Development of Hydroponics System and Data

Monitoring Using Internet of Things

2022 IEEE 8th International Conference on Smart Instrumentation, Measurement and Applications (ICSIMA) | 978-1-6654-8800-6/22/$31.00 ©2022 IEEE | DOI: 10.1109/ICSIMA55652.2022.9928901

Nur Anas Sobri Izanoordina Ahmad Siti Marwangi Maharum

Electronics Technology Section Electronics Technology Section Electronics Technology Section
Universiti Kuala Lumpur Universiti Kuala Lumpur Universiti Kuala Lumpur
British Malaysian Institute British Malaysian Institute British Malaysian Institute
Gombak, Selangor, Malaysia Gombak, Selangor, Malaysia Gombak, Selangor, Malaysia
[email protected] [email protected] [email protected]

Zuhanis Mansor Abdul Halim Abd Rahman Azman Abdul Aziz

Communication Technology Section Electronics Technology Section Electronics Technology Section
Universiti Kuala Lumpur Universiti Kuala Lumpur Universiti Kuala Lumpur
British Malaysian Institute British Malaysian Institute British Malaysian Institute
Gombak, Selangor, Malaysia Gombak, Selangor, Malaysia Gombak, Selangor, Malaysia
[email protected] [email protected] [email protected]

Abstract— Hydroponic farming is gaining international humidity, and water are just a few of the important
attention due to its successful stockpiling of water and the environmental elements that this system can regulate. The
development of high-quality foods. Formerly, majority of application system automatically mixes the chosen solution to
gardeners and farmers employed manual techniques and work. produce the desired value. It also gathers data on the quantity
This has give impact on present and future food demand since of solution mixed at the time of planting and can be used to
the traditional farming system will not be able to meet due to determine whether to grow a particular vegetable by
urbanization, natural disasters, and climate change, among estimating the cost of production and calculating its
other factors. Therefore, the goal of this project is to design and profitability [2].
develop the prototype of the hydroponics system and data
monitoring in real time via IoT as well as to test the performance The use of sensors in the greenhouse such as a Wireless
by collecting real-time data. The project used Arduino-Uno to Sensor System is an efficiency in agriculture by sending cloud
control the system and to receive the readings from all of the data and monitoring values such as temperature, light, EC
sensors, such as pH, temperature, EC and water level. The Wi- value and pH value. All data could be monitored via
Fi module will transmit the data wirelessly to ThingSpeak and Thingspeak, including the week's temperature, total energy
Spreadsheet, allowing the farmer to monitor the plant consumed, and all sensor value. It can turn lights on and off
performance through the use of an Internet of Things. Results via the Blynk application [3].
show that the parameters fulfill the requirement by the proper
guideline. Thus, the farmers could monitor the temperature and The use of fuzzy logic control is proposed to automate the
lighting schedules based on the sensors data, which will boost Electrical Conductivity (EC) and pH levels in Hydroponics
plant productivity and address other agricultural issues. Planting. Instead of just using conventional controls, Fuzzy
logic would be utilized to adjust nutrition and pH levels. The
Keywords—hydroponic farming, Agriculture, Internet of proposed approach was validated using mobile vis Blynk [4].
Things, Microcontroller, ThingSpeak, Spreadsheet.
Two farming practices; the classic soil-based method and
I. INTRODUCTION the hydroponic system are compared in order to determine
Due to a variety of man-made factors, including which will best meet present and future demand while using
industrialization, urbanization, natural disasters, climate the fewest resources and at the lowest cost [5]. Cucumber and
change, and the unrestricted use of chemicals in agriculture, Armenian cucumber seeds were both used. Both systems'
soil-based agriculture is currently experiencing difficulties. plant heights were measured, and Analysis of Variance
Hydroponics, also known as soilless agriculture, is a brand- (ANOVA) was used to analyze the data collection. The test
new alternative method of crop production. Plants can be will determine whether or not the type of seeds used, the
grown hydroponically by being submerged in a nutrient-rich planting method, and how they interact affect the plant's
solution of water. Numerous plants, crops, or vegetables can height. The experiment showed that the type of seeds has no
be grown with hydroponics. In general, hydroponically grown discernible influence on the development of the plant. The
produce has superior nutritional value, flavor, and yield hydroponic system has a higher growth rate; however, the
quality than naturally grown produce on soil. Therefore, planting method has a considerable impact on plant growth.
hydroponics would be a superior approach to produce various A compact hydroponic sensor module that utilizes simple
fruits, vegetables, and livestock feed as well as to meet the oscillator circuits to monitor nutrient and water concentrations
future demand for world nutrition[1-2]. was developed in [6]. The system measured and
The project by K. Kularbphettong et all. is to design and communicated using a microprocessor and a sensor put on the
construct an automated system for managing and monitoring board. This research measured oscillating frequency vs. water
plant development in hydroponics, as well as to assess the level, capacitance vs. water level and EC vs. 20 cm water level
impact of employing a prototype of this system. Temperature, capacity.

