Power en October 2015

System pro E power New main distribution switchboards up to 6300A
Contacts
ABB SACE The data and illustrations are not binding. We reserve
1STC803005D0204 - 10 .2015
the right to change the contents of this document with-
A division of ABB S.p.A. out prior notice, in the course of technical development
Automation and Distribution Boards of the product.
Via Italia, 58 Copyright 2015 ABB. All rights reserved.
23846 Garbagnate Monastero (LC) - Italy

Tel: +39 031 3570.111
Fax: +39 031 3570.228
www.abb.com/lowvoltage
Technical catalogue | October 2015
System pro E power

New main distribution switchboards up to

6300A
System pro E power
Technical catalogue
1
Range presentation
2
Structure
3
Internal kits
4
Dedicated solution
5
Main distribution systems
6
Segregations
7
Technical details and certifications
8
Overall dimensions
9
List of codes
ABB Technical catalogue | 1STC803005D0204

ABB SACE Division - Quality, ethics and environmental certification
ABB SACE, a division of ABB S.p.A., has always been at the

forefront when it comes to dedicating consistent resources for
the purpose of attaining its sustainability and environmental
protection goals.
A policy confirmed by acquisition of ISO 9001 quality certification
and ISO 14001 environmental management system certification
by all the corporate plants.
Thanks to use of analysis The Garbagnate Monastero plant has also obtained certification for its QAS (Quality, Environment,
tools like LCA (Life Cycle Safety) integrated management system.
Analysis), assessment All the corporate divisions have always actively pursued policies for environmental management
and improvement of the improvement implemented by rationalizing the use of raw materials and energy, preventing pollution,
environmental performance monitoring air and water quality, reducing noise emissions and the waste created by the production
of the entire life cycle of the processes as well as conducting regular environmental audits with the major suppliers.
products is included in ABB Each of these goals and tasks is the result of a farsighted decision to adopt environmental policies
SACE's design engineering and methods for reducing environmental impact. Already a leading enterprise as to the quality of its
work right from the very products, ABB SACE is also a pacesetter in Italy with regard to these issues.
start.
This guarantees technical
and energy performance
optimization during
operation and control,
as well as reduction of
environmental impact during
the manufacturing phase
and end of life management
process.
ABB: Energy efficiency for sustainable

progress
ABB is actively committed to promoting environmental protection and sustainable
development by providing products and solutions that help to improve the energy
efficiency and productivity of the installations while reducing CO2 emissions.
The ABB SACE website: makes your work easier, develops your
business
- News, to keep you up to date about the latest electrical engineering innovations
- Products, just a simple click for an overview of ABB SACE products 24 hours a day
- Catalogues that you can consult, download and request
- Technical documentation where you can check circuit diagrams, dimensional drawings,
instruction sheets, installation manuals
- Work tools for designing in complete safety
- Training, where you can consult the training catalogue and register for courses online
Technical software Calculation and cost estimate tools www.abb.it/lowvoltage

The ABB SACE website will
e-Design: everyone has a project, ABB has a solution to help you in your daily work with
an innovative approach to the
make it happen. world of low voltage electrical
e-Design is the integrated suite, designed and created by ABB, dedicated to designers, technicians, installations and industrial
engineering companies, panel builders and wholesalers. Thanks to e-Design you can design an automation.
electrical installation and optimize the processing time, while benefiting from a product portfolio you e-Design
can use in synergy and with intuitive and simple functions. e-Design suite is structured with
integrated functional modules,
We would like to highlight several positive features: allowing it to support all
planning stages of an electrical
FLEXIBILITY installation. All solutions are
studied in detail, from electrical
- Interconnected modules accessible during all stages of the project
network dimensioning, to
- Projects that can be reused by all the professionals involved in their creation
switchboard configuration,
through to the final cost estimate
VELOCITY stage.
- You can save, duplicate and edit product and switchboard configurations The registration procedure is
- Calculation of single-line diagrams and automatic dimensioning of conductors and control and very easy and, once completed,
protection equipment you can immediately download
installers and upgrades.
SIMPLICITY
- You can draw single-line diagrams using predefined macros
- User-friendly configuration of switchboards and products
The software comprises four different modules for different purposes. One single process includes
electrical system dimensioning, selection and configuration of products and accessories, switchboard
configuration and cost estimates. Everything is much easier than in the past. Each individual module
allows you to work on the details, but is also closely connected with the other modules. Using
separate modules, design engineers can make a precise calculation of whole electrical system,
then select equipment to suit the established electrical requirements and create a switchboard
configuration. Finally, if the result is not sufficiently feasible, more detailed calculations can be made
with the switchboard engineering module.
The suite’s appealing and brand-
Here are some of the new purpose-made properties that make this process enjoyable:
new look, combined with general
- Easy drawing of single-line diagrams, both as regards power distribution and command and control
optimization of the functions that
circuits have always characterized ABB
- Simple and immediate selection and configuration of products, even for those who are not familiar software, make it an innovative
with ABB products, simply by defining technical features tool, up to date with the
- The automatic user-friendly design process based on the list of devices simplifies one of the most technologies currently available
complex design stages and avoids compatibility errors between products, assembly kits and in the sector.
busbar systems After only a brief introduction,
the user can already design,
- Effective product organization with tree views, so that the user can work methodically, view the
calculate, archive and perform
relevant product immediately and define the switchboards with ease
project planning. No special
- Availability of a dedicated module for busbar configuration CAD skills are required. Software
Well aware of market requirements, ABB now capitalizes on its experience and presents the new operation is based on dialog
e-Design suite as a practical answer to every critical aspect of the design process. boxes. The user is led through
the program.
ABB SACE Division and its environmental protection commitment
Among the enterprises belonging to the Group, ABB SACE is in

the forefront when it comes to dedicating consistent resources
to its sustainable development and environmental protection
goals. A policy confirmed by acquisition of ISO 9001 quality
certification and ISO 14001 environmental management system
certification by all the corporate plants as well as Integrated
Quality, Environment, Safety Management System certification
for the majority of business units.
Each of these goals and Indeed, all the corporate divisions actively pursue policies for environmental management
tasks is the result of a improvement implemented by rationalizing the use of raw materials and energy, preventing pollution,
farsighted decision to adopt monitoring air and water quality, reducing noise emissions and the waste created by the production
environmental policies processes as well as conducting regular environmental audits with the major suppliers.
and methods for reducing
environmental impact. Thanks to use of analysis tools like LCA (Life Cycle Analysis), assessment and improvement of the
Already a leading enterprise environmental performance of the entire life cycle of the products is included in ABB SACE's design
as to the quality of its engineering work right from the very start. This with a view to optimizing the technical and energy
products, ABB SACE is also performance, controlling and reducing environmental impact during the manufacturing phase and
a pacesetter in Italy with allowing the product end of life management process to be defined.
regard to these issues.
ABB: quality of the certified product

ABB dedicates consistent resources for the purpose of attaining its quality and
environmental protection goals, as testified by the following certifications obtained by the
company:
System pro E power
User's guide
Chapter 1 Chapter 6
Range presentation Segregations
Overview, introduction and advantages Segregation kits up to Form 4b available
of the new main distribution switchboard for busbar and breakers with front/rear
range up to 6300A. terminal.
Chapter 2
Chapter 7
Structure
Technical details, certifications and
Distinctive features of the new
configuration examples.
switchboards with selection guides for
Specifications of the new switchboard,
rapid choice of the structure. Ordering
regulatory framework, Italian and
codes for the framework and external
international certifications.
covers.
Chapter 3 Chapter 8
Internal kits Overall dimensions
Assembly kits for the circuit-breakers Overall dimensions of the switchboards
and the accessories available for the new and the relative components available.
switchboard solution.
Chapter 4
Dedicated solution Chapter 9
Assembly kits for CombiLine and InLine List of codes
Analytical list of codes.
Chapter 5
Description of the different busbar system
combinations that can be created.
Selection guides and capacity tables.
System pro E power
Range presentation
Range presentation
Introduction 1/2 1
Advantages 1/4
Flexibility 1/4
Velocity 1/5
Simplicity 1/5
Composition of the series 1/6
ABB Technical catalogue | 1STC803005D0204 1/1

System pro E power
Range presentation
System pro E power, ABB's pioneering new solution for main distribution switchboards
1
with rated current up to 6300A and short-circuit current up to 120kV, meets all plant
requirements depending on the type of installation, required degree of protection and
the electrical and mechanical specifications.
Introduction
Thanks to the new switchboard, ABB can provide complete solutions for main electric power distribution in infrastructures and industries,
in accordance with the regulatory framework. Typical fields of application are airports, subways, hospitals, industrial and residential
estates, ports, tunnels, railways, theatres, etc.
In addition, System pro E power guarantees full synergy with all the other ABB apparatus (i.e. modular circuit-breakers, Tmax T and
XT moulded-case circuit-breakers, Emax 2 air circuit-breakers) while being extremely simple to assemble and ensuring ease of wiring.
Great attention has been made to the wiring requirements, with adequately sized structures and pre-engineered sites for mounting the
horizontal and vertical plastic ducts.
The switchboards comprise the following components:

- Structure: simple and quick to assemble. Stability is ensured thanks to the new double-surface profile of the upright and the new
patented joining system.
- Internal kits: designed to integrate ABB's low voltage products. Save time during the assembly work thanks to the patented new
click-in mounting system.
- Main distribution systems: available in the linear and scaled versions. Allow the busbars to be installed in any position, horizontally or
vertically.
1/2 1STC803005D0204 | ABB Technical catalogue

Main characteristics of the series
1
Compliance with Standard IEC 61439-1-2
Vibration test In accordance with Standard IEC 60068-2-57
Seismic withstand capability test In accordance with Standard IEE Std 693
Rated service voltage Ue up to 1000V AC - 1500V DC
Rated insulation voltage Ui up to 1000V AC - 1500V DC
Rated frequency 50-60Hz
Rated impulse withstand voltage Uimp 12kV
Rated current In up to 6300A
Rated short-time withstand current Icw up to 120kA
Rated peak short-circuit current Ipk up to 264kA
IP protection class IP30, IP31, IP40, IP41, IP65
Functional dimensions Height (mm) 1800, 2000mm
Width (mm) 300, 400, 600, 800, 1000, 1250mm
Depth (mm) 200, 300, 500, 700, 900mm

System pro E power
Range presentation
The range of System pro E power structures can be used to create lots of switchboard configurations while guaranteeing flexibility and
1 a certified product. Up to 120 different configurations can be assembled with a just a few part numbers. This new series features a
structure in hot-dip galvanized sheet steel that guarantees equipotential bonding of the switchboard.
IP protection degrees for all types of applications, i.e. up to IP65, can be obtained. It's the only switchboard to reach such a high value.
Certification was achieved after stringent tests involving the entire configuration (structure, circuit-breakers and busbar system), thus
systems conforming to the new international standard IEC 61439-1-2 can be created by following ABB's instructions.
ABB apparatus can be installed inside the switchboards with high-level integration and optimized use of the available space thanks to
the new modules, i.e. 150mm in height, as well as the usual 200mm modules. The circuit-breakers can be internally separated from
Form 1 to Form 4b.
Advantages
The System pro E power switchboard range is based upon three fundamental criteria that define its practical characteristics and
advantages for the users.
Flexibility
The structure can be assembled to suit different logic sequences.
Just a few part numbers for 120 enclosure sizes.
Can be assembled with or without plinth.
Upright with two different surface levels per side so that different kits can be installed.
New ergonomic handle allowing the door to be opened towards the right or left.
New busbar systems using the same components: cross-pieces, mounting plates and multifunction insulating supports able to house 5
or 10mm thick flat or shaped busbars.
Flexible busbar connections.

Velocity
New mounting plates with rapid click-in system.
1
Panels with ¼-turn screws.
Circuit-breaker kits fixed straight onto the uprights.
Internal segregation partitions created by simply adding accessories in sequence.
New handle allowing different inserts to be housed.
Simplicity
New, simple assembly sequence.
Error-free assembly of the structure, which is perfectly symmetrical.
Modular uprights and cross-pieces joined together by means of a patented new system with axial screws.
Dedicated kits for 3-pole moulded-case circuit-breakers and common kits for 3- and 4-pole moulded case circuit-breakers.
Same front panels for fixed and swing frames, and for screwed and hinged solutions.
Two front panel height sizes available (150 and 200mm) for the DIN rail kit.
All this, plus an ultra-sturdy and safe construction, thanks to the new laser-beam welded upright with 13 folds.

System pro E power
Composition of the series
STRUCTURE EXTERNAL COVERS
Rear Side
Top/Bottom panel panels Door
Functional Internal
dimensions Blind Open(1) bottom Blind Vented Blind Vented Glass Blind
H W D
(mm) (mm) (mm) IP30 to 65 IP65 IP40 IP30 to 65 IP30 to 41 IP30 to 65 IP30 to 41 IP40/41 IP65 IP40/41 IP65
200 n n n n n n n n
300 n n n n n n n n n
300 500 n n n n n n n n n
200 n n n n n n n n n n
300 n n n n n n n n n n n
400 500 n n n n n n n n n n n
600 500 n n n n n n n n n n n
1800
2000
800 500 n n n n n n n n n n n
1000 500 n n n n n n n n n n n
200 n n n n n n n n
1250
(1)
Use the dedicated incoming cable flanges to obtain protection class IP65.

1
KITS FOR APPARATUS MAIN DISTRIBUTION SYSTEM

Modular
circuit- Tmax Series moulded-case Emax 2 Series air
breakers circuit-breakers circuit-breakers Horizontal Vertical
System All
pro M XT1 XT2 XT3 XT4 T4 T5 T6 T7 E1.2 E2.2 E4.2 E6. 2 E6. 2 E6. 2 E6. 2 Top/bottom heights Rear Side
3/4P 4P 4P
neutral neutral neutral D D W D
3/4P 3/4P 3/4P 3/4P 3/4P 3/4P 3/4P 3/4P 3/4P 3/4P 3/4P 3P 50% 100% 50/100% (mm) (mm) (mm) (mm)
n n n
n n n
n n n n
n n n n
n n n n
n n n n n n n n n n n
n n n n n n n n n n n n n
n n n n n n n n n n n n n n
n n n n n n n n n n n n
n n n n n n n n n n n n n n n
n n n n n n n n n n n n n n n n
n n n n n n n n n
n n n n n n n n n n n n n
n n n n n n
n n n n n n
n n n n n n n
n n n n n n n
n n n n n n n n n
n n n n n n

System pro E power
Structure
General information 2/2
Choice of the structure

H=1800mm quick selection guide 2/8
H=2000mm quick selection guide 2/10 2
Guide to the order codes 2/14
Order codes
Frame 2/15
External covers 2/20
Finishing components 2/34
Accessories and spare parts 2/36

System pro E power
General information
The range of System pro E power structures can be used to create lots of switchboard
configurations while guaranteeing scalability, flexibility and a certified product.
2
Structure
The structure can be assembled in different ways. Moreover, assembly is error-free since the uprights and crosspieces are symmetrical.
The structure comprises:
- Uprights and crosspieces
- Plinth and flanges
- Top/Bottom
- Door and panels
To ensure the utmost freedom of choice, flexibility and to save on storage space, the components that form the structure are supplied
loose, each one identified by an order code.
Uprights and crosspieces

The uprights and crosspieces (width and depth) have the same laser-beam welded 13-fold profile and are assembled by means of a
patented new joining system with 3 axial screws that makes the switchboard incredibly sturdy. The uprights are available in galvanized
sheet metal or AISI 304 stainless steel for In >4000A rated current values, able to limit stray currents.
Thanks to its shape, the new profile provides 2 surface levels on the same side to allow different kits to be mounted.
The holes made inside are an important innovation, i.e. the 25mm pitch alternation between a round hole and a square one. Self-
threading screws can be inserted into the round holes while the square hole has been created for fastening kits.
The holes made on the outside are different, since there are two round holes with different diameters able to take self-threading screws
and round cage nuts. The two different types of holes alternate with a 25mm pitch as required by the DIN Standards.
Functional dimensions available Structures with blind door

Type of installation Dimensions W (mm) 300 400 600 800 1000 1250*
Height (functional) 1800, 2000mm DIN modules 12 24 36 48 -
* Double door version with overlapping closing.
Width (functional) 300, 400, 600, 800, 1000, 1250mm
Depth (functional) 200, 300, 500, 700, 900mm

New laser-beam welded upright with 13 folds. Extremely sturdy without being too
heavy.
2
Plinth and flanges
The innovative plinth angle piece featuring a patented “folding” system guarantees high-level mechanical strength and can be fastened
from the inside and outside of the structure. The switchboard can also be ordered without plinth and, if required by the project
specifications or requested by the end customer, the plinth angle piece can be fixed to the structure in a successive stage. The plinth
has an anti-rotation device for easier transport on transpallets. The reinforced version is available on request and allows the switchboard
to be moved on rollers.
Top/Bottom
New types of top/bottom have been used so as to allow cables to enter from above or below, also thanks to the special flanges that
guarantee the desired IP class.
Door and Panels

The doors are available in the glass or blind versions and open through 135° on single units. Door opening through 180° can be
obtained on request. For maximum flexibility and ease of use, the hinges are no longer fixed to the uprights but are supplied in the door
package. The handle is not fixed and allows the user to choose whether the door must open towards the right or left. The handle can
house various types of closing inserts (double tab, key-operated, etc.).
The panels are fixed with TORX screws and come in the RAL7035 orange peel.
Structures with glass door Structures with glass door and internal cable compartment
W (mm) 400 600 800 1000 1250* W (mm) 600 800 1000
DIN modules 12 24 36 48 - DIN modules 12 12/24 24/36
* Double door version with overlapping closing.

System pro E power
General information
Frame
Uprights and crosspieces
- New profile with 2 surface levels on the same side to allow different kits to be mounted.
2
- Uprights and crosspieces in galvanized sheet metal or AISI 304 stainless steel for In >4000A rated current values, able to limit stray
currents.
- Easy to assemble: new joining system with 3 axial screws.
- Extremely sturdy: 13 laser-beam welded folds.
- Small packages.
- Internal kits mounted with a rapid system using 1/4-turn screws.
Plinth
- High-level mechanical strength.
- Can be fixed from the outside and from the inside of the structure.
- Can be fixed to the structure in a successive phase.
- Plinth angle piece with anti-rotation system.
- Bottom can be transported on a transpallet.
New 3-way
connection in New plinth with high-
aluminium. Allows level mechanical
the plinth to be strength. Equipped
assembled and the with anti-rotation
structure to be lifted. system. Thanks to its
Double-profile innovative shape, it
uprights for mounting can be fixed from the
accessories and kits inside and outside of
at different depths. the structure.

2
Structural crosspieces for depth and width

in galvanized sheet metal
Pag........................................................................2/13
Uprights in galvanized sheet metal

Pag........................................................................2/12
Universal angle pieces for plinths in

galvanized sheet metal
Pag........................................................................2/14
Plinth flanges in galvanized sheet metal

painted in RAL 7012 orange peel
Pag........................................................................2/15

System pro E power
General information
External covers
The new design partly reflects ABB's distinctive, classic style while System pro E power adds to the elegant appearance without
forgoing functionality or sturdiness. The family feeling proposed by the versions and accessories in ABB's range is underscored
2 throughout, thereby guaranteeing the utmost flexibility as to assembly. Thanks to the handle, which can house different types of closing
inserts and is supplied with the door hinges (no longer fixed to the upright), a vast range of assembly solutions can be obtained to suit
the customers' requirements. It is impossible to commit errors when assembling the structure. Ease of assembly is guaranteed since
the hinges are no longer already fixed to the uprights but are supplied with the door and panel accessories. Tops and bottoms are not
pre-assembled but supplied separately to allow different incoming-outgoing combinations to be obtained.
The new main distribution switchboards are available in versions with glass or blind doors.
Doors and panels

- Family feeling that reflects in all the versions/applications/installations (glass door, blind door).
- The handle allows different inserts to be used.
- The handle and hinges are supplied disassembled. This allows the customer to choose whether the door must open towards the
right or left.
The handle can

house different
types of closing
inserts and comes
with hinges no
longer fixed to
the uprights, but The stylish handles
supplied with the are customized with
door and panel the ABB logo.
accessories.

Blind top/bottom, open bottom and for
applications without plinth for up to IP65
degree of protection in pickled steel sheet
painted in RAL 7035 orange peel. 2
Pag........................................................................2/16
Glass door or blind door in pickled steel

sheet painted in RAL 7035 orange peel,
up to IP65 degree of protection.
Pag........................................................................2/24
External rear panel in pickled steel sheet

painted in RAL 7035 orange peel, up to
IP65 degree of protection.
Pag........................................................................2/20
External side panel in pickled steel sheet

painted in RAL 7035 orange peel, up to
IP65 degree of protection.
Pag........................................................................2/22
Incoming cable flanges in pickled steel

sheet.
Pag........................................................................2/32

System pro E power
Main distribution boards solutions
H=1800mm quick selection guide
Functional Esternal *
dimensions dimensions FRAME EXTERNAL COVERS
Structure cross-
Uprights pieces H=100mm plinth Top/bottom panels Front/side panels
Galvanized sheet
NEW metal Top/Bottom Bottom Rear panel
Height Height Stainless Without
1800mm 2013mm Galvanized steel and Plinth flanges Blind Open(2) plinth Blind Vented
sheet galvanized
W D W* D* metal sheet metal Front/ Angle Front/ IP30(1) IP30(1)
(mm) (mm) (mm) (mm) In≤4000A In>4000A** Rear Sides pieces Rear Sides IP65 IP40(1) IP65 IP40 IP65 IP40(1) IP30(1)
200 316 PCFM0200 PPFM1020 PTBB3026 PTBB3020 PTBO3020 PBWP3020
PUPM1802
PCFM0300
PPAM0100
PPFM1030
PPEB1836
PPEB1830
PPEA1830
300 500 416 616 PCFM0500 PPFM1050 PTBB3056 PTBB3050 PTBO3050 PBWP3050
PUPM1802
PCFM0400
PPAM0100
PPFM1040
PPEB1846
PPEB1840
PPEA1840
PUPM1802
PCFM0600
PPAM0100
PPFM1060
PPEB1866
PPEB1860
PPEA1860
PUPM1800

PUPM1802
PCFM0800
PPAM0100
PPFM1080
PPEB1886
PPEB1880
PPEA1880
200 316 PCFM0200 PPFM1020 PTBB1026 PTBB1020
PUPM1802
PCFM1000
PPAM0100
PPFM1010
PPEB1816
PPEB1810
PPEA1810
PPRB1820(3)
PPRA1820(3)
PPLB1820(4)
PPLA1820(4)
PUPM1802
PCFM1250
PPAM0100
PPFM1250
200 316 PCFM0200 PPFM1020 PTBB1220

PPIM0100
1250 1366
+
900 1016 PCFM0900 PPFM1090 PTBB1290 PTBO1290 PBWP1290
* The external dimensions include the H=100mm plinth and the panels. (3)
Right rear panel for structures W=1250mm.
** This code has to be used for application with In >4000A. It includes No. 2 stainless steel (4)
Left rear panel for structures W=1250mm.
uprights and No. 2 galvanized sheet metal uprights see pag. 2/15. (5)
Door with overlapping for the double door version.
Consult page 2/12 and 7/2 for selection of the protection class. (6)
Door with handle for the double door version.
In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit, page
(1)
2/22. (7)
Finishing profile vertical internal cable compartment.
(2)
Cables franges page 2/27
> Order codes page 2/13 > Technical details page 7/1 > Overall dimensions page 8/1

2
Glass door Blind door

12/24 36/48 Glass door 12/24/36 mod. DIN 12/24 36/48 Finishing Internal cable Intermed.
Side panel mod. DIN + internal cable compartment mod. DIN profile IP30 Frame for panels compartment (8) upright
Internal
Blind Vented Cable Cable Cable Cable door
comp. comp. comp. comp.
IP30(1) W=200 W=400 W=200 W=400 Special W= W=
IP65 IP40(1) IP30(1) IP65 IP40(1) IP65 IP65 IP40(1) IP40(1) IP65 IP40(1) Vertic. Horz. Fixed fixed Swing Uprights Crosspieces 200 400
PPEB1826 PPEB1820 PCCM0200
PPEB1836 PPEB1830 PPEA1830 PCCM0300
PDLB1836
PDLB1830
PPFH0300

PDLG1846
PDLG1840
PDLB1846
PDLB1840
PPFH0400
PFPS1840
PFPF1840
PFFA1840

PDLG1866
PDLG1860
PDLG1842
PDLG8420
PDLB1866
PDLB1860
PPFH0600
PFPS1860
PFPF1860
PFFA1860

PPCV1800(7)
PUKI1800(9)
PUCM1800
PDCB1820
PDCB1840
PUCS1800
PPFV1800

PDLG1886
PDLG1880
PDLG1862
PDLG1844
PDLG8620
PDLG8440
PDLB1886
PDLB1880
PPFH0800
PFPS1880
PFPF1880
PFFA1880

PPEB1820 PCCM0200
PDLG1816
PDLG1810
PDLG1882
PDLG1864
PDLG8820
PDLG8640
PDLB1816
PDLB1810
PPFH1000
PFPF1810
PFFA1810

PDLG8500(6)
(5)
(5)
PDLB8500(6)
PPFH1200
PPEB1820 PCCM0200
PFPF1812
PFFA1825
PDLB8120
PDLB8120
PPEB1890 PPEA1890 PCCM0900
PCCM... to be ordered when there is an intermediate upright for mounting kit (PUKI....) or an intermediate crosspiece
(8)
for installing busbars horizontally under the top or on the bottom of the (PCKI....) structure or when vertical side partitions
are installed.Not compatible with IP40 PBWP....
PUCM... The front upright is always required.
The rear upright is used for fixing the crosspieces that support the busbars and for fixing the vertical side partitions of the
structure. For In >4000A the rear upright for ICC is PUCS....
The intermediate uprights (PUKI….) are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and
(9)
XT1, XT3 with Direct Rotary Handle only in not segregated structures. Order 2 uprights for the kits. To be ordered (2
pieces ) for segregation structure except for 2b with kits that don’t required PUKI.... To be ordered in case of vertical/
horizontal busbar system pag.3/21.

System pro E power
H=2000mm quick selection guide
Functional Esternal
dimensions dimensions * FRAME EXTERNAL COVERS
Structure cross-
Uprights pieces H=100mm plinth Top/bottom panels Front/side panels
Galvanized sheet
NEW metal Top/Bottom Bottom Rear panel
Height Height Stainless Without
2000mm Galvanized steel and
2213mm Plinth flanges Blind Open(2) plinth Blind Vented
sheet galvanized
W D W* D* metal sheet metal Front/ Angle Front/ IP30(1) IP30(1)
(mm) (mm) (mm) (mm) In≤4000A In>4000A** Rear Sides pieces Rear Sides IP65 IP40(1) IP65 IP40 IP65 IP40(1) IP30(1)
PUPM2002
PCFM0300
PPAM0100
PPFM1030
PPEB2036
PPEB2030
PPEA2030
PUPM2002
PCFM0400
PPAM0100
PPFM1040
PPEB2046
PPEB2040
PPEA2040
PUPM2002
PCFM0600
PPAM0100
PPFM1060
PPEB2066
PPEB2060
PPEA2060
PUPM2000

PUPM2002
PCFM0800
PPAM0100
PPFM1080
PPEB2086
PPEB2080
PPEA2080
PUPM2002
PCFM1000
PPAM0100
PPFM1010
PPEB2016
PPEB2010
PPEA2010
PPRB2020(3)
PPRA2020(3)
PPLB2020(4)
PPLA2020(4)
PUPM2002
PCFM1250
PPAM0100
PPFM1250
200 316 PCFM0200 PPFM1020 PTBB1220

1250 1366
* The external dimensions include the H=100mm plinth and the panels. (3)
Right rear panel for structures W=1250mm.
** This code has to be used for application with In >4000A. It includes No. 2 stainless steel (4)
uprights and No. 2 galvanized sheet metal uprights see pag. 2/15. (5)
Consult page 2/12 and 7/2 for selection of the protection class. (6)
In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit, page
(1)
2/22. (7)
Finishing profile vertical internal cable compartment.
(2)
Cables franges page 2/27

2

12/24 36/48 Glass door 12/24/36 mod. DIN 12/24 36/48 Finishing Internal cable Intermed.
Side panel mod. DIN + internal cable compartment mod. DIN profile IP30 Frame for panels compartment (8) upright
Internal
Blind Vented Cable Cable Cable Cable door
comp. comp. comp. comp.
IP30(1) W=200 W=400 W=200 W=400 Special W= W=
IP65 IP40(1) IP30(1) IP65 IP40(1) IP65 IP65 IP40(1) IP40(1) IP65 IP40(1) Vertic. Horz. Fixed fixed Swing Uprights Crosspieces 200 400
PDLB2036
PDLB2030
PPFH0300

PDLG2046
PDLG2040
PDLB2046
PDLB2040
PPFH0400
PFPS2040
PFPF2040
PFFA2040

PDLG2066
PDLG2060
PDLG2042
PDLG8420
PDLB2066
PDLB2060
PPFH0600
PFPS2060
PFPF2060
PFFA2060

PPCV2000(7)
PUKI2000(9)
PUCM2000
PDCB2020
PDCB2040
PUCS2000
PPFV2000

PDLG2086
PDLG2080
PDLG2062
PDLG2044
PDLG8620
PDLG8440
PDLB2086
PDLB2080
PPFH0800
PFPS2080
PFPF2080
PFFA2080

PPEB2020 PCCM0200
PDLG2016
PDLG2010
PDLG2082
PDLG2064
PDLG8820
PDLG8640
PDLB2016
PDLB2010
PPFH1000
PFPF2010
PFFA2010

PDLG2500(6)
(5)
(5)
PDLB2500(6)
PPFH1200
PPEB2020 PCCM0200
PFPF2012
PFFA2025
PDLB2120
PDLB2120
PPEB2090 PPEA2090 PCCM0900

((8)
PCCM... to be ordered when there is an intermediate upright for mounting kit (PUKI....) or an intermediate crosspiece
for installing busbars horizontally under the top or on the bottom of the (PCKI....) structure or when vertical side partitions
are installed.Not compatible with IP40 PBWP....
PUCM... The front upright is always required.
The rear upright is used for fixing the crosspieces that support the busbars and for fixing the vertical side partitions of the
structure. For In >4000A the rear upright for ICC is PUCS....
The intermediate uprights (PUKI….) are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and
(9)
XT1, XT3 with Direct Rotary Handle only in not segregated structures. Order 2 uprights for the kits. To be ordered (2
pieces ) for segregation structure except for 2b with kits that don’t required PUKI.... To be ordered in case of vertical/
horizontal busbar system pag.3/21.

System pro E power
Realization of the different IP protection class example

IP30 IP40
2
IP31 IP41
+ +
IP30 IP40
IP31 IP41
+ +
IP65

Examples of use
PUCM.... or PUCS...
PCCM.... 2
Structure with rear

Back to back
cable compartment: to
structures
be realized by means
of 2 crosspieces for
structure PCCM.... and
2 uprights for internal
cable compartment
PUCM.... o PUCS....
200 200
500
700
500
700
900
Structure with double

internal cable compartment:
to be realized by means of
crosspieces for internal cable
compartment PCCS.... and
uprights for internal cable
compartment PUCM.... o
PUCS....
200
200 800
400 1000

System pro E power
Guide to the order codes
The new code is formed by 4 letters standing for English terms and 4 numbers, without
spaces in between.
2 RANGE IDENTIFIER
The first letter of all the codes of the new main distribution
switchboard “P” stands for “power”. Thus the new product is clearly
identified by the same initial used for all new components of ABB's
System pro E power
TYPE OF PRODUCT AND CHARACTERISTICS

The second letter in the code indicates the type of product or component
of the switchboard. The third and fourth letters describe the characteristics
or material in more detail.
U = Upright
C = Crosspieces
P = Plinth, Panel, Profile
T = Top
B = Bottom
D = Door
K = Kit
P = Upright, Profile
C= Cable compartment
F = Frame, Flanges, Finishing
A= Plinth angle pieces
I = Intermediate
B= Bottom
W= Without plinth
E = External cover
D= Double tab insert
M= Metal/Galvanized sheel metal

S = Stainless steel
B= Blind
O= Open
P = Plinth
A= Vented
G= Glass
H= Horizontal
V = Vertical
T = Top
MEASUREMENTS
The last 4 numbers usually refer to one of the component's measurements
or to several dimensions concerning the code. In certain cases, if the last
number is 6, it refers to the IP65 protection class.
P U P M 1 8 0 0

Order codes - Frame
Uprights – Galvanized sheet metal

Upright formed by a closed profile made of galvanized sheet metal. The uprights include 8 already assembled
3-way joints, 8 already assembled axial screws and 16 loose axial screws. For applications with In ≤4000A.
Dimensions
Description H (mm)
Order
code
Codice
ABB
Package/
No. pcs
2
No.4 galvanized sheet metal uprights 1800 PUPM1800 1STQ007033A0000 1/4
NEW Uprights for enclosure In>4000A

The uprights include 8 already assembled 3-way joints, 8 already assembled axial screws and 16 loose axial
screws. For applications with In >4000A.
Dimensions
Order Codice Package/
Description H (mm) code ABB No. pcs
No.2 stainless steel uprights and no.2
1800 PUPM1802 1STQ002031A0000 1/4
galvanized sheet metal uprights
No.2 stainless steel uprights and no.2
2000 PUPM2002 1STQ002032A0000 1/4
galvanized sheet metal uprights
Examples of use
Galvanized sheet metal In ≤4000A Uprights for enclosure In>4000A
PUPM1800 PUPM1802
PUPM2000 PUPM2002
Metal sheet Stainless steel

(AISI304)
Metal sheet
Metal sheet

System pro E power
Order codes - Frame
Structure crosspieces
Depth and width crosspieces for structures.
Dimensions
(mm)
Order ABB Package/
2 Description W D code code No. pcs
Width crosspieces galvanized sheet metal
No.4 width crosspieces galvanized sheet metal 300 PCFM0300 1STQ007037A0000 1/4
Depth crosspieces galvanized sheet metal
Width crosspieces stainless steel
No.4 width crosspieces in stainless steel 300 PCFS0300 1STQ007206A0000 1/4
Depth crosspieces stainless steel
No.4 depth crosspieces in stainless steel 200 PCFS0200 1STQ009174A0000 1/4
> Quick selection guides page 2/8 > Technical details page 7/1 > Overall dimensions page 8/1

Uprights for internal cable compartment – Galvanized sheet metal
Upright formed by a closed profile in galvanized sheet metal for internal cable compartment with fixing brackets.
Dimensions
No.1 galv. sheet metal upright for cable
2
1800 PUCM1800 1STQ007742A0000 1/1
compartment
No.1 galv. sheet metal upright for cable
2000 PUCM2000 1STQ007743A0000 1/1
compartment
Uprights for internal cable compartment – Stainless steel

Upright formed by a closed profile in AISI 304 stainless steel for internal cable compartment with fixing brackets.
For applications with In >4000A, the rear internal cable compartment uprights has to be in stainless steel.
Dimensions
No.1 stainless steel upright for cable com-
1800 PUCS1800 1STQ007749B0000 1/1
partment
No.1 stainless steel upright for cable com-
2000 PUCS2000 1STQ007750B0000 1/1
partment
The front upright is always required. The rear upright is used for fixing the crosspieces that support the busbars and for fixing the
vertical side partitions of the structure. In case of In>4000A the rear internal cable compartment upright has to be in stainless steel.
Applications examples
Examples of use
Galvanized sheet metal In≤4000A Uprights for enclosure In>4000A
PUCM1800 PUPM1800 PUCS1800 PUPM1802
PUCM2000 PUPM2000 PUCS2000 PUPM2002
Metal sheet Metal sheet Stainless steel Stainless steel
(AISI304) (AISI304)
PUCM1800 PUCM1800
PUCM2000 PUCM2000
Metal sheet Metal sheet
Metal sheet Metal sheet

System pro E power
Order codes - Frame
Crosspieces for internal cable compartment

2 Crosspieces for internal cable compartment in galvanized sheet metal.
Dimen-
sions
Description D (mm) code ABB No. pcs
No.2 galvanized sheet cable cont. crosspieces 200 PCCM0200 1STQ007744A0000 1/2
No.2 stainless steel cable cont. crosspieces 700 PCCS0700 1STQ007751A0000 1/2
No.2 stainless steel cable cont. crosspieces 900 PCCS0900 1STQ007752A0000 1/2
To be ordered when there is an intermediate upright for mounting kit PUKI.... or an intermediate crosspiece for installing busbars
horizontally under the top or on the bottom of the PCKI.... structure or when vertical side partitions are installed.
Not compatible with IP40 PBWP....
Applications examples

200mm Crosspieces for structures – Galvanized sheet metal
Allows the creation of a cable compartment with D=200mm at the back of the stuctures. To be assembled with 2
intermediate uprights for internal cable container PUCM.... o PUCS....
Dimensions
Order Codice Package/ 2
Description W (mm) code ABB No. pcs
No.2 galvanized sheet crosspieces for
400 PCCM0400 1STQ001336B0000 1/2
structures
600 PCCM0600 1STQ001337B0000 1/2
structures
800 PCCM0800 1STQ001338B0000 1/2
structures
1000 PCCM1000 1STQ001339B0000 1/2
structures
PPAM0100 Universal angle pieces for plinths in galvanized sheet metal

Not pre-assembled to the structure. New angle piece with high mechanical strength. Can be fixed from the outside
and from the inside of the structure even at a later date. Equipped with anti-rotation system and bottom that can
be transported with a transpallet.
Dimen-
sions Order ABB Package/
Description H (mm) code code No. pcs
No.4 plinth angle pieces 100 PPAM0100 1STQ007048A0000 1/4
PPAM0200
No.8 plinth angle pieces H=100mm 200 PPAM0200 1STQ007207A0000 1/4
pre-assembled*
*Order no. 2 pieces of H=100mm covering flange kits to complete the H=200mm plinth.

System pro E power
Order codes - Frame
“L” covers for plinth angle-pieces

Used for covering the sides of the plinth when the flanges are not used.
Dimensions Order ABB Package/
2 No.4 angle-piece covers 100 PCPA0004 1STQ008109A0000 1/4
PPIM0100 Intermediate plinth

Intermediate plinth only for structures W=1250mm
No.2 intermediate plinths 100 PPIM0100* 1STQ007208A0000 1/2
No.4 intermediate plinths
200 PPIM0200* 1STQ007209A0000 1/2
H=100mm pre-assembled*
* Order no. 2 pieces of H=100mm covering flange kits to complete the H=200mm intermediate plinth.
PPIM0200
Brackets for fixing to the floor

The kit allows the floor or on container fixing of the structure by means of M12 screws.
Order ABB Package/
Description code code No. pcs
No.4 floor fixing brackets ZN1041 1STQ006833A0000 1/4

Plinth flanges
Side and front/rear plinth flanges H=100mm RAL 7012.
Dimensions (mm)
Order ABB Package/
Description W D code code No. pcs 2
Front/rear plinth flanges
No.2 plinth flanges 300 PPFM1030 1STQ007050A0000 1/2
Side plinth flanges
Brackets for bottoms without plinth

The kit allows the mounting of the angle pieces PPAM…. from the inside of the structure or the application of
enclosures without plinth when combined with the proper internal bottom PBWP…. IP40 or the other bottom codes
available that have to be cut according to the drilling indication in chapter 8.
Order ABB Package/

No. 4 brackets for bottoms without plinth PBRB0004 1STQ008127A0000 1/4

System pro E power
Order codes - External covers
Blind Top/Bottom IP65 – Pickled sheet steel

Pickled sheet steel with IP65 gasket. The article comprises one single component that can be used as either a top
or bottom. In order to purchase both the top and the bottom, please order two quantities of the same code or two
different top/bottom codes according to the desired design of the structure. The code includes four M12x20 screws.
2 Dimensions (mm)
Order ABB Package/
Description W D code code No. pcs
Blind Top/Bottom IP65 300 200 PTBB3026 1STQ007074A0000 1/1

NEW Open bottom IP65 – for internal cable container
Pickled sheet steel with IP65 gasket. In order to reach IP65 protection degree, use the dedicated fixed cable
incoming flanges both for equipment compartment and internal cable compartment.
Use the fixed cable incoming flanges with the same dimension as the equipment compartment PFCF…. Pag 2/27.
2
Dimensions (mm) Order ABB Package/
Open bottom IP65
Open bottom 600+200mm 800 300 PTBO8231 1STQ002076B0000 1/1
Blind fixed flange IP65 for internal cable container
Blind fixed flange 200 300 PFCF2031 1STQ002048B0000 1/1
Example:
Base IP65 W 800mm D 500mm with 200mm W internal cable container.
Order:
n°1 PTBO8251 open bottom W 800mm (600 + 200 ) D 500mm
n°1 PFCF2051 blind fixed flange for internal cable contaioner W 200mm D 500mm
n°1 PFCF6050 blind fixed flange for equipment compartment W 600mm D 500mm
Top/bottom IP65 for corner structures

different top/bottom codes according to the desired design of the structure. It requires the use of the relating kit
PSCS0579 in case of joining corner structures.
To fix the busbars system use the universal crosspiece PCRM2013 that has to be cut according to the needs and the brackets
PBCB0002.

