Ref.

GDMY
CDX 7°
Utility Double-Ended Inserts .252
for Grooving and Turning
DAXN
CW
RE BW

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC8250

IC5010
IC830

IC808

IC908

IC428
IC20

Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) CDX(4) (inch) (IPR) (IPR)

GDMY 808 .315 .031 .0020 .0020 .236 1.97 1.063 • • • • • • • .039-.189 .0126-.0220 .0071-.0134
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

95
FACE GROOVE-TURN
±0.1 30 Ref.
GDMY (full radius)
Utility Double-Ended Full Radius 7°
CDX 6.4
Inserts for Grooving and Profiling
DAXN CW

RE BW

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC8250

IC5010
IC830

IC808
IC908

IC428
IC806
IC20
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) CDX (mm) (mm/rev) (mm/rev)
GDMY 840 8.00 4.00 0.05 0.050 5.60 50.0 25.00 • • • • • • • • 0.00-4.00 0.32-0.67 0.18-0.34
• Can cut arcs to 250° • DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004 1.18 Ref.

GDMY (full radius)
Utility Double-Ended Full Radius CDX 7°
.252
Inserts for Grooving and Profiling
DAXN CW

RE BW

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC8250

IC5010
IC830

IC808
IC908

IC428
IC806
IC20

Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) CDX (inch) (IPR) (IPR)

GDMY 840 .315 .157 .0020 .0020 .220 1.97 .984 • • • • • • • • .000-.157 .0126-.0264 .0071-.0134
• Can cut arcs to 250° • DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

96 ISCAR
 FACE GROOVE-TURN
±0.1 30 Ref.
GDMY-F
Utility Double-Ended Inserts 7º 6.3 Ref.
for Grooving and Profiling
Ductile Materials CW
RE BW

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC808

IC908
Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) (mm) (mm/rev) (mm/rev)
GDMY 840F 8.00 4.00 0.05 0.050 5.60 25.00 • • 0.00-4.00 0.32-0.67 0.18-0.34
• DMIN for internal applications = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004 1.18 Ref.

GDMY-F
Utility Double-Ended Inserts 7º .248 Ref.
for Grooving and Profiling
Ductile Materials CW
RE BW

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC808

IC908

Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) (inch) (IPR) (IPR)

GDMY 840F .315 .157 .0020 .0020 .220 .984 • • .000-.157 .0126-.0264 .0071-.0134
• DMIN for internal applications = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

97
FACE GROOVE-TURN
±0.1
GDMN 30 Ref.
Utility Double-Ended Inserts 7° 6.4
for Grooving and Turning BW
Ductile Materials
CW
RE

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

IC8250
ap f turn f groove

IC830

IC808

IC907
Designation CW RE CWTOL(1) RETOL(2) CDX(3) BW (mm) (mm/rev) (mm/rev)
GDMN 808 8.00 0.80 0.05 0.050 27.00 6.00 • • • • 1.00-3.20 0.20-0.35 0.10-0.30
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004 1.18 Ref.

GDMN
Utility Double-Ended Inserts 7° .252
for Grooving and Turning BW
Ductile Materials
CW
RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data
IC8250

ap f turn f groove
IC830

IC808

IC907

Designation CW RE CWTOL(1) RETOL(2) CDX(3) BW (inch) (IPR) (IPR)

GDMN 808 .315 .031 .0020 .0020 1.063 .236 • • • • .039-.126 .0079-.0138 .0039-.0118
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

98 ISCAR
 FACE GROOVE-TURN
±0.1 30 Ref.
GDMU
Utility Inserts for Heavy RE 7° 6.4
Grooving on Ductile Materials
CW
BW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove

IC8250
IC830
Designation CW RE CWTOL(1) RETOL(2) BW (mm/rev)
GDMU 808 8.00 0.80 0.05 0.050 6.00 • • 0.10-0.24
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004 1.18 Ref

GDMU .
Utility Inserts for Heavy 7° .252
Grooving on Ductile Materials RE

CW
BW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f groove
IC8250
IC830

Designation CW RE CWTOL(1) RETOL(2) BW (IPR)

GDMU 808 .315 .031 .0020 .0020 .236 • • .0039-.0094
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

99
FACE GROOVE-TURN
±0.1 30 Ref.
GDMF
7°
Utility Double-Ended Inserts 6.4
for Grooving and Turning
CW
RE BW

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

IC8250

IC5010
ap f turn f groove

IC830

IC808

IC428
Designation CW RE CWTOL(1) RETOL(2) CDX(3) BW (mm) (mm/rev) (mm/rev)
GDMF 808 8.00 0.80 0.05 0.050 27.00 6.00 • • • • • 1.00-4.80 0.32-0.56 0.18-0.34
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

±.004
GDMF
Utility Double-Ended Inserts 7°
.602 Ref. .197
for Grooving and Turning
CW
RE BW

I N C H
Dimensions Tough 1 Hard Recommended Machining Data
IC8250

IC5010

ap f turn f groove
IC830

IC808

IC428

Designation CW RE CWTOL(1) RETOL(2) CDX(3) BW (inch) (IPR) (IPR)

GDMF 808 .315 .031 .0020 .0020 1.063 .236 • • • • • .039-.189 .0126-.0220 .0071-.0134
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

100 ISCAR
 FACE GROOVE-TURN
±0.1
GIMF 7º
Utility Single-Ended Inserts 15.3 Ref.
for Grooving and Turning 5
CW BW

RE

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC8250

IC5010
IC830

IC808
IC908

IC428
IC806
IC907

IC804
IC20

IC4
Designation CW RE CWTOL(1) RETOL(2) BW (mm) (mm/rev) (mm/rev)
GIMF 406 4.00 0.60 0.05 0.050 3.40 • • • • • • • • • • • 0.75-2.40 0.19-0.25 0.09-0.16
GIMF 502 5.00 0.20 0.05 0.050 4.00 • • 0.25-3.00 0.18-0.26 0.11-0.18
GIMF 508 5.00 0.80 0.05 0.050 4.00 • • • • • • • • • • 1.00-3.00 0.23-0.35 0.11-0.21
GIMF 605 6.00 0.50 0.05 0.050 5.00 • • 0.60-3.60 0.22-0.36 0.13-0.23
GIMF 608 6.00 0.80 0.05 0.050 5.00 • • • • • • • • • 1.00-3.60 0.24-0.42 0.13-0.25
GIMF 808 8.00 0.80 0.05 0.050 6.00 • • • 1.00-4.80 0.32-0.56 0.18-0.34
• DMIN for internal applications = 70 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

±.004
GIMF 7º
Utility Single-Ended Inserts
.602 Ref.
for Grooving and Turning .197

CW BW

RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC8250

IC5010
IC830

IC808
IC908

IC428
IC806
IC907

IC804
IC20

IC4

Designation CW RE CWTOL(1) RETOL(2) BW (inch) (IPR) (IPR)

GIMF 406 .157 .024 .0020 .0020 .134 • • • • • • • • • • • .030-.094 .0075-.0098 .0035-.0063
GIMF 502 .197 .008 .0020 .0020 .157 • • .010-.118 .0071-.0102 .0043-.0071
GIMF 508 .197 .031 .0020 .0020 .157 • • • • • • • • • • .039-.118 .0091-.0138 .0043-.0083
GIMF 605 .236 .020 .0020 .0020 .197 • • .024-.142 .0087-.0142 .0051-.0091
GIMF 608 .236 .031 .0020 .0020 .197 • • • • • • • • • .039-.142 .0094-.0165 .0051-.0098
GIMF 808 .315 .031 .0020 .0020 .236 • • • .039-.189 .0126-.0220 .0071-.0134
• DMIN for internal applications = 2.76" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

101
FACE GROOVE-TURN
±0.1
GIMY
Utility Single-Ended Inserts 7˚ 5
BW 15.3 Ref.
for Grooving and Turning CW
CW
RE BW
RE
GIMY 8, 10 GIMY 3

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC8250
IC830

IC808

IC908

IC806

IC804
IC20

IC4
Designation CW RE CWTOL(1) RETOL(2) BW (mm) (mm/rev) (mm/rev)
GIMY 304 3.00 0.40 0.05 0.050 2.40 • • • • • • 0.50-1.80 0.16-0.20 0.07-0.12
GIMY 808 8.00 0.80 0.05 0.050 6.00 • • • • • • 1.00-4.80 0.32-0.56 0.18-0.34
GIMY 1008 10.00 0.80 0.05 0.050 8.00 • • 1.00-6.00 0.35-0.65 0.22-0.40
• DMIN for internal applications =70 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

±.004

GIMY
Utility Single-Ended Inserts 7˚ .197
BW .602 Ref.
for Grooving and Turning CW BW
CW
RE
RE
GIMY 8, 10 GIMY 3

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC8250
IC830

IC808

IC908

IC806

IC804
IC20

IC4

Designation CW RE CWTOL(1) RETOL(2) BW (inch) (IPR) (IPR)

GIMY 304 .118 .016 .0020 .0020 .094 • • • • • • .020-.071 .0063-.0079 .0027-.0047
GIMY 808 .315 .031 .0020 .0020 .236 • • • • • • .039-.189 .0126-.0220 .0071-.0134
GIMY 1008 .394 .031 .0020 .0020 .315 • • .039-.236 .0138-.0256 .0087-.0157
• DMIN for internal applications = 2.76" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

102 ISCAR
 FACE GROOVE-TURN
±0.1
GIMY-F
Utility Single-Ended Inserts 7°
for Grooving and Profiling 15.3 5
Ductile Materials CW BW
RE

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

IC8250
ap f turn f groove

IC808

IC908

IC806

IC804
Designation CW RE CWTOL(1) RETOL(2) BW (mm) (mm/rev) (mm/rev)
GIMY 315F 3.00 1.50 0.05 0.050 2.40 • 0.00-1.50 0.18-0.26 0.07-0.13
GIMY 525F 5.00 2.50 0.05 0.050 3.90 • • 0.00-2.50 0.23-0.42 0.11-0.21
GIMY 630F 6.00 3.00 0.05 0.050 5.00 • • • • 0.00-3.00 0.24-0.50 0.13-0.25
GIMY 840F 8.00 4.00 0.05 0.050 5.60 • 0.00-4.00 0.32-0.67 0.18-0.34
• DMIN for internal applications =70 mm • Can cut arcs to 250° • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

±.004
GIMY-F
Utility Single-Ended Inserts 7°
for Grooving and Profiling .602 .197
Ductile Materials CW BW
RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data
IC8250

ap f turn f groove
IC808

IC908

IC806

IC804

Designation CW RE CWTOL(1) RETOL(2) BW (inch) (IPR) (IPR)

GIMY 315F .118 .059 .0020 .0020 .094 • .000-.059 .0071-.0102 .0028-.0051
GIMY 525F .197 .098 .0020 .0020 .154 • • .000-.098 .0091-.0165 .0043-.0083
GIMY 630F .236 .118 .0020 .0020 .197 • • • • .000-.118 .0094-.0197 .0051-.0098
GIMY 840F .315 .157 .0020 .0020 .220 • .000-.157 .0126-.0264 .0071-.0134
• DMIN for internal applications = 2.76" • Can cut arcs to 250° • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

103
FACE GROOVE-TURN
±0.1
GIMY (full radius)
Utility Single-Ended Inserts 7°
5
for Grooving and Profiling 15.3 Ref.

CW

RE BW

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC8250

IC20N
IC830

IC808

IC908

IC806

IC804
IC20
Designation CW RE CWTOL(1) RETOL(2) BW (mm) (mm/rev) (mm/rev)
GIMY 315 3.00 1.50 0.05 0.050 2.40 • • • • • • • • 0.00-1.50 0.18-0.26 0.07-0.13
GIMY 420 4.00 2.00 0.05 0.050 3.20 • • • • • • • • 0.00-2.00 0.20-0.28 0.09-0.17
GIMY 525 5.00 2.50 0.05 0.050 3.90 • • • • • • • • 0.00-2.50 0.23-0.42 0.11-0.21
GIMY 630 6.00 3.00 0.05 0.050 5.00 • • • • • • • • 0.00-3.00 0.24-0.50 0.13-0.25
GIMY 635-318 6.35 3.18 0.05 0.050 5.10 • • • • 0.00-3.10 0.25-0.53 0.14-0.27
GIMY 840 8.00 4.00 0.05 0.050 5.60 • • • • • 0.00-4.00 0.32-0.67 0.18-0.34
• DMIN for internal application=70 mm • Can cut arcs to 250° • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

±.004
GIMY (full radius)
Utility Single-Ended Inserts 7°
.197
for Grooving and Profiling .602 Ref.

CW
BW
RE

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC8250

IC20N
IC830

IC808

IC908

IC806

IC804
IC20

Designation CW RE CWTOL(1) RETOL(2) BW (inch) (IPR) (IPR)

GIMY 315 .118 .059 .0020 .0020 .094 • • • • • • • • .000-.059 .0071-.0102 .0027-.0051
GIMY 420 .157 .079 .0020 .0020 .126 • • • • • • • • .000-.079 .0079-.0110 .0035-.0067
GIMY 525 .197 .098 .0020 .0020 .154 • • • • • • • • .000-.098 .0091-.0165 .0043-.0083
GIMY 630 .236 .118 .0020 .0020 .197 • • • • • • • • .000-.118 .0094-.0197 .0051-.0098
GIMY 635-318 .250 .125 .0020 .0020 .201 • • • • .000-.122 .0098-.0209 .0055-.0106
GIMY 840 .315 .157 .0020 .0020 .220 • • • • • .000-.157 .0126-.0264 .0071-.0134
• DMIN for internal application= 2.76" • Can cut arcs to 250° • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

104 ISCAR
 FACE GROOVE-TURN
±0.025
30 Ref.
GIPA/GIDA 8 (full radius)
Precision Double-Ended 10° 7° 6.4
Inserts with Polished Top Rake
GIDA 80-40CB CW GIDA 80-40
for Machining Aluminum RE BW

GIPA 8.00-4.00

M E T R I C
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove

IC20

IC4

ID5
Designation CW RE CWTOL(2) RETOL(3) BW (mm) (mm/rev) (mm/rev)
GIDA 80-40 8.00 4.00 0.02 0.050 5.60 • • 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40-D 8.00 4.00 0.02 0.050 5.60 • 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40CB-D (1) 8.00 4.00 0.02 0.050 5.60 • 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40YZ 8.00 4.00 0.02 0.050 5.60 • • 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40YZ-D 8.00 4.00 0.02 0.050 5.60 • 0.00-4.00 0.35-0.96 0.18-0.48
GIPA 8.00-4.00 8.00 4.00 0.02 0.050 6.00 • 0.00-4.00 0.24-0.67 0.14-0.38
• ID5 is a single-ended PCD tipped insert • For cutting speed recommendations and user guide, see pages 161-173
(1) Should not be clamped on tools with "A" suffix
(2) Cutting width tolerance (+/-)
(3) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFGR/L-8 (84)

±.001
1.18 Ref.
GIPA/GIDA 8 (full radius)
Precision Double-Ended 10° 7° .252
Inserts with Polished Top Rake
GIDA 80-40CB CW GIDA 80-40
for Machining Aluminum RE BW

GIPA 8.00-4.00

I N C H
Dimensions Tough 1 Hard Recommended Machining Data

ap f turn f groove
IC20

IC4

ID5

Designation CW RE CWTOL(2) RETOL(3) BW (inch) (IPR) (IPR)

GIDA 80-40 .315 .1575 .0008 .0020 .220 • • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40-D .315 .1575 .0008 .0020 .220 • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40CB-D (1) .315 .1575 .0008 .0020 .220 • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40YZ .315 .1575 .0008 .0020 .220 • • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40YZ-D .315 .1575 .0008 .0020 .220 • .000-.157 .0138-.0378 .0071-.0189
GIPA 8.00-4.00 .315 .1575 .0008 .0020 .236 • .000-.157 .0094-.0264 .0055-.0150
• ID5 is a single-ended PCD tipped insert • For cutting speed recommendations and user guide, see pages 161-173
(1) Should not be clamped on tools with "A" suffix
(2) Cutting width tolerance (+/-)
(3) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87)

105
FACE GROOVE-TURN
±0.025
GIPY
Single-Ended Full Radius Sharp 7°
5
Edged Precision Inserts for 15.3 Ref.
Profiling High Temperature Alloys
CW
RE BW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f turn f groove

IC320

IC806

IC907

IC804
IC20

IC07

IC4
Designation CW RE CWTOL(1) RETOL(2) BW (mm/rev) (mm/rev)
GIPY 3.00-1.50 3.00 1.50 0.02 0.050 2.40 • • • • • • 0.19-0.28 0.08-0.15
GIPY 4.00-2.00 4.00 2.00 0.02 0.050 3.20 • • • • • • 0.22-0.37 0.10-0.20
GIPY 5.00-2.50 5.00 2.50 0.02 0.050 3.90 • • • • • • 0.24-0.46 0.13-0.23
GIPY 6.00-3.00 6.00 3.00 0.02 0.050 5.00 • • • • • 0.26-0.55 0.15-0.27
GIPY 8.00-4.00 8.00 4.00 0.02 0.050 5.60 • • • • • 0.34-0.74 0.20-0.36
• Can cut arcs to 250° • DMIN for internal machining = 70 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

±.001
GIPY
Single-Ended Full Radius Sharp 7°
.197
Edged Precision Inserts for .602 Ref.
Profiling High Temperature Alloys
CW
RE BW

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f turn f groove
IC320

IC806

IC907

IC804
IC20

IC07

IC4

Designation CW RE CWTOL(1) RETOL(2) BW (IPR) (IPR)

GIPY 3.00-1.50 .118 .059 .0008 .0020 .094 • • • • • • .0075-.0110 .0031-.0059
GIPY 4.00-2.00 .157 .079 .0008 .0020 .126 • • • • • • .0087-.0146 .0039-.0079
GIPY 5.00-2.50 .197 .098 .0008 .0020 .154 • • • • • • .0094-.0181 .0051-.0091
GIPY 6.00-3.00 .236 .118 .0008 .0020 .197 • • • • • .0102-.0216 .0059-.0106
GIPY 8.00-4.00 .315 .157 .0008 .0020 .220 • • • • • .0134-.0291 .0079-.0142
• Can cut arcs to 250° • DMIN for internal machining = 2.76" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

106 ISCAR
 FACE GROOVE-TURN
±0.1
GIMM 8CC
Single-Ended Utility Insert with a
.
Frontal Chip Splitter for External 15.3 Ref
Rough Grooving and Side Turning CW BW

RE

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f face-groove

IC808

IC908
Designation CW RE CWTOL(1) RETOL(2) BW (mm/rev)
GIMM 8CC 8.00 0.80 0.05 0.050 5.80 • • 0.30-0.45
• For cutting speed recommendations, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

±.004
GIMM 8CC
Single-Ended Utility Insert with a
.
Frontal Chip Splitter for External .602 Ref
Rough Grooving and Side Turning CW BW

RE

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f face-groove
IC808

IC908
Designation CW RE CWTOL(1) RETOL(2) BW (IPR)
GIMM 8CC .315 .031 .0020 .0020 .228 • • .0118-.0177
• For cutting speed recommendations, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • CGFG 51-P8 (88)

107
FACE GROOVE-TURN
29.95 Ref. CW
GDMM-CC
Single-Ended Utility Insert
for External Rough Grooving RE BW
and Side Turning with a
Frontal Chip Splitter

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data

f face-groove

IC830

IC354

IC808

IC907
Designation CW RE CWTOL(1) RETOL(2) BW (mm/rev)
GDMM 7CC 7.00 0.80 0.05 0.050 6.00 • 0.30-0.45
GDMM 8CC 8.00 0.80 0.05 0.050 5.60 • • • 0.30-0.45
• For cutting speed recommendations, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

1.18 Ref. CW
GDMM-CC
Single-Ended Utility Insert
for External Rough Grooving RE BW
and Side Turning with a
Frontal Chip Splitter

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data

f face-groove
IC830

IC354

IC808

IC907
Designation CW RE CWTOL(1) RETOL(2) BW (IPR)
GDMM 7CC .276 .0315 .0020 .0020 .236 • .0118-.0177
GDMM 8CC .315 .0315 .0020 .0020 .220 • • • .0118-.0177
• For cutting speed recommendations, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)

108 ISCAR
 FACE GROOVE-TURN
TANGFACE
CW
CDX
TNFFH-IQ
Face Grooving Blades
H
HF
DAXN-DAXX

OAL WF
WB_2
Right-hand shown

M E T R I C

Designation CW DAXN(1) DAXX(2) CDX HF H WF WB_2 OAL Insert

TNFFH 65R/L-3IQ 3.00 65.0 90.0 18.00 24.8 32.0 4.10 5.2 150.00 TNF 3... ETF 3-6*
TNFFH 90R/L-3IQ 3.00 90.0 120.0 18.00 24.8 32.0 4.10 5.2 150.00 TNF 3... ETF 3-6*
TNFFH 120R/L-3IQ 3.00 120.0 160.0 24.00 24.8 32.0 4.10 5.2 150.00 TNF 3... ETF 3-6*
TNFFH 80R/L-4IQ 4.00 80.0 150.0 32.00 24.8 32.0 3.80 5.2 150.00 TNF 4... ETF 3-6*
TNFFH 150R/L-4IQ 4.00 150.0 500.0 32.00 24.8 32.0 3.80 5.2 150.00 TNF 4... ETF 3-6*
TNFFH 80R/L-5IQ 5.00 80.0 150.0 30.00 24.8 32.0 3.50 5.2 150.00 TNF 5... ETF 3-6*
TNFFH 150R/L-5IQ 5.00 150.0 500.0 35.00 24.8 32.0 3.50 5.2 150.00 TNF 5... ETF 3-6*
TNFFH 80R/L-6IQ 6.00 80.0 150.0 30.00 24.8 32.0 3.30 5.2 150.00 TNF 6... ETF 3-6*
TNFFH 150R/L-6IQ 6.00 150.0 700.0 35.00 24.8 32.0 3.30 5.2 150.00 TNF 6... ETF 3-6*

I N C H

Designation CW DAXN(1) DAXX(2) CDX HF H WF WB_2 OAL Insert

TNFFH 65R/L-3IQ .118 2.56 3.54 .709 .976 1.260 .161 .205 5.906 TNF 3... ETF 3-6*
TNFFH 90R/L-3IQ .118 3.54 4.72 .709 .976 1.260 .161 .205 5.906 TNF 3... ETF 3-6*
TNFFH 120R/L-3IQ .118 4.72 6.30 .945 .976 1.260 .161 .205 5.906 TNF 3... ETF 3-6*
TNFFH 80R/L-4IQ .157 3.15 5.91 1.260 .976 1.260 .150 .205 5.906 TNF 4... ETF 3-6*
TNFFH 150R/L-4IQ .157 5.91 19.69 1.260 .976 1.260 .150 .205 5.906 TNF 4... ETF 3-6*
TNFFH 80R/L-5IQ .197 3.15 5.91 1.181 .976 1.260 .140 .205 5.906 TNF 5... ETF 3-6*
TNFFH 150R/L-5IQ .197 5.91 19.69 1.378 .976 1.260 .140 .205 5.906 TNF 5... ETF 3-6*
TNFFH 80R/L-6IQ .236 3.15 5.91 1.181 .976 1.260 .130 .205 5.906 TNF 6... ETF 3-6*
TNFFH 150R/L-6IQ .236 5.91 27.56 1.378 .976 1.260 .130 .205 5.906 TNF 6... ETF 3-6*
• H dimension links blades and blocks
(1) Minimum penetration diameter
(2) Maximum penetration diameter

