Industry Portfolio Catalogue Vietnam en 50Hz

Vietnam
English
50Hz
GRUNDFOS
SOLUTIONS
For Industry
WATER TREATMENT
Water Intake / Water Treatment Wastewater

Supply / Transfer Treatment & Reuse
TEMPERATURE CONTROL
Industrial Heating Industrial Cooling
INDUSTRIAL PROCESSES
Machining Cleaning Processes Process Fluid

Transfer
Grundfos delivers a range of products,

Grundfos delivers a range of products,
solutions and services to help maintain
industrial processes. Grundfos pumps are
built to withstand aggressive media and the
demands of industry. This portfolio overview
presents these as well as dosing and
disinfection, monitors, controls and sensors,
service offerings and digital solutions
available for all applications before, after
and related to industrial processes.
The products shown are suitable for the majority of applications. There could be
exceptions where other products of our broad portfolio fit better. Please ask your local
sales representative. The product specifications show the maximum ranges and can vary
in your local country. Please have a look in Grundfos Product Center for detailed data.
7 SERVICE OFFERINGS
8 PRODUCTS
8 Water Intake / Supply / Transfer

9 Ground water intake
11 Surface water intake
14 Seawater intake
16 Supply & Transfer
18 Water Treatment
19 Chemical Treatment
22 Physical Treatment
26 Disinfection
28 Sea Water Desalination
33 Wastewater Treatment & Reuse

34 Wastewater transfer
37 Chemical Treatment
40 Biological Treatment
43 Physical Treatment
47 Disinfection
49 Industrial Heating
50 Boiler System
54 Heat Distribution
56 Industrial Cooling
57 Cooling Tower
60 Chiller/Evaporator/Condenser/Cooling Water Distribution
63 Machining
64 Clean Side
67 Dirty Side
69 Cleaning Processes
70 Food
73 Non Food
77 Process Fluid Transfer

78 Process Fluid Transfer
82 PROCESS CHARTS
Service & Solutions
By taking a greater responsibility for the

operation and efficiency of your pumps, we
allow you to focus your attention on what is
important to you rather than worrying about
your pumps.
We bring peace of mind to you by

minimisingdowntime, optimising performance
and helping you contribute to a more
sustainable world.
We add value through:
Enhanced asset management

Energy and water savings
Digital services
Service Agreements Repair Services Operation Services Optimisation Services
Grundfos Energy Earnings Spare Parts Installation Energy Check Advanced
All-In-Maintenance Repair Extended Warranty Energy Check Basic
Customized Service Agreement Laser Alignment
Standard Service Agreement Inspection
Commissioning
4
Optimisation Services
Energy Check Advanced identifies opportunities for energy The Energy Check Advanced includes:
optimisation within your processes based on measured data. •Site visit to gather data from your pumping system
•Load profiles from measurement of power consumption
Energy Check The energy check advanced report provides fully costed •Energy Check Advanced report
Advanced recommendations for process optimisation and energy savings. •Presentation of the final report and potential savings
The Energy Check Advanced report provides recommendations for
replacement pumps correctly sized to the application with reduced
energy consumption
Energy Check identifies opportunities for improvement of The energy check process includes:
energy efficiency in your system based on pump nameplate • Site visit to gather data from your pumping system
specifications. • Load profiles by measurement of power consumption (Energy Check
Energy Check The energy check report provides recommendations for Advanced)
Basic replacement pumps with the same specifications but lower • Energy check report
energy consumption. • Presentation of final report
The energy check report provides recommendations for replacement
pumps with the same specifications but lower energy consumption.
Repair Services
With Grundfos original spare parts, you get more than just spare • Increased efficiency
parts. You get the right spare part solutions and service kits with • Greater reliability / minimised downtime
these benefits: • Documented performance
Spare Parts • Fast delivery
Downtime is inconvenient and expensive so to minimise this, we Workshop repair: Workshop repairs are the ideal choice for smaller
offer two types of repair service: on-site and workshop repair. pumps that can be shipped easily.
On-site repair: Having our service technician come to you to do on-site
Repair repair is the best option for large installed pumping systems.
Service Agreements
Grundfos Energy Earnings allows you to finance your pumps with Benefits include:
a share of your energy earnings. With Grundfos Energy Earnings, • No initial equipment costs
OPEX savings are guaranteed and no CAPEX investments are • Guaranteed energy savings
Grundfos Energy required. Simply put, your energy earnings finance your new • Contribute toward sustainability goals
Earnings pump systems. • All-inclusive maintenance with a peace of mind operation
Broken pumps and stalled productions result in huge costs. Benefits:

Grundfos All-in-Maintenance is a complete maintenance • Maximised reliability and efficiency
solution allowing you to focus on your business, while we • Preventive maintenance
All-In-Maintenance manage the service and maintenance of your assets at a fixed • Fixed maintenance costs
price. All-in-Maintenance is designed to maximise your peace of • Customise your spare parts inventory
mind at no extra cost. • Less administrative work
A Customised Service Agreement is tailor-made to suit your Choose elements across:

needs. Pick and mix from our extensive service offering and pay • Repair services
only for what you need. • Operation services
Customized The customisable service agreement gives you direct access to • Optimisation services
Service Grundfos professionals and our trusted partners for the selected
Agreement service offerings.
A Standard Service Agreement consists of one or two yearly The check includes:
inspections by a qualified service technician. • Equipment check
The service technician checks your equipment, assesses the need • Inspection report covering pumps, motors, wear partsand integrated
Standard Service for repair and/or preventive maintenance. controls
Agreement • Recommendations for performance optimisation, if required
5
Operation Services
We offer Installation by a skilled service technician to ensure Installation includes:

correct installation according to I&O manual. • Delivery to your facility
This will ensure that your Grundfos pump achieves optimal • Installation and mounting on the correct type of base
Installation performance. • Mechanical work, incl. alignment of pipes and flanges
• Electrical installation
• System start-up
How you benefit from our Extended Warranty See how the Grundfos Extended Warranty works for you!
• Peace of mind: up to 5 years of warranty • 12, 24 or 36 months of additional warranty coverage
• Easy overview: clearly defined warranty terms and conditions • Insurance against defects in materials or workmanship
Extended throughout warranty period • Same terms and conditions as standard warranty
Warranty • Fast response: well-defined contacts and short response time in • Well-defined contacts and short response time in case of warranty
case of warranty claims claims
• Can be purchased with pump or along with Service Contract
Alignment between pump and motor can cause unnecessary Benefits:

wear and damage other parts of the system. • Prolonged lifetime, less wear and tear
To significantly reduce these risks, we offer Laser Alignment to • Lower noise level
Laser Alignment ensure 100% accuracy. • Lower lifecycle costs
Your whole system is analysed according to a specific checklist by Benefits:

expert personnel. • Reduce energy consumption
This gives you an overview of any adjustments or spare part • Reduce operating costs
Inspection replacements necessary to improve your system and provide • Prolong lifetime
financial benefits. • Pumps run at peak performance
Expert service technicians verify that the installation is Benefits:

consistent with I&O manual, and that everything is set up • Grundfos-approved installation
correctly. • Reduced operation costs
Commissioning This will ensure that your pumping system is running as • Eliminated wear on pumps
efficiently as possible. • Prolonged lifetime
6
Service offerings
Service agreements and offerings covering operation, repair and optimisation as well as digital
offerings are shown for the equipment categories relevant for the specific application.
Submersible Submersible
Multistage Single-stage Circulator Disinfection
Groundwater Wastewater Hydro Boosters Dosing Pumps
Pumps Pumps Pumps Systems
Pumps Pumps
Optimisation Services
Energy Check
Advanced
Energy Check Basic
Repair Services
Spare Parts
Repair
Service Agreements
Grundfos Energy
Earnings
All-In-Maintenance
Customized
Service Agreement
Standard Service
Agreement
Operation Services
Installation
Extended
Warranty
Laser Alignment
Inspection
Commissioning
Available Special conditions and limitations
7
Water Intake / Supply /
Transfer
A production plant needs water to operate. Grundfos offers a complete portfolio of pumps to
reliably supply water to the plant; the right amount, at the right pressure and at the right time.
Whether the source is a well, mains or a river or lake, and no matter the quality of the water,
Grundfos has efficient and high-quality equipment that supplies and transfers the water as
needed, with no surprises.
"Not only have we seen an immediately improved water supply

with stable and constant pressure; we have been able to monitor
and trend the flows, enabling continuous improvements on our
processes."
Calvin Winch, Engineer,

Operations Development
GB & I, Britvic Soft Drinks
Ltd
GROUND WATER INTAKE
Pumps
Submersible groundwater pumps - SP Submersible groundwater pumps - SQ/SQE
Grundfos SP are submersible borehole pumps, designed for SQ/SQE pumps are compact submersible pumps, designed
pumping groundwater. Grundfos SP are all stainless-steel for domestic groundwater supply for private housing, small
pumps, and they are available in 3 material grades. The waterworks, and small irrigation systems.
pumps are suitable for boreholes in sizes ranging from 4"
over 6" and 8" to 10".
Flow max.: 290 m³/h Head max.: 676 m Flow max.: 9 m³/h Head max.: 230 m
Liquid temperature: -15..90 °C p max.: 60 bar Liquid temperature: 0..35 °C p max.: 15 bar
Monitors, Controls and Sensors

Communication Interfaces - CIM/CIU Motor Protection - MP 204
Communication Interface Module/Communication MP 204 protects the motor against overload, dry running
Interface Unit is the range of communication options from and incipient motor defects based on many parameters like:
Grundfos. They enable you to connect your product to the supply voltage, phase sequence or harmonic distortion. It
wide range of field bus standards. disconnects the contactor if, for example, the current
exceeds the preset value. It can be used stand-alone or for
example incorporated in a Control DC.
Motor Protection - Control MP 204 Pump control - Control CUE

Pump controller system designed for water utility market. Grundfos Control CUE is a series of external frequency
Complete protection of one pump. converters designed for speed control of a wide range of
Grundfos pumps. The Frequency converter is delivered
installed in a cabinet with main switch, circuit breaker, and
an optional filter. Power range: 2.2 kW - 90 kW.
Pump control - CU 200, 300, 301 Pump control - Control MPC

The control units are designed for communication,
monitoring and control of submersible pumps. The CU 200 Control MPC controls up to six identical pumps connected
is suitable for the SQFlex system, it also enables the in parallel. It uses advanced algorithms to optimise
connection of a level switch. The CU 300 is suitable for SQE performance and minimise energy consumption
submersible pumps in various applications, the CU 301 for
SQE in constant pressure applications.
Level Control - LC 232 / LC 242 Level Transmitters - MS1, M2, FS1

Float switches for level control/monitoring in tanks,
LC 232 / LC 242 level controllers offer a comprehensive range pumping stations or similar applications.
of features for groundwater installation, monitoring and
control of one or two pumps.
9
GROUND WATER INTAKE
Level Transmitters - Level Transmitter S, E, W Flow Sensors - VFI/VFS

