Chandan

SMART ATM CARD FOR MULTIPLE BANK ACCOUNTS
USING RFID
Submitted in partial fulfillment of the requirements for the award of Bachelor
of Engineering Degree in Electronics and Communication Engineering
by
C.MADHUMITHA (38130121)
C.SELVALAKSHMI (38130200)
DEPARTMENT OF ELECTRONICS AND COMMUNICATION

ENGINEERING
SCHOOL OF ELECTRICAL AND ELECTRONICS
SATHYABAMA
INSTITUTE OF SCIENCE AND TECHNOLOGY
(DEEMED TO BE UNIVERSITY)
Accredited with Grade “A” by NAAC I 12B Status by UGC I Approved by AICTE
JEPPIAAR NAGAR, RAJIV GANDHI SALAI, CHENNAI - 600 119
APRIL 2022
SATHYABAMA
INSTITUTE OF SCIENCE AND TECHNOLOGY
(DEEMED TO BE UNIVERSITY)
Accredited with ‘A’ grade by NAAC | 12B status by UGC | Approved by AICTE
Jeppiar Nagar, Rajiv Gandhi salai, Chennai-600 119
www.sathyabama.ac.in
DEPARTMENT OF ELECTRONICS AND COMMUNICATION

ENGENEERING
BONAFIDE CERTIFICATE
This is to certify that this Project Report is the bonafide work of MADHUMITHA C
(38130121) and SELVALAKSHMI C (38130200) who carried out project entitled” SMART
ATM CARD FOR MULTIPLE BANK ACCOUNTS” under our supervision from October
2021 to April 2022.
.
Internal Guide
Dr. R. JOANY, M.E, Ph.D.,
Head of the Department
Dr. T. RAVI, M.E., Ph.D.,
Submitted for Viva voce Examination held on
Internal Examiner External Examiner
II
DECLARATION
We MADHUMITHA C (38130121) and SELVALAKSHMI C (38130200) hereby declare that

the Project Report entitled “SMART ATM CARD FOR MULTIPLE BANK ACCOUNTS –
USING RFID “done by us under the guidance of Dr. R. JOANY, M.E, Ph.D., is submitted in
partial fulfilment of the requirements for the award of Bachelor of Engineering degree in
Electronics and Communication Engineering.
1)
2)
DATE:
PLACE: SIGNATURE OF THE CANDIDATES
III
ACKNOWLEDGEMENT
We are pleased to acknowledge my sincere thanks to Board of Management of

SATHYABAMA for their kind encouragement in doing this project and for completing it
successfully. I am grateful to them.
We convey our thanks to Dr. N.M. NANDHITHA, M.E, Ph.D., Dean, School of
Electronics and Communication Engineering and Dr. T. RAVI, M.E, Ph.D., Head of
the Department, Department of Electronics and Communication Engineering for
providing me necessary support and details at the right time during the progressive
reviews.
We would like to express my sincere and deep sense of gratitude to my Project Guide
Dr. R.M. Joany, M.E, Ph.D., for her valuable guidance, suggestions and constant
encouragement paved way for the successful completion of my project work.
We wish to express my thanks to all Teaching and Non-teaching staff members of the
Department of Electronics and communication Engineering who were helpful in
many ways for the completion of the project.
We express our gratitude to our parents for their continuous encouragement and
support for the completion of the project.
IV
ABSTRACT
ATM is an abbreviation of Automated Teller Machine. It is introduced in the year

1959 for encouraging self-service in retail banking. This makes people to deposit,
withdraw and transfer amount without the help of banking personnel’s and it can be
done at anytime and anywhere. At first, the ATM was made to transact for the particular
bank customers but later on the ATM are connected to inter-bank network, so that it
enables people to deposit, withdraw and transfer amount from the ATM machines not
belonging to that particular bank (i.e.) any one can access any banks ATM machine to
carry out their transactions. ATM's rely on authorization of a financial transaction by
the card issuer or other authorizing institution via the communication network. This is
often performed through an ISO 8583messaging system. Many bank charges ATM
usage fees from the customers for the transactions. At present every customer has an
individual ATM card for each and every bank in which he/she maintains account. So
handling the cards, their passwords play a major role here. So to overcome these
difficulties we embedded more than one bank account of the user in a single ATM
smart card, so that the user can swipe the card and can select the bank from which
he/she are interested to carry out transaction.
V
TABLE OF CONTENT
CHAPTER NO. TITLE PAGE NO
ABSTRACT V
LIST OF FIGURES VIII
LIST OF TABLES X
LIST OF ABBREVIATIONS XI
CHAPTER NO TITLE PAGE NO
1 INTRODUCTION 1
1.1 GENERAL 1
1.2 SCOPE OF THE PROJECT 1
1.3 EXISTING SYSTEM 1
1.4 EXISTINGSYSTEM DISADVANTAGES
2 LITERATURE SURVEY 2
2.1 LITERATURE SURVEY 2
2.2 LITERATURE SUMMARY 5
3 AIM AND SCOPE OF THE PRESENT

INVESTIGATION 6
3.1 PROPOSED SYSTEM 6

3.1.1 PROPOSED SYSTEM ADVANTAGES 6
3.2 BLOCK DIAGRAM 6
3.3 MODULES NAME 7
3.4 MODULE DESCRIPTION 7
3.4.1 RFID IDENTIFICATION 7
3.4.2 BIOMETRIC AUTHENTICATION 8
3.4.3 TRANSACTION PROCESS 8
3.4.4 ALERT MODULE 9
3.5 BLOCK DIAGRAM DESCRIPTION 9
VI
4 MATERIALS AND METHODS USED
4.1 HARDWARE DESCRIPTION 10

4.1.1 ARDUINO 10
4.1.1.1 ARDUINO MEGA 12
4.1.2 GSM 25
4.1.2.1 FUNCTIONAL DESCRIPTION 28
4.1.3 POWER SUPPLY 29
4.1.4 RFID READER AND TAG 37
4.1.5 KEYPAD 39
4.1.6 LCD 42
4.1.7 FINGERPRINT SENSOR 46
4.1.7.1 OPERATION PRINCIPLE 47
4.1.7.2 FEATURES 47
4.1.8 BUZZER 53
4.1.8.1 BUZZER FEATURES & SPECIFICATIONS 53
4.1.9 SERVOMOTOR 54
4.1.9.1 FEATURES AND APPLICATIONS 56
4.1.9.2 SERVO MOTOR WORKING PRINCIPLE 57
4.2 SOFTWARE DESCRIPTION 59
4.2.1 EMBEDDED C 59
4.2.2 ARDUINO SOFTWARE IDE 59
5 RESULT AND DISCUSSION
5.1 OUTPUT 69
6 CONCLUSION AND FUTURE WORKS
6.1 CONCLUSION 81
6.2 ADVANTAGES 81
6.3 APPLICATIONS 82
6.4 FUTURE ENHANCEMENTS 82
REFERENCE 83
VII
LIST OF FIGURES
CHAPTER NO. TITLE PAGE NO
3.1 Block diagram 6

3.2 RFID identification 7
3.3 Biometric authentication 8
3.4 Transaction process 8
3.5 Alert module 9
4.1 Arduino mega board 12
4.2 Arduino mega 13
4.3 Ultrasonic sensor code 16
4.4 Arduino Mega 2560 PIN diagram 18
4.5 Power supply diagram 25
4.6 GSM module 26
4.7 System block diagram 27
4.8 Keypad connection SIM 32
4.9 SIM connection (no power control) 33
4.10 MIC input (differential input) 36
4.11 MIC input (single-ended input) 36
4.12 RFID reader 38
4.13 RFID card 38
4.14 Application circuit 39
4.15 Keypad 40
4.16 LCD 42
4.17 Data register 45
4.18 Finger print sensor 46
4.19 Hardware interface 48
4.20 Servo motor 58
4.21 block diagram representation of embedded system 59
4.22 block diagram of Embedded C Programming development 60
5.1 Overall circuit Connections 69
5.2 Using RFID Tag 69
VIII
5.3 Using Fingerprint sensor 70
5.4 Registration of fingerprint 70
5.5 Finger print sensor 70
5.6 Mobile no Registration process 71
5.7 Keypad 71
5.8 Mobile number Registration process 72
5.9 Mobile Number Access 72
5.10 Registering our Mobile Number 72
5.11 Otp is generated 73
5.12 Received otp 73
5.13 Enter the otp 74
5.14 Verification of otp 74
5.15 Deposit 74
5.16 Biometric process 75
5.17 Deposit 75
5.18 Selecting SBI bank(1) 75
5.19 Widraw 76
5.20 Select the Bank 77
5.21 Enter the Amount 77
5.22 Withdrawal amount and Balance 77
5.23 Checking BAL 78
5.24 view Balance 78
5.25 Place Finger 79
5.26 Fraud Access 79
5.27 Mismatched finger print 79
5.28 Un authorized 80
5.29 messages to the registered mobile number 80
IX
LIST OF TABLES
CHAPTER NO TITLE PAGE NO
4.1 Technical Specifications 13

4.2 Arduino Mega 2560 PIN mapping table 18
4.3 Product Description 27
4.4 VBAT Pin Description 29
4.5 GND Pin Description 29
4.6 Power consumption in OFF mode 30
4.7 Power consumption in EGSM 900MHZ 30
4.8 Power consumption in DCS/PCS 1800MHZ 30
4.9 VCC Pin Description 31
4.10 SPI Pin Description 31
4.11 SIM Interface 32
4.12 Audio Interface 34
4.13 Microphone Electrical Characteristics 34
4.14 Speaker Electrical Characteristics 35
4.15 Pin detail of LCD display 43
4.16 Important Command Codes for LCD 45
4.17 Serial communication pin details 49
4.18 USB Communication 49
4.19 Buzzer Pin Configuration 53
X
LIST OF ABBREVIATION
1. ATM - Automatic Teller Machine

2. RFID - Radio Frequency Identification
3. GSM - Global System for Mobile Communication
4. LCD - Liquid Crystal Display
5. IOT - Internet of Things
6. CLK - Clock
7. SIM - Subscriber Identity Module Card
8. CPU - Central Processing Unit
9. PIN - Personal Identification Number
10. LED - Light Emitting Diode
11. IDE - Integrated Development Environment
12. USB - Universal Server Bus
13. RAM - Random Access Memory
14. ROM - Read Only Memory
15. ADC - Analog to Digital Convertor
16. DAC - Digital to Analog Convertor
17. AVR - Automatic Voltage Regulation
18. TMS - Transportation Management System
19. SCL - System Check List
20. SPI - Schedule Performance Index
21. PCB - Printed Circuit Board
22. GPIO - General Purpose Input/Output
23. TXD - Serial Data Transmit Pin
24. RXD - Serial Data Receive Pin
25. SCI - Serial Communication Interface
26. UART - Universal Asynchronous Receiver- Transmitter
XI
CHAPTER 1
INTRODUCTION
1.1 GENERAL
An automated teller machine (ATM) is an electronic banking outlet that allows

customers to complete basic transactions without the aid of a branch representative
or teller. Anyone with a credit card or debit card can access cash at most ATMs.
ATMs are convenient, allowing consumers to perform quick self-service

transactions such as deposits, cash withdrawals, bill payments, and transfers
between accounts. Fees are commonly charged for cash withdrawals by the bank
where the account is located, by the operator of the ATM, or by both. Some or all of
these fees can be avoided by using an ATM operated directly by the bank that holds
the account.
1.2 SCOPE OF THE PROJECT
The main aim of the project is to eliminate several ATM cards and to replace it
with a single card which can be interfaced with multiple banks. This reduces the cards
if multiple accounts are present.
1.3 EXISTING SYSTEM
In the existing system, when the user enters the ATM system the user has to
insert the respective card of the user’s choice into the ATM system’s card slot. The
next immediate step the user has to do is enter the pin for that particular card. There
are multiple cards if the user has bank accounts and there is a possible chance of
entering PIN’s of other cards which may affect the transaction process.
1.3.1 EXISTING SYSTEM DISADVANTAGES