* Optional, should be ordered separately

For inserts, see pages: TNF GN-IQ (112) • TNF-M-IQ (111) • TNF-P-IQ (111)

ETF 3-6 extractor (to be ordered separately)

109
FACE GROOVE-TURN
WF

TNFFA-IQ DAXN-DAXX
Reinforced Face Grooving Blades HF H

OAL WB_2
CW

CDX Right-hand shown

M E T R I C
Designation CW DAXN(1) DAXX(2) CDX H WF HF OAL WB_2 Insert
TNFFA 30R/L-3IQ 3.00 30.0 35.0 19.00 32.0 9.50 24.8 90.00 18.5 TNF 3...
TNFFA 35R/L-3IQ 3.00 35.0 40.0 19.00 32.0 9.50 24.8 90.00 18.5 TNF 3...
TNFFA 40R/L-3IQ 3.00 40.0 46.0 23.00 32.0 9.50 24.8 90.00 18.5 TNF 3...
TNFFA 46R/L-3IQ 3.00 46.0 54.0 25.00 32.0 9.50 24.8 90.00 18.5 TNF 3...
TNFFA 54R/L-3IQ 3.00 54.0 65.0 26.00 32.0 9.50 24.8 90.00 18.5 TNF 3...
TNFFA 65R/L-3IQ 3.00 65.0 80.0 27.00 32.0 9.50 24.8 90.00 18.5 TNF 3...
TNFFA 80R/L-3IQ 3.00 80.0 100.0 27.00 32.0 9.50 24.8 90.00 16.7 TNF 3...
TNFFA 35R/L-4IQ 4.00 35.0 45.0 25.00 32.0 9.00 24.8 90.00 18.1 TNF 4...
TNFFA 45R/L-4IQ 4.00 45.0 60.0 25.00 32.0 9.00 24.8 90.00 17.3 TNF 4...
TNFFA 60R/L-4IQ 4.00 60.0 80.0 27.00 32.0 9.00 24.8 90.00 18.0 TNF 4...
TNFFA 80R/L-4IQ 4.00 80.0 130.0 27.00 32.0 9.00 24.8 90.00 14.8 TNF 4...
TNFFA 40R/L-5IQ 5.00 40.0 50.0 25.00 32.0 9.70 24.8 90.00 18.0 TNF 5...
TNFFA 50R/L-5IQ 5.00 50.0 70.0 28.00 32.0 9.70 24.8 90.00 18.0 TNF 5...
TNFFA 70R/L-5IQ 5.00 70.0 100.0 30.00 32.0 9.70 24.8 90.00 18.0 TNF 5...
TNFFA 100R/L-5IQ 5.00 100.0 180.0 35.00 32.0 9.70 24.8 90.00 18.0 TNF 5...
TNFFA 45R/L-6IQ 6.00 45.0 60.0 25.00 32.0 10.20 24.8 90.00 18.0 TNF 6...
TNFFA 60R/L-6IQ 6.00 60.0 80.0 28.00 32.0 10.20 24.8 90.00 18.0 TNF 6...
TNFFA 80R/L-6IQ 6.00 80.0 110.0 30.00 32.0 10.20 24.8 90.00 18.0 TNF 6...
TNFFA 110R/L-6IQ 6.00 110.0 300.0 35.00 32.0 10.20 24.8 90.00 14.8 TNF 6...

I N C H
Designation CW DAXN(1) DAXX(2) CDX H WF HF OAL WB_2 Insert
TNFFA 30R/L-3IQ .118 1.18 1.38 .748 1.260 .374 .976 3.543 .728 TNF 3...
TNFFA 35R/L-3IQ .118 1.38 1.57 .748 1.260 .374 .976 3.543 .728 TNF 3...
TNFFA 40R/L-3IQ .118 1.57 1.81 .906 1.260 .374 .976 3.543 .728 TNF 3...
TNFFA 46R/L-3IQ .118 1.81 2.13 .984 1.260 .374 .976 3.543 .728 TNF 3...
TNFFA 54R/L-3IQ .118 2.13 2.56 1.024 1.260 .374 .976 3.543 .728 TNF 3...
TNFFA 65R/L-3IQ .118 2.56 3.15 1.063 1.260 .374 .976 3.543 .728 TNF 3...
TNFFA 80R/L-3IQ .118 3.15 3.94 1.063 1.260 .374 .976 3.543 .657 TNF 3...
TNFFA 35R/L-4IQ .157 1.38 1.77 .984 1.260 .354 .976 3.543 .713 TNF 4...
TNFFA 45R/L-4IQ .157 1.77 2.36 .984 1.260 .354 .976 3.543 .681 TNF 4...
TNFFA 60R/L-4IQ .157 2.36 3.15 1.063 1.260 .354 .976 3.543 .709 TNF 4...
TNFFA 80R/L-4IQ .157 3.15 5.12 1.063 1.260 .354 .976 3.543 .583 TNF 4...
TNFFA 40R/L-5IQ .197 1.57 1.97 .984 1.260 .382 .976 3.543 .709 TNF 5...
TNFFA 50R/L-5IQ .197 1.97 2.76 1.102 1.260 .382 .976 3.543 .709 TNF 5...
TNFFA 70R/L-5IQ .197 2.76 3.94 1.181 1.260 .382 .976 3.543 .709 TNF 5...
TNFFA 100R/L-5IQ .197 3.94 7.09 1.378 1.260 .382 .976 3.543 .709 TNF 5...
TNFFA 45R/L-6IQ .236 1.77 2.36 .984 1.260 .402 .976 3.543 .709 TNF 6...
TNFFA 60R/L-6IQ .236 2.36 3.15 1.102 1.260 .402 .976 3.543 .709 TNF 6...
TNFFA 80R/L-6IQ .236 3.15 4.33 1.181 1.260 .402 .976 3.543 .709 TNF 6...
TNFFA 110R/L-6IQ .236 4.33 11.81 1.378 1.260 .402 .976 3.543 .583 TNF 6...
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: TNF GN-IQ (112) • TNF-M-IQ (111) • TNF-P-IQ (111)

Spare Parts

Designation
TNFFA-IQ ETF 3-6*
* Optional, should be ordered separately

110 ISCAR
 FACE GROOVE-TURN
CW RE
TNF-P-IQ
Face Grooving Single-Ended
Inserts for Machining Steel

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC808
Designation CW RE CWTOL(1) (mm/rev)
TNF 3P-IQ 3.00 0.30 0.05 • 0.10-0.15
TNF 4P-IQ 4.00 0.25 0.05 • 0.10-0.15
TNF 5P-IQ 5.00 0.35 0.05 • 0.12-0.20
TNF 6P-IQ 6.00 0.35 0.05 • 0.12-0.20

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC808
Designation CW RE CWTOL(1) (IPR)
TNF 3P-IQ .118 .0118 .0020 • .0039-.0059
TNF 4P-IQ .157 .0098 .0020 • .0039-.0059
TNF 5P-IQ .197 .0138 .0020 • .0047-.0079
TNF 6P-IQ .236 .0138 .0020 • .0047-.0079
• For user guide, see pages 161-173
(1) Cutting width tolerance (+/-)

For tools, see pages: TNFFA-IQ (110) • TNFFH-IQ (109) • TNFPAD-XL-JHP (113)

CW RE
TNF-M-IQ
Face Grooving Single-Ended
Inserts for Machining Stainless
Steel and High Temperature Alloys

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove
IC808

Designation CW RE CWTOL(1) (mm/rev)

TNF 3M-IQ 3.00 0.30 0.05 • 0.08-0.10
TNF 4M-IQ 4.00 0.25 0.05 • 0.08-0.12
TNF 5M-IQ 5.00 0.35 0.05 • 0.12-0.20
TNF 6M-IQ 6.00 0.35 0.05 • 0.12-0.20

I N C H
Recommended
Dimensions
Machining Data

f face-groove
IC808

Designation CW RE CWTOL(1) (IPR)

TNF 3M-IQ .118 .0118 .0020 • .0031-.0039
TNF 4M-IQ .157 .0098 .0020 • .0031-.0047
TNF 5M-IQ .197 .0138 .0020 • .0047-.0079
TNF 6M-IQ .236 .0138 .0020 • .0047-.0079
• For user guide, see pages 161-173
(1) Cutting width tolerance (+/-)

For tools, see pages: TNFFA-IQ (110) • TNFFH-IQ (109) • TNFPAD-XL-JHP (113)

111
FACE GROOVE-TURN
RE CW
TNF GN-IQ
Face Grooving Single-Ended
Inserts for Machining Steel

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC808
Designation CW RE CWTOL(1) (mm/rev)
TNF 3GN-IQ 3.00 0.30 0.05 • 0.06-0.10
TNF 4GN-IQ 4.00 0.40 0.05 • 0.06-0.12
TNF 5GN-IQ 5.00 0.40 0.05 • 0.08-0.16
TNF 6GN-IQ 6.00 0.40 0.05 • 0.08-0.20

I N C H
Recommended
Dimensions
Machining Data

f face-groove

IC808
Designation CW RE CWTOL(1) (IPR)
TNF 3GN-IQ .118 .0118 .0020 • .0024-.0039
TNF 4GN-IQ .157 .0157 .0020 • .0024-.0047
TNF 5GN-IQ .197 .0157 .0020 • .0031-.0063
TNF 6GN-IQ .236 .0157 .0020 • .0031-.0079
• For user guide, see pages 161-173
(1) Cutting width tolerance (+/-)

For tools, see pages: TNFFA-IQ (110) • TNFFH-IQ (109) • TNFPAD-XL-JHP (113)

112 ISCAR
 FACE GROOVE-TURN
CDX

OAH ØDAXN-DAXX
HF

TNFPAD-XL-JHP OAL
Adapters for Face Machining WF CW WB

Right-hand shown

M E T R I C
Designation CW CDX WF WB OAL HF OAH DAXN(1) DAXX(2)
TNFPAD-XL 4L-35T20-JHP 4.00 20.00 8.00 9.50 65.00 34.0 43.00 35.0 53.0
TNFPAD-XL 4L-45T20-JHP 4.00 20.00 8.00 9.50 65.00 34.0 43.00 45.0 68.0
TNFPAD-XL 4R/L-35T35-JHP 4.00 35.00 8.00 9.50 80.00 34.0 43.00 35.0 53.0
TNFPAD-XL 4R/L-45T35-JHP 4.00 35.00 8.00 9.50 80.00 34.0 43.00 45.0 68.0
TNFPAD-XL 5L-60T20-JHP 5.00 20.00 8.00 10.00 65.00 34.0 43.00 60.0 90.0
TNFPAD-XL 5R/L-60T40-JHP 5.00 40.00 8.00 10.00 85.00 34.0 43.00 60.0 90.0
TNFPAD-XL 6L-110T20-JHP 6.00 20.00 8.00 10.50 65.00 34.0 43.00 110.0 312.0
TNFPAD-XL 6L-80T20-JHP 6.00 20.00 8.00 10.50 65.00 34.0 43.00 80.0 122.0
TNFPAD-XL 6L-80T45-JHP 6.00 45.00 8.00 10.50 90.00 34.0 43.00 80.0 122.0
TNFPAD-XL 6R/L-110T50-JHP 6.00 50.00 8.00 10.50 95.00 34.0 43.00 110.0 312.0

I N C H
Designation CW CDX WF WB OAL HF OAH DAXN(1) DAXX(2)
TNFPAD-XL 4L-35T20-JHP .157 .787 .315 .374 2.559 1.339 1.693 1.38 2.09
TNFPAD-XL 4L-45T20-JHP .157 .787 .315 .374 2.559 1.339 1.693 1.77 2.68
TNFPAD-XL 4R/L-35T35-JHP .157 1.378 .315 .374 3.150 1.339 1.693 1.38 2.09
TNFPAD-XL 4R/L-45T35-JHP .157 1.378 .315 .374 3.150 1.339 1.693 1.77 2.68
TNFPAD-XL 5L-60T20-JHP .197 .787 .315 .394 2.559 1.339 1.693 2.36 3.54
TNFPAD-XL 5R/L-60T40-JHP .197 1.575 .315 .394 3.346 1.339 1.693 2.36 3.54
TNFPAD-XL 6L-110T20-JHP .236 .787 .315 .413 2.559 1.339 1.693 4.33 12.28
TNFPAD-XL 6L-80T20-JHP .236 .787 .315 .413 2.559 1.339 1.693 3.15 4.80
TNFPAD-XL 6L-80T45-JHP .236 1.772 .315 .413 3.543 1.339 1.693 3.15 4.80
TNFPAD-XL 6R/L-110T50-JHP .236 1.968 .315 .413 3.740 1.339 1.693 4.33 12.28
• WF(assembly)=WF(shank) + WF(adapter) • TNF 4..5..6 inserts can be used with left and right hand adapters. • For user guide, see pages 161-173
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter

For inserts, see pages: TNF GN-IQ (112) • TNF-M-IQ (111) • TNF-P-IQ (111)
For holders, see pages: IH-TNFPAD (114) • MAHPR/L-XL-JHP (155) • MAHR/L-MG-XL-JHP (159) • MAHR/L-MG-XL-JHP-MC (160)

Spare Parts

Designation
TNFPAD-XL-JHP ETF 3-6

113
FACE GROOVE-TURN
A View A
OAL
IH-TNFPAD
Intermediate Serrated Cartridge
for Standard TANG FACE OAW
TNFPAD-XL R Adapters OAH

M E T R I C
Designation OAH OAW OAL
IH-TNFPAD 54.00 73.00 65.70
For tools, see pages: TNFPAD-XL-JHP (113)

HSK63 HATA + IH-TNFPAD

C6 HATA + IH-TNFPAD HSK63/C6 HATA

DAX
CW

IH-TNFPAD
CDX

Adapter

Designation CW (min) CW (max) CDX DAX (min) DAX (max)

TNFPAD-XL 4L-35T20-JHP 4.00 6.90 20.00 35.0 53.0
TNFPAD-XL 4L-45T20-JHP 4.00 6.90 20.00 45.0 68.0
TNFPAD-XL 4R/L-35T35-JHP 4.00 6.90 35.00 35.0 53.0
TNFPAD-XL 4R/L-45T35-JHP 4.00 6.90 35.00 45.0 68.0
TNFPAD-XL 5L-60T20-JHP 5.00 8.90 20.00 60.0 90.0
TNFPAD-XL 5R/L-60T40-JHP 5.00 8.90 40.00 60.0 90.0
TNFPAD-XL 6L-110T20-JHP 6.00 10.90 20.00 110.0 312.0
TNFPAD-XL 6L-80T20-JHP 6.00 10.90 20.00 80.0 122.0
TNFPAD-XL 6L-80T45-JHP 6.00 10.90 45.00 80.0 122.0
TNFPAD-XL 6R/L-110T50-JHP 6.00 10.90 50.00 110.0 312.0

Spare Parts

Designation
IH-TNFPAD SR M6X14-XT DIN 912 BLD T20/M7 SW6-SD SR M5-04451 SR M6X20-XT O-RING 19X2 NBR HW 5.0 OR 5X1N T-20/5

114 ISCAR
 FACE GROOVE-TURN
SELF-GRIP
SGFFR/L CDX
CW
Face Grooving Integral
Shank Tools DAXN-DAXX HF H

OAL B

Left-hand shown

M E T R I C

Designation CW H B CDX DAXN(1) DAXX(2) HF OAL Insert

SGFFR/L 20-25-2 2.10 20.0 20.0 13.00 25.0 30.0 20.0 120.00 GFF 2R/L SET ESG 0.5
SGFFR/L 20-30-2 2.10 20.0 20.0 14.00 29.0 36.0 20.0 120.00 GFF 2R/L ESG 0.5
SGFFR/L 20-35-2 2.10 20.0 20.0 16.00 35.0 46.0 20.8 120.00 GFF 2N ESG 0.5
SGFFR/L 20-45-2 2.10 20.0 20.0 20.00 45.0 61.0 20.8 120.00 GFF 2N ESG 0.5
SGFFR/L 20-60-2 2.10 20.0 20.0 20.00 60.0 80.0 20.8 120.00 GFF 2N ESG 0.5
SGFFR/L 25-35-2 2.10 25.0 25.0 16.00 35.0 46.0 25.8 130.00 GFF 2N ESG 0.5
SGFFR/L 25-45-2 2.10 25.0 25.0 20.00 45.0 61.0 25.8 130.00 GFF 2N ESG 0.5
SGFFR/L 25-60-2 2.10 25.0 25.0 20.00 60.0 80.0 25.8 130.00 GFF 2N ESG 0.5
SGFFR 25-25-2 2.10 25.0 25.0 13.00 25.0 30.0 25.0 130.00 GFF 2N ESG 0.5
SGFFR 25-30-2 2.10 25.0 25.0 14.00 29.0 36.0 25.0 130.00 GFF 2N ESG 0.5
SGFFR/L 20-30-3 3.00 20.0 20.0 16.00 30.0 35.0 20.0 120.00 GFF 3R/L SET ESG 1
SGFFR 20-35-3 3.00 20.0 20.0 18.00 34.4 40.6 20.0 120.00 GFF 3R/L SET ESG 1
SGFFR 20-40-3 3.00 20.0 20.0 20.00 40.0 47.0 20.0 120.00 GFF 3R/L SET ESG 1
SGFFR 20-46-3 3.00 20.0 20.0 22.00 46.0 55.0 20.0 120.00 GFF 3R/L SET ESG 1
SGFFR 20-55-3 3.00 20.0 20.0 22.00 54.0 65.0 21.2 120.00 GFF 3N SET ESG 1
SGFFR 20-65-3 3.00 20.0 20.0 23.00 64.0 80.0 21.0 120.00 GFF 3N SET ESG 1
SGFFR 20-80-3 3.00 20.0 20.0 24.00 79.0 100.0 20.7 120.00 GFF 3N SET ESG 1
SGFFR/L 25-40-3 3.00 25.0 25.0 20.00 40.0 47.0 25.0 130.00 GFF 3R/L SET ESG 1
SGFFR/L 25-55-3 3.00 25.0 25.0 24.00 54.0 65.0 26.2 130.00 GFF 3N SET ESG 1
SGFFR 25-30-3 3.00 25.0 25.0 16.00 30.0 35.0 25.0 130.00 GFF 3R/L SET ESG 1
SGFFR 25-35-3 3.00 25.0 25.0 18.00 34.4 40.6 25.0 130.00 GFF 3R/L SET ESG 1
SGFFR 25-46-3 3.00 25.0 25.0 22.00 46.0 55.0 25.0 130.00 GFF 3R/L SET ESG 1
SGFFR 25-65-3 3.00 25.0 25.0 25.00 64.0 80.0 26.0 130.00 GFF 3N SET ESG 1
SGFFR 25-80-3 3.00 25.0 25.0 26.00 79.0 100.0 25.7 130.00 GFF 3N SET ESG 1
SGFFR/L 20-35-4 4.00 20.0 20.0 20.00 35.0 45.0 20.0 120.00 GFF 4N SET ESG 1
SGFFR 20-45-4 4.00 20.0 20.0 25.00 44.0 58.0 20.0 120.00 GFF 4N SET ESG 1
SGFFR 20-60-4 4.00 20.0 20.0 25.00 57.0 80.0 20.0 120.00 GFF 4N SET ESG 1
SGFFR 20-80-4 4.00 20.0 20.0 25.00 79.0 130.0 20.0 120.00 GFF 4N SET ESG 1
SGFFR/L 25-45-4 4.00 25.0 25.0 25.00 44.0 58.0 25.0 150.00 GFF 4N SET ESG 1
SGFFR/L 25-60-4 4.00 25.0 25.0 26.00 57.0 80.0 25.0 150.00 GFF 4N SET ESG 1
SGFFR/L 25-80-4 4.00 25.0 25.0 26.00 79.0 130.0 25.0 150.00 GFF 4N SET ESG 1
SGFFR 25-35-4 4.00 25.0 25.0 20.00 35.0 45.0 25.0 150.00 GFF 4N SET ESG 1
SGFFR/L 20-50-5 5.00 20.0 20.0 25.00 50.0 75.0 20.0 120.00 GFF 5N SET ESG 1
SGFFR 20-75-5 5.00 20.0 20.0 26.00 74.0 130.0 20.0 120.00 GFF 5N SET ESG 1
SGFFR/L 25-100-5 5.00 25.0 25.0 30.00 100.0 180.0 25.0 150.00 GFF 5N SET ESG 1
SGFFR 25-50-5 5.00 25.0 25.0 26.00 50.0 71.0 25.0 150.00 GFF 5N SET ESG 1
SGFFR 25-70-5 5.00 25.0 25.0 28.00 69.0 102.0 25.0 150.00 GFF 5N SET ESG 1
SGFFR 20-60-6 6.00 20.0 20.0 25.00 57.0 60.0 20.0 120.00 GFF 6N SET ESG 1
SGFFR/L 25-100-6 6.00 25.0 25.0 30.00 100.0 180.0 25.0 150.00 GFF 6N SET ESG 1
SGFFR/L 25-60-6 6.00 25.0 25.0 30.00 57.0 77.0 25.0 150.00 GFF 6N SET ESG 1
SGFFR/L 25-75-6 6.00 25.0 25.0 30.00 75.0 102.0 25.0 150.00 GFF 6N SET ESG 1
• Important: Apply R.H. insert on R.H. tool and L.H. insert on L.H. tool. Neutral insert only as indicated
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GFF-N (121) • GFF-R/L (121)