Hydrostatic level transmitters with different versions. S: Flow and temperature sensors designed to be robust and
applicable for most wastewater, drinking water and other accurate. They use our Silicoat® coating to be in direct
media usages, W: wastewater, E: endurance and robustness contact with the media and provide stable signals.
strengthened product.
Liquid temperature: -30..120 °C
Flow Sensors - MAG 3100, 5100, 8000 Pressure Sensors - DPI, DPS, RPI, RPS
Several variants of the Mag Flow system are available, Our pressure sensor ranges are designed to be robust,
depending on needed requirements and specifications. In accurate and reliable. Depending on the product family they
general, the system consists of a flow meter and a measure relative or differential pressure and temperature.
transmitter of choice. MAG 3100 covers all the applications They use our Silicoat coating to be in direct contact with the
which the other industry specific sensors do not cover. media and provide stable signals.
M&C for Dosing & Disinfection - DID M&C for Dosing & Disinfection - DIT-L, DIT-M
The DID system with bypass flow cell is intended for Photometers for several parameters (e.g. chlorine, ClO2, O3,
monitoring and control of disinfectants, pH, ORP, pH), with two different wavelengths, with high-quality
conductivity and temperature. The system is preassembled interference filters and long-term stable LEDs as light
on a common backplate and includes a control unit CU382 source, without moving parts, automatic selection of the
as well as the water parameter sensor(s). Several wavelength, easy operation.
accessories are available.
p max.: 3 bar
Drives
External Frequency Converters - CUE
CUE is a complete range of external frequency converters
designed for speed control of a wide range of Grundfos
pumps. CUE has a built-in PI controller and offers the same
functionality and user-interface as Grundfos E-pumps.
Power range up to 250 kW.
10
SURFACE WATER INTAKE
The Hydro MPC optimises the energy consumption by determining the most efficient speed and required number of pumps.
Pumps
Vertical multistage pumps - CR/CRE Endsuction close coupled single-stage pumps - NB/NBE
End-suction close-coupled pumps according to EN 733. The
Vertical, multistage centrifugal pump with suction and pump has an axial suction port, radial discharge port,
discharge ports on the same level. horizontal shaft and a back pull-out design enabling
removal of the motor, motor stool, cover and impeller
without disturbing the pump housing or pipework.
Liquid temperature: -40..150 °C p max.: 40 bar Liquid temperature: -25..120 °C p max.: 16 bar
Endsuction long coupled single-stage pumps - NK/NKE Horizontal splitcase pumps - LS

Standard pumps according to EN 733. The pump has an Grundfos LS is a horizontal, single-stage or double-stages,
axial suction port, a radial discharge port and horizontal between bearings, split case pump. The axially split design
shaft. It is of the back pull-out design enabling removal of allows easy removal of the top casing and access to the
the coupling, bearing bracket and impeller without pump components without disturbing the motor or pipe
disturbing the motor, pump housing or pipework. work.
Flow max.: 1401 l/s Head max.: 177 m Flow max.: 9503 m³/h Head max.: 238 m
Service offerings
All-In-Maintenance Customized Service Agreement
Laser Alignment Commissioning


11
Pump control - CU 200, 300, 301 Pump control - Control MPC

The control units are designed for communication,
monitoring and control of submersible pumps. The CU 200 Control MPC controls up to six identical pumps connected
is suitable for the SQFlex system, it also enables the in parallel. It uses advanced algorithms to optimise
connection of a level switch. The CU 300 is suitable for SQE performance and minimise energy consumption
submersible pumps in various applications, the CU 301 for
SQE in constant pressure applications.


Flow Sensors - MAG 3100, 5100, 8000 Pressure Sensors - DPI, DPS, RPI, RPS
Several variants of the Mag Flow system are available, Our pressure sensor ranges are designed to be robust,
depending on needed requirements and specifications. In accurate and reliable. Depending on the product family they
general, the system consists of a flow meter and a measure relative or differential pressure and temperature.
transmitter of choice. MAG 3100 covers all the applications They use our Silicoat coating to be in direct contact with the
which the other industry specific sensors do not cover. media and provide stable signals.
M&C for Dosing & Disinfection - DID M&C for Dosing & Disinfection - DIT-L, DIT-M
The DID system with bypass flow cell is intended for Photometers for several parameters (e.g. chlorine, ClO2, O3,
monitoring and control of disinfectants, pH, ORP, pH), with two different wavelengths, with high-quality
conductivity and temperature. The system is preassembled interference filters and long-term stable LEDs as light
on a common backplate and includes a control unit CU382 source, without moving parts, automatic selection of the
as well as the water parameter sensor(s). Several wavelength, easy operation.
p max.: 3 bar
12
Drives
Service offerings
13
SEAWATER INTAKE
Pumps
Endsuction close coupled single-stage pumps - NBG/NBGE Endsuction close coupled single-stage pumps - NB/NBE
Close-coupled pumps according to ISO 2858. Flanges are PN End-suction close-coupled pumps according to EN 733. The
16 with dimensions according to AS2129 table E. The pump pump has an axial suction port, radial discharge port,
has an axial suction port, radial discharge port, horizontal horizontal shaft and a back pull-out design enabling
shaft and a back pull-out design enabling removal of the removal of the motor, motor stool, cover and impeller
motor, motor stool, cover and impeller without disturbing without disturbing the pump housing or pipework.
the pump housing or pipework.
Endsuction long coupled single-stage pumps - NK/NKE Submersible groundwater pumps - SP

Standard pumps according to EN 733. The pump has an Grundfos SP are submersible borehole pumps, designed for
axial suction port, a radial discharge port and horizontal pumping groundwater. Grundfos SP are all stainless-steel
shaft. It is of the back pull-out design enabling removal of pumps, and they are available in 3 material grades. The
the coupling, bearing bracket and impeller without pumps are suitable for boreholes in sizes ranging from 4"
disturbing the motor, pump housing or pipework. over 6" and 8" to 10".
Customised Solutions - Custom-Built Pumps
Customised pumps to meet specific application challenges

(temperatures, pressures, difficult liquids) or installation
requirements (ambient conditions) not covered by the
standard pump range. It is a modular platform built on
stocked components. For more information please contact
Grundfos sales.
14
SEAWATER INTAKE

Level Transmitters - Level Transmitter S, E, W Pressure Sensors - DPI, DPS, RPI, RPS
Hydrostatic level transmitters with different versions. S: Our pressure sensor ranges are designed to be robust,
applicable for most wastewater, drinking water and other accurate and reliable. Depending on the product family they
media usages, W: wastewater, E: endurance and robustness measure relative or differential pressure and temperature.
strengthened product. They use our Silicoat coating to be in direct contact with the
media and provide stable signals.
M&C for Dosing & Disinfection - DID

The DID system with bypass flow cell is intended for
monitoring and control of disinfectants, pH, ORP,
conductivity and temperature. The system is preassembled
on a common backplate and includes a control unit CU382
as well as the water parameter sensor(s). Several
p max.: 3 bar
15
SUPPLY & TRANSFER
Hydro MPC E and Multi E help meet energy targets and are ready for future growth as it can deliver min and max flows
keeping a high efficiency in mind. Additionally, the system can be delivered with a standby pump that can be easily used as
a duty pump and by that extend the flow significantly.
Pumps
Vertical multistage pumps - CR/CRE Endsuction close coupled single-stage pumps - NB/NBE
End-suction close-coupled pumps according to EN 733. The
Vertical, multistage centrifugal pump with suction and pump has an axial suction port, radial discharge port,
discharge ports on the same level. horizontal shaft and a back pull-out design enabling
removal of the motor, motor stool, cover and impeller
Endsuction long coupled single-stage pumps - NK/NKE Horizontal splitcase pumps - LS

Standard pumps according to EN 733. The pump has an Grundfos LS is a horizontal, single-stage or double-stages,
axial suction port, a radial discharge port and horizontal between bearings, split case pump. The axially split design
shaft. It is of the back pull-out design enabling removal of allows easy removal of the top casing and access to the
the coupling, bearing bracket and impeller without pump components without disturbing the motor or pipe
disturbing the motor, pump housing or pipework. work.


16
SUPPLY & TRANSFER
Pump control - Control MPC Level Control - LC 232 / LC 242
Control MPC controls up to six identical pumps connected LC 232 / LC 242 level controllers offer a comprehensive range
in parallel. It uses advanced algorithms to optimise of features for groundwater installation, monitoring and
performance and minimise energy consumption control of one or two pumps.
Level Transmitters - MS1, M2, FS1 Level Transmitters - Level Transmitter S, E, W

Float switches for level control/monitoring in tanks, Hydrostatic level transmitters with different versions. S:
pumping stations or similar applications. applicable for most wastewater, drinking water and other
media usages, W: wastewater, E: endurance and robustness
Pressure Sensors - DPI, DPS, RPI, RPS M&C for Dosing & Disinfection - DID
Our pressure sensor ranges are designed to be robust, The DID system with bypass flow cell is intended for
accurate and reliable. Depending on the product family they monitoring and control of disinfectants, pH, ORP,
measure relative or differential pressure and temperature. conductivity and temperature. The system is preassembled
They use our Silicoat coating to be in direct contact with the on a common backplate and includes a control unit CU382
media and provide stable signals. as well as the water parameter sensor(s). Several
Liquid temperature: -30..120 °C p max.: 3 bar
Drives
Systems
Booster Systems - Hydro MPC, Hydro Multi-E
Advanced and energy efficient pressure boosting system for
boosting of clean water. Available with 2 - 6 (2 - 4 for
Multi-E) parallel connected pumps, integrated advanced
controller and all necessary fittings.
Flow max.: 1464 m³/h Head max.: 161 m

Liquid temperature: 0..60 °C p max.: 16 bar
17
Water Treatment
Grundfos has an extensive range of water treatment pumps and solutions for the entire water
treatment cycle from intake and distribution to handling of wastewater. Water treatment is
technology-driven and heavily regulated, and pump, dosing and disinfection solutions have been
designed to meet every demand and comply with regulations. Grundfos has years of water
treatment application experience and guarantees the perfect match between component and
sub-system, whether you are looking for packaged solutions or individual pumping products for
each stage of the treatment process.
"Our small reverse osmosis 1000 lit./h system with activated

carbon and softener for pretreatment. Thanks to Grundfos 'smart'
pump we are controlling RO only with pump, there is no
additional controller or PLC needed."
Vladimir Kruljac, CEO FELLER

d.o.o.
CHEMICAL TREATMENT
Bubble formation due to outgassing chemicals like sodium hypochlorite could lead to inefficient and unreliable processes.
With FLOW CONTROL in DDA dosing pumps this can be eliminated.
Measurement of pulsating flows can be challenging for conventional flow meters. With FCM this functionality is integrated
in DDA dosing pumps simplifying the installation with less components.
All relevant approvals, certifications and documentation is included in our prefabricated dosing skid systems ready to
install.
Pumps
Digital Dosing Pumps - SMART Digital S/XL Mechanical Dosing Pumps - DMX
With their robust diaphragm-based design and their
SMART Digital diaphragm dosing pump with powerful high-quality motors, DMX pumps require minimum
variable-speed stepper motor (S) or powerful PMS maintenance and are the best choice for many dosing
(Permanent Magnet Synchronous) motor (XL) and applications. The DMX range is highly versatile: it covers a
FlowControl system to automatically detect malfunctions. wide flow range and offers a variety of dosing head sizes,
High-end solution for complex and demanding applications materials and accessories.
with turn-down ratio up to 1:3000.
Flow max.: 200 l/h Flow max.: 4000 l/h

