Getting Started with 5G Mo-

dem Card
User Guide

1VV0301847 - Rev. 2
V.02
2024-2-23
Preliminary
Confidential

Technical Documentation
 Getting Started with 5G Modem Card User Guide
2

Contents
Contents........................................................................................................................................... 2
Tables ............................................................................................................................................... 3
Figures.............................................................................................................................................. 4
1 Applicability Table .................................................................................................................. 5
2 Introduction............................................................................................................................ 6
2.1 Scope .............................................................................................................................................. 6
2.2 Audience ........................................................................................................................................ 6
2.3 Contact Information, Support ................................................................................................... 6
2.4 Conventions .................................................................................................................................. 6
2.5 Terms and Conditions.................................................................................................................. 7
2.6 Disclaimer ...................................................................................................................................... 7
3 Getting Started with 5G Modem Cards.................................................................................. 8
3.1 Using USB Variant ........................................................................................................................ 8
3.1.1 Technical Requirements................................................................................................ 8
3.1.2 Connecting MV32-W to the 5G Modem Card Adapter Board ............................. 8
3.2 Using PCIe® .................................................................................................................................. 10
3.2.1 Technical Requirements.............................................................................................. 10
3.2.2 Connecting MV32-W to the 5G Modem Card Adapter Board ........................... 11
3.3 Modem Card Startup ................................................................................................................ 11
3.3.1 Script based Driver Installation on Windows 10/11 ............................................. 12
3.3.2 Setting up Linux Data Connection ............................................................................ 15
3.3.3 Setting up Windows Data Connection ..................................................................... 16
3.3.4 Reading MV32-W Properties ...................................................................................... 18
3.3.5 eSIM Provisioning.......................................................................................................... 19
3.3.6 GNSS Usage.................................................................................................................... 21
3.3.6.1 MV32: using the GNSS tool on WIN10/11............................................. 23
4 Appendix A............................................................................................................................ 26
4.1 5G Modem Card Adapter Board ............................................................................................ 26
4.1.1 Package Content of the USB Variant........................................................................ 26
4.2 5G Modem Card Adapter Board Description ..................................................................... 27
4.2.1 USB and PCIe® Variants ............................................................................................... 28
4.3 Power Supply Configuration .................................................................................................... 29
4.4 Configuration Switches ............................................................................................................. 29
4.5 Additional Connectors .............................................................................................................. 31
5 Document History ................................................................................................................ 32

1VV0301847 Rev. 2 Page 2 of 33 2024-2-23

33
 Getting Started with 5G Modem Card User Guide
3

Tables
Table 1: Applicability table ................................................................................................................ 5
Table 2: Driver Package Content................................................................................................... 12
Table 3: Power supply configuration............................................................................................ 29
Table 4: Signals at Jumper on J1025............................................................................................. 31
Table 5: Signals at Jumper on J1026............................................................................................. 31

1VV0301847 Rev. 2 Page 3 of 33 2024-2-23

33
 Getting Started with 5G Modem Card User Guide
4

Figures
Figure 1: 5G Modem Card.................................................................................................................. 9
Figure 2: MV32-W mounted on 5G Modem Card Adapter Board.......................................... 10
Figure 3: Script based driver installation ...................................................................................... 12
Figure 4: Devices before driver installation.................................................................................. 13
Figure 5: Devices after driver installation ..................................................................................... 13
Figure 6: Cellular properties ............................................................................................................ 14
Figure 7: Unlock SIM via Network connection............................................................................. 16
Figure 8: Providing SIM PIN.............................................................................................................. 16
Figure 9: PIN unlocked ...................................................................................................................... 17
Figure 10: Successful registration..................................................................................................... 17
Figure 11: Module’s properties ......................................................................................................... 18
Figure 12: Connecting with eSIM ...................................................................................................... 19
Figure 13: Operator selection............................................................................................................ 19
Figure 14: Connecting to an operator ............................................................................................. 20
Figure 15: Profile installation.............................................................................................................. 20
Figure 16: Network operator selection screen.............................................................................. 21
Figure 17: Sequence output............................................................................................................... 23
Figure 18: GNSS tool ............................................................................................................................ 24
Figure 19: 5G Modem Card Adapter Board Kit ............................................................................. 26
Figure 20: LTE Modem Card Adapter Board Jumper and Connectors .................................... 27
Figure 21: USB variant ......................................................................................................................... 28
Figure 22: PCIe variant......................................................................................................................... 28
Figure 23: U208..................................................................................................................................... 29
Figure 24: U209..................................................................................................................................... 30
Figure 25: U1120 .................................................................................................................................. 30
Figure 26: U206..................................................................................................................................... 30
Figure 27: U207..................................................................................................................................... 31

