Scribd
Upload
232 views2 pages

EEC Fault Codes

The document provides fault codes for the RB211-535E4 engine electronic control equipment, bleed valve control unit, and turbine protection unit. It lists specific fault codes and their corresponding systems and issues.

Uploaded by

przytul2007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
232 views2 pages

EEC Fault Codes

The document provides fault codes for the RB211-535E4 engine electronic control equipment, bleed valve control unit, and turbine protection unit. It lists specific fault codes and their corresponding systems and issues.

Uploaded by

przytul2007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

“For Reference Only”

RB211-535E4 - EEC Fault Codes


Code System Input

02 Ground Test Switch “ON” with Engine Running


1A Short Duration Intermittent N1 Fault
14 N1 Major signal Fault or Circuit Fault
21 EGT Signal Major Open Circuit Fault
24 EGT Signal Rate or Range Fault
2A Short Duration Intermittent EGT Fault Due to Rate or Range
2B Short Duration Intermittent EGT Fault Due to Open Circuit
31 FFG Torque Motor Coil 1 or 2 Open Circuit
34 LVDT Range Fault
35 LVDT / Torque Motor Fault Detected During Power Up
39 Fail Fix Solenoid Fault
40 EPR and P1 Signal Failure
43 EPR or P1 Signal Failure
44 EPR and/or P1 Signal Rate or Range Fault
47 P1 from EPR Transmitter, Failed Cross Check with P1 from L & R ADC’s
4A Short Duration Intermittent EPR and P1 Fault
54 TLA Transducer Output Incorrect
5A Short Duration Intermittent TLA Output Fault
60 Left ADC Signal Lost (All Parameters)
61 Left ADC Signal Fault (One or More Parameters)
64 Left ADC Range Fault (One or More Parameters)
66 Left ADC Altitude Fault
67 P1 From Left ADC Has Failed Cross Check
68 T1 From Left ADC Has Failed Cross Check
70 Right ADC Signal Lost (All Parameters)
71 Right ADC Signal Fault (One or More Parameters)
74 Right ADC Range Fault (One or More Parameters)
76 Right ADC Altitude Fault
77 P1 From Right ADC Has Failed Cross Check
78 T1 From Right ADC Has Failed Cross Check
94 T2 Range Error
96 T1E Has Failed Cross Check With T1 From L and R ADC’s
D6 Altitude From L & R ADC’s Differ By More than 252 Feet
D7 P1 Cross Check Error – Between L and R ADC’s
D8 P1 Cross Check Error – Between L and R ADC’s
B3 FFG Not Following EEC Instructions (May be EEC or FFG Fault)
B* Any other B Code, Replace EEC
“For Reference Only”

RB211-535E4 - BVCU & TPU Fault Codes


BVCU LEVEL SYSTEM INPUT

01 M ALTITUDE SWITCH FAULT


02 M N2 NO. 1 SPEED PROBE FAULT
03 M N2 NO. 2 SPEED PROBE FAULT
04 M PLA TRANSDUCER SIGNAL FAILED
05 M T2 THERMOCOUPLE SIGNAL FAULT
06 M DGCU “A” FAULT (UPPER)
07 M DGCU “B” FAULT (LOWER)
10 M HP3 SOLENOID (LOWER) COIL “A” OR “B” FAULT
11 M HP3 SOLENOID (UPPER) COIL “A” OR “B” FAULT
12 M IP6 SOLENOID (RIGHT) COIL “A” OR “B” FAULT
13 M IP6 SOLENOID (RIGHT) COIL “A” OR “B” FAULT
16 M PLA TRANSDUCER INCORRECTLY SET
18 M HP2 SOLENOID COIL “A” FAULT
19 M HP2 SOLENOID COIL “A” FAULT
91 M DDU CHANNEL 1 FAULT. CHANNEL INOPERATIVE
92 M DDU CHANNEL 2 FAULT. CHANNEL INOPERATIVE
BB M BVCU INTERNAL FAULT

TPU LEVEL M = MAINTENANCE Level Messages

10 M P4 TRANSDUCER OR PROCESS FAULT


20 M DGCU A OR B, OR GROUND TEST SWITCH FAULT
30 M TFU SOLENOID OR WIRING FAULT
40 M SURGE DETECTED OR P4 TRANSDUCER FAULT
50 M INTERNAL UNIT FAULT – ASSOCIATED WITH IGNITION
60 M PLA TRANSDUCER OR WIRING FAULT
90 M EICAS MAINTENANCE LINE FAULT, GROUNDED BY BVCU OR
SYSTEM DEPOWERED (DUE TO BVCU CODES BEING PRESENT)
B* M INTERNAL TPU FAULT

THIS DOCUMENT IS FOR REFERENCE ONLY.


REFERENCE MUST BE MADE TO THE OFFICIAL PUBLICATIONS AND MANUALS FOR
ENGINE OPERATION AND MAINTENANCE.

You might also like