978-1-6654-8800-6/22/$31.00 ©2022 IEEE

thorized licensed use limited to: AMRITA VISHWA VIDYAPEETHAM AMRITA SCHOOL OF ENGINEERING. Downloaded on April 04,2024 at 07:23:30 UTC from IEEE Xplore. Restrictions app
345 .
 2022 IEEE 8th International Conference on Smart Instrumentation, Measurement and Applications (ICSIMA2022)

The smart agriculture with automation and IoT is also

discussed in [7]. The paper's noteworthy features include a
smart GPS-based remote-controlled robot. The smart
irrigation was connected with data-driven real-time field
control.
Therefore, the development of hydroponics system is
intended to design the real time hydroponics system by
developing the prototype and evaluating its performance. The Fig. 2. a) DHT-22, b) DS18B20 temperature sensor
contribution of this project is to incorporate an intelligent
system specifically in IoT into the agriculture sector in In this project, an EC sensor measures water
Malaysia. With this development of hydroponics system, it conductivity. This sensor may also measure water directly.
can be used by every household in Malaysia by applying this The probe used to generate a voltage between electrodes in
technology and directly reducing the national rate of
water or solution. The voltage drop represents the water's
dependence on imported vegetables and fruits. This
resistance, which is converted to conductivity. Water
hydroponics system could monitor the plant and water quality
consumptions through ThingSpeak and spreadsheet based on Detection Regulator Analog PH Sensor Kit Board Probe
these parameters such as humidity, surrounding temperature, Shield is used for this project. The probe is submerged in
water level, the concentration of ions in the solution and the water as a solution to determine the pH value. The above
pH rate. sensors are shown in figure 3.
As a result, an automated hydroponics system based on the
Internet of Things was developed to aid cultivation, and the
system is capable of adjusting and controlling critical
environmental elements that affect plant growth, such as
temperature, humidity, and water.
II. METHODOLOGY
Fig. 3. a) EC sensor,b) WaterDetection Regulator Analog PH Sensor Kit
This system is developed using related theory and system Board Probe Shield
design concepts to suit the requirements of farmer. The
following approaches were used in the research: This project uses Module Detection Liquid Surface
Depth Height T1592 as its water level sensors as illustrated
in figure 4. In a compact, enclosed location, water level
A. Hardware sensors are used to monitor and control liquid concentration.