115
FACE GROOVE-TURN

SGFFR/L CDX
CW
Face Grooving Integral
Shank Tools DAXN-DAXX HF H

OAL B

Left-hand shown

I N C H

Designation CW H B CDX DAXN(1) DAXX(2) HF OAL Insert

SGFFR/L 20-25-2 .083 .787 .787 .512 .98 1.18 .787 4.724 GFF 2R/L SET ESG 0.5
SGFFR/L 20-30-2 .083 .787 .787 .551 1.14 1.42 .787 4.724 GFF 2R/L ESG 0.5
SGFFR/L 20-35-2 .083 .787 .787 .630 1.38 1.81 .819 4.724 GFF 2N ESG 0.5
SGFFR/L 20-45-2 .083 .787 .787 .787 1.77 2.40 .819 4.724 GFF 2N ESG 0.5
SGFFR/L 20-60-2 .083 .787 .787 .787 2.36 3.15 .819 4.724 GFF 2N ESG 0.5
SGFFR/L 25-35-2 .083 .984 .984 .630 1.38 1.81 1.016 5.118 GFF 2N ESG 0.5
SGFFR/L 25-45-2 .083 .984 .984 .787 1.77 2.40 1.016 5.118 GFF 2N ESG 0.5
SGFFR/L 25-60-2 .083 .984 .984 .787 2.36 3.15 1.016 5.118 GFF 2N ESG 0.5
SGFFR 25-25-2 .083 .984 .984 .512 .98 1.18 .984 5.118 GFF 2N ESG 0.5
SGFFR 25-30-2 .083 .984 .984 .551 1.14 1.42 .984 5.118 GFF 2N ESG 0.5
SGFFR/L 20-30-3 .118 .787 .787 .630 1.18 1.38 .787 4.724 GFF 3R/L SET ESG 1
SGFFR 20-35-3 .118 .787 .787 .709 1.35 1.60 .787 4.724 GFF 3R/L SET ESG 1
SGFFR 20-40-3 .118 .787 .787 .787 1.57 1.85 .787 4.724 GFF 3R/L SET ESG 1
SGFFR 20-46-3 .118 .787 .787 .866 1.81 2.17 .787 4.724 GFF 3R/L SET ESG 1
SGFFR 20-55-3 .118 .787 .787 .866 2.13 2.56 .835 4.724 GFF 3N SET ESG 1
SGFFR 20-65-3 .118 .787 .787 .906 2.52 3.15 .827 4.724 GFF 3N SET ESG 1
SGFFR 20-80-3 .118 .787 .787 .945 3.11 3.94 .815 4.724 GFF 3N SET ESG 1
SGFFR/L 25-40-3 .118 .984 .984 .787 1.57 1.85 .984 5.118 GFF 3R/L SET ESG 1
SGFFR/L 25-55-3 .118 .984 .984 .945 2.13 2.56 1.031 5.118 GFF 3N SET ESG 1
SGFFR 25-30-3 .118 .984 .984 .630 1.18 1.38 .984 5.118 GFF 3R/L SET ESG 1
SGFFR 25-35-3 .118 .984 .984 .709 1.35 1.60 .984 5.118 GFF 3R/L SET ESG 1
SGFFR 25-46-3 .118 .984 .984 .866 1.81 2.17 .984 5.118 GFF 3R/L SET ESG 1
SGFFR 25-65-3 .118 .984 .984 .984 2.52 3.15 1.024 5.118 GFF 3N SET ESG 1
SGFFR 25-80-3 .118 .984 .984 1.024 3.11 3.94 1.012 5.118 GFF 3N SET ESG 1
SGFFR/L 20-35-4 .157 .787 .787 .787 1.38 1.77 .787 4.724 GFF 4N SET ESG 1
SGFFR 20-45-4 .157 .787 .787 .984 1.73 2.28 .787 4.724 GFF 4N SET ESG 1
SGFFR 20-60-4 .157 .787 .787 .984 2.24 3.15 .787 4.724 GFF 4N SET ESG 1
SGFFR 20-80-4 .157 .787 .787 .984 3.11 5.12 .787 4.724 GFF 4N SET ESG 1
SGFFR/L 25-45-4 .157 .984 .984 .984 1.73 2.28 .984 5.906 GFF 4N SET ESG 1
SGFFR/L 25-60-4 .157 .984 .984 1.024 2.24 3.15 .984 5.906 GFF 4N SET ESG 1
SGFFR/L 25-80-4 .157 .984 .984 1.024 3.11 5.12 .984 5.906 GFF 4N SET ESG 1
SGFFR 25-35-4 .157 .984 .984 .787 1.38 1.77 .984 5.906 GFF 4N SET ESG 1
SGFFR/L 20-50-5 .197 .787 .787 .984 1.97 2.95 .787 4.724 GFF 5N SET ESG 1
SGFFR 20-75-5 .197 .787 .787 1.024 2.91 5.12 .787 4.724 GFF 5N SET ESG 1
SGFFR/L 25-100-5 .197 .984 .984 1.181 3.94 7.09 .984 5.906 GFF 5N SET ESG 1
SGFFR 25-50-5 .197 .984 .984 1.024 1.97 2.80 .984 5.906 GFF 5N SET ESG 1
SGFFR 25-70-5 .197 .984 .984 1.102 2.72 4.02 .984 5.906 GFF 5N SET ESG 1
SGFFR 20-60-6 .236 .787 .787 .984 2.24 2.36 .787 4.724 GFF 6N SET ESG 1
SGFFR/L 25-100-6 .236 .984 .984 1.181 3.94 7.09 .984 5.906 GFF 6N SET ESG 1
SGFFR/L 25-60-6 .236 .984 .984 1.181 2.24 3.03 .984 5.906 GFF 6N SET ESG 1
SGFFR/L 25-75-6 .236 .984 .984 1.181 2.95 4.02 .984 5.906 GFF 6N SET ESG 1
• Important: Apply R.H. insert on R.H. tool and L.H. insert on L.H. tool. Neutral insert only as indicated
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GFF-N (121) • GFF-R/L (121)

116 ISCAR
 FACE GROOVE-TURN
HF
SGFFA
Reinforced Face Grooving Blades H
for Standard Tool Blocks DAXN-DAXX CW

CDX
OAL
Right-hand shown

M E T R I C
Designation CW CDX DAXN(1) DAXX(2) H HF OAL
SGFFA 25-R/L-2 2.10 13.00 25.0 30.0 32.0 0.0 80.00
SGFFA 30-L-2 2.10 14.00 29.0 36.0 32.0 0.0 80.00
SGFFA 35-L-2 2.10 16.00 35.0 46.0 32.0 0.8 80.00
SGFFA 45-L-2 2.10 20.00 45.0 61.0 32.0 0.8 80.00
SGFFA 60-L-2 2.10 20.00 60.0 80.0 32.0 0.8 80.00
SGFFA 80-L-2 2.10 20.00 79.0 102.0 32.0 0.8 80.00
SGFFA 35-L-3 3.00 20.00 34.4 40.6 32.0 0.0 90.00
SGFFA 40-L-3 3.00 22.00 40.0 47.0 32.0 0.0 90.00
SGFFA 46-L-3 3.00 24.00 46.0 55.0 32.0 0.0 90.00
SGFFA 55-L-3 3.00 25.00 54.0 65.0 32.0 1.2 90.00
SGFFA 65-L-3 3.00 26.00 64.0 80.0 32.0 1.0 90.00
SGFFA 80-L-3 3.00 28.00 79.0 100.0 32.0 0.7 95.00
SGFFA 35-L-4 4.00 25.00 35.0 45.0 32.0 0.0 90.00
SGFFA 45-R/L-4 4.00 25.00 44.0 58.0 32.0 0.0 90.00
SGFFA 40-R/L-5 5.00 25.00 40.0 52.0 32.0 0.0 90.00
SGFFA 50-R/L-5 5.00 28.00 50.0 71.0 32.0 0.0 95.00
SGFFA 70-L-5 5.00 30.00 69.0 102.0 32.0 0.0 95.00
SGFFA 100-L-5 5.00 35.00 100.0 180.0 32.0 0.0 100.00
SGFFA 45-R/L-6 6.00 25.00 44.0 58.0 32.0 0.0 90.00
SGFFA 60-L-6 6.00 30.00 57.0 77.0 32.0 0.0 95.00
SGFFA 75-R/L-6 6.00 35.00 75.0 102.0 32.0 0.0 100.00
• Important: Apply R.H. insert on R.H. tool and L.H. insert on L.H. tool. Neutral insert only as indicated • H dimension links blades and blocks
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GFF-N (121) • GFF-R/L (121)

For holders, see pages: SGTBF (136) • SGTBU/SGTBN (133) • UBHCR/L (135)

Spare Parts

Designation
SGFFA 25-L-2 SET ESG 0.5
SGFFA 25-R-2 ESG 0.5
SGFFA 30-L-2 ESG 0.5
SGFFA 35-L-2 ESG 0.5
SGFFA 45-L-2 ESG 0.5
SGFFA 60-L-2 ESG 0.5
SGFFA 80-L-2 ESG 0.5
SGFFA 35-L-3 SET ESG 1
SGFFA 40-L-3 SET ESG 1
SGFFA 46-L-3 SET ESG 1
SGFFA 55-L-3 SET ESG 1
SGFFA 65-L-3 SET ESG 1
SGFFA 80-L-3 SET ESG 1
SGFFA 35-L-4 SET ESG 1
SGFFA 45-R/L-4 SET ESG 1
SGFFA 40-R/L-5 SET ESG 1
SGFFA 50-R/L-5 SET ESG 1
SGFFA 70-L-5 SET ESG 1
SGFFA 100-L-5 SET ESG 1
SGFFA 45-R/L-6 SET ESG 1
SGFFA 60-L-6 SET ESG 1
SGFFA 75-R/L-6 SET ESG 1

117
FACE GROOVE-TURN
HF
SGFFA
Reinforced Face Grooving Blades H
for Standard Tool Blocks DAXN-DAXX CW

CDX
OAL
Right-hand shown

I N C H
Designation CW CDX DAXN(1) DAXX(2) H HF OAL
SGFFA 25-R/L-2 .083 .512 .98 1.18 1.260 .000 3.150
SGFFA 30-L-2 .083 .551 1.14 1.42 1.260 .000 3.150
SGFFA 35-L-2 .083 .630 1.38 1.81 1.260 .031 3.150
SGFFA 45-L-2 .083 .787 1.77 2.40 1.260 .031 3.150
SGFFA 60-L-2 .083 .787 2.36 3.15 1.260 .031 3.150
SGFFA 80-L-2 .083 .787 3.11 4.02 1.260 .031 3.150
SGFFA 35-L-3 .118 .787 1.35 1.60 1.260 .000 3.543
SGFFA 40-L-3 .118 .866 1.57 1.85 1.260 .000 3.543
SGFFA 46-L-3 .118 .945 1.81 2.17 1.260 .000 3.543
SGFFA 55-L-3 .118 .984 2.13 2.56 1.260 .047 3.543
SGFFA 65-L-3 .118 1.024 2.52 3.15 1.260 .039 3.543
SGFFA 80-L-3 .118 1.102 3.11 3.94 1.260 .028 3.740
SGFFA 35-L-4 .157 .984 1.38 1.77 1.260 .000 3.543
SGFFA 45-R/L-4 .157 .984 1.73 2.28 1.260 .000 3.543
SGFFA 40-R/L-5 .197 .984 1.57 2.05 1.260 .000 3.543
SGFFA 50-R/L-5 .197 1.102 1.97 2.80 1.260 .000 3.740
SGFFA 70-L-5 .197 1.181 2.72 4.02 1.260 .000 3.740
SGFFA 100-L-5 .197 1.378 3.94 7.09 1.260 .000 3.937
SGFFA 45-R/L-6 .236 .984 1.73 2.28 1.260 .000 3.543
SGFFA 60-L-6 .236 1.181 2.24 3.03 1.260 .000 3.740
SGFFA 75-R/L-6 .236 1.378 2.95 4.02 1.260 .000 3.937
• Important: Apply R.H. insert on R.H. tool and L.H. insert on L.H. tool. Neutral insert only as indicated • H dimension links blades and blocks
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GFF-N (121) • GFF-R/L (121)

For holders, see pages: SGTBF (136) • SGTBU/SGTBN (133) • UBHCR/L (135)

Spare Parts

Designation
SGFFA 25-L-2 SET ESG 0.5
SGFFA 25-R-2 ESG 0.5
SGFFA 30-L-2 ESG 0.5
SGFFA 35-L-2 ESG 0.5
SGFFA 45-L-2 ESG 0.5
SGFFA 60-L-2 ESG 0.5
SGFFA 80-L-2 ESG 0.5
SGFFA 35-L-3 SET ESG 1
SGFFA 40-L-3 SET ESG 1
SGFFA 46-L-3 SET ESG 1
SGFFA 55-L-3 SET ESG 1
SGFFA 65-L-3 SET ESG 1
SGFFA 80-L-3 SET ESG 1
SGFFA 35-L-4 SET ESG 1
SGFFA 45-R/L-4 SET ESG 1
SGFFA 40-R/L-5 SET ESG 1
SGFFA 50-R/L-5 SET ESG 1
SGFFA 70-L-5 SET ESG 1
SGFFA 100-L-5 SET ESG 1
SGFFA 45-R/L-6 SET ESG 1
SGFFA 60-L-6 SET ESG 1
SGFFA 75-R/L-6 SET ESG 1

118 ISCAR
 FACE GROOVE-TURN
CW CW
CW
SGFFH CDX
HF
Face Grooving Blades H
DAXN-DAXX H

WB_2 WB_2 OAL

WB_2
SGFFH..L-6 SGFFH..R-6

M E T R I C
Designation CW CDX DAXN(1) DAXX(2) HF H WB_2 OAL
SGFFH 35-R/L-2 2.10 20.00 35.0 46.0 0.8 32.0 5.2 150.00
SGFFH 45-R/L-2 2.10 20.00 45.0 61.0 0.8 32.0 5.2 150.00
SGFFH 60-R-2 2.10 20.00 60.0 80.0 0.8 32.0 5.2 150.00
SGFFH 80-R/L-2 2.10 20.00 79.0 102.0 0.8 32.0 4.0 150.00
SGFFH 100-R/L-2 2.10 20.00 101.0 132.0 0.0 32.0 4.0 150.00
SGFFH 75-R/L-3 3.00 20.00 65.0 92.0 1.0 32.0 5.2 150.00
SGFFH 90-R/L-3 3.00 20.00 90.0 122.0 0.2 32.0 5.2 150.00
SGFFH 120-R/L-3 3.00 25.00 120.0 160.0 0.0 32.0 5.2 150.00
SGFFH 80-R/L-4 4.00 30.00 80.0 155.0 2.5 32.0 5.2 150.00
SGFFH 150-R/L-4 4.00 30.00 150.0 500.0 2.5 32.0 5.2 150.00
SGFFH 80-R/L-5 5.00 32.00 80.0 162.0 0.0 32.0 5.2 150.00
SGFFH 150-R/L-5 5.00 35.00 150.0 600.0 0.0 32.0 5.2 150.00
SGFFH 90-R/L-6 6.00 32.00 90.0 150.0 0.0 32.0 8.0 150.00
SGFFH 150-R/L-6 6.00 35.00 148.0 700.0 0.0 32.0 5.2 150.00
• Important: Apply R.H. insert on R.H. tool and L.H. insert on L.H. tool. Neutral insert only as indicated • H dimension links blades and blocks
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GFF-N (121)

For holders, see pages: SGTBF (136) • SGTBK (135) • SGTBU/SGTBN (133) • UBHCR/L (135)

Spare Parts

Designation
SGFFH 35-L-2 SET ESG 0.5
SGFFH 35-R-2 ESG 0.5
SGFFH 45-L-2 SET ESG 0.5
SGFFH 45-R-2 ESG 0.5
SGFFH 60-R-2 ESG 0.5
SGFFH 80-L-2 ESG 0.5
SGFFH 80-R-2 ESG 0.5
SGFFH 100-L-2 SET ESG 0.5
SGFFH 100-R-2 SET ESG 0.5
SGFFH 75-L-3 SET ESG 1
SGFFH 75-R-3 SET ESG 1
SGFFH 90-L-3 SET ESG 1
SGFFH 90-R-3 SET ESG 1
SGFFH 120-L-3 SET ESG 1
SGFFH 120-R-3 SET ESG 1
SGFFH 80-L-4 SET ESG 1
SGFFH 80-R-4 SET ESG 1
SGFFH 150-L-4 SET ESG 1
SGFFH 150-R-4 SET ESG 1
SGFFH 80-L-5 SET ESG 1
SGFFH 80-R-5 SET ESG 1
SGFFH 150-L-5 SET ESG 1
SGFFH 150-R-5 SET ESG 1
SGFFH 90-L-6 SET ESG 1
SGFFH 90-R-6 SET ESG 1
SGFFH 150-L-6 SET ESG 1
SGFFH 150-R-6 SET ESG 1

119
FACE GROOVE-TURN
CW CW
CW
SGFFH CDX
HF
Face Grooving Blades H
DAXN-DAXX H

WB_2 WB_2 OAL

WB_2
SGFFH..L-6 SGFFH..R-6

I N C H
Designation CW CDX DAXN(1) DAXX(2) HF H WB_2 OAL
SGFFH 35-R/L-2 .083 .787 1.38 1.81 .031 1.260 .205 5.906
SGFFH 45-R/L-2 .083 .787 1.77 2.40 .031 1.260 .205 5.906
SGFFH 60-R-2 .083 .787 2.36 3.15 .031 1.260 .205 5.906
SGFFH 80-R/L-2 .083 .787 3.11 4.02 .031 1.260 .157 5.906
SGFFH 100-R/L-2 .083 .787 3.98 5.20 .000 1.260 .157 5.906
SGFFH 75-R/L-3 .118 .787 2.56 3.62 .039 1.260 .205 5.906
SGFFH 90-R/L-3 .118 .787 3.54 4.80 .008 1.260 .205 5.906
SGFFH 120-R/L-3 .118 .984 4.72 6.30 .000 1.260 .205 5.906
SGFFH 80-R/L-4 .157 1.181 3.15 6.10 .098 1.260 .205 5.906
SGFFH 150-R/L-4 .157 1.181 5.91 19.69 .098 1.260 .205 5.906
SGFFH 80-R/L-5 .197 1.260 3.15 6.38 .000 1.260 .205 5.906
SGFFH 150-R/L-5 .197 1.378 5.91 23.62 .000 1.260 .205 5.906
SGFFH 90-R/L-6 .236 1.260 3.54 5.91 .000 1.260 .315 5.906
SGFFH 150-R/L-6 .236 1.378 5.83 27.56 .000 1.260 .205 5.906
• Important: Apply R.H. insert on R.H. tool and L.H. insert on L.H. tool. Neutral insert only as indicated • H dimension links blades and blocks
(1) Minimum penetration diameter
(2) Maximum penetration diameter

For inserts, see pages: GFF-N (121)

For holders, see pages: SGTBF (136) • SGTBK (135) • SGTBU/SGTBN (133) • UBHCR/L (135)

Spare Parts

Designation
SGFFH 35-L-2 SET ESG 0.5
SGFFH 35-R-2 ESG 0.5
SGFFH 45-L-2 SET ESG 0.5
SGFFH 45-R-2 ESG 0.5
SGFFH 60-R-2 ESG 0.5
SGFFH 80-L-2 ESG 0.5
SGFFH 80-R-2 ESG 0.5
SGFFH 100-L-2 SET ESG 0.5
SGFFH 100-R-2 SET ESG 0.5
SGFFH 75-L-3 SET ESG 1
SGFFH 75-R-3 SET ESG 1
SGFFH 90-L-3 SET ESG 1
SGFFH 90-R-3 SET ESG 1
SGFFH 120-L-3 SET ESG 1
SGFFH 120-R-3 SET ESG 1
SGFFH 80-L-4 SET ESG 1
SGFFH 80-R-4 SET ESG 1
SGFFH 150-L-4 SET ESG 1
SGFFH 150-R-4 SET ESG 1
SGFFH 80-L-5 SET ESG 1
SGFFH 80-R-5 SET ESG 1
SGFFH 150-L-5 SET ESG 1
SGFFH 150-R-5 SET ESG 1
SGFFH 90-L-6 SET ESG 1
SGFFH 90-R-6 SET ESG 1
SGFFH 150-L-6 SET ESG 1
SGFFH 150-R-6 SET ESG 1

120 ISCAR
 FACE GROOVE-TURN
GFF-R/L
Face Grooving Inserts CDX
7°
R L
DAXN
CW
RE

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data
f face-groove

IC354

IC20
Designation CW RE CWTOL(1) RETOL(2) DAXN(3) DAXX(4) (mm/rev)
GFF 2R 2.10 0.20 0.10 0.050 25.0 36.0 • • 0.03-0.13
GFF 3L 3.00 0.30 0.10 0.050 30.0 55.0 • 0.03-0.15
GFF 3R 3.00 0.30 0.10 0.050 30.0 55.0 • • 0.03-0.15

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data
f face-groove

IC354

IC20
Designation CW RE CWTOL(1) RETOL(2) DAXN(3) DAXX(4) (IPR)
GFF 2R .083 .008 .0039 .0020 .98 1.42 • • .0012-.0051
GFF 3L .118 .012 .0039 .0020 1.18 2.17 • .0012-.0059
GFF 3R .118 .012 .0039 .0020 1.18 2.17 • • .0012-.0059
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Maximum axial grooving diameter

For tools, see pages: SGFFA (117) • SGFFR/L (115)

GFF-N
Face Grooving Inserts 7° N
CDX
RE
DAXN
CW

M E T R I C
Recommended
Dimensions Tough 1 Hard
Machining Data
f face-groove
IC354

IC20

Designation CW RE CWTOL(1) RETOL(2) DAXN(3) (mm/rev)

GFF 2N 2.10 0.20 0.10 0.050 35.0 • • 0.03-0.13
GFF 3N 3.00 0.30 0.10 0.050 54.0 • • 0.03-0.15
GFF 4N 4.00 0.25 0.10 0.050 35.0 • • 0.04-0.18
GFF 5N 5.00 0.25 0.10 0.050 40.0 • • 0.05-0.18
GFF 6N 6.00 0.25 0.10 0.050 44.0 • • 0.05-0.20

I N C H
Recommended
Dimensions Tough 1 Hard
Machining Data
f face-groove
IC354

IC20

Designation CW RE CWTOL(1) RETOL(2) DAXN(3) (IPR)

GFF 2N .083 .008 .0039 .0020 1.38 • • .0012-.0051
GFF 3N .118 .012 .0039 .0020 2.13 • • .0012-.0059
GFF 4N .157 .010 .0039 .0020 1.38 • • .0016-.0071
GFF 5N .197 .010 .0039 .0020 1.57 • • .0020-.0071
GFF 6N .236 .010 .0039 .0020 1.73 • • .0020-.0079
• Grooving depth is limited only by the tool being used
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter

For tools, see pages: SGFFA (117) • SGFFH (119) • SGFFR/L (115)

121
FACE GROOVE-TURN

PENTA-CUT
±0.04 34
CDX
PENTA 34F-R/L
Pentagonal Inserts for Face CDX DAXN DAXN
Grooving and Recessing
RE
DAXN

CW R L

M E T R I C
Recommended
Dimensions
Machining Data

f face-groove

IC908
Designation CW RE RETOL(1) CDX DAXN(2) (mm/rev)
PENTA 34F239-0.15-22R/L 2.39 0.15 0.020 5.00 22.0 • 0.08-0.12
PENTA 34F247-0.20-22R/L 2.47 0.20 0.020 5.00 22.0 • 0.08-0.12
PENTA 34F300-0.40-22R/L 3.00 0.40 0.020 5.00 22.0 • 0.08-0.15
PENTA 34F400-0.40-22R/L 4.00 0.40 0.020 5.00 22.0 • 0.08-0.15
• For cutting speed recommendations, see pages 162-164
(1) Corner radius tolerance (+/-)
(2) Minimum axial grooving diameter