1VV0301847 Rev. 2 Page 4 of 33 2024-2-23

33
 Getting Started with 5G Modem Card User Guide
31

1 Applicability Table

Table 1: Applicability table

Products
MV32-W-A
MV32-W-B

1VV0301847 Rev. 2 Page 5 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

2 Introduction
2.1 Scope
This document describes a ready-to-use development and test environment for the Telit
Cinterion 5G Modem Card.
The development and test environment comprises the following hardware components
• 5G Modem Card MV32-W
• 5G Modem Card Adapter Board

The purpose of this document is to guide you through the process of connecting the hard-
ware, installing the supplied drivers on a Microsoft® Windows 10/11 system and getting
started with 5G Modem Card.

2.2 Audience
This document is intended for system integrators that are using the Telit MV32-W modules
in their products.

2.3 Contact Information, Support

For technical support and general questions, e-mail:
• [email protected]
• [email protected]
• [email protected]
• [email protected]
• [email protected]
Alternatively, use: https://www.telit.com/contact-us/
Product information and technical documents are accessible 24/7 on our website: https://
www.telit.com

2.4 Conventions
Note: Provide advice and suggestions that may be useful when integrating the mod-
ule.
Danger: This information MUST be followed, or catastrophic equipment failure or
personal injury may occur.
ESD Risk: Notifies the user to take proper grounding precautions before handling
the product.
Warning: Alerts the user on important steps about the module integration.
All dates are in ISO 8601 format, that is YYYY-MM-DD.

1VV0301847 Rev. 2 Page 6 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

2.5 Terms and Conditions

Refer to https://www.telit.com/hardware-terms-conditions/.

2.6 Disclaimer
THE MATERIAL IN THIS DOCUMENT IS FOR INFORMATIONAL PURPOSES ONLY. TELIT CIN-
TERION RESERVES THE RIGHT TO MAKE CHANGES TO THE PRODUCTS DESCRIBED HEREIN.
THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT THE DISCRETION
OF TELIT CINTERION WITHOUT PRIOR NOTICE. THIS DOCUMENT IS PROVIDED ON "AS IS"
BASIS ONLY AND MAY CONTAIN DEFICIENCIES OR INADEQUACIES. TELIT CINTERION DOES
NOT ASSUME ANY LIABILITY FOR INFORMATION PROVIDED IN THE DOCUMENT OR ARIS-
ING OUT OF THE APPLICATION OR USE OF ANY PRODUCT DESCRIBED HEREIN.
TELIT CINTERION GRANTS A NON-EXCLUSIVE RIGHT TO USE THE DOCUMENT. THE RECIP-
IENT SHALL NOT COPY, MODIFY, DISCLOSE, OR REPRODUCE THE DOCUMENT EXCEPT AS
SPECIFICALLY AUTHORIZED BY TELIT CINTERION.

TELIT CINTERION AND THE TELIT CINTERION LOGO, ARE TRADEMARKS OF TELIT CINTERI-
ON AND ARE REGISTERED IN CERTAIN COUNTRIES. ALL OTHER REGISTERED TRADEMARKS
OR TRADEMARKS MENTIONED IN THIS DOCUMENT ARE THE PROPERTY OF THEIR RESPEC-
TIVE OWNERS AND ARE EXPRESSLY RESERVED BY TELIT CINTERION (AND ITS LICENSORS).