 Multiple Cards
 Security of ATM card is less
1
CHAPTER 2
LITERATURE SURVEY
2.1 LITERATURE SURVEY
Title 1: ATM Security using GSM technology.
Authors: Sudhakar Hallur,Manjunath Bajantri, Sagar.
Year: 2018
Description
Automated Teller Machine (ATM)’s now a days are extensively used all over
the world for the withdrawal of cash. A unique card is issued for each user along with
the unique code provided to him so as to the person may do all his transactions
personally without anyone getting known. Since transactions are extensively secure
there is no much more security required but in countries like India it’s very necessary
to have a physical security to the machine. A provision to give physical security to the
machine is being discussed over here in this paper presented over here.
Title 2: Implementation of Bank Security System using GSM and Internet of Things
Authors: Moturi Phalguna Satish, Bala Kishore. G
Year: 2017
Description
The Internet of Things (IoT) is one of the hottest topics in the technology sector,
and with good reason. It influences the interaction of technological, economic, social,
societal, and individual changes. Internet of things has been governing the electronics
era with cloud services dominating the ever increasing electronics product segment.
Security and safety has always become a basic necessity for urban population. The
Implementation of the Bank Security System by Using GSM and IoT is developed into
the security application. The main objective of this system is to develop an embedded
system, which is used for ATM security applications. The embedded ATM
authentication system is based on sensors & communication technology. In this paper
2
when any disturbance takes place for the ATM machine then information is send
through IoT and door is automatically closed then it will send the machine, by alerting
the surrounding area using buzzer, at the same time total data will be uploaded in web
page using IoT and puts alert message to consult person. In the same way if any fire
occurred controller puts a message to consult person and uploads same data in web
page using IoT. It also counts how many persons are entering into the ATM centre.
This concept is not only a single ATM center; we can consider this ATM center as
node1 (like node1, node2, node3……. Etc) are connected to web page through IoT
module (ESP 8266). So that if there is any disturbance or any fire accident in any
node we can get the area information through IoT to the web page along with buzzer.
Title 3: Advanced Security Management System for ATM's using GSM and MEMS
Authors: Venka Reddy Maram, Mirza Sajid Ali Baig, Narsappa Reddy.
Year: 2015
Description
Security in ATM networks is necessary because ATM is widespread and many

areas such as financial- or medical-applications, network-administration, etc. require
very sensitive handling of the transmitted data. If we look at other fields of interest
(only multimedia technologies and cable television shall be mentioned among others)
we see that ATM channels might be used for billing. Misuse of the ATM network,
manipulation of transmitted data, spoofing, or repudiation would be fatal in billing-
/accounting-system. Robberies of ATM‟s, misusage of credit cards and all. Our
project is going to concentrate on the ATM security system. Whenever a thief enters
and tries to touch an ATM forcefully. The movement will be observed by the MEMS
sensor. While MEMS observe the movement it sends a request to the microcontroller.
Microcontroller will automatically lock the door which is represented with the help of
DC motor and send a message to the authority through GSM. It will produce sound
with the help of buzzer to alert the security. And this door will be unlocked with the
switch which is present outside the room.
3
Title 4: ATM machine security system using GSM and MEMS sensor
Authors: Prof.Shinde S.P, Chingale R.R., Dhane D.C.,Vader P.B.
Year: 2017
Description
The Idea of Designing and of Security Based ATM machine security system
project is born with the observation in our real life examples happening around us.
This project overcomes the drawback of older technology used in our society. Project
deals with the security of ATM machine. Whenever robbery occurs, Vibration sensor
and MEMS sensor is used here which senses vibration produced from ATM machine
and the movement of ATM machine. GSM is used to send the message to the police
station and authority. In this project we uses PIC controller which is based on
embedded system process real time data collected using the MEMS sensor and
vibration sensor. When the movement of machine and the vibration is sensed the
beep sound will occur from the buzzer. For closing the door of ATM DC Motor is used.
Smoke detector is used here to sense the gaseous or smoke near ATM machine. The
use of camera is always in processing and sending video continuous to the Pc and it
will be saved. Here LCD display board shows the status of our project. It will prevent
the robbery occur. Here, MPLAB tools are used to implement the idea and results are
obtained. MPLAB tools are used for run the DC motor for automatic door lock.
Title 5: Advance Security System for ATM
Authors: Aman Kumar.
Year: 2015
Description
In present time ATM (Automatic Teller Machine) robbery is the common thing,
because we have not strong security and rule or regulation to withdraw the cash from
ATM with help of ATM card. In this paper I have provide the solution of robbery of
ATM to use various technology, rules and regulation. This is common weakness in
ATM security facility, remove this problem we used following technology to improve
security system .This technology work in main three steps or phases, in first phase
4
user need to swap the ATM and used palm for scanning after successfully swap
machine will generate voice you can enter for 2nd phase and palm will save in that
transaction database. When you go for 2nd phase then need to scan the retina and
then go for phase 3rd. there will final ATM. In performing the transaction gate will
closed. The wall of phases will of strong fiber that cannot cut by any Gas. The final
phase has Gas that can power for unconscious. And all CCTV cameras monitored by
near police station. When any thief does robbery in ATM then alarm generate in police
station and Gas will leak in near ATM. Then in this situation all information like,
robbery time, date, CCTV data, voice data will stored in server. The server monitored
by state level. This paper shows only how three phases will work and generate alarm
in near police station & send police in robbery situations.
2.2 LITERATURE SUMMARY
As we have mentioned in the above literature surveys in the past years ,There is
gradual development in the accessibility of ATM card and necessity of improving the
user friendly and Secure domain in the ATM cards and It evolving method of using it
for multiple bank accounts So, We have initiated the Fingerprint Security for out
Project in order to differentiate and stand alone from the previous projects The
fingerprint technology is the most widely accepted and mature biometric method and
is the easiest to deploy and for a higher level of security at your fingertips. It is simple
to install and also it takes little time and effort to acquire one’s fingerprint with a
fingerprint identification device .
Thus, finger print recognition is considered among the least intrusive of all
biometric verification techniques. The finger print features are different for each
human being so the user can be identified uniquely. Instead of using multiple ATM
card fingerprint based ATM is safer and secure. There is no worry of losing ATM
card and no need to carry ATM card in your wallet. We just have to use our
fingerprint in order to do any banking transaction.
CHAPTER 3
AIM AND SCOPE OF THE PRESENT INVESTIGATION
5
3.1 PROPOSED SYSTEM
The proposed scheme of MAASC (Multiple Account Access using Single ATM
Card) provides the individual, the comfort of accessing users multiple accounts of
different banks using a single card. Also, it provides the user one level higher
convenience than the existing system. The transactions are approved by biometric
authentication of the user which is replaced instead of PIN. As the bank server are
different so the linking of single card to multiple server won’t be a tough process.
3.1.1 PROPOSED SYSTEM ADVANTAGES
• Single ATM card provides more convince of using multiple bank transactions
• Higher security based on the biometric module
• More secure transaction using biometric of the user.
3.2 BLOCK DIAGRAM
POWER SUPPLY
LCD
GSM
FINGERPRINT RFID READER

SENSOR
ARDUINO
MEGA RFID TAG (2)
BUZZER
KEYPAD
SERVO MOTOR
Fig 3.1: Block diagram
3.3 MODULES NAME

 RFID Identification
 Biometric Authentication
6
 Transaction Process
 Alert Module
3.4 MODULE DESCRIPTION

In this project four modules are there.
They are:
 RFID identification
 Biometric module
 Transaction process
 Alert module
3.4.1 RFID IDENTIFICATION
POWER SUPPLY
RFID READER
ARDUINO LCD
MEGA
RFID TAG
Fig 3.2: RFID IDENTIFICATION
This module which is used to identify the user of the ATM through RFID tag ans
reader.The user of the ATM is identified using this instead of magnetic strips that is
being used in the existing method. This is displayed in the LCD. The
Microcontroller controls the overall process of this system.
7
3.4.2 BIOMETRIC AUTHENTICATION
The biometric authentication is one of the feature where the security is enhanched.
After The user of the ATM card ensures their identity by RFID followed by their
biometric to continue the transaction process. If the biometric and the RFID matches
then the user interface of the prototype directs the user to select the bank to which
they have been registered.
POWER SUPPLY
FINGERPRINT
SENSOR ARDUINO LCD
MEGA
Fig 3.3: BIOMETRIC AUTHENTICATION
3.4.3 TRANSACTION PROCESS
POWER SUPPLY
KEYPAD
ARDUINO
LCD
MEGA
GSM
Fig 3.4: TRANSACTION PROCESS
After the authenticaiton process the user is directed to select the bank that the user
have already registered. The user can use the keypad to select the bank according to
the banks displayed in the LCD. The transaction process is the same as the normal
ATM after the selection of the bank. The balance, debit and credit status is displayed
in the LCD so that user can select it to this convienence.
8
3.4.4 ALERT MODULE
POWER SUPPLY
BUZZER LCD
ARDUINO
MEGA
SERVOMOTOR
Fig 3.5: ALERT MODULE
If there is any mismatch in the rfid or the biometric then the alarm is triggered
through the microcontroller and a warning message is displayed in the LCD and same
is sent as a SMS to the user of the card. If the authentication process is successful,
then after the transaction process a servomotor is triggered to show the transaction is
successful and a SMS is also sent to the user about the transaction and balance.
3.5 BLOCK DIAGRAM DESCRIPTION AND WORKING
In the proposed method, the magnetic strip based ATM card is replaced with RFID
based card which have a unique number. The Arduino MEGA microcontroller is used
to process the data from the sensor. The fingerprint module is used to authenticate the
user and the user needs to enter the One Time Password (OTP) which is generated
by the controller and it is sent to the registered user mobile phone. The user can
register the bank details and also withdraw the amount from the registered bank
details. Hence this system provides more secure and multiple bank account using
single ATM card.
9
CHAPTER 4
MATERIALS AND MATHOD USED
4.1 HARDWARE DESCRIPTION:
4.1.1 ARDUINO
Arduino is an open-source electronics platform based on easy-to-use hardware

and software. Arduino boards are able to read inputs - light on a sensor, a finger on a
button, or a Twitter message - and turn it into an output - activating a motor, turning
on an LED, publishing something online. You can tell your board what to do by
sending a set of instructions to the microcontroller on the board.
Over the years Arduino has been the brain of thousands of projects, from
everyday objects to complex scientific instruments. A worldwide community of makers
- students, hobbyists, artists, programmers, and professionals - has gathered around
this open-source platform, their contributions have added up to an incredible amount
of accessible knowledge that can be of great help to novices and experts alike.
Arduino was born at the Ivrea Interaction Design Institute as an easy tool for
fast prototyping, aimed at students without a background in electronics and
programming. As soon as it reached a wider community, the Arduino board started
changing to adapt to new needs and challenges, differentiating its offer from simple
8-bit boards to products for IoT applications, wearable, 3D printing, and embedded
environments. All Arduino boards are completely open-source, empowering users to
build them independently and eventually adapt them to their particular needs. The
software, too, is open-source, and it is growing through the contributions of users
worldwide.
WHY ARDUINO?
Thanks to its simple and accessible user experience, Arduino has been used
in thousands of different projects and applications. The Arduino software is easy-
touse for beginners, yet flexible enough for advanced users. It runs on Mac, Windows,
and Linux. Teachers and students use it to build low cost scientific instruments, to
10
prove chemistry and physics principles, or to get started with programming and
robotics. Designers and architects build interactive prototypes, musicians and artists
use it for installations and to experiment with new musical instruments. Makers, of
course, use it to build many of the projects exhibited at the Maker Faire, for example.
Arduino is a key tool to learn new things. Anyone - children, hobbyists, artists,
programmers - can start tinkering just following the step by step instructions of a kit,
or sharing ideas online with other members of the Arduino community.
There are many other microcontrollers and microcontroller platforms available

for physical computing. Parallax Basic Stamp, Netmedia's BX-24, Phidgets, MIT's
Handyboard, and many others offer similar functionality. All of these tools take the
messy details of microcontroller programming and wrap it up in an easy-to-use
package. Arduino also simplifies the process of working with microcontrollers, but it
offers some advantage for teachers, students, and interested amateurs over other
systems:
 Inexpensive - Arduino boards are relatively inexpensive compared to

other microcontroller platforms. The least expensive version of the Arduino
module can be assembled by hand, and even the pre-assembled Arduino
modules cost less than $50.
 Cross-platform - The Arduino Software (IDE) runs on Windows,

Macintosh OSX, and Linux operating systems. Most microcontroller systems
are limited to Windows.
 Simple, clear programming environment - The Arduino Software

(IDE) is easy-to-use for beginners, yet flexible enough for advanced users to
take advantage of as well. For teachers, it's conveniently based on the
Processing programming environment, so students learning to program in that
environment will be familiar with how the Arduino IDE works.
 Open source and extensible software - The Arduino software is

published as open source tools, available for extension by experienced
programmers. The language can be expanded through C++ libraries, and
people wanting to understand the technical details can make the leap from
11
Arduino to the AVR C programming language on which it's based. Similarly,
you can add AVR-C code directly into your Arduino programs if you want to.
 Open source and extensible hardware - The plans of the Arduino

boards are published under a Creative Commons license, so experienced
circuit designers can make their own version of the module, extending it and
improving it. Even relatively inexperienced users can build the breadboard
version of the module in order to understand how it works and save money.
4.1.1.1 ARDUINO MEGA
The MEGA 2560 is designed for more complex projects. With 54 digital I/O
pins, 16 analog inputs and a larger space for your sketch it is the recommended board
for 3D printers and robotics projects. This gives your projects plenty of room and
opportunities.
Fig: 4.1 Arduino mega board
The Arduino Mega 2560 is a microcontroller board based on the

ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM
outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal
oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It
contains everything needed to support the microcontroller; simply connect it to a
computer with a USB cable or power it with an AC-to DC adapter or battery to get
started. The Mega 2560 board is compatible with most shields designed for the Uno
and the former boards Duemilanove or Diecimila.
12
TABLE 4.1 :TECHNICAL SPECIFICATIONS:
Microcontroller ATmega2560
Operating Voltage 5V
Input Voltage (recommended) 7-12V
Input Voltage (limit) 6-20V
Digital I/O Pins 54 (of which 15 provide PWM output)
Analog Input Pins 16
DC Current per I/O Pin 20 mA
DC Current for 3.3V Pin 50 mA
Flash Memory 256 KB of which 8 KB used by boot loader
SRAM 8 KB
EEPROM 4 KB
Clock Speed 16 MHz
LED_BUILTIN 13
Length 101.52 mm
Width 53.3 mm
Weight 37 g
Fig 4.2: Arduino mega
Arduino is open-source hardware. The hardware reference designs are

distributed under a Creative Commons Attribution Share-Alike 2.5 license and are
available on the Arduino website. Layout and production files for some versions of the
hardware are also available.
13
Although the hardware and software designs are freely available under copyleft
licenses, the developers have requested the name Arduinoto be exclusive to the
official product and not be used for derived works without permission. The official
policy document on use of the Arduino name emphasizes that the project is open to
incorporating work by others into the official product. Several Arduino-compatible
products commercially released have avoided the project name by using various
names ending in -duino. An early Arduino board with an RS-232 serial interface (upper
left) and an Atmel ATmega8 microcontroller chip (black, lower right); the 14 digital I/O
pins are at the top, the 6 analog input pins at the lower right, and the power connector
at the lower left.
Most Arduino boards consist of an Atmel 8-bit AVR microcontroller (ATmega8,

ATmega168, ATmega328, ATmega1280, ATmega2560) with varying amounts of
flash memory, pins, and features. The 32-bit Arduino Due, based on the Atmel
SAM3X8E was introduced in 2012. The boards use single or double-row pins or
female headers that facilitate connections for programming and incorporation into
other circuits. These may connect with add-on modules termed shields. Multiple and
possibly stacked shields may be individually addressable via an I²C serial bus. Most
boards include a 5 V linear regulator and a 16 MHz crystal oscillator or ceramic
resonator. Some designs, such as the LilyPad, run at 8 MHz and dispense with the
onboard voltage regulator due to specific formfactor restrictions.
Arduino microcontrollers are pre-programmed with a boot loader that simplifies

uploading of programs to the on-chip flash memory. The default bootloader of the
Arduino UNO is the optiboot bootloader. Boards are loaded with program code via a
serial connection to another computer. Some serial Arduino boards contain a level
shifter circuit to convert between RS-232 logic levels and transistor– transistor logic
(TTL) level signals. Current Arduino boards are programmed via Universal Serial Bus
(USB), implemented using USB-to-serial adapter chips such as the FTDI FT232.
Some boards, such as later-model Uno boards, substitute the FTDI chip with a
separate AVR chip containing USB-to-serial firmware, which is reprogrammable via
its own ICSP header. Other variants, such as the Arduino Mini and the unofficial
Boarduino, use a detachable USB-to-serial adapter board or cable, Bluetooth or other
methods. When used with traditional microcontroller tools, instead of the Arduino IDE,
14
standard AVR in-system programming (ISP) programming is used.An official Arduino
Uno R2 with descriptions of the I/O locations
The Arduino board exposes most of the microcontroller's I/O pins for use by
other circuits. The Diecimila, Duemilanove, and current Uno provide 14 digital I/O pins,
six of which can produce pulse-width modulated signals, and six analog inputs, which
can also be used as six digital I/O pins. These pins are on the top of the board, via
female 0.1-inch (2.54 mm) headers. Several plug-in application shields are also
commercially available. The Arduino Nano, and Arduino-compatible Bare Bones
Board and Boarduino boards may provide male header pins on the underside of the
board that can plug into solderless breadboards.
Many Arduino-compatible and Arduino-derived boards exist. Some are

functionally equivalent to an Arduino and can be used interchangeably. Many
enhance the basic Arduino by adding output drivers, often for use in school-level
education, to simplify making buggies and small robots. Others are electrically
equivalent but change the form factor, sometimes retaining compatibility with shields,
sometimes not. Some variants use different processors, of varying compatibility.
The Mega 2560 board can be programmed with the Arduino Software (IDE).
For details, see the reference and tutorials.
The ATmega2560 on the Mega 2560 comes preprogrammed with a boot loader
that allows you to upload new code to it without the use of an external hardware
programmer. It communicates using the original STK500 protocol (reference, C
header files).
You can also bypass the boot loader and program the microcontroller through
the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see
these instructions for details.
15
Fig 4.3 Ultrasonic sensor code
The ATmega16U2 (or 8U2 in the rev1 and rev2 boards) firmware source code is
available in the Arduino repository. The ATmega16U2/8U2 is loaded with a DFU boot
loader, which can be activated by:
 On Rev1 boards: connecting the solder jumper on the back of the board
(near the map of Italy) and then resetting the 8U2.
 On Rev2 or later boards: there is a resistor that pulling the 8U2/16U2

HWB line to ground, making it easier to put into DFU mode. You can then
use Atmel's FLIP software (Windows) or the DFU programmer (Mac OS X
and Linux) to load a new firmware. Or you can use the ISP header with an
external programmer (overwriting the DFU boot loader). See this user-
contributed tutorial for more information.
 POWER: The Mega 2560 can be powered via the USB connection or with an
external power supply. The power source is selected automatically.
External (non-USB) power can come either from an AC-to-DC adapter (wallwart) or
battery. The adapter can be connected by plugging a 2.1mm centerpositive plug into
the board's power jack. Leads from a battery can be inserted in the GND and Vin pin
headers of the POWER connector.
The board can operate on an external supply of 6 to 20 volts. If supplied with

less than 7V, however, the 5V pin may supply less than five volts and the board may
16
become unstable. If using more than 12V, the voltage regulator may overheat and
damage the board. The recommended range is 7 to 12 volts.
The power pins are as follows:
 Vin. The input voltage to the board when it's using an external power
source (as opposed to 5 volts from the USB connection or other
regulated power source). You can supply voltage through this pin, or,
if supplying voltage via the power jack, access it through this pin.
 5V. This pin outputs a regulated 5V from the regulator on the board.
The board can be supplied with power either from the DC power jack
(7 - 12V), the USB connector (5V), or the VIN pin of the board (712V).
Supplying voltage via the 5V or 3.3V pins bypasses the regulator, and
can damage your board. We don't advise it.
 3V3. A 3.3 volt supply generated by the on-board

regulator.Maximum current draw is 50 mA.
 GND. Ground pins.
 IOREF. This pin on the board provides the voltage reference with
which the microcontroller operates. A properly configured shield can
read the IOREF pin voltage and select the appropriate power source
or enable voltage translators on the outputs for working with the 5V or
3.3V.
 MEMORY: The ATmega2560 has 256 KB of flash memory for storing code (of
which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM
(which can be read and written with the EEPROM library).
 INPUT AND OUTPUT: ATmega2560-Arduino Pin Mapping.
17
Fig 4.4: Arduino Mega 2560 PIN diagram
Above is the pin mapping for the Atmega2560. The chip used in Arduino 2560. There
are pin mappings to Atmega8 and Atmega 168/328 as well.
TABLE 4.2 Arduino Mega 2560 PIN mapping table
Pin Number Pin Name Mapped Pin Name

1 PG5 ( OC0B ) Digital pin 4 (PWM)
2 PE0 ( RXD0/PCINT8 ) Digital pin 0 (RX0)
3 PE1 ( TXD0 ) Digital pin 1 (TX0)

4 PE2 ( XCK0/AIN0 )
5 PE3 ( OC3A/AIN1 ) Digital pin 5 (PWM)

6 PE4 ( OC3B/INT4 ) Digital pin 2 (PWM)
7 PE5 ( OC3C/INT5 ) Digital pin 3 (PWM)
8 PE6 ( T3/INT6 )
9 PE7 ( CLKO/ICP3/INT7 )
10 VCC VCC
11 GND GND
12 PH0 ( RXD2 ) Digital pin 17 (RX2)
13 PH1 ( TXD2 ) Digital pin 16 (TX2)
18
14 PH2 ( XCK2 )
15 PH3 ( OC4A ) Digital pin 6 (PWM)

16 PH4 ( OC4B ) Digital pin 7 (PWM)
17 PH5 ( OC4C ) Digital pin 8 (PWM)
18 PH6 ( OC2B ) Digital pin 9 (PWM)
19 PB0 ( SS/PCINT0 ) Digital pin 53 (SS)
20 PB1 ( SCK/PCINT1 ) Digital pin 52 (SCK)
21 PB2 ( MOSI/PCINT2 ) Digital pin 51 (MOSI)
22 PB3 ( MISO/PCINT3 ) Digital pin 50 (MISO)
23 PB4 ( OC2A/PCINT4 ) Digital pin 10 (PWM)
24 PB5 ( OC1A/PCINT5 ) Digital pin 11 (PWM)
25 PB6 ( OC1B/PCINT6 ) Digital pin 12 (PWM)
26 PB7 ( OC0A/OC1C/PCINT7 ) Digital pin 13 (PWM)
27 PH7 ( T4 )
28 PG3 ( TOSC2 )
29 PG4 ( TOSC1 )
30 RESET RESET
31 VCC VCC
32 GND GND
33 XTAL2 XTAL2
34 XTAL1 XTAL1
35 PL0 ( ICP4 ) Digital pin 49
36 PL1 ( ICP5 ) Digital pin 48

37 PL2 ( T5 ) Digital pin 47
38 PL3 ( OC5A ) Digital pin 46 (PWM)
39 PL4 ( OC5B ) Digital pin 45 (PWM)
40 PL5 ( OC5C ) Digital pin 44 (PWM)
41 PL6 Digital pin 43
42 PL7 Digital pin 42
43 PD0 ( SCL/INT0 ) Digital pin 21 (SCL)
19
44 PD1 ( SDA/INT1 ) Digital pin 20 (SDA)
45 PD2 ( RXDI/INT2 ) Digital pin 19 (RX1)
46 PD3 ( TXD1/INT3 ) Digital pin 18 (TX1)
47 PD4 ( ICP1 )
48 PD5 ( XCK1 )
49 PD6 ( T1 )
50 PD7 ( T0 ) Digital pin 38

51 PG0 ( WR ) Digital pin 41
52 PG1 ( RD ) Digital pin 40
53 PC0 ( A8 ) Digital pin 37
61 VCC VCC
62 GND GND
63 PJ0 ( RXD3/PCINT9 ) Digital pin 15 (RX3)
64 PJ1 ( TXD3/PCINT10 ) Digital pin 14 (TX3)
65 PJ2 ( XCK3/PCINT11 )
66 PJ3 ( PCINT12 )
67 PJ4 ( PCINT13 )
68 PJ5 ( PCINT14 )
69 PJ6 ( PCINT 15 )
70 PG2 ( ALE ) Digital pin 39

71 PA7 ( AD7 ) Digital pin 29
20
79 PJ7
80 VCC VCC
81 GND GND
82 PK7 ( ADC15/PCINT23 ) Analog pin 15
90 PF7 ( ADC7 ) Analog pin 7
92 PF5 ( ADC5/TMS ) Analog pin 5
93 PF4 ( ADC4/TMK ) Analog pin 4
98 AREF Analog Reference
99 GND GND
100 AVCC VCC
Each of the 54 digital pins on the Mega can be used as an input or output,
using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts.
Each pin can provide or receive 20 mA as recommended operating condition and has
21
an internal pull-up resistor (disconnected by default) of 20-50 k ohm. A maximum of
40mA is the value that must not be exceeded to avoid permanent damage to the
microcontroller.
In addition, some pins have specialized functions:
 Serial: 0 (RX) and 1 (TX); Serial 1: 19 (RX) and 18 (TX); Serial 2: 17 (RX)
and 16 (TX); Serial 3: 15 (RX) and 14 (TX). Used to receive (RX) and
transmit (TX) TTL serial data. Pins 0 and 1 are also connected to the
corresponding pins of the ATmega16U2 USB-to-TTL Serial chip.
 External Interrupts: 2 (interrupt 0), 3 (interrupt 1), 18 (interrupt 5), 19

(interrupt 4), 20 (interrupt 3), and 21 (interrupt 2). These pins can be
configured to trigger an interrupt on a low level, a rising or falling edge, or
a change in level. See the attachInterrupt() function for details.
 PWM: 2 to 13 and 44 to 46. Provide 8-bit PWM output with the

analogWrite() function.
 SPI: 50 (MISO), 51 (MOSI), 52 (SCK), 53 (SS). These pins support SPI

communication using theSPI library. The SPI pins are also broken out on
the ICSP header, which is physically compatible with the Arduino /Genuino
Uno and the old Duemilanove and Diecimila Arduino boards.
 LED: 13. There is a built-in LED connected to digital pin 13. When the pin
is HIGH value, the LED is on, when the pin is LOW, it's off.
 TWI: 20 (SDA) and 21 (SCL). Support TWI communication using the Wire
library. Note that these pins are not in the same location as the TWI pins
on the old Duemilanove or Diecimila Arduino boards.
See also the mapping Arduino Mega 2560 PIN diagram.
The Mega 2560 has 16 analog inputs, each of which provide 10 bits of resolution (i.e.
1024 different values). By default they measure from ground to 5 volts, though is it
possible to change the upper end of their range using the AREF pin and analog
Reference() function.
22
There are a couple of other pins on the board:
 AREF. Reference voltage for the analog inputs.