For tools, see pages: • PCHBR/L (125) • PCHPR/L (127) • PCHR/L-34 (123) • PCHR/L-34-JHP (124)

±.0016 1.34
PENTA 34F-R/L CDX
Pentagonal Inserts for Face CDX DAXN DAXN
Grooving and Recessing
RE
DAXN

R L
CW

I N C H
Recommended
Dimensions
Machining Data

f face-groove
IC908

Designation CW RE RETOL(1) CDX DAXN(2) (IPR)

PENTA 34F239-0.15-22R/L .094 .0059 .0008 .197 .87 • .0031-.0047
PENTA 34F247-0.20-22R/L .097 .0079 .0008 .197 .87 • .0031-.0047
PENTA 34F300-0.40-22R/L .118 .0157 .0008 .197 .87 • .0031-.0059
PENTA 34F400-0.40-22R/L .157 .0157 .0008 .197 .87 • .0031-.0059
• For cutting speed recommendations, see pages 162-164
(1) Corner radius tolerance (+/-)
(2) Minimum axial grooving diameter

For tools, see pages: • PCHBR/L (125) • PCHPR/L (127) • PCHR/L-34 (123) • PCHR/L-34-JHP (124)

122 ISCAR
 FACE GROOVE-TURN
OAL
LH
PCHR/L-34
Grooving, Parting and HF H
Recessing Holders Carrying HBH CDX
Inserts with 5 Cutting Edges
WF B

CWN-CWX Right-hand shown

M E T R I C

Designation H HF B CWN(2) CWX(3) WF CDX(4) OAL LH HBH

PCHR/L 16-34 16.0 16.0 16.0 1.50 4.00 14.20 10.00 120.00 31.0 9.0 SR 16-212-01397
PCHR/L 20-34 20.0 20.0 20.0 1.50 4.00 18.20 10.00 120.00 31.0 6.0 SR 16-212-01397
PCHR/L 25-34 25.0 25.0 25.0 1.50 4.00 23.20 10.00 135.00 31.0 - SR 16-212-01397
PCHR/L 25-34-8 (1) 25.0 25.0 25.0 3.19 8.20 22.50 10.00 135.00 31.0 - SR PCHR-8-06642 T-15/5
PCHR/L 32-34 32.0 32.0 32.0 1.50 4.00 30.10 10.00 135.00 31.0 - SR 16-212-01397
(1) Used with special inserts only
(2) Minimum cutting width
(3) Maximum cutting width
(4) For specific information, refer to insert data

For inserts, see pages: PENTA 34F-R/L (122)

OAL
LH
PCHR/L-34
Grooving, Parting and HF H
Recessing Holders Carrying HBH CDX
Inserts with 5 Cutting Edges
WF B

CWN-CWX Right-hand shown

I N C H

Designation H HF B CWN(1) CWX(2) WF CDX(3) OAL LH HBH

PCHR/L 16-34 .630 .630 .630 .059 .157 .559 .394 4.724 1.220 .35 SR 16-212-01397
PCHR/L 19-34 .750 .750 .750 .059 .157 .680 .394 5.000 1.200 .24 SR 16-212-01397
PCHR/L 25.4-34 1.000 1.000 1.000 .059 .157 .930 .394 5.500 1.200 - SR 16-212-01397
(1) Minimum cutting width
(2) Maximum cutting width
(3) For specific information, refer to insert data

For inserts, see pages: PENTA 34F-R/L (122)

123
FACE GROOVE-TURN
H= 25 mm H= 16-20 mm
LH OAL
PCHR/L-34-JHP HBH
Grooving, Parting and H
Recessing Tools Carrying HF Lock
CNT HBL
PENTA Inserts with Channels CNT (typx3)
Bar Max
CDX
for High-Pressure Coolant WF B
CWN-CWX Right-hand shown

M E T R I C
Designation H HF B CWN(1) CWX(2) CDX(3) WF OAL LH HBH CNT Insert
PCHR/L 16-34-JHP 16.0 16.0 16.0 1.50 4.00 10.00 9.60 120.00 33.5 9.0 UNF 5/16-24 PENTA 34
PCHR/L 20-34-JHP 20.0 20.0 20.0 1.50 4.00 10.00 13.60 135.00 33.5 6.0 G1/8-28 PENTA 34
PCHR/L 25-34-JHP 25.0 25.0 25.0 1.50 4.00 10.00 18.60 135.00 33.5 - G1/8-28 PENTA 34
• For user guide and accessories, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) For specific information, refer to insert data

For inserts, see pages: PENTA 34F-R/L (122)

Spare Parts

Designation
PCHR/L 16-34-JHP SR 16-212-01397 SR 5/16UNF TL360 HW 5/32"
PCHR/L 20-34-JHP SR 16-212-01397 PLG G1/8 TL360 HW 5.0
PCHR/L 25-34-JHP SR 16-212-01397

H= 1.00” H= .575-.750”
OAL
LH
PCHR/L-34-JHP HBH
Grooving, Parting and H
Recessing Tools Carrying HF Lock
CNT HBL
PENTA Inserts with Channels CNT (typx3) PSI Max

for High-Pressure Coolant WF B

CWN-CWX

I N C H
Designation H HF B CWN(1) CWX(2) CDX(3) WF OAL LH HBH CNT Insert
PCHR/L 16-34-JHP .630 .630 .630 .059 .157 .394 .378 4.724 1.319 .35 UNF 5/16-24 PENTA 34
PCHR/L 19-34-JHP .750 .750 .750 .059 .157 .394 .490 5.320 1.300 .24 G1/8-28 PENTA 34
PCHL 25.4-34-JHP 1.000 1.000 1.000 .059 .157 .394 .730 5.315 1.319 - G1/8-28 PENTA 34
PCHR 25.4-34-JHP 1.000 1.000 1.000 .059 .157 .394 .730 5.320 1.300 - G1/8-28 PENTA 34
• For user guide and accessories, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) For specific information, refer to insert data

For inserts, see pages: PENTA 34F-R/L (122)

Spare Parts

Designation
PCHR/L 16-34-JHP SR 16-212-01397 SR 5/16UNF TL360 HW 5/32"
PCHR/L 19-34-JHP SR 16-212-01397 PLG G1/8 TL360 HW 5.0
PCHR/L 25.4-34-JHP SR 16-212-01397

124 ISCAR
 FACE GROOVE-TURN
CWN-CWX

PCHBR/L
Double-Ended Parting
and Grooving Blades for H HF
PENTACUT Inserts
WB_2 WF OAL
Left-hand shown

M E T R I C

Designation H CWN(2) CWX(3) HF WF(4) OAL WB_2 Insert

PCHBL 26-24R 26.0 0.50 6.20 21.4 7.00 110.00 8.5 PENTA 24 SR 16-212-01397L
PCHBR 26-24L 26.0 0.50 6.20 21.4 7.00 110.00 8.5 PENTA 24 SR 16-212-01397
PCHBR 26-24R 26.0 0.50 6.20 21.4 1.50 110.00 8.5 PENTA 24 SR 16-212-01397L
PCHBL 32-24R 32.0 0.50 6.20 24.8 7.00 110.00 8.5 PENTA 24 SR 16-212-01397L
PCHBR 32-24L 32.0 0.50 6.20 24.8 7.00 110.00 8.5 PENTA 24 SR 16-212-01397
PCHBL 26-34R (1) 26.0 1.50 4.00 21.4 7.15 110.00 8.5 PENTA 34 SR 16-212-01397
PCHBR 26-34L (1) 26.0 1.50 4.00 21.4 7.15 110.00 8.5 PENTA 34 SR 16-212-01397
PCHBR 26-34R (1) 26.0 1.50 4.00 21.4 1.35 110.00 8.5 PENTA 34
PCHBL 32-34R 32.0 1.50 4.00 24.8 7.15 110.00 8.5 PENTA 34 SR 16-212-01397
PCHBR 32-34L 32.0 1.50 4.00 24.8 7.15 110.00 8.5 PENTA 34 SR 16-212-01397
• For insert/blade orientation, see the following drawings
(1) Single pocket blade
(2) Minimum cutting width
(3) Maximum cutting width
(4) To the center of inserts up to 4.15 mm width

For inserts, see pages: PENTA 34F-R/L (122)

PCHBL 26-24L PCHBL 26-24R

PCHBL 26-24R Shown

Lock

Left-hand blade

Lock

PCHBR 26-24L PCHBR 26-24R

Pocket location on
Right-hand blade the blade

125
FACE GROOVE-TURN
CWN-CWX

PCHBR/L
Double-Ended Parting
and Grooving Blades for H HF
PENTACUT Inserts
WB_2 WF OAL
Left-hand shown

I N C H

Designation H CWN(2) CWX(3) HF WF(4) OAL WB_2 Insert

PCHBL 26-24R 1.024 .020 .244 .843 .276 4.331 .335 PENTA 24 SR 16-212-01397L
PCHBR 26-24L 1.024 .020 .244 .843 .276 4.331 .335 PENTA 24 SR 16-212-01397
PCHBR 26-24R 1.024 .020 .244 .843 .059 4.331 .335 PENTA 24 SR 16-212-01397L
PCHBL 32-24R 1.260 .020 .244 .976 .276 4.331 .335 PENTA 24 SR 16-212-01397L
PCHBR 32-24L 1.260 .020 .244 .976 .276 4.331 .335 PENTA 24 SR 16-212-01397
PCHBL 26-34R (1) 1.024 .059 .157 .843 .281 4.331 .335 PENTA 34 SR 16-212-01397
PCHBR 26-34L (1) 1.024 .059 .157 .843 .281 4.331 .335 PENTA 34 SR 16-212-01397
PCHBR 26-34R (1) 1.024 .059 .157 .843 .053 4.331 .335 PENTA 34
PCHBL 32-34R 1.260 .059 .157 .976 .281 4.331 .335 PENTA 34 SR 16-212-01397
PCHBR 32-34L 1.260 .059 .157 .976 .281 4.331 .335 PENTA 34 SR 16-212-01397
• For insert/blade orientation, see the following drawings
(1) Single pocket blade
(2) Minimum cutting width
(3) Maximum cutting width
(4) To the center of inserts up to .163" width

For inserts, see pages: PENTA 34F-R/L (122)

PCHBL 26-24L PCHBL 26-24R

PCHBL 26-24R Shown

Lock

Left-hand blade

Lock

PCHBR 26-24L PCHBR 26-24R

Pocket location on
Right-hand blade the blade

126 ISCAR
 FACE GROOVE-TURN
LH
CDX
PCHPR/L H
HF
Perpendicular Holders
HBH
Carrying Inserts with 5 Cutting OAL LF
Edges for Facing, Grooving,
B Lock
Parting and Recessing
CWN-CWX
WF Right-hand shown

M E T R I C
Designation H B CWN(1) CWX(2) CDX(3) HF WF LF OAL LH HBH
PCHPR/L 16-24 16.0 16.0 0.50 3.20 (4) 6.50 16.0 1.50 (5) 23.5 120.00 11.5 -
PCHPR/L 20-24 20.0 20.0 0.50 3.20 (4) 6.50 20.0 1.50 (5) 28.0 120.00 11.5 -
PCHPR/L 25-24 25.0 25.0 0.50 3.20 (4) 6.50 25.0 1.50 (5) 33.0 135.00 11.5 -
PCHPR/L 20-34 20.0 20.0 1.40 4.00 10.00 20.0 1.90 34.0 120.00 15.0 6.0
PCHPR/L 25-34 25.0 25.0 1.40 4.00 10.00 25.0 1.90 34.0 135.00 15.0 -
(1) Minimum cutting width
(2) Maximum cutting width
(3) For specific information, refer to insert data
(4) Up to 6.2 mm width may be ordered on request
(5) Valid for inserts with CW<3.2 mm

For inserts, see pages: PENTA 34F-R/L (122)

Spare Parts

Designation
PCHPL 16-24 SR 16-212-01397 T-20/5
PCHPR 16-24 SR 16-212-01397L T-20/5
PCHPL 20-24 SR 16-212-01397 T-20/5
PCHPR 20-24 SR 16-212-01397L T-20/5
PCHPL 25-24 SR 16-212-01397 T-20/5
PCHPR 25-24 SR 16-212-01397L T-20/5
PCHPR/L 20-34 SR 16-212-01397 T-20/5
PCHPR/L 25-34 SR 16-212-01397 T-20/5

127
FACE GROOVE-TURN
LH
CDX
PCHPR/L H
HF
Perpendicular Holders
HBH
Carrying Inserts with 5 Cutting OAL LF
Edges for Facing, Grooving,
B Lock
Parting and Recessing
CWN-CWX
WF Right-hand shown

I N C H
Designation H B CWN(1) CWX(2) CDX(3) HF WF LF OAL LH HBH
PCHPR/L 16-24 .630 .630 .020 .126 (4) .256 .630 .059 (5) .93 4.724 .453 -
PCHPR/L 19-24 .750 .750 .020 .126 (4) .256 .750 .060 (5) 1.10 5.000 .450 -
PCHPR/L 25.4-24 1.000 1.000 .020 .126 (4) .256 1.000 .060 (5) 1.30 5.500 .450 -
PCHPR/L 19-34 .750 .750 .055 .157 .394 .750 .070 1.30 5.000 .590 .24
PCHPR/L 25.4-34 1.000 1.000 .055 .157 .394 1.000 .070 1.30 5.500 .590 -
(1) Minimum cutting width
(2) Maximum cutting width
(3) For specific information, refer to insert data
(4) Up to .244" width may be ordered on request.
(5) Valid for inserts with W<.126"

For inserts, see pages: PENTA 34F-R/L (122)

Spare Parts

Designation
PCHPL 16-24 SR 16-212-01397 T-20/5
PCHPR 16-24 SR 16-212-01397L T-20/5
PCHPL 19-24 SR 16-212-01397 T-20/5
PCHPR 19-24 SR 16-212-01397L T-20/5
PCHPL 25.4-24 SR 16-212-01397 T-20/5
PCHPR 25.4-24 SR 16-212-01397L T-20/5
PCHPR/L 19-34 SR 16-212-01397 T-20/5
PCHPR/L 25.4-34 SR 16-212-01397 T-20/5

128 ISCAR
 FACE GROOVE-TURN
±0.04 34
PENTA 34F-RS/LS CDX CDX
Pentagonal Inserts for Face
Grooving and Recessing Along DAXN
DAXN
Shafts up to 5 mm Depth of Cut
at a Minimum of 22 mm Diameter CW RE

M E T R I C
Dimensions Recommended Machining Data

f face-groove

IC908
Designation CW RE CDX DAXN(1) (mm/rev)
PENTA 34F239-0.15-22R/LS 2.39 0.15 5.00 22.0 • 0.08-0.12
PENTA 34F247-0.20-22R/LS 2.47 0.20 5.00 22.0 • 0.08-0.12
PENTA 34F300-0.40-22R/LS 3.00 0.40 5.00 22.0 • 0.08-0.15
PENTA 34F400-0.40-22R/LS 4.00 0.40 5.00 22.0 • 0.08-0.15
• For cutting speed recommendations, see pages 162-164
(1) Minimum axial grooving diameter

For tools, see pages: PCHPRS/LS (130)

±.0016
1.33
PENTA 34F-RS/LS CDX CDX
Pentagonal Inserts for Face
Grooving and Recessing Along DAXN
DAXN
Shafts up to .197" Depth of Cut
at a Minimum of .866" Diameter CW RE

I N C H
Dimensions Recommended Machining Data

f face-groove
IC908

Designation CW RE CDX DAXN(1) (IPR)

PENTA 34F239-0.15-22R/LS .094 .0059 .197 .87 • .0031-.0047
PENTA 34F247-0.20-22R/LS .097 .0079 .197 .87 • .0031-.0047
PENTA 34F300-0.40-22R/LS .118 .0157 .197 .87 • .0031-.0059
PENTA 34F400-0.40-22R/LS .157 .0157 .197 .87 • .0031-.0059
• For cutting speed recommendations, see pages 162-164
(1) Minimum axial grooving diameter

For tools, see pages: PCHPRS/LS (130)

129
FACE GROOVE-TURN
15 6
CDX
PCHPRS/LS CDX H
Perpendicular Shank HF
HBH
Tools Carrying Pentagonal DAXN OAL 33.8
Inserts for Machining Next
B
to Long Central Shafts
14.04
3° CWN-CWX Right-hand shown

M E T R I C

Designation H B CWN(1) CWX(2) OAL HBH CDX(3) HF

PCHPR/LS 20-34 20.0 20.0 2.39 4.00 120.00 6.0 5.00 20.0 SR 16-212-01397RS T-20/5
PCHPR/LS 25-34 25.0 25.0 2.39 4.00 135.00 - 5.00 25.0 SR 16-212-01397RS T-20/5
(1) Minimum cutting width
(2) Maximum cutting width
(3) Insert limit

For inserts, see pages: PENTA 34F-RS/LS (129)

.59 .236
CDX
PCHPRS/LS CDX H
Perpendicular Shank H
HBH
Tools Carrying Pentagonal DAXN OAL 1.33
Inserts for Machining Next
B
to Long Central Shafts
.55
3° CWN-CWX Right-hand shown

I N C H

Designation H B CWN(1) CWX(2) OAL HBH CDX(3) DAXN(4)

PCHPR/LS 19-34 .750 .750 .094 .157 5.000 .24 .197 .87 SR 16-212-01397RS T-20/5
PCHPR/LS 25.4-34 1.000 1.000 .094 .157 5.500 - .197 .87 SR 16-212-01397RS T-20/5
(1) Minimum cutting width
(2) Maximum cutting width
(3) Insert limit
(4) Minimum axial grooving diameter

For inserts, see pages: PENTA 34F-RS/LS (129)

130 ISCAR
 HOLDERS

131
FACE GROOVE-TURN
FACE GROOVE-TURN

TOOL BLOCKS
JETCUT Assembly

C Insert GF The coolant supply tube can be used

with the following options:
D Blade SGFHK-
E Cap SGC 340 supplied with a blade; • DGTR...C integral tool
to be used with Option 1 only. • DGFH-C blades used on regular blocks
by connecting directly to the blade
F Tool block SGTBUC-
• SGTBU-C blocks with coolant passages
G Elbow-style connector unit supplied
and connecting ports
with each tool block
H SGCU-344 H 3/16” copper Tube 343 (length 250 mm) The Right Connection for Your Application
J Standard current tool blocks SGTBN, SGTBU, SGTBF Option 1:
K Coolant connection unit SGCU-341 Coolant supplied directly to the blade.
M Integral shank holder SGTFR/LK-

Option 1:
Coolant supplied through the tool block.

D F

H
C
SGCU 341 Coolant connection unit
E
G Connectors:
CGM 343 (G1/8 external thread)
CGF 343 (G1/8 internal thread)
Option 2: CF 343 (NPT1/8 internal thread)
Coolant supplied directly to the blade.
Option 2:
Coolant supplied through the tool block.
D J

Option 3: SGCU 344 Elbow connector

Coolant supplied directly to the integral shank tool.
TUBE 343
3/16” copper tube (length 250 mm)
(G1/8 external thread) (G1/8 internal thread)
(NPT1/8 external thread) (NPT1/8 internal thread)
M
Option 3:
Coolant supplied directly to the tool.
K
C

SGCU 341 Coolant connection unit

Connectors:
CGM 343 (G1/8 external thread)
CGF 343 (G1/8 internal thread)
CF 343 (NPT1/8 internal thread)

132 ISCAR
 FACE GROOVE-TURN
SGTBU- --G
OAH H WTHPRM HTPRM
SGTBU/SGTBN
Blocks for Various Parting OAL B
HBH OAW
and Grooving Blades
SGTBU- C-
SGTBN

Coolant connection

M E T R I C
Designation H B HTPRM OAW OAH HBH WTHPRM OAL
SGTBN 16-2 16.0 16.0 19.0 26.00 30.0 4.0 2.00 76.00
SGTBU 16-5G 16.0 17.0 26.0 34.00 43.0 13.0 4.10 86.00
SGTBU 20-5G 20.0 21.0 26.0 38.00 43.0 9.0 4.10 86.00
SGTBU 20-6G 20.0 19.1 32.0 38.20 50.0 12.9 5.30 100.00
SGTBU 25-5G 25.0 26.1 26.0 43.10 45.0 5.0 4.10 110.00
SGTBU 25-6G 25.0 23.0 32.0 42.20 50.0 7.8 5.30 110.00
SGTBU 25-8M 25.0 23.0 45.0 42.20 70.0 27.0 5.30 110.00
SGTBU 25C-6 (1) 25.0 23.0 32.0 42.20 50.0 7.8 5.30 110.00
SGTBU 32-25-6G 32.0 25.1 32.0 44.15 54.0 4.8 5.30 110.00
SGTBU 32-6G 32.0 29.1 32.0 28.20 54.0 4.8 5.30 110.00
SGTBU 32-8M 32.0 29.0 45.0 48.20 70.0 20.0 5.30 110.00
SGTBU 32C-14 (1) 32.0 28.0 52.6 63.00 99.8 41.7 12.60 140.00
SGTBU 40-6G 40.0 - 32.0 60.00 57.0 - 5.30 114.00
SGTBU 40-9 40.0 41.0 52.6 66.00 81.0 22.0 8.00 130.00
SGTBU 40C-14 (1) 40.0 28.0 52.6 63.00 99.8 33.8 12.60 140.00
SGTBU 50-9 50.0 41.0 52.6 66.00 83.0 14.0 8.00 135.00
SGTBU 50C-14 (1) 50.0 28.0 52.6 63.00 99.8 23.8 12.60 140.00
SGTBU 100-9-12 (2) 50.0 49.0 100.0 106.00 155.0 73.5 15.00 225.00
SGTBU 150-9-12 (2) 50.0 49.0 150.0 106.00 209.0 127.5 15.00 306.00
• Choose blade by HTPRM and WTHPRM dimensions
(1) Elbow-style connector unit supplied with each JET-CUT tool block
(2) See more detailed information below

For tools, see pages: • CGFG 51-P8 (88) • HFFA (38) • HFFH (37) • HFFR/L-T (51) • PCHBR/L (125) • SGFFA (117) • SGFFH (119) • TNFFA-IQ (110) • TNFFH-IQ (109)