Mechanical Dosing Pumps - DMH Customised Solutions - Custom-Built Pumps
The DMH range is a series of extremely strong, robust Customised pumps to meet specific application challenges
hydraulically actuated piston diaphragm dosing pumps for (temperatures, pressures, difficult liquids) or installation
applications requiring reliable dosing and high-pressure requirements (ambient conditions) not covered by the
capability, such as process engineering. The range is highly standard pump range. It is a modular platform built on
versatile: it covers a wide flow range and offers a variety of stocked components. For more information please contact
dosing head sizes, materials and accessories. Grundfos sales.
Flow max.: 3000 l/h

Service offerings
Commissioning

Motor Protection - MP 204 Motor Protection - Control MP 204
MP 204 protects the motor against overload, dry running Pump controller system designed for water utility market.
and incipient motor defects based on many parameters like: Complete protection of one pump.
supply voltage, phase sequence or harmonic distortion. It
disconnects the contactor if, for example, the current
19
CHEMICAL TREATMENT
Level Transmitters - Level Transmitter S, E, W M&C for Dosing & Disinfection - DID
Hydrostatic level transmitters with different versions. S: The DID system with bypass flow cell is intended for
applicable for most wastewater, drinking water and other monitoring and control of disinfectants, pH, ORP,
media usages, W: wastewater, E: endurance and robustness conductivity and temperature. The system is preassembled
strengthened product. on a common backplate and includes a control unit CU382
p max.: 3 bar
Communication Interfaces - E-Box M&C for Dosing & Disinfection - DIT-L, DIT-M
The E-Box device enables our digital dosing pumps SMART Photometers for several parameters (e.g. chlorine, ClO2, O3,
Digital S to communicate with a wired transmission to a pH), with two different wavelengths, with high-quality
various range of fieldbus standards. interference filters and long-term stable LEDs as light
source, without moving parts, automatic selection of the
wavelength, easy operation.
Systems
Dosing Skid Systems - DSS Dosing Tank Stations - DTS
Dosing skid systems range from pre-engineered, standard Dosing tank stations are intended for storing and dosing
one, two and three pump systems, to custom systems with liquids. Many different configurations can be selected
multiple pumps and tanks all piped on a common skid flexibly to fulfil various dosing tasks. They are available in 6
complete with controls. tank sizes: 60 l, 100 l, 200 l, 300 l, 500 l and 1000 l.
Disinfection Systems
Chlorine Dioxide Systems - Oxiperm Pro Chlorine Dioxide Systems - Oxiperm 166
Compact pre-mounted chlorine dioxide preparation and Compact pre-mounted chlorine dioxide preparation system.
dosing system. Oxiperm Pro generates a ClO2 solution from Oxiperm 166 uses concentrated NaClO2, chlorine gas and
diluted NaClO2, HCl and water and supports flow water to produce a ClO2 solution which is stored in the
proportional or setpoint controlled dosing. Accessories for included batchtank. The product range covers all equipment
installation and measurement of ClO2 content are part of needed between chemical containers and injection point to
the product range. Max. ClO2 prep. quantity: 60 g/h the process. Max. ClO2 prep. quantity: 10 kg/h
Electro-chlorination Systems - Selcoperm Chlorine Gas Systems - Vaccuperm

The Vaccuperm range is our vacuum chlorine gas dosing
SES electrolysis systems produce sodium hypochlorite equipment covering all equipment between the chlorine
solution from common salt and water using electricity. The gas container and the water line to be treatedas well as
accessories range provides the complete installation from chlorine container handling and safety equipment. The
brine preparation to the injection point. A max. production different lines cover a max. chlorine flow of up to 4 kg/h
capacity of up to 1,8 kg/h (SES 125-2000) and 45 kg/h (SES (VGB 103, VGA 113), 20 kg/h (VGA 117) and 200 kg/h (VGS).
5000-45000) chlorine equivalent is covered.
Liquid temperature: 0..20 °C
20
CHEMICAL TREATMENT
Service offerings
Commissioning
Accessories
Dosing Pump Accessories - General and Tank Accessories
Comprehensive range of accessories for safe operation
covering every requirement when dosing with Grundfos
pumps. The range includes: installation kits, tanks, mixers,
suction lances, tubing, adaptors, connectors, various valve
types, pulsation dampeners, injection units, etc.
21
PHYSICAL TREATMENT
High pressure demands can be fulfilled with a compact pump design (less stages) by operating at over-synchronous speed.
Factory configured CRE's with reinforced chambers and impellers can be an option. The motor size must be adjusted
accordingly.
Our variable frequency drives (VFD) can automate backwash through the use of sensors, so that no PLC is needed in simple
filtration systems.
The DDA FCM can accurately dose the right amount of chemicals so that the membranes are clean and protected, while the
DID probes and controller can adjust the dosing pump based on changing water quality parameters.
Pumps
Vertical multistage pumps - CR/CRE Endsuction close coupled multistage pumps - CM/CME
CM, CME are reliable, quiet and compact horizontal
Vertical, multistage centrifugal pump with suction and end-suction pumps. The modular pump design makes it
discharge ports on the same level. easy to make customised solutions.
Endsuction close coupled single-stage pumps - NB/NBE Endsuction long coupled single-stage pumps - NK/NKE
End-suction close-coupled pumps according to EN 733. The Standard pumps according to EN 733. The pump has an
pump has an axial suction port, radial discharge port, axial suction port, a radial discharge port and horizontal
horizontal shaft and a back pull-out design enabling shaft. It is of the back pull-out design enabling removal of
removal of the motor, motor stool, cover and impeller the coupling, bearing bracket and impeller without
without disturbing the pump housing or pipework. disturbing the motor, pump housing or pipework.
Flow max.: 1401 m³/h Head max.: 177 m Flow max.: 1401 l/s Head max.: 177 m
Endsuction long coupled single-stage pumps - NKG/NKGE Horizontal multistage pumps - BM

Standard pumps according to ISO 2858 with axial suction High pressure booster modules are used for boosting, liquid
port, a radial discharge port and horizontal shaft. It is of the transfer and circulation in systems under a high static
back pull-out design enabling removal of the coupling, pressure. Modules of different sizes can be combined and
bearing bracket and impeller without disturbing the motor, connected either in series or in parallel to meet exact Q/H
pump housing or pipework. requirements.
Liquid temperature: -25..140 °C p max.: 25 bar Liquid temperature: 0..45 °C
Horizontal multistage pumps - BMS Horizontal multistage pumps - BMSX

A BMSX booster system consists of a BMS hs high-speed
The Grundfos BMS range consists of hp (high pressure) and pump, a BM hp high-inlet-pressure pump and an isobaric
hs (high speed) versions. BMS hp are suitable for industrial pressure exchanger. It has a unique design dedicated to
and water supply applications where the inlet pressure is seawater and brackish water desalination.
high. BMS hs enables the creation of high pressure.

22
PHYSICAL TREATMENT
Digital Dosing Pumps - SMART Digital S/XL Customised Solutions - Custom-Built Pumps
SMART Digital diaphragm dosing pump with powerful Customised pumps to meet specific application challenges
variable-speed stepper motor (S) or powerful PMS (temperatures, pressures, difficult liquids) or installation
(Permanent Magnet Synchronous) motor (XL) and requirements (ambient conditions) not covered by the
FlowControl system to automatically detect malfunctions. standard pump range. It is a modular platform built on
High-end solution for complex and demanding applications stocked components. For more information please contact
with turn-down ratio up to 1:3000. Grundfos sales.
Flow max.: 200 l/h

Optimisation services - Energy Optimisation Offering
A Grundfos Energy Check or Energy Audit will help you find

hidden savings in your pump installation. It can also help to
reduce your operating expenses and reach your
sustainability targets.



23
PHYSICAL TREATMENT
Flow Sensors - VFI/VFS Flow Sensors - MAG 3100, 5100, 8000

Flow and temperature sensors designed to be robust and Several variants of the Mag Flow system are available,
accurate. They use our Silicoat® coating to be in direct depending on needed requirements and specifications. In
contact with the media and provide stable signals. general, the system consists of a flow meter and a
transmitter of choice. MAG 3100 covers all the applications
which the other industry specific sensors do not cover.
Drives
External Frequency Converters - CUE Drive Accessories - Sine-wave filter
CUE is a complete range of external frequency converters Sine wave filters have a high degree of filtering, resulting in
designed for speed control of a wide range of Grundfos a high reduction of the stress on the motor insulation
pumps. CUE has a built-in PI controller and offers the same system. At the same time, they reduce the acoustic noise
functionality and user-interface as Grundfos E-pumps. from the motor. Motor losses are reduced due to the fact
Power range up to 250 kW. that a sine-wave filter converts the output pulses of the
frequency converter into at sine-wave-shaped.
24
PHYSICAL TREATMENT
Systems
Application-specific bundles - iQ range Application-specific bundles - iSOLUTIONS for Reverse Osmosis (iRO)
Standardised plugandplay kits for low pressure reverse
The iSOLUTIONS Q-pump range consists of CRNE osmosis systems. Standardised solutions are available in six
high-pressure pumps, specifically designed for maximum prepackaged kits consisting of Grundfos components
utilization of the MGE motor for high pressure applications. selected to cover the requirements of different flow and
The hydraulic part has a flipped stack and reinforced pressure systems.
chambers. It is optimised for greater Q/H performance with
higher maximum speeds.