1VV0301847 Rev. 2 Page 7 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3 Getting Started with 5G Modem Cards

3.1 Using USB Variant
3.1.1 Technical Requirements
• MV32-W sub6 USB (for details see Figure 1).
• Corresponding driver package (USB).
• Computer running Windows 10/11, USB 3.0 Interface.
• Local administrator privileges on the particular Windows computer to install and
uninstall the drivers.
• 5G Modem Card Adapter Board USB Variant (for details see Section 4.1).
• Accessories for sub6G USB variant of MV32-W:
• Four short 50 Ohms RF adapter cables with MHF4 type connectors to connect the
appropriate MHF4 type connectors on the 5G Modem Card Adapter Board (sup-
plied by Telit Cinterion)
• Four external 50 Ohms RF antennas with SMA connector to connect the SMA con-
nector on the 5G Modem Card Adapter Board (supplied by Telit Cinterion)
• USB 3.0 cable (supplied by Telit Cinterion)
• Appropriate application for controlling the module from within a PC’s operating sys-
tem. For Windows, e.g. Windows Hyperterminal
• (U)SIM from a UMTS/LTE/NR network provider

3.1.2 Connecting MV32-W to the 5G Modem Card Adapter

Board
To properly connect the 5G Modem Card and all accessories to the 5G Modem Card Adapt-
er Board please complete the steps listed below. The complete setup with the 5G Modem
Card mounted onto the 5G Modem Card Adapter Board is shown in Figure 2.

• Ensure that all jumpers and switches on the 5G Modem Card Adapter Board are set
to their positions as shown in Table 3 and switch USB/PCIe is in position USB (on).
• Place Thermo Pad with the self adhesive side (remove protection foil) on the 5G
Modem Card Adapter Board close to the M.2 connector.
• Insert the 5G Modem Card into the M.2 connector on the 5G Modem Card Adapter
Board and insert the screw to keep the 5G Modem Card in position and connected.
• Connect the MHF4 type connectors for the antennas on the 5G Modem Card
Adapter Board (ANT0, ANT1, ANT2, ANT3) to the matching MHF4 type connectors on
the 5G Modem Card.
• Screw the external antennas to the appropriate SMA connectors on the 5G Modem
Card Adapter Board (ANT0, ANT1, ANT2, ANT3).
• Insert the (U)SIM card into the card reader for 1st SIM.
• Plug the USB 3.0 USB cable to the USB jack at the 5G Modem Card Adapter Board.
After connecting the 5G Modem Card with the 5G Modem Card Adapter Board, the 5G Mo-

1VV0301847 Rev. 2 Page 8 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

dem Card can be switched on by connecting the other end of the USB cable to the PC. The
initial startup and possible USB driver installation are described in Section 3.3.
Top side
Pin 75

Antenna 3
LTE & 5G Sub 6 RX/GPS L1
mechanical ground pad

Antenna 2
LTE & 5G Sub 6 RX/TX

Antenna 1
LTE & 5G Sub 6 RX/GPS L5

Antenna 0
WCDMA
LTE & 5G Sub 6 RX/TX

Pin 1

Bottom side
Pin 2

Pin 74

Figure 1: 5G Modem Card

1VV0301847 Rev. 2 Page 9 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Figure 2: MV32-W mounted on 5G Modem Card Adapter Board

3.2 Using PCIe®

3.2.1 Technical Requirements
• MV32-W sub6 PCIe (for details see Figure 1).
• Corresponding driver package (PCIe).
• Computer running Windows 10/11, PCIe M.2 Interface.
• Local administrator privileges on the particular Windows computer to install and
uninstall the drivers.
• 5G Modem Card Adapter Board PCIe Variant (for details see Section Section 4.1).
• Accessories for sub6G PCIe variant of MV32-W:
• Four short 50 Ohms RF adapter cables with MHF4 type connectors to connect the
appropriate MHF4 type connectors on the 5G Modem Card Adapter Board (sup-
plied by Telit Cinterion).
• Four external 50 Ohms RF antennas with SMA connector to connect the SMA con-
nector on the 5G Modem Card Adapter Board (supplied by Telit Cinterion) .
• Appropriate application for controlling the module from within a PC’s operating sys-
tem. For Windows, e.g. Windows Hyperterminal.
• (U)SIM from a UMTS/LTE/NR network provider.

1VV0301847 Rev. 2 Page 10 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3.2.2 Connecting MV32-W to the 5G Modem Card Adapter

Board
To properly connect the 5G Modem Card and all accessories to the 5G Modem Card Adapt-
er Board please complete the steps listed below. The complete setup with the 5G Modem
Card mounted onto the 5G Modem Card Adapter Board is shown in Figure 3.