SGTBU 100/150-9-12

H
HTPRM OAH

B HBH

OAW OAL

Spare Parts

Designation
SGTBN 16-2 SR M5X20DIN912 HW 4.0
SGTBU 16-5G BKU 86 SR M6X16 DIN912 HW 5.0
SGTBU 20-5G BKU 86 SR M6X16 DIN912 HW 5.0
SGTBU 20-6G BKU 100 SR M6X16 DIN912 HW 5.0
SGTBU 25-5G BKU 105 SR M6X16 DIN912 HW 5.0
SGTBU 25-6G BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 25-8M BKU 110 SR M6X16 DIN912 SR M6X30 DIN912 HW 5.0
SGTBU 25C-6 BKU 110 SR M6X16 DIN912 HW 5.0 SGCU-344* CF 343* CGF 343* CGM 343*
SGTBU 32-25-6G BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 32-6G BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 32-8M BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 32C-14 BKU 32-14 SR M10X30 DIN912 HW 8.0 JHP ELBOW 90-G1/8-7/16UNF OR 34X2.5N
SGTBU 40-6G BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 40-9 BK 509 SR M8X25DIN912 HW 6.0
SGTBU 40C-14 BKU 32-14 SR M10X30 DIN912 HW 8.0 JHP ELBOW 90-G1/8-7/16UNF OR 34X2.5N
SGTBU 50-9 BK 509 SR M8X25DIN912 HW 6.0
SGTBU 50C-14 BKU 32-14 SR M10X30 DIN912 HW 8.0 JHP ELBOW 90-G1/8-7/16UNF OR 34X2.5N
SGTBU 100-9-12 SR M10X25 DIN912 HW 8.0
SGTBU 150-9-12 SR M10X25 DIN912 HW 8.0
* Optional, should be ordered separately

133
FACE GROOVE-TURN
SGTBU- --G
OAH H WTHPRM HTPRM
SGTBU/SGTBN
Blocks for Various Parting OAL B
HBH OAW
and Grooving Blades
SGTBU- C-
SGTBN

Coolant connection

I N C H
Designation H B HTPRM OAW OAH HBH WTHPRM OAL
SGTBN 16-2 .630 .630 .748 1.024 1.18 .16 .079 2.992
SGTBU 16-5G .630 .669 1.024 1.339 1.69 .51 .161 3.386
SGTBU 19-5G .750 .790 1.024 1.450 1.70 .39 .160 3.400
SGTBU 19-6G .750 .790 1.260 1.500 1.94 .55 .210 3.950
SGTBU 25.4-5G 1.000 1.030 1.024 1.700 1.75 .20 .160 4.330
SGTBU 25.4-6G 1.000 1.028 1.260 1.750 1.95 .30 .210 4.330
SGTBU 25.4-8M 1.000 .906 1.772 1.654 2.76 1.06 .209 4.331
SGTBU 25.4C-6 (1) 1.000 1.028 1.260 1.744 1.94 .30 .210 4.330
SGTBU 31.8-6G 1.250 1.140 1.260 1.900 2.10 .20 .210 4.330
SGTBU 31.8C-14 1.250 1.140 2.071 2.477 3.93 1.65 .498 5.512
SGTBU 38.1-6G 1.500 1.650 1.260 2.283 2.15 - .210 4.500
SGTBU 38.1-9 1.500 1.540 2.071 2.520 3.20 .94 .310 5.120
SGTBU 38.1C-14 (1) 1.500 1.102 2.071 2.476 3.93 1.41 .498 5.512
SGTBU 100-9-12 (2) 1.968 1.929 3.937 4.173 6.10 2.89 .591 8.858
SGTBU 150-9-12 (2) 1.968 1.929 5.906 4.173 8.23 5.02 .591 12.047
• Choose blade by HTPRM and WTHPRM dimensions
(1) Elbow-style connector unit supplied with each JET-CUT tool block
(2) See more detailed information below

For tools, see pages: • CGFG 51-P8 (88) • HFFA (38) • HFFH (37) • HFFR/L-T (51) • PCHBR/L (125) • SGFFA (117) • SGFFH (119) • TNFFA-IQ (110) • TNFFH-IQ (109)

Spare Parts

Designation
SGTBN 16-2 SR M5X20DIN912 HW 4.0
SGTBU 16-5G BKU 86 SR M6X16 DIN912 HW 5.0
SGTBU 19-5G BKU 86 SR M6X16 DIN912 HW 5.0
SGTBU 19-6G BKU 100 SR M6X16 DIN912 HW 5.0
SGTBU 25.4-5G BKU 105 SR M6X16 DIN912 HW 5.0
SGTBU 25.4-6G BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 25.4-8M BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 25.4C-6 BKU 110 SR M6X16 DIN912 SR M6X25 DIN912 HW 5.0 SGCU-344* CF 343* CGF 343* CGM 343*
SGTBU 31.8-6G BKU 110 SR M6X16 DIN912 HW 5.0
SGTBU 31.8C-14 BKU 32-14 SR M10X30 DIN912 HW 8.0 JHP ELBOW 90-G1/8-7/16UNF OR 34X2.5N
SGTBU 38.1-6G BKU 110 SR M6X25 DIN912 HW 5.0
SGTBU 38.1-9 BK 509 SR M8X25DIN912 HW 6.0
SGTBU 38.1C-14 BKU 32-14 SR M10X30 DIN912 HW 8.0 JHP ELBOW 90-G1/8-7/16UNF OR 34X2.5N
SGTBU 100-9-12 SR M10X25 DIN912 HW 8.0
SGTBU 150-9-12 SR M10X25 DIN912 HW 8.0

134 ISCAR
 FACE GROOVE-TURN
SGTBK
Blocks for Heavy Duty Parting
and Grooving Blades OAH H HTPRM

HBH B WTHPRM
OAL
OAW

M E T R I C

Designation H B WTHPRM HTPRM OAW OAH HBH OAL

SGTBK 32-9 32.0 28.0 8.50 32.0 48.00 62.0 3.0 120.00 BK 32-9 WEDG SR M6X16 DIN912 HW 5.0
SGTBK 38-9 38.0 35.0 8.50 52.6 60.00 90.0 25.0 135.00 BK 40-9 SR M6X20 DIN912 HW 5.0
SGTBK 40-9 40.0 35.0 8.50 52.6 60.00 90.0 23.0 135.00 BK 40-9 SR M6X20 DIN912 HW 5.0
SGTBK 50-9 50.0 40.0 8.50 52.6 65.00 90.0 15.0 135.00 BK 40-9 SR M6X20 DIN912 HW 5.0

I N C H

Designation H B WTHPRM HTPRM OAW OAH HBH OAL

SGTBK 32-9 1.260 1.102 .335 1.260 1.890 2.44 .12 4.724 BK 32-9 WEDG SR M6X16 DIN912 HW 5.0
SGTBK 38-9 1.496 1.378 .335 2.071 2.362 3.54 .98 5.315 BK 40-9 SR M6X20 DIN912 HW 5.0
SGTBK 40-9 1.575 1.378 .335 2.071 2.362 3.54 .91 5.315 BK 40-9 SR M6X20 DIN912 HW 5.0
SGTBK 50-9 1.968 1.575 .335 2.071 2.559 3.54 .59 5.315 BK 40-9 SR M6X20 DIN912 HW 5.0
• Choose blade by HTPRM dimension
For tools, see pages: • CGFG 51-P8 (88) • HFFH (37) • PCHBR/L (125) • SGFFH (119) • TNFFH-IQ (109)

UBHCR/L
Holders for Grooving, Turning
OAH H HTPRM
and Parting Blades
OAL B
OAW

Right-hand shown

M E T R I C

Designation H HTPRM B OAH OAW OAL

UBHCR/L 20-26 20.0 26.0 20.0 42.0 35.60 100.00 BKU 176 307 SR M6X16 DIN912 HW 5.0 SPRING PLUNGER M6X14X3.5
UBHCR/L 25-32 25.0 32.0 25.0 46.0 40.00 130.00 BKU 176 307 SR M6X16 DIN912 HW 5.0 SPRING PLUNGER M6X14X3.5
UBHCR/L 32-32 32.0 32.0 32.0 46.0 47.00 130.00 BKU 176 307 SR M6X16 DIN912 HW 5.0 SPRING PLUNGER M6X14X3.5

I N C H

Designation H HTPRM B OAH OAW OAL

UBHCR/L 19-26 .750 1.024 .750 1.42 1.400 3.937 BKU 176 307 SR M6X16 DIN912 HW 5.0 SPRING PLUNGER M6X14X3.5
UBHCR/L 25.4-32 1.000 1.260 1.000 1.81 1.600 5.118 BKU 176 307 SR M6X16 DIN912 HW 5.0 SPRING PLUNGER M6X14X3.5
• Choose blade by HTPRM dimension
For tools, see page: • HFFA (38) • HFFH (37) • HFFR/L-T (51) • SGFFA (117) • SGFFH (119) • TNFFA-IQ (110) • TNFFH-IQ (109)

135
FACE GROOVE-TURN
h2 Ref.(a)

SGTBF HTPRM H OAH

WTHPRM
Perpendicular Blocks for
Parting and Grooving Blades
OAW B
LSCMS
OAL

M E T R I C

Designation H B HTPRM OAL LSCMS OAW OAH WTHPRM

SGTBF 25-A 25.0 25.0 32.0 102.00 80.00 48.00 48.0 5.50 SR M6X40 DIN912 HW 5.0
SGTBF 32-A 32.0 32.0 32.0 116.00 100.00 48.00 48.0 5.50 SR M6X40 DIN912 HW 5.0

I N C H

Designation H B HTPRM OAL LSCMS OAW OAH WTHPRM

SGTBF 25.4-A 1.000 1.000 1.260 5.000 4.380 1.750 1.90 .217 SR M6X40 DIN912 HW 5.0
SGTBF 31.7-A 1.250 1.250 1.260 5.000 4.390 1.750 1.90 .217 SR M6X40 DIN912 HW 5.0
• (a) h2 Ref. as defined for SELF-GRIP face grooving blades • Choose blade by HTPRM dimension
For tools, see pages: • HFFA (38) • HFFH (37) • HFFR/L-T (51) • SGFFA (117) • SGFFH (119) • TNFFA-IQ (110) • TNFFH-IQ (109)

136 ISCAR
 FACE GROOVE-TURN
CAMFIX
CAMFIX (ISO 266231)

Quick Change tools are expensive compared to standard shank

tools. ISCAR offers economical solutions by using adapters, blades
or regular tools and boring bars on the Quick Change adaptations.

C
CAMFIX ISO 26623-1
l8
Toolholder Standard l7
A
2e
d4

d2 d1 Dm

d5 b2
l1
l11 A
l6 A-A C-C
l2 l3
C

CAMFIX b2 d1 ±0.1 d2 d4 d5 ±0.1 Dm e l1 l2 ±0.1 l3 min l6 ±0.15 l7 ±0.15 l8 min l11 ±0.1
C3 28,3 32 15 M12x1.5 3,6 22 0,7 2,5 19 15 6 13 25 8
C4 35,3 40 18 M14x1.5 4,6 28 0,9 2,5 24 20 8 15 30 11,5
C5 44,4 50 21 M16x1.5 6,1 35 1,12 3 30 20 10 20 37 14
C6 55,8 63 28 M20x2 8,1 44 1,4 3 38 22 12 27 47 15,5
C8 71,1 80 32 M20x2 9,1 55 2 3 48 30 12 28 48 25
C8X 88,7 100 32 M20x2 9,1 55 2 3 48 32 16 28 48 25
C10 88,3 100 43 M24x2 12 72 2,8 3 60 36 16 40 70 26,5

CAMFIX - ISO 26623-1 Standard Quick Change Shanks

Features
• Symmetrical design: Due to the symmetrical
Hole for
design, the torque load is distributed on the Data Chip
polygon, providing a self-centering effect. Coolant
• Rigidity: The CAMFIX clamping mechanism technological hole
is extremely rigid against bending forces. Magazine and spindle V-groove for ATC
• Accuracy: The taper and face contact ensure positioning groove (Automatic Tool
high repeatability within 2 microns when Change) arm
operated with an automatic tool changer.

137
FACE GROOVE-TURN

C#-TBK-R/L LPR
Blocks with CAMFIX
OHX
Exchangeable Shanks for DCONMS
WF Right-hand shown
Parting and Grooving Blades
• OHX = See specific blade dimensions

M E T R I C

Designation DCONMS WF LPR H CP(1) CDI(2)

C6 TBK-32R/L 63.00 32.0 138.00 32.0 100 1 BK 32-9 WEDG SR M6X16 DIN912 HW 5.0 EZ 125 SR M8X6 DIN913
C8 TBK-52R 80.00 40.5 161.00 52.0 100 1 BK 40-9 SR M6X16 DIN912 HW 5.0 EZ 125 SR M8X6 DIN913

I N C H

Designation DCONMS WF LPR H CP(1) CDI(2)

C6 TBK-32R/L 2.480 1.260 5.433 1.260 1450 1 BK 32-9 WEDG SR M6X16 DIN912 HW 5.0 EZ 125 SR M8X6 DIN913
C8 TBK-52R 3.150 1.594 6.339 2.047 1450 1 BK 40-9 SR M6X16 DIN912 HW 5.0 EZ 125 SR M8X6 DIN913
Coolant pressure (Bar)
(1)

1 - Hole for data chip, 0 - Without hole for data chip

(2)

For tools, see pages: • HFFH (37) • PCHBR/L (125) • TNFFH-IQ (109)

DCONMS
45° 45º
LB
LPR
CDX
C#-MAHDR-45
Holders with CAMFIX BD
Exchangeable Shanks for L1
Parting, Grooving, Turning 45°LF Right-hand shown
• CDX = See specific adapter dimensions
and Facing Adapters
M E T R I C
Designation DCONMS LPR L1 LB LF BD CP(1) CDI(2)
C6 MAHDR-45 63.00 130.00 91.9 105.78 89.0 75.00 100 1
C8 MAHDR-45 80.00 130.00 91.9 - 89.0 80.00 100 1

I N C H
Designation DCONMS LPR L1 LB LF BD CP(1) CDI(2)
C6 MAHDR-45 2.480 5.118 3.618 4.165 3.504 2.953 1450 1
C8 MAHDR-45 3.150 5.118 3.618 - 3.504 3.150 1450 1
• For mill-turn machines
(1) Coolant pressure (Bar)
(2) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
C6 MAHDR-45 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20DIN7984 HW 4.0 SR M6X6DIN551 14H/22H(c) SR M5X4 DIN913 EZ 83
C8 MAHDR-45 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) SR M5X6 DIN913 EZ 83
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole

138 ISCAR
 FACE GROOVE-TURN
DCONMS

C#-MAHDOR LPR
Holders with CAMFIX CDX
Exchangeable Shanks for
Parting, Grooving, Turning WF
Right-hand shown • CDX = See specific adapter dimensions
and Facing Adapters
M E T R I C

Designation DCONMS WF LPR CDI(1)

C6 MAHDOR 63.00 29.0 130.00 1 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125

I N C H

Designation DCONMS WF LPR CDI(1)

C6 MAHDOR 2.480 1.142 5.118 1 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125
(1) 1 - Hole for data chip, 0 - Without hole for data chip
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

C#-MAHD LPR
Holders with CAMFIX WF
Exchangeable Shanks for DCONMS Right-hand shown
Parting, Grooving, Turning • CDX = See specific
CDX adapter dimensions
and Facing Adapters
M E T R I C
Designation DCONMS LPR WF CP(1) CDI(2)
C3 MAHD 32.00 50.00 18.5 100 0
C4 MAHD 40.00 46.50 22.1 100 1
C5 MAHD 50.00 47.00 23.0 100 1
C6 MAHD 63.00 50.00 29.0 100 1
C8 MAHD 80.00 60.00 37.5 100 1

I N C H
Designation DCONMS LPR WF CP(1) CDI(2)
C3 MAHD 1.260 1.968 .728 1450 0
C4 MAHD 1.575 1.831 .870 1450 1
C5 MAHD 1.968 1.850 .906 1450 1
C6 MAHD 2.480 1.968 1.142 1450 1
C8 MAHD 3.150 2.362 1.476 1450 1
Coolant pressure (Bar)
(1)

1 - Hole for data chip, 0 - Without hole for data chip

(2)

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
C#-MAHD SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125 EZA 125 SR 76-1022
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole

139
FACE GROOVE-TURN

Bar Max

C#-MAHD-JHP LPR
Holders with CAMFIX Right-hand shown
WF • CDX = See specific adapter
Exchangeable Shanks and High DCONMS
CDX dimensions
Pressure Coolant Channels for • WF=WF(shank)+WF(adapter)
MODULAR-GRIP Adapters
M E T R I C

Designation DCONMS LPR WF CDI(1)

C3 MAHD-JHP 32.00 45.00 18.5 0 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C4 MAHD-JHP 40.00 46.50 21.0 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C5 MAHD-JHP 50.00 47.00 26.0 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C6 MAHD-JHP 63.00 50.00 32.5 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK

I N C H

Designation DCONMS LPR WF CDI(1)

C3 MAHD-JHP 1.260 1.772 .728 0 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C4 MAHD-JHP 1.575 1.831 .827 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C5 MAHD-JHP 1.968 1.850 1.024 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C6 MAHD-JHP 2.480 1.968 1.280 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
• For user guide and accessories, see pages 137, 161-173
(1) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48)

SR M6X20-XT
(Key: HW 5.0)
OR 5X1N
SR M4X8ISO14580 (Key: T-20/5)

SR M6X12DIN6912 (Key: HW 5.0)

SR M5-04451(Key: T-20/5)

140 ISCAR
 FACE GROOVE-TURN
LPR

DCONMS
C#-MAHPD
Perpendicular Holders with WF
CAMFIX Exchangeable Shanks
CDX
Carrying Adapters for Parting,
CDX = See specific adapter dimensions
Grooving, Turning and Facing
M E T R I C
Designation DCONMS LPR WF CP(1) CDI(2)
C4 MAHPD 40.00 46.00 25.00 100 1
C5 MAHPD 50.00 46.00 26.00 100 1
C6 MAHPD 63.00 47.00 33.00 100 1
C8 MAHPD 80.00 56.00 42.00 100 1

I N C H
Designation DCONMS LPR WF CP(1) CDI(2)
C4 MAHPD 1.575 1.811 .984 1450 1
C5 MAHPD 1.968 1.811 1.024 1450 1
C6 MAHPD 2.480 1.850 1.299 1450 1
C8 MAHPD 3.150 2.205 1.654 1450 1
Coolant pressure (Bar)
(1)

1 - Hole for data chip, 0 - Without hole for data chip

(2)

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
C#-MAHPD SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125 SR 76-1022 EZA-21414
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole

LF

Bar Max

DCONMS
C#-MAHPD-JHP
Perpendicular Holders with WF
CAMFIX Exchangeable Shanks
CDX
for Parting, Grooving, Turning
CDX= See specific adapter dimensions
and Facing Adapters
M E T R I C

Designation DCONMS LF WF CDI(1)

C3 MAHPD-JHP 32.00 40.00 26.00 0 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C4 MAHPD-JHP 40.00 46.00 26.00 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C5 MAHPD-JHP 50.00 46.00 26.00 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C6 MAHPD-JHP 63.00 46.00 33.00 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK

I N C H

Designation DCONMS LF WF CDI(1)

C3 MAHPD-JHP 1.260 1.575 1.024 0 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C4 MAHPD-JHP 1.575 1.811 1.024 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C5 MAHPD-JHP 1.968 1.811 1.024 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
C6 MAHPD-JHP 2.480 1.811 1.299 1 SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N SR M4X8ISO14580 BLACK
• For user guide and accessories, see pages 137, 161-173
(1) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48)

141
FACE GROOVE-TURN
CDX

C#-GHAD-8
Holders with CAMFIX DAXN-DAXX
Exchangeable Shanks
for Grooving, Turning
CW DCONMS
and Facing Adapters WF
LF CDX - See specific adapter dimensions

M E T R I C
Designation DCONMS LF WF CW DAXN(1) DAXX(2) CDX(3) CP(4) CDI(5)
C5 GHAD-8 50.00 65.00 26.00 8.00 80.0 510.0 25.00 100 1
C6 GHAD-8 63.00 65.00 32.50 8.00 80.0 510.0 25.00 100 1

I N C H
Designation DCONMS LF WF CW DAXN(1) DAXX(2) CDX(3) CP(4) CDI(5)
C5 GHAD-8 1.968 2.559 1.024 .315 3.15 20.08 .984 1450 1
C6 GHAD-8 2.480 2.559 1.280 .315 3.15 20.08 .984 1450 1
• For user guide and accessories see pages 137, 161-173
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter
(3) Cutting depth maximum
(4) Coolant pressure (Bar)
(5) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • GAFG-R/L-8 (87)

Spare Parts

Designation
C#-GHAD-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0 SR 76-1022 EZA 125 EZ 125

LPR BD
C#-HATA
CAMFIX Toolholder with a
Serrated Connection Adaptation
DCONMS

M E T R I C
Designation DCONMS BD LPR CDI(1)
C6 HATA 63.00 106.00 66.00 1
(1) 1 - Hole for data chip, 0 - Without hole for data chip

Spare Parts

Designation
C6 HATA SR M8X45 DIN 913 SR M8X25 DIN913 HW 4.0 SR M6X6 DIN913 TL360 HW 3.0 BH NUT BHR MB80 SR M12X35DIN912 HW 10.0

142 ISCAR
 FACE GROOVE-TURN
C#-GHAPR/L-8 CDX
Perpendicular Holders with
CAMFIX Exchangeable DAXN-DAXX
Shanks for Grooving, Turning WF
DCONMS
and Facing Adapters
26 25.5 Right-hand shown
CW LF • CDX - See specific adapter dimensions

M E T R I C
Designation DCONMS LF WF CW DAXN(1) DAXX(2) CDX(3) CP(4) CDI(5)
C5 GHAPR/L-8 50.00 64.00 26.00 8.00 80.0 510.0 25.00 100 1
C6 GHAPR/L-8 63.00 75.00 33.00 8.00 80.0 510.0 25.00 100 1
• For user guide and accessories see pages 137, 161-173
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter
(3) Cutting depth maximum
(4) Coolant pressure (Bar)
(5) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • GAFG-R/L-8 (87)

Spare Parts

Designation
C5 GHAPR/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0 EZ 125
C6 GHAPR/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0

C#-GHAPR/L-8 CDX
Perpendicular Holders with
CAMFIX Exchangeable DAXN-DAXX
Shanks for Grooving, Turning WF
DCONMS
and Facing Adapters
1.02 1.00 Right-hand shown
CW LF • CDX - See specific adapter dimensions

I N C H
Designation DCONMS LF WF CW DAXN(1) DAXX(2) CDX(3) CP(4) CDI(5)
C5 GHAPR/L-8 1.968 2.520 1.024 .315 3.15 20.08 .984 1450 1
C6 GHAPR/L-8 2.480 2.953 1.299 .315 3.15 20.08 .984 1450 1
• For user guide and accessories see pages 137, 161-173
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter
(3) Cutting depth maximum
(4) Coolant pressure (PSI)
(5) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • GAFG-R/L-8 (87)

Spare Parts

Designation
C5 GHAPR/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0 EZ 125
C6 GHAPR/L-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0