System pro E power
Blind Top/Bottom IP30, IP40 – Pickled sheet steel

Pickled sheet steel without gasket. In order to reach IPX1 protection degree it is necessary to add the proper top
sealing kit, page 2/23.
The article comprises one single component that can be used as either a top or bottom. In order to purchase both
2 the top and the bottom, please order two quantities of the same code or two different top/bottom codes according
to the desired design of the structure. The code includes four M12x20 screws.
Dimensions
(mm)
Order ABB Package/
Blind Top/Bottom IP30, 40 300 200 PTBB3020 1STQ007107A0000 1/1
Realization of the different IP protection class:
IP30: IP30, IP40 panels + vertical finishing profiles for structure or external cable container PPFV.... or vertical finishing profiles for
internal cable container PPCV.... and horizontal finishing profiles PPFH....
IP31: add to IP30 codes the top sealing kit PKPT....
IP40: IP30, IP40 panels + blind door IP40/IP41 PDLB.... or glass door IP40/IP41 PDLG....
IP65: dedicated IP65 codes

Top sealing kit IP31/IP41
Profiles for IP31/IP41 for top.
Dimensions (mm)
Order ABB Package/
Description W D code code No. pcs 2
Top sealing kit IP31/IP41 300 200 PKPT3020 1STQ008061A0000 1/1

System pro E power
NEW Top sealing kit IP31/IP41*

Dimensions
(mm)
2 Description W D
Order
code
ABB
code
Package/
No. pcs
N.2 roof profiles for single column 200 PKST0200 1STQ001905B0000 1/2
N.1 roof profile for side by side column 200 PKDT0200 1STQ001917B0000 1/1
N.1 roof profile for back to back column 250 PKDT0250 1STQ001918B0000 1/1
Roof profiles for corner structure 500 500 PKAT5050 1STQ001939B0000 1/4
*Available from January 2016.

Open Top/Bottom
Pickled sheet steel with holes. The code comprises one single component that can be used as either a top or
bottom. In order to purchase both the top and the bottom, please order two quantities of the same code or two
different top/bottom codes according to the desired design of the structure.
In order to reach IP65 protection degree, use the dedicated fixed cable incoming flanges PFCF….; in order to reach 2
IP40 protection degree, use the dedicated swinging cable incoming flanges PFCS…. at page 2/25.
The use of the single open top/bottom without flanges does not guarantee any degree of protection IP. The open top/
bottom, associated with sliding flanges, is incompatible with crosspieces assembled inside the cable compartment.
Dimensions (mm)
Order ABB Package/
Open Top/Bottom 300 200 PTBO3020 1STQ007135A0000 1/1

System pro E power
Fixed incoming cable flange

Fixed incoming cable flange in sheet metal to use in conjunction with the open bottom to guarantee IP65 protection
class. With internal cable compartment crosspieces it is necessary to mount the fixed flange first.
2 Dimensioni (mm)
Order ABB Package/
Fixed incoming cable flange 300 200 PFCF3020 1STQ007658A0000 1/1
Fixed incoming cable flange 1250 900 2xPFCF6090 1STQ007674A0000 1/1
Sliding incoming cable flanges in sheet metal

Sliding incoming cable flanges in sheet metal to use in conjunction with the open bottom to guarantee IP40 protec-
tion class. It is not possible to assemble the sliding flanges in structures with internal cable compartment.
Dimensioni (mm)
Order ABB Package/
No.2 sliding flanges 400 500 PFCS4050 1STQ007699A0000 1/2
400
600
No.2 sliding flanges 1250 900 2xPFCS6090 1STQ007707A0000 1/2
800
1000

Internal bottom IP40
Internal galvanized steel bottom with special brackets kit included (special brackets kit available also as spare part
with the code PBRB0004). In order to reach IPX1 protection degree it is necessary to add the proper top sealing
kit PKPT..., page 2/25.
2
Dimensions
(mm)
Order ABB Package/
Internal bottom 300 200 PBWP3020 1STQ007171A0000 1/1
1250

System pro E power
External blind rear panel IP65

Pickled sheet steel with gasket and plugs IP65.
Dimensions
2 (mm)
Order ABB Package/
Description H W code code No. pcs
Blind rear panel IP65 1800 300 PPEB1836 1STQ007577A0000 1/1
External blind rear panel IP30, IP40

sealing kit PKPT..., page 2/25.
Dimensions
(mm)
Order ABB Package/
Blind rear panel IP30, IP40 1800 300 PPEB1830 1STQ007608A0000 1/1
Blind rear panel IP30, IP40 right PPRB1820 1STQ007616A0000 1/1
1800 1250
left PPLB1820 1STQ007617A0000 1/1
2000 1250
left PPLB2020 1STQ007628A0000 1/1


External vented rear panel IP30
In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit PKPT..., page 2/25.
Dimensions
No.
Vented
(mm)
Order ABB Package/ 2
Description grates H W code code No. pcs
Vented rear panel IP30 2 1800 300 PPEA1830 1STQ007630A0000 1/1
Vented rear panel right PPRA1820 1STQ007639A0000 1/1
IP30/31 with gasket 6 1800 1250
left PPLA1820 1STQ007640A0000 1/1
Vented rear panel IP30 right PPRA2020 1STQ007649A0000 1/1
with gasket 4 2000 1250
left PPLA2020 1STQ007650A0000 1/1
External blind side panel IP65

Pickled sheet steel with gasket and plugs IP65. The code refers to one single side panel.
Dimensions
(mm)
Order ABB Package/
Description H D code code No. pcs
Blind side panel IP65 1800 200 PPEB1826 1STQ007575A0000 1/1

System pro E power
External blind side panel IP30, IP40

Pickled sheet steel with gasket. The code refers to one single side panel. In order to reach IPX1 protection degree
it is necessary to add the proper top sealing kit PKPT..., page 2/25.
Dimensions
2 (mm)
Order ABB Package/
Blind side panel IP30, IP40 1800 200 PPEB1820 1STQ007607A0000 1/1
External vented side panel IP30

Pickled sheet steel without gasket. The code refers to one single side panel. For IP40 order the dedicated grate
PGPP0040. In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit PKPT...,
page 2/25.
Dimensions
(mm)
No. Vented Order ABB Package/
Description grates H D code code No. pcs
Vented side panel IP30 2 1800 300 PPEA1830 1STQ007630A0000 1/1

IP40 grate for Vented external panels

Accessory for Vented panels. Allows IP40 protection class to be obtained. Order the quantity on the basis of the
number of grates on the panel. In order to reach IPX1 protection degree it is necessary to add the proper top
Order ABB Package/

No. IP40 grates for Vented panels PGPP0040 1STQ008090A0000 1/2

Glass door IP65
Pickled sheet steel with gasket. Opens through 135° (single column). Complete with 4 hinges to be screwed onto
the uprights, 4 door closing brackets with cover and handle. Handle and hinges provided (not pre-assembled for
complete reversibility). Doors can be mounted both on the front and on the back of the enclosures.
Dimensions (mm)
2
Cable
No. DIN compartment Order ABB Package/
Description modules H W W code code No. pcs
Glass door
Glass door IP65 12 1800 400 PDLG1846 1STQ007303A0000 1/1
Glass door for structures with internal cable compartment
Glass door IP65 12 1800 600 200 PDLG1842 1STQ007304A0000 1/1
Glass door IP40

Pickled sheet steel without gasket and 4 rubber overlapping plugs. Opens through 135° (single column). Complete
with 4 hinges to be screwed onto the uprights, 4 door closing brackets with cover and handle. Handle and hinges
provided (not pre-assembled for complete reversibility). In order to reach IPX1 protection degree it is necessary
to add the proper top sealing kit PKPT..., page 2/25. Doors can be mounted both on the front and on the back
of the enclosures.
Dimensions (mm)
Cable
Glass door
Glass door for structures with internal cable compartment

System pro E power
Blind door IP65

complete reversibility). Doors can be mounted both on the front and on the back of the enclosures. Reinforcing
2 tubes for W>400mm
Dimensions
(mm)
No. DIN Order ABB Package/
Description modules H W code code No. pcs
Blind door IP65
- 1800 300 PDLB1836 1STQ007347A0000 1/1
cable compartment
Blind door IP65 12 1800 400 PDLB1846 1STQ007348A0000 1/1
Blind door IP65
- 2000 300 PDLB2036 1STQ007354A0000 1/1
cable compartment
Blind door IP40

provided (not pre-assembled for complete reversibility). In order to reach IPX1 protection degree it is necessary to
add the proper top sealing kit PKPT..., page 2/25. Doors can be mounted both on the front and on the back of the
enclosures. Reinforcing tubes for W>400mm
Dimensions
(mm)
Blind door IP40 cable
- 1800 300 PDLB1830 1STQ007361A0000 1/1
compartment
Blind door IP40 cable
- 2000 300 PDLB2030 1STQ007368A0000 1/1
compartment

Double doors IP40 for W=1250mm structures
Doors with overlapping to use with the door with handle to create switchboards with double doors. Handle and
hinges provided (not pre-assembled for complete reversibility). Doors can be mounted both on the front and on
the back of the enclosures. In order to reach IPX1 protection degree it is necessary to add the proper top sealing
kit, page 2/25. 2
Dimensions
(mm)
Order ABB Package/
Door with overlapping
Blind door with overlapping IP40 1800 250 PDLB8120 1STQ007366A0000 1/1
Blind door with overlapping IP40 2000 250 PDLB2120 1STQ007373A0000 1/1
Door with handle
Glass door with handle IP40 1800 1000 PDLG8500 1STQ007335A0000 1/1
Glass door with handle IP40 2000 1000 PDLG2500 1STQ007346A0000 1/1
Blind door with handle IP40 1800 1000 PDLB8500 1STQ007367A0000 1/1
Blind door with handle IP40 2000 1000 PDLB2500 1STQ007374A0000 1/1
Horizontal/vertical front closing profiles IP30

Profiles for IP30/IP31 pickled sheet painted RAL 7012. In order to reach IPX1 protection degree it is necessary to
add the proper top sealing kit PKPT..., page 2/25.
Dimensions (mm)
Order ABB Package/
Finishing profiles vertical structure and external cable compartment
No.2 vertical profiles IP30 1800 PPFV1800 1STQ008059A0000 1/2
Finishing profile vertical internal cable compartment
No.1 profile vertical IP30 1800 PPCV1800 1STQ009294A0000 1/1
Finishing profiles horizontal structure and external cable compartment
No.2 horizontal profiles IP30 300 PPFH0300 1STQ008053A0000 1/2

System pro E power
Order codes - Structure finishing components
Internal door for internal cable compartment

Internal door in pickled steel sheet for cable compartment IP30.
Dimensions (mm)
Order ABB Package/
2 Description H W code code No. pcs
Blind door for internal cable
1800 200 PDCB1820 1STQ007753A0000 1/1
compartment
1800 400 PDCB1840 1STQ007754A0000 1/1
compartment
2000 200 PDCB2020 1STQ007755A0000 1/1
compartment
2000 400 PDCB2040 1STQ007756A0000 1/1
compartment
Internal door for external cable compartment

Dimensions (mm)
Order ABB Package/
Blind door for external cable
1800 300 PDCB1830 1STQ008086A0000 1/1
compartment
1800 400 PDCB1844 1STQ008087A0000 1/1
compartment
2000 300 PDCB2030 1STQ008088A0000 1/1
compartment
2000 400 PDCB2044 1STQ008089A0000 1/1
compartment
Pre-configured plastic cable gland flanges IP65

Allow numerous cables to be installed and guarantee that the components inside the switchboards are protected.
EV0114 The inserts have a membrane through which the cable can be easily pushed without the need for tools. IP65 pro-
tection class is guaranteed over the entire flange regardless of the number of cables installed. Cable clamp, and
cable gland with cable clamp can also be installed.
RAL 7035 grey colour; operating temperature from -20 °C to +125 °C, IP65 protection class in accordance with
EV0116
EN 60529 specifications.
Dimensioni
(mm)
Order ABB Package/
Pre-configured modular flange IP65
No.1 pre-configured incoming cable flange
for 18 cables (Ø min/max 8/14mm) and 10 214 90 EV0114 1STQ006545A0000 1/1
cables (Ø min/max 4/10mm)
No.1 pre-configured incoming cable flange
for 30 cables (Ø min/max 4/10mm), 2
214 90 EV0116 1STQ006546A0000 1/1
cables (M20 Ø min/max 7/13mm) and 2
cables (M25 Ø min/max 8/17mm)

194 Flanges with adaptable plastic cable gland inserts IP65
Thanks to the frame and inserts available, the flange can be adapted to suit the size, quantity and position of the cables
62
installed. The inserts have a membrane through which the cable can be easily pushed without the need for tools.
EV0117 IP65 protection class is guaranteed over the entire flange regardless of the number of cables installed. Cable clamp,
and cable gland with cable clamp can also be installed. 2
RAL 7035 grey colour; operating temperature from -20 °C to +125 °C, IP65 protection class in accordance with
EN 60529 specifications.
Dimensioni
(mm)
Order ABB Package/
Adaptable modular flanges
No.1 flange frame for incoming cables to
214 90 EV0117 1STQ006547A0000 1/1
create with individual inserts
Inserts for adaptable flanges
No.10 (ten) 68x68mm inserts for 4
incoming cables, 2 cables (M25 Ø min/
68 68 EV0119 1STQ006548A0000 1/1
max 8/17mm), 2 cables (M16 Ø min/max
5/10mm)
No.10 (ten) 68x68mm inserts for 1 incom-
68 68 EV0121 1STQ006549A0000 1/1
EV0119 EV0121 ing cable type M32 / M40 / M50
68 68 EV0123 1STQ006550A0000 1/1
ing cables (Ø min/max 8/14mm)
ing cables, 2 (Ø min/max 10/20) and 2 (Ø 68 68 EV0124 1STQ006551A0000 1/1
min/max 20/30mm)
EV0123 EV0124 34 68 EV0125 1STQ006552A0000 1/1
34 68 EV0126 1STQ006553A0000 1/1
34 68 EV0127 1STQ006554A0000 1/1
EV0125 EV0126 EV0127

System pro E power
Order codes - Accessories and spare parts
Plastic pocket for documents

Complete with adhesive parts for fixing to the door.
Order ABB Package/

2
Plastic pocket for A4 documents EV1075K 1STQ008199A0000 1/1
A4
Closing systems
Can replace the standard closing systems of the external doors. The inserts are interchangeable and can be easily
replaced by loosening just one nut.
PHLS0010
Order ABB Package/
Handle
Standard lever handle (spare) PHLS0010 1STQ008126A0000 1/1
Padlockable lever handle (spare) PHLL0020 1STQ008128A0000 1/1
PHLL0020
Inserts
Yale insert+key for external door, single door
AA6200 1STQ009135A0000 1/1
version
E739 ronis insert+key for external door,
AA8004 1STQ009136A0000 1/1
single door version
FIAT type insert for lever handle PIFH0020 1STQ008122A0000 1/1
AD1058 AA6200 FIAT key AA1570 1STQ009137A0000 1/1
AA8004
6.4 triangular male insert on Ø 7.6 for
PITH0064 1STQ008119A0000 1/1
external door, single door version
Key for triangular insert AA1560 1STQ009138A0000 1/1
7 square male insert for external door,
PISH0007 1STQ008120A0000 1/1
single door version
PIFF0020 AA1570
Insert 8mm hex socket type for
PIEH0008 1STQ008121A0000 1/1
standard handle (Key not available)
Double tab insert for closing handle/box PIDH0010 1STQ008118A0000 1/1
Key zama for double tab insert AD1058 1STQ009134A0000 1/1
PITH0064 AA1560 Box with double tab insert in plastic with key
EV1008 1STQ000956A0000 1/1
for inner door (Nema TYPE 12)
One-code Yale insert for inner door EV1036 1STQ000974A0000 1/1
Ronis 405 insert and key for standard handle PIRH0405 1STQ008123A0000 1/1
PISH0007 Ronis 455 insert for EV1008 EV1037 1STQ000975A0000 1/1

PIEH0008
Ronis insert 2432 and key for standard
PIRH2432 1STQ002030B0000 1/1
handle NEW
Key
Ronis 455 insert and key for standard handle PIRH0455 1STQ008124A0000 1/1
EV1036 Ronis 1242 insert and key for standard

PIRH1242 1STQ008125A0000 1/1
EV1037 handle
3mm double tab insert for inner door EV1039 1STQ000976A0000 1/1

Kit for joining structures
The kit for joining structures is composed of different brackets and a gasket for the maintenance of the IP protection
degree and allows both a side-by-side and a back-to-back joining of structures.
Order ABB Package/
Description code code No. pcs 2
Kit for joining structures side by side / back to back PSBS0065 1STQ008113A0000 1/8
Kit for joining corner structures PSCS0579 1STQ009185A0000 1/12
NEW Brakets for circuit-breaker kit

Order ABB Package/
No.2 brakets for circuit-breaker kit PBKT0002 1STQ002008B0000 1/2
NEW Brakets for intermediate upright

Order ABB Package/
No.2 brakets for intermediate upright PKMI0002 1STQ002021B0000 1/2
PEBL0004 Eyebolts for lifting

Allow wired switchboards to be lifted. Made of steel treated with a white passivated galvanizing process.
PBRL0002
Order ABB Package/
No.4 steel M12 eyebolts PEBL0004 1STQ008112A0000 1/4
Lifting reinforcements
Used for handling several adjacent switchboards.
Order ABB Package/
No.2 lifting reinforcements for adjacent switchboards PBRL0002 1STQ008116A0000 1/2

System pro E power
Wall-mounting brackets
PBWF0002 Allow the switchboards to be fixed to a wall
Order ABB Package/
2 No.2 wall-mounting brackets PBWF0002 1STQ008115A0000 1/2
Screws
Order ABB Package/
No.1000 self-perforating 4.2x13mm cross-head
EV1100 1STQ001005A0000 1/1000
screws
No.1000 self-perforating 4.2x19mm cross-head
EV1101 1STQ001006A0000 1/1000
screws
No.24 screws for side/rear panels PSCP0024 1STQ009182A0000 1/24
No.24 screws 1/4 turn with washers PCSS0024 1STQ009183A0000 1/24
No.20 M5 Torx screws and nylon washers L=16mm EV0103 1STQ006608A0000 1/20
No.20 M6 Torx screws and nylon washers L=16mm EV0104 1STQ006609A0000 1/20
Spray paints
RAL7035 colour spray paint for structures VB7035 1STQ008129A0000 1/1
RAL7012 colour spray paint for plinths VB7012 1STQ001064A0000 1/1
Axial screws for uprights

Axial screws for 3 way joint uprights.
Order ABB Package/
No.16 axial screws for uprights PSAF0016 1STQ008110A0000 1/16
Hinges for standard doors

Order ABB Package/
No.4 hinges for standard door PHDR0004 1STQ009159A0000 1/4
No.4 180° opening hinges PHFR4180 1STQ009158A0000 1/4

System pro E power
Internal kits
General information
Kits for Emax 2 air circuit-breakers 3/2
Kits for Tmax XT and Tmax T moulded-case circuit-breakers 3/3
Kits for System Pro M e modular circuit-breakers
XT1 and XT3 moulded-case circuit-breakers 3/3
Kits for OT switch-disconnectors 3/3
Quick selection guides 3

Recommended installation solutions 3/4
Kits for moulded-case circuit-breakers 3/10
Kits for air circuit-breakers 3/18
Order codes
Internal kits 3/20
Accessories and spare parts 3/40

System pro E power
General information
The switchboards can be assembled very quickly even when extremely complex apparatus is involved thanks to the innovative internal
kits designed for System pro E power. They match perfectly with the new uprights and crosspieces with double fixing levels and are
available for air and moulded-case circuit-breakers, switch-disconnectors, modular circuit-breakers and internal segregation partitions.
The main advantages are:

- Quick click-in fixing system with ¼ turn screws
- Common kits for 3- and 4-pole moulded-case circuit-breakers installed horizontally
3 - Same front panels for fixed and swing frames, and for screwed and hinged solutions
- Two front panel height sizes available (150 and 200mm) for DIN rail kits.
Simple, effective systems for fixing the kits save time when the switchboards are assembled.
Kits for Emax 2 air circuit-breakers

Available for all sizes from E1.2 to E6.2 in fixed and withdrawable versions. Sturdy and simple, they meet the requirements of all
applications, from 630 to 6300A.

Kits for Tmax XT and Tmax T moulded-case circuit-breakers
Available for XT1 to XT4 and T4 to T7 circuit-breakers. The major innovations include the common kit for 3- and 4-pole circuit-breakers
installed horizontally and the 150mm height panel, which allows more circuit-breakers to be installed in the same unit than the 200mm
panel solution.
Kits for System Pro M and XT1 and XT2 moulded-case circuit-breakers
Available for all modular circuit-breakers and for XT1 and XT2 moulded-case circuit-breakers The DIN rail provides two pre-engineered 3
assembly positions, corresponding to the depth of System pro M and Tmax XT circuit-breakers, respectively. The 150mm height panel
also allows more circuit-breakers to be installed in the same unit than the 200mm panel solution.
Kits for OT switch-disconnectors

Available for OT up to 1600 A both in the vertical and horizontal versions.
Quick click-in fixing system with ¼ turn screws Plate for Tmax XT and Tmax T moulded-case circuit-breakers
Holes with shaped openings for rear

connections for 3P circuit-breakers; pre-cut
holes included for 4P
Holes for front terminals, with flexible

insulated connections that proceed
behind the plate for fixed circuit-
breakers (for W=400mm only Tmax
XT1 and XT2): all terminal covers for
segregated versions are required
2
1
Holes for front terminals with connections routed from

the side: these can be anchored by fixing the dedicated
accessory to the round holes (allowing flexible busbars to
be fastened). The clamps can be threaded through the
rectangular holes.

System pro E power
Quick selection guides
Recommended installation solutions

Type of structure/installation
Form 1, Form 2b switchboard
Modular and Tmax D=200mm D=300mm D=500mm
moulded-case circuit-breakers HORIZ. VERT. HORIZ. VERT. ORIZZ.
System pro-M n n
TmaxXT1 front terminals with side exit fixed n n n n n
plug-in
3 fixed+diff n n
n
n
n
n
n
n
rear/front terminals with rear exit fixed n n n n n
plug-in n n n
Tmax XT2 front terminals with side exit fixed n n n n n
plug-in n n n
withdrawable n n n
withdrawable+ diff n n n
fixed+diff n n n n n
plug-in n n n
withdrawable n n n
plug-in n n n
rear/front terminals with rear exit fixed n n n
plug-in n n n
plug-in n n n
withdrawable n n n
plug-in n n n
withdrawable n n n
Tmax T4 front terminals with side exit fixed n n n n n
fixed+diff n n n
plug-in n n n
plug-in+diff n n n
withdrawable n n n
plug-in n n n
plug-in+diff n n n
withdrawable n n n
fixed+diff n n n
withdrawable (4) n n n
rear/front terminals with rear exit (1) fixed n n n n n
withdrawable n n n
Tmax T7 front terminals with side exit fixed n n n
withdrawable
rear/front terminals with rear exit fixed n n
withdrawable
Emax air circuit-breakers
Emax E1.2 front and rear terminals fixed n n n
rear terminals withdrawable n
Emax E2.2 rear terminals fixed
withdrawable
withdrawable
withdrawable
(1)
Front terminals with rear exit, only Form 1. (4)
Only Form 1.
> Order codes page pag. 3/20 > Technical details page 7/1 > Overall dimensions page 8/1

(1)
Front/rear connections.
Form 2a-3a, Form 3b, Form 4b switchboard
D=700mm D=900mm D=500mm D=700mm D=900mm
VERT. HORIZ. VERT. HORIZ. VERT. HORIZ. VERT. HORIZ. VERT. HORIZ. VERT.
n n n n n n
n n n n n
n
n
n
n
n
n
n
n
n
n
3
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n n n n
n n n n n n n n n n
n n n n (3) n n
n n n n
n (2) n n (2) n
n (2) n n (2) n
n n
n n
(2)
For busbar systems from 3200A. (3)
The busbar systems cannot be placed behind the breakers.

System pro E power
Recommended installation solutions for accessorized apparatus

Tmax moulded-case circuit-breakers D=200mm D=300mm D=500mm
with Direct Rotary Handle operating mechanism or motor operator HORIZ. VERT. HORIZ. VERT. HORIZ.
3 plug-in n n n
withdrawable n n n
plug-in n n n
withdrawable n n n
withdrawable (2) n n n
rear/front terminals with rear exit (1) fixed n n n
withdrawable n n n
Tmax T7 front terminals with side exit fixed n n
withdrawable
withdrawable
Tmax XT1 front terminals with side exit fixed n n n
plug-in n n n
plug-in n n n
plug-in n n n
withdrawable n n n
plug-in n n n
withdrawable n n n
plug-in n n n
plug-in n n n
plug-in n n n
withdrawable n n n
plug-in n n n
withdrawable n n n
(1)
Front terminals with rear exit, only Form 1.
(2)
Only Form 1.

VERT. HORIZ. VERT. HORIZ. VERT. ORIZZ. VERT. ORIZZ. VERT. ORIZZ. VERT.
n n n n n
n n n n n
n n n n n 3
n n n n n
n n n n n
n n n n n
n n n n n n n n n
n n n n n
n n n n n n n n n
n n n n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n
n n n n n

System pro E power
Recommended installation solutions for accessorized apparatus

Tmax interlocked, interlocked motor-operated D=200mm D=300mm D=500mm
moulded-case circuit-breakers HORIZ. VERT. HORIZ. VERT. HORIZ.
3 plug-in n n
withdrawable n n
plug-in n n
withdrawable n n
withdrawable (4) n n
rear/front terminals with rear exit (3) fixed n n
withdrawable
Tmax T7 front terminals with side exit fixed
withdrawable
rear/front terminals with rear exit fixed n
withdrawable
Tmax XT1 front terminals with side exit fixed n n
plug-in n n
plug-in n
plug-in n n
withdrawable n n
plug-in n n
withdrawable n n
plug-in n n
plug-in n
plug-in n n
withdrawable n n
plug-in n n
withdrawable n n
Emax air circuit-breakers
Emax E1.2 front and rear terminals fixed n n n
rear terminals withdrawable n
withdrawable
withdrawable
withdrawable
(3)
Front terminals with rear exit, only Form 1.
(4)
Only Form 1.

VERT. HORIZ. VERT. HORIZ. VERT. HORIZ. VERT. HORIZ. VERT. HORIZ. VERT.
n n
n n n n n
n n
n n 3
n n
n n n n n
n n n n n
n n n n n
n n
n n
n n n n
n n n n
n n n n
n n n n n n n n n
n n n n n n n n
n n
n n
n n n n n
n n n n n
n n
n n
n n
n n n n n
n n n n n
n n n n n
n n
n n
n n n n n
n n n n n
n n
n n
n n
n n n n n
n n n n n
n n n n n
n n n n n n n n n n
n n n n (2) n n
n n n n
n (1) n n (1) n
n (1) n n (1) n
n n
n n
(1)
For busbar systems from 3200A. (2)
The busbar systems cannot be placed behind the breakers.

System pro E power
Kits for moulded-case circuit-breakers

Tmax XT horizontal installation
To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm. Intermediate uprights are
not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary Handle only in non-segregated structures. Order
the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels. For D=300mm structures, consult the details on page 3/21.
NON-ACCESSORIZED CIRCUIT-BREAKERS ACCESSORIZED CIRCUIT-BREAKERS

Dimensions Dimensions Fixed
(mm) Front or rear (mm) No. CB per Residual Direct
No. CB CB No. compart- current Rotary
Front or rear per connections poles H W ment device Handle
CB No. compart-
XT1 3P 200 400 1 PHBX1323
connections poles H W ment Fixed Plug-in Withdrawable
3P 200 600 1 PHCX1323
XT1 3P 4P 150 400 1 PHBX1401
3P 4P 150 400 1 PHBX1405
3P 4P 150 600 1 PHCX1401 3P 4P 150 600 1 PHCX1405
3P 4P 150 800 1 PHDX13 01 3P 4P 200 400 1 PHBX1423(2) PHBX1105
3P 4P 200 600 1 PHCX1423(2) PHCX1105
3P 4P 200 400 1 PHBX1101 PHBX1407
3P 4P 500 400 2
3P 4P 200 600 1 PHCX1101 PHCX1407 3P 4P 500 600 2
3P 4P 200 800 1 PHDX1401 4P 200 800 1 PHDX1423
XT2 XT2 3P 4P 200 400 1 PHBX2423(2) PHBX2405
3P 150 400 1 PHBX2301
3P 4P 200 600 1 PHCX2423(2) PHCX2405
3P 150 600 1 PHCX2301 3P 4P 200 800 1 PHDX2423(2)
3P 4P 200 400 1 PHBX2401 PHBX2407 PHBX2310 (1) 3P 4P 250 400 1
3P 4P 200 600 1 PHCX2401 PHCX2407 PHCX2310 (1) 3P 4P 250 600 1
3P 4P 500 400 2
3P 4P 200 800 1 PHDX2401 PHDX2407
3P 4P 500 600 2
3P 4P 250 400 1 PHBX2410 4P 250 800 1
3P 4P 250 600 1 PHCX2410 XT3 3P 150 400 1 PHBX3305
XT3 3P 150 600 1 PHCX3305
3P 150 400 1 PHBX3301(3)
3P 4P 200 400 1 PHBX3405
3P 150 600 1 PHCX3301 3P 4P 200 600 1 PHCX3405
3P 4P 200 400 1 PHBX3401(3) PHBX3407 3P 4P 500 400 2
3P 4P 200 600 1 PHCX3401 PHCX3407 3P 4P 500 600 2
4P 250 400 1 PHBX3423(4)
3P 4P 200 800 1 PHDX3401 PHDX3407 4P 250 600 1 PHCX3423
XT4 3P 150 400 1 PHBX4301(3) 4P 200 800 1 PHDX3423
3P 150 600 1 PHCX4301 XT4 3P 4P 200 400 1 PHBX4423(2) (4) PHBX4405
3P 4P 200 600 1 PHCX4423(2) PHCX4405
3P 4P 200 400 1 PHBX4401 (3)
PHBX4407
3P 4P 200 800 1 PHDX4423(2) PHDX4405
3P 4P 200 600 1 PHCX4401 PHCX4407 3P 4P 250 400 1
3P 4P 200 800 1 PHDX4401 PHDX4407 3P 4P 250 600 1
3P 4P 500 400 2
3P 4P 250 400 1 PHBX4410
3P 4P 500 600 2
3P 4P 250 600 1 PHCX4410 4P 250 800 1
(1)
Only 3 poles (1)
Only 3 poles
(2)
Only 4 poles (2)
Only 4 poles
(3)
Not compatible with high terminal covers. Compatible residual current devices: RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC Sel.. XT2-XT4
(3)
Type A. For XT1-XT3 fixed with residual current device high terminal covers are not available.
(4)
Not compatible with high terminal covers.
For fixed and withdrawable 3P breakers Tmax XT, non accessorized and mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P
mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked
or interlocked motor-operated kits, it is necessary to order the quantity of flanges equal to the quantity of breakers.

3
Plug-in Withdrawable
Interlocked Residual Direct Interlocked Residual Direct Interlocked
Motor motor- current Rotary Motor motor- current Rotary Motor motor-
operator Interlocked operated device(3) Handle operator Interlocked operated device(3) Handle operator Interlocked operated
PHBX1404 PHBX1427 PHBX1409

PHCX1404 PHCX1427 PHCX1409
PHBX1422 PHBX1424 PHBX1422 PHBX1424
PHCX1422 PHCX1424 PHCX1422 PHCX1424
PHBX2404 PHBX2427 PHBX2409 PHBX2300(1) PHBX2312(1)

PHCX2404 PHCX2427 PHCX2409 PHCX2300(1) PHCX2312(1)
PHDX2404
PHBX2428(2) PHBX2400 PHBX2412
PHCX2417(2) PHCX2400 PHCX2412
PHBX2402 PHBX2424 PHBX2431 PHBX2424 PHBX2425 PHBX2425
PHCX2402 PHCX2424 PHCX2431 PHCX2424 PHCX2425 PHCX2425
PHDX2428

PHBX3422 PHBX3424 PHBX3422 PHBX3424
PHCX3422 PHCX3424 PHCX3422 PHCX3424

PHDX4404
PHBX4428(2) PHBX4400 PHBX4412
PHCX4417(2) PHCX4400 PHCX4412
PHBX4402 PHBX4424 PHBX4431 PHBX4424 PHBX4425 PHBX4425
PHCX4402 PHCX4424 PHCX4431 PHCX4424 PHCX4425 PHCX4425
PHDX4428

System pro E power

Tmax T horizontal installation
To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm. Intermediate uprights
are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary Handle only in non-segregated structures.
Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels. For D=300mm structures, consult the details on page 3/21.

(mm) (mm)
Front or rear No. CB Front or rear No. CB Residual Direct
circuit- breaker No. per circuit- breaker No. per current Rotary
connec. poles H W compart. Fixed Plug-in Withdraw. connections poles H W compart. device (4) Handle
T4 3P 150 400 1 PHBT4301(3) T4 3P 4P 200 400 1 PHBT4406(3)
3P 150 600 1 PHCT4301 3P 4P 200 600 1 PHCT4423(2) PHCT4406
3P 4P 200 400 1 PHBT4406(3) 3P 4P 600 400 2
3P 4P 200 600 1 PHCT4406 3P 4P 600 600 2
T5 400A 3P 4P 600 800 2
3P 200 400 1 PHBT5326
T5 400A 3P 200 400 1
3P 200 600 1 PHCT5326 3P 200 600 1
3P 200 800 1 PHDT5326 3P 200 800 1
3P 300 400 1 PHBT5314 3P 300 400 1
3P 300 600 1 PHCT5314 3P 300 600 1
3P 300 800 1 PHDT5314 3P 300 800 1
400A/630A 3P 200 400 1 PHBT5306(3) 400A/630A 3P 200 400 1 PHBT5306(3)
3P 200 600 1 PHCT5306 3P 200 600 1 PHCT5306
3P 200 800 1 PHDT5306 3P 200 800 1 PHDT5306
400A 3P 4P 250 400 1
400A 3P 4P 250 400 1 PHBT5426
3P 4P 250 600 1
3P 4P 250 600 1 PHCT5426 3P 4P 250 800 1
3P 4P 250 800 1 PHDT5426 3P 4P 350 400 1
3P 4P 350 400 1 PHBT5414 3P 4P 350 600 1
3P 4P 350 600 1 PHCT5414 3P 4P 350 800 1
3P 4P 350 800 1 PHDT5414 3P 4P 600 400 2
400A/630A 3P 4P 250 400 1 PHBT5406(3) 3P 4P 600 600 2
3P 4P 600 800 2
3P 4P 250 600 1 PHCT5406
400A/630A 3P 4P 250 400 1 PHBT5406(3)
3P 4P 250 800 1 PHDT5406 3P 4P 250 600 1 PHCT5406
630A 3P 200 600 1 PHCT5307 n 3P 4P 250 800 1 PHDT5406
3P 4P 250 600 1 PHCT5407 3P 4P 600 600 2
3P 300 600 1 PHCT5310 n 400A 4P 250 600 1 PHCT5423
T6 3P 300 600 1 PHCT6301(4) 4P 250 800 1 PHDT5423
T6 3P 300 600 1 PHCT6305 (6)
3P 300 800 1 PHDT6301
3P 300 800 1 PHDT6305
3P 4P 350 600 1 PHCT6401(4) PHCT6314 (1) n 3P 4P 350 600 1 PHCT6405
3P 4P 350 800 1 PHDT6401(4) PHDT6314 (1) n 3P 4P 350 800 1 PHDT6405
3P 4P 500 600 1 PHCT6410 n 3P 4P 500 600 1
3P 4P 500 800 1 PHDT6414 n 3P 4P 500 800 1
T7 3P 300 600 1 PHCT7329 3P 4P 700 600 2
3P 300 800 1 PHDT7329 T7 3P 300 600 1 PHCT7329
3P 400 600 1 3P 300 800 1 PHDT7329
3P 400 800 1 3P 4P 350 600 1 PHCT7420
3P 4P 350 600 1 PHCT7420 3P 4P 350 800 1 PHDT7420
3P 4P 400 600 1
3P 4P 350 800 1 PHDT7420
3P 4P 400 8 00 1
3P 4P 500 600 1 PHCT7430 * 3P 4P 500 600 1
3P 4P 500 800 1 PHDT7430 * 3P 4P 500 800 1
(1)
Only 3 poles n
Front terminals, only Form 1
(1)
Only 3 poles
(2)
Only 4 poles * Only rear terminals
(2)
Only 4 poles
(3)
Not compatible with high terminal covers. (3)
Not compatible with high terminal covers.
(4)
T6 1000A front terminals in width 800mm.

3
Interlocked Direct Interlocked Direct Interlocked

Motor motor- rotary Motor motor- Rotary Motor motor-
operator Interlocked operated handle operator Interlocked operated Handle operator Interlocked operated
PHBT4404
PHCT4404
PHBT4402
PHCT4402 PHCT4403
PHDT4402 PHDT4403
PHBT5326 PHBT5309
PHCT5326 PHCT5309
PHDT5326 PHDT5309
PHBT5314 PHBT5312
PHCT5314 PHCT5312
PHDT5314 PHDT5312
PHBT5304
PHCT5304
PHDT5304
PHBT5426 PHBT5409
PHCT5426 PHCT5409
PHDT5426 PHDT5409
PHBT5414 PHBT5412
PHCT5414 PHCT5412
PHDT5414 PHDT5412
PHBT5404
PHCT5404 PHCT5427(5) PHCT5425 PHDT5411
PHDT5404 PHCT5425 PHDT5411
PHCT5402 PHCT5403 PHCT5431 PHCT5432
PHCT6304 (6)
PHDT6304
PHCT6404 PHCT6314(1) n PHCT6312(1) n
PHDT6404 PHDT6314(1) n PHDT6312(1) n
PHCT6410 n PHCT6412 n
PHDT6414 n PHDT6412 n
PHCT6402 PHCT6403 PHCT6425 n PHCT6411 n
PHCT7329 PHCT7329 PHCT7329
PHDT7329 PHDT7329 PHDT7329
PHCT7420
PHDT7420
PHCT7418 PHCT7418
PHDT7418 PHDT7418
PHCT7430 * PHCT7430 * PHCT7430 * PHCT7430 *
PHDT7430 * PHDT7430 * PHDT7430 * PHDT7430 *
(4)
Compatible residual current devices: RC222 for T4 and T5. n
(5)
Only 630 A. * Only rear terminals
(6)
T6 1000A front terminals in width 800mm.

System pro E power

Tmax XT vertical installation
To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm. Intermediate uprights are
not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary Handle only in non-segregated structures. Order
the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels. For D=300mm structures, consult the details on page 3/21.

Front Dimensions Front Dimensions Fixed
or rear (mm) or rear (mm)
circuit- No. circuit- No. Residual
breaker No. adjacent breaker No. adjacent current
connections poles H W CB Fixed Plug-in Withdrawable connections poles H W CB device(2)
XT1 3P 4P 300 400 1 PVBX1401 PVBX1407 XT1 3P 4P 300 400 1 PVBX1423 (1)
3P 4P 300 600 1 PVCX1401 PVCX1407
3P 300 600 4 PVCX1301 PVCX1707 3P 4P 300 600 1 PVCX1423 (1)
3P 300 600 4 PVCX1301
3P 4P 300 800 4 PVDX1807 XT2 3P 4P 300 400 1
XT2 3P 4P 300 400 1 PVBX2401 PVBX2407 PVBX2410
3P 4P 300 600 1 PVCX2401 PVCX2407 PVCX2410 3P 4P 300 600 1
3P 4P 300 600 3 PVCX2701 PVCX2707
4P 350 400 1 PVBX2423
3P 4P 300 800 4 PVDX2801 PVDX2807
XT3 3P 4P 300 400 1 PVBX3401 PVBX3407 4P 350 600 1 PVCX2423
3P 300 600 3 PVCX3707
XT3 3P 4P 300 400 1
3P 4P 300 600 1 PVCX3401 PVCX3407
3P 300 600 3 PVCX3301 PVCX3607
3P 4P 300 600 1
3P 300 600 3 PVCX3301
3P 300 800 4 PVDX3807
4P 400 400 1 PVBX3423
3P 4P 300 800 3 PVDX3707
XT4 3P 4P 300 400 1 PVBX4401 4P 400 600 1 PVCX3423
3P 4P 300 600 1 PVCX4401
XT4 3P 4P 300 400 1
3P 4P 300 600 2 PVCX4601
3P 300 600 3 PVCX4701
3P 4P 300 600 1
3P 4P 300 800 3 PVDX4701
3P 300 800 4 PVDX4801
3P 4P 350 400 1
3P 4P 350 400 1 PVBX4407 PVBX4410
3P 350 600 3 PVCX4707 3P 4P 350 600 1
3P 4P 350 600 1 PVCX4407 PVCX4410
3P 4P 350 600 2 PVCX4607 4P 400 400 1 PVBX4423
3P 350 800 4 PVDX4807
4P 400 600 1 PVCX4423
3P 4P 350 800 3 PVDX4707
Only 4 poles.
(1)
Compatible residual current devices: RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC Sel..
(2)
XT2-XT4 Type A. For XT1-XT3 fixed with residual current device high terminal covers are
not available.
For fixed and withdrawable 3P breakers Tmax XT, non accessorized and mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P
mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked
or interlocked motor-operated kits, it is necessary to order the quantity of flanges equal to the quantity of breakers

3
Direct Direct Residual Direct

rotary Motor rotary Motor current rotary Motor
handle operator handle operator device(2) handle operator
PVBX1405 PVBX1404 PVBX1427 PVBX1409
PVCX1405 PVCX1404 PVCX1427 PVCX1409
PVBX2405 PVBX2404 PVBX2427 PVBX2409 PVBX2400 PVBX2412
PVCX2405 PVCX2404 PVCX2427 PVCX2409 PVCX2400 PVCX2412
PVBX2417
PVCX2417
PVBX4405 PVBX4404
PVCX4405 PVCX4404
PVBX4417
PVCX4417

System pro E power

Tmax T vertical installation
To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm. Intermediate uprights
are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary Handle only in non-segregated structures.
Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels. For D=300mm structures, consult the details on page 3/21.