Used with analogReference().
 Reset. Bring this line LOW to reset the microcontroller. Typically used to
add a reset button to shields which block the one on the board.
 COMMUNICATION: The Mega 2560 board has a number of facilities for

communicating with a computer, another board, or other microcontrollers. The
ATmega2560 provides four hardware UARTs for TTL (5V) serial communication.
An ATmega16U2 (ATmega 8U2 on the revision 1 and revision 2 boards) on the
board channels one of these over USB and provides a virtual com port to software
on the computer (Windows machines will need a .inf file, but OSX and Linux
machines will recognize the board as a COM port automatically. The Arduino
Software (IDE) includes a serial monitor which allows simple textual data to be
sent to and from the board. The RX and TX LEDs on the board will flash when
data is being transmitted via the
ATmega8U2/ATmega16U2 chip and USB connection to the computer (but not for
serial communication on pins 0 and 1.
A SoftwareSerial library allows for serial communication on any of the Mega

2560's digital pins.
The Mega 2560 also supports TWI and SPI communication. The Arduino
Software (IDE) includes a Wire library to simplify use of the TWI bus; see the
documentation for details. For SPI communication, use the SPI library.
 AUTOMATIC (SOFTWARE) RESET: Rather than requiring a physical press of the

reset button before an upload, the Mega 2560 is designed in a way that allows it
to be reset by software running on a connected computer. One of the hardware
flow control lines (DTR) of the ATmega8U2 is connected to the reset line of the
ATmega2560 via a 100 nanofarad capacitor. When this line is asserted
(taken low), the reset line drops long enough to reset the chip. The Arduino Software
(IDE) uses this capability to allow you to upload code by simply pressing the upload
23
button in the Arduino environment. This means that the bootloader can have a shorter
timeout, as the lowering of DTR can be wellcoordinated with the start of the upload.
This setup has other implications. When the Mega 2560 board is connected to
either a computer running Mac OS X or Linux, it resets each time a connection is
made to it from software (via USB). For the following half-second or so, the bootloader
is running on the ATMega2560. While it is programmed to ignore malformed data (i.e.
anything besides an upload of new code), it will intercept the first few bytes of data
sent to the board after a connection is opened. If a sketch running on the board
receives one-time configuration or other data when it first starts, make sure that the
software with which it communicates waits a second after opening the connection and
before sending this data.
The Mega 2560 board contains a trace that can be cut to disable the auto-
reset. The pads on either side of the trace can be soldered together to re-enable it.
It's labeled "RESET-EN". You may also be able to disable the auto-reset by
connecting a 110 ohm resistor from 5V to the reset line; see this forum thread for
details.
 REVISIONS: The Mega 2560 does not use the FTDI USB-to-serial driver chip
used in past designs. Instead, it features the ATmega16U2 (ATmega8U2 in the
revision 1 and revision 2 Arduino boards) programmed as a USB-to-serial
converter. Revision 2 of the Mega 2560 board has a resistor pulling the 8U2 HWB
line to ground, making it easier to put into DFU mode.
Revision 3 of the Arduino board and the current Genuino Mega 2560 have the
following improved features:
 1.0 pinout: SDA and SCL pins - near to the AREF pin - and two other
new pins placed near to the RESET pin, the IOREF that allow the shields
to adapt to the voltage provided from the board. In future, shields will be
compatible both with the board that use the AVR, which operate with 5V
and with the board that uses ATSAM3X8E, that operate with 3.3V. The
second one is a not connected pin that is reserved for future purposes.
 Stronger RESET circuit.
24
 Atmega 16U2 replace the 8U2.
APPLICATIONS:
 Arduboy, a handheld game console based on Arduino.

 Arduinome, a MIDI controller device that mimics the Monome.
 Ardupilot, drone software and hardware.
 ArduSat, a cubesat based on Arduino.
 C-STEM Studio, a platform for hands-on integrated learning of computing,

science, technology, engineering, and mathematics (C-STEM) with
robotics.
 Data loggers for scientific research.
 OBDuino, a trip computer that uses the on-board diagnostics interface
found in most modern cars.
4.1.2 POWER SUPPLY
This section describes how to generate +5V DC power supply
Fig 4.5: Power supply diagram
The power supply section is the important one. It should deliver constant output
regulated power supply for successful working of the project. A 0-12V/1 mA
transformer is used for this purpose. The primary of this transformer is connected in
to main supply through on/off switch& fuse for protecting from overload and short
circuit protection. The secondary is connected to the diodes to convert 12V AC to 12V
25
DC voltage. And filtered by the capacitors, which is further regulated to +5v, by using
IC 7805.
4.1.2 GSM
A GSM modem is a wireless modem that works with a GSM wireless
Fig 4.6: GSM module
network. A wireless modem behaves like a dial-up modem. The main

difference between them is that a dial-up modem sends and receives data through a
fixed telephone line while a wireless modem sends and receives data through radio
waves. The working of GSM modem is based on commands, the commands always
start with AT (which means ATtention) and finish with a <CR> character. For example,
the dialing command is ATD<number>; ATD3314629080; here the dialing command
ends with semicolon.
The AT commands are given to the GSM modem with the help of PC or
controller. The GSM modem is serially interfaced with the controller with the help of
MAX 232. Here max 232 acts as driver which converts TTL levels to the RS 232 levels.
For serial interface GSM modem requires the signal based on RS 232 levels. The
T1_OUT and R1_IN pin of MAX 232 is connected to the TX and RX pin of GSM
modem
 OBJECT OF THE DOCUMENT: This document gives an overview of the

LinkSprite GSM/GPRS module: a miniature, single-side board, quad-band GSM
26
850/EGSM 900/DCS 1800/PCS 1900 module, ready for integration in various
kinds of Fix wireless phones and other wireless devices.
Fig 4.7: System block diagram
TABLE 4.3: PRODUCT DESCRIPTION
4.1.2.1 FUNCTIONAL DESCRIPTION
 RF Functionalities: The RF part of this module converts RF signals to baseband

for receiver chain and translates base band signals into RF frequency spectrum.
27
The operating frequencies are:
Rx (EGSM 850): 869 to 894MHz
Tx (EGSM 850): 824 to 849MHz
Rx (EGSM 900): 925 to 960MHz
Tx (EGSM 900): 880 to 915MHz
Rx (DCS 1800): 1805 to 1880MHz
Tx (DCS 1800): 1710 to 1785MHz
Rx (PCS 1900): 1930 to 1990MHz
Tx (PCS 1900): 1850 to 1910MHz
 Baseband Functionalities: The baseband part of SM5210 is composed of a

SPREADTRUM’s SC6600D chip. This chipset is using 0.18µm mixed signal
CMOS technology which allows massive integration as well as low power
consumption. SC6600D provides single-chip solution to wireless Quad-band
telephone handsets and data modems confirming to the EGSM 900, GSM 850,
DCS 1800 and PCS 1900.
 Memory Functionalities :The memory used in this module is a combination of 32

Megabit (2M x 16-Bit) CMOS 3.0V Volt-only, simultaneous operation flash memory
and 4 Megabit (256K x 16-Bit) static RAM.
4.1.3 POWER SUPPLY
Power Supply Description
28
The power supply is one of the key issues in the designing GSM terminals.
Due to the 577us radio burst emission in GSM every 4.615ms, power supply must
be able to deliver high current peaks in a short time. During these peaks, ripples
and drops on the supply voltage must not exceed a certain limit.
Table 4.4: VBAT Pin Description
Pin number VMIN VNOM VMAX Ripple max
VBAT (V) 1,3,5,7 3.3V (*) 3.6V 4.2V (**)

50mVPP for
freq<200KHZ
2mVPP for
freq>200KHZ
(*): This value has to be guaranteed during the burst (with 2.0A Peak in GSM or GPRS
mode).
(**): max operation Voltage Stationary Wave Ratio.
When supplying the module with a battery, the total impedance (battery + protections
+ PCBS) should be less than 150mOhms.
Table : 4.5 GND Pin Description
Pin number Description

GND 9,11,13,15,17
Shielding can Ground
install pin(*)
Table 4.6: Power consumption in OFF mode
29
Table 4.7 : Power consumption in EGSM 900MHZ
(*): PCL: Power control level

PCL0: 1W emission requested (max power)
PCL3: 0.25W emission requested
Table 4.8 : Power consumption in DCS/PCS 1800MHZ
 VCC OUTPUT : This output can be used to power some external functions, such
as LCD.
Table 4.9 : VCC Pin Description
30
Table 4.8 : VCC Electrical Characteristics
 SPI INTERFACE : The SPI bus includes a CLK signal, an IO signal, a RS signal
and a CS signal complying with the standard SPI bus. These pins can also be
used as GPIO.
Table 4.10 : SPI Pin Description
 KEYPAD INTERFACE : This interface provides 10 connections: 4 rows (KBR0 to

KBR3) and 6 columns (KBC0 to KBC5).
31
No external pull-up resistors are needed when the internal pull-up at the input pads
are enabled.
Fig 4.8: Keypad connection SIM
 General Description: The SIM interface is compatible with the ISO 7816-3 IC
card standard required by the GSM 11.11 Phase 2+ standard. The module also
supports Release 99 of the SIM Toolkit recommendation and supports a Fixed
Dialling Number directory.
TABLE 4.11: SIM Interface
Pin number Type Description

29 I/O SIM Serial Data
27 O SIM Clock
21 O SIM Reset
51 P SIM Power Supply

Parameter Max Remarks
VL (V) 0.6/0.8
VH (V) -
32
Fig 4.9: SIM connection (no power control)
Figure 3 shows system design for 3.0V and 1.8V SIM card interface. The SIM
level shift is built in the SC6600D chip.
Note:
1) SIM_VCC need add three capacitor: 4.7uF, 0.1uF, 27pF.
2) SIM_RST, SIM_DATA, SIM_CLK lines also need add 27pF capacitor for each
line.
3) SIM_DATA need to Pull-up with 2K resistor to SIM_VCC.
NOTES: Does not support 5V SIM card.
AUDIO
The module supports the following voice codec:

• Full-Rate
• Enhanced Full Rate
Two different microphone inputs and two different speaker outputs are supported.
Table 4.12 : Audio Interface
Pin number Pin name Type Description
18 EAR_SPKP AO Earphone Differential Positive Output
33
16 EAR_SPKN AO Earphone Differential Negative Output
14 EAR_MICP AI Microphone Differential Positive Input
12 EAR_MICN AI Microphone Differential Negative Input
44 AUX_SPKP AO Auxiliary Speaker Differential Positive Output
58 AUX_SPKN AO Auxiliary Speaker Differential Negative Output
42 AUX_MICP AI Auxiliary Microphone Differential Positive Input
50 AUX_MICN AI Auxiliary Microphone Differential Negative Input
Their frequency response curve should be within the mask given by GSM
specification.
Figure 4.9: Audio Frequency Response Curve
Typical Microphone Inputs Characteristics
The gain of MIC inputs is internally adjusted and can be turned from 9dB to 42dB.
Table 4.13: Microphone Electrical Characteristics
Conditions/Comment
Parameter s Min. Typ. Units
Input common mode range EAR_SPKP 0.6 V
PGA gain range 9 dB
Maximum analog input range after PGA Differential V
Digital audio output sample rate 8 kHz
ADC resolution 13 bits
ADC signal to (noise + distortion) ratio dB
Digital output word 16 bits
34
 Typical Speaker Outputs Characteristics: The gain of speaker outputs is
internally adjusted and can be turned from -21dB to 12dB.
Table 4.14 : Speaker Electrical Characteristics
Parameter Conditions/Comments Min. Typ. Max. Units
Maximum differential output voltage ±1.4 V
Maximum single-ended output voltage 1.4 V
Output common mode voltage 1.1 V
Minimum load resistance 16 Ω

gain range -21 12 dB
 Typical Microphone Connection: Two MIC inputs already include the biasing for
an electret microphone allowing easy connection to the headset.
The connection can be either differential or single ended; but using a

differential connection in order to reject common mode noise TDMA noise is
strongly recommended.
 Recommended characteristics for the microphone Type: Electret
 Impedance: 2.2Kohm
 Sensitivity: -42dB(typ)
 SNR > 50dB min
 Frequency response compatible with the GSM specifications
 Differential Connection: The recommended characteristic of capacitors:

C1=22pF to 47pF
C2=C3=C4=47pF to 100pF
L1=L2=100nH
35
Fig 4.10: MIC input (differential input)
Microphone manufacturer can provide a microphone soldered C1 directly on it, so

that C1 can be the nearest to the Microphone.
Single-ended Connection
Fig 4.11: MIC input (single-ended input)
Do not recommend this connection.
When using a single-ended connection, be sure to have a very good ground plane,
a very good filtering as well as shielding in order to avoid any disturbance on the
audio path.
The recommended characteristic:
C1=22pF to 47pF
C2= C3=47pF to 100p
L1= 100nH
Microphone manufacturer can provide a microphone soldered C1 directly on it, so

that C1 can be the nearest to the Microphone.
36
 Typical Speaker Connection :
Recommended characteristics for the speaker

Type: 10 to 100mW, electro-magnetic
Impedance: 16 to 150 Ohm
Sensitivity: 110dB SPL min. (0dB = 120uPa)
Frequency response compatible with the GSM specifications.
4.1.4 RFID READER AND TAG
An RFID reader is a device that is used to interrogate an RFID tag. The reader
has an antenna that emits radio waves; the tag responds by sending back its data.
An RFID tag is a microchip combined with an antenna in a compact package;

the packaging is structured to allow the RFID tag to be attached to an object to be
tracked. "RFID" stands for Radio Frequency Identification. The tag's antenna picks
up signals from an RFID reader or scanner and then returns the signal, usually with
some additional data (like a unique serial number or other customized information).
A passive tag is an RFID tag that does not contain a battery; the power is
supplied by the reader. When radio waves from the reader are encountered by a
passive rfid tag, the coiled antenna within the tag forms a magnetic field. The tag
draws power from it, energizing the circuits in the tag. The tag then sends the
information encoded in the tag's memory.
The RX and TX pins of RFID reader connected to Tx and Rx pins of 8051

Microcontroller respectively. Then the reader senses the data from the Tag and
transmits the sensed data to microcontroller via serial port.
37
Fig 4.12: RFID reader Fig4.13: RFID card
The EM-18 RFID Reader module operating at 125kHz is an inexpensive solution

for your RFID based application. The Reader module comes with an on-chip antenna
and can be powered up with a 5V power supply. Power-up the module and connect
the transmit pin of the module to recieve pin of your microcontroller. Show your card
within the reading distance and the card number is thrown at the output. Optionally
the module can be configured for also a weigand output.
Typical application
E-Payment
• E-Toll Road Pricing
• E-Ticketing for Events
• E-Ticketing for Public Transport
• Access Control
• PC Access
• Authentication
• Printer / Production Equipment
38
Fig 4.14: Application circuit
4.1.5 KEYPAD
At the lowest level, keyboards are organized in a matrix of rows and columns. The
CPU accesses both rows and column through ports; therefore, with two 8-bit ports,
an 8*8 matrix of keys can be connected to a microprocessor. When a key pressed,
a row and column make a connect otherwise, there is no connection between row
and column. In IBM PC keyboards, a single microcontroller (consisting of
microprocessor, RAM and EPROM, and several ports all on a single chip) takes care
of software and hardware interfacing of keyboard. In such systems it is the function
of programs
39
Fig 4.15: Keypad
stored in the EPROM of microcontroller to scan the keys continuously, identify which
one has been activated, and present it to the motherboard.
Figure shows a 4*4 matrix connected to two ports. The rows are connected to
an output port and the columns are connected to an input port. If no key has been
pressed, reading the input port will yield 1s for all columns since they are all
connected to high (Vcc) If all the rows are grounded and a key is pressed, one of the
columns will have 0 since the key pressed provides the path to ground. It is the
function of the microcontroller to scan the keyboard continuously to detect and
identify the key pressed.
Grounding rows and reading columns
To detect a pressed key, the microcontroller grounds all rows by providing 0 to the
output latch, and then it reads the columns. If the data read from the columns is
D3D0=1111, no key has been pressed and the process continues until a key press is
detected. However, if one of the column bits has a zero, this means that a key press
has occurred. For example, if D3-D0=1101, this means that a key in the D1 column
has been pressed. After a key press is detected, the microcontroller will go through
the process of identifying the key. Starting with the top row, the microcontroller
grounds it by providing a low to row D0 only; then it reads the columns. If the data
40
read is all1s, no key in that row is activated and the process is moved to the next row.
It grounds the next row, reads the columns, and checks for any zero. This process
continues until the row is identified. After identification of the row in which the key has
been pressed, the next task is to find out which column the pressed key belongs to.
This should be easy since the microcontroller knows at any time which row and
column are being accessed.
In the program, it is assumed that P1 and P2 are initialized as output and input,
respectively. Program13.1 goes through the following four major stages:
1. To make sure that the preceding key has been released, 0s are output to all
rows at once, and the columns are read and checked repeatedly until all the
columns are high. When all columns are found to be high, the program waits for a
short amount of time before it goes to the next stage of waiting for a key to be
pressed.
2. To see if any key is pressed, the columns are scanned over and over in an
infinite loop until one of them has a 0 on it. Remember that the output latches
connected to rows still have their initial zeros (provided in stage 1), making them
grounded. After the key press detection, it waits 20ms for the bounce and then
scans the columns again. This serves two functions: (a) it ensures that the first key
press detection was not an erroneous one due to spike noise, and(b) the 20ms
delay prevents the same key press from being interpreted as a multiple key press.
If after the 20-ms delay the key is still pressed, it goes to the next stage to detect
which row it belongs to; otherwise, it goes back into the loop to detect a real key
press.
3. To detect which row the key press belongs to, it grounds one row at a time,
reading the columns each time. If it finds that all columns are high, this means that
the key press cannot belong to that row; therefore, it grounds the next row and
continues until it finds the row the key press belongs to. Upon finding the row that
the key press belongs to, it sets up the starting address for the look-up table holding
the scan codes (or the ASCII value) for that row and goes to the next stage to
identify the key.
4. To identify the key press, it rotates the column bits, one bit at a time, into the
carry flag and checks to see if it is low. Upon finding the zero, it pulls out the ASCII
41
code for that key from the look-up table; Otherwise, it increments the pointer to point
to the next element of the look-up table.
While the key press detection is standard for all keyboards, the process for
determining which key is pressed varies. The look-up table method shown in program
can be modified to work with any matrix up to 8*8.
4.1.6 LCD
LCD screen is an electronic display module and find a wide range of

applications. A 16x2 LCD display is very basic module and is very commonly used in
various devices and circuits. These modules are preferred over seven segments and
other multi segment LEDs. The reasons being: LCDs are economical; easily
programmable; have no limitation of displaying special & even custom characters
(unlike in seven segments), animations and so on.
A 16x2 LCD means it can display 16 characters per line and there are 2 such
lines. In this LCD each character is displayed in 5x7 pixel matrix. This LCD has two
registers, namely, Command and Data. The command register stores the command
instructions given to the LCD. A command is an instruction given to LCD to do a
predefined task like initializing it, clearing its screen, setting the cursor position,
controlling display etc. The data register stores the data to be displayed on the LCD.
The data is the ASCII value of the character to be displayed on the LCD. Click to
learn more about internal structure of a LCD.
Fig 4.16: LCD
It come across LCD displays everywhere around them. Computers,

calculators, television sets, mobile phones, digital watches use some kind of display
to display the time. An LCD is an electronic display module which uses liquid crystal
to produce a visible image. The 16×2 LCD display is a very basic module commonly
42
used in projects. The 16×2 translates to a display 16 characters per line in 2 such
lines. In this LCD each character is displayed in a 5×7 pixel matrix.
Table 4.15: Pin detail of LCD display
PIN FUNCTION NAME

NO.
1 Ground (0V) Ground
2 Supply voltage; 5V (4.7V – 5.3V) VCC
3 Contrast adjustment; the best way is to use a variable resistor such Vo / VEE
as a potentiometer. The output of the potentiometer is connected
to this pin. Rotate the potentiometer knob forward and backwards
to adjust the LCD contrast.
4 Selects command register when low, and data register when high RS
(Register
Select )
5 Low to write to the register; High to read from the register Read/writ
e
6 Sends data to data pins when a high to low pulse is given; Extra Enable
voltage push is required to execute the instruction and EN(enable)
signal is used for this purpose. Usually, we make it en=0 and when
we want to execute the instruction we make it high en=1 for some
milliseconds. After this we again make it ground that is, en=0.
7 8-bit data pins DB0

8 DB1
9 DB2
43
10 DB3
11 DB4
12 DB5
13 DB6
14 DB7
15 Backlight VCC (5V) Led+
16 Backlight Ground (0V) Led-
 RS (REGISTER SELECT) : A 16X2 LCD has two registers, namely, command and
data. The register select is used to switch from one register to other. RS=0 for
command register, whereas RS=1 for data register.
 COMMAND REGISTER : The command register stores the command instructions

given to the LCD. A command is an instruction given to LCD to do a predefined
task like initializing it, clearing its screen, setting the cursor position, controlling
display etc. Processing for commands happens in the command register.
 DATA REGISTER : The data register stores the data to be displayed on the LCD.
The data is the ASCII value of the character to be displayed on the LCD. When we
send data to LCD it goes to the data register and is processed there. When RS=1,
data register is selected.
44
Fig 4.17: Data register
TABLE 4.16: IMPORTANT COMMAND CODES FOR LCD
SR.NO. HEX CODE COMMAND TO LCD INSTRUCTION

REGISTER
1 01 Clear display screen
2 02 Return home
3 04 Decrement cursor (shift cursor to left)
4 06 Increment cursor (shift cursor to right)
5 05 Shift display right
6 07 Shift display left
7 08 Display off, cursor off
8 0A Display off, cursor on
9 0C Display on, cursor off
10 0E Display on, cursor blinking
11 0F Display on, cursor blinking
12 10 Shift cursor position to left
13 14 Shift cursor position to right
14 18 Shift the entire display to the left
15 1C Shift the entire display to the right
16 80 Force cursor to beginning ( 1st line)
17 C0 Force cursor to beginning ( 2nd line)
18 38 2 lines and 5×7 matrix
 DISPLAYING CUSTOM CHARACTERS ON 16X2 LCD:
Generating custom characters on LCD is not very hard. It requires the

knowledge about custom generated random access memory (CG-RAM) of LCD and
the LCD chip controller. Most LCDs contain Hitachi HD4478 controller. CG-RAM is
the main component in making custom characters. It stores the custom characters
once declared in the code. CG-RAM size is 64 byte providing the option of creating
eight characters at a time. Each character is eight byte in size.
CG-RAM address starts from 0x40 (Hexadecimal) or 64 in decimal. We can

generate custom characters at these addresses. Once we generate our characters
at these addresses, now we can print them on the LCD at any time by just sending
45
simple commands to the LCD. Character addresses and printing commands are
below.
In the table above you can see starting addresses for each character with their
printing commands. The first character is generated at address 0x40 to 0x47 and is
printed on LCD by just sending simple command 0 to the LCD. The second character
is generated at address 0x48 to 0x55 and is printed by sending 1 to LCD.
4.1.7 FINGERPRINT SENSOR
R305 Fingerprint Module consists of optical fingerprint sensor, high-speed

DSP processor, high-performance fingerprint alignment algorithm, high-capacity
FLASH chips and other hardware and software composition, stable performance,
simple structure, with fingerprint entry, image processing, fingerprint matching,
search and template storage and other functions.
Fig 4.18: Finger print sensor
 Fingerprint Module R305
R305 is a finger print sensor module with TTL UART interface. The user can
store the finger print data in the module and can configure it in 1:1 or 1: N mode for
identifying the person. The FP module can directly interface with 3v Microcontroller.
A level converter (like MAX232) is required for interfacing with PC.
The R305 fingerprint module has two interface TTL UART and USB2.0,
USB2.0 interface can be connected to the computer; RS232 interface is a TTL level,
the default baud rate is 57600 , can be changed, refer to a communication protocol ;
can And microcontroller, such as ARM, DSP and other serial devices with a
46
connection, 3.3V 5V microcontroller can be connected directly. Needs to connect the
computer level conversion, level conversion note, embodiments such as a MAX232
circuit.
4.1.7.1 Operation Principle
Fingerprint processing includes two parts: fingerprint enrollment and fingerprint

matching (the matching can be 1:1 or 1:N). When enrolling, user needs to enter the
finger two times. The system will process the two time finger images, generate a
template of the finger based on processing results and store the template. When
matching, user enters the finger through optical sensor and system will generate a
template of the finger and compare it with templates of the finger library. For 1:1
matching, system will compare the live finger with specific template designated in the
Module; for 1:N matching, or searching, system will search the whole finger library for
the matching finger. In both circumstances, system will return the matching result,
success or failure.USB Cable Connections are 5V/D+/D-/GND (Optional)
4.1.7.2 Features
 Supply voltage: DC 4.2 ~ 6.0V.