143
FACE GROOVE-TURN
LPR
CDX
C#-HAD
DCONMS
Holders with CAMFIX
Exchangeable Tapered Shanks
for Internal Facing Adapters
WF

26 CDX - See specific adapter dimensions

M E T R I C

Designation DCONMS LPR WF CDI(1)

C4 HAD 40.00 60.00 18.0 1 SR 14-519 T-20/3 SR M4X6DIN912 HW 3.0
C5 HAD 50.00 60.00 18.0 1 SR 14-519 T-20/3 SR M4X6DIN912 HW 3.0
C6 HAD 63.00 60.00 22.0 1 SR 14-519 T-20/3 SR M4X6DIN912 HW 3.0
1 - Hole for data chip, 0 - Without hole for data chip
(1)

For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

LPR
CDX
C#-HAD
DCONMS
Holders with CAMFIX
Exchangeable Tapered Shanks
for Internal Facing Adapters
WF

1.02 CDX - See specific adapter dimensions

I N C H

Designation DCONMS LPR WF CDI(1)

C4 HAD 1.575 2.362 .709 1 SR 14-519 T-20/3 SR M4X6DIN912 HW 3.0
C5 HAD 1.968 2.362 .709 1 SR 14-519 T-20/3 SR M4X6DIN912 HW 3.0
C6 HAD 2.480 2.362 .866 1 SR 14-519 T-20/3 SR M4X6DIN912 HW 3.0
1 - Hole for data chip, 0 - Without hole for data chip
(1)

For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

C#-HAPR/L 8 DCONMS
Perpendicular Holders with
CAMFIX Exchangeable Shanks
for Internal Facing Adapters LF CDX
Right-hand shown
• CDX - See specific adapter dimensions

M E T R I C

Designation DCONMS LF CDI(1)

C4 HAPR/L 40.00 50.00 1 SR 14-519 T-20/3
C6 HAPR/L 63.00 50.00 1 SR 14-519 T-20/3

I N C H

Designation DCONMS LF CDI(1)

C4 HAPR/L 1.575 1.968 1 SR 14-519 T-20/3
C6 HAPR/L 2.480 1.968 1 SR 14-519 T-20/3
1 - Hole for data chip, 0 - Without hole for data chip
(1)

For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

144 ISCAR
 FACE GROOVE-TURN
DCONMS
C#-HFIR/L-MC
Boring Bars for Internal Grooving
LF
and Turning with CAMFIX BDRED
5.3
Exchangeable Shanks WF

CWN-CWX LDRED Right-hand shown

M E T R I C

Designation CWN(1) CWX(2) DCONMS WF LDRED LF BDRED CDI(3)

C4 HFIR/L-MC 3.00 6.00 40.00 11.30 52.0 80.0 25.00 1 SR M5X16 DIN912 HW 4.0 EZ 83
C5 HFIR-MC 3.00 6.00 50.00 11.30 52.0 80.0 25.00 1 SR M5X16 DIN912 HW 4.0 EZ 83
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools • After initial groove, no limitation to widening groove
outward or toward center
• For user guide, see pages 137, 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) 1 - Hole for data chip, 0 - Without hole for data chip

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)

DCONMS
C#-HFIR/L-MC
Boring Bars for Internal Grooving
LF
and Turning with CAMFIX BDRED
.21
Exchangeable Shanks WF

CWN-CWX LDRED Right-hand shown

I N C H

Designation CWN(1) CWX(2) DCONMS WF LDRED LF BDRED CDI(3)

C4 HFIR/L-MC .118 .236 1.575 .445 2.05 3.15 .984 1 SR M5X16 DIN912 HW 4.0 EZ 83
C5 HFIR-MC .118 .236 1.968 .445 2.05 3.15 .984 1 SR M5X16 DIN912 HW 4.0 EZ 83
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools • After initial groove, no limitation to widening groove
outward or toward center
• For user guide, see pages 137, 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) 1 - Hole for data chip, 0 - Without hole for data chip

For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • DGN-W (81) • HGPL (75)

145
FACE GROOVE-TURN

HSK
HSK A WH Complies l5
60°
with ICTM Standards
(ISO 12164-3)

d 2 d4 d 3 d9 max. d1 b5 b1
d15

f3
l1 f1
f2

HSK-A WH d1 h10 d2 d3 H10 d4 H11 d9 max d15 l1-0.2 l5 Js10 b1±0.04 b5±0.035 f1 -0.1 f2 min f3 ±0.1
63 63 48 34 40 62 M18X1 32 18.13 12.54 12.425 26 30 18
100 100 75 53 63 99 M24X1.5 50 28.56 20.02 19.91 29 34 20

HSK A TM Suitable 60˚

for all Multi-Tasking l5
Machine Models

d2 d4 d3 d9 max d1 b5 b1
d15

f3
l1 f1
f2
HSK A-TM d1 h10 d2 d3 H10 d4 H11 d9 max d15 l1-0.2 l5 JS10 b1±0.04 b5±0.035 f1-0.1 f2 min f3±0.1
63 63 48 34 40 52.8 M18x1 32 18.13 12.54 12.425 26 42 18

HSK A vs. HSK A...WH Tolerance

ISO key
STANDARD tolerance

HSK-A63 key slot

Tolerance Max. gap 0.33 tolerance

ICTM
STANDARD
(ISO
12164-3) Max. gap 0.015
HSK-A63WH Drive key slot range
Tolerance Drive key slot range
Max. gap 0.075 Drive key slot range

HSK-T (ISO 1264-3 T Type and ICTM Standard)

146 ISCAR
 FACE GROOVE-TURN
DCONMS
45º
HSK A63WH-MAHDR-45 45°

Holders with HSK Tapered CDX L5

LPR
Shanks for
MODULAR-GRIP, Parting, BD
Grooving and Facing Adapters L1
45°LF
CDX = See specific adapter dimensions • Right-handshown

M E T R I C
Designation DCONMS LPR L1 L5 LF BD CP(1) CDI(2)
HSK A63WH MAHDR 45 63.00 130.00 91.9 30.00 89.0 75.00 100 1

I N C H
Designation DCONMS LPR L1 L5 LF BD CP(1) CDI(2)
HSK A63WH MAHDR 45 2.480 5.118 3.618 1.181 3.504 2.953 1450 1
• A cooling tube must be used with all coolant through HSK spindles (should be ordered separately) • Complies with ICTM standard (ISO 12164-3)
(1) Coolant pressure (Bar)
(2) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
HSK A63WH MAHDR 45 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT HW 5.0 SR M6X6DIN551 14H/22H(b) SATZ-M8X1-M3
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) Used to prevent chips from entering the upper locking screw hole when it is not used for the adaptation; supplied in the attached plastic bag

HSK A63WH-MAHDOR DCONMS

Holders with HSK Exchangeable
Shanks for Parting, Grooving,
Turning and Facing Adapters
WF
CDX L5
LPR CDX = See specific adapter dimensions • Right-hand shown

M E T R I C

Designation DCONMS WF LPR L5 CDI(1)

HSK A63WH MAHDOR 63.00 29.0 130.00 30.00 1 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125

I N C H

Designation DCONMS WF LPR L5 CDI(1)

HSK A63WH MAHDOR 2.480 1.142 5.118 1.181 1 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125
• A cooling tube must be used with all coolant through HSK spindles (should be ordered separately) • Complies with ICTM standard (ISO 12164-3)
(1) 1 - Hole for data chip, 0 - Without hole for data chip
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole when it is not used for the adaptation; supplied in the attached plastic bag

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

147
FACE GROOVE-TURN
10°
DCONMS
HSK A63WH-MAHUR/L
Holders with HSK-T Shanks LPR
L5
for 10° Mounting on Mill-Turn 10°
Machines for Parting, Grooving,
WF
Turning and Facing Adapters L1
CDX
f1 CDX = See specific adapter dimensions • Right-handshown

M E T R I C
Designation DCONMS f1 WF LPR L1 L5 CP(1) CDI(2)
HSK A63WH MAHUR/L 10 63.00 113.1 29.00 130.00 49.4 30.00 100 1

I N C H
Designation DCONMS f1 WF LPR L1 L5 CP(1) CDI(2)
HSK A63WH MAHUR/L 10 2.480 4.453 1.142 5.118 1.945 1.181 1450 1
• A cooling tube must be used with all coolant through HSK spindles (should be ordered separately) • Complies with ICTM standard (ISO 12164-3)
(1) Coolant pressure (Bar)
(2) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
HSK A63WH MAHUR/L 10 SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZ 125
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole when it is not used for the adaptation; supplied in the attached plastic bag

HSK A-WH-TBK-R/L H DCONMS

Blocks with HSK Exchangeable
Tapered Shanks for Parting
and Grooving Blades
WF
L5
OHX LPR OHX = See specific blade dimensions • Right-hand shown

M E T R I C

Designation DCONMS LPR L5 WF H(1) CP(2) CDI(3)

HSK A63WH TBK 32R/L 63.00 138.00 30.00 32.0 32.0 100 1 BK 32-9 WEDG SR M6X16 DIN912 HW 5.0 EZ 125

I N C H

Designation DCONMS LPR L5 WF H(1) CP(2) CDI(3)

HSK A63WH TBK 32R/L 2.480 5.433 1.181 1.260 1.260 1450 1 BK 32-9 WEDG SR M6X16 DIN912 HW 5.0 EZ 125
• Complies with ICTM standard (ISO 12164-3) • Not suitable for ATC for some Multi-Tasking Machine models, please consult your MTB
• A cooling tube must be used with all coolant through HSK spindles (should be ordered separately)
(1) Blade size H has to fit this dimension
(2) Coolant pressure (Bar)
(3) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFFH (37) • PCHBR/L (125) • TNFFH-IQ (109)

148 ISCAR
 FACE GROOVE-TURN
LPR BD
HSK 63 HATA
HSK Toolholder with a Serrated
Connection Adaptation
DCONMS

M E T R I C
Designation DCONMS BD LPR
HSK63 HATA 63.00 106.00 86.00

Spare Parts

Designation
HSK63 HATA SR M6X6 DIN913 SR M8X25 DIN913 HW 4.0 SR M6X6 DIN913 TL360 HW 3.0 BH NUT BHR MB80 SR M12X35DIN912 HW 10.0 SR M8X45 DIN 913

149
FACE GROOVE-TURN

IM
LPR

IM-MAHD
Holders with an ISO 26622-1(*)
WF
Tapered Shank for Parting, DCONMS
Grooving, Turning and CDX = See specific adapter dimensions
CDX • Right-handshown
Facing Adapters
M E T R I C
Designation DCONMS LPR WF CDI(1)
IM40 MAHD 40.00 43.00 18.0 0
IM50 MAHD 50.00 47.00 23.0 0
IM63 MAHD 63.00 52.00 29.0 0

I N C H
Designation DCONMS LPR WF CDI(1)
IM40 MAHD 1.575 1.693 .709 0
IM50 MAHD 1.968 1.850 .906 0
IM63 MAHD 2.480 2.047 1.142 0
• (*) Tools with orientation holes in the flange groove can be supplied on request
(1) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
IM-MAHD SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(c) HW 5.0 SR M6X6DIN551 14H/22H(d) SR 76-1022 EZA 125 EZ 125
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(d) Used to prevent chips from entering the upper locking screw hole when it is not used for the adaptation; supplied in the attached plastic bag

150 ISCAR
 FACE GROOVE-TURN
LPR

IM-MAHPD DCONMS
WF
Perpendicular Holders with
an ISO 26622-1(*) Tapered CDX
Shank for Parting, Grooving, CDX = See specific adapter dimensions
• Right-hand shown
Turning and Facing Adapters
M E T R I C
Designation DCONMS LPR WF CDI(1)
IM40 MAHPD 40.00 44.00 25.00 0
IM50 MAHPD 50.00 45.00 26.00 0
IM63 MAHPD 63.00 45.00 33.00 0

I N C H
Designation DCONMS LPR WF CDI(1)
IM40 MAHPD 1.575 1.732 .984 0
IM50 MAHPD 1.968 1.772 1.024 0
IM63 MAHPD 2.480 1.772 1.299 0
• (*) Tools with orientation holes in the flange groove can be supplied on request
(1) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
IM-MAHPD SR M5-04451 T-20/5 SR 14-519(a) SR M6X20-XT(b) HW 5.0 SR M6X6DIN551 14H/22H(c) EZP 5 EZ 125
(a) For DGAD, HGAD and PCADR/L adapters; supplied in the attached plastic bag
(b) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools
(c) Used to prevent chips from entering the upper locking screw hole when it is not used for the adaptation; supplied in the attached plastic bag

CDX

IM-GHAD-8
Holders with an ISO 26622-1(*) DAXN-DAXX
DCONMS
Tapered Shank for Grooving, WF
Turning and Facing Adapters CW CDX LF
CDX - See specific adapter dimensions

M E T R I C
Designation DCONMS CW LF WF DAXN(1) DAXX(2) CDX(3) CDI(4)
IM50 GHAD-8 50.00 8.00 60.00 26.00 80.0 510.0 25.00 0
IM63 GHAD-8 63.00 8.00 65.00 32.50 80.0 510.0 25.00 0

I N C H
Designation DCONMS CW LF WF DAXN(1) DAXX(2) CDX(3) CDI(4)
IM50 GHAD-8 1.968 .315 2.362 1.024 3.15 20.08 .984 0
IM63 GHAD-8 2.480 .315 2.559 1.280 3.15 20.08 .984 0
• (*) Tools with orientation holes in the flange groove can be supplied on request
(1) Minimum axial grooving diameter
(2) Maximum axial grooving diameter
(3) Cutting depth maximum
(4) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: • GAFG-R/L-8 (87)

Spare Parts

Designation
IM-GHAD-8 SR 14-519 T-20/5 SR M6X25 DIN912 HW 5.0 SR 76-1022 EZA 125 EZ 125

151
FACE GROOVE-TURN
LPR
CDX
DCONMS
IM-HAD
Holders with an ISO 26622-1(*) WF
Tapered Shank for Internal
Facing Adapters
26 CDX - See specific adapter dimensions

M E T R I C

Designation DCONMS LPR WF CDI(1)

IM40 HAD 40.00 60.00 18.0 0 SR 14-519 T-20/3 HW 3.0 SR M4X6DIN912
IM50 HAD 50.00 60.00 18.0 0 SR 14-519 T-20/3 HW 3.0 SR M4X6DIN912

I N C H

Designation DCONMS LPR WF CDI(1)

IM40 HAD 1.575 2.362 .709 0 SR 14-519 T-20/3 HW 3.0 SR M4X6DIN912
IM50 HAD 1.968 2.362 .709 0 SR 14-519 T-20/3 HW 3.0 SR M4X6DIN912
• (*) Tools with orientation holes in the flange groove can be supplied on request
(1) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

8
DCONMS
IM-HAPR/L
Perpendicular Holders with an
ISO 26622-1 (*) Tapered Shank LF CDX CDX - See specific adapter dimensions
for Internal Facing Adapters • Right-hand shown

M E T R I C

Designation DCONMS LF CDI(1)

IM40 HAPR/L 40.00 50.00 0 SR 14-519 T-20/3
IM50 HAPR 50.00 50.00 0 SR 14-519 T-20/3

I N C H

Designation DCONMS LF CDI(1)

IM40 HAPR/L 1.575 1.968 0 SR 14-519 T-20/3
IM50 HAPR 1.968 1.968 0 SR 14-519 T-20/3
• (*) Tools with orientation holes in the flange groove can be supplied on request
(1) 1 - Hole for data chip, 0 - Without hole for data chip

For tools, see pages: HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HGAER/L-3 (52) • HGAIR/L-3 (57)

152 ISCAR
 FACE GROOVE-TURN
SQUARE SHANK HOLDERS
MAHPR/L HF H
Holders for Perpendicularly
Mounted Adapters for all LH HBH
OAL
GRIP Systems
B

Right-hand shown

M E T R I C
Designation H B HF OAL LH HBH
MAHPR/L 20 20.0 20.0 20.0 140.00 25.0 10.0
MAHPR/L 25 25.0 25.0 25.0 140.00 25.0 5.0
MAHPR/L 32 32.0 32.0 32.0 150.00 25.0 -
For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
MAHPR/L SR M5-04451 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
(a) For CGPAD, HGPAD, TGPAD and HFPAD adapters. Supplied with the tools.

MAHPR/L HF H
Holders for Perpendicularly
Mounted Adapters for all LH HBH
OAL
GRIP Systems
B

Right-hand shown

I N C H
Designation H B HF OAL LH HBH
MAHPR/L 19 (1) .750 .750 .750 6.000 .980 .43
MAHPR/L 25.4 1.000 1.000 1.000 6.000 .980 .20
MAHPR/L 31.7 1.250 1.250 1.250 7.000 .980 -
Supplied on request only.
(1)

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
MAHPL 19 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
MAHPR 19 SR M5-04451 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
MAHPR/L 25.4 SR M5-04451 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
MAHPR/L 31.7 SR M5-04451 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
(a) For CGPAD, HGPAD, TGPAD and HFPAD adapters. Supplied with the tools.

153
FACE GROOVE-TURN

HF H Bar Max

G 1/8"-28 LH HBH
MAHPR/L-JHP OAL
Holders with High-Pressure
Coolant Channels for 4.5 B
MODULAR-GRIP Perpendicularly
Right-hand shown
Mounted Adapters
M E T R I C
Designation H B OAL LH HBH HF
MAHPR/L 20-JHP 20.0 20.0 140.00 28.0 10.0 20.0
MAHPR/L 25-JHP 25.0 25.0 140.00 28.0 5.0 25.0
MAHPR/L 32-JHP 32.0 32.0 150.00 - - 32.0
• For user guide and accessories, see pages 161-173
For tools, see pages: • HFPAD-JHP (48) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

SR M6X20-XT
(Key: HW 5.0)

OR 5X1N

SR M6X12DIN6912
(Key: HW 5.0) PLUG G1/8ISO1179
SR M5X04451 (Key: HW 5.0)
(Key: T-20/5)

Spare Parts

Designation
MAHPR/L-JHP SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N PLG 1/8ISO1179

HF H PSI Max

G 1/8"-28 LH HBH
MAHPR/L-JHP OAL
Holders with High-Pressure
Coolant Channels for .177 B
MODULAR-GRIP Perpendicularly
Mounted Adapters
I N C H
Designation H B OAL LH HBH HF
MAHPR/L 19-JHP .750 .750 5.500 1.100 .39 .750
MAHPR/L 25.4-JHP 1.000 1.000 5.500 1.100 .20 1.000
MAHPR/L 31.7-JHP 1.250 1.250 6.000 - - 1.250
For tools, see pages: • HFPAD-JHP (48) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

SR M6X20-XT
(Key: HW 5.0)

OR 5X1N

SR M6X12DIN6912
(Key: HW 5.0) PLUG G1/8ISO1179
SR M5X04451 (Key: HW 5.0)
(Key: T-20/5)

Spare Parts

Designation
MAHPR/L-JHP SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N PLG 1/8ISO1179

154 ISCAR
 FACE GROOVE-TURN
H OAH
HBH
LH
OAW
MAHPR/L-XL-JHP OAL
Holders with High-Pressure
B HF
Coolant Channels for
MODULAR-GRIP Perpendicularly MHD L5
MHD_2 Right-hand shown
Mounted Adapters
M E T R I C
Designation H B LH OAL HBH OAH OAW HF L5 MHD MHD_2
MAHPR/L-XL-20-JHP-MCG 20.0 20.0 23.0 120.00 24.0 53.00 45.00 20.0 29.00 50.00 85.00
MAHPR/L-XL-25-JHP-MCG 25.0 25.0 15.0 120.00 19.0 53.00 45.50 25.0 35.00 50.00 90.00
For tools, see pages: • HFPAD-JHP (48) • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHPR/L-XL-20-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X4 DIN913 TL360 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377
MAHPR/L-XL-25-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X4 DIN913 TL360 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377

H OAH
HBH
LH
OAW
MAHPR/L-XL-JHP OAL
Holders with High-Pressure
B HF
Coolant Channels for
MODULAR-GRIP Perpendicularly MHD L5
MHD_2 Right-hand shown
Mounted Adapters
I N C H
Designation H B LH OAL HBH OAH OAW HF L5 MHD MHD_2
MAHPR/L-XL-19-JHP-MCG .750 .750 .591 4.724 1.000 2.087 1.772 .750 1.142 1.968 3.346
MAHPR/L-XL-20-JHP-MCG .787 .787 .906 4.724 .945 2.087 1.772 .787 1.142 1.968 3.346
MAHPR/L-XL-25-JHP-MCG .984 .984 .591 4.724 .748 2.087 1.791 .984 1.378 1.968 3.543
MAHPR/L-XL-25.4-JHP-MCG 1.000 1.000 .591 4.724 .748 2.087 1.791 1.000 1.378 1.968 3.543
For tools, see pages: • HFPAD-JHP (48) • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHPR/L-XL-19-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X3 DIN913 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377
MAHPR/L-XL-20-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X4 DIN913 TL360 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377
MAHPR/L-XL-25-JHP-MCG SR M5-04451 T-20/5 SR M6X16 DIN912 HW 5.0 OR 5X1N SR M4X4 DIN913 TL360 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377
MAHPR/L-XL-25.4-JHP-MCG SR M5-04451 T-20/5 SR M6X20 DIN912 HW 5.0 OR 5X1N SR M4X3 DIN913 SR M6X6 DIN913 TL360 PLG G1/8 TL360 SUPPORT MG-XL-5113377

155
FACE GROOVE-TURN

MAHR/L
H HF
Adapter Holders for
all GRIP Systems OAL
HBH

B WF (shank) WF (assembly)
Left-hand shown •
WF (adapter)
WF(assembly)=WF(shank)+WF(adapter)

M E T R I C
Designation H B HF OAL HBH WF(1)
MAHR/L 20 20.0 20.0 20.0 130.00 10.0 17.1
MAHR/L 25 25.0 25.0 25.0 130.00 5.0 22.1
MAHR/L 32 32.0 32.0 32.0 140.00 - 29.1
WF(shank)
(1)

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
MAHR/L SR M5-04451 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
(a) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools

MAHR/L
H HF
Adapter Holders for
all GRIP Systems OAL
HBH

B WF (shank) WF (assembly)
Left-hand shown •
WF (adapter)
WF(assembly)=WF(shank)+WF(adapter)

I N C H
Designation H B HF OAL HBH WF(2)
MAHR/L 19 (1) .750 .750 .750 5.600 .43 .640
MAHR/L 25.4 1.000 1.000 1.000 5.600 .20 .890
MAHR/L 31.7 1.250 1.250 1.250 6.600 - 1.140
MAHR/L 38.1 (1) 1.500 1.500 1.500 6.600 - 1.390
Supplied on request only.
(1)

WF(shank)
(2)