Chlorine Dioxide Systems - Oxiperm Pro Gas Warning Systems - DIA-G
Compact pre-mounted chlorine dioxide preparation and DIA-G gas warning systems monitor the concentration of
dosing system. Oxiperm Pro generates a ClO2 solution from dangerous gasses with up to two gas sensors. The range
diluted NaClO2, HCl and water and supports flow also includes accessories like battery backup, horn and
proportional or setpoint controlled dosing. Accessories for flashlight to complete the installation. Available monitoring
installation and measurement of ClO2 content are part of parameters: chlorine, chlorine dioxide, hydrochloric acid,
the product range. Max. ClO2 prep. quantity: 60 g/h ammonia and ozone.
Accessories
25
DISINFECTION
Oxiperm Pro offers onsite production of chlorine dioxide, that avoids chemicals transport and unnecessary handling.
Chlorine dioxide has a high efficiency at a broad pH range, while it does not react with organics to form THMs or ammonia
nitrogen.
Pumps
Digital Dosing Pumps - SMART Digital S/XL Mechanical Dosing Pumps - DMH
SMART Digital diaphragm dosing pump with powerful The DMH range is a series of extremely strong, robust
variable-speed stepper motor (S) or powerful PMS hydraulically actuated piston diaphragm dosing pumps for
(Permanent Magnet Synchronous) motor (XL) and applications requiring reliable dosing and high-pressure
FlowControl system to automatically detect malfunctions. capability, such as process engineering. The range is highly
High-end solution for complex and demanding applications versatile: it covers a wide flow range and offers a variety of
with turn-down ratio up to 1:3000. dosing head sizes, materials and accessories.


Flow Sensors - MAG 3100, 5100, 8000 M&C for Dosing & Disinfection - DID
Several variants of the Mag Flow system are available, The DID system with bypass flow cell is intended for
depending on needed requirements and specifications. In monitoring and control of disinfectants, pH, ORP,
general, the system consists of a flow meter and a conductivity and temperature. The system is preassembled
transmitter of choice. MAG 3100 covers all the applications on a common backplate and includes a control unit CU382
which the other industry specific sensors do not cover. as well as the water parameter sensor(s). Several
p max.: 3 bar
26
DISINFECTION
Systems
Application-specific bundles - iSOLUTIONS for Cooling Towers Dosing Skid Systems - DSS
Pre-selected and pre-commissioned with digital controls Dosing skid systems range from pre-engineered, standard
perfectly integrated for premium reliability and efficiency one, two and three pump systems, to custom systems with
consisting of: NB pump, RPI/T sensors, CUE drive and MPC. multiple pumps and tanks all piped on a common skid
complete with controls.
Dosing Tank Stations - DTS

Dosing tank stations are intended for storing and dosing
liquids. Many different configurations can be selected
flexibly to fulfil various dosing tasks. They are available in 6
tank sizes: 60 l, 100 l, 200 l, 300 l, 500 l and 1000 l.

Accessories
27
SEA WATER DESALINATION
By bundling the BMS hs, BMS hp and pressure exchanger, energy consumption can be reduced to as low as 2 kWh/m³ of
produced water – with capacities up to 1,500 m³/day.
A product range designed for its environment with resistant components made of super duplex stainless steel, polymer and
ceramic.
Protect your membranes with accurate dosage of chemicals with the DDA FCM, while being able to react to water quality
changes with the DID probes and controller.
Pumps
Vertical multistage pumps - CR/CRE Endsuction close coupled single-stage pumps - NBG/NBGE
Close-coupled pumps according to ISO 2858. Flanges are PN
Vertical, multistage centrifugal pump with suction and 16 with dimensions according to AS2129 table E. The pump
discharge ports on the same level. has an axial suction port, radial discharge port, horizontal
shaft and a back pull-out design enabling removal of the
motor, motor stool, cover and impeller without disturbing



28
Digital Dosing Pumps - SMART Digital S/XL Customised Solutions - Custom-Built Pumps
SMART Digital diaphragm dosing pump with powerful Customised pumps to meet specific application challenges
variable-speed stepper motor (S) or powerful PMS (temperatures, pressures, difficult liquids) or installation
(Permanent Magnet Synchronous) motor (XL) and requirements (ambient conditions) not covered by the
FlowControl system to automatically detect malfunctions. standard pump range. It is a modular platform built on
High-end solution for complex and demanding applications stocked components. For more information please contact
with turn-down ratio up to 1:3000. Grundfos sales.
Flow max.: 200 l/h


Service offerings
Laser Alignment

Communication Interfaces - CIM/CIU Communication Interface - MI 301
Communication Interface Module/Communication Grundfos remote controls used for installation, data
Interface Unit is the range of communication options from monitoring, fault information and configuration of
Grundfos. They enable you to connect your product to the Grundfos pumps and systems, by radio or IR connections.
wide range of field bus standards.

29
Pump control - Control CUE Pump control - Control MPC

Grundfos Control CUE is a series of external frequency
converters designed for speed control of a wide range of Control MPC controls up to six identical pumps connected
Grundfos pumps. The Frequency converter is delivered in parallel. It uses advanced algorithms to optimise
installed in a cabinet with main switch, circuit breaker, and performance and minimise energy consumption

Flow Sensors - VFI/VFS Flow Sensors - MAG 3100, 5100, 8000

Flow and temperature sensors designed to be robust and Several variants of the Mag Flow system are available,
accurate. They use our Silicoat® coating to be in direct depending on needed requirements and specifications. In
contact with the media and provide stable signals. general, the system consists of a flow meter and a
30
Drives
Systems
Application-specific bundles - iSOLUTIONS for Reverse Osmosis (iRO) Booster Systems - Hydro MPC, Hydro Multi-E
Standardised plugandplay kits for low pressure reverse Advanced and energy efficient pressure boosting system for
osmosis systems. Standardised solutions are available in six boosting of clean water. Available with 2 - 6 (2 - 4 for
prepackaged kits consisting of Grundfos components Multi-E) parallel connected pumps, integrated advanced
selected to cover the requirements of different flow and controller and all necessary fittings.
pressure systems.



31
Service offerings
Laser Alignment
Accessories
32
Wastewater Treatment &
Reuse
Handling wastewater is a crucial part of any industrial water solution, and pumps play a key role
in every application. Often, wastewater in industrial applications can be unpredictable, and an
industrial wastewater solution must be tough enough to deal with everything from grit and
grease to large particles. Wastewater pumps need to be efficient, reliable and intelligent to
handle these changing wastewater qualities. You also need to be certain that the water leaving
the system is of the right quality before it enters the sewer or the environment.
“As you know, chemicals are always a big risk. So for us it was very
time-saving and stress-saving to get a complete dosing solution
from Grundfos. We got the full cabinets with the dosing pumps, all
the piping, the valves, everything was included, so we were very
happy with that. In addition, the Grundfos pumps have a software
with flow control. And that guarantees that you're dosing what
you need to be dosing.”
Bryan de Bel, Project

Manager with turnkey
WWTP contractor Pantarein
(about Carlsberg Fredericia
project)
WASTEWATER TRANSFER
Grundfos prefabricated pumping stations are cost effective and flexible, with already built-in components such as pumping
and cables.
Grundfos SEG, SL and SE wastewater pumps have built in AUTOADAPT to adjust to operating conditions.
Grundfos dedicated controllers control up to 6 wastewater pumps to provide continuous energy optimization according to
duty point.
The anticlogging function on the DC controller stops the pumps from blocking by acting during abnormal events.
Grundfos packaged pumping stations with LC controller and CIM communication can provide: Real time pump control and
alerts (high level, pump failures, warning logs, dry run etc).
Vortex pump and S tube reduce clogging issue for high solid with larger length.
Pumps
Submersible wastewater pumps - S Submersible wastewater pumps - SE, SE1, SEV
The S pumps are a range of free-flow channel impeller Submersible Grundfos SE sewage pumps are fitted with
pumps specifically designed for pumping sewage and either S-tube (SE1) or SuperVortex impeller (SEV). The free
wastewater in a wide range of municipal and industrial passage through the pump varies from 50-100 mm
applications. depending on size.
Liquid temperature: 0..50 °C Liquid temperature: 0..40 °C
Submersible wastewater pumps - SEG Submersible wastewater pumps - SL

Submersible Grundfos SEG sewage grinder pumps are Submersible Grundfos SL sewage pumps are fitted with an
designed for pumping wastewater, sludge-containing S-tube® impeller. The free passage through the pump varies
water, and sewage. Fitted with a patented grinder system from 50-100 mm depending on size.
designed to grind the media.
Flow max.: 10 l/s Head max.: 48 m Flow max.: 83 l/s Head max.: 31 m
Liquid temperature: 0..40 °C p max.: 6 bar Liquid temperature: 0..40 °C p max.: 6 bar
Submersible wastewater pumps - SLV Submersible wastewater pumps - AP/APG

Submersible Grundfos SLV sewage pumps are fitted with a AP pumps are designed for pumping wastewater,
SuperVortex impeller. The free passage through the pump sludge-containing water, groundwater and sewage. APG are
varies from 50-100 mm depending on size. equipped with cutter system for grinding solids into small
pieces.
Liquid temperature: 0..40 °C p max.: 6 bar Liquid temperature: 0..40 °C
Submersible wastewater pumps - EF

Grundfos EF pumps have a single-vane, semi-open impeller
for 30 mm free passage, designed for pumping effluent and
other liquids such as drainage and surface water with fibres
and small impurities.
Flow max.: 12 l/s Head max.: 23 m

34
WASTEWATER TRANSFER
Service offerings
Customized Service Agreement Commissioning

Motor Protection - MP 204 Pump control - Control DC
MP 204 protects the motor against overload, dry running Grundfos Control DC is a control system designed for
and incipient motor defects based on many parameters like: installation in municipal wastewater transportation
supply voltage, phase sequence or harmonic distortion. It installations, commercial buildings or network pumping
disconnects the contactor if, for example, the current stations with up to six wastewater pumps. Advanced
exceeds the preset value. It can be used stand-alone or for control and data communication are also possible.
Pump control - CU362 Level Control - LC 231 / LC 241

The CU 362 control unit is a combined controller and LC 231 pump controllers are designed for level control,
user-friendly control panel with nine buttons and a large monitoring and protection of pumping systems, one or two
graphical LCD display. On the operator display, the current pumps starting DOL up to 12 Amp. LC 241 level controllers
status of the system is shown. The actual positions of the are designed for waste water pumping systems, monitoring
pumps, mixer and measuring sensors are shown in the and control of one or two pumps, up to 72 Amp.
display.