Front or rear (mm) (mm)
circuit- No. Rear No. Residual
breaker No. adjacent circuit-breaker No. adjacent current
connections poli H W CB Fixed Plug-in Withdrawable connections poles H W CB device (1)
T4 3P 4P 350 400 1 PVBT4406 T4 3P 4P 350 400 1
3P 4P 350 600 1 PVCT4406 3P 4P 350 600 1
T5 3P 4P 350 800 2 PVDT5610 4P 450 400 1 PVBT4423
3P 350 1000 4 PVFT5810 4P 450 600 1 PVCT4423
3P 4P 350 1000 3 PVFT5710 T5 3P 4P 350 800 2
400A 3P 4P 350 400 1 PVBT5426 PVBT5414 3P 350 1000 4
3P 4P 350 600 1 PVCT5426 PVCT5414 3P 4P 350 1000 3
3P 4P 350 800 1 PVDT5426 PVDT5414 400A 3P 4P 350 400 1
400A/630A 3P 4P 350 400 1 PVBT5406 3P 4P 350 600 1
3P 4P 350 600 1 PVCT5406
3P 4P 350 800 1
3P 4P 350 800 1 PVDT5406
4P 450 400 1 PVBT5423
630A(1) 3P 450 600 3 PVCT5710
4P 450 600 1 PVCT5423
3P 450 800 4 PVDT5810
4P 450 800 1 PVDT5423
3P 450 600 2 PVCT5601
400A/630A 3P 4P 350 400 1
3P 450 800 3 PVDT5701
3P 4P 350 600 1
3P 450 400 1 PVBT5319
3P 4P 350 800 1
3P 450 600 1 PVCT5307
T6 T6 3P 450 400 1
3P 450 400 1 PVBT6314
3P 4P 400 400 1 PVBT6401 3P 4P 400 400 1
3P 4P 400 600 1 PVCT6401 3P 4P 400 600 1
3P 4P 400 800 1 PVDT6401 3P 4P 400 800 1
3P 4P 450 600 1 PVCT6414 n 3P 4P 450 600 1
3P 4P 450 800 1 PVDT6414 n 3P 4P 450 800 1
3P 4P 450 1000 2 PVFT6610 n 3P 4P 450 1000 2
T7 3P 4P 450 600 1 PVCT7419 T7 3P 4P 450 600 1
3P 4P 450 800 1 PVDT7419 3P 4P 450 800 1
3P 4P 500 600 1 PVCT7413 * 3P 4P 500 600 1
3P 4P 500 800 1 PVDT7413 * 3P 4P 500 800 1
3P 4P 500 1000 2 PVFT7633 * 3P 4P 500 1000 2
(1)
Only front terminals not segregated n
Front terminals, only Form 1 (1)
Compatible residual current devices: RC222 for T4 and T5.
* Only rear terminals

3
Direct Residual Direct Direct

rotary Motor Interlocked current rotary rotary Motor Interlocked
handle operator Interlocked motor-operated device (1) handle handle operator Interlocked motor-operated
PVBT4406 PVBT4404
PVCT4406 PVCT4404
PVDT5612
PVFT5812
PVFT5712
PVBT5426 PVBT5414 PVBT5412
PVCT5426 PVCT5414 PVCT5412
PVDT5426 PVDT5414 PVDT5412
PVBT5428
PVCT5428
PVDT5428
PVBT5406 PVBT5404
PVCT5406 PVCT5404
PVDT5406 PVDT5404
PVBT6314 PVBT6312
PVBT6405 PVBT6404
PVCT6405 PVCT6404
PVDT6405 PVDT6404
PVCT6414 n PVCT6412 n
PVDT6414 n
PVDT6412 n
PVFT6610 PVFT6612 n
PVCT7419 PVCT7419 PVCT7419
PVDT7419 PVDT7419 PVDT7419
PVCT7413 * PVCT7413 * PVCT7413 *
PVDT7413 * PVDT7413 * PVDT7413 *
PVFT7633 *
n

System pro E power
Kits for air circuit-breakers

SACE Emax 2 horizontal / vertical installation
To assemble these kits, order the dedicated intermediate depth upright PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels.

Dimensions (mm) Fixed Withdrawable
Dimensions Interlocked Interlocked
No. Rear circuit-breaker No. (mm)
poles H W Fixed Withdrawable connections poli H W
Front or rear connections, horizontal installation Front or rear connections, horizontal installation
E1.2 3P 4P 400 600 PHCE1241 E1.2 3P 4P 400 600 PHCE1241
3P 4P 400 800 PHDE1241
3P 4P 400 800 PHDE1241
3P 4P 500 600 PHCE1240 *
3P 4P 500 600 PHCE1240
3P 4P 500 800 PHDE1240 *
Front or rear connections, vertical installation 3P 4P 500 800 PHDE1240
E1.2 3P 4P 450 400 PVBE1241 Front or rear connections, vertical installation

3P 4P 450 600 PVCE1241 E1.2 3P 4P 450 400 PVBE1241
3P 4P 450 800 PVDE1241
3P 4P 450 600 PVCE1241
3P 4P 450 800 PVDE1262(1)
3P 4P 500 600 PVCE1240 * 3P 4P 450 800 PVDE1241
3P 4P 500 800 PVDE1240 * 3P 4P 500 600 PVCE1240 *

3P 4P 500 1000 PVFE1263(1) * 3P 4P 500 800 PVDE1240 *
Rear connections, vertical installation Rear connections, vertical installation
E2.2 3P 4P 600 600 PVCE2441 PVCE2450
E2.2 3P 4P 600 600 PVCE2441 PVCE2450
3P 4P 600 800 PVDE2441 PVDE2440
E4.2 3P 4P 600 600 PVCE2442 PVCE4350(2) 3P 4P 600 800 PVDE2441 PVDE2440
3P 4P 600 800 PVDE2441 PVDE2440 E4.2 3P 600 600 PVCE4350
E6.2 3P 700 1000 PVFE6230
3P 4P 600 800 PVDE2441 PVDE2440
E6.2 Neutral 50% 3P/4P 700 1000 PVFE6231
E6.2 3P 700 1000 PVFE6231 PVFE6230
E6.2 Neutral 50/100% 4P 700 1250 PVGE6230
E6.2 Neutral 50/100% 4P 700 1250 PVGE6231 E6.2 50/100% Neutral 4P 700 1250 PVGE6231 PVGE6230
For 3200A busbar systems use structures with D=700mm, for 4000A busbar systems use structures with D=900mm.
(1)
Kit for 2 adjacent circuit-breakers.
(2)
Only 3 poles.
* Only rear terminals.

spaces in between.
RANGE IDENTIFIER
identified by the same initial used for all new components of ABB’s
System pro E power 3
H = Horizontal
V = Vertical
D = DIN-rail
P = Panel
K = Kit
F = Frame
B = 400mm - C = 600mm - D = 800mm - F = 1000mm - G = 1250mm

(Compartment width)
R = Rail
M = System pro M, Mounting
O = OT
P = Panel
F = Flat
B = Blind
X = Tmax XT
T = Tmax T
E = Emax 2
S = Standard, Swing
F = Front, Fixed
H = Horizontal
V = Vertical
R = Recessed
B = Blind
Tmax
For Tmax, the first out of the four digits combined with the last letter,
gives the breakers type. The second digit refers to the number of poles or
side-by-side breakers. The last two digits specify the execution as below
indicated.
3 = 3 Poles / 4 = 4/3-4 Poles / 6 = 2 Breakers / 7 = 3 Breakers / 8 = 4
Breakers / 9 = 5 Breakers
00 = W - RHD / 01 = F / 02 = F - I / 03 = F - I-MO / 04 = F - MO
05 = F - RHD / 06 = F, F - RHD / 07 = P / 09 = P - MO / 10 = W / 11 =
W - I-MO / 12 = W - MO / 13 = W, W - I, W - I-MO, W - MO / 14 = W, W
- RHD / 17 = W - RC / 18 = F - I, F - I-MO / 19 = F, F - I, F - I-MO, F - MO
/ 20 = F, F - RHD, F - MO / 22 = F - I, P - I / 23 = F - RC / 24 = F - I-MO,
P - I-MO / 25 = W - I 26 = P, P - RHD / 27 = P - RHD / 28 = P - RC
29 = F, F - I, F - I-MO, F - MO, F – RHD / 30 = W, W - I, W - I-MO, W -
MO, W – RHD 31 = P - I, P - I-MO / 32 = P - I-MO / 33 = W, W – MO /
36 = W, W – MO / 46 = W / 56 = W - MO
Emax 2
For Emax 2, the first two digits, combined with the last letter, gives the
P H B X 1 4 0 1 breakers type. The last digit specifies the execution as below indicated.
3 = 3 Poli / 4 = 4 Poli, 3-4 Poli / 5 = 3 o 3-4 Poli / 6 = 4 Poli, 3-4 Poli cella
H=600mm
0 = W, W – I / 1 = F, F – I / 2 = F / 3 = W / 6 = W
Key:
F fixed P plug-in W - I withdrawable interlocked
F - I fixed interlocked P - I plug-in interlocked W - I-MO withdrawable interlocked motor-operated
F - I-MO fixed interlocked motor-operated P - I-MO plug-in interlocked motor-operated W - MO withdrawable motor-operated
F - MO fixed motor-operated P - MO plug-in motor-operated W - RC withdrawable with residual current
F - RC fixed with residual current P - RC plug-in with residual current W - RHD withdrawable with direct rotary handle
F - RHD fixed with direct rotary handle P - RHD plug-in with direct rotary handle W&W-I withdrawable and withdrawable interlocked
F & F - I fixed and fixed interlocked W withdrawable

System pro E power
Order codes - Internal kits
Fixed frame for panels

Fixed frame for internal panels; the useful height of the switchboard can be used to full advantage. With fixed frame
for panels, maximum wiring ducts dimension is 80x60mm.
Dimensions
(mm)
Order ABB Package/
Fixed frame for panels 1800 400 PFPF1840 1STQ007449A0000 1/1
3 Fixed frame for panels 1800 600 PFPF1860 1STQ007450A0000 1/1
NEW Special fixed frame for panels

Fixed frame for internal panels; the useful height of the switchboard can be used to full advantage. With fixed
frame for panels, maximum wiring ducts dimension is 80x60mm. The main advantage of the special fixed frame is
to permit the addition of MCCBS kit or Din rail kits without having to remove the entire frame with the front panels
already installed.
Dimensions
(mm)
Order ABB Package/
Special fixed frame for panels 1800 400 PFFA1840 1STQ001889B0000 1/1
1/4
Swing frame for panels and counterdoor application

Swing frame for panels, reduces the available useful space by 100mm. After its opening, it is possible to remo-
ve all the internal panels at once or one by one. In structures without intermediate upright, swing frame PFPS....
cannot be installed with horizontal busbars at all height. In combination with flat blind panel H=1800mm or
H=2000mm operates or counterdoor application.
Dimensions
(mm)
Order ABB Package/
Swing frame for panels 1800 400 PFPS1840 1STQ007459A0000 1/1
PPFB18..
PPFB20.. Swing frame for panels 2000 800 PFPS2080 1STQ007464A0000 1/1

Intermediate upright for internal kit assembly
Intermediate depth upright for assembling kits for Tmax and Emax 2. The intermediate uprights are not required
for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary Handle only in non-
segregated structures. Order 2 uprights for the kits.
PUKI .... Dimensions
(mm)
Order ABB Package/
Description H code code No. pcs
Intermediate upright for internal kits 1800 PUKI1800 1STQ008039A0000 1/1 3
PCCM.... Intermediate upright for internal kits 2000 PUKI2000 1STQ008040A0000 1/1
PCCS....
PUKI ....
PUCM....
PUCS....
Extension kit for D=300mm structures

To be used as an alternative to the intermediate upright in D=300mm structures. The extension kit PKEK0004
cannot be mounted on the first cell at the top or at the bottom of the enclosure, but a minimum H=50mm space
must be left empty from the top or the bottom. It consists of 4 parts that connect the ends of the kit fixing
brackets to the structural rear uprights of D=300mm structures.
Order ABB Package/

Extension kit PKEK0004 1STQ008198A0000 1/1
300 Circuit-breakers and busbars that can be installed in D=300mm structures

B Only use circuit-breakers with front terminals.
Circuit-breaker version XT1 XT2 XT3 XT4 T4 T5 T6 T7 E1.2
Fixed n n n n n n n l l
Fixed with Direct Rotary Handle (RHD) n u n u l l l l
Fixed with motor operator (MO) l l l l l l l l
Fixed interlocked l l l l l l l l l
Fixed interlocked motor-operated l l
Plug-in u l u l l l
A Plug-in with Direct Rotary Handle (RHD) l l l l l l
Plug-in with motor operator (MO) l l l l
Plug-in interlocked l l
Plug-in interlocked motor-operated
Withdrawable l l l l l
Withdrawable with Direct Rotary Handle (RHD) l l l l l
Withdrawable with motor operator (MO) l l
Withdrawable interlocked
Withdrawable interlocked motor-operated
Key
150mm l Circuit-breaker for installation with extension in position B
Maximum encumbrance bars n Circuit-breaker for installation without extension in position A and B
u Circuit-breaker for installation with extension in position A and B

System pro E power
D=300mm structure and cable con- Circuit-breakers and busbars that can be installed in D=300mm structures with
tainer without rear upright
cable container
Only use circuit-breakers with front terminals.
C Circuit-breaker version XT1 XT2 XT3 XT4 T4 T5 T6 T7 E1.2
Fixed n n n n n n n l l
Fixed with Direct Rotary Handle (RHD) n l n l l l l l
Fixed with motor operator (MO) l l l l l l l l
3 D=300mm structure and cable con- Fixed interlocked l l l l l l l l l
tainer without rear upright Fixed interlocked motor-operated l l
Plug-in l l l l l l
Plug-in with Direct Rotary Handle (RHD) l l l l l l
D Plug-in with motor operator (MO) l l l l
Plug-in interlocked l l
Plug-in interlocked motor-operated
Withdrawable l l l l l
Withdrawable with Direct Rotary Handle (RHD) l l l l l
Withdrawable with motor operator (MO) l l
Key
n Circuit-breaker for installation without extension in C structures
l Circuit-breaker for installation with extension in D structures
80x60mm
Kits for DIN rail*

1/4
Description (mm) W code code No. pcs
Standard DIN rail 400 PDRS0400 1STQ008041A0000 1/1
*Cable duct 80x60mm.
N° circuit breakers for each DIN rail

A (mm)
12 mod. 24 mod. 36 mod.
Tmax 210 420 630
XT1 3P 2 5 8
XT1 4P 2 4 6
XT3 3P 2 4 6
XT3 4P 1 3 4

Panels for System Pro-M modular circuit-breakers
Panels with 1/4 turn screws, hinged on the right or the left with the dedicated PHFP0020 kit.
150
=
200
300 Dimensions
(mm)
= Order ABB Package/
Panel with 12 DIN modules 150 400 PPMF1540 1STQ008044A0000 1/1
Panel with 36 DIN modules 150 800 PPMF1580 1STQ008046A0000 1/1 3
Panel with 12x2 DIN modules 300 400 PPMF3040 1STQ008050A0000 1/1
Panels for System Pro-M modular circuit-breakers and Tmax XT1 and Tmax XT3
300 moulded-case circuit-breakers not accessored or with differential module side
RC sel 200 (1)
Panels with 1/4 turn screws, hinged on the right or the left with the dedicated PHFP0020 kit.
Dimensions
(mm)
Order ABB Package/
Panel with 24 DIN modules 300 600 PPMU3060 1STQ008299A0000 1/1
Panel with 36 DIN modules 300 800 PPMU3080 1STQ008300A0000 1/1
The bracket and glossy plate kit can be ordered from the circuit-breaker catalogue. The sole glossy plate is available among the accessories in this
(1)
catalogue.
NEW Panels for Tmax XT1 and Tmax XT3 moulded-case circuit-breakers with
differential module underplace RC (1)
300 Panels with 1/4 turn screws, hinged on the right or the left with the dedicated PHFP0020 kit.
Dimensions
(mm)
Order ABB Package/
Panel with 12 DIN modules 300 400 PPMD3040 1STQ001560B0000 1/1
The bracket and glossy plate kit can be ordered from the circuit-breaker catalogue. The sole glossy plate is available among the accessories in this
(1)
catalogue.

System pro E power
Kits for installation of Tmax circuit-breakers

Horizontal installation (front or rear connections)
The kit includes the dedicated fixing brackets, the mounting plate and panels with 1/4 turn screws, hinged on the
right or the left with the dedicated PHFP0020 kit.
1/4 No. CB
per
No. Dimensions compart- Order ABB Package/No.
Tmax poles Versions H (mm) ment code code pcs
3 12 DIN modules - W=400mm
XT1 3 F - RC 200 1 PHBX1323 1STQ001442B0000 1/1
XT1 3/4 F 150 1 PHBX1401 1STQ007757A0000 1/1
XT1 3/4 F - RHD 150 1 PHBX1405 1STQ007761A0000 1/1
XT1 3/4 F 200 1 PHBX1101 1STQ008473A0000 1/1
XT1 3/4 F - MO 200 1 PHBX1404 1STQ007759A0000 1/1
XT1 3/4 P 200 1 PHBX1407 1STQ007763A0000 1/1
XT1 3/4 P - MO 200 1 PHBX1409 1STQ007765A0000 1/1
XT1 3/4 P - RHD 200 1 PHBX1427 1STQ007767A0000 1/1
XT1 3/4 F - RHD 200 1 PHBX1105 1STQ008475A0000 1/1
XT1 3/4 F-I 500 2 PHBX1422 1STQ008410A0000 1/1
XT1 3/4 F - I-MO 500 2 PHBX1424 1STQ008411A0000 1/1
XT1 3/4 P-I 500 2 PHBX1422 1STQ008410A0000 1/1
XT1 3/4 P - I-MO 500 2 PHBX1424 1STQ008411A0000 1/1
XT1 4 F - RC 200 1 PHBX1423 1STQ007769A0000 1/1
XT2 3 F 150 1 PHBX2301 1STQ007771A0000 1/1
PUKI1800
PUKI2000 XT2 3 W 200 1 PHBX2310 1STQ007787A0000 1/1
PFPF.... XT2 3 W - MO 200 1 PHBX2312 1STQ007789A0000 1/1
PFPS....
CONTINUES
Compatible residual current devices: To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
Tmax XT Intermediate uprights are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with internal panels. For D=300mm structures, consult the details on page 3/21.
residual current device high terminal covers are For fixed and withdrawable 3P breakers Tmax XT, non accessorized and mounted on 3/4P kit, it is necessary to order the dedicated cover
not available. flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on
Tmax T plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked motor-operated kits, it is necessary to order the quantity of
RC222 for T4 and T5. flanges equal to the quantity of breakers.

1/4
No. CB
per
3
12 DIN modules - W=400mm
XT2 3 W - RHD 200 1 PHBX2300 1STQ007791A0000 1/1
XT2 3/4 F 200 1 PHBX2401 1STQ007773A0000 1/1
XT2 3/4 F - MO 200 1 PHBX2404 1STQ007775A0000 1/1
XT2 3/4 F - RHD 200 1 PHBX2405 1STQ007779A0000 1/1
XT2 3/4 P 200 1 PHBX2407 1STQ007781A0000 1/1
XT2 4 P - RC 250 1 PHBX2428 1STQ001450B0000 1/1
XT2 3/4 P - MO 200 1 PHBX2409 1STQ007783A0000 1/1
XT2 3/4 P - RHD 200 1 PHBX2427 1STQ007785A0000 1/1
XT2 3/4 W 250 1 PHBX2410 1STQ007793A0000 1/1
XT2 3/4 W - MO 250 1 PHBX2412 1STQ007795A0000 1/1
XT2 3/4 W - RHD 250 1 PHBX2400 1STQ007799A0000 1/1
XT2 3/4 F-I 500 2 PHBX2402 1STQ008412A0000 1/1
XT2 3/4 F - I-MO 500 2 PHBX2424 1STQ008415A0000 1/1
PUKI1800
PUKI2000 XT2 3/4 P-I 500 2 PHBX2431 1STQ008413A0000 1/1
PFPF.... XT2 3/4 P - I-MO 500 2 PHBX2424 1STQ008415A0000 1/1
PFPS.... XT2 3/4 W-I 500 2 PHBX2425 1STQ008414A0000 1/1
XT2 3/4 W - I-MO 500 2 PHBX2425 1STQ008414A0000 1/1
XT2 4 F - RC 200 1 PHBX2423 1STQ007777A0000 1/1
XT3 3 F 150 1 PHBX3301* 1STQ007801A0000 1/1
XT3 3 F - RHD 150 1 PHBX3305 1STQ007803A0000 1/1
XT3 3/4 F 200 1 PHBX3401* 1STQ007805A0000 1/1
XT3 3/4 F - MO 200 1 PHBX3404 1STQ007807A0000 1/1
Key:
XT3 3/4 F - RHD 200 1 PHBX3405 1STQ007809A0000 1/1
F fixed XT3 3/4 P 200 1 PHBX3407 1STQ007811A0000 1/1
F-I fixed interlocked XT3 3/4 P - MO 200 1 PHBX3409 1STQ007813A0000 1/1
F - I-MO fixed interlocked motor-operated XT3 3/4 P - RHD 200 1 PHBX3427 1STQ007815A0000 1/1
F - MO fixed motor-operated
F - RC fixed with residual current XT3 3/4 F-I 500 2 PHBX3422 1STQ008417A0000 1/1
F - RHD fixed with Direct Rotary Handle XT3 3/4 F - I-MO 500 2 PHBX3424 1STQ008418A0000 1/1
F&F-I fixed and fixed interlocked
P plug-in XT3 3/4 P-I 500 2 PHBX3422 1STQ008417A0000 1/1
P-I plug-in interlocked
XT3 3/4 P - I-MO 500 2 PHBX3424 1STQ008418A0000 1/1
P - I-MO plug-in interlocked motor-
operated XT3 4 F - RC 250 1 PHBX3423* 1STQ007817A0000 1/1
P - MO plug-in motor-operated
P - RC plug-in with residual current
XT4 3 F 150 1 PHBX4301* 1STQ007819A0000 1/1
P - RHD plug-in with Direct Rotary Handle XT4 3/4 F 200 1 PHBX4401* 1STQ007821A0000 1/1
W withdrawable
W-I withdrawable interlocked XT4 3/4 F - MO 200 1 PHBX4404 1STQ007823A0000 1/1
W - I-MO withdrawable interlocked XT4 3/4 F - RHD 200 1 PHBX4405 1STQ007827A0000 1/1
motor-operated
W - MO withdrawable motor-operated XT4 3/4 P 200 1 PHBX4407 1STQ007829A0000 1/1
W - RC withdrawable with residual XT4 4 P - RC 250 1 PHBX4428 1STQ001451B0000 1/1
current
W - RHD withdrawable with Direct Rotary XT4 3/4 P - MO 200 1 PHBX4409 1STQ007831A0000 1/1
Handle
XT4 3/4 P - RHD 200 1 PHBX4427 1STQ007833A0000 1/1
W&W-I withdrawable and withdrawable
interlocked * Not compatible with high terminal covers.
CONTINUE
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC
Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with internal panels. For D=300mm structures, consult the details on page 3/21.
residual current device high terminal covers are For fixed and withdrawable 3P breakers Tmax XT, non accessorized and mounted on 3/4P kit, it is necessary to order the dedicated cover
not available. flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on
Tmax T plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked motor-operated kits, it is necessary to order the quantity of
RC222 for T4 and T5. flanges equal to the quantity of breakers.

System pro E power

1/4 The kit includes the dedicated fixing brackets, the mounting plate and panels with 1/4 turn screws, hinged on the
No. CB
per
3
XT4 3/4 W 250 1 PHBX4410 1STQ007835A0000 1/1
XT4 3/4 W - MO 250 1 PHBX4412 1STQ007837A0000 1/1
XT4 3/4 W - RHD 250 1 PHBX4400 1STQ007841A0000 1/1
XT4 3/4 F-I 500 2 PHBX4402 1STQ008419A0000 1/1
XT4 3/4 F - I-MO 500 2 PHBX4424 1STQ008422A0000 1/1
XT4 3/4 P-I 500 2 PHBX4431 1STQ008420A0000 1/1
XT4 3/4 P - I-MO 500 2 PHBX4424 1STQ008422A0000 1/1
XT4 3/4 W-I 500 2 PHBX4425 1STQ008421A0000 1/1
XT4 3/4 W - I-MO 500 2 PHBX4425 1STQ008421A0000 1/1
XT4 4 F - RC 200 1 PHBX4423 1STQ007825A0000 1/1
T4 3 F 150 1 PHBT4301* 1STQ007843A0000 1/1
PUKI1800
PUKI2000 T4 3/4 F 200 1 PHBT4406* 1STQ007845A0000 1/1
PFPF....
PFPS....
T4 3/4 F - MO 200 1 PHBT4404 1STQ007847A0000 1/1
T4 3/4 F - RHD 200 1 PHBT4406* 1STQ007845A0000 1/1
T4 3/4 F-I 600 2 PHBT4402 1STQ008424A0000 1/1
T5 3 F 400A/630A 200 1 PHBT5306* 1STQ007850A0000 1/1
T5 3 F - MO 400A/630A 200 1 PHBT5304 1STQ007852A0000 1/1
Key: T5 3 F - RHD 400A/630A 200 1 PHBT5306* 1STQ007850A0000 1/1
F fixed
T5 3 P 400A 200 1 PHBT5326 1STQ007854A0000 1/1
F-I fixed interlocked T5 3 P - MO 400A 200 1 PHBT5309 1STQ008406A0000 1/1
F - I-MO fixed interlocked motor-operated
F - MO fixed motor-operated T5 3 P - RHD 400A 200 1 PHBT5326 1STQ007854A0000 1/1
F - RC fixed with residual current
F - RHD fixed with Direct Rotary Handle T5 3 W 400A 300 1 PHBT5314 1STQ007862A0000 1/1
P plug-in T5 3 W - MO 400A 300 1 PHBT5312 1STQ008408A0000 1/1
P - I-MO plug-in interlocked motor- T5 3 W - RHD 400A 300 1 PHBT5314 1STQ007862A0000 1/1
operated
T5 3/4 F 400A/630A 250 1 PHBT5406* 1STQ007856A0000 1/1
T5 3/4 F - MO 400A/630A 250 1 PHBT5404 1STQ007858A0000 1/1
P - RHD plug-in with Direct Rotary Handle
W withdrawable T5 3/4 F - RHD 400A/630A 250 1 PHBT5406* 1STQ007856A0000 1/1
W-I withdrawable interlocked
W - I-MO withdrawable interlocked T5 3/4 P 400A 250 1 PHBT5426 1STQ007860A0000 1/1
motor-operated
W - MO withdrawable motor-operated T5 3/4 P - MO 400A 250 1 PHBT5409 1STQ008407A0000 1/1
W - RC withdrawable with residual
current T5 3/4 P - RHD 400A 250 1 PHBT5426 1STQ007860A0000 1/1
W - RHD withdrawable with Direct Rotary
Handle T5 3/4 W 400A 350 1 PHBT5414 1STQ007864A0000 1/1
interlocked
T5 3/4 W - MO 400A 350 1 PHBT5412 1STQ008409A0000 1/1
T5 3/4 W - RHD 400A 350 1 PHBT5414 1STQ007864A0000 1/1
* Not compatible with high terminal covers. CONTINUES
Compatible residual current devices:
Tmax XT To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC Intermediate uprights are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling
residual current device high terminal covers are internal panels. For D=300mm structures, consult the details on page 3/21.
not available.
For fixed and withdrawable 3P breakers Tmax XT, non accessorized and mounted on 3/4P kit, it is necessary to order the dedicated cover
Tmax T flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on
RC222 for T4 and T5. plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked motor-operated kits, it is necessary to order the quantity of
flanges equal to the quantity of breakers.

No. CB
per
Tmax poles Version H (mm) ment code code pcs 3
24 moduli DIN - L=600mm
XT1 3/4 F 200 1 PHCX1101 1STQ008474A0000 1/1
XT1 3 F - RC 200 1 PHCX1323 1STQ001443B0000 1/1
XT1 3/4 F 150 1 PHCX1401 1STQ007758A0000 1/1
XT1 3/4 F - RHD 150 1 PHCX1405 1STQ007762A0000 1/1
XT1 3/4 F - RHD 200 1 PHCX1105 1STQ008476A0000 1/1
XT1 3/4 F - MO 200 1 PHCX1404 1STQ007760A0000 1/1
XT1 3/4 P 200 1 PHCX1407 1STQ007764A0000 1/1
XT1 3/4 P - MO 200 1 PHCX1409 1STQ007766A0000 1/1
XT1 3/4 P - RHD 200 1 PHCX1427 1STQ007768A0000 1/1
XT1 3/4 F-I 500 2 PHCX1422 1STQ008432A0000 1/1
XT1 3/4 F - I-MO 500 2 PHCX1424 1STQ008433A0000 1/1
XT1 3/4 P-I 500 2 PHCX1422 1STQ008432A0000 1/1
PUKI1800 XT1 3/4 P - I-MO 500 2 PHCX1424 1STQ008433A0000 1/1
PUKI2000 XT1 4 F - RC 200 1 PHCX1423 1STQ007770A0000 1/1
PFPF....
XT2 3 F 150 1 PHCX2301 1STQ007772A0000 1/1
PFPS....
XT2 3 W 200 1 PHCX2310 1STQ007788A0000 1/1
XT2 3 W - MO 200 1 PHCX2312 1STQ007790A0000 1/1
XT2 3 W - RHD 200 1 PHCX2300 1STQ007792A0000 1/1
XT2 3/4 F 200 1 PHCX2401 1STQ007774A0000 1/1
XT2 3/4 F - MO 200 1 PHCX2404 1STQ007776A0000 1/1
XT2 3/4 F - RHD 200 1 PHCX2405 1STQ007780A0000 1/1
XT2 3/4 P 200 1 PHCX2407 1STQ007782A0000 1/1
XT2 3/4 P - MO 200 1 PHCX2409 1STQ007784A0000 1/1
XT2 3/4 P - RHD 200 1 PHCX2427 1STQ007786A0000 1/1
XT2 3/4 W 250 1 PHCX2410 1STQ007794A0000 1/1
XT2 3/4 W - MO 250 1 PHCX2412 1STQ007796A0000 1/1
XT2 3/4 W - RHD 250 1 PHCX2400 1STQ007800A0000 1/1
XT2 3/4 F-I 500 2 PHCX2402 1STQ008434A0000 1/1
XT2 3/4 F - I-MO 500 2 PHCX2424 1STQ008437A0000 1/1
XT2 3/4 P-I 500 2 PHCX2431 1STQ008435A0000 1/1
XT2 3/4 P - I-MO 500 2 PHCX2424 1STQ008437A0000 1/1
XT2 3/4 W-I 500 2 PHCX2425 1STQ008436A0000 1/1
XT2 3/4 W - I-MO 500 2 PHCX2425 1STQ008436A0000 1/1
XT2 4 F - RC 200 1 PHCX2423 1STQ007778A0000 1/1
XT2 4 W - RC 250 1 PHCX2417 1STQ007798A0000 1/1
XT3 3 F 150 1 PHCX3301 1STQ007802A0000 1/1
XT3 3 F - RHD 150 1 PHCX3305 1STQ007804A0000 1/1
XT3 3/4 F 200 1 PHCX3401 1STQ007806A0000 1/1
XT3 3/4 F - MO 200 1 PHCX3404 1STQ007808A0000 1/1
Compatible residual current devices: CONTINUES

Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling
residual current device high terminal covers are internal panels. For D=300mm structures, consult the details on page 3/21.
not available.
Tmax T flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on
RC222 for T4 and T5. plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked motor-operated kits, it is necessary to order the quantity of

System pro E power

No. CB
Dimen- per
No. sions compart- Order ABB Package/No.
3 Tmax poles Version H (mm) ment code code pcs
XT3 3/4 F - RHD 200 1 PHCX3405 1STQ007810A0000 1/1
XT3 3/4 P 200 1 PHCX3407 1STQ007812A0000 1/1
XT3 3/4 P - MO 200 1 PHCX3409 1STQ007814A0000 1/1
XT3 3/4 P - RHD 200 1 PHCX3427 1STQ007816A0000 1/1
XT3 3/4 F - I 500 2 PHCX3422 1STQ008439A0000 1/1
XT3 3/4 F - I-MO 500 2 PHCX3424 1STQ008440A0000 1/1
XT3 3/4 P - I 500 2 PHCX3422 1STQ008439A0000 1/1
XT3 3/4 P - I-MO 500 2 PHCX3424 1STQ008440A0000 1/1
XT3 4 F - RC 250 1 PHCX3423 1STQ007818A0000 1/1
XT4 3 F 150 1 PHCX4301 1STQ007820A0000 1/1
XT4 3/4 F 200 1 PHCX4401 1STQ007822A0000 1/1
XT4 3/4 F - MO 200 1 PHCX4404 1STQ007824A0000 1/1
XT4 3/4 F - RHD 200 1 PHCX4405 1STQ007828A0000 1/1
PUKI1800
PUKI2000
XT4 3/4 P 200 1 PHCX4407 1STQ007830A0000 1/1
PFPF.... XT4 3/4 P - MO 200 1 PHCX4409 1STQ007832A0000 1/1
PFPS.... XT4 3/4 P - RHD 200 1 PHCX4427 1STQ007834A0000 1/1
XT4 3/4 W 250 1 PHCX4410 1STQ007836A0000 1/1
XT4 3/4 W - MO 250 1 PHCX4412 1STQ007838A0000 1/1
XT4 3/4 W - RHD 250 1 PHCX4400 1STQ007842A0000 1/1
XT4 3/4 F - I 500 2 PHCX4402 1STQ008441A0000 1/1
XT4 3/4 F - I-MO 500 2 PHCX4424 1STQ008444A0000 1/1
XT4 3/4 P - I 500 2 PHCX4431 1STQ008442A0000 1/1
XT4 3/4 P - I-MO 500 2 PHCX4424 1STQ008444A0000 1/1
Key: XT4 3/4 W - I 500 2 PHCX4425 1STQ008443A0000 1/1
F fixed XT4 3/4 W - I-MO 500 2 PHCX4425 1STQ008443A0000 1/1
F-I fixed interlocked XT4 4 F - RC 200 1 PHCX4423 1STQ007826A0000 1/1
F - MO fixed motor-operated XT4 4 W - RC 250 1 PHCX4417 1STQ007840A0000 1/1
F - RC fixed with residual current T4 3 F 150 1 PHCT4301 1STQ007844A0000 1/1
F - RHD fixed with Direct Rotary Handle
T4 3/4 F 200 1 PHCT4406 1STQ007846A0000 1/1
P plug-in T4 3/4 F - MO 200 1 PHCT4404 1STQ007848A0000 1/1
T4 3/4 F - RHD 200 1 PHCT4406 1STQ007846A0000 1/1
operated T4 3/4 F - I 600 2 PHCT4402 1STQ008446A0000 1/1
T4 3/4 F - I-MO 600 2 PHCT4403 1STQ008447A0000 1/1
P - RHD plug-in with Direct Rotary Handle T4 4 F - RC 200 1 PHCT4423 1STQ007849A0000 1/1
W withdrawable
T5 3 F 400A/630A 200 1 PHCT5306 1STQ007851A0000 1/1
W - I-MO withdrawable interlocked T5 3 F - MO 400A/630A 200 1 PHCT5304 1STQ007853A0000 1/1
motor-operated T5 3 F - RHD 400A/630A 200 1 PHCT5306 1STQ007851A0000 1/1
W - MO withdrawable motor-operated
W - RC withdrawable with residual T5 3 P 400A 200 1 PHCT5326 1STQ007855A0000 1/1
current
T5 NEW 3/4 P 630A 250 1 PHCT5407 1STQ002113A0000 1/1
Handle T5 3 P - MO 400A 200 1 PHCT5309 1STQ008428A0000 1/1
W&W-I withdrawable and withdrawable T5 3 P - RHD 400A 200 1 PHCT5326 1STQ007855A0000 1/1
interlocked
T5 3 W 400A 300 1 PHCT5314 1STQ007863A0000 1/1
T5 3 W - MO 400A 300 1 PHCT5312 1STQ008430A0000 1/1
Compatible residual current devices: T5 NEW 3/4 W - MO 630A 250 1 PHCT5427 1STQ002114A0000 1/1
Tmax XT CONTINUES
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with Intermediate uprights are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary
residual current device high terminal covers are Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal
not available.
panels. For D=300mm structures, consult the details on page 3/21. For fixed and withdrawable 3P breakers Tmax XT, non accessorized and
Tmax T mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2
RC222 for T4 and T5. 3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked
motor-operated kits, it is necessary to order the quantity of flanges equal to the quantity of breakers.