For tools, see pages: • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
MAHR/L SR M5-04451 T-20/5 SR 14-519 SR M6X20-XT(a) HW 5.0 SR M6X6DIN551 14H/22H
(a) For CGPAD, HGPAD, TGPAD and HFPAD adapters; supplied with the tools

156 ISCAR
 FACE GROOVE-TURN
H HF
Bar Max

HBH G 1/8"-28
MAHR/L-JHP OAL
Holders with High-Pressure HBKW
Coolant Channels for B WF (shank) WF (assembly)
MODULAR-GRIP Adapters Left-hand shown •
2.3 WF (adapter) WF(assembly)=WF(shank)+WF(adapter)

M E T R I C
Designation H B OAL HBH WF(1) HBKW HF
MAHR/L 20-JHP 20.0 20.0 130.00 10.0 15.1 16.50 20.0
MAHR/L 25-JHP 25.0 25.0 130.00 5.0 20.1 11.50 25.0
MAHR/L 32-JHP 32.0 32.0 140.00 - 27.1 4.50 32.0
• For user guide and accessories, see pages 161-173
(1) WF(shank)

For tools, see pages: • HFPAD-JHP (48) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

PLUG G1/8ISO1179 SR M6X20-XT

(Key: HW 5.0) (Key: HW 5.0)

OR 5X1N

SR M6X12DIN6912
(Key: HW 5.0)
SR M5-04451
(Key: T-20/5)
Spare Parts

Designation
MAHR/L-JHP SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N PLG 1/8ISO1179

H HF
PSI Max

HBH G 1/8"-28
MAHR/L-JHP OAL
Holders with High-Pressure HBKW
Coolant Channels for B WF (shank) WF (assembly)
Left-hand shown •
MODULAR-GRIP Adapters .090 WF (adapter) WF(assembly)=WF(shank)+WF(adapter)

I N C H
Designation H B OAL HBH WF(1) HBKW HF
MAHR/L 19-JHP .750 .750 5.000 .19 .560 .650 .750
MAHR/L 25.4-JHP 1.000 1.000 5.000 .20 .810 .453 1.000
MAHR/L 31.7-JHP 1.250 1.250 5.500 - 1.060 .177 1.250
WF(shank)
(1)

For tools, see pages: • HFPAD-JHP (48) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

PLUG G1/8ISO1179 SR M6X20-XT

(Key: HW 5.0) (Key: HW 5.0)

OR 5X1N

SR M6X12DIN6912
(Key: HW 5.0)
SR M5-04451
(Key: T-20/5)
Spare Parts

Designation
MAHR/L-JHP SR M5-04451 T-20/5 SR M6X12DIN6912 SR M6X20-XT HW 5.0 OR 5X1N PLG 1/8ISO1179

157
FACE GROOVE-TURN

H HF Bar Max

HBH
MAHR/L-JHP-MC OAL
Holders with Bottom Inlets for
High-Pressure Coolant Channels HBKW WF (shank)
B WF (assembly)
Carrying MODULAR-GRIP Left-hand shown
1.2 WF (adapter) • WF(assembly)=WF(shank)+WF(adapter)
Grooving and Turning Adapters
Designation H B OAL HBH WF(1) HBKW HF
MAHR/L 20-JHP-MC 20.0 20.0 98.00 10.0 14.0 6.00 20.0
MAHR/L 25-JHP-MC 25.0 25.0 98.00 5.0 19.0 - 25.0
• For CDX, refer to the adapters data.
(1) WF(shank)

For tools, see pages: HFPAD-JHP (48) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50)

Spare Parts

Designation
MAHR/L-JHP-MC SR M6X20-XT HW 5.0 SR M5-04451 T-20/5 SR M6X12DIN6912 OR 5X1N

158 ISCAR
 FACE GROOVE-TURN
HF H
MAHR/L-MG-XL-JHP Bar Max
Holders with High-Pressure HBH
OAL G1/8x3
Coolant Channels for HBKW
Interchangeable Adapters WF (shank)
Right-hand B
Left-hand
WF(assembly)=WF(shank)+WF(adapter)

M E T R I C
Designation H B OAL HBH WF HBKW
MAHR/L 20-MG-XL-JHP 20.0 20.0 149.10 24.0 14.0 4.00
MAHR/L 25-MG-XL-JHP 25.0 25.0 149.10 19.0 19.0 9.00
• For user guide and accessories, see pages 161-173
For tools, see pages: • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHR/L 20-MG-XL-JHP SR M6X12DIN6912-P HW 5.0 SR M5-04451 T-20/5 SR M6X14-XT DIN 912 OR 5X1N PLG G1/8 TL360
MAHR/L 25-MG-XL-JHP SR M6X12DIN6912-P HW 5.0 SR M5-04451 T-20/5 SR M6X14-XT DIN 912 OR 5X1N PLG G1/8 TL360

HF H
MAHR/L-MG-XL-JHP PSI
Holders with High-Pressure HBH
OAL G1/8x3
Coolant Channels for HBKW
Interchangeable Adapters
Right-hand WF B
Left-hand
WF(assembly)=WF(shank)+WF(adapter)

I N C H
Designation H B OAL HBH WF HBKW
MAHR/L 19-MG-XL-JHP .750 .750 5.870 .98 .512 .118
MAHR/L 25.4-MG-XL-JHP 1.000 1.000 5.870 .73 .772 .370
• For user guide and accessories, see pages 161-173
For tools, see pages: • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHL 19-MG-XL-JHP SR M6X12DIN6912-P HW 5.0 SR M5-04451 T-20/5 SR M6X14-XT DIN 912 OR 5X1N PLG G1/8 TL360
MAHR 19-MG-XL-JHP SR M6X12DIN6912 HW 5.0 SR M5-04451 T-20/5 SR M6X14-XT DIN 912 OR 5X1N PLG G1/8 TL360
MAHR/L 25.4-MG-XL-JHP SR M6X12DIN6912-P HW 5.0 SR M5-04451 T-20/5 SR M6X14-XT DIN 912 OR 5X1N PLG G1/8 TL360

159
FACE GROOVE-TURN
Coolant inlet

MAHR/L-MG-XL-JHP-MC H H CDX
Bar Max
Holders with Bottom Inlets HBH
for High-Pressure Coolant f3 OAL
Channels Carrying Parting
Right-hand WF B
and Grooving Adapters
Left-hand
WF(assembly)=WF(shank)+WF(adapter)

M E T R I C
Designation H B OAL HBH WF HBKW
MAHR/L 20-MG-XL-JHP-MC 20.0 20.0 116.10 10.0 14.0 4.00
MAHR/L 25-MG-XL-JHP-MC 25.0 25.0 114.00 10.0 19.0 9.00
• For CDX, refer to the adapters data
For tools, see pages: • TNFPAD-XL-JHP (113)

Spare Parts

Designation
MAHR/L-MG-XL-JHP-MC SR M6X14-XT DIN 912 HW 5.0 SR M5-04451 T-20/5 SR M6X12DIN6912-P OR 5X1N

160 ISCAR
 USER GUIDE

161
FACE GROOVE-TURN
 USER GUIDE
FACE GROOVE-TURN

Machining Data for Face Machining

Tensile Strength Material

ISO

Material Condition [N/mm2] Hardness HB Group No.

< 0.25 %C Annealed 420 125 1
>= 0.25 %C Annealed 650 190 2
Non-alloy steel and cast
< 0.55 %C Quenched and tempered 850 250 3
steel, free cutting steel
>= 0.55 %C Annealed 750 220 4
Quenched and tempered 1000 300 5
Annealed 600 200 6
Low alloy steel and cast steel (less 930 275 7
P than 5% of alloying elements) Quenched and tempered 1000 300 8
1200 350 9
Annealed 680 200 10
High alloyed steel, cast steel, and tool steel
Quenched and tempered 1100 325 11

Ferritic/martensitic 680 200 12

Stainless steel and cast steel
Martensitic 820 240 13

M Stainless steel and cast steel Austenitic 600 180 14

Ferritic/pearlitic 180 15
Cast iron nodular (GG)
Pearlitic/ Martensitic 260 16
Ferritic 160 17
K Grey cast iron (GGG)
Pearlitic 250 18
Ferritic 130 19
Malleable cast iron
Pearlitic 230 20

Not cureable 60 21
Aluminum-wrought alloys
Cured 100 22
<=12% Si Not cureable 75 23
Aluminum-cast-alloys Cured 90 24
>12% Si High temperature 130 25
N
>1% Pb Free cutting 110 26
Copper alloys Brass 90 27
Electrolitic copper 100 28
Duroplastics, fiber plastics 29
Non-metallic
Hard rubber 30

Fe based Annealed 200 31

Cured 280 32
High temp. alloys Annealed 250 33
S Ni or Co based Cured 350 34
Cast 320 35
RM 400 36
Titanium Ti alloys
Alpha+beta alloys cured RM 1050 37

Hardened 55 HRC 38
Hardened steel
Hardened 60 HRC 39
H
Chilled cast iron Cast 400 40
Cast iron Hardened 55 HRC 41

162 ISCAR
 USER GUIDE

FACE GROOVE-TURN
Material
No. IC228/528 IC830 IC354 IC908 IC808 IC8250
1 85 - 125 90 - 135 95 - 145 120 - 180 125 - 190 180 - 270
2 75 - 110 80 - 115 90 - 125 110 - 155 115 - 165 165 - 230
3 60 - 85 65 - 95 70 - 100 85 - 125 90 - 130 125 - 185
4 65 - 100 70 - 110 75 - 115 95 - 145 100 - 150 140 - 215
5 50 - 85 55 - 90 60 - 95 75 - 120 80 - 125 110 - 180
6 65 - 100 70 - 110 75 - 115 95 - 145 100 - 150 140 - 215
7 50 - 85 55 - 95 60 - 100 75 - 125 80 - 130 110 - 185
8 50 - 85 55 - 90 60 - 95 75 - 120 80 - 125 110 - 180
9 50 - 75 50 - 80 55 - 90 70 - 110 75 - 115 105 - 165
10 75 - 110 80 - 115 90 - 125 110 - 155 115 - 165 165 - 230
11 50 - 75 50 - 80 55 - 90 70 - 110 75 - 115 105 - 165

IC806 IC808 IC354 IC830 IC20

12 110 - 200 100 - 180 80 - 145 75 - 135 50 - 90
13 100 - 185 90 - 170 70 - 135 65 - 125 45 - 85

IC806 IC808 IC354 IC830 IC20

14 90 - 170 80 - 155 65 - 125 60 - 115 40 - 75

IC5010 IC428 IC8250 IC808 IC20

15 135 - 255 125 - 230 110 - 205 85 - 160 60 - 115
16 120 - 180 110 - 160 100 - 145 75 - 110 55 - 80
17 130 - 215 120 - 195 110 - 175 85 - 135 60 - 95
18 105 - 170 95 - 155 85 - 140 65 - 110 45 - 75
19 160 - 265 145 - 240 130 - 215 100 - 170 70 - 120
20 130 - 215 120 - 195 110 - 175 85 - 135 60 - 95

IC808 IC20
21 330 - 990 300 - 900
22 250 - 825 225 - 750
23 250 - 825 225 - 750
24 165 - 495 150 - 450
25 165 - 330 150 - 300
26 165 - 330 150 - 300
27 120 - 250 110 - 225
28 80 - 165 75 - 150
29 40 - 165 35 - 150
30

IC806 IC908 IC808 IC830 IC20

31 45 - 70 35 - 55 35 - 60 25 - 40 25 - 40
32 30 - 50 25 - 40 25 - 40 20 - 30 15 - 30
33 30 - 50 25 - 40 25 - 40 20 - 30 15 - 30
34 25 - 45 20 - 35 20 - 35 15 - 25 15 - 25
35 20 - 30 15 - 25 15 - 25 10 - 20 10 - 15
36 105 - 180 85 - 145 90 - 150 65 - 110 60 - 100
37 40 - 50 30 - 40 30 - 40 25 - 35 35 - 45

IC808 IC20
38 25-30 20-30
39 20-30 15-25
40 30-45 30-40
41 25-30 25-30

163
 USER GUIDE
FACE GROOVE-TURN

Machining Data for Face Machining

MIFR/
GFQR PICCO MEFL MIFR 10 MIFR 15
Tensile Cutting IC528 IC228 8 IC908 IC908 IC908
Strength Hardness Material Speed Feed Feed Feed Feed Feed
ISO

Material Condition [N/mm2] HB No. (m/min) (mm/rev) (mm/rev) (mm/rev) (mm/rev) (mm/rev)
< 0.25 %C Annealed 420 125 1
80-180 0.02-0.08 0.015-0.05
>= 0.25 %C Annealed 650 190 2
Non-alloy Quenched
steel and < 0.55 %C and 850 250 3
80-130 0.02-0.06 0.015-0.04
cast steel, tempered
free cutting >= 0.55 %C Annealed 750 220 4
steel Quenched
and 1000 300 5 80-120 0.02-0.06 0.015-0.04
tempered 0.015-0.08 0.03-0.10 0.03-0.08
Annealed 600 200 6 80-140 0.02-0.08 0.015-0.04
P Low alloy and cast
Quenched 930 275 7 80-140 0.02-0.08 0.015-0.04
steel (less than 5% of
and 1000 300 8 80-120 0.02-0.06 0.015-0.03
alloying elements)
tempered 1200 350 9 80-120 0.02-0.05 0.015-0.03
Annealed 680 200 10 80-140 0.02-0.08 0.015-0.04
High alloyed steel, cast Quenched
steel, and tool steel and 1100 325 11 80-120 0.02-0.08 0.015-0.03
tempered
Ferritic/
Stainless steel 680 200 12 40-120 0.02-0.08 0.015-0.04 0.015-0.07 0.03-0.08 0.02-0.05
martensitic
and cast steel
Martensitic 820 240 13 40-120 0.02-0.07 0.015-0.04 0.015-0.07 0.03-0.08 0.02-0.05
Stainless steel
M Austenitic 600 180 14 40-100 0.02-0.06 0.015-0.03 0.015-0.07 0.03-0.08 0.02-0.05
and cast steel
Ferritic/
180 15 80-140 0.02-0.08 0.015-0.05
pearlitic
Cast iron nodular (GG)
Pearlitic/
260 16 80-120 0.02-0.07 0.015-0.04
Martensitic
K Ferritic 160 17 80-140 0.02-0.08 0.015-0.04
0.02-0.10 0.05-0.12 0.04-0.10
Grey cast iron (GGG)
Pearlitic 250 18 80-120 0.02-0.07 0.015-0.04
Ferritic 130 19 80-140 0.02-0.06 0.015-0.04
Malleable cast iron
Pearlitic 230 20 80-120 0.02-0.07 0.015-0.04
Not cureable 60 21 150-320 0.02-0.08 0.015-005
Aluminum-wrought alloys
Cured 100 22 100-250 0.02-0.08 0.015-005
<=12% Si Not cureable 75 23 150-300 0.02-0.08 0.015-005
Aluminum- Cured 90 24 150-300 0.02-0.08 0.015-005
cast-alloys High
>12% Si 130 25 100-150 0.02-0.08 0.015-005
temperature
N >1% Pb Free cutting 110 26 80-230 0.02-0.08 0.015-005 0.02-0.10 0.05-0.15 0.05-0.12
Copper Brass 90 27 70-200 0.02-0.08 0.015-005
alloys Electrolitic
100 28 50-180 0.02-0.08 0.015-005
copper
Duroplastics,
29
Non-metallic fiber plastics
Hard rubber 30
Fe based Annealed 200 31 20-40 0.02-0.06 0.015-0.04
Cured 280 32 15-30 0.02-0.06 0.015-0.04
High temp.
Annealed 250 33 15-20 0.02-0.06 0.015-0.04
alloys Ni or Co
Cured 350 34 15-20 0.02-0.06 0.015-0.04
S based 0.015-0.7 0.02-0.08 0.02-0.05
Cast 320 35 15-20 0.02-0.06 0.015-0.04
RM 400 36 40-120 0.02-0.06 0.015-0.04
Titanium Ti alloys Alpha+beta
RM 1050 37 20-50 0.02-0.06 0.015-0.04
alloys cured
Hardened 55 HRC 38
Hardened steel
Hardened 60 HRC 39
H
Chilled cast iron Cast 400 40
Cast iron Hardened 55 HRC 41

164 ISCAR
 USER GUIDE

FACE GROOVE-TURN
ISCAR Face Gooving Grades Chart
Grade ISO Grade Description Coating Layers Coating Color*
P20-P40
M20-M30
A tough substrate with PVD coating, suitable for general use on
IC354 a wide range of carbon steels, alloy steels and stainless steel at
moderate speeds and feeds.
TiCN
Base

A hard submicron grain size substrate with PVD coating and a

M05-M15 special SUMOTEC surface treatment.
IC806 Excellent for machining high temperature alloys and Titanium
alloys, at moderate to relatively high cutting speeds. TiAlN
S10-S20 Features high wear resistance and plastic deformation durability. AlTiN
Base
P10-P20
A hard submicron grain size substrate with PVD coating and a
M05-M15 special SUMOTEC surface treatment. Suitable for machining
K15-K30 steels, alloy steels, austenitic stainless steel, high temperature
IC807
alloys and hard steels at moderate to relatively high cutting TiN
speeds under stable conditions. Features high wear resistance
PVD COATED

S10-S20 TiAlN
and plastic deformation durability.
H05-H15 Base
P15-P30
A tough submicron grain size substrate with PVD coating and a
M20-M30 special SUMOTEC surface treatment. Recommended for general
K20-K40 use for a large variety of applications and materials such as
IC808
steels, alloy steels, austenitic stainless steel and high temperature TiN
S15-S30 alloys at moderate cutting speeds and feeds. Features high wear TiAIN
resistance and chipping durability.
H20-H30 Base
P30-P45
A tough substrate with PVD coating and a special SUMOTEC
M25-M40 surface treatment. Suitable for machining steel and stainless
steel at low to medium cutting speeds and moderate to high
IC830
feeds. The grade features high toughness and recommended for TiN
S20-S30 interrupted cuts and machining under unstable conditions. May TiAlN
be used on high temperature alloys at low cutting speeds.
Base
P15-P30
M20-M30 A tough submicron grain size substrate with PVD coating,
K20-K40 recommended for general use in a large variety of operations and
IC908 materials such as steels, alloy steels, austenitic stainless steel and
high temperature alloys at moderate cutting speeds.
S15-S30 Features high wear resistance and chipping durability. TiAlN
H20-H30 Base
* For coated grades

165
 USER GUIDE
FACE GROOVE-TURN

ISCAR Face Gooving Grades Chart

Grade ISO Grade Description Coating Layers Coating Color*

A hard substrate with MTCVD coating with a special SUMOTEC

K10-K20 surface treatment. Recommended for machining gray and nodular TiN
IC5010
cast iron at moderate to high cutting speeds, provides very good Al2O3
resistance to chipping. TiCN
Base
P15-P35
M15-M25 A tough substrate with a cobalt enriched layer and MTCVD
coating with a special SUMOTEC surface treatment. TiN
IC8250 Recommended for general use machining of steels, alloy steels
and martensitic stainless steel in a wide range of conditions. Al2O3
Features high toughness and good wear resistance. TiCN
Base
CVD COATED

A tough substrate with multilayer CVD coating. Recommended for

K10-K25 machining gray and nodular cast iron at medium to high cutting
IC418
speeds. Can be used for interrupted cuts and under heavy Al2O3
machining conditions. Tic
Base

K05-K20 A hard substrate with multilayer CVD coating.

IC428 Recommended for machining gray and nodular cast
iron at moderate to high cutting speeds. Al2O3
Tic
H15-H25 Base
P10-P25
A hard substrate with a cobalt enriched layer and MTCVD
K10-K15 coating. Recommended for high speed machining of steels, TiN
IC9015
alloy steels and martensitic stainless steel with moderate feeds Al2O3
at stable conditions. TiCN
Base
* For coated grades

Grade ISO Grade Description Coating Layers Uncoated

M15-M30
A tough uncoated submicron carbide grade, suitable for steels,
IC08 stainless steel and high temperature alloys at low cutting speeds.
N10-N25 Good choice for non-ferrous materials.
S20-S30
UNCOATED

Base

A hard-uncoated carbide grade for machining aluminum and

K10-K20 other non-ferrous materials at medium to high cutting speeds.
IC20 Can be used for cast iron at low cutting speeds.
N05-N25 Suitable also for machining high temperature and Titanium alloys,
S10-S20 at low cutting speeds.
H10-H20 Base

166 ISCAR
 USER GUIDE

FACE GROOVE-TURN
Clamping the Insert Face Machining Guide
Clamping an insert correctly into the holder Tool Selection - Follow these recommendations
is necessary for stable machining. to choose the right tool for high peformance.
• Be sure that the seat is clean of dirt and swarf.
• In the first stage of clamping, ease the insert gently into
place. Make sure that the prismatic surfaces match.

Screw Clamping Torque W

Insert Width Nxm
3 4-5
4 5-6
5 6-7
6/8 7-9 Choose the widest possible insert and tool, according
CGFG 51... 4-6 to the cutting width and geometry to be machined.
The unique chipformer is designed for deep
grooving and face turning both toward and away
from the center with excellent chip formation.

T max

Choose the shortest tool blade overhang,

according to the maximum depth required.

Dmin Minor
Diameter

Major
Diameter

Choose the tool range with the largest

diameter, depending on the initial grooving
diameter required in the application.
Remark: On integral shank tools the given range
refers to the holder capacity.
HELI-FACE HFPR/L HELI-GRIP
& HGPL Type GRIP...Y Type Tool Adjustment - Prior to machining, check
and adjust the following tool positions.

For general use in turning The “all in one” insert for

& grooving on all types of parting, external grooving
materials. Use for deep and turning, internal
grooving in low-to-medium grooving and turning, face
feeds 0.04-0.15 mm/rev. grooving and turning. Check the cutting edge height at center line, machine
Min grooving dia. 12 mm. in light turning down to center and check for burr.

DO-GRIP DO-GRIP
DGN...C Type DGN...J Type

For grooving operations For grooving operations // 0.015 4 mm

only. Strong cutting edge only. Positive rake, for soft
for hard materials and materials in low-to-medium Check parallelism of the cutting edge and machined
tough applications in feeds 0.05-0.15 mm/rev. surface. Correct position can guarantee good surface
feeds 0.1-0.2 mm/rev. quality when face turning in both directions.

167
 USER GUIDE
FACE GROOVE-TURN

Face Machining Guide Optimizing the Machining Sequence

Recommended machining sequence in roughing Recommended machining sequence
operation using multifunction HELI-FACE tools. using multifunction tools.
Groove at the initial diameter up to the depth of Groove at the initial diameter to the final depth of
cut selected for the next step in face turning. the groove and continue face turning away from
the center to the tangential point on the radius.

1
1

Continue with face turning away from the center.

Finish major diameter toward the
bottom and generate the radius.

2
2

After rapid positioning back into initial groove,

continue with face turning to center.
Position the tool in rapid movement in the initial
groove, continue face turning to center, without
3 touching the machined roughing steps on the wall.