Flow Sensors - MAG 3100, 5100, 8000 Pump control accessories - IO (for wastewater pumps)
Several variants of the Mag Flow system are available, Various input and output modules for control solutions.
depending on needed requirements and specifications. In
general, the system consists of a flow meter and a
35
WASTEWATER TRANSFER
Drives
Systems
Prefabricated pumping stations - PS.G, PS.R, PS.W
Prefabricated pumping stations are designed for collection
and pumping of drainage water, rainwater or wastewater.
Features: sturdy materials, well-designed polyethylene pits,
all necessary accessories such as pipes and valves, as well as
reliable controllers.
Service offerings
Customized Service Agreement Commissioning
Accessories
Wastewater Accessories - Installation sets, lifting devices, chains, ...
Accessories designed for wastewater solutions:
Dry/submerged installation sets, lifting devices, chains, ...
36
CHEMICAL TREATMENT
CU 382 control unit handles number of analogue/digital input/output for control and monitoring of water quality and
accordingly have dosing control (example: pH control, ClO2 dosing, Cl dosing etc.).
Polydos for coagulation/flocculation: Compact and flexible installation of a fully integrated system including material
handling, preparation and maturing, and solution dosing.
Agitators
Mixers - AMD, AMG, SMD, SMG
Grundfos mixers are designed for mixing, i.e.

homogenisation and suspension of low/medium viscosity
liquids in small tanks and pumping stations.
Pumps
Endsuction close coupled single-stage pumps - NB/NBE Submersible wastewater pumps - S
End-suction close-coupled pumps according to EN 733. The The S pumps are a range of free-flow channel impeller
pump has an axial suction port, radial discharge port, pumps specifically designed for pumping sewage and
horizontal shaft and a back pull-out design enabling wastewater in a wide range of municipal and industrial
removal of the motor, motor stool, cover and impeller applications.
Submersible wastewater pumps - SE, SE1, SEV Submersible wastewater pumps - SEG
Submersible Grundfos SE sewage pumps are fitted with Submersible Grundfos SEG sewage grinder pumps are
either S-tube (SE1) or SuperVortex impeller (SEV). The free designed for pumping wastewater, sludge-containing
passage through the pump varies from 50-100 mm water, and sewage. Fitted with a patented grinder system
depending on size. designed to grind the media.
Liquid temperature: 0..40 °C Liquid temperature: 0..40 °C p max.: 6 bar
Submersible wastewater pumps - SL Submersible wastewater pumps - SLV

Submersible Grundfos SL sewage pumps are fitted with an Submersible Grundfos SLV sewage pumps are fitted with a
S-tube® impeller. The free passage through the pump varies SuperVortex impeller. The free passage through the pump
from 50-100 mm depending on size. varies from 50-100 mm depending on size.
37
CHEMICAL TREATMENT
Digital Dosing Pumps - SMART Digital S/XL Digital Dosing Pumps - DME
Digital diaphragm dosing pump with variable-speed motor
SMART Digital diaphragm dosing pump with powerful drive. For enhanced accuracy, the pump can be calibrated to
variable-speed stepper motor (S) or powerful PMS the actual installation by means of a simple calibration
(Permanent Magnet Synchronous) motor (XL) and function. The turndown ratio is 1 to 800 with the same
FlowControl system to automatically detect malfunctions. accuracy and uniform dosage with reduced pulsation
High-end solution for complex and demanding applications throughout the capacity range.

Liquid temperature: -10..50 °C p max.: 16 bar p max.: 10 bar
Mechanical Dosing Pumps - DMX Mechanical Dosing Pumps - DMH

high-quality motors, DMX pumps require minimum The DMH range is a series of extremely strong, robust
maintenance and are the best choice for many dosing hydraulically actuated piston diaphragm dosing pumps for
applications. The DMX range is highly versatile: it covers a applications requiring reliable dosing and high-pressure
wide flow range and offers a variety of dosing head sizes, capability, such as process engineering. The range is highly
materials and accessories. versatile: it covers a wide flow range and offers a variety of
dosing head sizes, materials and accessories.


Grundfos sales.
Service offerings
All-In-Maintenance

38
CHEMICAL TREATMENT
Motor Protection - Control MP 204 Level Transmitters - Level Transmitter S, E, W

Pump controller system designed for water utility market. Hydrostatic level transmitters with different versions. S:
Complete protection of one pump. applicable for most wastewater, drinking water and other
Communication Interfaces - E-Box Pump control accessories - IO (for wastewater pumps)

The E-Box device enables our digital dosing pumps SMART Various input and output modules for control solutions.
Digital S to communicate with a wired transmission to a
various range of fieldbus standards.
Systems
Dosing Skid Systems - DSS Chemical Preparation Systems - Polydos
Dosing skid systems range from pre-engineered, standard Automatic preparation systems for polymer solutions.
one, two and three pump systems, to custom systems with Polydos systems either work according to the 3-chamber
multiple pumps and tanks all piped on a common skid flow principle for dry or concentrated liquid polymers
complete with controls. (Polydos 412) or according to the 2 chamber flow principle
for use with liquid polymers only (Polydos 420/460). Max.
polymer solution preparation quantity 10 000 l/h
Service offerings
All-In-Maintenance
Accessories
Dosing Pump Accessories - General and Tank Accessories Wastewater Accessories - Installation sets, lifting devices, chains, ...
Comprehensive range of accessories for safe operation Accessories designed for wastewater solutions:
covering every requirement when dosing with Grundfos Dry/submerged installation sets, lifting devices, chains, ...
39
BIOLOGICAL TREATMENT
SE/SL come in three hydraulic concepts for different wastewater contamination levels (semi-open, closed and free flow
impellers). The product range is designed for its environments, with extreme durability that covers aggressive
environments.
Grundfos mixers and flowmakers keep particles evenly distributed in the wastewater and sludge and can be controlled with
Grundfos variable speed drive for optimised energy efficiency.
The Aerojet can help to avoid odour problems during wastewater storage and keep the treatment process running. Since it
is submersed, no harmful aerosols are dispersed into the surroundings.
Agitators
Flowmakers - AFG Mixers - AMD, AMG, SMD, SMG
The Grundfos range of horizontal, planetary gear drive AFG
flowmakers are designed for flowmaking, i.e. keeping liquids Grundfos mixers are designed for mixing, i.e.
moving in low/medium viscosity liquids. Fitted with motors homogenisation and suspension of low/medium viscosity
of 1.5-7.5 kW. liquids in small tanks and pumping stations.
Recirculation pumps - SRG

Grundfos SRG recirculation pumps are designed for the
pumping of sludge from one tank to another in sewage
treatment plants and for other pump applications involving
a high flow rate and low head.

Pumps
Endsuction close coupled single-stage pumps - NB/NBE Submersible wastewater pumps - S
End-suction close-coupled pumps according to EN 733. The The S pumps are a range of free-flow channel impeller
pump has an axial suction port, radial discharge port, pumps specifically designed for pumping sewage and
horizontal shaft and a back pull-out design enabling wastewater in a wide range of municipal and industrial
removal of the motor, motor stool, cover and impeller applications.
Submersible wastewater pumps - SE, SE1, SEV Submersible wastewater pumps - SEG
Submersible Grundfos SE sewage pumps are fitted with Submersible Grundfos SEG sewage grinder pumps are
either S-tube (SE1) or SuperVortex impeller (SEV). The free designed for pumping wastewater, sludge-containing
passage through the pump varies from 50-100 mm water, and sewage. Fitted with a patented grinder system
depending on size. designed to grind the media.
Liquid temperature: 0..40 °C Liquid temperature: 0..40 °C p max.: 6 bar
40
Submersible wastewater pumps - SL Submersible wastewater pumps - SLV

Submersible Grundfos SL sewage pumps are fitted with an Submersible Grundfos SLV sewage pumps are fitted with a
S-tube® impeller. The free passage through the pump varies SuperVortex impeller. The free passage through the pump
from 50-100 mm depending on size. varies from 50-100 mm depending on size.
Submersible wastewater pumps - AP/APG Submersible wastewater pumps - EF

AP pumps are designed for pumping wastewater, Grundfos EF pumps have a single-vane, semi-open impeller
sludge-containing water, groundwater and sewage. APG are for 30 mm free passage, designed for pumping effluent and
equipped with cutter system for grinding solids into small other liquids such as drainage and surface water with fibres
pieces. and small impurities.




41

Level Transmitters - Level Transmitter S, E, W Communication Interfaces - E-Box

Hydrostatic level transmitters with different versions. S: The E-Box device enables our digital dosing pumps SMART
applicable for most wastewater, drinking water and other Digital S to communicate with a wired transmission to a
media usages, W: wastewater, E: endurance and robustness various range of fieldbus standards.
Pump control accessories - IO (for wastewater pumps)

Various input and output modules for control solutions.
Systems
Dosing Skid Systems - DSS
Dosing skid systems range from pre-engineered, standard
one, two and three pump systems, to custom systems with
multiple pumps and tanks all piped on a common skid
Accessories
Dosing Pump Accessories - General and Tank Accessories Wastewater Accessories - Installation sets, lifting devices, chains, ...
Comprehensive range of accessories for safe operation Accessories designed for wastewater solutions:
covering every requirement when dosing with Grundfos Dry/submerged installation sets, lifting devices, chains, ...
42
PHYSICAL TREATMENT
accordingly.
Pumps
Vertical multistage pumps - CR/CRE Endsuction close coupled single-stage pumps - NBG/NBGE
Close-coupled pumps according to ISO 2858. Flanges are PN
Vertical, multistage centrifugal pump with suction and 16 with dimensions according to AS2129 table E. The pump
discharge ports on the same level. has an axial suction port, radial discharge port, horizontal

43
PHYSICAL TREATMENT





Service offerings
Laser Alignment

44
PHYSICAL TREATMENT

Level Transmitters - Level Transmitter S, E, W Flow Sensors - MAG 3100, 5100, 8000
Hydrostatic level transmitters with different versions. S: Several variants of the Mag Flow system are available,
applicable for most wastewater, drinking water and other depending on needed requirements and specifications. In
media usages, W: wastewater, E: endurance and robustness general, the system consists of a flow meter and a
strengthened product. transmitter of choice. MAG 3100 covers all the applications
M&C for Dosing & Disinfection - DID Communication Interfaces - E-Box

The DID system with bypass flow cell is intended for The E-Box device enables our digital dosing pumps SMART
monitoring and control of disinfectants, pH, ORP, Digital S to communicate with a wired transmission to a
conductivity and temperature. The system is preassembled various range of fieldbus standards.
p max.: 3 bar
Systems
Booster Systems - Hydro MPC, Hydro Multi-E Dosing Skid Systems - DSS
Advanced and energy efficient pressure boosting system for Dosing skid systems range from pre-engineered, standard
boosting of clean water. Available with 2 - 6 (2 - 4 for one, two and three pump systems, to custom systems with
Multi-E) parallel connected pumps, integrated advanced multiple pumps and tanks all piped on a common skid
controller and all necessary fittings. complete with controls.

