CP TD12 15 Technical Data ENU

CP TD12/15
Technical Data
CP TD12/15 Technical Data
© OMICRON electronics GmbH 2019. All rights reserved.

This technical data was extracted from the following manual: ENU 1226 05 01
All rights including translation reserved. Reproduction of any kind, for example, photocopying,
microfilming, optical character recognition and/or storage in electronic data processing systems,
requires the explicit consent of OMICRON.
The document content represents the technical status at the time of writing and is subject to change
without prior notice.
We have done our best to ensure that the information given in this document is useful, accurate and
entirely reliable. However, OMICRON does not assume responsibility for any inaccuracies which may
be present.
OMICRON translates this document from the source language English into a number of other
languages. Any translation of this document is done for local requirements, and in the event of a dispute
between the English and a non-English version, the English version of this document shall govern.
2 OMICRON
Technical data
1 Technical data
1.1 Technical data of the CP TD12/15 in combination with
the Control device
1.1.1 High-voltage output
Conditions: Signals below 45 Hz with reduced values possible. Capacitive linear loads.
Table 1-1: CP TD12 – High-voltage output
Terminal U THD I max S max t max

300 mA 3600 VA > 2 min
High-voltage output 0...12 kV AC <2%
100 mA 1200 VA > 60 min
Table 1-2: CP TD15 – High-voltage output
Terminal U THD I max S max t max

300 mA 4500 VA1 > 2 min
High-voltage output 0...15 kV AC <2%
100 mA 1500 VA > 60 min
1. Depending on Control device and power supply
1.1.2 Measurements
Test frequencies
Table 1-3: Test frequencies
Range Typical accuracy1

15...400 Hz error < 0.005 % of reading
1. "Typical accuracy" means at temperatures of 23 °C ± 5 K, after a warm-up time of more than 25 min, and in a frequency range
of 45 Hz to 65 Hz, 98 % of all units have an accuracy which is better than specified.
Only CPC 100 and CPC 80: TanDelta test card: Column "Hz" of the results table
Special displays in the frequency column "Hz" and their meanings:
*50 Hz (*60 Hz) Measurement mode suppressing the mains frequency interferences; doubles
the measurement time.
!30 Hz The selected test voltage is not available in Automatic measurement (applies to
frequencies below 45 Hz only).
?xx Hz Results with reduced accuracy, e.g., in case of a low testing voltage, influences
of partial discharge etc.
OMICRON 3
Filter for selective measurements

Conditions: f = 15 ... 400 Hz
Table 1-4: Filter for selective measurements
Filter Bandwidth Measurement time Stop band specification (attenuation)

f0 ± 5 Hz 2.2 s > 110 dB at fx = f 0 ± (5 Hz or more)
Test current (RMS, selective)

Table 1-5: Test current
Terminal Range Typical accuracy1 Conditions

IN A or error < 0.3 % of reading + 100 nA Ix < 8 mA
0...5 A AC
IN B2 error < 0.5 % of reading Ix > 8 mA
2. IN A (red) or IN B (blue), depending on the mode.
Test voltage (RMS, selective)

Table 1-6: CP TD12 – Test voltage
Condition: U > 2 kV
2 kV...12 kV AC error < 0.3 % of reading + 1 V
Table 1-7: CP TD15 – Test voltage
Condition: U > 2 kV
2 kV...15 kV AC error < 0.3 % of reading + 1 V
4 OMICRON
Technical data
Capacitance Cp (equivalent parallel circuit)

Table 1-8: Capacitance Cp
Range Typical accuracy1 Conditions

error < 0.05 % of reading + 0.1 pF Ix < 8 mA, Utest = 2 kV...10 kV
1 pF...3 µF
error < 0.2 % of reading Ix > 8 mA, Utest = 2 kV...10 kV
Dissipation factor DF (tan δ)

Table 1-9: Dissipation factor DF

f = 45...70 Hz, I < 8 mA,
0...10 % (capacitive) error < 0.1 % of reading + 0.005 % 2
Utest = 2 kV...10 kV
0...10000 % error < 0.5 % of reading + 0.02 % Utest = 2 kV...10 kV
2. Reduced accuracy of DF at mains frequency or its harmonics. Mains frequency suppression available by precisely selecting
a mains frequency of *50Hz or *60Hz in the "Hz" column.
Power factor PF (cos ϕ )

Table 1-10: Power factor Pf
2 f = 45...70 Hz, I < 8 mA,

0...10 % (capacitive) error < 0.1 % of reading + 0.005 % Utest = 2 kV...10 kV
0...100 % error < 0.5 % of reading + 0.02 % Utest = 2 kV...10 kV
2. Reduced accuracy of PF at mains frequency or its harmonics. Mains frequency suppression available by precisely selecting
a mains frequency of *50Hz or *60Hz in the "Hz" column.
Phase angle ϕ
Table 1-11: Phase angle ϕ