• Ensure that all jumpers and switches on the 5G Modem Card Adapter Board are set
to their positions as shown in Table 3 and switch USB/PCIe is in position PCIe (off).
• Place Thermo Pad with the self adhesive side (remove protection foil) on the 5G
Modem Card Adapter Board close to the M.2 connector.
• Insert the 5G Modem Card into the M.2 connector on the 5G Modem Card Adapter
Board and insert the screw to keep the 5G Modem Card in position and connected.
• Connect the MHF4 type connectors for the antennas on the 5G Modem Card
Adapter Board (ANT0, ANT1, ANT2, ANT3) to the matching MHF4 type connectors on
the 5G Modem Card.
• Screw the external antennas to the appropriate SMA connectors on the 5G Modem
Card Adapter Board (ANT0, ANT1, ANT2, ANT3).
• Insert the (U)SIM card into the card reader on your host device.
• Plug the M.2 Adapter Card into your PC

After connecting the 5G Modem Card with the 5G Modem Card Adapter Board, the 5G Mo-
dem Card can be switched on by switching on your PC. The initial startup and possible PCIe
driver installation are described in Section 3.3.

3.3 Modem Card Startup

After connecting the 5G Modem Card to the 5G Modem Card Adapter Board as described
in Section 3.1.2, the 5G Modem can be used.

Note:
The driver package provided by Telit Cinterion needs to be available. Extract and Copy the
supplied driver files to a folder on the Windows computer. Be sure to use the latest driver
software supplied by Telit Cinterion.
The driver package depends on the interface of the MV32-W Variant (USB or PCIe) and con-
tains all the drivers needed for this variant MV32-W (see Table 2).

1VV0301847 Rev. 2 Page 11 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Table 2: Driver Package Content

Driver Installation Starter Kit connected MV32-W connected via PCIe M.2 or
sequence via USB3.0 PCIe Edge Connector
Directory Directory
MHI 1 not required - required \MHI
UDE 2 not required - required \UDE
QUD 3 required \QUD_GNS required \QUD_GNSS
S
GNSS 4 required \QUD_GNS required \QUD_GNSS
S

3.3.1 Script based Driver Installation on Windows 10/11

The drivers can be installed via script. Therefore connect the Starter Kit with your PC first.
Then run as "Administrator" the file "install_mv32_drivers.cmd", which is provided with the
driver package. When unpacking the driver package, don’t use space character in the folder
path.
After running the script the interfaces shown in Table 3 for USB or Table 3 for PCIe should
be installed.

Figure 3: Script based driver installation

1VV0301847 Rev. 2 Page 12 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Once windows drivers have been installed with the script, then MV32-W is shown as follow-
ing devices under Device Manger on Windows 10/11:

Figure 4: Devices before driver installation

Figure 5: Devices after driver installation

After the windows driver installation, Windows 10/11 will automatically setup mobile net-
work under "Settings ->Network & Internet ->Cellular":

1VV0301847 Rev. 2 Page 13 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Next, please check the cellular properties:

Figure 6: Cellular properties

1VV0301847 Rev. 2 Page 14 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3.3.2 Setting up Linux Data Connection

This section explains how to set up Linux data connection.
• Please make sure ports look as presented below:

• Start mbim with the following command: mbim-network /dev/cdc-wdm1 start

• Request IP address:

• Check the network interface IP address:

• Test data connection with ping:

1VV0301847 Rev. 2 Page 15 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3.3.3 Setting up Windows Data Connection

The following steps will show how to enter the SIM PIN for going Online with MV32-W:
1. When the used SIM is locked by a PIN, Windows 10/11 will inform you, that the PIN is
required. Click on this message or go to "Network Connections" (Click on "Start" with
left mouse button and select "Network connection", "Cellular" (1) and then "Unlock
SIM" (2).

Figure 7: Unlock SIM via Network connection

2. Enter your PIN

Figure 8: Providing SIM PIN

1VV0301847 Rev. 2 Page 16 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3. After entering the PIN press button "Next"

Figure 9: PIN unlocked

4. After successful registration to the network Windows 11 will show "Connected"

Figure 10: Successful registration

Now you can open an Internet Browser and go Online.

1VV0301847 Rev. 2 Page 17 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3.3.4 Reading MV32-W Properties

To read the properties (Firmware version, IMEI, ...) of MV32-W go to "Network Connections"
(Click on "Start" with left mouse button and select "Network connection" and then, "Cellu-
lar" (1). Under "Advanced Option" (2) the firmware version of the MV32-W will be shown.

Figure 11: Module’s properties

Additionally, “Metered Connection”, “APN settings” can be configured and the SIM PIN can
be changed or removed too.