 Supply current: Working current: 50mA (typical) Peak current: 80mA.
 Fingerprint image input time: <0.3 seconds.
 Window area: 14x18 mm.
 Matching method: Comparison method (1: 1).
 Search method (1: N).
 Characteristic file: 256 bytes.
 Template file: 512 bytes.
 Storage capacity: 1000 pieces.
 Security Level: Five (from low to high: 1, 2, 3, 4, and 5).
 Fake rate (FAR): <0.001%.
 Refusal rate (FRR): <1.0%.
 Search time: <1.0 seconds (1: 1000 hours, mean value).
 Host interface: UART \ USB1.1.
 Communication baud rate (UART): (9600xN) bps Where N = 1 ~ 12
(default N = 6, ie 57600bps).
47
 Working environment: Temperature: -20 ℃ - +40 ℃ Relative
humidity:
40% RH-85% RH (no condensation).
 Package Includes:-
 1 - Finger Print Sensor (R305) -TTL UART

 1 - 6 pin RMC Connector with wire
 HARDWARE INTERFACE
Exterior View
Fig 4.19 : Hardware interface
 Serial Communication : When the FP module communicates with user device,

definition of J1 is as follows:
Table 4.17: Serial communication pin details
Pin number Name Type Function Description
1 5v In Power input (DC 4.2V- 6V)
2 GND - Signal ground .connected to power ground
3 TXD Out Data output. TTL logical level
4 RXD In Data input. TTL logical level
48
5 Touch OUT Finger detection signal （ maximum output current:
50mA）
6 3.3V In Finger detection power (DC3.3V - 5V、about 5uA)
 Hardware connection : Via serial interface, the Module may communicate with
MCU of 3.3V or 5V power: TXD (pin 3 of P1) connects with RXD (receiving pin of
MCU), RXD (pin 4 of P1) connects with TXD (transferring pin of MCU). Should the
upper computer (PC) be in RS-232 mode, please add level converting circuit, like
MAX232, between the Module and PC.
Table 4.18 : USB Communication
Pin number Name Type Function description
7 5V In Power Input
8 D+ Out USB data output.
9 D- In USB data input.
10 GND - Signal ground.
 Serial Communication
The mode is semi duplex asychronism serial communication. And the default
baud rate is 57600bps. User may set the baud rate in 9600 ～ 115200bps 。
Transferring frame format is 10 bit: the low-level starting bit, 8-bit data with the LSB
first, and an ending bit. There is no check bit.
 Reset time
49
At power on, it takes about 200ms for initialization. During this period, the
Module can’t accept commands for upper computer. To address demands of different
customer, Module system provides abundant resources at user’s use.
 Buffer
There are an image buffer and two 512-byte-character-file buffer within the
RAM space of the module. Users can read & write any of the buffers by instructions.
Note: Contents of the above buffers will be lost at Power-off.
 Image buffer
Image Buffer serves for image storage and the image format is 256*288
pixels, form is BMP. When transferring through UART, to quicken speed, only the
upper 4 bits of the pixel is transferred (that is 16 grey degrees). And two adjacent
pixels of the same row will form a byte before the transferring. When uploaded to PC,
the 16-grey-degree image will be extended to 256-grey-degree format. That’s 8-bit
BMP format. When transferring through USB, the image is 8-bit pixel, that’s 256 grey
degrees.
 Character file buffer
Character file buffer, CharBuffer1, CharBuffer2, can be used to store both

character file and template file.
 Fingerprint Library
System sets aside a certain space within Flash for fingerprint template storage,
that’s fingerprint library. Contents of the library remain at power off. Capacity of the
library changes with the capacity of Flash, system will recognize the latter
automatically. Fingerprint template’s storage in Flash is in sequential order. Assume
the fingerprint capacity N, then the serial number of template in library is 0, 1, 2, 3 …
N. User can only access library by template number.
Note: Commands shall only be sent from upper computer to the Module, and the
Module acknowledges the commands.
50
Upon receipt of commands, Module will report the commands execution status
and results to upper computer through acknowledge packet. Acknowledge packet
has parameters and may also have following data packet. Upper computer can’t
ascertain Module’s package receiving status or command execution results unless
through acknowledge packet sent from Module. Acknowledge packet includes 1 byte
confirmation code and maybe also the returned parameter.
Confirmation code’s definition is:
00h: command execution complete;

01h: error when receiving data package;
02h: no finger on the sensor;
03h: fail to enroll the finger;
04h: fail to generate character file due to the over-disorderly fingerprint image;
05h: fail to generate character file due to the over-wet fingerprint image;
06h: ail to generate character file due to the over-disorderly fingerprint image;
07h: fail to generate character file due to lackness of character point or oversmallness
of fingerprint image 08h: finger doesn’t match;
09h: fail to find the matching finger;
0Ah: fail to combine the character files;
0Bh: addressing PageID is beyond the finger library;
0Ch: error when reading template from library or the template is invalid;
0Dh: error when uploading template;
0Eh: Module can’t receive the following data packages.
0Fh: error when uploading image;
10h: fail to delete the template;
11h: fail to clear finger library;
13h: wrong password!
15h: fail to generate the image for the lackness of valid primary image;
18h: error when writing flash;
19h: No definition error;
1Ah: invalid register number;
1Bh: incorrect configuration of register;
1Ch: wrong notepad page number;
51
1Dh: fail to operate the communication port; others: system reserved;
41h: No finger on sensor when add fingerprint on second time.
42h: fail to enroll the finger for second fingerprint add.
43h: fail to generate character file due to lackness of character point or oversmallness
of fingerprint image for second fingerprint add
44h: fail to generate character file due to the over-disorderly fingerprint image for
second fingerprint add; 45h: Duplicate fingerprint.
Applications:
 Secure logins via keyboard modules

 User identification at kiosks
 Biometric door locks
 Credit card security
 Weapon activation
 Theft protection
4.1.8 BUZZER
Fig :Active Passive Buzzer

Active Passive Buzzer Pinout
TABLE 4.19 :Buzzer Pin Configuration
Pin Number Pin Name Description
52
1 Positive Identified by (+) symbol or longer terminal lead. Can be
powered by 6V DC
2 Negative Identified by short terminal lead. Typically connected to

the ground of the circuit
4.1.8.1 Buzzer Features and Specifications
• Rated Voltage: 6V DC
• Operating Voltage: 4-8V DC
• Rated current: <30mA
• Sound Type: Continuous Beep
• Resonant Frequency: ~2300 Hz
• Small and neat sealed package
• Breadboard and Perf board friendly
 Equivalents for Passive Buzzer: Piezo Electric buzzer, Speaker, Active Passive
Buzzer with Module
How to use a Buzzer
A buzzer is a small yet efficient component to add sound features to our

project/system. It is very small and compact 2-pin structure hence can be easily used
on breadboard, Perf Board and even on PCBs which makes this a widely used
component in most electronic applications.
There are two types are buzzers that are commonly available. The one shown
here is a simple buzzer which when powered will make a Continuous Beeeeeeppp....
sound, the other type is called a readymade buzzer which will look bulkier than this
and will produce a Beep. Beep. Beep. Sound due to the internal oscillating circuit
present inside it. But, the one shown here is most widely used because it can be
customised with help of other circuits to fit easily in our application.
53
This buzzer can be used by simply powering it using a DC power supply
ranging from 4V to 9V. A simple 9V battery can also be used, but it is recommended
to use a regulated +5V or +6V DC supply. The buzzer is normally associated with a
switching circuit to turn ON or turn OFF the buzzer at required time and require
interval.
Applications of Buzzer
• Alarming Circuits, where the user has to be alarmed about something

• Communication equipments
• Automobile electronics
• Portable equipments, due to its compact size
4.1.9 SERVO MOTOR
A servo motor is a type of motor that can rotate with great precision. Normally
this type of motor consists of a control circuit that provides feedback on the current
position of the motor shaft, this feedback allows the servo motors to rotate with great
precision. If you want to rotate an object at some specific angles or distance, then you
use a servo motor. It is just made up of a simple motor which runs through a servo
mechanism. If motor is powered by a DC power supply then it is called DC servo
motor, and if it is AC-powered motor then it is called AC servo motor. For this tutorial,
we will be discussing only about the DC servo motor working. Apart from these
major classifications, there are many other types of servo motors based on the type
of gear arrangement and operating characteristics. A servo motor usually comes with
a gear arrangement that allows us to get a very high torque servo motor in small and
lightweight packages. Due to these features, they are being used in many applications
like toy car, RC helicopters and planes,
Robotics, etc.
Servo motors are rated in kg/cm (kilogram per centimeter) most hobby servo
motors are rated at 3kg/cm or 6kg/cm or 12kg/cm. This kg/cm tells you how much
weight your servo motor can lift at a particular distance. For example: A 6kg/cm Servo
motor should be able to lift 6kg if the load is suspended 1cm away from the motors
shaft, the greater the distance the lesser the weight carrying capacity. The position
54
of a servo motor is decided by electrical pulse and its circuitry is placed beside the
motor.
Servomotors are not a specific class of motor although the term servomotor is
often used to refer to a motor suitable for use in a closed-loop control system. The
motor is paired with some type of encoder to provide position and speed feedback.
In the simplest case, only the position is measured. The measured position of the
output is compared to the command position, the external input to the controller.
If the output position differs from that required, an error signal is generated
which then causes the motor to rotate in either direction, as needed to bring the
output shaft to the appropriate position. As the positions approach, the error signal
reduces to zero and the motor stops.
A servomotor is a rotary actuator or linear actuator that allows for precise

control of angular or linear position, velocity and acceleration. It consists of a suitable
motor coupled to a sensor for position feedback. It also requires a relatively
sophisticated controller, often a dedicated module designed specifically for use with
servomotors.
A servomotor is closed-loop servomechanism that uses position feedback to

control its motion and final position. The input to its control is some signal, either
analog or digital, representing the position commanded for the output shaft.
4.1.9.1 FEATURES AND APPLICATIONS
Supply voltage: 5VDC Control

signal: Analog or D1igital High-
precision positioning.
APPLICATIONS
 Conveyors
 Solar Tracking System
 Antenna Positioning
 Camera Auto Focus
 It is used to measure the speed of the output shaft.
55
 Servo Motor Working Mechanism
 It consists of three parts:
 Controlled device
 Output sensor
 Feedback system
It is a closed-loop system where it uses a positive feedback system to control

motion and the final position of the shaft. Here the device is controlled by a feedback
signal generated by comparing output signal and reference input signal.
Here reference input signal is compared to the reference output signal and the
third signal is produced by the feedback system. And this third signal acts as an input
signal to the control the device. This signal is present as long as the feedback signal
is generated or there is a difference between the reference input signal and reference
output signal. So the main task of servomechanism is to maintain the output of a
system at the desired value at presence of noises.
4.1.9.2 SERVO MOTOR WORKING PRINCIPLE
A servo consists of a Motor (DC or AC), a potentiometer, gear assembly, and