Service offerings
Laser Alignment
45
PHYSICAL TREATMENT
Accessories
46
DISINFECTION
Pumps


Level Transmitters - Level Transmitter S, E, W M&C for Dosing & Disinfection - DID
Hydrostatic level transmitters with different versions. S: The DID system with bypass flow cell is intended for
applicable for most wastewater, drinking water and other monitoring and control of disinfectants, pH, ORP,
media usages, W: wastewater, E: endurance and robustness conductivity and temperature. The system is preassembled
strengthened product. on a common backplate and includes a control unit CU382
p max.: 3 bar
Systems
Dosing Skid Systems - DSS
Dosing skid systems range from pre-engineered, standard
one, two and three pump systems, to custom systems with
multiple pumps and tanks all piped on a common skid
47
DISINFECTION
Gas Warning Systems - DIA-G

DIA-G gas warning systems monitor the concentration of
dangerous gasses with up to two gas sensors. The range
also includes accessories like battery backup, horn and
flashlight to complete the installation. Available monitoring
parameters: chlorine, chlorine dioxide, hydrochloric acid,
ammonia and ozone.
Accessories
48
Industrial Heating
Grundfos supplies thoroughly tested, variable frequency drive-controlled pumps that optimise the
boiler feed process. Designed with low NPSH, these solutions cater to systems with poor inlet
conditions. This ensures cavitation-free operation even outside the pump’s normal duty range.
The Grundfos air-cooled top shaft seal solution eliminates the need for external cooling in
high-temperature applications.
"We're seeing a greater energy efficiency of the boiler, gas usage,

steam quality is better, control of level is better. No failure rates.
No problems whatsoever."
Scott Curran, Maintenance

Team Leader, William Grant
& Sons' Girvan Distillery
BOILER SYSTEM
Low NPSH versions (oversized impeller in 1st stage) for boiler feed pumps can better handle poor inlet pressure and hot
water.
Some installations result in same temperatures in the feed pumps as in the boiler. With air-cooled top the shaft seals are
protected.
Direct boiler feed with speed-controlled pumps replaces the modulating valves and leads to lower energy consumption, less
stress on components and better steam quality.
Stable operation with pump curve compensation for low flows with Grundfos frequency converters.
Using a level sensor in the boiler for optimum level leads to better steam quality, efficiency and reliability.
MAGdrive or double shaft seal to prevent from air entering the pump in duty/stand-by configurations.
Pumps
Inline single-stage pumps - TP/TPE, TPD/TPED Digital Dosing Pumps - SMART Digital S/XL
Grundfos TP/TPE pumps are single-stage, close-coupled
in-line centrifugal pumps with mechanical shaft seal and SMART Digital diaphragm dosing pump with powerful
primely for applications such as heating/cooling/district variable-speed stepper motor (S) or powerful PMS
energy. TPD/TPDE pumps are the twin-head version. (Permanent Magnet Synchronous) motor (XL) and
FlowControl system to automatically detect malfunctions.
High-end solution for complex and demanding applications
Flow max.: 4374 m³/h Head max.: 139 m Flow max.: 200 l/h
Customised Solutions - Custom-Built Pumps Optimisation services - Energy Optimisation Offering
Customised pumps to meet specific application challenges A Grundfos Energy Check or Energy Audit will help you find
(temperatures, pressures, difficult liquids) or installation hidden savings in your pump installation. It can also help to
requirements (ambient conditions) not covered by the reduce your operating expenses and reach your
standard pump range. It is a modular platform built on sustainability targets.
Grundfos sales.
50
BOILER SYSTEM
Service offerings
Commissioning


51
BOILER SYSTEM

M&C for Dosing & Disinfection - DIT-L, DIT-M

Photometers for several parameters (e.g. chlorine, ClO2, O3,
pH), with two different wavelengths, with high-quality
interference filters and long-term stable LEDs as light
Drives
Systems
Application-specific bundles - iSOLUTIONS for Boiler Feed Application-specific bundles - iQ range
With customised software, the variable speed Grundfos CRE
pumps can operate outside their set pump curves for The iSOLUTIONS Q-pump range consists of CRNE
unrivalled performance in boiler feed systems. high-pressure pumps, specifically designed for maximum
utilization of the MGE motor for high pressure applications.
The hydraulic part has a flipped stack and reinforced
52
BOILER SYSTEM
Booster Systems - Hydro MPC, Hydro Multi-E Dosing Skid Systems - DSS
Advanced and energy efficient pressure boosting system for Dosing skid systems range from pre-engineered, standard
boosting of clean water. Available with 2 - 6 (2 - 4 for one, two and three pump systems, to custom systems with
Multi-E) parallel connected pumps, integrated advanced multiple pumps and tanks all piped on a common skid
controller and all necessary fittings. complete with controls.

Dosing Tank Stations - DTS

Dosing tank stations are intended for storing and dosing
liquids. Many different configurations can be selected
flexibly to fulfil various dosing tasks. They are available in 6
tank sizes: 60 l, 100 l, 200 l, 300 l, 500 l and 1000 l.
Chlorine Dioxide Systems - Oxiperm Pro
Compact pre-mounted chlorine dioxide preparation and
dosing system. Oxiperm Pro generates a ClO2 solution from
diluted NaClO2, HCl and water and supports flow
proportional or setpoint controlled dosing. Accessories for
installation and measurement of ClO2 content are part of
the product range. Max. ClO2 prep. quantity: 60 g/h
Service offerings
Commissioning
Accessories
53
HEAT DISTRIBUTION
For high temperatures the shaft seals can be protected with air-cooled top.
The MAGNA3 features a built-in heat energy meter that can monitor system heat energy distribution and consumption to
reduce high energy demand caused by system imbalances.
Pumps
Inline single-stage pumps - TP/TPE, TPD/TPED Circulator pumps - MAGNA
Grundfos TP/TPE pumps are single-stage, close-coupled The Grundfos MAGNA circulator pumps are designed for
in-line centrifugal pumps with mechanical shaft seal and heating and cooling applications in commercial buildings.
primely for applications such as heating/cooling/district The pumps are available in both cast-iron and
energy. TPD/TPDE pumps are the twin-head version. stainless-steel and as twin-head variants. The pumps are
maintenance-free due to the canned-rotor type design.
Circulator pumps - ALPHA Customised Solutions - Custom-Built Pumps

The Grundfos ALPHA pumps are high-efficiency variable
speed circulators designed for heating, air-conditioning and Customised pumps to meet specific application challenges
also suitable for some industrial applications. (temperatures, pressures, difficult liquids) or installation
Grundfos sales.


54
HEAT DISTRIBUTION

Flow Sensors - VFI/VFS

Flow and temperature sensors designed to be robust and
accurate. They use our Silicoat® coating to be in direct
contact with the media and provide stable signals.
Systems

55
Industrial Cooling
As the demand for industrial production grows globally, so too does the demand for cooling. In
almost every industrial facility, ensuring the right temperature for machines and processes is
essential to production efficiency, reliability and quality. Grundfos offers pumps and solutions
equipped with variable frequency drive motors and sensors to create a complete solution that can
improve operational efficiency and achieve greater OPEX savings.
"With 40 to 60% energy savings on every project that we're going

for, then all the projects are being approved as quick as they're
suggested."
Daniel Gray, Energy and

Sustainability Manager,
Suntory Beverage & Food
GB & I
COOLING TOWER
Cooling tower fans can be intelligently controlled by MPC controllers.

The cooling tower with all its devices can be run with the pump controller without the need of another controller.
Differential temperature control (according to return temperature) based on RPI+T sensors can significantly reduce OPEX.
Onsite chlorine dioxide production will eliminate biofilm / legionella risk, improving the safety and efficiency of the cooling
tower.
Grundfos iSOLUTIONS (DID + DDA) can automate the blowdown process, which leads to lower OPEX through less water and
energy consumption.
When biocides reach a defined lower threshold, the DDAautomatically and accurately adjusts the dosing rate with up to 75
% chemical savings.
For scaling and fouling control the SMART Digital DDA with DDA can maintain a fixed flow and send alarms in case of e.g.
low amount of chemicals. Chemical cost can be reduced.
Pumps
Endsuction long coupled single-stage pumps - NK/NKE Inline single-stage pumps - TP/TPE, TPD/TPED
Standard pumps according to EN 733. The pump has an Grundfos TP/TPE pumps are single-stage, close-coupled
axial suction port, a radial discharge port and horizontal in-line centrifugal pumps with mechanical shaft seal and
shaft. It is of the back pull-out design enabling removal of primely for applications such as heating/cooling/district
the coupling, bearing bracket and impeller without energy. TPD/TPDE pumps are the twin-head version.
disturbing the motor, pump housing or pipework.
Horizontal splitcase pumps - LS Immersible Pumps - MTR/MTRE

Grundfos LS is a horizontal, single-stage or double-stages, Vertical multistage centrifugal pump designed for tank top
between bearings, split case pump. The axially split design mounting and for pumping of cooling lubricants and
allows easy removal of the top casing and access to the cutting oils for machine tools, cooling applications,
pump components without disturbing the motor or pipe industrial liquid transfer and similar applications.
work.
Liquid temperature: 0..100 °C p max.: 25 bar Liquid temperature: -10..90 °C p max.: 38 bar
Digital Dosing Pumps - SMART Digital S/XL Optimisation services - Energy Optimisation Offering
SMART Digital diaphragm dosing pump with powerful A Grundfos Energy Check or Energy Audit will help you find
variable-speed stepper motor (S) or powerful PMS hidden savings in your pump installation. It can also help to
(Permanent Magnet Synchronous) motor (XL) and reduce your operating expenses and reach your
FlowControl system to automatically detect malfunctions. sustainability targets.
Flow max.: 200 l/h

57
COOLING TOWER

Pump control - Control MPC Flow Sensors - VFI/VFS

Control MPC controls up to six identical pumps connected accurate. They use our Silicoat® coating to be in direct
in parallel. It uses advanced algorithms to optimise contact with the media and provide stable signals.
performance and minimise energy consumption

Drives
58
COOLING TOWER
Systems
Application-specific bundles - iSOLUTIONS for Cooling Towers Booster Systems - Hydro MPC, Hydro Multi-E
Pre-selected and pre-commissioned with digital controls Advanced and energy efficient pressure boosting system for
perfectly integrated for premium reliability and efficiency boosting of clean water. Available with 2 - 6 (2 - 4 for
consisting of: NB pump, RPI/T sensors, CUE drive and MPC. Multi-E) parallel connected pumps, integrated advanced


Chlorine Dioxide Systems - Oxiperm Pro
Compact pre-mounted chlorine dioxide preparation and
dosing system. Oxiperm Pro generates a ClO2 solution from
diluted NaClO2, HCl and water and supports flow
proportional or setpoint controlled dosing. Accessories for
installation and measurement of ClO2 content are part of
the product range. Max. ClO2 prep. quantity: 60 g/h
Accessories
59
CHILLER/EVAPORATOR/CONDENSER/COOLING WATER DISTRIBUTION
In chiller units, setting to constant temperature (with E-motor) instead of constant pressure (with regulating valve) saves
energy and smaller pumps can be used (running faster).
The viscosity of glycol and brines changes with the liquid temperature. Grundfos pumps can be supplied with oversized
motors that efficiently cope with higher load.
Critical cooling processes require that the temperature does not deviate. Grundfos speed-controlled pumps make sure that
the temperature is held constant.
Low temperatures in installations can cause water condensation in the motor at standstill. With Grundfos integrated motor
heaters condensation is completely avoided.
To prevent deformation because of thermal expansion CRN versions are recommended for low-temperature applications.
On the secondary side usually ice water, glycol, brine or alcohol-water are used as cooling liquid. This can be best handled
with stainless steel pumps.
Pumps
Endsuction close coupled multistage pumps - CM/CME Endsuction close coupled single-stage pumps - NBG/NBGE
CM, CME are reliable, quiet and compact horizontal Close-coupled pumps according to ISO 2858. Flanges are PN
end-suction pumps. The modular pump design makes it 16 with dimensions according to AS2129 table E. The pump
easy to make customised solutions. has an axial suction port, radial discharge port, horizontal
60
Inline single-stage pumps - TP/TPE, TPD/TPED Circulator pumps - MAGNA

Grundfos TP/TPE pumps are single-stage, close-coupled The Grundfos MAGNA circulator pumps are designed for
in-line centrifugal pumps with mechanical shaft seal and heating and cooling applications in commercial buildings.
primely for applications such as heating/cooling/district The pumps are available in both cast-iron and
energy. TPD/TPDE pumps are the twin-head version. stainless-steel and as twin-head variants. The pumps are
maintenance-free due to the canned-rotor type design.
Horizontal splitcase pumps - LS Immersible Pumps - MTR/MTRE

Grundfos LS is a horizontal, single-stage or double-stages, Vertical multistage centrifugal pump designed for tank top
between bearings, split case pump. The axially split design mounting and for pumping of cooling lubricants and
allows easy removal of the top casing and access to the cutting oils for machine tools, cooling applications,
pump components without disturbing the motor or pipe industrial liquid transfer and similar applications.
work.