Fig. 1. a) Arduino Uno, b) ESP 8266

The Arduino Uno is used as a microcontroller as shown

in figure 1(a) in this particular project. All of the coding will Fig. 4. Water Level Sensor.
be combined, and due to the Arduino standard, it will be able
to read and write all of the data, as well as to ensure that all
of the sensors are functioning as intended. In this project, the B. Software
Arduino ESP 8266 is used as a Wi-Fi module. The ESP 8266
could transmit the sensor data to the ThingSpeak and
Spreadsheets as shown in figure 1(b). Due to the general The Arduino Uno board and the ESP8266 Wi-Fi module
are programmed using the Arduino IDE as shown in figure
specifications, this module could deliver all the data from
5(a). The pH sensor, water level sensor, and other sensors will
each of sensors through Wi-Fi. all work with this software package's source code. The serial
The DHT22 as shown in figure 2(a) is a simple digital monitor output includes additional data such as the attention
temperature and humidity sensor. This sensor uses a powerful value.
moisture sensor and a thermistor to test the ambient air and
delivers a digital signal on the data pin. This project uses the ThingSpeak as in figure 5(b) will visualize all data in this
DHT22 humidity sensor to detect whether the relative project using gauges and graphs. Agriculturalists or users
humidity. could monitor the plant growth based on the displayed data of
The DS18B20 temperature sensor in figure 2(b) pH, EC, water level, temperature, and humidity.
measures the liquid temperature. DS18b20 sensor is chose
due to its robustness and could withstand immersion in
concentrated water solutions at low or high temperatures in a
hydroponics system.

thorized licensed use limited to: AMRITA VISHWA VIDYAPEETHAM AMRITA SCHOOL OF ENGINEERING. Downloaded on April 04,2024 at 07:23:30 UTC from IEEE Xplore. Restrictions app
346
 2022 IEEE 8th International Conference on Smart Instrumentation, Measurement and Applications (ICSIMA2022)

for the plant. A Pak Choi requires a minimum of 450

millilitres of water every day. If the tank's water level falls
below a certain level, the pump will automatically replenish
the tank with water. The water level sensor will be set to level
1, which indicates that the tank's water level is less than 2
litres, and the pump will be activated to feed water to the tank.
Fig. 5. a) Arduino IDE, b) ThingSpeak Level 3 indicates that the water level in the tank has reached
its maximum capacity of 10 litres.
The following figure 6 illustrates the block diagram of the
system consists all required sensors for the design of The characteristics of Pak Choi in hydroponics by
prototype and to be used in the experiments. referring to [9] requires water temperature that is between 55
and 75-degrees Fahrenheit (13°C to 24 °C) as shown in table
1. Therefore, if DS18b20 sensor value is more than 30 degrees
Celsius, the system will turn off the LED to reduce the
temperature and send the data to ThingSpeak as the indication
to bring the temperature down.

TABLE I. THE CHARACTERISTICS OF PAK CHOI

The characteristics of Pak Choi

No
Characteristic Measurements
1 Planting Germiinate from seed

2 Harvesting Full harvest

Fig. 6. Block diagram of the system. 7.3lbs/Foot of
3 Yield
tower/Harvest
Rare, more common are
4 Pest and disease arphids and powdery
The result acquired from the microcontroller, which is an mildew
Arduino Uno and ESP 8266, will be transferred to the
5 pH range 6.0-7.5
ThingSpeak and spreadsheet, as well as a led grow light and
a water and fertilizer pump. 6 EC/PPM 1.5-2.5/750-1250

7 Light hour 12-18

Figure 7 shows the flowchart of the system. The pH
sensor, a water level sensor, a DS18b20 temperature sensor, a 8 Temperature Range:55-75°F
humidity sensor, and an EC sensor, will be connected to the
hydroponics system. The data from all sensors will be
monitored through ThingSpeak. Pak Choi plant will be used
in validating the performance of the system. III. RESULT
The optimal pH range for Pak Choi is 6.0-7.5. If the pH This project involves the development of a prototype that
sensor detects a pH value more than 7.5, the system will could measure pH, water level, temperature, humidity, and EC
communicate with ThingSpeak and add nutrition to the water in real time using ThingSpeak and a spreadsheet. The data will
in order to achieve the appropriate pH value. The pH value is be presented in Thingspeak and will be stored in a
critical in hydroponics due to it determines the availability of Spreadsheet. In order to analyze the factors that could give
nutrients to the growing plants. impact to the plant growth and to determine whether the
growth is compliance with the characteristics of Pak Choi, all
data for each parameters will be graphed.