-90 °...+90 ° error < 0.01 ° Utest = 2 kV...10 kV
OMICRON 5
Impedance Z
Table 1-12: Impedance Z

1 kΩ...1200 MΩ error < 0.5 % of reading Utest = 2 kV...10 kV
Inductance Lx (equivalent serial circuit)

Table 1-13: Inductance Lx

1 H...1000 kH error < 0.3 % of reading
Quality factor QF
Table 1-14: Quality factor QF

0...1000 error < 0.5 % of reading + 0.2 %
> 1000 error < 5 % of reading
Power P, Q, S (selective)
Table 1-15: CP TD12 – Power P, Q, S

0...3.6 kW error < 0.5 % of reading + 1 mW
0...3.6 kVAR error < 0.5 % of reading + 1 mVAR
0...3.6 kVA error < 0.5 % of reading + 1 mVA
Table 1-16: CP TD15 – Power P, Q, S

0...4.5 kW2 error < 0.5 % of reading + 1 mW
0...4.5 kVAR2 error < 0.5 % of reading + 1 mVAR
0...4.5 kVA2 error < 0.5 % of reading + 1 mVA
2. Depending on Control device and power supply
6 OMICRON
Technical data
1.2 Mechanical data
Table 1-17: Mechanical data

Characteristic Rating
Dimensions CP TD12/15 460 × 317 × 223 mm
(W × H × D) 18.1 × 12.5 × 8.8 inches
Weight CP TD12 23 kg / 51 lb
CP TD15 24 kg / 53 lb
1.3 Environmental Conditions

Table 1-18: Climate
Operating –10…+55 ºC / +14…+131 ºF
Temperature Storage and –20…+70 ºC / –4…+158 ºF
transportation
Max. altitude 2000 m
Relative humidity 5…95 %; no condensation, tested according to IEC 60068-2-78
Table 1-19: Noise Immunity
Noise Immunity Electrostatic: 15 mA induced noise into any test lead without losing measurement
accuracy at maximum interference to specimen current of 20:1
Electromagnetic: 500 µT, at 60 Hz in any direction
OMICRON 7
1.4 Standards
Table 1-20: Standards conformity
Safety
Safety IEC / EN / UL 61010-1
EMC
EMC IEC/EN 61326-1 (industrial electromagnetic environment)
FCC subpart B of part 15, class A
Other
Shock IEC 60068-2-27 (operating), 15 g/11 ms, half-sinusoid
Vibration IEC 60068-2-6 (operating), 10...150 Hz, acceleration 2 g
continuous (20 m/s2); 10 cycles per axis
Humidity IEC/EN 60068-2-78 (5…95 % relative humidity, no condensation)
8 OMICRON

CP TD12 15 Technical Data ENU

Uploaded by

Copyright:

Available Formats

CP TD12 15 Technical Data ENU

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CP TD12 15 Technical Data ENU

Uploaded by

Copyright:

Available Formats

CP TD12/15

© OMICRON electronics GmbH 2019. All rights reserved.

Terminal U THD I max S max t max

Table 1-2: CP TD15 – High-voltage output

Terminal U THD I max S max t max

Range Typical accuracy1

Filter for selective measurements

Filter Bandwidth Measurement time Stop band specification (attenuation)

Test current (RMS, selective)

Terminal Range Typical accuracy1 Conditions

Test voltage (RMS, selective)

Table 1-7: CP TD15 – Test voltage

Capacitance Cp (equivalent parallel circuit)

Range Typical accuracy1 Conditions

Dissipation factor DF (tan δ)

Range Typical accuracy1 Conditions

Power factor PF (cos ϕ )

Range Typical accuracy1 Conditions

2 f = 45...70 Hz, I < 8 mA,

0...100 % error < 0.5 % of reading + 0.02 % Utest = 2 kV...10 kV

Range Typical accuracy1 Conditions

Range Typical accuracy1 Conditions

Inductance Lx (equivalent serial circuit)

Range Typical accuracy1

Range Typical accuracy1

Range Typical accuracy1

Table 1-16: CP TD15 – Power P, Q, S

Range Typical accuracy1

0...4.5 kVAR2 error < 0.5 % of reading + 1 mVAR

0...4.5 kVA2 error < 0.5 % of reading + 1 mVA

1.2 Mechanical data

Table 1-17: Mechanical data

1.3 Environmental Conditions

Table 1-19: Noise Immunity

You might also like