a controlling circuit. First of all, we use gear assembly to reduce RPM and to increase
torque of the motor. Say at initial position of servo motor shaft, the position of the
potentiometer knob is such that there is no electrical signal generated at the output
port of the potentiometer. Now an electrical signal is given to another input terminal
of the error detector amplifier. Now the difference between these two signals, one
comes from the potentiometer and another comes from other sources, will be
processed in a feedback mechanism and output will be provided in terms of error
signal. This error signal acts as the input for motor and motor starts rotating. Now
motor shaft is connected with the potentiometer and as the motor rotates so the
potentiometer and it will generate a signal. So as the potentiometer’s angular position
changes, its output feedback signal changes. After sometime the position of
potentiometer reaches at a position that the output of potentiometer is same as
external signal provided. At this condition, there will be no output signal from the
amplifier to the motor input as there is no difference between external applied signal
and the signal generated at potentiometer, and in this situation motor stops rotating.
56
 INTERFACING SERVO MOTORS WITH MICROCONTROLLERS:
Interfacing hobby Servo motors like s90 servo motor with MCU is very easy.
Servos have three wires coming out of them. Out of which two will be used for
Supply (positive and negative) and one will be used for the signal that is to be sent
from the MCU. An MG995 Metal Gear Servo Motor which is most commonly used
for RC cars humanoid bots etc. The picture of MG995 is shown below:
All servo motors work directly with your +5V supply rails but we have to be
careful on the amount of current the motor would consume if you are planning to use
more than two servo motors a proper servo shield should be designed.
Fig 4.20 : Servo motor
The color coding of your servo motor might differ hence check for your respective
datasheet.
 CONTROLLING SERVO MOTOR:
All motors have three wires coming out of them. Out of which two will be used
for Supply (positive and negative) and one will be used for the signal that is to be
sent from the MCU. Servo motor is controlled by PWM (Pulse with Modulation) which
is provided by the control wires. There is a minimum pulse, a maximum pulse and a
repetition rate. Servo motor can turn 90 degree from either direction form its neutral
57
position. The servo motor expects to see a pulse every 20 milliseconds (ms) and the
length of the pulse will determine how far the motor turns. For example, a 1.5ms pulse
will make the motor turn to the 90° position, such as if pulse is shorter than 1.5ms
shaft moves to 0° and if it is longer than 1.5ms than it will turn the servo to 180°.
Servo motor works on PWM (Pulse width modulation) principle, means its
angle of rotation is controlled by the duration of applied pulse to its Control PIN.
Basically servo motor is made up of DC motor which is controlled by a variable
resistor (potentiometer) and some gears. High speed force of DC motor is
converted into torque by Gears. We know that WORK= FORCE X DISTANCE, in DC
motor Force is less and distance (speed) is high and in Servo, force is High and
distance is less. The potentiometer is connected to the output shaft of the Servo, to
calculate the angle and stop the DC motor on the required angle.
Servo motor can be rotated from 0 to 180 degrees, but it can go up to 210
degrees, depending on the manufacturing. This degree of rotation can be controlled
by applying the Electrical Pulse of proper width, to its Control pin. Servo checks the
pulse in every 20 milliseconds. The pulse of 1 ms (1 millisecond) width can rotate the
servo to 0 degrees, 1.5ms can rotate to 90 degrees (neutral position) and 2 ms pulse
can rotate it to 180 degree.
All servo motors work directly with your +5V supply rails but we have to be
careful about the amount of current the motor would consume if you are planning to
use more than two servo motors a proper servo shield should be designed.
4.2 SOFTWARE REQUIREMENTS
4.2.1 EMBEDDED C
Embedded C is most popular programming language in software field for
developing electronic gadgets. Each processor used in electronic system is
associated with embedded software.
Embedded C programming plays a key role in performing specific function by

the processor. In day-to-day life we used many electronic devices such as mobile
58
phone, washing machine, digital camera, etc. These all device working is based on
microcontroller that are programmed by embedded C.
Fig 4.22 : block diagram representation of embedded system programming
The Embedded C code written in above block diagram is used for blinking the LED
connected with Port0 of microcontroller.
In embedded system programming C code is preferred over other language. Due to

the following reasons:
 Easy to understand
 High Reliability
 Portability
 Scalability
 EMBEDDED SYSTEM PROGRAMMING:
Basic Declaration
Fig 4.22: block diagram of Embedded C Programming development
Function is a collection of statements that is used for performing a specific

task and a collection of one or more functions is called a programming language.
Every language is consisting of basic elements and grammatical rules. The C
language programming is designed for function with variables, character set, data
types, keywords, expression and so on are used for writing a C program.
59
The extension in C language is known as embedded C programming
language. As compared to above the embedded programming in C is also have some
additional features like data types, keywords and header file etc is represented by
#include<microcontroller name.h>.
 BASIC EMBEDDED C PROGRAMMING STEPS:
Let's see the block diagram representation of Embedded C Programming

Steps:
The microcontroller programming is different for each type of operating

system. Even though there are many operating system are exist such as Windows,
Linux, RTOS, etc but RTOS has several advantage for embedded system
development.
 EMBEDDED SYSTEMS : Embedded System is a system composed of hardware,

application software and real time operating system. It can be small independent
system or large combinational system.
Embedded System tutorial includes all topics of Embedded System such as

characteristics, designing, processors, microcontrollers, tools, addressing modes,
assembly language, interrupts, embedded c programming, led blinking, serial
communication, lcd programming, keyboard programming, project implementation
etc.
 SYSTEM : System is a way of working, organizing or performing one or many

tasks according to a fixed set of rules, program or plan.
60
It is an arrangement in which all the unit combined to perform a work together
by following certain set of rules in real time computation. It can also be defined as a
way of working, organizing or doing one or many tasks according to a fixed plan.
An Embedded System is a system that has software embedded into computer-

hardware, which makes a system dedicated for a variety of application or specific
part of an application or product or part of a larger system.
An embedded system can be a small independent system or a large

combinational system. It is a microcontroller-based control system used to perform a
specific task of operation.
An embedded system is a combination of three major components:
 Hardware: Hardware is physically used component that is physically

connected with an embedded system. It comprises of microcontroller
based integrated circuit, power supply, LCD display etc.
 Application software: Application software allows the user to perform
varieties of application to be run on an embedded system by changing the
code installed in an embedded system.
 Real Time Operating system (RTOS): RTOS supervises the way an
embedded system work. It act as an interface between hardware and
application software which supervises the application software and provide
mechanism to let the processor run on the basis of scheduling for
controlling the effect of latencies.
 CHARACTERISTICS OF EMBEDDED SYSTEM:
 An embedded system is software embedded into computer hardware

that makes a system dedicated to be used for variety of application.
61
Embedded system generally used for do specific task that provide
realtime output on the basis of various characteristics of an embedded
system. Embedded system may contain a smaller part within a larger
device that used for serving the more specific application to perform
variety of task using hardware-software intermixing configuration.
 It provides high reliability and real-time computation ability.
Advantages:
 Same hardware can be used in variety of application.

 Lesser power requirement
 Lower operational cost of system
 Provide high performance and efficiency
Disadvantages:
 Developing a system required more time. Due to functional complexity.

Skilled engineers required because one mistake may result in
destroying of complete project.
Designing of an embedded system
 BASIC STRUCTURE OF AN EMBEDDED SYSTEM:
Let's see the block diagram shows the basic structure of an embedded system.
Fig : basic structure of an embedded system.
 Sensor: Sensor used for sensing the change in environment condition and
it generate the electric signal on the basis of change in environment
62
condition. Therefore it is also called as transducers for providing electric
input signal on the basis of change in environment condition.
 A-D Converter: An analog-to-digital converter is a device that converts
analog electric input signal into its equivalent digital signal for further
processing in an embedded system.
 Processor & ASICs: Processor used for processing the signal and data
to execute desired set of instructions with high-speed of operation.
Application specific integrated circuit (ASIC) is an integrated circuit
designed to perform task specific operation inside an embedded system.
 D-A Converter: A digital-to-analog converter is a device that converts
digital electric input signal into its equivalent analog signal for further
processing in an embedded system.
 Actuators: Actuators is a comparator used for comparing the analog input
signal level to desired output signal level for providing the error free output
from the system.
 DESIGN STEPS REQUIRED FOR THE DEVELOPMENT OF EMBEDDED

SYSTEM:
Designing steps required for embedded system are different from the design
process of another electronic system.
 EMBEDDED SYSTEM TOOLS AND PERIPHERALS:
 Compiler: Compiler is used for converting the source code from a

high-level programming language to a low-level programming
language. It converts the code written in high level programming
language into assembly or machine code. The main reason for
conversion is to develop an executable program.
Let's see the operations performed by compiler are:

 Code generation
 Code optimization
 Parsing
 Syntax direct translation
63
 Preprocessing
 Cross-Compiler:
If a program compiled is run on a computer having different operating system

and hardware configuration than the computer system on which a compiler compiled
the program, that compiler is known as cross-compiler.
 Decompiler:
A tool used for translating a program from a low-level language to high-level
language is called a decompiler. It is used for conversion of assembly or machine
code to high-level programming language.
 Assembler:
Assembler is embedded system tool used for translating a computer

instruction written in assembly language into a pattern of bits which is used by the
computer processor for performing its basic operations. Assembler creates an object
code by translating assembly language instruction into set of mnemonics for
representing each low-level machine operation.
Let's see the different debugging tools used in embedded system are:
 Simulators:
Simulator is a tool used for simulation of an embedded system. Code tested

for microcontroller unit by simulating code on the host computer. Simulator is used
for model the behavior of the complete microcontroller in software.
Functions of simulators:
Let's see the functions performed by simulator are:

 It defines the processing or processor device family with various version of
target system.
64
 It monitors the detailed information of a source code and symbolic
arguments as the execution goes for each single step of operation.
 It simulates the ports of target system for each single step of execution.
 It provides the working status of RAM.
 It monitors the response of system and determines the throughput.
 It provides the complete meaning of the present command.
 It monitors the detailed information of the simulator commands entered
from the keyboard or selected from the menu.
 It facilitates synchronization of internal peripherals and delays.
 MICROCONTROLLER STARTER KIT:
For developing an embedded system based project a complete

microcontroller starter kit is required. The major advantage of this kit over simulator
is that they work in real-time operating condition. Therefore it allows the easy
input/output functional verification. Consider a microcontroller starter kit consists of:-
 Hardware Printed Circuit Board (PCB)

 In-System Programmer (ISP)
 Some embedded system tools like compiler, assembler, linker, etc
 Sometimes, there is a requirement of an Integrated Development
Environment (IDE)
The above component available in microcontroller starter kit is completely enough

and the cheapest option available for developing simple microcontroller projects.
 Emulators: An emulator is a software program or a hardware kit which emulates

the functions of one computer system into another computer system. Emulators
have an ability to support closer connection to an authenticity of the digital object.
 It can also be defined as the ability of a computer program in electronic device to
emulate another program or device. It focusing on recreating the original
computer environment and helps a user to work on any type of application or
operating system.
65
 PERIPHERAL DEVICES IN EMBEDDED SYSTEMS:
Communication of an embedded system with an outside environment is done

by using different peripheral devices as a combination with microcontroller.
Let's see the different peripheral devices in embedded system are:-
 Universal Serial Bus (USB)

 Networks like Ethernet, Local Area Network(LAN) etc
 Multi Media Cards (SD Cards, Flash memory, etc)
 Serial Communication Interface (SCI) like RS-232, RS-485, RS-422,
etc
 Synchronous Serial Communication Interface like SPI, SSC and ESSI
 Digital to Analog/ Analog to Digital (DAC/ADC)
 General Purpose Input/Output (GPIO)
 Debugging like In System Programming (ISP), In Circuit Serial
Programming (ICSP), BDM Port, etc
 CRITERIA FOR CHOOSING MICROCONTROLLER:
Choosing a microcontroller is essential process in designing of embedded

system. While selecting a microcontroller, make sure that it meets the system need
and it must be cost effective. We need to decide whether an 8-bit, 16-bit or 32-bit
microcontroller is best suitable for the computing needs of a task.
In addition to above, the following points need to be kept in mind while selecting
a microcontroller:-
 Speed: The operational speed of the microcontroller or the highest