No. CB
per
Tmax poles Version H (mm) ment code code pcs
3
T5 3 W - RHD 400A 300 1 PHCT5314 1STQ007863A0000 1/1
T5 3/4 F 400A/630A 250 1 PHCT5406 1STQ007857A0000 1/1
T5 3/4 F - MO 400A/630A 250 1 PHCT5404 1STQ007859A0000 1/1
T5 3/4 F - RHD 400A/630A 250 1 PHCT5406 1STQ007857A0000 1/1
T5 3/4 P 400A 250 1 PHCT5426 1STQ007861A0000 1/1
T5 3/4 P - MO 400A 250 1 PHCT5409 1STQ008429A0000 1/1
T5 3/4 P - RHD 400A 250 1 PHCT5426 1STQ007861A0000 1/1
T5 3/4 W 400A 350 1 PHCT5414 1STQ007865A0000 1/1
T5 3/4 W - MO 400A 350 1 PHCT5412 1STQ008431A0000 1/1
T5 3/4 W - RHD 400A 350 1 PHCT5414 1STQ007865A0000 1/1
T5 3/4 F - I 400A/630A 600 2 PHCT5402 1STQ007868A0000 1/1
T5 3/4 F - I-MO 400A/630A 600 2 PHCT5403 1STQ008448A0000 1/1
T5 3/4 P - I 400A 600 2 PHCT5431 1STQ008449A0000 1/1
T5 3/4 P - I-MO 400A 600 2 PHCT5432 1STQ008450A0000 1/1
T5 3/4 W - I 400A 600 2 PHCT5425 1STQ008451A0000 1/1
PUKI1800 T5 3/4 W - I-MO 400A 600 2 PHCT5411 1STQ008452A0000 1/1
PUKI2000 T5 3/4 F - I 400A/630A 600 2 PHCT5402 1STQ007868A0000 1/1
PFPF....
PFPS....
T5 4 F - RC 250 1 PHCT5423 1STQ007866A0000 1/1
T6 3 F 300 1 PHCT6301** 1STQ007877A0000 1/1
T6 3 F - MO 300 1 PHCT6304** 1STQ007879A0000 1/1
T6 3 F - RHD 300 1 PHCT6305** 1STQ007881A0000 1/1
T6 3 W 350 1 PHCT6314 n 1STQ007891A0000 1/1
T6 3 W - MO 350 1 PHCT6312 n 1STQ007889A0000 1/1
T6 3 W - RHD 350 1 PHCT6314 n 1STQ007891A0000 1/1
T6 3/4 F 350 1 PHCT6401** 1STQ007883A0000 1/1
T6 3/4 F - MO 350 1 PHCT6404 1STQ007885A0000 1/1
T6 3/4 F - RHD 350 1 PHCT6405 1STQ007887A0000 1/1
Key:
T6 3/4 W 500 1 PHCT6410 n 1STQ007893A0000 1/1
F fixed T6 3/4 W - MO 500 1 PHCT6412 n 1STQ007894A0000 1/1
F-I fixed interlocked T6 3/4 W - RHD 500 1 PHCT6410 n 1STQ007896A0000 1/1
F - MO fixed motor-operated T6 3/4 F - I 700 2 PHCT6402 1STQ008453A0000 1/1
F - RC fixed with residual current T6 3/4 F - I-MO 700 2 PHCT6403 1STQ008454A0000 1/1
F - RHD fixed with Direct Rotary Handle T6 3/4 W - I 700 2 PHCT6425 n 1STQ008455A0000 1/1
P plug-in T6 3/4 W - I-MO 700 2 PHCT6411 n 1STQ008456A0000 1/1
P-I plug-in interlocked T7 3 F 300 1 PHCT7329 1STQ007898A0000 1/1
P - I-MO plug-in interlocked motor- T7 3 F-I 300 1 PHCT7329 1STQ007898A0000 1/1
operated
T7 3 F - I-MO 300 1 PHCT7329 1STQ007898A0000 1/1
P - RC plug-in with residual current T7 3 F - MO 300 1 PHCT7329 1STQ007898A0000 1/1
P - RHD plug-in with Direct Rotary Handle T7 3 F - RHD 300 1 PHCT7329 1STQ007898A0000 1/1
W withdrawable
T7 3/4 F 350 1 PHCT7420 1STQ007899A0000 1/1
W - I-MO withdrawable interlocked T7 3/4 F - MO 350 1 PHCT7420 1STQ007899A0000 1/1
motor-operated T7 3/4 F - RHD 350 1 PHCT7420 1STQ007899A0000 1/1
W - MO withdrawable motor-operated T7 3/4 F - I 400 1 PHCT7418 1STQ007900A0000 1/1
current T7 3/4 F - I-MO 400 1 PHCT7418 1STQ007900A0000 1/1
W - RHD withdrawable with Direct Rotary T7 3/4 W 500 1 PHCT7430 * 1STQ007902A0000 1/1
Handle T7 3/4 W - I 500 1 PHCT7430 * 1STQ007902A0000 1/1
interlocked
T7 3/4 W - I-MO 500 1 PHCT7430 * 1STQ007902A0000 1/1
T7 3/4 W - MO 500 1 PHCT7430 * 1STQ007902A0000 1/1
T7 3/4 W - RHD 500 1 PHCT7430 * 1STQ007902A0000 1/1
Compatible residual current devices: n
Front terminals, only Form 1 ** T6 1000A front terminals in width 800mm. CONTINUES
Tmax XT * Only rear terminals
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with Intermediate uprights are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary
residual current device high terminal covers are Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal
not available.
panels. For D=300mm structures, consult the details on page 3/21. For fixed and withdrawable 3P breakers Tmax XT, non accessorized and
Tmax T mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2
RC222 for T4 and T5. 3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked

System pro E power

No. CB
Dimen- per
No. sions compart- Order ABB Package/No.
3
XT1 NEW 3/4 F 150 1 PHDX1301 1STQ002098B0000 1/1
XT1 NEW 3/4 F 200 1 PHDX1401 1STQ002097B0000 1/1
XT1 4 F - RC 200 1 PHDX1423 1STQ001472B0000 1/1
XT2 3/4 F 200 1 PHDX2401 1STQ001444B0000 1/1
XT2 NEW 3/4 P 200 1 PHDX2407 1STQ002099B0000 1/1
XT2 3/4 F - MO 200 1 PHDX2404 1STQ001445B0000 1/1
XT2 4 F - RC 200 1 PHDX2423 1STQ001446B0000 1/1
XT2 4 P - RC 250 1 PHDX2428 1STQ001464B0000 1/1
XT3 NEW 3/4 F 200 1 PHDX3401 1STQ002101B0000 1/1
XT3 4 F - RC 200 1 PHDX3423 1STQ001473B0000 1/1
XT3 NEW 3/4 P 200 1 PHDX3407 1STQ002106B0000 1/1
XT4 3/4 F 200 1 PHDX4401 1STQ001447B0000 1/1
XT4 NEW 3/4 F - RHD 200 1 PHDX4405 1STQ002131B0000 1/1
XT4 3/4 F - MO 200 1 PHDX4404 1STQ001448B0000 1/1
PUKI1800 XT4 4 F - RC 200 1 PHDX4423 1STQ001449B0000 1/1
PUKI2000 XT4 NEW 3/4 P 200 1 PHDX4407 1STQ002110B0000 1/1
PFPF.... XT4 4 P - RC 250 1 PHDX4428 1STQ001451B0000 1/1
PFPS.... T4 3/4 F - I 600 2 PHDT4402 1STQ008463A0000 1/1
T4 3/4 F - I-MO 600 2 PHDT4403 1STQ008464A0000 1/1
T5 3 F 400A/630A 200 1 PHDT5306 1STQ007869A0000 1/1
T5 3 F - MO 400A/630A 200 1 PHDT5304 1STQ007870A0000 1/1
T5 3 F - RHD 400A/630A 200 1 PHDT5306 1STQ007869A0000 1/1
T5 3P P - MO 400A 200 1 PHDT5309 1STQ008457A0000 1/1
T5 3 P 400A 200 1 PHDT5326 1STQ007871A0000 1/1
T5 3P P - MO 400A 200 1 PHDT5309 1STQ008457A0000 1/1
T5 3 P - RHD 400A 200 1 PHDT5326 1STQ007871A0000 1/1
Key: T5 3 W 400A 300 1 PHDT5314 1STQ007875A0000 1/1
F fixed T5 3P W - MO 400A 300 1 PHDT5312 1STQ008459A0000 1/1
F-I fixed interlocked T5 3 W - RHD 400A 300 1 PHDT5314 1STQ007875A0000 1/1
F - I-MO fixed interlocked motor-operated T5 3/4 F 400A/630A 250 1 PHDT5406 1STQ007872A0000 1/1
T5 3/4 F - MO 400A/630A 250 1 PHDT5404 1STQ007873A0000 1/1
F - RHD fixed with Direct Rotary Handle T5 3/4 F - RHD 400A/630A 250 1 PHDT5406 1STQ007872A0000 1/1
F&F-I fixed and fixed interlocked T5 3/4 P 400A 250 1 PHDT5426 1STQ007874A0000 1/1
P plug-in T5 3/4 P - MO 400A 250 1 PHDT5409 1STQ008458A0000 1/1
P - I-MO plug-in interlocked motor- T5 3/4 P - RHD 400A 250 1 PHDT5426 1STQ007874A0000 1/1
operated T5 3/4 W 400A 350 1 PHDT5414 1STQ007876A0000 1/1
P - MO plug-in motor-operated T5 3/4 W - MO 400A 350 1 PHDT5412 1STQ008460A0000 1/1
P - RHD plug-in with Direct Rotary Handle T5 3/4 W - RHD 400A 350 1 PHDT5414 1STQ007876A0000 1/1
W withdrawable T5 3/4 W - I 400A 600 1 PHDT5425 1STQ008461A0000 1/1
W-I withdrawable interlocked T5 3/4 W - I - MO 400A 600 1 PHDT5411 1STQ008462A0000 1/1
W - I-MO withdrawable interlocked
motor-operated
T5 4 F - RC 400A 250 1 PHDT5423 1STQ007867A0000 1/1
W - MO withdrawable motor-operated T5 4 F - RC 250 1 PHDT5423 1STQ007867A0000 1/1
W - RC withdrawable with residual T6 3 F 300 1 PHDT6301 1STQ007878A0000 1/1
current T6 3 F - MO 300 1 PHDT6304 1STQ007880A0000 1/1
Handle T6 3 F - RHD 300 1 PHDT6305 1STQ007882A0000 1/1
W&W-I withdrawable and withdrawable T6 3 W 350 1 PHDT6314 n 1STQ007892A0000 1/1
interlocked T6 3 W - MO 350 1 PHDT6312 n 1STQ007890A0000 1/1
T6 3 W - RHD 350 1 PHDT6314 n 1STQ007892A0000 1/1
Compatible residual current devices: T6 3/4 F 350 1 PHDT6401 1STQ007884A0000 1/1
Tmax XT T6 3/4 F - MO 350 1 PHDT6404 1STQ007886A0000 1/1
n
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC Front terminals, only Form 1 CONTINUES
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with
residual current device high terminal covers are
To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
not available. Intermediate uprights are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary
Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal
Tmax T
panels. For D=300mm structures, consult the details on page 3/21.For fixed and withdrawable 3P breakers Tmax XT, non accessorized and
RC222 for T4 and T5.
mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2
3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked

Key: Kits for installation of Tmax circuit-breakers
F fixed Horizontal installation (front or rear connections)
F-I fixed interlocked
F - I-MO fixed interlocked motor-operated The kit includes the dedicated fixing brackets, the mounting plate and panels with 1/4 turn screws, hinged on the
F&F-I fixed and fixed interlocked No. CB
P plug-in per
P-I plug-in interlocked No. Dimensions compart- Order ABB Package/No.
P - I-MO plug-in interlocked motor- Tmax poles Version H (mm) ment code code pcs
operated 3
P - MO plug-in motor-operated 36 DIN modules - W=800mm
P - RHD plug-in with Direct Rotary Handle T6 3/4 F - RHD 350 1 PHDT6405 1STQ007888A0000 1/1
W withdrawable T6 3/4 W 500 1 PHDT6414 n 1STQ007897A0000 1/1
W - I-MO withdrawable interlocked T6 3/4 W - MO 500 1 PHDT6412 n 1STQ007895A0000 1/1
motor-operated T6 3/4 W - RHD 500 1 PHDT6414 n 1STQ007897A0000 1/1
W - RC withdrawable with residual T7 3 F 300 1 PHDT7329 1STQ007903A0000 1/1
current
T7 3 F-I 300 1 PHDT7329 1STQ007903A0000 1/1
Handle T7 3 F - I-MO 300 1 PHDT7329 1STQ007903A0000 1/1
interlocked
T7 3 F - MO 300 1 PHDT7329 1STQ007903A0000 1/1
T7 3 F - RHD 300 1 PHDT7329 1STQ007903A0000 1/1
Compatible residual current devices: T7 3/4 F 350 1 PHDT7420 1STQ007904A0000 1/1
Tmax XT T7 3/4 F - MO 350 1 PHDT7420 1STQ007904A0000 1/1
RC Inst. XT1-XT3, RC Sel. XT1-XT3 and RC T7 3/4 F - RHD 350 1 PHDT7420 1STQ007904A0000 1/1
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with T7 3/4 F-I 400 1 PHDT7418 1STQ007905A0000 1/1
residual current device high terminal covers are
not available. T7 3/4 F - I-MO 400 1 PHDT7418 1STQ007905A0000 1/1
Tmax T T7 3/4 W 500 1 PHDT7430 * 1STQ007907A0000 1/1
RC222 for T4 and T5. T7 3/4 W-I 500 1 PHDT7430 * 1STQ007907A0000 1/1
T7 3/4 W - I-MO 500 1 PHDT7430 * 1STQ007907A0000 1/1
T7 3/4 W - MO 500 1 PHDT7430 * 1STQ007907A0000 1/1
T7 3/4 W - RHD 500 1 PHDT7430 * 1STQ007907A0000 1/1
n
Intermediate uprights are not required for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary
Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling
1/4 internal panels. For D=300mm structures, consult the details on page 3/21.
flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2 3P mounted on plate, AD3307 flange for XT3 3P mounted on
plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked motor-operated kits, it is necessary to order the quantity of
Kits for installation of Emax 2 circuit-breakers

No. Dimensions No. CB per Order ABB Package/No.
Emax poles Version H (mm) compartment code code pcs
E1.2 3/4 F 400 1 PHCE1241 1STQ008151A0000 1/1
E1.2 3/4 F-I 400 1 PHCE1241 1STQ008151A0000 1/1
E1.2 3/4 W 500 1 PHCE1240 * 1STQ008164A0000 1/1
E1.2 3/4 W-I 500 1 PHCE1240 * 1STQ008164A0000 1/1
PUKI1800 E1.2 3/4 F 400 1 PHDE1241 1STQ008150A0000 1/1
PUKI2000 PFPF.... E1.2 3/4 F-I 400 1 PHDE1241 1STQ008150A0000 1/1
PFPS.... E1.2 3/4 W 500 1 PHDE1240 * 1STQ008386A0000 1/1
Key: E1.2 3/4 W-I 500 1 PHDE1240 * 1STQ008386A0000 1/1
F fixed
W withdrawable
W-I withdrawable interlocked Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels.

System pro E power

Vertical installation (front or rear connections)
No. CB
per
3
XT1 3/4 F 300 1 PVBX1401 1STQ007908A0000 1/1
XT1 3/4 F - MO 300 1 PVBX1404 1STQ008465A0000 1/1
XT1 3/4 F - RHD 300 1 PVBX1405 1STQ007912A0000 1/1
XT1 3/4 P 300 1 PVBX1407 1STQ007914A0000 1/1
XT1 3/4 P - MO 300 1 PVBX1409 1STQ007916A0000 1/1
XT1 3/4 P - RHD 300 1 PVBX1427 1STQ007918A0000 1/1
XT1 4 F - RC 300 1 PVBX1423 1STQ007910A0000 1/1
XT1 3/4 F - MO 300 1 PVBX1404 1STQ008465A0000 1/1
XT2 3/4 F - MO 300 1 PVBX2404 1STQ008466A0000 1/1
XT2 3/4 F 300 1 PVBX2401 1STQ007921A0000 1/1
XT2 3/4 F - RHD 300 1 PVBX2405 1STQ007925A0000 1/1
XT2 3/4 P 300 1 PVBX2407 1STQ007927A0000 1/1
XT2 3/4 P - MO 300 1 PVBX2409 1STQ007931A0000 1/1
PUKI1800
PUKI2000 XT2 3/4 P - RHD 300 1 PVBX2427 1STQ007933A0000 1/1
PFPF.... XT2 3/4 W 300 1 PVBX2410 1STQ007935A0000 1/1
PFPS....
XT2 3/4 W - MO 300 1 PVBX2412 1STQ007937A0000 1/1
XT2 3/4 W - RHD 300 1 PVBX2400 1STQ007939A0000 1/1
XT2 4 F - RC 350 1 PVBX2423 1STQ007941A0000 1/1
XT2 4 W - RC 350 1 PVBX2417 1STQ007943A0000 1/1
XT3 3/4 F 300 1 PVBX3401 1STQ007945A0000 1/1
XT3 3/4 F - MO 300 1 PVBX3404 1STQ008467A0000 1/1
XT3 3/4 F - RHD 300 1 PVBX3405 1STQ007947A0000 1/1
XT3 3/4 P 300 1 PVBX3407 1STQ007949A0000 1/1
XT3 3/4 P - MO 300 1 PVBX3409 1STQ007952A0000 1/1
Key: XT3 3/4 P - RHD 300 1 PVBX3427 1STQ007954A0000 1/1
F fixed XT3 4 F - RC 400 1 PVBX3423 1STQ007956A0000 1/1
F - I-MO fixed interlocked motor-operated XT4 3/4 F 300 1 PVBX4401 1STQ007960A0000 1/1
F - MO fixed motor-operated XT4 3/4 F - MO 300 1 PVBX4404 1STQ008468A0000 1/1
F - RHD fixed with Direct Rotary Handle XT4 3/4 F - RHD 300 1 PVBX4405 1STQ007964A0000 1/1
F&F-I fixed and fixed interlocked XT4 3/4 P 350 1 PVBX4407 1STQ007966A0000 1/1
P plug-in
P-I plug-in interlocked XT4 3/4 P - MO 350 1 PVBX4409 1STQ007970A0000 1/1
XT4 3/4 P - RHD 350 1 PVBX4427 1STQ007972A0000 1/1
operated
P - MO plug-in motor-operated XT4 3/4 W 350 1 PVBX4410 1STQ007974A0000 1/1
XT4 3/4 W - MO 350 1 PVBX4412 1STQ007976A0000 1/1
W withdrawable XT4 3/4 W - RHD 350 1 PVBX4400 1STQ007978A0000 1/1
W - I-MO withdrawable interlocked XT4 4 F - RC 400 1 PVBX4423 1STQ007958A0000 1/1
motor-operated XT4 4 W - RC 400 1 PVBX4417 1STQ007980A0000 1/1
W - RC withdrawable with residual T4 3/4 F 350 1 PVBT4406 1STQ007982A0000 1/1
current T4 3/4 F - MO 350 1 PVBT4404 1STQ007984A0000 1/1
Handle T4 3/4 F - RHD 350 1 PVBT4406 1STQ007982A0000 1/1
interlocked
T4 4 F - RC 450 1 PVBT4423 1STQ007986A0000 1/1
CONTINUES
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with panels. For D=300mm structures, consult the details on page 3/21. For fixed and withdrawable 3P breakers Tmax XT, non accessorized and
residual current device high terminal covers are mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2
not available. 3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked
Tmax T motor-operated kits, it is necessary to order the quantity of flanges equal to the quantity of breakers.

1/4
No. CB
per
3
T5 3/4 F 400A/630A 350 1 PVBT5406 1STQ007988A0000 1/1
T5 3/4 F - MO 400A/630A 350 1 PVBT5404 1STQ007990A0000 1/1
T5 3/4 F - RHD 400A/630A 350 1 PVBT5406 1STQ007988A0000 1/1
T5 3/4 P 400A 350 1 PVBT5426 1STQ007992A0000 1/1
T5 3/4 P - RHD 400A 350 1 PVBT5426 1STQ007992A0000 1/1
T5 3/4 W 400A 350 1 PVBT5414 1STQ007993A0000 1/1
T5 3/4 W - MO 400A 350 1 PVBT5412 1STQ007995A0000 1/1
T5 3/4 W - RHD 400A 350 1 PVBT5414 1STQ007993A0000 1/1
T5 4 F - RC 400A 450 1 PVBT5423 1STQ007998A0000 1/1
T5 4 P - RC 400A 450 1 PVBT5428 1STQ008001A0000 1/1
T5 3 W 630A 450 1 PVBT5319 n 1STQ001470B0000 1/1
T6 3 W 450 1 PVBT6314 n 1STQ008024A0000 1/1
T6 3 W - MO 450 1 PVBT6312 n 1STQ008025A0000 1/1
T6 3 W - RHD 450 1 PVBT6314 n 1STQ008024A0000 1/1
PUKI1800
T6 3/4 F 400 1 PVBT6401 1STQ008015A0000 1/1
PUKI2000
PFPF.... T6 3/4 F - MO 400 1 PVBT6404 1STQ008018A0000 1/1
PFPS.... T6 3/4 F - RHD 400 1 PVBT6405 1STQ008021A0000 1/1
XT1 3/4 F 300 1 PVCX1401 1STQ007909A0000 1/1
XT1 NEW 3 F 300 4 PVCX1301 1STQ001885B0000 1/1
XT1 3/4 F - MO 300 1 PVCX1404 1STQ008469A0000 1/1
XT1 3/4 F - RHD 300 1 PVCX1405 1STQ007913A0000 1/1
XT1 3/4 P 300 1 PVCX1407 1STQ007915A0000 1/1
XT1 3/4 P 300 3 PVCX1707 1STQ009146A0000 1/1
XT1 3/4 P - MO 300 1 PVCX1409 1STQ007917A0000 1/1
XT1 3/4 P - RHD 300 1 PVCX1427 1STQ007919A0000 1/1
XT1 4 F - RC 300 1 PVCX1423 1STQ007911A0000 1/1
Key: XT2 3/4 F 300 3 PVCX2701 1STQ007923A0000 1/1
F fixed XT2 3/4 F 300 1 PVCX2401 1STQ007922A0000 1/1
F-I fixed interlocked XT2 3/4 F - MO 300 1 PVCX2404 1STQ008470A0000 1/1
XT2 3/4 F - RHD 300 1 PVCX2405 1STQ007926A0000 1/1
F - RC fixed with residual current XT2 3/4 P 300 3 PVCX2707 1STQ007929A0000 1/1
XT2 3/4 P 300 1 PVCX2407 1STQ007928A0000 1/1
P plug-in XT2 3/4 P - MO 300 1 PVCX2409 1STQ007932A0000 1/1
P-I plug-in interlocked XT2 3/4 P - RHD 300 1 PVCX2427 1STQ007934A0000 1/1
operated XT2 3/4 W 300 1 PVCX2410 1STQ007936A0000 1/1
P - MO plug-in motor-operated XT2 3/4 W - MO 300 1 PVCX2412 1STQ007938A0000 1/1
XT2 3/4 W - RHD 300 1 PVCX2400 1STQ007940A0000 1/1
W withdrawable XT2 4 F - RC 350 1 PVCX2423 1STQ007942A0000 1/1
W-I withdrawable interlocked XT2 4 W - RC 350 1 PVCX2417 1STQ007944A0000 1/1
motor-operated XT3 3 P 300 3 PVCX3707 1STQ009149A0000 1/1
W - MO withdrawable motor-operated XT3 3/4 F 300 1 PVCX3401 1STQ007946A0000 1/1
current XT3 NEW 3 F 300 3 PVCX3301 1STQ001886B0000 1/1
W - RHD withdrawable with Direct Rotary XT3 3/4 F - MO 300 1 PVCX3404 1STQ008471A0000 1/1
Handle
XT3 3/4 F - RHD 300 1 PVCX3405 1STQ007948A0000 1/1
interlocked XT3 3/4 P 300 1 PVCX3407 1STQ007950A0000 1/1
XT3 3/4 P 300 2 PVCX3607 1STQ009148A0000 1/1
Compatible residual current devices: n
Front terminals, only Form 1 CONTINUES
Sel.. XT2-XT4 Type A. For XT1-XT3 fixed with Handle only in non-segregated structures. Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal
residual current device high terminal covers are panels. For D=300mm structures, consult the details on page 3/21. For fixed and withdrawable 3P breakers Tmax XT, non accessorized and
not available.
mounted on 3/4P kit, it is necessary to order the dedicated cover flanges: AD3305 flange for XT1 3P mounted on plate, AD3306 flange for XT2
Tmax T 3P mounted on plate, AD3307 flange for XT3 3P mounted on plate, AD3308 flange for XT4 3P mounted on plate. With interlocked or interlocked
RC222 for T4 and T5. motor-operated kits, it is necessary to order the quantity of flanges equal to the quantity of breakers.

System pro E power

No. CB
per
3 24 DIN modules - W=600mm
XT3 3/4 P - MO 300 1 PVCX3409 1STQ007953A0000 1/1
XT3 3/4 P - RHD 300 1 PVCX3427 1STQ007955A0000 1/1
XT3 4 F - RC 400 1 PVCX3423 1STQ007957A0000 1/1
XT4 3/4 F 300 1 PVCX4401 1STQ007961A0000 1/1
XT4 3/4 F 300 2 PVCX4601 1STQ009142A0000 1/1
XT4 3 F 300 3 PVCX4701 1STQ007962A0000 1/1
XT4 3/4 F - MO 300 1 PVCX4404 1STQ008472A0000 1/1
XT4 3/4 F - RHD 300 1 PVCX4405 1STQ007965A0000 1/1
XT4 3 P 350 3 PVCX4707 1STQ007968A0000 1/1
XT4 3/4 P 350 1 PVCX4407 1STQ007967A0000 1/1
XT4 3/4 P 350 2 PVCX4607 1STQ009144A0000 1/1
XT4 3/4 P - MO 350 1 PVCX4409 1STQ007971A0000 1/1
XT4 3/4 P - RHD 350 1 PVCX4427 1STQ007973A0000 1/1
XT4 3/4 W 350 1 PVCX4410 1STQ007975A0000 1/1
XT4 3/4 W - MO 350 1 PVCX4412 1STQ007977A0000 1/1
XT4 3/4 W - RHD 350 1 PVCX4400 1STQ007979A0000 1/1
PUKI1800 XT4 4 F - RC 400 1 PVCX4423 1STQ007959A0000 1/1
PUKI2000 XT4 4 W - RC 400 1 PVCX4417 1STQ007981A0000 1/1
PFPF....
T4 3/4 F 350 1 PVCT4406 1STQ007983A0000 1/1
PFPS....
T4 3/4 F - MO 350 1 PVCT4404 1STQ007985A0000 1/1
T4 3/4 F - RHD 350 1 PVCT4406 1STQ007983A0000 1/1
T4 4 F - RC 450 1 PVCT4423 1STQ007987A0000 1/1
T5 3 P 200 1 PHCT5307 n 1STQ001467B0000 1/1
T5 3 W 300 1 PHCT5310 n 1STQ001469B0000 1/1
T5 3/4 F 400A/630A 350 1 PVCT5406 1STQ007989A0000 1/1
T5 3/4 F - MO 400A/630A 350 1 PVCT5404 1STQ007991A0000 1/1
T5 3/4 F - RHD 400A/630A 350 1 PVCT5406 1STQ007989A0000 1/1
T5 3/4 P 400A 350 1 PVCT5426 1STQ008004A0000 1/1
T5 3/4 P - RHD 400A 350 1 PVCT5426 1STQ008004A0000 1/1
Key: T5 3/4 W 400A 350 1 PVCT5414 1STQ007994A0000 1/1
T5 3/4 W - MO 400A 350 1 PVCT5412 1STQ007996A0000 1/1
F fixed T5 3/4 W - RHD 400A 350 1 PVCT5414 1STQ007994A0000 1/1
F-I fixed interlocked T5 4 F - RC 400A 450 1 PVCT5423 1STQ007999A0000 1/1
T5 4 P - RC 400A 450 1 PVCT5428 1STQ008002A0000 1/1
F - RC fixed with residual current T5 3 P 630A 450 1 PVCT5307 n 1STQ001468B0000 1/1
F - RHD fixed with Direct Rotary Handle T5 3 F 630A 450 3 PVCT5710 n 1STQ001438B0000 1/1
F&F-I fixed and fixed interlocked T5 3 W 630A 450 2 PVCT5601 n 1STQ001440B0000 1/1
P plug-in
P-I plug-in interlocked T6 3/4 F 400 1 PVCT6401 1STQ008016A0000 1/1
P - I-MO plug-in interlocked motor- T6 3/4 F - MO 400 1 PVCT6404 1STQ008019A0000 1/1
operated T6 3/4 F - RHD 400 1 PVCT6405 1STQ008022A0000 1/1
P - MO plug-in motor-operated T6 3/4 W 450 1 PVCT6414 n 1STQ008026A0000 1/1
T6 3/4 W - MO 450 1 PVCT6412 n 1STQ008028A0000 1/1
W withdrawable T6 3/4 W - RHD 450 1 PVCT6414 n 1STQ008026A0000 1/1
W-I withdrawable interlocked T7 3/4 F 450 1 PVCT7419 1STQ008034A0000 1/1
W - I-MO withdrawable interlocked T7 3/4 F - I 450 1 PVCT7419 1STQ008034A0000 1/1
motor-operated
T7 3/4 F - I-MO 450 1 PVCT7419 1STQ008034A0000 1/1
W - RC withdrawable with residual T7 3/4 F - MO 450 1 PVCT7419 1STQ008034A0000 1/1
current T7 3/4 W 500 1 PVCT7413 * 1STQ008035A0000 1/1
W - RHD withdrawable with Direct Rotary T7 3/4 W - I 500 1 PVCT7413 * 1STQ008035A0000 1/1
Handle T7 3/4 W - I-MO 500 1 PVCT7413 * 1STQ008035A0000 1/1
interlocked
T7 3/4 W - MO 500 1 PVCT7413 * 1STQ008035A0000 1/1
n
Front terminals, only Form 1 CONTINUES

1/4
No. CB
per
3
XT1 3/4 P 300 4 PVDX1807 1STQ009147A0000 1/1
XT2 3/4 F 300 4 PVDX2801 1STQ007924A0000 1/1
XT2 3/4 P 300 4 PVDX2807 1STQ007930A0000 1/1
XT3 3 P 300 4 PVDX3807 1STQ009151A0000 1/1
XT3 3/4 P 300 3 PVDX3707 1STQ009150A0000 1/1
XT4 3/4 F 300 3 PVDX4701 1STQ009143A0000 1/1
XT4 3 F 300 4 PVDX4801 1STQ007963A0000 1/1
XT4 3 P 300 4 PVDX4807 1STQ007969A0000 1/1
XT4 3/4P P 350 3 PVDX4707 1STQ009145A0000 1/1
T5 3/4 F 400A/630A 350 1 PVDT5406 1STQ008006A0000 1/1
T5 3/4 F - MO 400A/630A 350 1 PVDT5404 1STQ008007A0000 1/1
T5 3/4 F - RHD 400A/630A 350 1 PVDT5406 1STQ008006A0000 1/1
T5 3/4 P 400A 350 1 PVDT5426 1STQ008005A0000 1/1
T5 3/4 P - RHD 400A 350 1 PVDT5426 1STQ008005A0000 1/1
T5 3/4 W 350 2 PVDT5610 1STQ008480A0000 1/1
PUKI1800 T5 3/4 W 400A 350 1 PVDT5414 1STQ008008A0000 1/1
PUKI2000 T5 3/4 W - MO 350 2 PVDT5612 1STQ008481A0000 1/1
PFPF....
PFPS.... T5 3/4 W - MO 400A 350 1 PVDT5412 1STQ007997A0000 1/1
T5 3/4 W - RHD 400A 350 1 PVDT5414 1STQ008008A0000 1/1
T5 4 F - RC 400A 450 1 PVDT5423 1STQ008000A0000 1/1
T5 4 P - RC 400A 450 1 PVDT5428 1STQ008003A0000 1/1
T5 3 F 630A 450 4 PVDT5810 n 1STQ001439B0000 1/1
T5 3 W 630A 450 3 PVDT5701 n 1STQ001441B0000 1/1
T6 3/4 F 400 1 PVDT6401 1STQ008017A0000 1/1
T6 3/4 F - MO 400 1 PVDT6404 1STQ008020A0000 1/1
T6 3/4 F - RHD 400 1 PVDT6405 1STQ008023A0000 1/1
T6 3/4 W 450 1 PVDT6414 n 1STQ008027A0000 1/1
Key: T6 3/4 W - MO 450 1 PVDT6412 n 1STQ008029A0000 1/1
T6 3/4 W - RHD 450 1 PVDT6414 n 1STQ008027A0000 1/1
F fixed
T7 3/4 F 450 1 PVDT7419 1STQ008036A0000 1/1
F - I-MO fixed interlocked motor-operated T7 3/4 F - I 450 1 PVDT7419 1STQ008036A0000 1/1
F - MO fixed motor-operated T7 3/4 F - I-MO 450 1 PVDT7419 1STQ008036A0000 1/1
T7 3/4 F - MO 450 1 PVDT7419 1STQ008036A0000 1/1
F&F-I fixed and fixed interlocked T7 3/4 W 500 1 PVDT7413 * 1STQ008037A0000 1/1
P plug-in T7 3/4 W - I 500 1 PVDT7413 * 1STQ008037A0000 1/1
P - I-MO plug-in interlocked motor- T7 3/4 W - I-MO 500 1 PVDT7413 * 1STQ008037A0000 1/1
operated T7 3/4 W - MO 500 1 PVDT7413 * 1STQ008037A0000 1/1
P - MO plug-in motor-operated 48 DIN modules - W=1000mm
P - RHD plug-in with Direct Rotary Handle T5 3 W 350 4 PVFT5810 1STQ008013A0000 1/1
W withdrawable T5 3 W - MO 350 4 PVFT5812 1STQ008014A0000 1/1
W-I withdrawable interlocked T5 3/4 W 350 3 PVFT5710 1STQ008482A0000 1/1
motor-operated T5 3/4 W - MO 350 3 PVFT5712 1STQ008483A0000 1/1
W - MO withdrawable motor-operated T6 3/4 W 450 2 PVFT6610 n 1STQ008478A0000 1/1
W - RC withdrawable with residual T6 3/4 W - RHD 450 2 PVFT6610 1STQ008478A0000 1/1
current
W - RHD withdrawable with Direct Rotary T6 3/4 W - MO 450 2 PVFT6612 n 1STQ008479A0000 1/1
Handle T7 3/4 W 500 2 PVFT7633 * 1STQ008477A0000 1/1
W&W-I withdrawable and withdrawable T7 3/4 W - MO 500 2 PVFT7633 * 1STQ008477A0000 1/1
interlocked
n

System pro E power
Kit per installazione interruttori Emax 2

No. CB
per
Emax poles Version H (mm) ment code code pcs
3 Front or rear connections
E1.2 3/4 F 450 1 PVBE1241 1STQ008179A0000 1/1
E1.2 3/4 F-I 450 1 PVBE1241 1STQ008179A0000 1/1
E1.2 3/4 F 450 1 PVCE1241 1STQ008184A0000 1/1
E1.2 3/4 F-I 450 1 PVCE1241 1STQ008184A0000 1/1
E1.2 3/4 W 500 1 PVCE1240 1STQ008185A0000 1/1
E1.2 3/4 W-I 500 1 PVCE1240 1STQ008185A0000 1/1
E1.2 3/4 F 450 1 PVDE1241 1STQ008188A0000 1/1
E1.2 3/4 F-I 450 1 PVDE1241 1STQ008188A0000 1/1
E1.2 3/4 F 450 2 PVDE1262 1STQ008485A0000 1/1
E1.2 3/4 W 500 1 PVDE1240 1STQ008189A0000 1/1
PUKI1800 E1.2 3/4 W-I 500 1 PVDE1240 1STQ008189A0000 1/1
PUKI2000 PFPF.... 48 DIN modules - W=1000mm
PFPS....
E1.2 3/4 W 500 2 PVFE1263 1STQ008486A0000 1/1
Only rear connections
E2.2 3/4 F 600 1 PVCE2441 1STQ008186A0000 1/1
E2.2 3/4 F-I 600 1 PVCE2441 1STQ008186A0000 1/1
E2.2 3/4 W 600 1 PVCE2450 1STQ008187A0000 1/1
E2.2 3/4 W-I 600 1 PVCE2450 1STQ008187A0000 1/1
E4.2 3 W 600 1 PVCE4350 1STQ009991A0000 1/1
E4.2 3 W-I 600 1 PVCE4350 1STQ009991A0000 1/1
E4.2 3/4 F 600 1 PVCE2442 1STQ008484A0000 1/1
E2.2 3/4 F 600 1 PVDE2441 1STQ008190A0000 1/1
E2.2 3/4 F-I 600 1 PVDE2441 1STQ008190A0000 1/1
E2.2 3/4 W 600 1 PVDE2440 1STQ008191A0000 1/1
E2.2 3/4 W-I 600 1 PVDE2440 1STQ008191A0000 1/1
E4.2 3/4 F 600 1 PVDE2441 1STQ008190A0000 1/1
E4.2 3/4 F-I 600 1 PVDE2441 1STQ008190A0000 1/1
E4.2 3/4 W 600 1 PVDE2440 1STQ008191A0000 1/1
E4.2 3/4 W-I 600 1 PVDE2440 1STQ008191A0000 1/1
E6.2 3/4 HS F 700 1 PVFE6231 1STQ008192A0000 1/1
E6.2 3 F-I 700 1 PVFE6231 1STQ008192A0000 1/1
E6.2 3 W 700 1 PVFE6230 1STQ008193A0000 1/1
E6.2 3 W-I 700 1 PVFE6230 1STQ008193A0000 1/1
E6.2 4 HS/FS F 700 1 PVGE6231 1STQ008194A0000 1/1
Key:
E6.2 4 HS/FS F-I 700 1 PVGE6231 1STQ008194A0000 1/1
F fixed E6.2 4 HS/FS W 700 1 PVGE6230 1STQ008195A0000 1/1
W withdrawable
E6.2 4 HS/FS W-I 700 1 PVGE6230 1STQ008195A0000 1/1
HS 50% neutral To assemble these kits, order the dedicated intermediate depth uprights PUKI1800 for H= 1800mm or PUKI2000 for H=2000mm.
FS 100% neutral Order the dedicated fixed frame PFPF.... or swing frame PFPS.... for assembling internal panels.

Kits for OT
Kit for OT switch-disconnectors available up to 1600A both in horizontal and vertical version. The kit includes the
dedicated fixing brackets, the mounting plate and panels with 1/4 turn screws, hinged on the right or the left with
1/4
the dedicated PHFP0020 kit. For structure with intermediate upright.
Dimensioni Lenght
(mm)
(A) Max (B) Min.
lever shaft Lever Codice ABB Package/ 3
Description H L (mm) (mm) position ordinazione code No. pcs
Vertical installation 3/4 poles
Kits for OT 160,
350 600 80 130 ( 6) E03-E04 PKOV1660 1STQ007437A0000 1/1
200, 250
Kits for OT 160,
350 800 80 130 ( 6) E03-E04 PKOV1680 1STQ007440A0000 1/1
200, 250
Kits for OT 315,
450 600 175 95 ( 12) E03-E04 PKOV3160 1STQ008399A0000 1/1
400
Kits for OT 315,
450 800 175 95 ( 12) E03-E04 PKOV3180 1STQ008400A0000 1/1
400
Kits for OT 630,
500 600 175 70 ( 12) E03-E04 PKOV6360 1STQ007438A0000 1/1
800
Kits for OT 630,
500 800 175 70 ( 12) E03-E04 PKOV6380 1STQ007441A0000 1/1
800
PUKI1800
Kits for OT 1000,
PUKI2000 600 600 175 170 ( 12) E12-E22 PKOV1060 1STQ007439A0000 1/1
PFPF....
1250, 1600
PFPS.... Kits for OT 1000,
600 800 175 170 ( 12) E12-E22 PKOV1080 1STQ007442A0000 1/1
1250, 1600
Horizontal installation 3/4 poles
Kits for OT 160,
250 600 80 130 ( 6) E03-E04 PKOH1660 1STQ007443A0000 1/1
200, 250
Kits for OT 160,
250 800 80 130 ( 6) E03-E04 PKOH1680 1STQ007446A0000 1/1
200, 250
Kits for OT 315,
300 600 175 95 ( 12) E03-E04 PKOH3160 1STQ008401A0000 1/1
400
Kits for OT 315,
300 800 175 95 ( 12) E03-E04 PKOH3180 1STQ008402A0000 1/1
400
Kits for OT 630,
500 600 175 70 ( 12) E03-E04 PKOH6360 1STQ007444A0000 1/1
800
Kits for OT 630,
500 800 175 70 ( 12) E03-E04 PKOH6380 1STQ007447A0000 1/1
800
Kits for OT 1000,
600 600 175 170 ( 12) E12-E22 (1) PKOH1060 1STQ007445A0000 1/1
1250, 1600
Kits for OT 1000,
600 800 175 170 ( 12) E12-E22 PKOH1080 1STQ007448A0000 1/1
1250, 1600
(1)
Only low terminal covers.
(B)
(A)

System pro E power
Blind mounting plates

The kit includes the dedicated fixing brackets and the mounting plate.
Dimensions
(mm) Order ABB Package/
Blind assembly plate 150 400 PPMB1540 1STQ007521A0000 1/1
3 Blind assembly plate 250 400 PPMB2540 1STQ007523A0000 1/1
Blind assembly plate NEW 350 400 PPMB3540 1STQ002009B0000 1/1
PPMB1540 - PPMB1580 PPMB2040....PPMB6010
107
44÷159 74÷189
Flat Recessed Flat

panel panel panel
56 86 56

NEW Blind mounting plates total height
PCCM.... Dimensions
Description H W D code code No. pcs
200 Blind mounting plate 1600 400 PWRP1640 1STQ001965B0000 1/1
400
Blind assembly plate 1600 600 PWRP1660 1STQ001966B0000 1/1
Blind assembly plate 1800 400 PWRP1840 1STQ001899B0000 1/1 3
1600 Blind assembly plate 2000 400 PWRP2040 1STQ001902B0000 1/1
Tracks for front insertion
Pair of tracks for total height
300 PDRP0300 1STQ002335B0000 1/1
mounting plate
PDRP.... 500 PDRP0500 1STQ002336B0000 1/1
mounting plate
700 PDRP0700 1STQ002337B0000 1/1
mounting plate
900 PDRP0900 1STQ002338B0000 1/1
mounting plate
Crosspieces for mounting blind total height plate

Dimensions
1800 Description D (mm) code ABB No. pcs
2000
No.2 crosspieces 200 PCCM0200 1STQ007744A0000 1/2
PDRP....
If the enclosure is higher than total height mounting plate, order no. 1 PCCM.... to mount the total height blind plate.

System pro E power
Flat blind panels

Panels with 1/4 turn screws, hinged on the right or left with the dedicated PHFP0020 kit.
1/4 Dimensions
(mm)
Order ABB Package/
Flat blind panel 50 400 PPFB5040 1STQ007465A0000 1/1
3 Flat blind panel 150 400 PPFB1540 1STQ007467A0000 1/1
Flat blind panel NEW 350 400 PPFB3540 1STQ002015B0000 1/1
Flat blind panel 1800 400 PPFB1840* 1STQ007475A0000 1/1
PFPF.... Flat blind panel NEW 450 600 PPFB4560 1STQ002018B0000 1/1
PFPS.... Flat blind panel 500 600 PPFB5006 1STQ007484A0000 1/1
* Only for swing frame PFPS…. Not compatible with the hinges accessory PHFP0020.

Panels for square measuring instruments
1/4 Dimensions
(mm)
Order ABB Package/
Panel 2 instruments 72x72 200 600 PPFI2726 1STQ008092A0000 1/1
Panel 2 instruments 96x96 200 600 PPFI2966 1STQ008094A0000 1/1 3
Recessed blind panels

PPFI....
Dimensions
(mm)
Order ABB Package/
D
PPBR.... Recessed blind panel 200 400 30 PPBR2040 1STQ007723A0000 1/1
Recessed blind panel 400 400 30 PPBR4040 1STQ007724A0000 1/1
D Recessed blind panel NEW 200 600 80 PPBR2068 1STQ001399B0000 1/1
PPBR....
PPFA.... 200 800 30 PPBR2088 1STQ001400B0000 1/1
Recessed blind panel NEW

Ventilated panels
Dimensions
(mm)
Order ABB Package/
PFPF.... Ventilated panel 100 400 PPFA1040 1STQ007732A0000 1/1
PFPS....
Ventilated panel 200 400 PPFA2040 1STQ007733A0000 1/1

System pro E power
“Space-saving” column W=400mm

The “space-saving” column is composed of one reduced fixed frame (H=1800mm or H=2000mm) for W=400mm
columns with two fixed positions for the kit exclusively dedicated to: E1.2 3/4P W; E2.2 3P F; E2.2 3P W.
In order to complete this solution: blind panel H=100, 200, 300 and 600mm; modular or instrument panels H=200mm.
In this column type, it is not possible to mount kits for air-circuit breakers, moulded-case circuit breakers or modular
breakers. The only possible configurations are the following ones.
Dimensions
3 (mm) Order ABB Package/
Frame
Reduced fixed frame 1800 400 PFRF1840 1STQ009283A0000 1/1
Reduced fixed frame 2000 400 PFRF2040 1STQ009284A0000 1/1
Kit for reduced frame
E1.2 3/4 P W vertical 600 400 PRBE1243 1STQ009285A0000 1/1
E2.2 3 P F vertical 600 400 PRBE2232 1STQ009286A0000 1/1
E2.2 3 P W vertical 600 400 PRBE2233 1STQ009287A0000 1/1
Recessed blind mounting plate NEW 600 400 PBRR6040 1STQ001565B0000 1/1
Panel for reduced frame
Blind panel 100 400 PBRP1040 1STQ009288A0000 1/1
Blind recessed panel NEW 600 400 PPRR6040 1STQ001566B0000 1/1
Modular panel 200 400 PMRP2040 1STQ009292A0000 1/1
Standard DIN Rail 400 PDRS0400 1STQ008041A0000 1/1
Panel 2 instruments 72x72 200 400 PIRP2040 1STQ009293A0000 1/1
Segregation Form 2a-3a NEW
E1.2 W 600 400 PSVW6041 1STQ001568B0000 1/1
E2.2 F 600 400 PSVF6042 1STQ001569B0000 1/1
E2.2 W 600 400 PSVW6042 1STQ001570B0000 1/1
Segregation Form 3b NEW
E1.2 W 400 500 PSHW4051 1STQ001571B0000 1/1
E1.2 W 400 700 PSHW4071 1STQ001572B0000 1/1
E1.2 W 400 900 PSHW4091 1STQ001573B0000 1/1
E2.2 F 400 700 PSHF4072 1STQ001574B0000 1/1
Key: E2.2 F 400 900 PSHF4092 1STQ001575B0000 1/1
F fixed E2.2 W 400 700 PSHW4072 1STQ001576B0000 1/1
W withdrawable E2.2 W 400 900 PSHW4092 1STQ001577B0000 1/1
100
300 100
100 100
200
100
Fixed
600 600 position
Fixed
position
100
2000 200
100 100
1800 200
100
Fixed
600 position
600 Fixed
position
100
100 300 100
200
100 100

Accessories and spare parts
DIN rail accessories

With fixed frame for panels, maximum wiring ducts dimension is 60x60mm.
ABB Package/
Description Code code No. pcs
Supports for horizontal wiring ducts
No.4 plastic supports for horizontal wiring ducts AD1009* 1STQ008200A0000 1/4
No.4 plastic supports for horizontal wiring ducts AD1037* 1STQ008201A0000 1/4
3
AD1009 AD1037 No.4 metal supports reduced wiring ducts PSRM1515** 1STQ009164A0000 1/4
Depth adapter
Depth adapter for Tmax T1-T2-T3-XT1-XT3
AP6000 1STQ008202A0000 1/1
W=600mm
* To be used in case of not segregated DIN rail with panels H≥200mm.