Fig. 7. The flowchart of the system.

Due to the small-scale project, this project makes use the

water level sensor as the indication for ten-litre water tank.
The ten litres of water are sufficient to serve as a water supply Fig. 8. Parameter value of pH, EC, water level, humidity and temperature
shown in ThingSpeak

thorized licensed use limited to: AMRITA VISHWA VIDYAPEETHAM AMRITA SCHOOL OF ENGINEERING. Downloaded on April 04,2024 at 07:23:30 UTC from IEEE Xplore. Restrictions app
347
 2022 IEEE 8th International Conference on Smart Instrumentation, Measurement and Applications (ICSIMA2022)

The real-time parameters are shown in Figure 8. The

parameter value for pH is 7.5, which is within the range of
the characteristic of Pak Choi. Field 2 is the EC value in real
time data. The EC reading is 1.9 which is within the permitted
range of EC value. According to Pak Choi's characteristic, the
EC values should be in between 1.5 and 2.5. However, if it is
higher than the recommended range, the plant's growth would
be stunted. In the worst scenario, the plant will wither due to
over-fertilization.

The ThingSpeak parameter value for water level is 3,

indicating the tank's maximum capacity of 10 litres. Fig. 10. The result for humidity, temperature, pH, EC and water level for
PakChoi.
However, if the indicator displays as 1, the tank has less than
2 litres of water. EC and pH values will be too high if the Based on figure 10, it shows the graph of Pak Choi
water level is less than 8-10 litres due to the concentration of growth. This is the sampling data for each parameters used in
liquid. this project and the data were taken from 19 to 31st November
2021.
Humidity is displayed as field number 4. The plant could
only absorb a specific amount of humidity and as a result, it Humidity is represented by the blue lines at the top of the
produces less evaporation of water than most plants. If the bar. The humidity experiences instability of the reading in the
plant loses too much water, the stomata will be closed and beginning due to the current weather. The humidity is
halting of photosynthesis. The current humidity level is 100% inversely proportional to the temperature.
due to the plants could not evaporate any water,
The green lines indicate the water temperature in the
Figure 8 depicts water at 28°C. The experiment was held water tank. As this project was developed and tested in the
and tested in a room, thus, the water temperature is between room, therefore the recorded water temperature ware stable.
25°C and 28°C. The suitable temperature for Pak Choi is
between 12.78°C to 29.44°C. The other parameters are the orange lines represents the
pH value, the yellow lines on the bar represent the water
level, and the bottom of the bar line, represents the EC value.
As overall, the parameters meet the requirement of Pak
Choi’s characteristics.

The sow seeds, the prototype and the Pak Choi plant
during the monitoring process can be shown in figure 11.

Fig. 9. Result in Spreadsheet

Figure 9 shows the data for each parameter in

SpreadSheet. The total available data is 25841 entries for 30
days of monitoring process. The data for pH value, the EC
value, the water level in the container, the humidity, and the
water temperature, will be captured in every 17 seconds in
ThingSpeak and Spreadsheet.

The time cycle is set to every 17 seconds since all of the

parameters in this project, such as the pH and EC value, are
crucial. If the plant does not received an adequate suitable
range of pH or EC, it can be assumed that the plant does not
receive enough amount of nutrients for growth.

thorized licensed use limited to: AMRITA VISHWA VIDYAPEETHAM AMRITA SCHOOL OF ENGINEERING. Downloaded on April 04,2024 at 07:23:30 UTC from IEEE Xplore. Restrictions app
348
 2022 IEEE 8th International Conference on Smart Instrumentation, Measurement and Applications (ICSIMA2022)

part of a future study that will expand the system to

incorporate more beneficial and adaptable linked devices.
ACKNOWLEDGMENT
Thank you to Universiti Kuala Lumpur and IERL research
cluster for the conference grant allocation and the facility used
during the project.
REFERENCES

[1] S. Jan et al., “Hydroponics – A Review,” Int. J. Curr. Microbiol. Appl.