1VV0301847 Rev. 2 Page 18 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

3.3.5 eSIM Provisioning

MV32-W has an eSIM default on board.
Provisioning of the eSIM can be done via the Mobile Plans APP on Microsoft Windows 10/
11.
Use the AT command AT+SWITCH_SLOT=1 to switch to the internal eSIM
On Windows 10/11, under "Setting->Network & internet->Cellular" , chose "connect with
eSIM"

Figure 12: Connecting with eSIM

Open the "Mobile Plans" app and select an operator.

Figure 13: Operator selection

1VV0301847 Rev. 2 Page 19 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Figure 14: Connecting to an operator

Click on "Get connected" and follow Windows 10/11 installation instructions:

Figure 15: Profile installation

1VV0301847 Rev. 2 Page 20 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Note:
eSIM profiles provided by other network operators can be chosen as well:

Figure 16: Network operator selection screen

3.3.6 GNSS Usage

MV32 has the GNSS function with the features:

• GPS, GLONASS, Galileo, and BeiDou support integrated in chipset.

• Two GNSS paths to support simultaneous L1 and L2/L5.
• Customizable tracking session
• Automatic tracking session on startup,
• Concurrent standalone GPS, GLONASS , BeiDou and Galileo,
• gpsOneXTRA with GPS + GLONASS + BeiDou+ Galileo support.

On WIN10/11, there are interfaces of MBIM network, ports: NMEA/GNSS, DIAG, MODEM.

1VV0301847 Rev. 2 Page 21 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

MV32: AT command for GNSS control

• AT+GPS: check the status of GPS engine
• AT+GPS_START: to start GPS
• AT+GPS_INFO: Get TTFF and CN information
• AT+GPS_STOP; to stop GPS

Note:
MV32 can use the Xtra file. e.g from QCT gpsOne XTRA Daemon.
Example:
AT+GPS?
1
OK

AT+GPS_INFO
GPS has not start.....
OK

AT+GPS_START=2
Hot Start Success!
OK

1VV0301847 Rev. 2 Page 22 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

AT+GPS_INFO
GPS_CN:34.299999
GPS_TTFF:2.699000

OK

MV32: NMEA sequence output at the NMEA port with baud rate = 57600

Figure 17: Sequence output

3.3.6.1 MV32: using the GNSS tool on WIN10/11

Note:
A SW tool GNSS can be used on WIN10/11, for GNSS testing and data view

1VV0301847 Rev. 2 Page 23 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Figure 18: GNSS tool

1VV0301847 Rev. 2 Page 24 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Note:
1) the NMEA output is started with AT+GPS=1,
2) the NMEA output is stopped with AT+GPS=0
3) the NMEA output is there in every second
4) the NMEA sequences follow the 0183 V4.x standard Norm as from year 2012/2018

MV32-W requires a reboot after executing the following commands:

AT+GPS=1
AT+GPS=0

1VV0301847 Rev. 2 Page 25 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

4 Appendix A
4.1 5G Modem Card Adapter Board
4.1.1 Package Content of the USB Variant

Figure 19: 5G Modem Card Adapter Board Kit

The 5G Modem Card Adapter Board (Figure 19 A) will be delivered together with
• 1 USB 3.0 cable (Figure 19 B)
• 1 USB cable with USB-C connector (Figure 19 C)
• 4 MHF4 type antenna cables (Figure 19 D)
• 4 UMTS/LTE/NR antennas (Figure 19 E)
• 1 Thermal Pad (Figure 19 F)
• 1 Screw to fix M.2 Card (Figure 19 G)
• 4 MHF4 to SMA antenna cables including washers and nuts (Figure 19 H)
GNSS Antenna and Power supply are not part of the 5G Modem Card Adapter Board deliv-
ery.
Ordering Number: L30960-N6903-A100
Antenna Manufacturer Name: WHA YU Industrial Co LTD, Taiwan
Antenna part number: WHA_YU_C107-511818-A

1VV0301847 Rev. 2 Page 26 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

4.2 5G Modem Card Adapter Board Description

PCIe Interface 2nd SIM 1st SIM J9 Body SAR RESET PCIe M.2
(Golden Finger) Interface Interface Interface
J1013 J1026
(Debug)
SIM

ON OFF
USB2.0
ANT0 (Debug)