** To be used in case of DIN rail with panels H=300mm (2 DIN rail) or always in case of segregated DIN rail.
AP6000
Universal cable holder brackets

ABB Package/
EV0036 No.5 cable holder D=28,5mm EV0036 1STQ006605A0000 1/5
EV0037
No.5 cable holder D=55mm EV0037 1STQ006627A0000 1/5
Angled supports for terminal boxes and earthing busbars

EV1110
EV2110
ABB Package/
EV1112 No.50 angled supports 1 row of terminals EV1110 1STQ001007A0000 1/50
EV2112
No.10 angled supports 1 row of terminals EV2110 1STQ003202A0000 1/10
EV1111 No.10 angled supports double row of terminals EV1111 1STQ001008A0000 1/10
No.50 angled supports 1 row of terminals + earth EV1112 1STQ001009A0000 1/50

System pro E power
Din rail and support for cable duct

With fixed frame for panels, maximum wiring ducts dimension is 60x60mm.
EV0042
ABB Package/
AD1009
No.4 horizontal/vertical support for cable duct EV0042 1STQ006589A0000 1/4
No. 4 plastic supports for horizontal wiring ducts AD1009 1STQ008200A0000 1/4
Hole covering strip RAL7035 colour

ABB Package/No.
Description Code code pcs
hole covers W=2000mm, grey AD1086 1STQ009173A0000 1/10
AD1600
Panel Accessories
AD1800
ABB Package/
INO AD1086 No. 20 label holders 24 DIN mod AD1600 1STQ008205A0000 1/20
AZZ
AG
IM
LU C No. 20 label holders 36 DIN mod AD1800 1STQ008206A0000 1/20
No.10 hole covers W=2000mm, grey AD1086 1STQ009173A0000 1/10
No. 288 labels 1 DIN mod. 15x17mm (HxW) AD1101 (1) 1STQ008207A0000 1/288
No. 192 labels 2 DIN mod. 15x27mm (HxW) AD1102 (1)
1STQ008208A0000 1/192
AD1101÷AD1104 No. 96 labels 3 DIN mod. 15x50mm (HxW) AD1103 (1) 1STQ008209A0000 1/96
No. 96 labels 4 DIN mod. 15x67mm (HxW) AD1104 (1) 1STQ008210A0000 1/96
(1)
Labels can be written using compatible Grafoplast system.

Closing plug for instrument holder panels
ABB Package/No.
EV1137 Description Code code pcs
No.10 closing plug for instrument holder panels
EV1135 1STQ001023A0000 1/10
72x72mm
No.5 closing plug for instrument holder panels
EV1136 1STQ001024A0000 1/5
96x96mm
No.50 closing plugs for pushbuttons Ø22mm EV1137 1STQ001025A0000 1/50
3
EV1135
EV1136
Hinges for panels

Hinges kit for panels (blind, instruments, recessed and vented panels). Not suitable for blind panels H=1800/2000mm.
ABB Package/
No. 20 hinges for frontal panels PHFP0020 1STQ008111A0000 1/20
For the mounting of the internal panels order the fixed PFPF…. or swing PFPS…. dedicated frame
Spare parts Tmax XT cover plate for DIN rail

AD3301
AD3302 ABB Package/
AD3303 Description Code code No. pcs
AD3304
Cover plate for Tmax XT1 3P mounted on DIN rail AD3301 1STQ008301A0000 1/1
Cover for panel XT1 3P mounted on plate AD3305 1STQ009216A0000 1/1
Cover for panel XT2 3P mounted on plate AD3306 1STQ009217A0000 1/1
AD3305
AD3306 Cover for panel XT3 3P mounted on plate AD3307 1STQ009218A0000 1/1
AD3307
AD3308 Cover for panel XT4 3P mounted on plate AD3308 1STQ009219A0000 1/1

System pro E power
Dedicated solution
CombiLine
Quick selection guide 4/4
Order codes 4/8
InLine II
Quick selection guide 4/22
Order codes 4/24

System pro E power
CombiLine-M - General information
Modular distribution panel system CombiLine-M

The right module for every type of application up to 850A.
The perfect expansion of the modular cabinet series is no problem with the CombiLine-M modular distribution panel system.
Fast, efficient and easy to combine - just three product features of this system that speak for themselves.
The result: maximum options using a minimum of components.
GU-modules 13
250-500-750
GU-modules 12 1000-1250
250-500-750
1000-1250 50
150
150 150
150 150
150 150
150 150
150 2000 150
150 150
1800
150 150
150 150
150 150
150 150
150 150
150 150

Integration in System pro E power
CombiLine-M solutions can be fitted in five different columns widths and is compatible with any enclosure depth.
The fitting of CombiLine-M solutions is realized thanks to the use of a dedicated fixing set as well as a touchguard.
An additional cover is needed for the enclosures with functional height 2000mm.

System pro E power
CombiLine-M - Quick selection guide
H=1800mm recommended installation solutions
GU-modules 12
Functional Esternal
Uprights Structure crosspieces H=100mm plinth Top/bottom panels Front/rear/side panels
Galvanized sheet metal Galvanized sheet metal
In≤4000A ** In≤4000A ** Top/Bottom Bottom Rear panel
Without
Plinth flanges Blind Open(2) plinth Blind
Height Height Galvanized
1800mm 2013mm sheet
W D W D PW- metal ** Front/ Angle Front/ IP30(1) IP30(1)
(mm) (mm) (mm) (mm) mod. In≤4000A Rear Sides pieces Rear Sides IP65 IP40(1) IP65 IP40(3) IP65 IP40(1)
250 500 350 616 1 PUPM1800 PCFM0250 PCFM0500 PPAM0100 PPFM1025 PPFM1050 PTBB2556 PTBB2550 PTBO2550 PBWP2550 PPEB1825 PPEB1827
200 316 PCFM0200 PPFM1020 PTBB1220
PPRB1820(4)
1250 500 1350 616 5 PUPM1800 PCFM1250 PCFM0500 PPAM0100 PPFM1250 PPFM1050 PTBB1250 PTBO1250 PBWP1250
PPLB1820(5)
Consult page 2/12 and 7/2 for selection of the protection class.
* The external dimensions include the H=100mm plinth and the panels.
** Also available in stainless steel, see page 2/8.
(1)
In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit, page 2/23.
(2)

4
COMBILINE
Finishing profiles IP30
Side panel 12/24/36/48 mod. DIN 12/24/36/48 mod. DIN
Vented Blind Vented
IP30(1) Vertical Horizontal Depth

IP30(1) IP65 IP40(1) IP30(1) IP65 IP40(1) IP65 IP40(1) profile profile Touch-guard Bracket WR frame support(8)
PPEB1826 PPEB1820
PPEB1836 PPEB1830 PPEA1830
PPEB1856 PPEB1850 PPEA1850 PDLB1826 PDLB1825 PPFV1800 PPFH0250 PCTG1825 PBCM0004 WR181
PPEB1826 PPEB1820
PPEB1856 PPEB1850 PPEA1850 PDLG1856 PDLG1850 PDLB1856 PDLB1850 PPFV1800 PPFH0500 PCTG1850 PBCM0004 WR281
PPEB1826 PPEB1820
PPEA1875 PPEB1856 PPEB1850 PPEA1850 PDLG1876 PDLG1870 PDLB1876 PDLB1875 PPFV1800 PPFH0750 PCTG1875 PBCM0004 WR381
PPEB1826 PPEB1820 PDFC0200
PPEB1836 PPEB1830 PPEA1830 PDFC0300
WR281
PPEB1856 PPEB1850 PPEA1850 PDLG1816 PDLG1810 PDLB1816 PDLB1810 PPFV1800 PPFH1000 PCTG1810 PBCM0004 PDFC0500
WR381
PPRA1820 (4)
PDLB8120(6) PDLB8120(6) WR281
PPEB1856 PPEB1850 PPEA1850 PPFV1800 PPFH1250 PCTG1812 PBCM0004 PDFC0500
PPLA1820(5) PDLG8500(7) PDLB8500(7) WR381
Bottom for switchboard without plinth complete with the dedicated set of brackets, which can
(3) (5)
be ordered separately. (6)
(4)
Right rear panel for structures W=1250mm. (7)
(8)
Order the RZ1P4 older for two frame.
This are standard configurations can be calculated with the software.

System pro E power
CombiLine-M - Quick selection guide
H=2000mm recommended installation solutions
GU-modules 13
Functional Esternal
Galvanized sheet metal Galvanized sheet metal
In≤4000A ** In≤4000A ** Top/Bottom Bottom Rear panel
Without
2000mm 2213mm sheet
W D W D PW- metal ** Front/ Angle Front/ IP30(1) IP30(1)
(mm) (mm) (mm) (mm) mod. In≤4000A Rear Sides pieces Rear Sides IP65 IP40(1) IP65 IP40(3) IP65 IP40(1)
200 316 PCFM0200 PPFM1020 PTBB1220
PPRB2020(4)
1250 500 1350 616 5 PUPM2000 PCFM1250 PCFM0500 PPAM0100 PPFM1250 PPFM1050 PTBB1250 PTBO1250 PBWP1250
PPLB2020(5)
Consult page 2/12 and 7/2 for selection of the protection class.
* The external dimensions include the H=100mm plinth and the panels.
** Also available in stainless steel, see page 2/8.
(1)
In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit, page 2/23.
(2)

4
COMBILINE
Side panel 12/24/36/48 mod. DIN 12/24/36/48 mod. DIN
Vented Blind Vented
Adaptor
IP30(1) Vertical Horizontal Touch- for height Depth
IP30(1) IP65 IP40(1) IP30(1) IP65 IP40(1) IP65 IP40(1) profile profile guard Bracket 2000mm WR frame support(8)
PPEB2026 PPEB2020
PPEB2056 PPEB2050 PPEA2050 PDLB2026 PDLB2025 PPFV2000 PPFH0250 PCTG2025 PBCM0004 PCCM2025 WR191
PPEB2026 PPEB2020
PPEB2056 PPEB2050 PPEA2050 PDLG2056 PDLG2050 PDLB2056 PDLB2050 PPFV2000 PPFH0500 PCTG2050 PBCM0004 PCCM2050 WR291
PPEB2026 PPEB2020
PPEA2075 PPEB2056 PPEB2050 PPEA2050 PDLG2076 PDLG2070 PDLB2076 PDLB2075 PPFV2000 PPFH0750 PCTG2075 PBCM0004 PCCM2075 WR391
WR291
PPEB2056 PPEB2050 PPEA2050 PDLG2016 PDLG2010 PDLB2016 PDLB2010 PPFV2000 PPFH1000 PCTG2010 PBCM0004 PCCM2010 PDFC0500
WR391
PPRA2020(4) PDLB2120(6) PDLB2120(6) WR291
(5) PPEB2056 PPEB2050 PPEA2050 PPFV2000 PPFH1250 PCTG2012 PBCM0004 PCCM2012 PDFC0500
PPLA2020 PDLG2500(7) PDLB2500(7) WR391
Bottom for switchboard without plinth complete with the dedicated set of brackets, which can
(3) (5)
be ordered separately. (6)
(4)
Right rear panel for structures W=1250mm. (7)
Order the RZ1P4 older for two frame and PBMC0001 adaptor for
(8)
CombiLine H=2000mm.
This are standard configurations can be calculated with the software.

System pro E power
CombiLine-M - Order codes
Touch guard profile - dedicated solution for CombiLine-M

Profile to guarantee IP20 touch protection with CombiLine-M modules installed.
Dimensions
(mm)
Order ABB Package/
Touch Guard profile 1800 250 PCTG1825 1STQ009368A0000 1/1
Touch Guard profile 1800 1250 PCTG1812 1STQ001319B0000 1/1
4 Touch Guard profile 2000 250 PCTG2025 1STQ009379A0000 1/1
Touch Guard profile 2000 1250 PCTG2012 1STQ001320B0000 1/1
Fixing set - dedicated solution for CombiLine-M

Fixed set for the adaptation of standard WR frame on System pro E power structure.
Order ABB Package/
CombiLine-M fixing set PBCM0004 1STQ009354A0000 1/4
Depth support
No.2 CombiLine crosspieces for frame D=200mm PDFC0200 1STQ001929B0000 1/2
No.2 adaptor for Combiline H=2000mm PBMC0001 1STQ001934B0000 1/2
Height adapters for 2000mm columns - dedicated solution for CombiLine-M

Adapters to use CombiLine-M modules in columns with functional height 2000mm. The components cover 50mm
on the bottom and on the top.
Dimensions
(mm)
Order ABB Package/
CombiLine-M adapter 2000 250 PCCM2025 1STQ009355A0000 1/2
CombiLine-M adapter 2000 1250 PCCM2012 1STQ001318B0000 1/2
Uprights – Galvanized sheet metal *

Dimensions
* Also available in stainless steel, see page 2/15.

Structure crosspieces – Galvanized sheel metal *
Depth and width crosspieces for structures in galvanized sheet metal. For applications with In ≤4000A.
Dimensions
(mm)
Order ABB Package/
Width crosspieces
No.4 width crosspieces galvanized sheet metal 1250 PCFM1250 1STQ007044A0000 1/4 4
Depth crosspieces
PPAM0100
Universal angle pieces for plinths in galvanized sheet metal

PPAM0200 Dimen-
pre-assembled*
*Order no. 2 pieces of H=100mm covering flange kits to complete the H=200mm plinth.
Plinth flanges
Dimensions (mm)
Order ABB Package/
Side plinth flanges

System pro E power

Dimensions
(mm)
Order ABB Package/
IP65 blind top/bottom 250 200 PTBB2526 1STQ001270B0000 1/1
IP65 blind top/bottom 250 300 PTBB2536 1STQ007071A0000 1/1
4 IP65 blind top/bottom 250 500 PTBB2556 1STQ007072A0000 1/1


the top and the bottom, please order two quantities of the same code or two different top/bottom codes according
Dimensions
(mm)
Order ABB Package/
Blind Top/Bottom IP30, 40 250 200 PTBB2520 1STQ001267B0000 1/1
4

System pro E power
Top sealing kit IP31/IP41

Dimensions (mm)
Order ABB Package/
4 Top sealing kit IP31/IP41 400 200 PKPT4020 1STQ008066A0000 1/1

Top sealing kit IP31/IP41 *
Dimensions
(mm)
Order ABB Package/
4

System pro E power
Open Top/Bottom
In order to reach IP65 protection degree, use the dedicated fixed cable incoming flanges PFCF….; in order to
reach IP40 protection degree, use the dedicated swinging cable incoming flanges PFCS…. at page 4/13-4/14.
Open Top/Bottom 250 200 PTBO2520 1STQ001272B0000 1/1
4 Open Top/Bottom 250 300 PTBO2530 1STQ007132A0000 1/1
Bottom without plinth IP40

Bottom without plinth IP40 250 200 PBWP2520 1STQ001279B0000 1/1
Bottom without plinth IP40 250 300 PBWP2530 1STQ007168A0000 1/1

Dimensioni (mm) Order ABB Package/

Fixed incoming cable flange 250 200 PFCF2520 1STQ001274B0000 1/1
Fixed incoming cable flange 500 200 PFCF5020 1STQ001290B0000 1/1 4
Fixed incoming cable flange 1250 900 2xPFCF6090 1STQ007674A0000 1/1

Dimensioni (mm)
Order ABB Package/
No.2 sliding flanges 500 900 PFCS5090 1STQ001293B0000 1/2
No.2 sliding flanges 750 900 PFCS7590 1STQ001309B0000 1/2
No.2 sliding flanges 1250 900 2xPFCS6090 1STQ007707A0000 1/2

System pro E power

Dimensions
(mm)
Order ABB Package/
4 Blind rear panel IP65 1800 1000 PPEB1816 1STQ007585A0000 1/1

Dimensions
(mm)
Order ABB Package/
1800 1250
left PPLB1820 1STQ007617A0000 1/1
2000 1250
left PPLB2020 1STQ007628A0000 1/1

In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit PKPT...., page 4/12.
Dimensions
No. (mm)
Vented Order ABB Package/
Vented rear panel right PPRA1820 1STQ007639A0000 1/1
IP30/31 with gasket 6 1800 1250
left PPLA1820 1STQ007640A0000 1/1
Vented rear panel IP30 right PPRA2020 1STQ007649A0000 1/1
with gasket 4 2000 1250
left PPLA2020 1STQ007650A0000 1/1
4

Dimensions
(mm)
Order ABB Package/

it is necessary to add the proper top sealing kit PKPT...., page 4/12.
Dimensions
(mm)
Order ABB Package/

System pro E power

Pickled sheet steel without gasket. The code refers to one single side panel. In order to reach IPX1 protection
degree it is necessary to add the proper top sealing kit PKPT...., page 4/12.
Dimensions
(mm)
4 Vented side panel IP30 2 2000 300 PPEA2030 1STQ007641A0000 1/1

sealing kit PKPT...., page 4/12.
Order ABB Package/

Glass door IP65

Dimensions (mm)
Order ABB Package/

Glass door
Glass door IP65 1800 500 PDLG1856 1STQ009414A0000 1/1

Glass door IP40
to add the proper top sealing kit PKPT...., page 4/12. Doors can be mounted both on the front and on the back
of the enclosures.
Dimensions
Glass door
Glass door IP40 1800 750 PDLG1870 1STQ009397A0000 1/1 4
Blind door IP65

tubes for W>400mm
Dimensions
(mm)
Order ABB Package/
Blind door IP65 1800 250 PDLB1826 1STQ009376A0000 1/1

System pro E power
Blind door IP40

Dimensions
(mm)
Order ABB Package/
Blind door IP40/IP41 1800 250 PDLB1825 1STQ009377A0000 1/1
4 Blind door IP40/IP41 1800 500 PDLB1850 1STQ009413A0000 1/1

add the proper top sealing kit PKPT...., page 4/12.
Dimensions
(mm)
Order ABB Package/
Crosspiece for horizontal busbar assembly under top or on bottom of structure

For assembly in D>300mm structures with internal cable compartment, order PCCM.... cable compartment depth.
Description W (mm) code code No.pcs
Intermediate crosspiece for bus-
250 PCKI0250 1STQ001328B0000 1/1
bars under top/on bottom
500 PCIS0500 1STQ009165A0000 1/1
750 PCKI0750 1STQ001330B0000 1/1
1000 PCKI1000 1STQ008103A0000 1/1
1250 PCKI1250 1STQ008104A0000 1/1

Configuration example
Functional dimensions 2000x750x500mm (HxWxD) structure with H=100mm plinth, adapted to CombiLine-M fixing. WR frame and
CombiLine-M modules to be added.
Quantity Order code Part Description

1 PUPM2000 Structure No. 4 galvanized sheet uprights H=2000mm
1 PCFM0750 Structure No. 4 width stainless steel crosspieces W=750mm
1 PCFM0500 Structure No. 4 depth galvanized sheet crosspieces D=500mm
1 PPAM0100 Structure No. 4 corners plinth H=100mm
1 PPFM1075 Structure No. 2 front/rear plinth flanges W=750mm
1 PPFM1050 Structure No. 2 side plinth flanges D=500mm
2 PTBB7550 External covers IP30/31, 40/41 blind top/bottom W=750mm D=500mm
1 PPEB2077 External covers IP30/31, IP40/41 blind back panel H=2000mm W=750mm
2 PPEB2050 External covers IP30/IP31, IP40/IP41 blind side panel H=2000mm D=500mm
1 PDLB2075 External covers IP40/IP41 blind door H=2000mm W=750mm
1 PCTG2075 CombiLine-M adaptors Touch Guard profile H2000 W750
1 PBCM0004 CombiLine-M adaptors CombiLine-M fixing set
1 PCCM2075 CombiLine-M adaptors CombiLine-M adapter H=2000 W=750

System pro E power
InLine II - General information
Introduction
The latest technology of Fuse Switch Disconnectors. The new generation InLine II ensures the best stability and the highest safety in the
power distribution network during operation and service.
Feature InLine II ZLBM/ZHBM

Rated operational voltage Ue [V] 400 / 500 / 690
Rated operational current Ie [A] 125…630

4

System pro E power
InLine II - Quick selection guide
Recommended installation solutions
H=1800mm
Functional Esternal
Galvanized sheet metal Intermediate Galvanized sheet metal
In≤4000A * upright In≤4000A * Top/Bottom Bottom Rear panel
Without
1800mm 1913mm sheet
W D W D metal * Front/ Angle Front/ IP30(1) IP30(1)
(mm) (mm) (mm) (mm) In≤4000A Rear Sides pieces Rear Sides IP65 IP40(1) IP65 IP40(3) IP65 IP40(1)
600 700 700 816 PUPM1800 PCFM0600 PCFM0700 PUKI1800 PPMA0100 PPFM1060 PPFM1070 PTBB6076 PTBB6070 PTBO6070 PBWP2570 PPEB1866 PPEB1860
H=2000mm
Functional Esternal
Galvanized sheet
metal Intermediate Galvanized sheet metal
In≤4000A * upright In≤4000A * Top/Bottom Bottom Rear panel
Without
2000mm 2013mm sheet
W D W D metal * Front/ Angle Front/ IP30(1) IP30(1)
(mm) (mm) (mm) (mm) In≤4000A Rear Sides pieces Rear Sides IP65 IP40(1) IP65 IP40(3) IP65 IP40(1)
* Also available in stainless steel, see page 2/8. Bottom for switchboard without plinth complete with the dedicated set of brackets, which can
(3)
Consult page 2/12 and 7/2 for selection of the protection class. be ordered separately.
(1)
In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit,
page 2/23.
(2)

4
INLINE II
Glass door 24/36/48 Blind door 24/36/48
Side panel mod. DIN mod. DIN
Vented Blind Vented
IP30(1) Vertical Horizontal

IP30(1) IP65 IP40(1) IP30(1) IP65 IP40(1) IP65 IP40(1) profile profile InLine II kit Fixed frame Front panels
PPEA1860 PPEB1876 PPEB1870 PPEA1870 PDLG1866 PDLG1860 PDLB1866 PDLB1860 PPFV1800 PPFH0600 PKNL1260 PFNL1860 No.2 PPNL3060
INLINE II
Glass door 24/36/48 Blind door 24/36/48

Side panel mod. DIN mod. DIN
Vented Blind Vented
IP30(1) Vertical Horizontal

IP30(1) IP65 IP40(1) IP30(1) IP65 IP40(1) IP65 IP40(1) profile profile InLine II kit Fixed frame Front panels

System pro E power
InLine II - Order codes
InLine II mounting kit

Kit for the fixing of InLine II fuseholders
Dimensions
(mm)
Order ABB Package/
InLine mounting kit + front panel 1200 600 PKNL1260 1STQ009823A0000 1/1
Fixed frame for InLine II panels

Fixed frame for InLine II internal panels. InLine II fixed frame allows to fit only InLine II panels listed below.
Dimensions
(mm)
Order ABB Package/
Fixed frame for panels in the InLine column 1800 600 PFNL1860 1STQ001372B0000 1/1
Flat blind panels for InLine II fixed frame

These panels are dedicated to InLine II fixed frame only.
Dimensions
(mm)
Order ABB Package/
Blind flat panel for InLine column 300 600 PPNL3060 1STQ001378B0000 1/1
Order 2 pieces for a complete structure.
InLine II dummy modules

Dummy InLine II to cover free space in the enclosure and guarantee touch protection.
Dimensions
(mm)
Order ABB Package/
Description W code code No. pcs
InLine vertical compensator 50 PCNL0050 1STQ009406A0000 1/1
InLine vertical compensator 100 PCNL0100 1STQ009368A0000 1/1

Uprights – Galvanized sheet metal *
Dimensions
(mm) Order Codice Package/
Description H code ABB No. pcs
Structure crosspieces – Galvanized sheel metal *

Depth and width crosspieces for structures in galvanized sheet metal. For applications with ≤4000A.
Dimensions
(mm)
Order ABB Package/
Width crosspieces
Depth crosspieces
Intermediate upright for internal kit assembly

Intermediate depth upright for assembling kits for Tmax and Emax 2. The intermediate uprights are not required
for assembling fixed Tmax XT1, XT2, XT3, XT4, T4, T5, T6 and XT1, XT3 with Direct Rotary Handle only in non-
segregated structures. Order 2 uprights for the kits.
Dimensions
(mm)
Order ABB Package/
Intermediate upright for internal kits 1800 PUKI1800 1STQ008039A0000 1/1
Intermediate upright for internal kits 2000 PUKI2000 1STQ008040A0000 1/1

System pro E power
PPAM0100 Universal angle pieces for plinths in galvanized sheet metal

Dimen-
PPAM0200
pre-assembled*
4 *Order no. 2 pieces of H=100mm covering flange kits to complete the H=200mm plinth.
Plinth flanges
Dimensions (mm)
Order ABB Package/
Side plinth flanges

Dimensions (mm)
Order ABB Package/
Blind Top/Bottom IP65 800 500 PTBB8056 1STQ007096A0000 1/1 4

the top and the bottom, please order two quantities of the same code or two different top/bottom codes according
Dimensions
(mm)
Order ABB Package/

System pro E power

Dimensions
(mm)
Order ABB Package/
4 IP65 blind top/bottom 250 500 PTBB2556 1STQ007072A0000 1/1


Top sealing kit IP31/IP41 *
Dimensions
(mm)
Order ABB Package/
N.2 roof profiles for single column 900 PKST0900 1STQ001914B0000 1/2 4

System pro E power
Open Top/Bottom
In order to reach IP65 protection degree, use the dedicated fixed cable incoming flanges PFCF….; in order to
reach IP40 protection degree, use the dedicated swinging cable incoming flanges PFCS…. at page 4/28-4/29.
Dimensions
(mm)
Order ABB Package/
4 Open Top/Bottom 600 500 PTBO6050 1STQ007149A0000 1/1
Internal bottom IP40

Dimensions
(mm)
Order ABB Package/

Dimensioni
(mm)
Order ABB Package/

Dimensioni
(mm)
Order ABB Package/
No.2 sliding flanges 800 700 PFCS8070 1STQ007713A0000 1/2 4

Dimensions
(mm)
Order ABB Package/

Dimensions
(mm)
Order ABB Package/

System pro E power

In order to reach IPX1 protection degree it is necessary to add the proper top sealing kit PKPT...., page 4/27.
Dimensions
No. (mm)
Vented Order ABB Package/
4 Vented rear panel IP30 4 2000 800 PPEA2080 1STQ007646A0000 1/1

Dimensions
(mm)
Order ABB Package/

it is necessary to add the proper top sealing kit PKPT...., page 4/27.
Dimensions
(mm)
Order ABB Package/

Pickled sheet steel without gasket. The code refers to one single side panel. In order to reach IPX1 protection
degree it is necessary to add the proper top sealing kit PKPT...., page 4/27.
Dimensions
(mm)
Vented side panel IP30 2 2000 500 PPEA2050 1STQ007643A0000 1/1 4

sealing kit PKPT...., page 4/27.
Order ABB Package/

Glass door IP65

Dimensions (mm)
Cable
Glass door

System pro E power
Glass door IP40

to add the proper top sealing kit PKPT..., page 4/27. Doors can be mounted both on the front and on the back
of the enclosures
Dimensions
(mm)
4 Glass door
Blind door IP65

tubes for W>400mm
Dimensions
(mm)

Blind door IP40/IP41
Dimensions
(mm)
Blind door IP40/IP41 24 1800 600 PDLB1860 1STQ007363A0000 1/1
4

add the proper top sealing kit PKPT..., page 4/27.
Dimensions (mm)
Order ABB Package/

System pro E power
Configuration example
Functional dimensions 1800x800x700mm (HxWxD) structure with H=100mm plinth, InLine II kits and front panels covers.
Quantity Order code Part Description

1 PUPM1800 Structure No. 4 galvanized sheet uprights H=1800mm
1 PCFM0800 Structure No. 4 width galvanized sheet crosspieces W=800mm
1 PCFM0700 Structure No. 4 depth galvanized sheet crosspieces D=700mm
1 PPAM0100 Structure No. 4 corners plinth H=100mm
1 PPFM1080 Structure No. 2 front/rear plinth flanges W=800mm
1 PPFM1070 Structure No. 2 side plinth flanges D=700mm
2 PUKI2000 Kits No. 1 Intermediate upright
1 PTBB8076 External covers IP65 blind top/bottom W=800mm D=700mm
1 PPEB1886 External covers IP65 blind back panel H=1800mm W=800mm
2 PPEB1876 External covers IP65 blind side panel H=1800mm D=700mm
1 PDLG1886 External covers IP65 36 DIN modules glass door H=1800mm W=800mm
1 PFNL1880 InLine II components Fixed frame for panels in the InLine column H=1800mm W=800mm
2 PPNL3080 InLine II components Blind flat panel for InLine column H=300mm W=800mm
System pro E power
Selection guides 5/6

Crosspieces and brackets overview 5/6
Linear system
Fixing busbar holders to the structure 5/8
Choice of busbar holders and closing crosspieces 5/10
Choice and assembly of the number of busbar holders 5/16
Scaled system
Fixing busbar holders to the structure 5/18
Choice of busbar holders in relation to rated current In (A) and IP
protection class 5/19
Choice and assembly of the number of busbar holders 5/20
5
Compensators and connections for flat and shaped busbar 5/22
Flexible busbars up to 1250 A 5/24
Flat drilled and threaded busbars for earthing connection 5/24
Modular dividers 5/25
Codes for ordering 5/28

Main distribution systems 5/28
Accessories 5/38

System pro E power
General information
The distribution systems that can be used inside System pro E power switchboards
meet the requirements of all applications, with 250A to 6300A configurations.
The new System pro E power distribution system has been designed for improved flexibility and simple busbar connections. Linear and
scaled solutions are available and allow the busbars to be installed in any position: horizontally, under the top, on the bottom and at
each height; vertically, along the side or at the rear and in the cable compartment. The structural components include:
- insulating support and tie rods
- crosspieces and brackets
The main advantages are:
- same construction philosophy for 250A to 6300A applications
- same multifunction insulating supports able to house flat busbars 5 and 10mm thick and shaped busbars ( “click in” installation
method for the linear version)
- the center distance between phases can be increased for the linear version by simply sliding the insulation support fastenings along
5
the crosspieces
- same fixing crosspieces for both linear and scaled solutions
- stainless steel crosspieces for applications with In ≥ at 4000A to limit the effect of stray currents
The capacity of the busbars is as follows:
- flat copper busbars up to 6300A
- shaped profile busbars up to 2500A
Air and moulded-case circuit-breakers can be connected to the busbars by means of prefabricated rigid or flexible connections.
Number of busbars installable per insulator

Linear System Scaled System
Flat 1,2,3 or 4 bars 50mm block 2000A 1 or 2 busbars 2000A
busbars per phase 75mm block 3200A per phase
100mm block 6300A
Shaped 1 per phase 50mm block 1600A 1 per phase 1600A
busbars 75mm block 2000A
75mm block 2500A
The crosspieces that fix to

the structure are for universal
use for both linear and scaled
busbar holders.
The linear and scaled insulating

supports house 5mm flat
busbar systems on one side,
while the other side houses
shaped profile or 10mm section
flat busbar systems.
One single tie rod in different

lengths is used to fasten all
types of busbars.

The linear busbar holder is formed by inserting, with a “click”, the insulating supports
onto the crosspieces, which are fixed directly inside the switchboard by means of
simple brackets.
LINEAR SYSTEM
The new busbar holder consists of:

- a polyamide insulating support (maximum operating temperature 130 °C) featuring shaped grooves for the busbars and pins for fixing
to the crosspieces, able to house both flat and shaped profile busbars;
- crosspieces available in different lengths, made of hot-dip galvanized steel sheet for In <4000A current values or crosspieces in AISI
304 stainless steel for In ≥4000A current values.
The crosspiece is an integral part of the busbar holder and is fixed directly inside the cubicle with the purpose-made brackets. In 5
addition, it can also be used as a universal crosspiece thanks to 5.5mm diameter round holes on the side and 10mm diameter holes for
fixing the cage nuts.
Lastly, the crosspieces can be coupled on the external side to make the busbar system sturdier.
Since the insulating supports are modular, the center distance between the phases can be increased by spacing them at a 12.5mm
pitch.
The tie rods that fix the insulating supports are made of thermoplastic material (for In <4000A current values). They are available in a
single length of 195mm and can be adjusted to suit the busbars installed. The AISI 304 stainless steel tie rods (for In ≥4000A current
values) are available for 120mm, 160mm and 200mm busbars.
The linear system can house flat busbars (5 and 10mm thick) and shaped profile busbars in copper.
The center distance between phases can be increased

by 12.5mm by simply sliding the insulation supports
along the crosspieces. When the distance between
phases is increased, the length of the closing
crosspiece must also be increased.

System pro E power
General information
Advantages
- scalability: structure with modular insulating supports for 3P or 4P
- saving: the 4P system does not always have a full section neutral: the insulating supports allow structures of different sizes or with
fewer insulating supports to be created, thus reducing costs.
- modularity: the linear system allows the center distance between the phases to be increased by spacing them at a 12.5mm pitch
instead of installing them one against the other.
- sturdiness: the crosspieces can be coupled on the external side to make the busbar system sturdier.
Busbars installable with the insulating supports of the linear system

Length of No. Flat busbars per
insulating support Notes phase Slot dimensions Maximum busbar H Minimum busbar H
50mm can house busbars on 1x10mm 12mm slot 120x10 25x10
5
both sides 2x5mm 9.5mm slot 120x5 20x5
both sides 4x5mm 12mm slot 125x5 25x5
both sides 2x10mm 12mm slot 120x10 25x10
All the shaped busbars can be housed in the insulating supports on a level with the slots for 10mm busbars.
All the insulators are

reversible and can
house:
5mm and 10mm
flat busbars and
all shaped profile
busbars

The scaled busbar holder can house flat busbars up to 2000A or shaped busbars up
to 1600A.
SCALED SYSTEM
The insulating support is a single unit that can be screwed onto the crosspiece with the aid of a threaded spacer. The linear system is
connected to the distribution busbars with tie rods, which are the same for all types of busbars.
Busbar system
- One single busbar support in thermoplastic that can house both flat busbars (5 and 10mm thick) and shaped profile busbars, thanks
to the shape of the insulating support
- The same fixing crosspieces are used both for linear and scaled solutions
5
Busbars installable with the insulating supports of the scaled system
No. Flat busbars per
Insulating support Notes phase Slot dimensions Maximum busbar H Minimum busbar H
One type of can house busbars on 1x10mm 12mm slot 120x10 30x10
insulating support both sides 2x5mm 9.5mm slot 125x5 20x5
All the shaped busbars can be housed in the insulating supports on a level with the slots for 10mm busbars.
The scaled insulating

supports house
5mm flat busbar
systems on one
side, while the other
side houses 10mm
flat busbars and
all shaped profile
busbars.

System pro E power
Selection guides
LINEAR SYSTEM - FLAT BUSBARS AND SHAPED BUSBARS

Fixing busbar holders to the structure.
A B1 B2 B3 B4 PCKI....
B5
PCKI....
5 PCKI.... PCKI....
For vertical busbars in structure D>=500mm, the intermediate upright is always necessary
A - Vertical busbars at the rear of the

structure B1 - vertical busbars on the side of the structure
B2/B3 - vertical busbars with orizontal busbars in the structure under the top/on the bottom
B4/B5 - vertical busbars in the cable compartment with orizontal busbars top/bottom (1)
SUPPORTS FOR FIXING CROSSPIECES FOR BUSBAR HOLDERS (1 piece per busbar holder)
CROSSPIECES TO THE
STRUCTURE * Crosspiece in
(2 pieces per crosspiece) Crosspiece in Crosspiece in stainless steel for
Crosspiece in stainless Crosspiece in galvanized sheet Crosspiece in In≥4000A +
Structure galvanized steel for Structure galvanized sheet metal + interme- stainless steel for intermediate
W (mm) sheet metal In≥4000A D (mm) metal diate upright In≥4000A(5) upright
200 PCRM0188
300 PCRM0288 300 PCRM0288
400 PCRM0388 PCRS0388
500 PCRM0488 PCRM0238
600 PCRM0588 PCRS0588
PBBU0008
700 PCRM0688 PCRM0438 PCRS0438
800 PCRM0788 PCRS0788
900 PCRM0888 PCRM0638 PCRS0888 PCRS0638
1000 PCRM0988 PCRS0988
See example page 5/8-5/9 1250 PCRM1238 PCRS1238
(1)
Use busbars with 100x10mm maximum section for structures with internal cable compartment L=200mm with orizontal busbars top/bottom.
10mm
5mm

C PCKI.... C1 D1 D2 D3
PCKI.... 5
For vertical busbars in structure D>=500mm, the intermediate upright is always necessary
C/C1 - Horizontal busbars under the top or on the D1 - Horizontal busbars at any height of the structure and internal cable compartment
bottom of the structure (2) D2 - Vertical busbars in the cable compartment with orizontal busbars in the structure at any hight (3)
D3 - Horizontal busbars at any hight in side by side structures and vertical busbars in the internal cable
compartment
Crosspiece in
galvanized sheet Crosspiece in Crosspiece in Crosspiece in
metal + stainless steel for galvanized sheet stainless steel for
intermediate In≥4000A(4) + Crosspiece in metal + Crosspiece in In≥4000A +
Structure crosspiece intermediate Structure galvanized sheet intermediate stainless steel for intermediate
D (mm) PCKI.... crosspiece PCKI.... D (mm) metal (5) upright In≥4000A(4) upright
200 PCRM0188
300 PCRM0288
500 PCRM0238 500 PCRM0488 PCRM0238
700 PCRM0438 PCRS0438 700 PCRM0688 PCRM0438 PCRS0438
900 PCRM0638 PCRS0638 900 PCRM0888 PCRM0638 PCRS0888 PCRS0638
(2)
Order crosspieces PCKI.... to assemble busbars under the top or on the bottom, for assembly in D>300mm structures with internal cable compartment, order PCCM....
cable compartment depth crosspieces as well.
(3)
Use busbars with 80x10mm maximum section for structures with internal cable compartment L=200mm. With orizontal busbars in the structure at any hight.
(4)
In structures without intermediate upright, swing frame PFPS.... cannot be installed with horizontal busbars at all height.
* The new bracket, PBBU0008 is not compatible with the old ones (PBBT0008, PBBV0008, PBBH0004), on the same busbar system, both horizontal and vertical, it is not
possible the coexisting between old and new ones. The fixing of the crosspieces for busbar system must be done with only one kind of bracket.

System pro E power
Examples of use
Example of busbars installation *

A B1 PBBU0008 PBBT0008 PBBV0008
Vertical busbars at vertical busbars
the rear of the on the side of the
structure structure
B2/B3 PBBU0008 PBBT0008 PBBV0008 PBBT0008

Vertical busbars with orizontal busbars
in the structure
PCKI....
PCKI....
C/C1
Horizontal busbars under the top or on the
bottom of the structure
PCKI....
PCKI....
* The new bracket, PBBU0008 is not compatible with the old ones (PBBT0008, PBBV0008, PBBH0004), on the same busbar system, both horizontal and vertical, it is not
possible the coexisting between old and new ones. The fixing of the crosspieces for busbar system must be done with only one kind of bracket.