Sci., vol. 9, no. 8, pp. 1779–1787, 2020.
Fig. 11. The sow seeds, the prototype and the Pak Choi plant during the [2] I.Ahmad, S.E. Shariffudin, A.F. Ramli, S.M. M. Maharum et al.
monitoring process. "Intelligent Plant Monitoring System Via IoT and Fuzzy System", 2021
IEEE 7th International Conference on Smart Instrumentation,
Measurement and Applications (ICSIMA), 2021.
[3] K. Kularbphettong, U. Ampant, and N. Kongrodj, “An Automated
IV. DISCUSSION AND CONCLUSION Hydroponics System Based on Mobile Application,” Int. J. Inf. Educ.
Technol., vol. 9, no. 8, pp. 548–552, 2019.
[4] J. Pitakphongmetha, N. Boonnam, S. Wongkoon, T. Horanont, D.
People now have a great platform to track and monitor Somkiadcharoen, and J. Prapakornpilai, “Internet of things for planting
in smart farm hydroponics style,” 20th Int. Comput. Sci. Eng. Conf.
their plants and garden surroundings thanks to the Internet of Smart Ubiquitos Comput. Knowledge, ICSEC 2016, 2017.
Things and Smart Hydroponic Systems. The smart irrigation [5] M. Fuangthong and P. Pramokchon, “Automatic control of electrical
system may be controlled by the user via the Blynk app on a conductivity and PH using fuzzy logic for hydroponics system,” 3rd
smartphone, along with the hydroponic system, by Int. Conf. Digit. Arts, Media Technol. ICDAMT 2018, pp. 65–70,
continuously updating the state of the garden. This study thus 2018.
shows a more effective way of controlling and keeping track [6] R. Gashgari, K. Alharbi, K. Mughrbil, A. Jan, and A. Glolam,
of hydroponic system activities than the previous system. “Comparison between growing plants in hydroponic system and soil
based system,” Proc. World Congr. Mech. Chem. Mater. Eng., no.
In conclusion, the hydroponics system was successfully September, 2018.
developed using ThingSpeak and Spreadsheet real-time data [7] T. Nishimura, Y. Okuyama, A. Matsushita, H. Ikeda, and A. Satoh, “A
via the Internet of Things. The technology automatically compact hardware design of a sensor module for hydroponics,” 2017
IEEE 6th Glob. Conf. Consum. Electron. GCCE 2017, vol. 2017-Janua,
controls the level of nutrition and offers a graphical user no. Gcce, pp. 1–4, 2017.
interface for simple maintenance and control. The [8] D. Saraswathi, P. Manibharathy, R. Gokulnath, E. Sureshkumar, and
hydroponics prototype can be developed with this project. In K. Karthikeyan, “Automation of Hydroponics Green House Farming
this study, data including pH, EC, and water temperature have using IOT,” 2018 IEEE Int. Conf. Syst. Comput. Autom. Networking,
been examined and validated to ensure they fit the criteria for ICSCA 2018.
Pak Choi's features. The testing method produced satisfactory [9] ZipGrow TM Best Crops For Hydroponics A Reference Guide For
findings, and the application is practical, which leads to an Modern Farmers,” ZipGrow, [Online]. Available: www.Zipgrow.com.
increase in production.
Data mining techniques will be applied to evaluate and
forecast data regarding the amount and quality of the plant as

thorized licensed use limited to: AMRITA VISHWA VIDYAPEETHAM AMRITA SCHOOL OF ENGINEERING. Downloaded on April 04,2024 at 07:23:30 UTC from IEEE Xplore. Restrictions app
349