LED1
POWER
ANT1
USB3.0

ANT2
J6
J7
ANT3
1
USB-C
1 2
1

OFF ON

5G Modem Card U208 LTE Power GPS DPR PCIe/USB J10 J1025
MV32-W Enable On Enable Enable (Debug)
(to be attached)

Figure 20: LTE Modem Card Adapter Board Jumper and Connectors

1VV0301847 Rev. 2 Page 27 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

4.2.1 USB and PCIe® Variants

Figure 21: USB variant

Figure 22: PCIe variant

1VV0301847 Rev. 2 Page 28 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

4.3 Power Supply Configuration

The 5G Modem Card Adapter Board can be powered over USB (USB 3.0 and USB-C), PCIe
interface or by an external power supply. For configuration see Table 2

Table 3: Power supply configuration

No J1 J2 J3 J4 J5
1 Powered by USB3.0 mounted mounted mounted removed removed
2 Powered by USB3.0 mounted mounted mounted removed mounted
and USB-C
3 Powered by PCIe removed mounted mounted mounted removed
Interface (Golden Fin-
ger or PCIe M.2)
4 Powered external removed inject PIN1 mounted removed removed
3.3V

For the position of the Jumpers see Figure 20.

4.4 Configuration Switches

The following figures show the recommended switch configuration.

Slide Pins 4 and 7 to on. Select UART

Slide Pin 3 to on. Enable mmW Ant 4

Pin 1

Figure 23: U208

Note:
When you slide pins 4 and 7, the opposite pins should not slide in the same direction.

1VV0301847 Rev. 2 Page 29 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Pin 1

Slide pin 3 to on.

Enable mmW Ant3

MIPI:
Option 1: Slide pins 5 and 8 to on
Option 2: Slide pins 6 and 7 to on

Figure 24: U209

Tuner IC:
Default: Slide pin1-pin8 to off, Tuner IC is off.
Optional: Slide pin1-pin8 to on, Tuner IC is on.

Figure 25: U1120

Pin 1

Default: Slide Pin4 to on, Power=3.3V

Slide Pin8 to on. Enable mmW Ant1

Figure 26: U206

1VV0301847 Rev. 2 Page 30 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
31

Pin 1

Slide Pin5 to on. Enable mmW Ant2

Slide Pin8 to on. Enable mmW Ant1

Figure 27: U207

4.5 Additional Connectors

J1025 (Table 4) and J1026 (Table 5) provide additional signals, which are not available at the
standard interfaces. For the position of J1025 and J1026 see Figure 20.

Table 4: Signals at Jumper on J1025

Signal J1025 Signal

1 2 RFFE2_DATA
PCM_OUT 3 4 RFFE2_CLK
PCM_CLK 5 6 SDR_GRFC2
SDX_DBG_UART_RX 7 8 COEX_UART_RX
SDX_DBG_UART_TX 9 10 COEX_UART_TX

Table 5: Signals at Jumper on J1026

Signal J1026 Signal

1 2 FULL_CARD_POWER_OFF
RFFE2_CLK 3 4 RESET#
RFFE2_DATA 5 6 PERST#
CLKREQ# 7 8 REFCLKn
PEWAKE# 9 10 REFCLKp

1VV0301847 Rev. 2 Page 31 of 33 2024-2-23

 Getting Started with 5G Modem Card User Guide
32

5 Document History

Preceding document: “Getting Started with 5G Modem Card”, Version 02 Rev 1

New document: “Getting Started with 5G Modem Card”, Version 02 Rev 2
Chapter What is new
3.3.6 New section added.

Preceding document: “Getting Started with 5G Modem Card”, Version 02 Rev 0

New document: “Getting Started with 5G Modem Card”, Version 02 Rev 1
Chapter What is new
3.3.4 Figure 11 updated.

Preceding document: “Getting Started with 5G Modem Card”, Version 01

New document: “Getting Started with 5G Modem Card”, Version 02
Chapter What is new
Throughout Distinguish between USB and PCIe M.2 variant of Starter Kit
document
Added chapter for PCI driver installation
Chapter revised. Configuration description added.

New document: “Getting Started with 5G Modem Card”, Version 01

Chapter What is new
-- Initial document setup.

1VV0301847 Rev. 2 Page 32 of 33 2024-2-23

© Telit All rights reserved.
33
Technical Documentation