B4/B5 PBBU0008 PBBT0008 PBBV0008
vertical busbars in the cable compartment
with orizontal busbars in the structure
MAX MAX
100mm 100mm
200mm 200mm
D1 D2 D3
Horizontal busbars at any height of the Vertical busbars in the cable compartment with Horizontal busbars at any hight in side by side structures
structure and internal cable compartment orizontal busbars in the structure at any hight and vertical busbars in the internal cable compartment
PBBU0008 PBBU0008 PBBT0008 PBBU0008 PBBV0008
PBBH0004
PBBH0004 PBBH0004
200mm 200mm
MAX MAX
80mm 100mm

System pro E power
Examples of use
Example use of crosspieces

Fixing between uprights and crosspieces
PBBV0008 PBMC0002
PBBT0008
PBBU0008
Fixing between crosspieces

PBBV0008 PBBT0008 PBMC0002
Earth fixing Neutral fixing

PBRP0002 PBRN0002

Crosspieces selections
Length To be fitted in the following
Description Enclosure [mm] functional dimensions Code
Crosspieces with “C” profile Structure 188 200 PCRM0188
without
288 300 PCRM0288
intermediate
upright 388 400 PCRM0388
488 500 PCRM0488
588 600 PCRM0588
688 700 PCRM0688
788 800 PCRM0788
888 900 PCRM0888
988 1000 PCRM0988
5
1238 1250 PCRM1238
Structure with 238 500 with intermediate upright PCRM0238
vertical
338 600 with intermediate upright PCRM0338
intermediate
upright 438 700 with intermediate upright PCRM0438
Any type 2013 To be cut according to the need PCRM2013
Crosspieces with intermediate upright Any type 300 300 PCKI0300
profile
400 400 PCKI0400
600 600 PCKI0600
800 800 PCKI0800
1000 1000 PCKI1000
1250 1250 PCKI1250
1800 1800 PUKI1800
2000 2000 PUKI2000

System pro E power
Selection guides
LINEAR SYSTEM - COPPER FLAT BUSBARS

Choice of busbar holders and closing crosspieces in relation to the rated
current In (A) and IP protection class.
PBHB1125 PBHB2145 PBHB3121
50 75 100 D1
10 10 10 10 10 10
L1 L2 L3
5
5 5 5 5 5 5 10 10
Description Recommended D1 (busbar/

circuit-breaker/connection interaction) minimum 3 pole
3 poles
Closing cross-
piece
3-pole busbar
Capacity Number of busbars Section Busbars holders
In (A) per phase (mm) D1≥300 D1≥700 D1=900 L1 L2 L3 1 piece (1)
IP30 / IP31
250 1 20x5 n 3xPBFC2005 PCRM0188
400 1 25x5 n 3xPBFC2505 PCRM0188
630 1 40x5 n 3xPBFC4005 PCRM0188
800 1 30x10 n 3xPBFC3010 PCRM0188
1000 1 80x5 n 3xPBFC8005 PCRM0188
1 40x10 n 3xPBFC4010 PCRM0188
1250 1 100x5 n 3xPBFC1005 PCRM0188
1 50x10 n 3xPBFC5010 PCRM0188
1600 2 80x5 n 6xPBFC8005 PCRM0188
1 80x10 n 3xPBFC8010 PCRM0188
2000 2 100x5 n 6xPBFC1005 PCRM0188
2 50x10 n 6xPBFC5010 PCRM0288
2500 4 80x5 n 12xPBFC8005 PCRM0288
2 80x10 n 6xPBFC8010 PCRM0288
3200 4 100x5 n 12xPBFC1005 PCRM0288
2 100x10 n 6xPBFC1001 PCRM0288
4000 3 100x10 n 9xPBFC1001 PCRM0338 (2)
IP30 / IP31 / IP40 / IP41
5000 3 160x10 n 9xPBFC1601 PCRS0338
7000 3 200x10 n 9xPBFC2001 PCRS0338
IP40 / IP41 / IP65
250 1 20x5 n 3xPBFC2005 PCRM0188
400 1 32x5 n 3xPBFC3205 PCRM0188
630 1 50x5 n 3xPBFC5005 PCRM0188
800 1 63x5 n 3xPBFC6305 PCRM0188
1000 2 40x5 n 6xPBFC4005 PCRM0188
1250 1 100x5 n 3xPBFC1005 PCRM0188
1600 1 100x10 n 3xPBFC1001 PCRM0188
2000 1 120x10 n 3xPBFC1201 PCRM0188
2000 2 60x10 n 6xPBFC6010 PCRM0288
2500 2 100x10 n 6xPBFC1001 PCRM0288
3200 3 100x10 n 9xPBFC1001 PCRM0338
4000 3 120x10 n 9xPBFC1201 PCRS0338
(1)
When busbars with increased center distance are installed, the length of the closing crosspiece must also be increased.
(2)
Use sheet metal crosspiece and nylon tie rods.

D2 D2 D2
L1 L2 L3 N 100% L1 L2 L3 N 50% L1 L2 L3 N 50%
180°
Overall dimensions
crosspieces supports
4 poles 4-pole D2 (mm) Insulators (4) Tie rods (5)
100% Neutral 50% Neutral
Number Closing crosspiece 3 poles 6 3 poles 4
of bus- Number 4-pole busbar pieces pieces
bars per Section busbars Section Busbars L1 L2 L3 holders 4 poles 8 4 poles5
phase (mm) 100% N per phase (mm) 50%N 1 piece (1) D2≥300 D2≥700(3) D2=900(3) pieces pieces
1 20x5 4xPBFC2005 - - - PCRM0238 n PBHB1125 PTRN1951

1 40x10 4xPBFC4010 1 40x5 PBFC4005 PCRM0238 n PBHB1125 PTRN1951
1 80x10 4xPBFC8010 1 80x5 7xPBFC8005 PCRM0238 n PBHB1125 PTRN1951
3 100x10 12xPBFC1001 2 100x10 11xPBFC1001 PCRM0438 (2) n PBHB3121 PTRN1951(2)
3 160x10 12xPBFC1601 2 160x10 11xPBFC1601 PCRS0438 n PBHB3121 PTRS1601


(3)
Excluding D=500mm with intermediate upright.
(4)
The pack contains 24 pieces.
(5)

System pro E power
Selection guides
LINEAR SYSTEM - CUPONAL FLAT BUSBARS

Choice of busbar holders and closing crosspieces in relation to the rated current In (A)
and IP protection class.
PBHB1125 PBHB2145 PBHB3121
50 75 100 D1
10 10 10 10 10 10
L1 L2 L3
5
5 5 5 5 5 5 10 10
Description Recommended D1 (busbar/

circuit-breaker/connection interac-
tion) minimum 3 pole 3 poles
Closing crosspiece
3-pole busbar
Capacity Number of busbars Section Busbars holders
In (A) per phase (mm) D1≥300 D1≥700 L1 L2 L3 1 piece (1)
IP30 / IP31
250 1 20x5 n 3xPBFA2005 PCRM0188
400 1 30x5 n 3xPBFA3005 PCRM0188
630 1 50x5 n 3xPBFA5005 PCRM0188
800 1 40x10 n 3xPBFA4010 PCRM0188
1000 1 50x10 n 3xPBFA5010 PCRM0188
1000 2 40x5 n 6xPBFA4005 PCRM0188
1250 1 75x10 n 3xPBFA7510 PCRM0188
1250 2 60x5 n 6xPBFA6005 PCRM0188
1600 2 80x5 n 6xPBFA8005 PCRM0188
2000 1 120x10 n 3xPBFA1201 PCRM0188
2000 4 50x5 n 12xPBFA5005 PCRM0288
2500 2 80x10 n 6xPBFA8010 PCRM0288
2500 4 80x5 n 12xPBFA8005 PCRM0288
3200 2 120x10 n 6xPBFA1201 PCRM0288
IP40 / IP41 / IP65
250 1 25x5 n 3xPBFA2505 PCRM0188
400 1 40x5 n 3xPBFA4005 PCRM0188
630 1 60x5 n 3xPBFA6005 PCRM0188
800 1 80x5 n 3xPBFA8005 PCRM0188
1000 2 50x5 n 6xPBFA5005 PCRM0188
1250 1 80x10 n 3xPBFA8010 PCRM0188
1600 1 100x10 n 3xPBFA1001 PCRM0188
2000 2 75x10 n 6xPBFA7510 PCRM0288
2500 2 100x10 n 6xPBFA1001 PCRM0288
3200 3 100x10 n 9xPBFA1001 PCRM0338
(1)

D2 D2 D2
L1 L2 L3 N 100% L1 L2 L3 N 50% L1 L2 L3 N 50%
180°
Overall dimensions
100% Neutral 50% Neutral Closing
Number crosspiece 3 poles 6 3 poles 4
of bus- Number 4-pole busbar pieces pieces
bars per Section busbars Section Busbars L1 L2 L3 holders 4 poles 8 4 poles5
phase (mm) 100% N per phase (mm) 50%N 1 piece (1) D2≥300 D2≥700(2) D2=900(2) pieces pieces
1 20x5 4xPBFA2005 - - - PCRM0238 n PBHB1125 PTRN1951

1 40x10 4xPBFA4010 1 40x5 PBFA4005 PCRM0238 n PBHB1125 PTRN1951
2 40x5 8xPBFA4005 1 40x5 7xPBFA4005 PCRM0238 n PBHB1125 PTRN1951

(2)
(3)
(4)

System pro E power
Selection guides
LINEAR SYSTEM - SHAPED BUSBARS

Choice of busbar holders and closing crosspieces in relation to rated
current In (A) and IP protection class.
PBHB1125 PBHB2145 D1
50 75
L1 L2 L3
10 10
5
Recommended D1 (busbar/
circuit-breaker/connection
interaction) minimum 3 pole 3 poles
Number of Closing
busbars WxW Section crosspiece 3-pole busbar holder
Capacity In (A) per phase (mm) (mm2) Busbars D1≥300 D1≥500 D1≥700 L1 L2 L3 1 piece
IP30/31 IP40/41 IP65
475 440 400 1 30x10 165 PBSC0400 n 3xPBSC0400 PCRM0188

D2 D2
L1 L2 L3 N 100% L1 L2 L3 N 50%
5
Overall dimensions
Closing crosspiece
4-pole busbar holder 3 poles 6 pieces 3 poles 4 pieces
100% Neutral 50% Neutral 1 piece (1) D2≥300 D2≥500 D2≥400(2) 4 poles 8 pieces 4 poles 5 pieces
4xPBSC0400 - PCRM0238 n PBHB1125 PTRN1951

4xPBSC2500 3xPBSC2500 + 1xPBSC2000 PCRM0338 n PBHB2145 PTRN1951
(1)
(2)
(4)
(5)

System pro E power
Selection guides
LINEAR SYSTEM - FLAT BUSBARS AND SHAPED BUSBARS

Choice and assembly of the number of busbar holders, in relation to maximum Icw
Use of the correct number of busbar holders guarantees electrodynamic stress withstand in the event of a short-circuit. Establish the maximum distance
(X max) which must not be exceeded between two consecutive busbar holders, in relation to the maximum Icw.
1/4 X
1/4 X
The distance between the first busbar holder and
the end of the busbar must not exceed 1/4 of “X”.
5
Copper busbars
Description No. busbar holders Lenght =1750mm in relation to Icw max
Capacity Number of
In (A) busbars per WxW
IP30/31 IP40/41 IP65 phase (mm) Busbar Insulators 15 kA X max 25 kA X max 36 kA X max 50 kA X max 65 kA X max 75 kA X max 85 kA X max
FLAT BUSBARS
250 250 250 1 20x5 PBFC2005 PBHB1125 7 275 - - - - - - - - - - - -
400 - - 1 25x5 PBFC2505 PBHB1125 7 300 9 200 - - - - - - - - - -
- 400 400 1 32x5 PBFC3205 PBHB1125 5 450 7 275 - - - - - - - - - -
630 - - 1 40x5 PBFC4005 PBHB1125 5 450 7 300 9 200 - - - - - - - -
- 630 630 1 50x5 PBFC5005 PBHB1125 5 475 7 300 9 225 - - - - - - - -
800 - - 1 30x10 PBFC3010 PBHB1125 4 525 5 450 7 300 - - - - - - - -
- 800 800 1 63x5 PBFC6305 PBHB1125 4 525 5 425 6 325 - - - - - - - -
1000 - - 1 40x10 PBFC4010 PBHB1125 4 525 5 450 6 375 9 225 - - - - - -
- 1000 1000 2 40x5 PBFC4005 PBHB1125 4 525 5 475 6 375 - - - - - - - -
1000 - - 1 80x5 PBFC8005 PBHB1125 4 525 5 475 6 375 9 225 - - - - - -
1250 1250 1250 1 100x5 PBFC1005 PBHB1125 3 1000 4 525 6 375 7 275 - - - - - -
1250 - - 1 50x10 PBFC5010 PBHB1125 3 1000 4 525 6 375 8 250 9 200 - - - -
- 1600 1600 1 100x10 PBFC1001 PBHB1125 3 1000 4 550 4 500 6 325 9 200 - - - -
1600 - - 1 80x10 PBFC8010 PBHB1125 3 1000 4 525 5 475 7 300 9 200 - - - -
1600 - - 2 80x5 PBFC8005 PBHB1125 3 1000 4 525 5 475 7 300 9 200 - - - -
2000 - - 2 100x5 PBFC1005 PBHB1125 3 1000 4 550 4 500 6 325 9 200 - - - -
- 2000 2000 1 120x10 PBFC1201 PBHB1125 3 1000 4 550 4 500 6 325 9 200 - - - -
2000 - - 2 50x10 PBFC5010 PBHB2145 3 1000 4 525 6 375 8 250 9 200 - - - -
- 2000 2000 2 60x10 PBFC6010 PBHB2145 3 1000 4 525 6 375 8 250 9 200 - - - -
2500 - - 2 80x10 PBFC8010 PBHB2145 3 1000 3 1000 4 525 5 400 7 275 9 200 - -
2500 - - 4 80x5 PBFC8005 PBHB2145 3 1000 3 1000 4 525 5 400 7 275 9 200 - -
3200 2500 2500 2 100x10 PBFC1001 PBHB2145 3 1000 3 1000 4 525 5 400 7 300 7 275 8 250
3200 - - 4 100x5 PBFC1005 PBHB2145 3 1000 3 1000 4 525 5 400 7 275 9 200 - -
4000 3200 3200 3 100x10 PBFC1001 PBHB3121 3 1000 3 1000 3 750 4 500 5 400 6 350 7 275
- 4000 4000 3 120x10 PBFC1201 PBHB3121 3 1000 3 1000 3 750 4 500 5 400 6 350 7 275
5000 5000 - 3 160x10 PBFC1601 PBHB3121 3 1000 3 1000 3 1000 3 750 5 400 6 350 7 275
7000 7000 - 3 200x10 PBFC2001 PBHB3121 3 1000 3 1000 3 1000 3 750 5 400 6 350 7 275
SHAPED BUSBARS
475 440 400 1 30x10 PBSC0400 PBHB1125 4 525 5 450 - - - - - - - - - -
655 643 630 1 35x10 PBSC0630 PBHB1125 4 525 5 450 7 300 - - - - - - - -
958 840 800 1 45x10 PBSC0800 PBHB1125 4 525 5 450 6 375 - - - - - - - -
1342 1220 1000 1 67x10 PBSC1000 PBHB1125 4 525 5 450 6 375 9 225 - - - - - -
1418 1338 1250 1 70x10 PBSC1250 PBHB1125 3 1000 4 525 6 375 8 250 - - - - - -
1857 1744 1600 1 95x10 PBSC1600 PBHB1125 3 1000 4 550 5 400 7 275 9 200 - - - -
2354 2200 2000 1 105x15 PBSC2000 PBHB2145 3 1000 4 550 4 500 6 325 9 225 9 200 - -
2860 2750 2500 1 105x15 PBSC2500 PBHB2145 3 1000 3 1000 4 525 5 400 7 275 9 200 - -

5
Cuponal busbars
Capacity Number of
In (A) busbars per WxW
100 kA X max 120 kA X max IP30/31 phase (mm) Busbar Insulators 15 kA X max 25 kA X max 36 kA X max 50 kA X max 65 kA X max
FLAT BUSBARS IP30/31
- - - -
250 1 20x5 PBFA2005 PBHB1125 10 225
- - - -
- - - - 400 1 30x5 PBFA3005 PBHB1125 10 225 13 175
- - - - 630 1 50x5 PBFA5005 PBHB1125 7 275 10 225 13 175
- - - -
- - - - 800 1 40x10 PBFA4010 PBHB1125 6 325 7 275 10 225
- - - - 1000 1 50x10 PBFA5010 PBHB1125 6 325 7 275 9 250 13 175
- - - -
1000 2 40x5 PBFA4005 PBHB1125 6 325 7 275 9 250 13 175
- - - -
- - - - 1250 1 75x10 PBFA7510 PBHB1125 4 500 6 325 9 250 10 225
- - - -
1250 2 60x5 PBFA6005 PBHB1125 4 500 6 325 9 250 12 200 13 175
- - - -
- - - - 1600 2 80x5 PBFA8005 PBHB1125 4 500 6 325 7 275 10 225 13 175
- - - -
2000 1 120x10 PBFA1201 PBHB1125 4 500 6 325 6 325 9 250 13 175
- - - -
- - - - 2000 4 50x5 PBFA5005 PBHB2145 4 500 6 325 9 250 12 200 13 175
- - - - 2500 2 80x10 PBFA8010 PBHB2145 4 600 4 500 6 325 7 275 10 225
- - - -
- - - - 2500 4 80x5 PBFA8005 PBHB2145 4 600 4 500 6 325 7 275 10 225
- - - - 3200 2 120x10 PBFA1201 PBHB2145 4 600 4 500 6 325 7 275 10 225
- - - -
FLAT BUSBARS IP40/41/65
9 225 - -
- - - - 250 1 25x5 PBFA2505 PBHB1125 10 225
9 200 - - 400 1 40x5 PBFA4005 PBHB1125 7 275 10 225
9 200 - -
630 1 60x5 PBFA6005 PBHB1125 7 275 10 225 13 175
9 200 9 200
9 200 9 200 800 1 80x5 PBFA8005 PBHB1125 6 325 7 275 9 250
1000 2 50x5 PBFA5005 PBHB1125 6 325 7 275 9 250

- - - -
- - - - 1250 1 80x10 PBFA8010 PBHB1125 4 500 6 325 9 250 10 225
- - - -
1600 1 100x10 PBFA1001 PBHB1125 4 500 6 325 6 325 9 250 13 175
- - - -
- - - - 2000 2 75x10 PBFA7510 PBHB2145 4 500 6 325 9 250 12 200 13 175
- - - - 2500 2 100x10 PBFA1001 PBHB2145 4 600 4 500 6 325 7 275 10 225
- - - -
- - - - 3200 3 100x10 PBFA1001 PBHB3121 4 600 4 500 4 500 6 325 7 275

System pro E power
Selection guides
SCALED SYSTEM-FLAT BUSBARS

NEW A
Fixing busbar holders to the structure.
PBBU0008
PCR....
SUPPORTS FOR FIXING CROSSPIECES TO THE STRUCTURE (2 pieces per crosspiece)

A - Vertical busbars at the side of the structure
PBBV0008 (1)
PBBU0008 (2)
5 CROSSPIECES FOR BUSBAR HOLDERS (1 piece per busbar holder)
Crosspiece in
Structure Crosspiece in galvanized sheet metal +
P (mm) galvanized sheet metal intermediate upright
300 PCRM0288
500 PCRM0488 PCRM0238
700 PCRM0688 PCRM0438
900 PCRM0888 PCRM0638
(1)
Use busbars with 50x10mm maximum section for structures with internal cable compartment L=200mm.
(2)
Available from 2016.
Choice of busbar holders in relation to rated current In (A) and IP protection class.
Copper busbars PBHS1125 PBHB1125
50
10
5 5 L1 L2 L3 N 50% L1 L2 L3 N
Switchboard
installation
Number Minimum depth (mm) 3/4-pole insulator Insulators 3 poles 4 poles
Capacity of busbars WxW complete with tie 6 pieces for 3 poles Busbars L1 L2 L3+ Busbars L1 L2 L3+
In (A) per phase (mm) D≥300 D≥700 rods(1) 8 pieces for 4 poles (2) Busbars L1 L2 L3 x100% Neutral x50% Neutral
IP30 / IP31
250A 1 20x5 n PBHS1125 PBHB1125 3xPBFC2005 4xPBFC2005
1000A 1 40x10 n PBHS1125 PBHB1125 3xPBFC4010 4xPBFC4010 3xPBFC4010+1xPBFC4005
1600A 2 80x5 n PBHS1125 PBHB1125 6xPBFC8005 8xPBFC8005 7xPBFC8005
IP40 / IP41 / 65
(1)
The package contains 1 scaled busbar holder provided with nylon tie-rods.
(2)

SCALED SYSTEM-FLAT BUSBARS
Cuponal busbars PBHS1125 PBHB1125
50
10
5 5 L1 L2 L3 L1 L2 L3 N
Switchboard
installation
Minimum depth (mm) 3 poles 4 poles
Number 3/4-pole insulator Insulators
Capacity of busbars WxW complete with tie 6 pieces for 3 poles Busbars L1 L2 L3+ Busbars L1 L2 L3+
In (A) per phase (mm) D≥300 D≥700 rods(1) 8 pieces for 4 poles (2) Busbars L1 L2 L3 100% Neutral x50% Neutral 5
IP30 / IP31
250 1 20x5 n PBHS1125 PBHB1125 3xPBFA2005 4xPBFA2005
800 1 40x10 n PBHS1125 PBHB1125 3xPBFA4010 4xPBFA4010 3xPBFA4010+1xPBFA4005
1000 2 40x5 n PBHS1125 PBHB1125 6xPBFA4005 8xPBFA4005 7xPBFA4005
IP40 / IP41 / 65
(1)
(2)
SCALED SYSTEM - SHAPED BUSBARS

PBHS1125 PBHB1125
50
10
L1 L2 L3 L1 L2 L3 N
Switchboard
installation 3/4-pole
Number of Minimum insulator Insulators
busbars WxW Section depth (mm) complete with 6 pieces for 3 poles 3 poles 4 polies
Capacity In (A) per phase (mm) (mm2) D≥300 tie rods(1) 8 pieces for 4 poles (2) Busbars L1 L2 L3 Busbars L1 L2 L3+100% Neutral
IP30/31 IP40/41 IP65
475 440 400 1 30x10 165 n PBHS1125 PBHB1125 3xPBSC0400 4xPBSC0400
(1)
(2)

System pro E power
Selection guides
SCALED SYSTEM - FLAT BUSBARS AND SHAPED BUSBARS

Choice and assembly of the number of busbar holders, in relation to maximum Icw
Use of the correct number of busbar holders guarantees electrodynamic stress withstand in the event of a short-circuit. Establish the maximum distance
(X max) which must not be exceeded between two consecutive busbar holders, in relation to the maximum Icw.
1/4 X
1/4 X
5 The distance between the first busbar holder and

the end of the busbar must not exceed 1/4 of “X”.
Copper busbars
Capacity In (A) Number
of bus-
bars per
IP30/31 IP40/41 IP65 phase WxW (mm) BUSBAR Insulators 15 kA X max 25 kA X max 36 kA X max
FLAT BUSBARS
250 250 250 1 20x5 PBFC2005 PBHS1125 9 200 - - - -
400 - - 1 25x5 PBFC2505 PBHS1125 7 300 - - - -
- 400 400 1 32x5 PBFC3205 PBHS1125 7 300 9 200 - -
630 - - 1 40x5 PBFC4005 PBHS1125 7 300 9 200 - -
- 630 630 1 50x5 PBFC5005 PBHS1125 5 450 7 275 9 200
800 - - 1 30x10 PBFC3010 PBHS1125 5 450 6 375 9 225
- 800 800 1 63x5 PBFC6305 PBHS1125 4 525 5 425 6 325
1000 - - 1 40x10 PBFC4010 PBHS1125 4 525 5 450 6 375
- 1000 1000 2 40x5 PBFC4005 PBHS1125 4 525 5 475 7 300
1000 - - 1 80x5 PBFC8005 PBHS1125 4 525 5 475 6 375
1250 1250 1250 1 100x5 PBFC1005 PBHS1125 4 525 4 525 6 375
1250 - - 1 50x10 PBFC5010 PBHS1125 4 525 4 525 6 375
- 1600 1600 1 100x10 PBFC1001 PBHS1125 4 550 4 550 5 475
1600 - - 1 80x10 PBFC8010 PBHS1125 4 525 4 525 5 475
1600 - - 2 80x5 PBFC8005 PBHS1125 4 525 4 525 6 375
2000 - - 2 100x5 PBFC1005 PBHS1125 4 550 5 425 6 375
- 2000 2000 1 120x10 PBFC1201 PBHS1125 4 550 4 550 5 475
SHAPED BUSBARS
475 440 400 1 30x10 PBSC0400 PBHS1125 5 450 6 375 9 225
655 643 630 1 35x10 PBSC0630 PBHS1125 5 450 6 375 9 225
958 840 800 1 45x10 PBSC0800 PBHS1125 4 525 5 425 6 325
1342 1220 1000 1 67x10 PBSC1000 PBHS1125 4 525 5 450 6 375
1418 1338 1250 1 70x10 PBSC1250 PBHS1125 4 525 4 525 6 375
1857 1744 1600 1 95x10 PBSC1600 PBHS1125 4 550 4 550 5 475

5
Cuponal busbars
Capacity Number
In (A) of bus-
bars per WxW
50 kA X max IP30/31 phase (mm) BUSBAR Insulators 15 kA X max 25 kA X max 36 kA X max 50 kA X max
FLAT BUSBARS IP30/31
- - 250 1 20x5 PBFA2005 PBHS1125 13 175
- -
400 1 30x5 PBFA3005 PBHS1125 10 225
- -
- - 630 1 50x5 PBFA5005 PBHS1125 10 225 13 175
- - 800 1 40x10 PBFA4010 PBHS1125 7 275 9 250 13 175
- -
1000 1 50x10 PBFA5010 PBHS1125 6 325 7 275 9 250 13 175
9 200
9 200 1000 2 40x5 PBFA4005 PBHS1125 6 325 7 275 9 250 13 175
- - 1250 1 75x10 PBFA7510 PBHS1125 6 325 6 325 9 250 12 200
9 200
1250 2 60x5 PBFA6005 PBHS1125 6 325 6 325 9 250 12 200
8 250
8 250 1600 2 80x5 PBFA8005 PBHS1125 6 325 6 325 9 250
6 325 2000 1 120x10 PBFA1201 PBHS1125 6 325 7 275 9 250

7 300
FLAT BUSBARS IP40/41/65
- -
- - 250 1 25x5 PBFA2505 PBHS1125 13 175
7 300 400 1 40x5 PBFA4005 PBHS1125 10 225 13 175
630 1 60x5 PBFA6005 PBHS1125 7 275 10 225 13 175

- -
- - 800 1 80x5 PBFA8005 PBHS1125 6 325 7 275 9 250 13 175
9 200 1000 2 50x5 PBFA5005 PBHS1125 6 325 7 275 10 225

9 200
1250 1 80x10 PBFA8010 PBHS1125 6 325 6 325 9 250 12 200
8 250
6 325 1600 1 100x10 PBFA1001 PBHS1125 6 325 6 325 7 275 9 250

System pro E power
Selection guides
Compensators and connections for flat and shaped busbar
Shaped busnbars
In 400A 630A 800A 1000A 1250A 1600A 2000A 2500A
In
400A PFCB4080 PFCB4080
1000A PFCB1016 PFCB1016
Shaped busbars
1250A PFCB1016 PFCB1016

5 1600A PFCB1016 PFCB2025 PFCB2025
2000A 2x PFCB2025 2x PFCB2025
2500A 2x PFCB2025
PFCB4080 – Connections between shaped busbar/shaped busbar or shaped busbar/flat busbar for 400A, 630A, 800A
PFCB1016 – Connections between shaped busbar/shaped busbar or shaped busbar/flat busbar for 1000A, 1250A, 1600A
PFCB2025 – Connections between shaped busbar/shaped busbar or shaped busbar/flat busbar for 2000A, 2500A
PFCC0023 – Compensator for configurations compose of no. of busbar per phase>1
The connections can be used also for joining flat busbar/ shaped busbar (as per the chart above) if the following conditions are fulfilled:
- use of insulating support of the same size both in H and in V
- use of flat busbar with 10mm thickness
In case of joining a main flat busbar system composed of more than one busbar per phase and shaped busbar distribution system, it is
recommended to align the shaped busbar to the flat busbar in the most rearward position.
The number of code for connection shall be multiplied by the number of phases included into the busbars system.
Example
Connection between shaped busbars 2500A and flat busbars 2500A
3P busbars system 6 x PFCB2025 + 3 x PFCC0029

4P busbars system 8 x PFCB2025 + 4 x PFCC0029

Flat busbars
800A 1000A 1250A 1600A 2000A 2000A 2500A 3200A 3200A 4000A 5000A 6300A
1 Busbar for phase 2 Busbars for phase 3 Busbars for phase
PFCB4080 PFCB4080 + PFCC0023
PFCB2025 PFCB2025 + PFCC0023 5
2x PFCB2025 + PFCC0023
2x PFCB2025 + PFCC0023
Examples of use
Flat busbars 2 for phase Flat busbars 2 for phase Flat busbars 3 for phase Flat busbars 3 for phase
Shaped busbar ≤ 2000A Shaped busbar ≥ 2000A Shaped busbar ≤ 1600A Shaped busbar ≥ 2000A
PFCB4080 or PFCB1016 or PFCB2025 2 x PFCB2025 + PFCC0023 PFCB4080 or PFCB1016 or PFCB2025 2 x PFCB2025 + PFCC0023
+ PFCC0023
Examples of busbars junction

System pro E power
Selection guides
Flexible busbars up to 1250A

Capacity (A) Dimensions
Section
In No. busbar/ WxW dimensions Lenght Weight
(A) Code phase IP31 IP41 IP65 (mm) (mm2) (mm) (kg)
15.5x3
160 PBFC0160 1 160 46.5 2000
20x3
250 BF1602 1 395 323 250 60 2000 1,42
20x5
400 BF2502 1 498 460 400 100 2000 2,15
24x6
500 BF4002 1 660 620 500 144 2000 3
5 32x5
630 BF4012 1 758 702 630 160 2000 3,36
40x8
1000 BF6302 1 1203 1140 1000 320 2000 6,33
50x10
1250 BF8002 1 1515 1390 1250 500 2000 9,68
Flat drilled and threaded busbars for earthing connection

Cross-section Code Threading Pitch (mm) WxW (mm) Lenght (mm) AxB (mm)
EV1119 6 MA 20 20x5 2000
5 20 6MA
20
EV1120 6 MA 20 25x5 2000

5 20 6MA
25
6MA
EV1121 6MA 25 50x5 2000
5 25
50
EV1122 6MA 34x30

A
EV1123 8MA 34x30
B EV1124 6MA 40x50
EV1125 8MA 40x50

Modular dividers
Single-pole Three-poles
Code AD1076 AD1080(1) AD1007 D1081(2) AD1030 AD1031 AD1075 AD1006

In IEC (A) 125 125 160 160 250 400 125 160
UL (A) 115 115 175 160 230 310 115 175
Icw (kA) 4.4 4.2 11 1.1 21 21 4.4 11
Version pole 1 1 1 1 1 1 3 3
Installation DIN35/plate DIN35/plate DIN35/plate DIN35/plate DIN35/plate DIN35/plate DIN35/plate DIN35/plate
power supply Ø cable (mm2) min. 10 6 16 10 35 95 10 16
max 35 35 70 70 120 185 35 70
5
No. outgoing feeder Ø cable (mm2) 1,5÷10 4 4
2,5÷16 10 6 10 6 5 5 6 6
2,5÷25 2 2
Dimensions HxWxD (mm) 71x45x42,5 74x27x47 71x45x42,5 92x35x49 95.5x45x49 95.5x45x49 71.5x80x42,5 71.5x80x42,5
No. DIN modules 2,5 1,5 2,5 2 3 3 4.5 4.5
Rated service voltage Ue (V) 1000 Vac 1000 Vac 1000 Vac 1000 Vac 1000 Vac 1000 Vac 1000 Vac 1000 Vac
1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc 1500 Vdc
Degree of protection IP 20 20 20 20 20 20 20 20
Mark
Three-poles
Code AD1004 AD1028 AD1029 AD1027 AD1034 AD1053

In (A) 125 125 125 160 250 250
Icw (kA) 10 4.2 4.2 6.2 15 15
Ipk (kA) 24 25 25 20 30 30
Version poli 4.2 4 4 4 30 30
Installation DIN35/plate DIN35/plate DIN35/plate DIN35 4 4
power supply Ø cable (mm2) min. 6 6 6 10 with AD1038 brackets with AD1038 brackets
max 35 25 with cable terminal 25 with cable terminal 50
No. outgoing feeder Ø cable (mm ) 2
1/6 5/phase No. 22 holes M5 with No. 32 holes M5 with
17,5mm pitch per phase 17,5mm pitch per phase
1.5/6 4/neutral
(threaded busb. (threaded busb.
1.5/10 2/phase 7 9 20x5mm) 20x5mm)
6/neutral
1.5/16 2
2.5/16 8
6/25 2 2 3
Dimensions HxWxD (mm) 74.5x98x45 93x89x48 96x126x48 90x160.5x50 150x600x70 150x800x70
No. DIN modules 5,5 5 7 9 24 36
Rated service voltage Ue (V) 1000 Vac 440 440 440 500 500
1500 Vdc
Degree of protection IP 20 20 20 20
Mark UL UL UL UL UL UL
(1)
Possibility of putting in parallel with AD1083 connections.
(2)
Possibility of putting in parallel with comb type connection (not supplied).

5

System pro E power
spaces in between.
RANGE IDENTIFIER
System pro E power

C = Crosspieces 5
B = Busbar holder, Busbar, Brackets
T = Tie rods
R = Crosspieces, Tie rods

H = Busbar holder
F = Flat
S = Shaped
B = Busbar, Bottom
M = Metal
S = Stainless steel
B = Linear
S = Scaled
N = Nylon
C = Copper
V = Vertical
H = Horizontal
T = Top
MEASUREMENTS
The last 4 numbers usually refer to a measurement of the component or
several dimensions pertaining to the code.
P C R M 0 1 8 8

System pro E power
Order codes - Distribution systems
Crosspieces – Galvanzied sheet metal

Crosspieces in 20/10 thick hot-dip galvanized sheet metal, for < than 4000A current values. They are fixed directly
inside the cubicle using a purpose-made bracket to form busbar holders or as universal crosspieces.
Equipped with 12.5mm pitch rectangular holes, they are able to house insulating supports for thermoplastic busbar
holders with snap-fit mechanism.
Dimensions
structure
D W H Order ABB Package/
Description (mm) (mm) (mm) code code No.pcs
Depth galvanized sheet metal crosspieces for structures without intermediate upright
No.2 crosspieces 200 PCRM0188 1STQ007375A0000 1/2
5 No.2 crosspieces 700 PCRM0688 1STQ007380A0000 1/2

Depth galvanized sheet metal crosspieces for structures with intermediate upright or PCKI.... crosspieces
Width galvanized sheet metal crosspieces for structures with or without intermediate upright
Universal crosspieces
No.2 crosspieces L=2013mm PCRM2013 1STQ007391A0000 1/2
Closing galvanized sheet metal crosspieces with rear intermeiate upright
NEW Crosspieces total height
No.2 galvanized sheet metal
crosspieces for total height of 1800 PCRM1788 1STQ002007B0000 1/2
enclosures
No.2 galvanized sheet metal
crosspieces for total height of 2000 PCRM1988 1STQ002006B0000 1/2
enclosures

Crosspieces – AISI 304 stainless steel
Crosspieces in 25/10 thick AISI 304 stainless steel for ≥ than 4000A current values. They are fixed directly inside
the cubicle using a purpose-made bracket to form busbar holders or as universal crosspieces.
Equipped with 12.5mm pitch rectangular holes, they are able to house insulating supports for thermoplastic busbar
holders with snap-fit mechanism. Since the components are modular, the center distance between the phases can
be increased by spacing the insulating supports at a 12.5mm pitch.
Dimensions
structure
D W Order ABB Package/
Description (mm) (mm) code code No.pcs
Depth stainless steel crosspieces for structures without intermediate upright
No. 2 crosspieces 900 PCRS0888 1STQ007395A0000 1/2
Depth stainless steel crosspieces for structures with intermediate upright or PCKI.... crosspieces
No. 2 crosspieces 700 PCRS0438 1STQ007398A0000 1/2 5
Width stainless steel crosspieces for structures with or without intermediate upright
Closing stainless steel crosspieces
No. 2 crosspieces PCRS0338 1STQ007397A0000 1/2
No. 2 crosspieces PCRS0438 1STQ007398A0000 1/2
Universal crosspieces
No. 2 crosspieces L=2013mm PCRS2013 1/2
Flat copper busbars

Flat busbars Lenght =1750mm.
WxW No. Ø drilling Order ABB Package/

Description (mm) row drillings (mm) code code No.pcs
Flat copper busbar 20x5 1 6.5 PBFC2005 1STQ007401A0000 1/1
Flat copper busbar 40x10 - - PBFC4010 1STQ007410A0000 1/1

System pro E power
Flat busbars in Cuponal

Flat busbars in Cuponal (co-extruded copper-clad aluminium busbars) for In up to 3200A.
WxW Lenght Order ABB Package/
Description (mm) (mm) code code No.pcs
Flat busbars in Cuponal 20x5 1750 PBFA2005 1STQ009187A0000 1/1
5 Flat busbars in Cuponal 50x10 1750 PBFA5010 1STQ009195A0000 1/1
Shaped profile copper busbar

Shaped profile distribution busbars L=1750mm.
WxW Lenght Order ABB Package/

Description (mm) In (A) (mm) code code No.pcs
PBSC0400 Shaped copper 30x10 165 1750 PBSC0400 1STQ007418A0000 1/1
PBSC0630 busbar
Shaped copper 35x10 204 1750 PBSC0630 1STQ007419A0000 1/1
busbar
PBSC0800 busbar
busbar
busbar
PBSC1000
busbar
busbar
PBSC1600 Shaped copper 105x15 1255 1750 PBSC2500 1STQ007425A0000 1/1

PBSC1250 busbar
PBSC2000
PBSC2500

Connections D=300mm for not accessorized fixed breakers (front terminals)
LINEAR BUSBAR HOLDER, SHAPED BUSBARS 1600A IN CABLE CONTAINER
For horizontal fixed breakers 3 P is necessary to use the relating 3/4 P mounting kit in order to assemble the
connections. The busbar system must be build up with insulators W=50mm (PBHB1125). The busbars must be
mounted into the most rear and farther position from the circuit breaker with the neutral in the first position towards
the front. Use brackets PBBU008 for fixing the busbar system (see picture 2). The code includes an insulator
mounted on the plate (see picture 1).
Picture 1 Structure width (mm)
External Internal
cable cable
Circuit- No. container container Order ABB Package/
breakers poles In (A) W=300mm W=400mm code code No.pcs
Horizontal instllation
XT1 3P 160A 400 800 PBPX1631 1STQ009229A0000 1/1
XT1 3P 160A 600 1000 PBTX1631 1STQ009230A0000 1/1 5
XT1 4P 160A 400 800 PDPX1631 1STQ009231A0000 1/1
XT1 4P 160A 600 1000 PDTX1631 1STQ009232A0000 1/1
XT2 3P 160A 400 800 PBPX2631 1STQ009233A0000 1/1
XT2 3P 160A 600 1000 PBTX2631 1STQ009234A0000 1/1
XT2 4P 160A 400 800 PDPX2631 1STQ009235A0000 1/1
XT2 4P 160A 600 1000 PDTX2631 1STQ009236A0000 1/1
XT3 3P 250A 400 800 PBPX3631 1STQ009237A0000 1/1
XT3 3P 250A 600 1000 PBTX3631 1STQ009238A0000 1/1
XT3 4P 250A 400 800 PDPX3631 1STQ009239A0000 1/1
XT3 4P 250A 600 1000 PDTX3631 1STQ009240A0000 1/1
XT4 3P 250A 400 800 PBPX4631 1STQ009241A0000 1/1
Picture 2 XT4 3P 250A 600 1000 PBTX4631 1STQ009242A0000 1/1
XT4 4P 250A 400 800 PDPX4631 1STQ009243A0000 1/1
XT4 4P 250A 600 1000 PDTX4631 1STQ009244A0000 1/1
T4 3P 320A 400 800 PBPT4631 1STQ009245A0000 1/1
L1
T4 3P 320A 600 1000 PBTT4631 1STQ009246A0000 1/1
L2
T4 4P 320A 400 800 PDPT4631 1STQ009247A0000 1/1
L3
T4 4P 320A 600 1000 PDTT4631 1STQ009248A0000 1/1
N
T5 3P 400A 400 800 PBPT5631 1STQ009249A0000 1/1
T5 3P 400A 600 1000 PBTT5631 1STQ009250A0000 1/1
T5 4P 400A 400 800 PDPT5631 1STQ009251A0000 1/1
400mm
T5 4P 400A 600 1000 PDTT5631 1STQ009252A0000 1/1
T6 3P 800A 600 1000 PBTT6631 1STQ009253A0000 1/1
T6 4P 800A 600 1000 PDTT6631 1STQ009254A0000 1/1
350mm T7 3P 1600A 600 1000 PBTT7631 1STQ009255A0000 1/1
T7 4P 1600A 600 1000 PDTT7631 1STQ009256A0000 1/1
E1.2 3P 1600A 600 1000 PBTT7631 1STQ009255A0000 1/1
E1.2 4P 1600A 600 1000 PDTT7631 1STQ009256A0000 1/1
Vertical instllation
T6 (1) 3P 800A 600 1000 PCTT6631 1STQ009259A0000 1/1
T6 (1) 4P 800A 600 1000 PFTT6631 1STQ009260A0000 1/1
T7 (2) 3P 1600A 600 1000 PCTT7631 1STQ009261A0000 1/1
T7 (2) 4P 1600A 600 1000 PFTT7631 1STQ009262A0000 1/1
E1.2 (2) 3P 1600A 600 1000 PCTT7631 1STQ009261A0000 1/1
E1.2 (2) 4P 1600A 600 1000 PFTT7631 1STQ009262A0000 1/1
(1)
For vertical T6 breakers it is necessary to leave a blind cell above H=200mm.
For vertical T7 and E1.2 it is necessary to leave a blind cell above H=350mm. The connections are designed for the high side of
(2)
the circuit breakers with busbars to the right.