Note: When face grooving, reduce the speed by 40% in relation to that
used in face turning.

Finish boring the minor diameter to

the bottom, up to final depth.

Note: When face grooving, reduce the speed by 40% in relation to that
used in face turning.

168 ISCAR
 USER GUIDE

FACE GROOVE-TURN
The Multifunction Advantage The Multifunction Advantage
The HELI-FACE internal boring bar HFIR/L MC type This workpiece was machined using
with internal coolant can replace the three different three different conventional tools.
ISO tools and shorten machining time by 20%. An indexable drill for bottom drilling.

1
1

A single multifunction tool machines the whole part: A standard internal boring bar with a trigon
grooving, face turning and chamfering, replacing three insert for roughing and finishing.
ISO tools and reducing machining time by 40%.

2 2

A single integral HELI-FACE tool HFHPL-M A standard internal boring bar with a trigon insert
replaces three ISO tools and reduces for bottom machining. This operation requires
machining time by 50%. a small diameter shank and long overhang.

3 3

Note: When face grooving, reduce the speed by 40% in relation to that
used in face turning. The HELI-FACE Solution
The HELI-FACE internal boring bar HFIR/L MC type
with internal coolant can replace the three different
ISO tools and shorten machining time by 20%.

169
 USER GUIDE
FACE GROOVE-TURN

The Multifunction Advantage Insert Replacement

This part was machined using three EDG 33B
different conventional tools.
A standad ISO tool for external turning.

A boring bar for face turning and chamfering.

Eccentric Extractor
Simple to operate; controlled rotation requires low force;
2 guarantees limited upper jaw movement and secures
maximum load on blade.
Two extractor pins are placed in the
two holes in the holder blades.

Indexing
A face grooving tool for grooving,
recessing and chamfering. Place the EDG extractor in the holes
Hold the extractor against the tool.

The HELI-FACE Solution

A single integral HELI-FACE tool HFHPL-M replaces Rotate the eccentric handle to lift the upper jaw.
three ISO tools and reduces machining time by 50%.

170 ISCAR
 USER GUIDE

FACE GROOVE-TURN
Machining Conditions in Face Grooving

Recommended feed range for grooving with Recommended depth of cut and feed range
HFPR/L inserts in various widths. for face turning using HFHR/L toolholders
carrying HFPR/L inserts in various widths.
mm/rev
0.15
0.15 0.15 mm
4.0
0.13
0.12 3.5
0.11

0.1
3.0
0.09
Feed

2.5

Depth of Cut
0.07
2.0
0.05 0.05
0.05
0.04 0.04 1.5
0.03
1.0
0.5
3 4 5 6 mm

Width of Inserts (W)

0.05 0.1 0.15 0.2 0.25 0.3 mm/rev
Feed

Chip shapes for grooving, according to width of

insert and feed, using HFHR/L toolholders. Chip shapes in face turning with inserts HFPR/L-5004
f=0.05 f=0.08 f=0.10 f=0.15 & HFPR/L 6004 and HFHR/L toolholders.
mm/rev mm/rev mm/rev mm/rev f=0.10 f=0.20 f=0.25 f=0.30
mm/rev mm/rev mm/rev mm/rev
W=3, 4 mm

ap=1mm
W=5, 6 mm

ap=2mm

Note: In face grooving, narrowed and deformed chips are preferred.

Curled and long chips can flow out more easily from deep grooves.
ap=3mm
ap=4mm

Note: In roughing, increase feed at small depth of cut and reduce feed at
large depth of cut.

HFPR/L 3003
GRIP/HGPL 300Y

HFPR/L 4004
GRIP/HGPL 400Y
HFPR/L 5004
GRIP/HGPL 500Y
HFPR/L 6004
GRIP/HGPL 600Y

171
 USER GUIDE
FACE GROOVE-TURN

Face Grooving and Turning Recommendations

Using Adapters for 3 mm Inserts Using Adapters for 4-6 mm Inserts

Recommended feed range in grooving with HFPR/L
Recommended feed range for grooving with Grip 3...
inserts and HFAIR/L & HFAER/L adapters.
and HGPL 3... inserts and HGAIR/L and HGAER/L
adapters. Feed range changes according to adapter type. mm/rev
0.12
0.12
mm/rev 0.11
0.08
0.08 0.08 0.10
0.10
0.07

Feed
0.07
0.09

0.06 0.08
Feed

0.07
0.05 0.07
0.05 0.06
0.04 0.05 0.05
0.04 0.05
0.04
0.03 0.04
0.02 0.02 0.02 0.02 0.02
0.02
4 5 6 mm

Width of Inserts (W)

40-60 40-60 40-80 40-80 40-80 m/min
Cutting Speed Vc
Recommended depth of cut and feed range in turning
HGAIR/L 12-3T6 with HFPR/L inserts and HFAIR/L & HFAER/L adapters.
HGAER/L 12-3T6 Feed range changes according to adapter type.
HGAIR/L 14-3T7
mm
HGAER/L 14-3T7 2.5
HGAIR/L 17-3T8
HGAER/L 17-3T8 2.0
HGAIR/L 21-3T9
Depth of Cut ap

HGAER/L 21-3T9 1.5

HGAIR/L 25-3T9
1.0

Recommended depth of cut and feed range for turning 0.5

with HGPL 3... inserts with HGAIR/L and HGAER/L
adapters. Feed range changes according to adapter type. 0.05 0.1 0.15 0.2 0.25 mm/rev
Feed
mm
1.2
HFAIR/L- ...4
HFAER/L- ...4
Depth of Cut ap

1.0
HFAIR/L- ...5
0.8 HFAER/L- ...5

0.6 HFAIR/L- ...6

HFAER/L- ...6
0.4 Note: In roughing, reduce feed when depth of cut is increased, ad increase
feed at small depth of cut.
0.2

0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.11 0.12 mm/rev
Feed

HGAIR/L 21-3T9
HGAER/L 21-3T9
HGAIR/L 25-3T9
HGAIR/L 14-3T7
HGAER/L 14-3T7
HGAIR/L 17-3T8
HGAER/L 17-3T8
HGAIR/L 12-3T6
HGAER/L 12-3T6
Note: In roughing, increase feed at small depth of cut, and reduce feed at
large depth of cut.

172 ISCAR
 USER GUIDE

FACE GROOVE-TURN
Specially Tailored

Semi-Standard Face Grooving

W
and Undercutting Tools
The following drawings show typical semi-standard 3
B
face grooving tools that can be ordered. Please specify T
all relevant dimensions and attach workpiece material
geometric details. D L
T HSK
D IM
4 CAMFIX
T F

W
d
W L
T
B F HSK
1 5
IM
T CAMFIX
W

W L
a B
T
F
2 6
F
B
W

Grade Selection for Facing Applications

ISO P ISO M ISO K ISO N ISO S ISO H
1-11 12-13 14 15-20 21-28 31-37 38-41
Stainless
Steel
Stainless Austenitic
Steel & Duplex High
Ferritic & (Ferritic- Temperature Hard Steel &
Material groups Steel Martensitic Austenitic) Cast Iron Non-ferrous Alloys Cast Iron
Harder IC808 IC808 IC808 IC5010 IC808
IC8250 IC8250 IC8250 IC20 IC20

IC830 IC830 IC908

IC08
FACING
Tougher IC428 IC808
First choice

173
FACE GROOVE-TURN

ALPHABETICAL INDEX
B BHR MB 33

C CGFG 51-P8 88

C#-GHAD-8 142

C#-GHAPR/L-8 143

C#-HAD 144

C#-HAPR/L 144

C#-HATA 142

C#-HFIR/L-MC 145

C#-MAHD 139

C#-MAHD-JHP 140

C#-MAHDOR 139

C#-MAHDR-45 138

C#-MAHPD 141

C#-MAHPD-JHP 141

CR HFIR-M 65-66

C#-TBK-R/L 138

D DGN/DGNC/DGNM-C 79

DGN/DGNM-J/JS/JT 82

DGN-MF 80

DGN-W 81

174 ISCAR
 FACE GROOVE-TURN
G GAFG-R/L-8 87

GDMA 94

GDMF 100

GDMM-CC 108

GDMN 98

GDMU 99

GDMY 95

GDMY-F 97

GDMY (full radius) 96

GFF-N 121

GFF-R/L 121

GFQR 30

GHAPR/L-8 87

GHAR/L-8 86

GHFG-R/L-8 83

GHFGR/L-8 84-85

GHPCOR 28

GIA-K (long pocket) 93

GIF-E (W=8,10) 90

GIF-E (W=8,10 full radius) 92

GIF-E (W=.315,.394) 90

GIF-E (W=.315,.394 full radius) 92

GIFG-E (W=8) 89

175
FACE GROOVE-TURN

G GIFG-E (W=.315) 89

GIF (long pocket) 91

GIMF 101

GIMM 8CC 107

GIMY 102

GIMY-F 103

GIMY (full radius) 104

GIPA/GIDA 8 (full radius) 105

GIPY 106

GRIP 70-71

GRIPA 73

GRIPA (full radius) 74

GRIP (full radius) 72

H HAI-C 60

HAPR/L 52

HAR/L 51

HFAER/L-4 53

HFAER/L-5T, 6T 53

HFAIR/L-4 60

HFAIR/L-DG 61

HFFA 38

HFFH 37

HFFR/L-T 51

176 ISCAR
 FACE GROOVE-TURN
H HFHPR/L-M 55

HFHR/L-3T 40

HFHR/L-4T 41-42

HFHR/L-5T 43-44

HFHR/L-6T 45-46

HFHR/L-M 54

HFIR/L-MC 63-64

HFPAD-3 49

HFPAD-4 49

HFPAD-5 50

HFPAD-6 50

HFPAD-JHP 48

HFPN 67

HFPR/L 68

HFPR/L (full radius) 69

HGAER/L-3 52

HGAIR/L-3 57

HGHR/L-3 39

HGN-C 76

HGN-J 77

HGN-UT 78

HGPL 75

HSK 63 HATA 149

177
FACE GROOVE-TURN

H HSK A63WH-MAHDOR 147

HSK A63WH-MAHDR-45 147

HSK A63WH-MAHUR/L 148

HSK A-WH-TBK-R/L 148

I IH-HFAIR 58

IH-HFPAD 59

IHSR-MIFR 32

IH-TNFPAD 114

IM-GHAD-8 151

IM-HAD 152

IM-HAPR/L 152

IM-HFIR-MC 62

IM-MAHD 150

IM-MAHPD 151

K KIT PICCO Face 28

M MAHPR/L 153

MAHPR/L-JHP 154

MAHPR/L-XL-JHP 155

MAHR/L 156

MAHR/L-JHP 157

MAHR/L-JHP-MC 158

MAHR/L-MG-XL-JHP 159

MAHR/L-MG-XL-JHP-MC 160

178 ISCAR
 FACE GROOVE-TURN
M MEFL 35

MFHR-JHP 32

MGCH-C (face) 29

MIFHR 31

MIFR 34

MINCUT KIT 36

P PCHBR/L 125-126

PCHPR/L 127-128

PCHPRS/LS 130

PCHR/L-34 123

PCHR/L-34-JHP 124

PENTA 34F-R/L 122

PENTA 34F-RS/LS 129

PICCO-010/610 (Face Grooving) 12-13

PICCO-010/610-N (Face Grooving) 10-11

PICCO-010-N (Full Radius for Face Grooving) 14

PICCO-010 (Round Face Groove) 15

PICCO-015 (Face Grooving) 22

PICCO-015-N (Face Grooving) 21

PICCO-016/020 (Face Grooving) 20

PICCO-016/020-N (Face Grooving) 18-19

PICCO-620 (Groove Along Shaft) 17

PICCO-620-N (Face Grooving along Shaft) 16

179
FACE GROOVE-TURN

P PICCO ACE 27

PICCO ACE-N 24

PICCO/MG PCO (Holder) 26

PICCO-N (Holder) 25

PICMU 23

S SGFFA 117-118

SGFFH 119-120

SGFFR/L 115-116

SGTBF 136

SGTBK 135

SGTBU/SGTBN 133-134

T TNFFA-IQ 110

TNFFH-IQ 109

TNF GN-IQ 112

TNF-M-IQ 111

TNFPAD-XL-JHP 113

TNF-P-IQ 111

U UBHCR/L 135

180 ISCAR
ISCAR LTD. Denmark Lithuania South Korea
Israel KJ VAERKTOEJ AS/ISCAR DENMARK MECHA, UAB ISCAR KOREA
Headquarters Tel +45 70 11 22 44 Tel +370 37 407 230 Tel +82 53 760 7594
Tel +972 (0)4 997 0311 Fax +45 46 98 67 10 Fax +370 37 407 231 Fax +82 53 760 7500
Fax +972 (0)4 987 3741 [email protected] [email protected] [email protected]
www.iscar.com www.iscar.dk www.iscarkorea.co.kr
Mexico
[email protected] Ecuador ISCAR DE MÉXICO Spain
Argentina ISCAR Andina Tel +52 (442) 214 5505 ISCAR IBERICA SA
ISCAR TOOLS ARGENTINA SA Tel/fax +57 1 821 93 38 Fax +52 (442) 214 5510 Tel +34 93 594 6484
Tel +54 114 912 2200 [email protected] [email protected] Fax +34 93 582 4458
Fax +54 114 912 4411 [email protected] www.iscar.com.mx [email protected]
[email protected] www.iscar.com.co www.iscarib.es
The Netherlands
www.iscararg.com.ar Estonia ISCAR NEDERLAND B.V. Sweden
Australia KATOMSK AS Tel +31 (0) 182 535523 ISCAR SVERIGE AB
ISCAR AUSTRALIA PTY. LTD Tel +372 6775 671 Fax +31 (0) 182 572777 Tel +46 (0) 18 66 90 60
Tel +61 (0) 2 8848 3500 Fax +372 6720 266 [email protected] Fax +46 (0) 18 122 920
Fax +61 (0) 2 8848 3511 [email protected] www.iscar.nl [email protected]
[email protected] www.iscar.se
Finland New Zealand
www.iscar.com.au ISCAR FINLAND OY ISCAR PACIFIC LTD. Switzerland
Austria Tel +358-(0)9-439 1420 Tel +64 (0) 9 573 1280 ISCAR HARTMETALL AG
ISCAR AUSTRIA GmbH Fax +358-(0)9-466 328 Fax +64 (0) 9 573 0781 Tel +41 (0) 52 728 0850
Tel +43 7252 71200-0 [email protected] [email protected] Fax +41 (0) 52 728 0855
Fax +43 7252 71200-999 www.iscar.fi [email protected]
North Macedonia www.iscar.ch
[email protected] France (Representative Office)
www.iscar.at ISCAR FRANCE SAS Tel +389 2 309 02 52 Taiwan
Belarus Tel +33 (0)1 30 12 92 92 Fax +389 2 309 02 54 ISCAR Taiwan Ltd.
JV ALC “TWING-M” Fax +33 (0)1 30 12 95 82 [email protected] Tel +886 (0)4-24731573
Tel +375 17 506-32-38 [email protected] Fax +886 (0)4-24731530
www.iscar.fr Norway [email protected]
+375 17 506-33-31/65 SVEA MASKINER AS
Tel/Fax +375 17 506-32-37 www.iscar.org.tw
Germany Tel +47 32277750
[email protected] ISCAR Germany GmbH Fax +47 32277751 Thailand
www.twing.by, www.iscar.by Tel +49 (0) 72 43 9908-0 [email protected] ISCAR Thailand Ltd.
Belgium Fax +49 (0) 72 43 9908-93 Tel +66 (2) 7136633-8
[email protected] Peru Fax +66 (2) 7136632
n.v. ISCAR BENELUX s.a. HARTMETALL SAC
Tel +32 (0) 2 464 2020 www.iscar.de [email protected]
Tel: (511) 6612699 www.iscarthailand.com
Fax +32 (0) 2 522 5121 Greece [email protected]
[email protected] INTERNATIONAL TOOLS Turkey
www.iscar.be K.-X. GEORGOPOULOS & SIA O.E Philippines ISCAR Kesici Takim
Tel +30 210 346 0133 MESCO TIC. VE. IML. LTD
Bosnia Tel +63 2631 1775
(Representative Office) Fax +30 210 342 5621 Tel +90 (262) 751 04 84 (Pbx)
[email protected] Fax +63 2635 0276 Fax +90 (262) 751 04 85
Tel +387 32 201 100 [email protected]
Fax +387 32 201 101 [email protected]
[email protected] VIMA Poland www.iscar.com.tr
V. Mazloumian & Sons ISCAR POLAND Sp. z o.o.
Brazil Tel +30 2310 517-117 / 544-521 Ukraine
Tel +48 32 735 7700 ISCAR UKRAINE LLC
ISCAR DO BRASIL COML. LTDA. Fax +30 2310 529-107 Fax +48 32 735 7701
Tel +55 19 3826-7100 [email protected] Tel +38 (050) 440 23 91
[email protected] [email protected]
Fax +55 19 3826-7171 http://www.vimaco.gr www.iscar.pl
DDG 0800 701 8877 www.iscar.com.ua
[email protected] Hong Kong Portugal
www.iscar.com.br MTC TOOLING SYSTEMS LTD ISCAR Portugal, SA United Arab Emirates
Tel +85-2-23054838 Tel +351 256 579950 SVRS General Trading LLC
Bulgaria Fax +85-2-27988789 Fax +351 256 586764 Tel +971 4 342 6699
ISCAR BULGARIA [email protected] [email protected] www.svrs-mena.com
Tel/Fax +359 431 62557 www.iscarportugal.pt
[email protected] Hungary United Kingdom
www.iscar.bg ISCAR HUNGARY KFT. Romania ISCAR TOOLS LTD.
Tel +36 28 887 700 ISCAR Tools SRL Tel +44 (0) 121 422 8585
Canada Fax +36 28 887 710 Tel +40 (0)312 286 614 Fax +44 (0) 121 423 2789
ISCAR TOOLS INC. [email protected] Fax +40 (0)312 286 615 [email protected]
Tel +1 905 829 9000 www.iscar.hu [email protected] www.iscar.co.uk
Fax +1 905 829 9100
[email protected] India Russia United States
www.iscar.ca ISCAR India Ltd. Moscow ISCAR METALS INC.
Tel +91 77009 63707 ISCAR LLC Tel +1 817 258 3200
Chile [email protected] Tel/fax +7 495 660 91 25/31 Tech Tel 1-877-BY-ISCAR
J&A INTERNATIONAL www.iscar.in [email protected] Fax +1 817 258 3221
Tel +56 2 2232 5838 www.iscar.ru [email protected]
[email protected] Indonesia
www.iscarmetals.com
www.jya.cl CV MULTI TEKNIK Serbia
Tel +62-21-29206242/44/45/59 ISCAR TOOLS d.o.o. Venezuela
China Fax +62-21-29206243 Tel +381 11 314 90 38 FERREINDUSTRIAL ISO-DIN C.A.
ISCAR CHINA [email protected] Fax +381 11 314 91 47 Tel +58 2 632 8211/633 4657
Tel +86 21 8024 8888 [email protected] Fax +58 2 632 5277
[email protected] Ireland
[email protected]
www.iscar.com.cn HARD METAL MACHINE TOOLS Singapore
Tel +353 (0) 1 286 2466 SINO TOOLING SYSTEM Vietnam
Colombia Fax +353 (0) 1 286 1514 Tel +65 6566 7668 ISCAR VIETNAM
ISCAR Andina [email protected] Fax +65 6567 7336 (Representative Office)
Tel +57 310 380 9932 www.hardmetal.ie [email protected] Tel +84 8 38 123 519/20
Tel/fax +57 1 896 65 78 Fax +84 8 38 123 521
[email protected] Italy Slovakia [email protected]
www.iscar.com.co ISCAR ITALIA srl ISCAR SR, s.r.o. www.iscarvn.com
Tel +39 02 93 528 1 Tel +421 (0) 41 5074301
Croatia Fax +39 02 93 528 213 Fax +421 (0) 41 5074311
“© 2013 Iscar Ltd. This document, as well as all information
and other data contained herein and/or derived therefrom,
ISCAR ALATI d.o.o. [email protected] [email protected] including but not limited to, all trademarks, logos, trade-
Tel +385 (0) 1 33 23 301 www.iscaritalia.it www.iscar.sk names, concepts, pictures, designs and/or devices, as well
Fax +385 (0) 1 33 76 145 as any data from which any proprietary and/or intellectual
[email protected] Japan Slovenia property right may emanate (“Information”), is the sole
and exclusive property of Iscar Ltd. and is protected
www.iscar.hr ISCAR JAPAN LTD. ISCAR SLOVENIJA d.o.o. by copyright and other applicable laws. No part of any
Tel +81 6 6835 5471 Tel +386 1 580 92 30 Information may be used or otherwise disseminated for any
Cyprus Fax +81 6 6835 5472 Fax +386 1 562 21 84 purpose whatsoever without the express prior
WAMET (Demetriades) Ltd. written consent of Iscar Ltd.
[email protected] [email protected] Items appearing in this catalog may be improved, amended
Tel +357 (0) 2 336660/5498 www.iscar.co.jp www.iscar.si or withdrawn without prior notice.”
Fax +357 (0) 2 333386
Latvia Please check ISCAR’s online catalog
[email protected] South Africa www.iscar.com for the most current
MECHA, UAB ISCAR SOUTH AFRICA (PTY) LTD.
Czech Republic Tel +370 37 407 230 technical information regarding
ShareCall 08600-47227 our products.
ISCAR CR s.r.o. Fax +370 37 407 231 Tel +27 11 997 2700
Tel +420 377 420 625 [email protected] Fax +27 11 388 9750 2022
Fax +420 377 420 630 [email protected]
[email protected] www.iscar.co.za
www.iscar.cz
G
 TIFIED QM TIFIED QM TIFIED EM D OHS SY GYMANAGEM
ER ER ER FIE ER
C

CERTIFIEDEN
I
C

CERT

STE

ENT
S

SI SI SI SI
SYSTEM

ISO
M

AS 9100 ISO 9001: ISO 14001: ISO

2015 2015 45001:2018 50001

THE STANDARDS INSTITUTION OF ISRAEL THE STANDARDS INSTITUTION OF ISRAEL THE STANDARDS INSTITUTION OF ISRAEL THE STANDARDS INSTITUTION OF ISRAEL THE STANDARDS INSTITUTION OF ISRAEL

Quality Standard
ISCAR has been certified by the prestigious Standards Institution,
as being in full compliance to ensure delivery of the finest quality
goods. Quality control facilities include the metallurgical laboratory,
raw metal testing, an online testing procedure and a machining
center for tool performance testing and final product inspection.
Only the finest products are packaged for entry into
ISCAR’s inventory.
ISCAR FACE GROOVINGLINES
Metric and Inch Catalog

Download ISCAR WORLD APP E-CAT

w w w . i s c a r. c o m