Grundfos sales.
61

Pump control - Control MPC Flow Sensors - VFI/VFS

Control MPC controls up to six identical pumps connected accurate. They use our Silicoat® coating to be in direct
in parallel. It uses advanced algorithms to optimise contact with the media and provide stable signals.

Drives
Systems

62
Machining
Machining processes such as grinding, turning, milling, boring, sawing, wire cutting and spark
erosion lie at the heart of industrial manufacturing, where accuracy, economy and reliability
count for everything. The Grundfos range of immersible machine tool coolant pumps and
high-pressure pumps for machining processes offer unsurpassed accuracy and stability to make
sure that nothing interferes with these delicate processes. Integrated variable frequency drives
can be optionally supplied for increased system efficiency and flexibility. Our immersible pumps
suitable for machine tool applications offer a tank-mounted design, and our dry-installed
multi-stage pumps are also well-suited for machine tool applications.
"Grundfos has handled the changeover to the horizontally

mounted end-suction pump with open impeller very
professionally. You could already tell that the people are at home
in the machine tool industry."
Ralf Dörr, Process Planning

Gearboxes, ZF Saarbrücken
CLEAN SIDE
For installations with limited space (i.e., installation in cabinets or machine centers) high rpm versions with
over-synchronous operation can be suitable and provide the required flow and head, with a more compact pump design.
Leaking pumps may lead to contamination and costly downtime. MTR pumps eliminate this risk with drainage back to tank
(DBT).
When multiple duty points are needed, E-pumps and sensors can speed up and slow down pumps to fulfil larger Q/H areas,
and thereby replace 2 - 3 pumps or control valves with one E-pump.
For global OEMs stock costs can be reduced with our IE5 E-motors providing multiple approvals and 50/60 Hz in one pump.
The immersible pumps can be adjusted in length to accommodate different tank designs.
The pumps are available in complete stainless-steel execution for special applications.
The MTH/MTHE pumps are designed with compactness in mind increasing the ease of installation.
Pumps
Immersible Pumps - MTR/MTRE Immersible Pumps - SPK/SPKE
Vertical multistage centrifugal pump designed for tank top Vertical multistage centrifugal pump designed for tank top
mounting and for pumping of cooling lubricants and mounting and for pumping of cooling lubricants and
cutting oils for machine tools, cooling applications, cutting oils for machine tools, condensate transfer and
industrial liquid transfer and similar applications. similar applications.
Immersible Pumps - MTH/MTHE Immersible Pumps - MTC

Vertical multistage centrifugal pump designed for tank top Vertical multistage, immersible, self-priming, centrifugal
mounting and for pumping of cooling lubricants and pump for installation in tanks etc. Designed for pumping of
cutting oils for machine tools, cooling applications, cooling lubricants for machine tools, condensate transfer
industrial liquid transfer and similar applications. and similar applications.

Immersible Pumps - MTS/MTSE Vertical multistage pumps - CR/CRE

Screw spindle pump designed for pumping cooling
lubricants and cutting oils for machine tool applications. Vertical, multistage centrifugal pump with suction and
discharge ports on the same level.
Endsuction close coupled multistage pumps - CM/CME Endsuction close coupled single-stage pumps - NBG/NBGE
CM, CME are reliable, quiet and compact horizontal Close-coupled pumps according to ISO 2858. Flanges are PN
end-suction pumps. The modular pump design makes it 16 with dimensions according to AS2129 table E. The pump
easy to make customised solutions. has an axial suction port, radial discharge port, horizontal
64
CLEAN SIDE
Endsuction long coupled single-stage pumps - NKG/NKGE Endsuction close coupled single-stage pumps - NB/NBE
Standard pumps according to ISO 2858 with axial suction End-suction close-coupled pumps according to EN 733. The
port, a radial discharge port and horizontal shaft. It is of the pump has an axial suction port, radial discharge port,
back pull-out design enabling removal of the coupling, horizontal shaft and a back pull-out design enabling
bearing bracket and impeller without disturbing the motor, removal of the motor, motor stool, cover and impeller
pump housing or pipework. without disturbing the pump housing or pipework.
Endsuction long coupled single-stage pumps - NK/NKE Endsuction split coupled single-stage pumps - NBS/NBSE
Standard pumps according to EN 733. The pump has an Split-coupled end-suction pumps with NEMA motors and
axial suction port, a radial discharge port and horizontal ANSI flange fittings.
shaft. It is of the back pull-out design enabling removal of
the coupling, bearing bracket and impeller without
disturbing the motor, pump housing or pipework.

Service offerings
Commissioning


65
CLEAN SIDE
Pump control - Control MPC Level Transmitters - Level Transmitter S, E, W

Hydrostatic level transmitters with different versions. S:
Control MPC controls up to six identical pumps connected applicable for most wastewater, drinking water and other
in parallel. It uses advanced algorithms to optimise media usages, W: wastewater, E: endurance and robustness
performance and minimise energy consumption strengthened product.
M&C for Dosing & Disinfection - DID

monitoring and control of disinfectants, pH, ORP,
conductivity and temperature. The system is preassembled
p max.: 3 bar
Drives
Service offerings
Commissioning
66
DIRTY SIDE
The MTA pumps are available in different immersible lengths to accommodate different tank designs.
The MTA pumps are designed without shaft seal to increase service life.
The NBG/NKG pumps are built according toISO 5199/2858. The impeller is designed according to the super vortex principle;
thus, chips and fibers up to 25 mm will not clog up the pump.
The NBG/NKG pumps are available in different materials with a broad range of shaft seal combinations to accommodate
almost any customer requirement.
Pumps
Immersible Pumps - MTA Endsuction close coupled single-stage pumps - NBG/NBGE
Single stage pump for tank top mounting for pumping Close-coupled pumps according to ISO 2858. Flanges are PN
cooling lubricants and cutting oils for machine tool 16 with dimensions according to AS2129 table E. The pump
applications. has an axial suction port, radial discharge port, horizontal
Liquid temperature: 0..60 °C Liquid temperature: -25..140 °C p max.: 25 bar
Endsuction long coupled single-stage pumps - NKG/NKGE Endsuction close coupled single-stage pumps - MTB/MTBE
Standard pumps according to ISO 2858 with axial suction Close coupled end-suction pump with semi-open vortex
port, a radial discharge port and horizontal shaft. It is of the impeller. The pumps are designed specifically for the
back pull-out design enabling removal of the coupling, transfer of liquids containing solid particles in industrial
bearing bracket and impeller without disturbing the motor, machine tool applications.
pump housing or pipework.
67
DIRTY SIDE


Pump control - Control MPC M&C for Dosing & Disinfection - DID
Control MPC controls up to six identical pumps connected monitoring and control of disinfectants, pH, ORP,
in parallel. It uses advanced algorithms to optimise conductivity and temperature. The system is preassembled
performance and minimise energy consumption on a common backplate and includes a control unit CU382
p max.: 3 bar
Drives
68
Cleaning Processes
Part washing applications are notoriously demanding, as they often use aggressive liquids, high
temperatures and high pressures. Using conventional pumps, this would result in bulky
installations where the motor’s power is not fully utilised. Wash and clean applications in the
food processing industry, such as slaughterhouses and breweries, place restrictions on the
physical size of the pump, as the equipment either is installed in a cabinet or fitted on a trolley
moved by hand.
"By adjusting the pump capacity to the actual pressure required, a

saving of 90 percent in energy consumption and energy costs was
achieved. In the case of the parts cleaning system under
consideration, these measures save 51,410 kWh of electricity per
year and thus costs of around 6,200 €. With a total investment of
only 3,800 €, this results in a return on investment of over 100
percent. The efficiency measures developed can in principle be
extended to numerous comparable plants, enabling the company
to tap further savings potential."
Özkan Karakurt, WPS/WSE,

Mercedes-Benz plant
Untertürkheim
FOOD
accordingly.
Flow demand can change fast with large variations. Ramp and control trim can take stress fromthe pumps.
Standstill motor heaters are recommended for very cold ambient temperatures to reduce condensation. Drain holes might
also need to be opened.
Pumps
Endsuction close coupled single-stage pumps - MTB/MTBE Horizontal multistage pumps - BMS
Close coupled end-suction pump with semi-open vortex
impeller. The pumps are designed specifically for the The Grundfos BMS range consists of hp (high pressure) and
transfer of liquids containing solid particles in industrial hs (high speed) versions. BMS hp are suitable for industrial
machine tool applications. and water supply applications where the inlet pressure is
Immersible Pumps - MTR/MTRE Digital Dosing Pumps - SMART Digital S/XL

Vertical multistage centrifugal pump designed for tank top
mounting and for pumping of cooling lubricants and SMART Digital diaphragm dosing pump with powerful
cutting oils for machine tools, cooling applications, variable-speed stepper motor (S) or powerful PMS
industrial liquid transfer and similar applications. (Permanent Magnet Synchronous) motor (XL) and
70
FOOD
Service offerings
Commissioning



Communication Interfaces - E-Box

The E-Box device enables our digital dosing pumps SMART
Digital S to communicate with a wired transmission to a
various range of fieldbus standards.
71
FOOD
Drives
Systems
Application-specific bundles - iQ range Application-specific bundles - iSOLUTIONS Compact Performance
The most compact and cost effective full featured CRNE
The iSOLUTIONS Q-pump range consists of CRNE range possible sized to utilize full power in the primary
high-pressure pumps, specifically designed for maximum operating area, often saving a motor size compared to
utilization of the MGE motor for high pressure applications. traditional motor sizing. iCP is the perfect choice when
The hydraulic part has a flipped stack and reinforced avaliable space is tight and efficiency is paramount.