System pro E power
Connections D=300mm for not accessorized fixed breakers (front terminals)

LINEAR BUSBAR HOLDER, SHAPED BUSBARS 800A IN INTERNAL CABLE CONTAINER
W=200mm
For horizontal fixed breakers 3 P is necessary to use the relating 3/4 P mounting kit in order to assemble the connec-
tions. The busbar system must be build up with insulators W=50mm (PBHB1125). The busbars must be mounted
into the most rear and farther position from the circuit breaker with the neutral in the first position towards the front.
Use brackets PBBU008 for fixing the busbar system (see picture 2). The code includes an insulator mounted on
the plate (see picture 1).
Picture 1
No. Structure width Order ABB Package/
Circuit-breakers poles In (A) (mm) code code No.pcs
Horizontal instllation - Shaped busbars 800A
XT1 3P 160A 600 PBGX1738 1STQ008663A0000 1/1
XT1 3P 160A 800 PBPX1738 1STQ009265A0000 1/1
XT1 4P 160A 600 PDGX1738 1STQ008664A0000 1/1
5
XT1 4P 160A 800 PDPX1738 1STQ009266A0000 1/1
XT2 3P 160A 600 PBGX2738 1STQ008667A0000 1/1
XT2 3P 160A 800 PBPX2738 1STQ009267A0000 1/1
XT2 4P 160A 600 PDGX2738 1STQ008668A0000 1/1
XT2 4P 160A 800 PDPX2738 1STQ009268A0000 1/1
XT3 3P 250A 600 PBGX3738 1STQ008671A0000 1/1
XT3 3P 250A 800 PBPX3738 1STQ009269A0000 1/1
XT3 4P 250A 600 PDGX3738 1STQ008672A0000 1/1
XT3 4P 250A 800 PDPX3738 1STQ009270A0000 1/1
XT4 3P 250A 600 PBGX4738 1STQ008675A0000 1/1
XT4 3P 250A 800 PBPX4738 1STQ009271A0000 1/1
XT4 4P 250A 600 PDGX4738 1STQ008676A0000 1/1
Picture 2
XT4 4P 250A 800 PDPX4738 1STQ009272A0000 1/1
T4 3P 320A 600 PBGT4738 1STQ008679A0000 1/1
T4 3P 320A 800 PBPT4738 1STQ009273A0000 1/1
L1 T4 4P 320A 600 PDGT4738 1STQ008680A0000 1/1
L2 T4 4P 320A 800 PDPT4738 1STQ009274A0000 1/1
L3 T5 3P 400A 600 PBGT5738 1STQ008683A0000 1/1
N T5 3P 400A 800 PBPT5738 1STQ009275A0000 1/1
T5 4P 400A 600 PDGT5738 1STQ008684A0000 1/1
T5 4P 400A 800 PDPT5738 1STQ009276A0000 1/1
T6 3P 800A 800 PBPT6738 1STQ009277A0000 1/1
400mm T6 4P 800A 800 PDPT6738 1STQ009278A0000 1/1
Vertical instllation - Shaped busbars 800A
T6 (1) 3P 800A 800 PCPT6738 1STQ009279A0000 1/1
350mm T6
(1)
4P it is necessary
For(1)vertical T6 breakers 800A 800
to leave a blind cellPFPT6738 1STQ009280A0000
above H=200mm. 1/1
Insulator for connections

Order ABB Package/
Description code code No.pcs
Horizontal insulator for XT1-XT2-XT3-XT4-T4 PITH1234 1STQ001474B0000 1/1
Horizontal insulator for T5 PITH5000 1STQ001475B0000 1/1
Horizontal insulator for T6 PITH6000 1STQ001476B0000 1/1
Vertical insulator for T6 PITV6000 1STQ001477B0000 1/1
Horizontal/Vertical insulator for T7-E1.2 PITE7120 1STQ001478B0000 1/1

Insulating supports for busbars
10
Insulating supports for busbars in polyamide 6.6 with 30% fiberglass, equipped with shaped grooves for housing
busbars and pins for fixing to the crosspieces. Able to house both flat and shaped profile busbars.
PBHB1125 Dimensions Order ABB Package/

5 5
No.24 insulating supports for busbars 50 PBHB1125 1STQ007426A0000 1/24
10 10
PBHB2145
5 5 5 5
10 10 10
5
PBHB3121 NEW Scaled busbar holder

10 10
Scaled busbar holder for flat-shaped busbars complete with tie rods.
Order ABB Package/
PBHB1125 Description code code No.pcs
Scaled busbar holder PBHS1125 1STQ007429A0000 1/1
No.24 insulating supports for busbars PBHB1125 1STQ007426A0000 1/24
For 4 poles it is needed n. 8 insulators for each scaled busbar holder.
For 3 poles it is needed n. 6 insulators for each scaled busbar holder.
PBHS1125 PBHB1125 contains n. 24 insulators
PBBU0008
NEW Brackets for fixing vertical/horizontal busbars holder crosspieces
Order ABB Package/

No. 8 brackets for crosspieces PBBU0008 1STQ001588B0000 1/8
PBCB0002 NEW Brackets for fixing horizontal top/bottom busbars in corner structure
Order ABB Package/

No. 2 busbars backing brackets for corner structure PBCB0002 1STQ009186A0000 1/2
Nylon tie rods

Nylon tie rods (thermoplastic material for In <4000A current values).
Order ABB Package/

No.10 nylon tie rods L=195mm <4000A PTRN1951 1STQ007433A0000 1/10
Tie rods in AISI 304 stainless steel

Tie rods in AISI 304 stainless steel (for In ≥4000A current values).
Order ABB Package/
No. 10 Tie rods in AISI 304 stainless steel W=120mm PTRS1201 1STQ007434A0000 1/10

System pro E power
Brackets for earth and neutral fixing
Order ABB Package/

N No. 2 brackets for earth fixing PBRP0002 1STQ001554B0000 1/2
PBRP0002 PBRN0002 No. 2 brackets for neutral fixing PBRN0002 1STQ001555B0000 1/2
Crosspiece fixing brackets - vertical/horizontal
Order ABB Package/

No. 8 brackets for crosspieces PBBV0008 1STQ007430A0000 1/8
5 PBBV0008 PBBT0008 No. 8 brackets for crosspieces PBBV0008 1STQ007432A0000 1/8
PCKI.... Crosspiece for horizontal busbar assembly under top or on bottom of structure
PCKI.... For assembly in D>300mm structures with internal cable compartment, order PCCM.... cable compartment depth
PCCM.... crosspieces as well.
PCCS....
Intermediate crosspiece for busbars under
300 PCKI0300 1STQ008099A0000 1/1
top/on bottom
400 PCKI0400 1STQ008100A0000 1/1
top/on bottom
600 PCKI0600 1STQ008101A0000 1/1
top/on bottom
800 PCKI0800 1STQ008102A0000 1/1
top/on bottom
1000 PCKI1000 1STQ008103A0000 1/1
top/on bottom
1250 PCKI1250 1STQ008104A0000 1/1
top/on bottom
PFCB4080 Compensators and connections for flat and shaped busbar

PFCB1016
PFCB2025 Order ABB Package/
Connections between shaped busbar/shaped busbar
PFCB4080 1STQ009224A0000 1/1
or shaped busbar/flat busbar for 400A, 630A, 800A
or shaped busbar/flat busbar for 1000A, 1250A, PFCB1016 1STQ009225A0000 1/1
1600A
PFCC0023
PFCB2025 1STQ009226A0000 1/1
or shaped busbar/flat busbar for 2000A, 2500A
Compensator for configurations compose of no. of
PFCC0023 1STQ009227A0000 1/1
busbar per phase>1

PBUF002
Unifix H
Description (mm) W code code No. pcs
No.2 brackets for fixing Unifix to structure PBUF0002 1STQ008117A0000 1/2
Frames for Tmax and modular circuit-breakers - System pro M
Frames with 24 busbars DIN
600 ED2183 1STQ008228A0000 1/1
modules
Frames with 36 busbars DIN
800 ED2191 1STQ008229A0000 1/1
ED2209 modules
Feeder modules
4P 400A feeder module (for ED2183-ED2191) ED2209 1STQ008230A0000 1/1
Basic module In 16A
Basic module for auxiliaries DIN L1-N high 16A ED2894 1STQ008255A0000 1/1
ED2894 Basic module for auxiliaries DIN L1-L2 high 16A ED2902 1STQ008256A0000 1/1
ED2902
Basic module for auxiliaries DIN L1-N low 16A ED2910 1STQ008257A0000 1/1 5
Basic module for auxiliaries DIN L1-L2 low 16A ED2928 1STQ008258A0000 1/1
ED2910
ED2928 Basic module In 40A
Basic module L1/Neutral high 40A ED2654 1STQ008248A0000 1/1
ED2654
ED2662 Basic module In 63A
ED2670 Basic module L1 high 63A ED2531 1STQ008231A0000 1/1
ED0004 Basic module L2 high 63A ED2549 1STQ008232A0000 1/1
ED2531-ED2549
Basic module L3 high 63A ED2556 1STQ008238A0000 1/1
ED2564-ED2556 Basic module Neutral high 63A ED2564 1STQ008243A0000 1/1
Basic module L1 low 63A ED2572 1STQ008244A0000 1/1
Basic module Neutral low 63A ED2606 1STQ008247A0000 1/1
ED2720-ED2738 Basic module In 100A
ED2746-ED2753
ED2551-ED2552 Basic module with cable L1 high 100A ED2720 1STQ008251A0000 1/1
ED2553-ED2554
Basic module with cable L2 high 100A ED2738 1STQ008252A0000 1/1
Basic module with cable L3 high 100A ED2746 1STQ008253A0000 1/1
Basic module with Neutral cable high 100A ED2753 1STQ008254A0000 1/1
Basic modules ≤ In 40A S800
Basic module L1 high ≤40A ED2557 1STQ008239A0000 1/1
ED2845 Basic module Neutral high ≤40A ED2560 1STQ008242A0000 1/1
ED2550
Basic modules ≤ In 125A S800
Basic module Neutral high 125A ED2554 1STQ008237A0000 1/1
Basic module pole blank L=27mm ED2550 1STQ008233A0000 1/1
ED2572-ED2590
ED2598-ED2506

System pro E power
Unifix H
ED2217-ED2225
ED2233-ED2241 Order ABB Package/
ED2258-ED2266 Description code code No. pcs
ED2274-ED2282
ED2332-ED2340
ED2357-ED2365 Basic modules ≤ In 160A Tmax XT1 (front terminals FCCuAl)
Basic module L1 high L2 low ED2217 1STQ008263A0000 1/1
Basic module L3 high Neutral low ED2233 1STQ008265A0000 1/1
Basic module Neutral high L3 low ED2241 1STQ008266A0000 1/1
Basic module pole blank for RC221 residual current ED2373 1STQ008279A0000 1/1
release
Basic module pole blank for solenoid operating ED2381 1STQ008280A0000 1/1
ED0001 mechanism
ED0002
ED0003 Basic modules ≤ In 160A Tmax T2
5 ED2290-ED2308 Basic module L1 high L2 low ED2258 1STQ008267A0000 1/1
ED2316-ED2324
Basic module L3 high N low ED2274 1STQ008269A0000 1/1
Basic module N high L3 low ED2282 1STQ008270A0000 1/1
release
Basic module pole blank for solenoid operating ED2399 1STQ008281A0000 1/1
mechanism
Basic modules ≤ In 250A Tmax XT3
ED2373 Basic module L1 high ED2290 1STQ008271A0000 1/1
ED2381 Basic module L2 high ED2308 1STQ008272A0000 1/1
ED2399
Basic module L3 high ED2316 1STQ008273A0000 1/1
Basic module N high ED2324 1STQ008274A0000 1/1
Basic module L1 low ED2332 1STQ008275A0000 1/1
Basic module N low ED2365 1STQ008278A0000 1/1
release
ED2407 Accessories
PPMU3060 Basic module pole blank for DDA W=17.5mm ED2845 1STQ008283A0000 1/1
PPMU3080
Basic module pole blank for MDRC modular units ED2852 1STQ008284A0000 1/1
2 IP20 covers (for ED2183-ED2191) ED2407 1STQ008282A0000 1/2
W=173mm (10 DIN mod.)
6 duct supports 40x60mm ED2936 1STQ008285A0000 1/6
(only with modular apparatus)
Modular front panel 300x600mm (HxW) PPMU3060 1STQ008299A0000 1/1
ED2936
Modular front panel 300x800mm (HxW) PPMU3080 1STQ008300A0000 1/1
Spare parts
10 terminal covers for T1 ED0001 1STQ008259A0000 1/10
10 terminal covers for S200/F200 ED0004 1STQ008262A0000 1/10

2 poles 4 poles Unifix L
N L1 N L1 L2 L3
2 brackets for fixing Unifix to structure PBUF0002 1STQ008117A0000 1/2
2-pole busbars
100A 2P busbar 8 modules 200 ED2985 1STQ008313A0000 1/6
ED3066 100A 2P busbar 12 modules 400 ED2993 1STQ008314A0000 1/6
ED3058
4-pole busbars
5
Connections for various equipment
ED3104
Connection with 2 conductors L1/N 16A ED3108 1STQ008332A0000 1/6
ED3101
ED3102 Connection with 3 conductors L1/L2/L3 16A ED3116 1STQ008333A0000 1/6
ED3103 Connection with 4 conductors L1/L2/L3/ 16A
ED3124 1STQ008334A0000 1/6
single-phase
Connection with 2 conductors L1/N 40A ED3355 1STQ008339A0000 1/6
Connection with 3 conductors L1/L2/L3 40A ED3363 1STQ008340A0000 1/6
Connection with 4 conductors L1/L2/L3/N 40A ED3371 1STQ008341A0000 1/6
Connections for apparatuses
Connections L1-N 40 A ED3272 1STQ008336A0000 1/10
Connections L 1 100A ED3033 1STQ008318A0000 1/10
Connections L 2 100A ED3041 1STQ008319A0000 1/10
400 350
600 1500 Connections L 3 100A ED3058 1STQ008320A0000 1/10
800 2500
1500 Connections N 100A ED3066 1STQ008321A0000 1/10
Feeder with cable 4P 100A (L=350mm) ED3132 1STQ008335A0000 1/10
Feeder module with cable
2P 100A parallel module with cable (L=600mm) ED3082 1STQ008322A0000 1/6
ED3090 ED3132 ED3124 4P 100A parallel module with cable (L=800mm) ED3413 1STQ008343A0000 1/6
ED3405 ED0026
ED3413 ED0025 4P 100A parallel module with cable (L=1500mm) ED3439 1STQ008344A0000 1/6
ED3439
Feeder module without cable In 100A
Single-pole feeder modules L 1 ED3101 1STQ008324A0000 1/10
Single-pole feeder modules N ED3104 1STQ008330A0000 1/10
Accessories
10 busbar covers (L=600mm) ED2961 1STQ008309A0000 1/10
2 busbar covers (L=800mm) ED2962 1STQ008310A0000 1/2

System pro E power
Order codes - Accessories
Rack rails in painted Sendzimir steel wire L=3000mm

Order ABB Pack./me-
Description code code ters
H=35mm
Basic straight rack rails 75mm 1SL9816A00 1SL9816A00 24
H=50mm
5 Basic straight rack rails 150mm 1SL9838A00 1SL9838A00 24
H=75mm
Straight separator profiles in Sendzimir

Order ABB Package/
L 2000mm separator profiles for rack rails H 35mm 1SL9904A00 1SL9904A00 1/20
L 2000mm separator profiles for rack rails H 50mm 06652 06652 1/20
L 2000mm separator profiles for rack rails H 75mm 07855 07855 1/20

Covers in Sendzimir L=3000mm
Order ABB Pack./me-

Description code code ters
Basic straight cover 75mm 07241 07241 24
5
1SL9907A00-1SL9886A0
1SL9887A000
Accessories in Sendzimir
Order ABB Package/
Linear coupling 1SL9880A00 1SL9880A00 1/2
Linear snap-fit coupling for rack rails H 35mm 1SL9907A00 1SL9907A00 1/2
1SL9910A00÷1SL9915A00
Bracket fixing element complete with screws 1SL9893A00 1SL9893A00 1/10
L 150mm crosspiece for rack rails B 75-100mm 1SL9910A00 1SL9910A00 1/10
L 200mm crosspiece for rack rails B 150mm 1SL9911A00 1SL9911A00 1/10
1SL9893A00 L 350mm crosspiece for rack rails B 300mm 1SL9913A00 1SL9913A00 1/10
Note: The steel wire racks are also available in the following versions: unpainted Sendzimir; electrogalvanized; hot-dip galvanized
after machining.

System pro E power
5 20 6MA
Earthing copper busbars
20
Flat busbar, drilled and threated for earthing.
ABB Codice Package/

5 20 6MA Description code ABB No.pcs
No. 2 drilled and threaded busbars 20x5mm
25
EV1119 1STQ001014A0000 1/2

L=2000mm
EV1120 1STQ001015A0000 1/2
6MA
L=2000mm
5 25
EV1121 1STQ001016A0000 1/2
50
L=2000mm
Insulators
5
ABB Codice Package/
Description code ABB No.pcs
EV1122-EV1123
No.50 hexagonal insulators 30x30mm M6 EV1122 1STQ001017A0000 1/50
EV1124-EV1125
EV1051
Sliding aluminium rails for general purposes
EV1056 ABB Codice Package/
EV1058 Description code ABB No.pcs
EV1050 No. 10 aluminium sectionso 30x15x1,8 - L=2000mm EV1050 1STQ000981A0000 1/10
No. 25 fixing brackets for EV1050 EV1051 1STQ000982A0000 1/25
No. 100 M6 aluminium nuts for EV1050 EV1056 1STQ000983A0000 1/100
No. 100 M8 aluminium nuts for EV1050 EV1058 1STQ000984A0000 1/100
EV1090 Brackets for anchoring cables

EV1091
EV1092 Adjustable cable clamping bracket. Can be mounted on sections with 10mm slot EV1050.
EV1093
ABB Codice Package/
Description code ABB No.pcs
No.10 cable clamping brackets Ø9÷16mm min÷max EV1090 1STQ000999A0000 1/10
No.10 cable clamping brackets Ø16÷30mm EV1091 1STQ001000A0000 1/10
EV1050 min÷max

AD1066
Angled supports for terminal boxes and earthing busbars

EV1110 Order ABB Package/
No.50 angled supports 1 row of terminals EV1110 1STQ001007A0000 1/50
AD1065 AD1067 EV1113
AD1069
AD1068 5
Profiles for accessories
Universal profiles of different types for mounting any component or for cable locking.
Dimensions
TS4013 TS4011 TS4012
Description L code code No.pcs
AD1063 No. 2 EN sections 5002 C30 2000 TS4011 1STQ008211A0000 1/2
No. 2 EN sections G32 2000 TS4012 1STQ008212A0000 1/2
No. 2 DIN EN sections 5022 35x7.5 2000 TS4013 1STQ008213A0000 1/2
TS4000-TS4001-TS4002
TS4003-TS4004
20
AD1056 Hammer-head screws for shaped profile busbars
Order ABB Package/
AD1078 code code
Description No.pcs
27
AD1064
No.12 screws M8 - L=20mm for cable terminals AD1056 1STQ008214A0000 1/12
No.12screws M8 - L=27mm for plates up to 10mm,
AD1064 1STQ008215A0000 1/12
complete with screw cap
37
AD1071 No.12 screws M8 - L=37mm for plates up to 20mm,
AD1071 1STQ008216A0000 1/12
No.12 screws M8 - L=47mm for plates up to 30mm,
47 AD1072
BA2000 AD1072 1STQ008217A0000 1/12
AD1073
BA2000
Couplings for shaped profile busbars

Order ABB Package/
AD1077
No.4 400A branch connectors in copper AD1077 1STQ008218A0000 1/4

Fig. 6
System pro E power

Busbar clamps
Kit for clamping flexible busbars to rigid busbars without forcing the flexible busbars.
Order ABB Package/

2 pairs of fixing plates for busbars H=40mm BS3250 1STQ008219A0000 1/4
Barre flessibili
Barre flessibili isolate in materiale autoestinguente.
5 Dimensions
(mm)
WxW Order ABB Package/
Description (mm) L In (A) code code No. pcs
No.2 flexible busbars 15.5x3.2 2000 160 PBFC0160 1STQ009175A0000 1/2
No.2 flexible busbars 20x3 2000 250 BF1602 1STQ008222A0000 1/2
No.2 flexible busbars 32x5 2000 630 BF4012 (1)
1STQ008225A0000 1/2
(1)
Only for circuit-breakers with extended front connections or rear connections.
Lateral connection module for terminal ditching

Lateral drilled module 25mm pitch for fixing the crosspieces with insulating supports in width from the intermediate
upright up to the rear structural upright. In order to complete the terminals ditching it is necessary to fix sideways
the two connection modules included in the code. The crosspieces PCRM .... or PCRS .... is fixed using the spe-
cial fixing brackets for module connection PBMC0002. The crosspiece is to be chosen and ordered separately
according to the width of the structure.
H D Order ABB Package/
Description (mm) (mm) code code No. pcs
PCRM.... No.2 lateral connection modules 175 500 PMCS1755 1STQ009200A0000 1/2
PCRS....
No.2 lateral connection modules 200 500 PMCS2050 1STQ009201A0000 1/2
PBMC0002 No.2 lateral connection modules 175 700 PMCS1757 1STQ009205A0000 1/2
No.2 fixing brackets connection module PBMC0002 1STQ009215A0000 1/2

Splitters
Order ABB Package/
Unipolari
AD1080 AD1081 AD1030 Modular 125A AD1076 (1) 1STQ008287A0000 1/1
AD1031
Modular 125A AD1080 (2)
1STQ008288A0000 1/1
Modular 175A AD1007 (1) 1STQ008293A0000 1/1
Modular 175A AD1081 (2) 1STQ008289A0000 1/1
Modular 250A AD1030 1STQ008297A0000 1/1
Modular 125A AD1031 1STQ008298A0000 1/1
Threepole
AD1075 AD1004
AD1006 Modular 125A AD1075 1STQ008286A0000 1/1
Modular 175A AD1006 1STQ008292A0000 1/1
5
Four-pole
Modular 125A AD1004 1STQ008291A0000 1/1
Modular 125A-medium-93x89x48 (HxLxD) AD1028 1STQ008295A0000 1/1
Modular 125A-large-96x126x48 (HxLxD) AD1029 1STQ008296A0000 1/1
AD1028 AD1027 Modular 160A AD1027 1STQ008294A0000 1/1
AD1029
250A horizontal for L=600mm structures AD1034 1STQ008345A0000 1/1
250A horizontal for L=800mm structures AD1053 1STQ008346A0000 1/1
No.2 fixing brackets for AD1034-AD1053 PBRF3453 1STQ009184A0000 1/2

(1)
10 outputs - (2) 6 outputs
AD1034
AD1053
Assembly accessories
Order ABB Package/
Joining accessory for two AD1080 AD1083 1STQ008290A0000 1/1
N N N
Labels
N NL1 NL1
L1
N NL1 N
LL11
LL11 Order ABB Package/
L1 LL1 L1 L L2
L2 L11LLL11 LL11 Description code code No. pcs
L2 L2 LL11 2 L3
L2 T2 L3
L3 No.490 ø12mm adhesive labels with N symbol EV1150 1STQ001033A0000 1/490
No.490 ø12mm adhesive labels with L1 symbol EV1151 1STQ001034A0000 1/490
No.490 ø12mm adhesive labels with T symbol EV1154 1STQ001037A0000 1/490
400 VOLT
No.10 triangular 125mm adhesive labels with 400V EV1155 1STQ001038A0000 1/10
lightning flash symbol
No.300 triangular 20mm adhesive labels with light- EV1156 1STQ001039A0000 1/300
ning flash symbol

System pro E power
Segregations
General information
Segregations in accordance with Standard IEC 61439-1-2 6/2
Internal segregation kits 6/3
Segregation Form 2a - 3a 6/4
Segregation Form 2b 6/6
Choice of segregation 7/12
Order code
Form 2a - 3a 6/22
Segregations busbars Form 2b - 3b - 4b 6/26
Form 3b 6/32
Form 4b 6/46
6

System pro E power
General information
Segregations in accordance with Standard IEC 61439-1-2

Segregation form means the type of division inside the switchboard. Segregation by means of metal or insulating barriers or partitions
may be required to:
- Provide protection against direct contacts (at least IPXXB) when a de-energized part of a switchboard must be accessed while the rest
of it remains energized.
- Reduce the possibility of internal arc ignition and propagation.
- Prevent solid bodies from passing between different parts of the switchboard (protection class at least IP2X).
Partition means the element that separates two compartments while the barrier protects the operator from direct contact and from the
effects of the arc of a switching device in the usual direction of access. The partition can also be a casing that is an integral part of an
apparatus, e.g. a moulded-case circuit-breaker.
Symbols Form 1 Form 2 Form 3 Form 4

No internal segregation Segregation of busbars from all Segregation of busbars from all Segregation of busbars from all
functional units functional units. functional units.
-Segregation of all functional units -Segregation of all functional units
from each other from each other
6 -Segregation of the terminals for -Segregation of the terminals for
external conductors and the external external conductors associated with
conductors from the functional units, a functional unit from the terminals
but not from the terminals of other of any other functional unit and from
a b d functional units the busbars
-Segregation of the external conduc-
tors from the busbars
-Segregation of the external conduc-
tors associated with a functional unit
from other functional units and their
terminals
c
-The external conductors do not
need to be separated from each
other
Form 2a Form 3a Form 4a

The terminals for external conduc- The terminals for external conduc- The terminals for external conduc-
tors are not separated from the tors are not separated from the tors are in the same compartment as
busbars busbars associated functional unit
Form 2b Form 3b Form 4b

The terminals for external conduc- The terminals for external conduc- The terminals for external conduc-
tors are separated from the busbars tors and the external conductors are tors are not in the same compart-
separated from the busbars ment as associated functional unit
but are in individual spaces or
compartments, separated, enclosed
and protected
Key
a Empty enclosure
b Internal segregation
c Functional unit, including the terminals for the associated external
conductors
d Busbars, including the distribution busbars

Internal segregation kits
The different segregation Forms, (Form 2a, 2b, 3a and 4b), that can be created in the new System pro E power main distribution
switchboard are described in the following pages.
The descriptions include the following inFormation for each segregation Form:
- the basic conditions for its creation
- the various solutions
- the reference tables for the choice of codes
Generally speaking, the basic segregation Form of the circuit-breaker kits (Form 1) passes to Form 4b by adding different accessories in
sequence, depending on the case in question.
The main innovation introduced by the new System pro E power segregation system concerns the kits for circuit-breakers with front
(with high terminals*) and rear terminals for Form 2b.
The segregation Form 2a - 3a, 3b and 4b can be reached with front terminals (with high terminal covers*) or rear terminals only
for fixed circuit-breakers. With plug-in or withdrawable circuit-breakers the segregations can be built up with rear terminals.
Using side by side moulded case circuit-breakers and moulded case circuit brackers with recessed mounting plate** the
highest segregation form reachable is Form 3a. The side by side air circuit-breakers are not segregated. 6
The segregations mainly consist of horizontal or vertical shelves at the front or rear in relation to the intermediate upright, or throughout
the width/depth of structures without the intermediate upright.
The intermediate upright is required for all segregation Forms differing from Form 2b, even when not needed by the circuit-
breaker version.
Segregation Forma 2a - 3a, designed for structures with D≥500mm, is created with side closing elements for the compartment and
universal horizontal shelves to install between kits with different depths (D≥38mm), and above and below the kit compositions (top
and bottom). With IP3X protection degree and cable compartment internal door it is necessary to install a vertical segregation and the
intermediate upright (1 pcs. for internal cable container, 2 pcs. for external cable container). With IP65/IP4X and cable compartment
internal door it is not necessary any further segregation. Blind compartments are specially created to fill the empty spaces inside the
structure, while there are special closing segregations for DIN rails. The blind compartments are not suitable for fixing accessories.
Install a blind bottom plate and panel if required. If the blind compartment is mounted in the first or in the last position into a column, the
universal horizontal shelves cannot be mounted at the top or at the bottom.
Where the terminals are separated by the busbars, segregation Form 2b can be obtained by a combination of pre-cut or blind
H=800/1000mm side walls that cover the structure at the side along its entire height and with horizontal and vertical shelves for busbar
segregation in structures with or without intermediate upright, for external and internal cable compartments.
Some vertical walls are pre-cut so as to accommodate the busbars. To guarantee protection class IP=20, they have TPV rubber seals
that adhere perfectly to the removed parts. If the column requires the installation of intermediate uprights, the cable container shall
have the intermediate upright (1 pcs. for internal cable container, 2 pcs. for external cable container). If the column does not require the
installation of intermediate uprights, no intermediate uprights have to be mounted into the cable container.
Segregation Form 3b is obtained by segregating the busbars from all the functional units, adding dedicated accessories for the
installation of horizontal or vertical circuit-breakers. The horizontal circuit-breakers are segregated by means of sliding vertical rear
separators that divide the input and output terminals, while the vertical circuit-breakers have a modular horizontal separator. The busbar
side is segregated by panels fixed to the sides and bottom of the structure between the uprights.
In case of segregation Form 3b, vertical breakers can be installed in the first available position under the top of the structure (top) or the
last available position in the structure (bottom), with a maximum of two vertical breakers per column.
Segregation Form 4b is obtained for horizontal circuit-breakers by means of cubicles that completely isolate the circuit-breaker
terminals. The rear part of the segregation is created by a Lexan panel fixed with a dedicated bshelfet and shelves, depending on
the depth of the circuit-breaker. Form 4b is obtained for vertical circuit-breakers by duplicating the codes of the vertical bottom
segregations and vertical side segregations used for Form 3b, closing the circuit-breaker compartment and installing an additional
vertical side segregation on the output side.
In Form 3b and Form 4b the intermediate upright is always mandatory (1 pcs. for internal cable container, 2 pcs. for external cable
container).
* High terminal covers are available for all Tmax T/XT fixed and Emax E1.2 fixed, except for XT1, XT3 F-RC and kit PHBX3301, PHBX3401, PHBX4301, PHBX4401, PHBT4301, PHBT4406, PHBT5306,
PHBT5406 and Tmax T6/T7 withdrawable and plug-in versions. For Tmax XT1/XT2/XT3/XT4 withdrawable and plug-in versions it is necessary to order the dedicated adapter covers for terminals. For Tmax
T4/T5 withdrawable and plug-in versions it is necessary to order the dedicated high terminal covers for 3 or 4 poles.
** See page 8/10.
System pro E power
General information
Segregation Form 2a - 3a
Universal compartment side closing

element
PPVS....
Universal horizontal shelf

PSHS....

Examples of busbar use in the structure
Structures with intermediate upright
To obtain segregation Form 2a - 3a, use universal compartment side closing elements PPVS... and universal horizontal shelves PSHS....
under the top and on the bottom, and whenever consecutive compartments contain circuit-breakers with D ≥ 38mm difference in depth.
Horizontal circuit-breaker with front Vertical circuit-breaker with front terminals 6

terminals
Horizontal circuit-breaker with rear Vertical circuit-breaker with rear terminals

terminals
Horizontal circuit-breaker with front/rear

terminals
High terminal covers are available for all Tmax T/XT fixed and Emax E1.2 fixed, except for XT1, XT3 F-RC and kit PHBX3301, PHBX3401, PHBX4301, PHBX4401, PHBT4301, PHBT4406, PHBT5306,
PHBT5406 and Tmax T6/T7 withdrawable and plug-in versions. For Tmax XT1/XT2/XT3/XT4 withdrawable and plug-in versions it is necessary to order the dedicated adapter covers for terminals. For
Tmax T4/T5 withdrawable and plug-in versions it is necessary to order the dedicated high terminal covers for 3 or 4 poles.

System pro E power
General information
Segregation Form 2b
PTVB...
Blind side segregation for column
PFVS... vertical busbar shelves
PTVS... Precut side segregation for column
PTHS... horizontal busbar shelves

Examples of busbar use in the cable compartment
To obtain segregation Form 2b, use dedicated horizontal shelves PTHS.... and front segregations PFVS.... for the structure, internal
cable compartment and external cable compartment. The busbars are segregated with precut PTVS... or blind PTVB... side segregations
for columns, which can be full-depth for structures without intermediate uprights and divided into front and rear for structures with
intermediate uprights. Terminal covers to be ordered with the circuit-breakers must be used for circuit-breakers with front terminals.
Structures without intermediate upright Structures with intermediate upright
Horizontal circuit-breaker with front Horizontal circuit-breaker with front Vertical circuit-breaker with front
terminals rear outputs terminals rear outputs terminals 6
Horizontal circuit-breaker with front Horizontal circuit-breaker with front Vertical circuit-breaker with rear
terminals side outputs terminals side outputs terminals

terminals

terminals

System pro E power
General information
Segregation Form 3b
6
PSVS... Segregation for horizontal
circuit-breaker
PSVS...1 Segregation for busbar side of

horizontal circuit-breakers
PSHS... Universal horizontal shelf
PLVS... Vertical side segregation of

horizontal circuit-breaker compartment
PPVS... Universal compartment side

closing element

3b segregation begins with the components used for Form 2a - 3a with the addition of elements to separate the circuit-breaker
terminals: for horizontal circuit-breakers this is obtained by means of sliding plate PSVS... while for vertical circuit-breakers, a precut
shelf, PSHS..., is used for the passage of busbars. The busbar side must be isolated at the rear with PRVS...1 busbar side segregations
and at the sides, with PLVS... side segregations. In case of segregation Form 3b, vertical breakers can be installed in the first available
position under the top of the structure (top) or the last available position in the structure (bottom), with a maximum of two vertical
breakers per column.
Horizontal circuit-breaker with front Vertical circuit-breaker with front terminals Vertical circuit-breaker with front terminals
terminals with rear intermediate upright*
Horizontal circuit-breaker with rear Vertical circuit-breaker with rear terminals Vertical circuit-breaker with rear terminals
terminals with rear intermediate upright*

terminals
* The rear intermediate upright is used when with the vertical breaker also an
horizontal breaker is installed in the same column.

System pro E power
General information
Segregation Form 4b
PCVS...
Output closing cubicles, to create
according to the depth and type of
circuit-breaker
6
PSVS...
Segregation for horizontal circuit-breaker
PSVS...1 Segregation for busbar side of

horizontal circuit-breakers
PSHS... Universal horizontal shelf
PLVS... Vertical side segregation of

horizontal circuit-breaker compartment
PPVS...
Universal compartment side closing
element

4b segregation begins with the components used for Form 2a - 3a - 3b. It is obtained by means of dedicated PCVS... cubicles chosen
to suit the depth of the circuit-breaker, and horizontal shelves PSHS... required for each depth change of the output closing cucibles in
the same column. Use universal vertical shelf PSHS.... for each compartment in order to reach Form 4b.
Horizontal circuit-breaker with front terminals

6
Horizontal circuit-breaker with rear terminals

terminals
Horizontal circuit-breaker with front terminals


System pro E power
General information
Choice of segregation to suit height of kits

Tmax T and Tmax XT moulded-case circuit-breakers
Horizontal installation
Form 2a Form 3a (2) Form 3b

Universal horizontal Vertical segregation Rear vertical bottom
shelf of terminals segregation on busbar side
Universal
6 compartment Depth of structure (mm)
Height side closing Width of struc- For all Width of struc- Width of struc- For all
of kits (mm) element ture (mm) depths ture (mm) 500 700 900 ture (mm) depths
200 PPVS2200 400 PSHS1904 400 PSVS2050 PSVS2070 PSVS2090 400 PRVS2041
600 PSHS1906 600 PSVS2050 PSVS2070 PSVS2090 600 PRVS2061
1000 PSHS1901 1000 PSVS3050 PSVS3070 PSVS3090 1000
600 (1) PSHS1906 600 PSVS4050 PSVS4070 PSVS4090 600 PRVS4061
1000 PSHS1901 1000 PSVS5050 PSVS5070 PSVS5090 1000
700 PPVS2700 600 PSHS1906
(1)
Also for fixed/interlocked horizontal Emax 2 E1.2 for W=600mm and W=800mm.
(2)
To install only between kits with different depths (D≥38mm) and above and below the kit compositions (top and bottom).
(3)
For T7 withdrawable and withdrawable interloked use the segregations for horizontal E1.2 withdrawable for W=600mm and W=800mm.

For the cubicles assembly position please refer to page 6/46 taking into
consideration the breakers type.
P0 P1 P2
Form 4b
Side vertical Cubicles to suit depth of
segregation (3) circuit-breaker
Depth of structure (mm) Assembly position 6
Width
of structure (mm) 500 700 900 P0 P1 P2
400 PLVS2052 PLVS2072 PLVS2092 PCVS0204 PCVS1204 PCVS2204
1000
1000
(3)
Only required when columns are installed side by side, to separate the cable area and busbar area.

System pro E power
General information
Choice of segregation to suit height of kits

Tmax T and Tmax XT moulded-case circuit-breakers
Vertical installation
Form 2a Form 3a (2) Form 3b

Universal horizontal Horizontal segregation Rear vertical bottom
shelf of terminals segregation on busbar side
6 Universal Depth of structure (mm) Width
Height compartment Width of struc- For all of structure For all
of kits (mm) side closing element ture (mm) depths 500 700 900 (mm) depths
200 PPVS2200 400 PSHS1904 PSHS4050 PSHS4070 PSHS4090 400
600 PSHS1906 PSHS6050 PSHS6070 PSHS6090 600
1000 PSHS1901 1000
300 PPVS2300 400 PSHS1904 PSHS4050 PSHS4070 PSHS4090 400
1000 PSHS1901 1000
350 PPVS2350 400 PSHS1904 PSHS4050 PSHS4070 PSHS4090 400 PRVS1741
600 PSHS1906 PSHS6050 PSHS6070 PSHS6090 600 PRVS1761
1000 PSHS1901 1000
1000 PSHS1901 1000
450 PPVS2450 400 (1) PSHS1904 PSHS4050 PSHS4070 PSHS4090 400 PRVS2241
600 (1) PSHS1906 PSHS6050 PSHS6070 PSHS6090 600 PRVS2261
1000 PSHS1901 1000
1000 PSHS1901 1000
1000 PSHS1901 1000
1250 1250
(1)
Also for fixed/interlocked vertical Emax 2 E1.2 for L=400mm, L=600mm and L=800mm.
(2)
To install only between kits with different depths (D≥38mm) and above and below the kit compositions (top and bottom).
(3)
For T7 withdrawable and withdrawable interloked use the segregations for vertical E1.2 withdrawable for W=600mm and W=800mm.

Form 4b
Form 4b is obtained by duplicating the codes of vertical bottom segregations PRVS... and
vertical side segregations PLVS..., closing the circuit-breaker compartments over the
entire height of the switchboard and installing an additional vertical side segregation on
the output side.
As an alternative to the PLVS... vertical

side segregations, in the case of main
circuit-breakers (Tmax T5, T6, T7), use
the PMCS... side connection module for
fixing terminal extensions and the relative
fixing bshelfets PBMC0002 (page 4/40).
Vertical bottom Full width vertical bottom Vertical side

segregation on busbar side segregation segregation
Width Depth of structure (mm) 6

of structure For all Width For all
(mm) depths of structure (mm) depths 500 700 900
400 400
600 600
800 800
1000 1000
400 400
600 600
800 800
1000 1000
400 400 PRVS1740 PLVS1752 PLVS1772 PLVS1792
600 PRVS1762 600 PRVS1760 PLVS1752 PLVS1772 PLVS1792
400 400 PLVS2552 PLVS2572 PLVS2592
1250 1250 PRVS3125

System pro E power
General information
Choice of segregation
Emax 2 air circuit-breakers *
E1.2 withdrawable - E2.2 - E4.2 - E6.2 vertical E1.2 withdrawable - E2.2 - E4.2 - E6.2 verical
Vertical fixed Emax 2

6 Form 2a-3a Form 3b
Segregation kit Horizontal terminal separator
E2.2 E4.2 E6.2 E2.2 E2.2 E4.2 E4.2 E6.2

Height of kits (mm) Depth (mm)
Width of
Width of Kit/ Kit/column
column (mm) 600 600 700 (mm) 700 900 700 900 900
600 PSVF6062 PSVF6064 600 PSHF6072 PSHF6092 PSHF6072 PSHF6092
800 PSVF6082 PSVF6084 800 PSHF8072 PSHF8092 PSHF8072 PSHF8092
1000 PSVF7016 1000 PSHF1096
1250 PSVF7126 1250 PSHF1296
Vertical withdrawable Emax 2

Form 2a-3a Form 3b
Segregation kit Horizontal terminal separator
E1.2 E2.2 E4.2 E6.2 Width of E1.2 E1.2 E1.2 E2.2 E2.2 E4.2 E4.2 E6.2
Width of Kit/
Kit/column column
(mm) 500 600 600 700 (mm) 500 700 900 700 900 700 900 900
600 PSVW5061(1) PSVW6062 PSVW6064 600 PSHW6051(1) PSHW6071(1) PSHW6091 PSHW6072 PSHW6092 PSHW6074 PSHW6094
800 PSVW5081(1) PSVW6082 PSVW6084 800 PSHW8051(1) PSHW8071(1) PSHW8091 PSHW8072 PSHW8092 PSHW8074 PSHW8094
1000 PSVW7016 1000 PSHW1096
1250 PSVW7126 1250 PSHW1296
Horizontal withdrawable Emax 2 Form 2a-3a Form 3b-4b

Form 2a-3a Form 3b Form 4b
Segregation kit Vertical terminal separator Rear cubicle E1.2 horizontal
E1.2 E1.2 E1.2

Width of kits (mm) Depth (mm) Width of column (mm)
Height of kits
(mm) 600 800 700 900 600 800
500 PSHW5061(2) PSHW5081(2) PSVS0055(2) PSVS0057(2) PCVS5060(2) PCVS5080(2)
* For horizontal/vertica Emax E1.2 fixed see page 7/12 (kit H=400mm) and 7/14 (kit H=450mm).
(1)
Also suitable for vertical T7 witdrawable and witdrawable interlocked.
(2)
Also suitable for horizontal T7 witdrawable and witdrawable interlocked.

