Jush

ANNEX N AWS D1.1/D1.
1M:2010
WELDING PROCEDURE SPECIFICATION (WPS) Yes

PREQUALIFIED __________ QUALIFIED BY TESTING __________
or PROCEDURE QUALIFICATION RECORDS (PQR) Yes
Identification # _________________________________
Revision _______ Date __________ By ____________
Company Name _______________________________ Authorized by __________________ Date __________
Welding Process(es) ____________________________ Type—Manual Semiautomatic
Supporting PQR No.(s) __________________________ Mechanized Automatic
JOINT DESIGN USED POSITION

Type: Position of Groove: ______________ Fillet: __________
Single Double Weld Vertical Progression: Up Down
Backing: Yes No
Backing: Backing Material: ELECTRICAL CHARACTERISTICS
Root Opening ______ Root Face Dimension ________ ______________________
Groove Angle: ___________ Radius (J–U) _________ Transfer Mode (GMAW) Short-Circuiting
Back Gouging: Yes No Method _______ Globular Spray
Current: AC DCEP DCEN Pulsed
BASE METALS Power Source: CC CV
Material Spec. _________________________________ Other ________________________________________
Type or Grade _________________________________ Tungsten Electrode (GTAW)
Thickness: Groove ____________ Fillet __________ Size: ______________
Diameter (Pipe) ________________________________ Type: ______________
FILLER METALS TECHNIQUE

AWS Specification______________________________ Stringer or Weave Bead: _________________________
AWS Classification _____________________________ Multi-pass or Single Pass (per side)_________________
Number of Electrodes ___________________________
Electrode Spacing Longitudinal ____________
SHIELDING Lateral_________________
Flux ___________________ Gas _________________ Angle _________________
Composition __________ Contact Tube to Work Distance ____________________
Electrode-Flux (Class)_____ Flow Rate ____________ Peening ______________________________________
______________________ Gas Cup Size _________ Interpass Cleaning: _____________________________
PREHEAT POSTWELD HEAT TREATMENT

Preheat Temp., Min. ____________________________ Temp. ________________________________________
Interpass Temp., Min. ___________ Max. _________ Time _________________________________________
WELDING PROCEDURE
Filler Metals Current
Pass or
Weld Type & Amps or Wire Travel
Layer(s) Process Class Diam. Polarity Feed Speed Volts Speed Joint Details
Form N-1 (Front)
354
ANNEX N AWS D1.1/D1.1M:2010
Procedure Qualification Record (PQR) # __________

Test Results
TENSILE TEST
Specimen Ultimate Tensile Ultimate Unit Character of Failure
Width Thickness Area
No. Load, lb Stress, psi and Location
GUIDED BEND TEST
Specimen
Type of Bend Result Remarks
No.
VISUAL INSPECTION
Appearance___________________________________ Radiographic-ultrasonic examination
Undercut _____________________________________ RT report no.: __________ Result ________________
Piping porosity ________________________________ UT report no.: ___________ Result ________________
Convexity_____________________________________ FILLET WELD TEST RESULTS
Test date _____________________________________ Minimum size multiple pass Maximum size single pass
Witnessed by__________________________________ Macroetch Macroetch
1. _______ 3. ________ 1. ________ 3. ________
2. _______ 2. ________
Other Tests All-weld-metal tension test
Tensile strength, psi _____________________________

Yield point/strength, psi __________________________
Elongation in 2 in, % ____________________________
Laboratory test no. _________________________
Welder’s name ________________________________ Clock no. ______________ Stamp no. _____________
Tests conducted by _________________________________________________________ Laboratory
Test number ___________________________________
Per __________________________________________
We, the undersigned, certify that the statements in this record are correct and that the test welds were prepared, welded, and
tested in conformance with the requirements of Clause 4 of AWS D1.1/D1.1M, (__________ ) Structural Welding Code—Steel.
(year)
Signed _______________________________________
Manufacturer or Contractor
By ___________________________________________
Title _________________________________________
Date _________________________________________
Form N-1 (Back)
358

Jush

Uploaded by

Copyright:

Available Formats

Jush

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jush

Uploaded by

Copyright:

Available Formats

ANNEX N AWS D1.1/D1.

WELDING PROCEDURE SPECIFICATION (WPS) Yes

JOINT DESIGN USED POSITION

FILLER METALS TECHNIQUE

PREHEAT POSTWELD HEAT TREATMENT

Form N-1 (Front)

Procedure Qualification Record (PQR) # __________

GUIDED BEND TEST

Other Tests All-weld-metal tension test

Tensile strength, psi _____________________________

Welder’s name __________________ Clock no. Stamp no. _

Tests conducted by _________________________________________________________ Laboratory

Test number ___________________________________

Form N-1 (Back)

You might also like