speed microcontroller can support.
 Packaging: Packaging is important for improving the assembling,
space and prototyping of an end-product.
 RAM and ROM: On the basis of operation of embedded system and
memory need for storage data and programs the type of microcontroller
required for designing system is decided.
66
 Count of I/O pins: The number of input and output devices connected
with the system plays an essential role in choosing the type of
microcontroller. Cost per unit: It is important in terms of final cost
of the product in which the microcontroller is to be used.
 Power consumption: Power consumption plays an important role for
maintaining the efficiency of an embedded system
Additional commands are found within the five menus: File, Edit, Sketch,
Tools, and help. The menus are context sensitive, which means only those items
relevant to the work currently being carried out are available.
67
CHAPTER 5
RESULT AND DISCUSSION
5.1 OUTPUT
CONNECTIONS:
The below figure shows the Arduino Mega, RFID tag, RFID reader, GSM module,
16x2 LCD display, servo motor, keypad, buzzer and finger print sensor which was
shown as a complete connection of the hardware components.
Fig 5.1: Overall circuit Connections
STEP:1 REGISTER
68
fifig 5.2: Using RFID Tag
The RFID Card instead of our ATM card to start our Registration process.
Fig 5.3: Using Fingerprint sensor
Here, the Biometric method using fingerprint sensor to access our RDID Card.
69
Fig 5.4: Registration of fingerprint
Fig 5.5 : finger print sensor
Once, our fingerprint is registered then we can easily access all our multiple
accounts using our fingerprint without the hectic of having multiple card and multiple
ATM pins.
Fig 5.6: mobile no Registration process
The registed mobile number to our respected fingerprint and RDIF card using
“REG”.
70
Fig 5.7: Keypad
Keypad is used to operate our hardware components in a feasible way.
Fig 5.8: Mobile number Registration process
By using keypad here we are going to press ”6” in order to access “PH” process
to register our mobile number.
STEP:2 ENTER THE MOBILE NUMBER
71
Fig 5.9: Mobile Number Access
Fig 5.10: Registering our Mobile Number
By registering our mobile number we can access our mobile number to the
respected fingerprint to get otp(One Time Password).
Waiting for OTP
Fig 5.11: otp is generated
72
Fig 5.12: received otp
Thus received our otp to access our bank account to the resigtered Mobile Number.
Fig 5.13: Enter the otp
73
Fig 5.14: verification of otp
By entering the one time password we can access all our accounts that we want to
use in our future now we can do all our transcation process using our smart ATM.
STEP:3 DEPOSIT
 PROCESS OF DEPOSIT
Fig: 5.15: Deposit
Using “(1) DEP” we can start to deposit in our account.
 ACCESS THE BIOMETRIC
74
Fig 5.16: biometric process
Fig 5.17: Usage Biometric Security
 SELECT THE BANK FOR DEPOSIT
Fig: 5.18: Deposit
By pressing “(1) DEP” using our keypad, we can start our process of Depositing
to our bank account.
75
Fig 5.19: selecting SBI bank(1)
By pressing “(1) SBI” in our keypad, we can deposit money in our SBI account.
Fig 5.19: Deposit Rs:5000
STEP:4 WITHDRAWAL
Fig 5.19: WID
Select “(2) WID” to start the process of width drawl in Smart ATM.
76
Fig 5.20: Select the Bank
Select “(1) SBI” to width drawl money from the selected bank account.
Fig 5.21: Enter the Amount
Enter the Amount which you want to width drawl from the bank account.
Fig 5.22: Withdrawal amount and Balance
Now the Withdrawal amount and Balance is visible in LCD Screen and also all
these activities are sent as message to the registered mobile number.
77
STEP :5 CHECK THE BALANCE
Fig 5.23: Checking BAL
 Select “(4) BAL” from the keypad to check the balance from the registered and
deposited bank accounts.
 Select ”(1) SBI” using keypad to check the balance from the bank using the
Smart ATM.
Fig 5.24: view Balance
Now our bank Balance is visible in LED Screen for our convenance.
STEP 6: UNAUTHORIZED
78
Fig 5.25: Place Finger
Fig 5.26: Fraud Access
Fig 5.27: Mismatched finger print
In this case using biometric mismatched fingerprint will be easily dedected by

Smart ATM.
79
Fig 5.28: Un authorized
The LED Screen will display “UN AUTHORIZED” and the buzzer sound will be
audible to everyone to catch the un authorized user.
STEP 7: MESSAGES TO THE REGIATERED MOBILE NUMBER
Fig 5.29: messages to the registered mobile number
From the above figure we can notice that all our Transactions, Registrations, Width
drawl, Checking balances, Addition of bank and Removal of bank accounts will be
sent as a message to the registered mobile number from the respected bank for the
safety of the user.
80
CHAPTER: 6
CONCLUSION AND FUTURE WORK
6.1 CONCLUSION:
There is gradual development in the accessibility of ATM card and necessity of

improving the user friendly and Secure domain in the ATM cards and It evolving
method of using it for multiple bank accounts So, the initiated the Fingerprint Security
for the Project in order to differentiate and stand alone from the previous projects The
fingerprint technology is the most widely accepted and mature biometric method and
is the easiest to deploy and for a higher level of security at the fingertips. It is simple
to install and also it takes little time and effort to acquire one’s fingerprint with a
fingerprint identification device . Thus, finger print recognition is considered among the
least intrusive of all biometric verification techniques. The finger print features are
different for each human being so the user can be identified uniquely. Instead of using
multiple ATM card fingerprint based ATM is safer and secure. There is no worry of
losing ATM card and no need to carry ATM card in your wallet. We just have to use
our fingerprint in order to do any banking transaction. Several cards with different PINS
to them is a difficult process to remember it and sometimes the user can mistyped the
pin with can lead to blockage of ATM card. So this system is proposed to eliminate
such issues and this system can make the user convenient with one card. And instead
of PIN the user use their biometric which make it more secure. The transactions are
same as the logic of a normal ATM. There will be an alert system so the user can
identify their misuse of cards. This reduces the card blockage and other issues like
mismatch of PINs.
6.2 ADVANTAGES
 Single ATM card provides more convince of using

multiple bank transactions.
 Higher security based on the biometric module.
81
6.3 APPLICATIONS
 Single card can be used for multiple bank transaction.

 Transaction
6.4 FUTURE ENHANCEMENT

 Face identification and biometric can be used in the future for bank
transactions.
 Several other security measures can be implemented in the future.
82
REFERENCES
[1] Ahmad, A.W., Jan, N., Iqbal, S. and Lee, C. (2011) Implementation of ZigBee—
GSM Based Home Security Monitoring and Remote Control System. IEEE 54th
International Midwest Symposium on Circuits and Systems, Seoul, 7-10 August
2011, 1-4.
[2] Archana et al., “Enhance the Security in the ATM System with Multimodal
Biometrics and Two-Tier Security”, International Journal of Advanced Research in
Computer Science and Software Engineering 3(10), pp. 261-266, October – 2013.
[3] Biswas S., Bardhan Roy A., Ghosh K. And Dey N.,”A Biometric Authentication
Based Secured ATM Banking System”, International Journal of Advanced
Research in Computer Science and Software Engineering, Volume 2, Issue 4,
April 2012
[4] El-Medany, W.M. and El-Sabry, M.R. (2008) GSM-Based Remote Sensing and
Control System using FPGA. Proceedings of International Conference on
Computer and Communication Engineering, Kuala Lumpur, 13-15 May 2008,
1093-1097.
[5] Golzar, M.G. and Tajozzakerin, H.R. (2010) A New Intelligent Remote Control
System for Home Automation and Reduce Energy Consumption. 4th Asia
International Conference on Mathematical/Analytical Modelling and Computer
Simulation, Kota Kinabalu, 26-28.
[6] "Gsmd – Openmoko". Wiki.openmoko.org. 8 February 2010. Retrieved 22 April
2010.
[7] "GSM UMTS 3GPP Numbering Cross Reference". ETSI. Retrieved 30 December
2009.
[8] G. Vidhya Krishnan, R.Nagarajan, T. Durka, M.Kalaiselvi, M.Pushpa and S.
Shanmugapriya, "Vehicle Communication System Using Li-Fi Technology,"
International Journal of Engineering And Computer Journal of Engineering
Sciences Vol 8, Issue 2, 2017
[9] J.Chandra mohan, R.Nagarajan, K. Satheesh kumar, N.Ajith kumar,
P.A.Gopinath and S.Ranjithkumar, "Intelligent Smart Home Automation and
Security System Using Arduino and Wi-fi,"
83
[10] Karki, James (September 2000). "Signal Conditioning Piezoelectric Sensors"
(PDF). Texas Instruments. Retrieved 2007-12-02.
[11] Kim, Bo-Ra, “Domestic ATM status and meanings”, Payment and Settlement,
and IT, Vol. 44, pp. 76, 2011.
[12] Ms. C. Hemalatha, Mr. R. Nagarajan, P. Suresh, G. Ganesh Shankar and A.
Vijay, “Brushless DC Motor Controlled by using Internet of Things,” IJSTE -
International Journal of Science Technology & Engineering, Volume -3.Issue-09,
pp. 373-377, March- 2017.
[13] Rana, G.M.S.M., Khan, A.A.M., Hoque, M.N. and Mitul, A.F. (2016) Design and
Implementation of a GSM Based Remote Home Security and Appliance Control
System. Proceedings of the 2nd International Conference on Advancesin
Electrical Engineering, Dhaka, 19-21 December 2016, 291-295.
[14] S.Suresh, R.Nagarajan, L.Sakthivel, V.Logesh, C.Mohandass and
G.Tamilselvan, “Transmission Line Fault Monitoring and Identification System by
Using Internet of Things,” International Journal of Advanced Engineering
Research and Science (IJAERS), Vol4.Issue-4, pp. 9-14, Apr- 2017.
[15] Sakr, Sharif. "ARM co-founder John Biggs". Engadget. Retrieved December 23,
2011. "[...] the ARM7- TDMI was licensed by Texas Instruments and designed into
the Nokia 6110, which was the first ARM powered GSM phone."
[16] S.T. Bho sale and Dr. B.S.Sawant “Security in E-Banking via Card Less Biometric
ATMs”, International Journal of Advanced Technology & Engineering Research,
Volume 2, Issue 4, July 2012
[17] Sunil Lohiya “Biometric identification and verification techniques -A future of ATM
Banking System”, Indian Streams Research Journal, Volume 2, Issue. 7, Aug 2012
[18] Yuksekkaya, B., Kayalar, A.A., Tosun, M.B., Ozcan, M.K. and Alkar, A.Z. (2006)
A GSM, Internet and Speech Controlled Wireless Interactive Home Automation
System. IEEE Transactions on Consumer Electronics, 52, 837.
84
85

Chandan

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Chandan

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chandan

Uploaded by

Copyright:

Available Formats

SMART ATM CARD FOR MULTIPLE BANK ACCOUNTS

Submitted in partial fulfillment of the requirements for the award of Bachelor

of Engineering Degree in Electronics and Communication Engineering

DEPARTMENT OF ELECTRONICS AND COMMUNICATION

SCHOOL OF ELECTRICAL AND ELECTRONICS

DEPARTMENT OF ELECTRONICS AND COMMUNICATION

Head of the Department

Dr. T. RAVI, M.E., Ph.D.,

Submitted for Viva voce Examination held on

Internal Examiner External Examiner

We MADHUMITHA C (38130121) and SELVALAKSHMI C (38130200) hereby declare that

PLACE: SIGNATURE OF THE CANDIDATES

We are pleased to acknowledge my sincere thanks to Board of Management of

ATM is an abbreviation of Automated Teller Machine. It is introduced in the year

CHAPTER NO. TITLE PAGE NO

CHAPTER NO TITLE PAGE NO

3 AIM AND SCOPE OF THE PRESENT

3.1 PROPOSED SYSTEM 6

4.1 HARDWARE DESCRIPTION 10

5 RESULT AND DISCUSSION

6 CONCLUSION AND FUTURE WORKS

CHAPTER NO. TITLE PAGE NO

3.1 Block diagram 6

CHAPTER NO TITLE PAGE NO

4.1 Technical Specifications 13

1. ATM - Automatic Teller Machine

An automated teller machine (ATM) is an electronic banking outlet that allows

ATMs are convenient, allowing consumers to perform quick self-service

1.2 SCOPE OF THE PROJECT

1.3 EXISTING SYSTEM

1.3.1 EXISTING SYSTEM DISADVANTAGES

2.1 LITERATURE SURVEY

Title 1: ATM Security using GSM technology.

Authors: Sudhakar Hallur,Manjunath Bajantri, Sagar.

Authors: Moturi Phalguna Satish, Bala Kishore. G

Security in ATM networks is necessary because ATM is widespread and many

Authors: Prof.Shinde S.P, Chingale R.R., Dhane D.C.,Vader P.B.

Title 5: Advance Security System for ATM

Authors: Aman Kumar.

2.2 LITERATURE SUMMARY

3.1.1 PROPOSED SYSTEM ADVANTAGES

3.2 BLOCK DIAGRAM

FINGERPRINT RFID READER

Fig 3.1: Block diagram

3.3 MODULES NAME

3.4 MODULE DESCRIPTION

3.4.1 RFID IDENTIFICATION

Fig 3.2: RFID IDENTIFICATION

Fig 3.3: BIOMETRIC AUTHENTICATION

3.4.3 TRANSACTION PROCESS

Fig 3.4: TRANSACTION PROCESS

Fig 3.5: ALERT MODULE

3.5 BLOCK DIAGRAM DESCRIPTION AND WORKING

MATERIALS AND MATHOD USED

4.1 HARDWARE DESCRIPTION:

Arduino is an open-source electronics platform based on easy-to-use hardware

There are many other microcontrollers and microcontroller platforms available

 Inexpensive - Arduino boards are relatively inexpensive compared to