Service offerings
Commissioning
Accessories
72
NON FOOD
accordingly.
Flow demand can change fast with large variations. Ramp and control trim can take stress fromthe pumps.
Standstill motor heaters are recommended for very cold ambient temperatures to reduce condensation. Drain holes might
also need to be opened.
Pumps
73
NON FOOD
Endsuction close coupled single-stage pumps - MTB/MTBE Horizontal multistage pumps - BMS
Close coupled end-suction pump with semi-open vortex
impeller. The pumps are designed specifically for the The Grundfos BMS range consists of hp (high pressure) and
transfer of liquids containing solid particles in industrial hs (high speed) versions. BMS hp are suitable for industrial
machine tool applications. and water supply applications where the inlet pressure is
Immersible Pumps - MTR/MTRE Digital Dosing Pumps - SMART Digital S/XL

mounting and for pumping of cooling lubricants and SMART Digital diaphragm dosing pump with powerful
cutting oils for machine tools, cooling applications, variable-speed stepper motor (S) or powerful PMS
industrial liquid transfer and similar applications. (Permanent Magnet Synchronous) motor (XL) and

Grundfos sales.


74
NON FOOD


M&C for Dosing & Disinfection - DID Communication Interfaces - E-Box

The DID system with bypass flow cell is intended for The E-Box device enables our digital dosing pumps SMART
monitoring and control of disinfectants, pH, ORP, Digital S to communicate with a wired transmission to a
conductivity and temperature. The system is preassembled various range of fieldbus standards.
p max.: 3 bar
Drives
75
NON FOOD
Systems
Application-specific bundles - iQ range Application-specific bundles - iSOLUTIONS Compact Performance
The most compact and cost effective full featured CRNE
The iSOLUTIONS Q-pump range consists of CRNE range possible sized to utilize full power in the primary
high-pressure pumps, specifically designed for maximum operating area, often saving a motor size compared to
utilization of the MGE motor for high pressure applications. traditional motor sizing. iCP is the perfect choice when
The hydraulic part has a flipped stack and reinforced avaliable space is tight and efficiency is paramount.


Accessories
76
Process Fluid Transfer
Process liquids are liquids that are used in industrial processes for various purposes, such as
cooling, heating, cleaning, chemical reactions or as ingredients. Examples of process liquids
include water, oil, acids (e.g. hydrochloric acid and sulfuric acid), bases (e.g. sodium hydroxide and
potassium hydroxide), and solvents (e.g. ethanol and methanol). These liquids are used in a wide
range of industries, including food and beverage, chemical, pharmaceutical, and manufacturing.
Certain requirements to the pumps are important to consider when pumping process liquids such
as temperature, viscosity, corrosion/chemical resistance and safety. Grundfos offers the right
standard and customised solutions for a wide range of applications.
PROCESS FLUID TRANSFER
For high-viscous liquids precautions must be taken to ensure that the motor of the pump is not overloaded. The viscosity of
a pumped liquid depends strongly on the liquid temperature. We offer CR pumps with oversize motors for stable operation.
Pumps
Endsuction close coupled multistage pumps - CM/CME Vertical multistage pumps - CR/CRE
end-suction pumps. The modular pump design makes it Vertical, multistage centrifugal pump with suction and
easy to make customised solutions. discharge ports on the same level.
Customised Solutions - Custom-Built Pumps Immersible Pumps - MTR/MTRE

Customised pumps to meet specific application challenges mounting and for pumping of cooling lubricants and
(temperatures, pressures, difficult liquids) or installation cutting oils for machine tools, cooling applications,
requirements (ambient conditions) not covered by the industrial liquid transfer and similar applications.
Grundfos sales.

Endsuction close coupled single-stage pumps - NB/NBE Endsuction close coupled single-stage pumps - NBG/NBGE
End-suction close-coupled pumps according to EN 733. The Close-coupled pumps according to ISO 2858. Flanges are PN
pump has an axial suction port, radial discharge port, 16 with dimensions according to AS2129 table E. The pump
horizontal shaft and a back pull-out design enabling has an axial suction port, radial discharge port, horizontal
removal of the motor, motor stool, cover and impeller shaft and a back pull-out design enabling removal of the
without disturbing the pump housing or pipework. motor, motor stool, cover and impeller without disturbing
Endsuction long coupled single-stage pumps - NK/NKE Endsuction long coupled single-stage pumps - NKG/NKGE
Standard pumps according to EN 733. The pump has an Standard pumps according to ISO 2858 with axial suction
axial suction port, a radial discharge port and horizontal port, a radial discharge port and horizontal shaft. It is of the
shaft. It is of the back pull-out design enabling removal of back pull-out design enabling removal of the coupling,
the coupling, bearing bracket and impeller without bearing bracket and impeller without disturbing the motor,
disturbing the motor, pump housing or pipework. pump housing or pipework.
Service offerings
78

Communication Interfaces - CIM/CIU Pump control - Control CUE
Communication Interface Module/Communication Grundfos Control CUE is a series of external frequency
Interface Unit is the range of communication options from converters designed for speed control of a wide range of
Grundfos. They enable you to connect your product to the Grundfos pumps. The Frequency converter is delivered
wide range of field bus standards. installed in a cabinet with main switch, circuit breaker, and
Motor Protection - Control MP 204 Pump control - Control MPC

Pump controller system designed for water utility market.
Complete protection of one pump. Control MPC controls up to six identical pumps connected
in parallel. It uses advanced algorithms to optimise
M&C for Dosing & Disinfection - DID Pressure Sensors - DPI, DPS, RPI, RPS
The DID system with bypass flow cell is intended for Our pressure sensor ranges are designed to be robust,
monitoring and control of disinfectants, pH, ORP, accurate and reliable. Depending on the product family they
conductivity and temperature. The system is preassembled measure relative or differential pressure and temperature.
on a common backplate and includes a control unit CU382 They use our Silicoat coating to be in direct contact with the
as well as the water parameter sensor(s). Several media and provide stable signals.
p max.: 3 bar Liquid temperature: -30..120 °C
79
Level Transmitters - Level Transmitter S, E, W Flow Sensors - MAG 3100, 5100, 8000
Hydrostatic level transmitters with different versions. S: Several variants of the Mag Flow system are available,
applicable for most wastewater, drinking water and other depending on needed requirements and specifications. In
media usages, W: wastewater, E: endurance and robustness general, the system consists of a flow meter and a
strengthened product. transmitter of choice. MAG 3100 covers all the applications
Communication Interface - MI 301 Motor Protection - MP 204

Grundfos remote controls used for installation, data MP 204 protects the motor against overload, dry running
monitoring, fault information and configuration of and incipient motor defects based on many parameters like:
Grundfos pumps and systems, by radio or IR connections. supply voltage, phase sequence or harmonic distortion. It
Level Transmitters - MS1, M2, FS1 Flow Sensors - VFI/VFS

Float switches for level control/monitoring in tanks, Flow and temperature sensors designed to be robust and
pumping stations or similar applications. accurate. They use our Silicoat® coating to be in direct
contact with the media and provide stable signals.
Drives
Systems

80
Service offerings
81
Process Charts
Grundfos Products in Textile
Semiconductor Production Process
Pharmaceuticals and Personal Care Products
82
Food & Beverages
83
Mobility
84
GRUNDFOS Vietnam Company Ltd. PDF generated:
36 Ho Thi Tu, Quarter 2 2023-08-31
Hiep Phu Ward
Ho Chi Minh City Thu Duc City
Vietnam
[email protected]
http://www.grundfos.com
(+84) 28 6255 4747

Industry Portfolio Catalogue Vietnam en 50Hz

Uploaded by

Copyright:

Available Formats

Industry Portfolio Catalogue Vietnam en 50Hz

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Industry Portfolio Catalogue Vietnam en 50Hz

Uploaded by

Copyright:

Available Formats

Vietnam

Water Intake / Water Treatment Wastewater

Industrial Heating Industrial Cooling

Machining Cleaning Processes Process Fluid

Grundfos delivers a range of products,

8 Water Intake / Supply / Transfer

33 Wastewater Treatment & Reuse

77 Process Fluid Transfer

By taking a greater responsibility for the

We bring peace of mind to you by

We add value through:

Enhanced asset management

Service Agreements Repair Services Operation Services Optimisation Services

Grundfos Energy Earnings Spare Parts Installation Energy Check Advanced

All-In-Maintenance Repair Extended Warranty Energy Check Basic

Customized Service Agreement Laser Alignment

Standard Service Agreement Inspection

Broken pumps and stalled productions result in huge costs. Benefits:

A Customised Service Agreement is tailor-made to suit your Choose elements across:

We offer Installation by a skilled service technician to ensure Installation includes:

Alignment between pump and motor can cause unnecessary Benefits:

Your whole system is analysed according to a specific checklist by Benefits:

Expert service technicians verify that the installation is Benefits:

Energy Check Basic

Available Special conditions and limitations

"Not only have we seen an immediately improved water supply

Calvin Winch, Engineer,

Monitors, Controls and Sensors

Motor Protection - Control MP 204 Pump control - Control CUE

Pump control - CU 200, 300, 301 Pump control - Control MPC

Level Control - LC 232 / LC 242 Level Transmitters - MS1, M2, FS1

Level Transmitters - Level Transmitter S, E, W Flow Sensors - VFI/VFS

Liquid temperature: -30..120 °C

Liquid temperature: -30..120 °C

Endsuction long coupled single-stage pumps - NK/NKE Horizontal splitcase pumps - LS

All-In-Maintenance Customized Service Agreement

Laser Alignment Commissioning

Monitors, Controls and Sensors

Motor Protection - Control MP 204 Pump control - Control CUE

Pump control - CU 200, 300, 301 Pump control - Control MPC

Level Control - LC 232 / LC 242 Level Transmitters - MS1, M2, FS1

Level Transmitters - Level Transmitter S, E, W Flow Sensors - VFI/VFS

Liquid temperature: -30..120 °C

Liquid temperature: -30..120 °C

All-In-Maintenance Customized Service Agreement

Laser Alignment Commissioning

Endsuction long coupled single-stage pumps - NK/NKE Submersible groundwater pumps - SP

Customised Solutions - Custom-Built Pumps

Customised pumps to meet specific application challenges

Monitors, Controls and Sensors

Liquid temperature: -30..120 °C

M&C for Dosing & Disinfection - DID

Endsuction long coupled single-stage pumps - NK/NKE Horizontal splitcase pumps - LS

Monitors, Controls and Sensors

Motor Protection - Control MP 204 Pump control - Control CUE

Pump control - Control MPC Level Control - LC 232 / LC 242

Level Transmitters - MS1, M2, FS1 Level Transmitters - Level Transmitter S, E, W

Liquid temperature: -30..120 °C p max.: 3 bar

Flow max.: 1464 m³/h Head max.: 161 m

"Our small reverse osmosis 1000 lit./h system with activated