6
Bottom segregations Side segregations
Structures with rear inter- Structures with rear
mediate upright on intermediate upright on Structures without intermediate rear upright Assembly between intermediate upright
busbar side output side full-width segregation and rear structural upright
E2.2/E4.2 E2.2/E4.2 E2.2/E4.2 E6.2 E2.2/E4.2 E6.2
Width of
Height of kits (mm) Height of kits (mm)
Kit/column Depth
(mm) 600 600 600 700 (mm) 600 700
600 PRVS3061 PRVS3062 PRVS3060 700 PLVS3072 PLVS3572
800 PRVS3081 PRVS3082 PRVS3080 900 PLVS3092 PLVS3592
1000 PRVS3010 PRVS3510
1250 PRVS3125 PRVS3501
Bottom segregations Side segregations

Structures with rear inter- Structures with rear
mediate upright on intermediate upright on Structures without intermediate rear Assembly between intermediate upright
busbar side output side upright full-width segregation and rear structural upright
Width of
Kit/column Height of
(mm) 500 600 500 600 500 600 700 kits (mm) 500 700 900
600 PRVS2561 PRVS3061 PRVS2562 PRVS3062 PRVS2560 PRVS3060 500 PLVS2552 PLVS2572 PLVS2592
800 PRVS2581 PRVS3081 PRVS2582 PRVS3082 PRVS2580 PRVS3080 600 PLVS3052 PLVS3072 PLVS3092
1000 PRVS2510 PRVS3010 PRVS3510 700 PLVS3552 PLVS3572 PLVS3592
1250 PRVS2512 PRVS3125 PRVS3501
Form 2b Vertical circuit-breakers Form 4b Form 4b is obtained by duplicating the codes of vertical
Breakers whit rear terminals. bottom segregations PRVS... and vertical side segregations PLVS...,
use dedicated kit 2a-3a and shelf closing the circuit-breaker compartments over the entire height
PTHS... page 6/30. of the switchboard and installing an additional vertical side
segregation on the output side.
As an alternative to the PLVS... vertical side segregations, in the
case of main circuit-breakers, use the PMCS... side connection
module for fixing terminal extensions and the relative fixing bshelfets
PBMC0002 (page 4/40).

System pro E power
General information
Choice of busbars segregation
Horizontal busbars
Segregation for horizontal busbars: at top, at the bottom and at each height (1)
Structure External cable compartment Internal cable compartment
Form 2b Form 2b, 3b, 4b Form 2b, 3b, 4b
Without intermediate upright Without intermediate upright Without intermediate upright side structure
Front segre- Front segre- Front segre-
Horizontal shelves gations Horizontal shelves gations Horizontal shelves gations
Depth Height Depth Height Depth Height
(mm) (mm) (mm) (mm) (mm) (mm)
6 Width
(mm) 300 500 700 200 300 500 700 900 200 300 500 700 900 200
200 PTHS2030 PTHS2050 PTHS2070 PTHS2090 PFVS2220
300 PTHS3030 PTHS3050 PTHS3070 PTHS3090 PFVS2130
400 PTHS4030 PTHS4050 PTHS4070 PFVS2040 PTHS4030 PTHS4050 PTHS4070 PTHS4190 PFVS2140 PTHS4230 PTHS4250 PTHS4270 PTHS4290 PFVS2240
600 PTHS6030 PTHS6050 PTHS6070 PFVS2060
800 PTHS8030 PTHS8050 PTHS8070 PFVS2080
1000
1250
(1)
Busbars at each height are foreseen only for segregation form different from Form 2b.
For the closing at the back off the structure use Form 3b segregations PRVS.... busbars/outgoing side at whole height.
Vertical busbars
Side segregation for vertical busbars
Structure
Form 2b Form 2b (2) Form 2b, 3b, 4b
With intermediate upright
Without intermediate upright Front Rear
Depht (mm) Depth (mm)
Height
(mm) Type 200 300 500 700 900 179 500 700 900
700 blind PLVS7052 PLVS7072 PLVS7092
800 blind PTBS8020 PTBS8030 PTBS8050 PTBS8070 PTBS8090 PTBS8001 PTBS8052 PTBS8072 PTBS8091
1000 blind PTBS1020 PTBS1030 PTBS1050 PTBS1070 PTBS1001 PTBS1052 PTBS1072 PTVB1091
800 pre-cut PTVS8020 PTVS8030 PTVS8050 PTVS8070 PTVS8001 PTVS8052 PTVS8072 PTVS8091
1000 pre-cut PTVS1020 PTVS1030 PTVS1050 PTVS1070 PTBS1090 PTVS1001 PTVS1052 PTVS1072 PTVS1091
Segregation Form 3b, 4b from the intermediate upright up to the front structural upright can be obtained only by means of lateral segregation closing Form 2a-3a.
(2)
For the closing at the back off the structure use Form 3b segregations PRVS.... busbars/outgoing side at whole height.

Segregation for horizontal busbars: at top, at the bottom and at each height (1)
Structure External cable compartment Internal cable compartment
Form 2b, 3b, 4b Form 2b, 3b, 4b Form 2b, 3b, 4b Form 3b, 4b
With intermediate upright With intermediate upright With intermediate upright side structure
Front Horizontal Front Horizontal Front Front segregations
Horizontal shelves segregations shelves segregations shelves segregations at each heights
Depth Height Depth Height Depth Height Height
(mm) (mm) (mm) (mm) (mm) (mm) (mm)
6
500 700 900 200 (2) 300 (3) 500 700 900 200 (2) 300 (3) 500 700 900 200 300 200 (2) 300 (3)
PTHS2052 PTHS2072 PTHS2092 PFVS2222 PFVS3222 PFVS2223 PFSV3223
PTHS3052 PTHS3072 PTHS3092 PFVS2132 PFVS3132
PTHS4052 PTHS4072 PTHS4092 PFVS2042 PFVS3042 PTHS4152 PTHS4172 PTHS4192 PFVS2042 PFVS3042 PTHS4252 PTHS4272 PTHS4292 PFVS2242 PFVS3242 PFVS2243 PFVS3243
PTHS1292 PFVS2122 PFVS3122
(1)
Busbars at each height are foreseen only for segregation form different from Form 2b. (2)
For busbars at each height ≤100mm; for busbars at the top/bottom < 120mm.
(3)
For busbars at each height >100mm; for busbars at the top/bottom >120mm.
Cable compartment
Rear segregation
for internal cable
Blind side segregation for ex- Rear segregation compartment with Internal door for Internal door for Front vertical segre- Front vertical seg-
ternal cable compartment with for external cable rear intermediate external cable internal cable com- gation for external regation for internal
intermediate upright compartment upright compartment partment cable compartment cable compartment
Depth (mm) Width (mm) Width (mm) Width (mm) Width (mm) Width (mm) Width (mm)
Height
(mm) 500 700 900 300 400 200 400 300 400 200 400 300 400 200 400
700 PLVS7052 PLVS7072 PLVS7092
800 PTBS8052 PTBS8072 PTBS8091 PRVS8062 PRVS8082 PRBS8220 PRBS8240
1000 PTBS1052 PTBS1072 PTVB1091 PRVS1062 PRVS1082 PRBS1220 PRBS1240
1800 PDCB1830 PDCB1844 PDCB1820 PDCB1840 PFVS8030 PFVS8040 PFBS8020 PFBS8040
2000 PDCB2030 PDCB2044 PDCB2020 PDCB2040 PFVS1030 PFVS1040 PFBS1020 PFBS1040

6

System pro E power
spaces in between.
RANGE IDENTIFIER
System pro E powerr

S = Segregation
R = Rear
L = Lateral
C = Crosspiece
P = Pre-cut 6
F = Frontal
C = Cell
T = Total
V = Vertical
H = Horizontal
B = Blind
R = Rubber
D = Nylon
S = Structure/Struttura Segregation/Segregazione
F = Fixed/Fisso
W = Withdrawable/Estraibile
MEASUREMENTS
The last 4 numbers usually refer to a measurement of the component or
several dimensions pertaining to the code.
P S H S 6 0 5 0

System pro E power
Order codes - Form 2a-3a segregations
Intermediate side and rear upright for assembly of internal kits and segregations
The intermediate upright is the same as the one used for installing the kits and can be assembled both on the side
and bottom of the structure.
Dimensions
(mm)
Order ABB Package/
Intermediate upright 1800 PUKI1800 1STQ008039A0000 1/1
6 Universal horizontal shelf

Horizontal shelf to use whenever the plates of the circuit-breakers are further than 38mm , and above and below
the kit compositions (top and bottom). For structures with intermediate uprights.
Dimensions
(mm)
Order ABB Package/
≥38mm Description W code code No. pcs
Universal horizontal shelf 400 PSHS1904 1STQ008691A0000 1/1
NEW Universal horizontal shelf 1250 PSHS1912 1STQ001567B0000 1/1
Universal compartment side closing element

Precut universal compartment side closing element for use with both horizontal and vertical circuit-breakers. Pre-
engineered for housing compartment side closing elements in rubber. For structures with intermediate uprights.
Dimensions
(mm)
Order ABB Package/
2 compartment side closing elements 200 PPVS2200 1STQ008695A0000 1/2
> Selection guides page 7/12 > Technical details page 7/1 > Overall dimensions page 8/1

Rubber cover for closing compartments at the side
Rubber cover for closing compartments at the side and routing connections
Cell Rubber
dimensions dimensions
(mm) (mm)
Order ABB Package/
Description H H code code No. pcs
Rubber cover 150 - PPRS0150 1STQ008726A0000 1/1
Rubber cover 200 150 PPRS0200 1STQ008583A0000 1/1
PPRS0150 PPRS0200.... Rubber cover 250 200 PPRS0250 1STQ008584A0000 1/1
....PPRS0600
6
Segregation of modular assemblies
The code refers to two side walls. The segregation must be completed by ordering a front segregation and two
PSHS... universal shelves, above and below. For structures with intermediate uprights.
Dimensions
PFVS.... (mm)
Order ABB Package/
No.2 Side closing elements for DIN rail 200 PPDS0200 1STQ009080A0000 1/2
NEW No.2 Side closing elements for DIN rail 300 PPDS0300 1STQ001563B0000 1/2
PPDS.... PSHS....
Front segregation 200 400 PFVS2042 1STQ008539A0000 1/1
The side closing elements pre-cuts for DIN rail measure H=50mm; from a rubber cover PPRS0200 it is possible to obtain 3 rubber
covers for DIN rail H=50mm each.
Segregation for Unifix H
Dimensions
(mm)
Order ABB Package/
No. 2 Side closing elements for Unifix H 300 PLSU0300 1STQ001333B0000 1/2

System pro E power
Order codes - Form 2a-3a segregations
E1.2 horizontal Segregation for the SACE Emax 2 circuit-breaker

The codes include two horizontal shelves, one rear plate and two side walls. For structures with intermediate uprights.
Dimensions
(mm)
Emax 2 circuit- Order ABB Package/
breaker Version H W code code No. pcs
Horizontal circuit-breakers
E1.2 W 500 600 PSHW5061(1) 1STQ009281A0000 1/1
E1.2 W 500 800 PSHW5081(1) 1STQ009282A0000 1/1
Vertical circuit-breakers
E1.2 W 500 600 PSVW5061(2) 1STQ009055A0000 1/1
E1.2 W 500 800 PSVW5081(2) 1STQ009056A0000 1/1
E2.2 F 600 600 PSVF6062 1STQ009057A0000 1/1
E1.2 - E2.2 - E4.2 - E6.2 vertical E2.2 F 600 800 PSVF6082 1STQ009058A0000 1/1
E2.2 W 600 600 PSVW6062 1STQ009059A0000 1/1
E2.2 W 600 800 PSVW6082 1STQ009060A0000 1/1
E4.2 F 600 600 PSVF6064 1STQ009061A0000 1/1
6 E4.2 F 600 800 PSVF6084 1STQ009062A0000 1/1
E4.2 W 600 600 PSVW6064 1STQ009063A0000 1/1
E4.2 W 600 800 PSVW6084 1STQ009064A0000 1/1
E6.2 F 700 1000 PSVF7016 1STQ009065A0000 1/1
E6.2 F 700 1250 PSVF7126 1STQ009066A0000 1/1
E6.2 W 700 1000 PSVW7016 1STQ009067A0000 1/1
E6.2 W 700 1250 PSVW7126 1STQ009068A0000 1/1
(1)
Also suitable for horizontal T7 witdrawable and witdrawable interlocked.
(2)
NEW Segregation for the SACE Emax 2 circuit-breaker for space-saving

column W=400mm
The codes include two horizontal shelves, one rear plate and two side walls. For structures with intermediate uprights.
Dimensions
(mm)
breaker Version H W code code No. pcs
E1.2 W 600 400 PSVW6041 1STQ001568B0000 1/1
E2.2 F 600 400 PSVF6042 1STQ001569B0000 1/1
E2.2 W 600 400 PSVW6042 1STQ001570B0000 1/1
Key:
F fixed
W withdrawable

Blind compartment for segregations
Blind compartment for filling empty spaces inside the structure. The blind compartments are not suitable for fixing
accessories. For structures with intermediate uprights.
Dimensions
(mm)
Order ABB Package/
Blind compartment 50 400 PCBS5040 1STQ008703A0000 1/1
6
Not to mount above or below a kit with MO or a recessed external panels PPBR…
In this cases it is necessary using blind mounting plate and a blind flat panel to reach the segregation form 2A-3A.

System pro E power
Order codes - Busbar segregations Form 2b-3b-4b
and bottom of the structure.
Dimensions
(mm)
Order ABB Package/
The intermediate upright is required for all segregation Forms differing from Form 2b, even when not needed by the circuit-breaker version.
Side segregation for structure without intermediate upright

Vertical side walls for assembly between front and rear structural uprights. To use for structures with fixed circuit-
breakers that do not require the intermediate upright. The precuts in the segregations are at 50mm pitch. At least
6 three vertical ones must be removed.
Dimensions
(mm)
Order ABB Package/
Precut
Precut vertical side segregation 800 200 PTVS8020 1STQ009070A0000 1/1
Blind
Blind vertical side segregation 800 200 PTBS8020 1STQ009072A0000 1/1
Blind vertical side segregation 800 900 PTBS8090 1STQ002004B0000 1/1
Blind vertical side segregation 1000 900 PTBS1090 1STQ002005B0000 1/1

Front side segregation for structure with intermediate upright
Precut vertical front side wall for assembly between intermediate upright and front structural upright.
Dimensions
(mm)
Order ABB Package/
Precut vertical front side segregation
Vertical side segregation 800 PTVS8001 1STQ008511A0000 1/1
Vertical side segregation 1000 PTVS1001 1STQ008512A0000 1/1
Blind vertical front side segregation
Vertical side segregation 800 PTBS8001 1STQ008513A0000 1/1
Vertical side segregation 1000 PTBS1001 1STQ008514A0000 1/1
Segregation Form 3b, 4b from the intermediate upright up to the front structural upright can be obtained only by means of lateral segregation closing
Form 2a-3a.
Rear side segregation for structure with intermediate upright

Precut vertical rear side wall for assembly between intermediate upright and rear structural upright.
Dimensioni
(mm)
Order ABB Package/
Descrizione H D code code No. pcs
Segregazione verticale laterale posteriore con pretranciature
Vertical side segregation 800 500 PTVS8052 1STQ008515A0000 1/1
Blind vertical rear side segregation
Vertical side segregation 700 500 PLVS7052 1STQ009131A0000 1/1
Vertical side segregation 800 500 PTBS8052 1STQ008521A0000 1/1
NEW Vertical side segregation 800 900 PTBS8091 1STQ008525A0000 1/1
NEW Vertical side segregation 1000 900 PTVB1091 1STQ008526A0000 1/1

System pro E power
Rubber cover for precuts

Rubber cover for precut vertical segregation for routing the connections that can be installed on vertical segrega-
tions with precuts.
Dimensions
of rubber
Rubber cover 150 PPRS0200 1STQ008583A0000 1/1
For precuts H = 800mm use No. 2 rubber cover H = 400mm PPRS0450

6 For precuts H = 1000mm use No. 1 rubber cover H = 450mm PPRS0500 and No. 1 rubber cover H = 550mm PPRS0600
Horizontal busbar segregation in structures without intermediate upright

Form 2b
Full-width and full-depth horizontal segregations and full-width vertical segregations for routing busbars installed
horizontally on the top, on the bottom, behind an empty compartment H=200mm, for structures without intermedi-
ate uprights.
Dimensions
(mm)
Order ABB Package/
Horizontal busbar shelves
Horizontal shelf 400 300 PTHS4030 1STQ008499A0000 1/1
Front busbar segregations

Horizontal busbar segregation for external cable compartment without
intermediate upright Form 2b
Full-width and full-depth horizontal shelves and front busbar segregations for external cable compartments.
Dimensions
(mm)
Order ABB Package/
6
Horizontal busbar segregation for internal cable compartment without

intermediate upright Form 2b
Full-width and full-depth horizontal shelves and front busbar segregations for internal cable compartments.
Dimensions
(mm)
Order ABB Package/

System pro E power
Horizontal busbar segregation in structures with intermediate upright

Horizontal shelves and front segregations for routing busbars installed horizontally on the top, on the bottom and
at each heights. The busbar area can be 200 or 300mm in height.
Dimensions
(mm)
Order ABB Package/
Horizontal shelves for busbars under the top, on the bottom and at each heights
6 Horizontal shelf 800 900 PTHS8092 1STQ008537A0000 1/1
Horizontal shelf 1250 900 PTHS1292* 1STQ009074A0000 1/1
Front segregation for busbars under the top, on the bottom and at each heights
Busbars at each heights can be used only for segregation forms different from Form 2b.
Horizontal busbar segregation in external cable compartment with intermediate

upright
Full-width rear horizontal shelves and front busbar segregations for assembly between intermediate upright and
structural rear upright in external cable compartments.
Dimensions
(mm)
Order ABB Package/
Front segregation for busbars under the top, on the bottom and at each heights

Horizontal busbar segregation in internal cable compartments with intermediate
upright
Full-width rear segregation for horizontal busbars. Assembly between intermediate upright and structural rear upright.
Dimensions
(mm)
Order ABB Package/
Dimensions
(mm)
Order ABB Package/
Front rear segregation for busbars under the top or on the bottom 6
Front rear segregation for busbars at each heights
NEW Lateral segregation for horizontal busbars system

Dimensions
(mm)
Order ABB Package/
Lateral segregation 200 500 PLLS2050 1STQ001590B0000 1/1
and bottom of the structure. The intermediate upright is necessary for horizontal breakers in Form 3b.
Dimensions
(mm)
Order ABB Package/

System pro E power
Order codes - Form 3b segregations
Intermediate crosspiece for rear intermediate uprights

The intermediate crosspiece is necessary only for horizontal breakers in order to assemble terminals segregations
when the breakers is installed in the first available position in the structure (under the roof) or in the last available
position of the structure (bottom).
Dimensions
(mm)
Order ABB Package/
Description D code code No. pcs
Intermediate crosspiece 500 PCIS0500 1STQ009165A0000 1/1
Side wall for input side. For blind compartment

To assemble from front upright to intermediate upright.
Dimensions
(mm)
Order ABB Package/
6 Description H code code No. pcs
Side wall for blind compartment 50 PPBS0050 1STQ009168A0000 1/1
Side wall for blind compartment 150 PPBS0150 1STQ001230B0000 1/1
Horizontal circuit-breaker segregation in structures with intermediate rear upright

Rear vertical segregation with sliding plate at the same height as the circuit-breaker compartment. Assembly between
the input and output terminals for horizontal circuit-breakers, from plate to rear intermediate upright.
Dimensions
(mm)
Order ABB Package/
Vertical terminal separator 200 500 PSVS2050 1STQ008727A0000 1/1
Vertical terminal separator 500 700 PSVS0055* 1STQ009160A0000 1/1
Vertical terminal separator 500 900 PSVS0057* 1STQ009161A0000 1/1
*For Tmax T7 and Emax E1.2 W and W - I

NEW Horizontal circuit-breaker segregation in structures with intermediate rear
upright (for Tmax T e XT motorized)
Rear vertical segregation with sliding plate at the same height as the circuit-breaker compartment. Assembly between
the input and output terminals for horizontal circuit-breakers, from plate to rear intermediate upright.
Dimensions
(mm)
Kit for installation of Order ABB Package/
Description Tmax circuit-breakers H D code code No. pcs
XT1-XT2-XT3-XT4 3/4 P MO
Vertical terminal T4 3/4P F MO
200 500 PSVS2051 1STQ002056B0000 1/1
separator T5 3P F MO 400/630A
XT2 3P W MO
200 700 PSVS2071 1STQ002057B0000 1/1
XT2 3P W MO
200 900 PSVS2091 1STQ002058B0000 1/1
XT2 3P W MO 6
Vertical terminal T5 3/4P F MO 400/630A
250 500 PSVS2551 1STQ002059B0000 1/1
separator XT2 XT4 3/4P W MO
250 700 PSVS2571 1STQ002060B0000 1/1
250 900 PSVS2591 1STQ002061B0000 1/1
Vertical terminal
T5 3P W MO 300 500 PSVS3051 1STQ002062B0000 1/1
separator
Vertical terminal
T5 3P W MO 300 700 PSVS3071 1STQ002063B0000 1/1
separator
Vertical terminal
T5 3P W MO 300 900 PSVS3091 1STQ002064B0000 1/1
separator
Vertical terminal T5 3/4P W MO 400A
350 500 PSVS3551 1STQ002065B0000 1/1
separator T6 3P W MO
Vertical terminal T5 3/4P W MO 400A
350 700 PSVS3571 1STQ002066B0000 1/1
Vertical terminal T5 3/4P W MO 400A 1STQ002067B0000
350 900 PSVS3591 1/1
Vertical terminal
T6 3/4P W MO 500 500 PSVS5052 1STQ002379B0000 1/1
separator
Vertical terminal
T6 3/4P W MO 500 700 PSVS5072 1STQ002380B0000 1/1
separator
Vertical terminal
T6 3/4P W MO 500 900 PSVS5092 1STQ002381B0000 1/1
separator
Vertical terminal
T5 3/4P P MO 250 500 PSVS2553 1STQ002382B0000 1/1
separator
Vertical terminal
T5 3/4P P MO 250 700 PSVS2573 1STQ002383B0000 1/1
separator
Vertical terminal
T5 3/4P P MO 250 900 PSVS2593 1STQ002384B0000 1/1
separator
Vertical terminal
T6 3P F MO 300 500 PSVS5053 1STQ002385B0000 1/1
separator
Vertical terminal
T6 3P F MO 300 700 PSVS5073 1STQ002386B0000 1/1
separator
Vertical terminal
T6 3P F MO 300 900 PSVS5093 1STQ002387B0000 1/1
separator
Vertical terminal
T6 3/4P F MO 350 500 PSVS3553 1STQ002388B0000 1/1
separator
Key: Vertical terminal
T6 3/4P F MO 350 700 PSVS3573 1STQ002389B0000 1/1
separator
Vertical terminal
P - MO plug-in motor-operated T6 3/4P F MO 350 900 PSVS3593 1STQ002390B0000 1/1
W - MO withdrawable motor-operated separator

System pro E power
Rear segregation for blind compartment

Rear vertical segregation with plate for blind compartment.
Dimensions
(mm)
Order ABB Package/
Rear vertical separator blind compartment 50 500 PSVS0505 1STQ009086A0000 1/1
6 Rear vertical separator blind compartment 50 900 PSVS0509 1STQ009098A0000 1/1
Segregation for busbar side of horizontal circuit-breaker in structures with

intermediate rear upright
Vertical rear bottom segregation with height equal to the compartment height and width equal to the distance
between intermediate rear upright and structural rear upright on the busbar side.
Dimensions
(mm)
Order ABB Package/
Segregation bottom busbar side 200 400 PRVS2041 1STQ008765A0000 1/1
Segregation bottom busbar side 50 800 PRVS0581 1STQ001970B0000 1/1
For the closing of consecutive compartments it is possible to use the segregations at each height page 6/42.

Side segregations for horizontal circuit-breakers in structures with intermediate
upright and rear structural upright
Vertical rear side segregation with height equal to circuit-breaker compartment height. Assembly between
intermediate upright and rear structural upright. H=800mm or H=1000mm segregations can be used as
alternatives. When the installation of the busbars fixing crosspieces is needed with side segregations, use the
PBBT0008 fixing brackets.
Dimensions
(mm)
Order ABB Package/
Side compartment segregation 200 500 PLVS2052 1STQ008886A0000 1/1
Side compartment segregation 200 700 PLVS2072 1STQ008896A0000 1/1 6

System pro E power
Vertical circuit-breaker segregation in structures with or without intermediate rear

upright
Horizontal rear segregation to fix behind plate as wide as the structure. In sheet metal for moulded-case Tmax T,
XT and E1.2 fixed circuit-breakers. Useful for separating the terminals in vertical circuit-breakers. Pre-engineered
for the presence/absence of an intermediate rear upright.
Dimensions
(mm)
Order ABB Package/
Horizontal terminal separator 400 500 PSHS4050 1STQ008751A0000 1/1
6 Horizontal terminal separator 800 900 PSHS8090 1STQ008761A0000 1/1

Segregation for SACE Emax2 vertical circuit-breakers in structures with or
without intermediate upright
Dimensions
(mm)
Emax 2 Order ABB Package/
circuit-breaker Version W D code code No. pcs
E1.2 W 600 500 PSHW6051(1) 1STQ009031A0000 1/1
E1.2 W 600 700 PSHW6071(1) 1STQ009032A0000 1/1
E1.2 W 600 900 PSHW6091 1STQ009917A0000 1/1
E1.2 W 800 500 PSHW8051(1) 1STQ009033A0000 1/1
E1.2 W 800 700 PSHW8071(1) 1STQ009034A0000 1/1
E1.2 W 800 900 PSHW8091 1STQ009918A0000 1/1
E2.2 F 600 700 PSHF6072 1STQ009035A0000 1/1
E2.2 F 600 900 PSHF6092 1STQ009036A0000 1/1
E2.2 F 800 700 PSHF8072 1STQ009037A0000 1/1
E2.2 F 800 900 PSHF8092 1STQ009038A0000 1/1
E2.2 W 600 700 PSHW6072 1STQ009039A0000 1/1
E2.2 W 600 900 PSHW6092 1STQ009040A0000 1/1 6
E2.2 W 800 700 PSHW8072 1STQ009041A0000 1/1
E2.2 W 800 900 PSHW8092 1STQ009042A0000 1/1
E4.2 F 600 700 PSHF6072 1STQ009035A0000 1/1
E4.2 F 600 900 PSHF6092 1STQ009036A0000 1/1
E4.2 F 800 700 PSHF8072 1STQ009037A0000 1/1
E4.2 F 800 900 PSHF8092 1STQ009038A0000 1/1
E4.2 W 600 700 PSHW6074 1STQ009047A0000 1/1
E4.2 W 600 900 PSHW6094 1STQ009048A0000 1/1
E4.2 W 800 700 PSHW8074 1STQ009049A0000 1/1
E4.2 W 800 900 PSHW8094 1STQ009050A0000 1/1
E6.2 F 1000 900 PSHF1096 1STQ009051A0000 1/1
E6.2 F 1250 900 PSHF1296 1STQ009052A0000 1/1
E6.2 W 1000 900 PSHW1096 1STQ009053A0000 1/1
E6.2 W 1250 900 PSHW1296 1STQ009054A0000 1/1
(1)
NEW Segregation for the SACE Emax 2 circuit-breaker for space-saving column
W=400mm
Dimensions
(mm)
breaker Version D W code code No. pcs
E1.2 W 500 400 PSHW4051 1STQ001571B0000 1/1
E1.2 W 700 400 PSHW4071 1STQ001572B0000 1/1
E1.2 W 900 400 PSHW4091 1STQ001573B0000 1/1
E2.2 F 700 400 PSHF4072 1STQ001574B0000 1/1
E2.2 F 900 400 PSHF4092 1STQ001575B0000 1/1
E2.2 W 700 400 PSHW4072 1STQ001576B0000 1/1
E2.2 W 900 400 PSHW4092 1STQ001577B0000 1/1

System pro E power
Vertical circuit-breaker segregation (segregation on busbar side) for fixed/

interlocked T5, T6, T7 and E1.2 in structures with intermediate rear uprights
Vertical rear bottom segregation with height equal to half the compartment height and width equal to the
distance between intermediate rear upright and structural rear upright on the busbar side.
Dimensions
(mm)
Order ABB Package/
Segregation on bottom busbar side 175 400 PRVS1741 1STQ008764A0000 1/1
6 Segregation on bottom busbar side 175 800 PRVS1781 1STQ008784A0000 1/1
Vertical circuit-breaker segregation (segregation on busbar side) for Emax air

circuit-breakers in structures with intermediate rear uprights
distance between intermediate rear upright and structural rear upright on the busbar side.
Dimensions
(mm)
Order ABB Package/

Vertical circuit-breaker segregation (segregation on output side) for fixed/
interlocked T5, T6, T7 and E1.2 in structures with intermediate rear uprights
distance between intermediate rear upright and structural rear upright on the output side.
Dimensions
(mm)
Order ABB Package/
Segregation on bottom output side 175 600 PRVS1762 1STQ008814A0000 1/1
6
Vertical circuit-breaker segregation (segregation on output side) for SACE Emax 2

air circuit-breakers in structures with intermediate rear uprights
distance between intermediate rear upright and structural rear upright on the output side.
Dimensions
(mm)
Order ABB Package/

System pro E power
NEW Vertical rear segregation in structures with intermediare rear upright

Dimensions
(mm)
Order ABB Package/
BUSBAR SIDE
OUTPUT SIDE
6 Segregation on bottom output side 50 600 PRVS0562 1STQ001978B0000 1/1
Segregation on bottom output side 50 800 PRVS0582 1STQ001979B0000 1/1
NEW Vertical rear segregation in structure without intermediate rear upright

Dimensions
(mm)
Order ABB Package/
Full-width vertical segregation on bottom 50 600 PRVS0560 1STQ001996B0000 1/1

NEW Lateral segregation in structure with intermediate upright
Dimensions
(mm)
Order ABB Package/
Side compartment segregation 50 500 PLVS0552 1STQ001986B0000 1/1

System pro E power
Segregation for vertical fixed/interlocked T5, T6, T7 and E1.2 circuit-breakers in

structures without intermediate upright.
Vertical rear bottom segregation with height equal to half the compartment height and full-width.

Dimensions
(mm)
Order ABB Package/
Full-width segregation on bottom 175 400 PRVS1740 1STQ008844A0000 1/1
6 Full-width segregation on bottom 225 800 PRVS2280 1STQ008866A0000 1/1
Segregation for SACE Emax2 vertical air circuit-breakers in structures without

intermediate rear upright
Vertical rear bottom segregation with height equal to half the compartment height and full-width.
Dimensions
(mm)
Order ABB Package/
Full-width vertical segregation on bottom 250 600 PRVS2560 1STQ008857A0000 1/1

Segregation for vertical fixed/interlocked T5, T6, T7 and E1.2 circuit-breakers with
intermediate upright and structural rear upright.
Vertical side segregation with height equal to half the circuit-breaker compartment height. Assembly between
intermediate upright and structural rear upright. H=800mm or H=1000mm segregations can be used.
Dimensions
(mm)
Order ABB Package/
Side compartment segregation 200 900 PLVS2092 1STQ008906A0000 1/1 6
Segregation for SACE Emax 2 vertical air circuit-breaker in structures with

intermediate upright and rear structural upright
Vertical side segregation with height equal to half the circuit-breaker compartment height. Assembly between
intermediate upright and rear structural upright. H=800mm or H=1000mm segregations can be used.

Dimensions
(mm)
Order ABB Package/

System pro E power
Vertical segregations at each height

To be used in alternative to (rear and side) cells vertical segregations, with different breakers combined together
up to H=700-800-1000mm.
Dimensions
(mm)
Order ABB Package/
Vertical segregatios at each height busbars side
Segregation at each height busbars side 700 400 PRVS7041 1STQ009122A0000 1/1
700
900 Segregation at each height busbars side 700 600 PRVS7061 1STQ009125A0000 1/1
1000 Segregation at each height busbars side 800 600 PRVS8061 1STQ009126A0000 1/1
6 Dimensions
(mm)
Order ABB Package/
Vertical side segregatios at each height
Side segregation at each height 700 500 PLVS7052 1STQ009131A0000 1/1
Side segregation at each height 800 500 PTBS8052 1STQ008521A0000 1/1
Side segregation at each height 1000 900 PTVB1091 1STQ008526A0000 1/1
Vertical circuit-breaker segregation in structures with intermediate rear upright

Vertical rear segregation 700/800/1000mm in height and width equal to the distance between intermediate
upright and structural rear upright on the output side.
Dimensions
(mm)
Order ABB Package/
Rear segregation output side 700 600 PRVS7062 1STQ009104A0000 1/1

Full-width vertical segregation on bottom
Full-width vertical rear segregation on bottom for structures without intermediate rear upright.
Dimensions
(mm)
Order ABB Package/
6
Internal door for internal cable compartment – Pickled steel sheet

Dimensions (mm)
Order ABB Package/
Description H W code code No.pcs
1800 200 PDCB1820 1STQ007753A0000 1/1
compartment
1800 400 PDCB1840 1STQ007754A0000 1/1
compartment
2000 200 PDCB2020 1STQ007755A0000 1/1
compartment
2000 400 PDCB2040 1STQ007756A0000 1/1
compartment
Vertical front segregation for internal cable compartment

Dimensions (mm)
Order ABB Package/
Vertical front segregation 1800 200 PFBS8020 1STQ001481B0000 1/1
NEW Vertical segregation at intermediate upright in internal cable container
Dimensions (mm)
Order ABB Package/

System pro E power
Internal door for external cable compartment – Pickled steel sheet

Dimensions (mm)
Order ABB Package/
1800 300 PDCB1830 1STQ008086A0000 1/1
compartment
1800 400 PDCB1844 1STQ008087A0000 1/1
compartment
2000 300 PDCB2030 1STQ008088A0000 1/1
compartment
2000 400 PDCB2044 1STQ008089A0000 1/1
compartment
Vertical front segregation for external cable compartment

6 To be used in IP3X protections degree enclosures Form 2a-3a or in segregated enclosures from Form 3b.
Dimensions (mm)
Order ABB Package/
Vertical front segregation 1800 300 PFVS8030 1STQ001485B0000 1/1
NEW Vertical segregation at intermediate upright in external cable container
Dimensions (mm)
Order ABB Package/

Internal cable compartment segregation
Blind rear vertical segregation for internal cable compartment.
Dimensions
(mm)
Order ABB Package/
Vertical rear segregation 800 200 PRBS8220 1STQ008915A0000 1/1
Rear segregation for external cable compartment

Blind rear vertical segregation for external cable compartment.
Dimensions
(mm)
Order ABB Package/
Vertical rear segregation 800 300 PRVS8062 1STQ009105A0000 1/1
Side segregation for external cable compartment

Blind side segregation for external cable compartment.
Dimensions
(mm)
Order ABB Package/
Vertical side segregation 1000 900 PTVB1091 1STQ008526A0000 1/1

System pro E power
The intermediate upright is the same as the one used for installing the kits and can be assembled both on the
side and bottom of the structure. The rear intermediate upright is necessary in order to mount the segregations
for horizontal breakers.
Dimensions
(mm)
Order ABB Package/
Use universal vertical shelf PSHS.... for each compartment in order to reach Form 4b.
6
Position P0
Choice of segregation to suit depth of circuit-breaker
For segregation 4b, choose kits corresponding to the depth of each circuit-breaker in the required
version, as indicated in the tables below.
Horizontal circuit-breakers with front terminals
Fixed P0 P0 P0 P0 P0 P0 P0 P0 P0
Fixed with direct crank handle (RHD) P0 P0 P0 P0 P0 P0 P0 P0
Fixed with motor operator (MO) P0 P0 P0 P0 P0
Fixed interlocked P0 P0 P0 P0 P0 P0 P0 P0 P0
Fixed interlocked motor-operated P0
Position P1
Horizontal circuit-breakers with rear terminals

Fixed P0 P0 P0 P0 P1 P1 P1 P1 P1
Fixed with direct crank handle (RHD) P1 P1 P1 P1 P1 P1 P1 P1
Fixed with motor operator (MO) P1 P1 P1 P1 P1
Fixed interlocked P1
Fixed interlocked motor-operated P1
Plug-in P0 P1 P1 P1 P1
Plug-in with direct crank handle (RHD) P1 P1 P1 P1 P1
Plug-in with motor operator (MO)
Plug-in interlocked
Position P2 Plug-in interlocked motor-operated
Withdrawable P1 P1 P1 P1 n n
Withdrawable with direct crank handle (RHD) P1 P1 P1 P1 n n
Withdrawable with motor operator (MO)
n See codes on page 6/16.
Posizion P2
The P2 segregations can replace the
P0 and P1 segregation in order to
obtain more useful space available
inside the compartment.

Position P0 Segregation for horizontal circuit-breakers in position 0
Sheet metal corner piece to fix to separator PSVS…. With vertical Lexan panel at compartment height.
Dimensions
(mm)
Assembly Order ABB Package/
Description position H W code code No. pcs
Corner piece and panel in Lexan P0 200 400 PCVS0204 1STQ008931A0000 1/1
Corner piece and panel in Lexan P0 500 600 PCVS0506 1STQ008945A0000 1/1 6
Position P1 Segregation for horizontal circuit-breakers in position 1

Sheet metal corner piece to fix on separator PSVS…. With vertical Lexan panel at compartment height, horizontal
shelf and side wall.
Dimensions
(mm)
Rear cubicle P1 200 400 PCVS1204 1STQ008963A0000 1/1

System pro E power
Posizion P2 Segregation for horizontal circuit-breakers in position 2

The P2 segregations can replace the P0
and P1 segregation in order to obtain
Sheet metal corner piece to fix on separator PSVS…. With vertical Lexan panel at compartment height,
more useful space available inside the horizontal shelf and side wall.
compartment.
Dimensions
(mm)
6 Rear cubicle P2 400 600 PCVS2406 1STQ009007A0000 1/1
Segregation for horizontal withdrawable Emax E1.2 and Tmax T7 circuit-breakers

The code includes corner piece, vertical Lexan panel, 2 horizontal shelves and side wall.
Dimensions
(mm)
Order ABB Package/
Rear cubicle 500 600 PCVS5060 1STQ009162A0000 1/1
Rear cubicle 500 800 PCVS5080 1STQ009163A0000 1/1
Horizontal segregation for cubicles

Horizontal shelf for cubicles for 4b segregation. Required for all depth changes in compartments in the same column.
Order the length corresponding to the larger position between two consecutive compartments.
Dimensions
(mm)
Description position W code code No. pcs
Horizontal shelf for cubicles P1 400 PSHS1400 1STQ008923A0000 1/1

Lateral connection module for terminal ditching
Lateral drilled module 25mm pitch for fixing the crosspieces with insulating supports in width from the intermediate
upright up to the rear structural upright. In order to complete the terminals ditching it is necessary to order two
lateral connection modules, which have to be fixed sideways. The crosspieces PCRM .... or PCRS .... is fixed
using the special fixing brackets for module connection PBMC0002. The crosspiece is to be chosen and ordered
separately according to the width of the structure.
PCRM.... H D Order ABB Package/
PCRS.... Description (mm) (mm) code code No. pcs
Lateral connection module 175 500 PMCS1755 1STQ009200A0000 1/1
PBMC0002
Lateral connection module 250 700 PMCS2570 1STQ009208A0000 1/1 6
No.2 fixing brackets connection module PBMC0002 1STQ009215A0000 1/2
Segregations for vertical circuit-breakers

Form 4b of vertical circuit-breakers is obtained by duplicating the codes of vertical bottom segregations PRVS... and
vertical side segregations PLVS..., closing the circuit-breaker compartments for the full height of the switchboard
and installing an additional vertical side segregation on the output side.
As an alternative to the PLVS... vertical side segregations, in the case of main circuit-breakers, use the PMCS... side connection
module for fixing terminal extensions and the relative fixing bshelfets PBMC0002 (page 4/40).

System pro E power
Mechanical and electrical characteristics 7/2

Declaration of conformity 7/4
Power dissipated 7/5
Handling 7/10
Electrical continuity 7/12
Calculation of protection conductor PE 7/13
Equipotential conductors 7/14
Mechanical shock resistance IK 7/15
Protection classes 7/16
Unifix wiring system

Connection examples - Unifix H 7/18
Connection examples - Unifix L 7/19
Configurations
Configuration examples 7/20

System pro E power
Mechanical and electrical characteristics

Conformity to Standard IEC 61439-1-2
System pro E power switchboards are subjected in the ABB laboratories, to the type tests established by Standard IEC 61439-1-2.
The results of these tests guarantee the performance of System pro E power switchboards and when ABB SACE structures, air circuit-
breakers, moulded-case and modular circuit-breakers are used, relieve the end manufacturer of the switchboard from having to perform
further type tests so long as he/it complies with the selection criteria and assembly instructions for the various different components.
Reference can be made to these results, described below, when drawing up the declaration of conformity of the switchboard.
Overtemperature (Ref. sect. 9.2. of the Standard)

Values from the type tests performed referring to all System pro E - Power switchboard sizes and to the type of
installation are given in the tables. The dissipated power data (in Watts) depend on the allowable overtemperature inside the upper part
of the switchboard and should be compared with the sum of the powers dissipated by all the components installed in the switchboard
(also taking the coincidence factor into due account).
Dielectric properties (Ref. sect. 10.9. of the Standard)

Rated service voltage up to 1000V AC / 1500V DC
Rated insulation voltage up to 1000V AC / 1500V DC
Rated impulse withstand voltage 8kV / 12kV
Short-circuit withstand capacity (Ref. sect. 10.11. of the Standard)

7 Rated short-time short-circuit line-to-line 120kA (1s)
current: 50kA (3s)
line-to-neutral 72kA (1s)
Rated max. peak short-circuit current 264kA
Protection against the circuit and short-circuit withstand (Ref. sect. 9.3. of the Standard)
Rated admissible short-time withstand current Icw for the protection circuit 72kA (1s)
Insulation clearances (Ref. sect. 10.4. of the Standard)

Insulation clearances are guaranteed when the assembly instructions provided with the ABB SACE structures and circuit-breakers are complied with.
Mechanical operation (Ref. sect. 10.13. of the Standard)

When the assembly instructions of the ABB SACE structures are circuit-breakers are complied with, mechanical operation can be considered as verified.
Protection class (Ref. sect. 10.3 of the Standard)

Protection class
obtained with re-
spect to the type Front sealing
of panelling profiles Door Rear Side panels Top Bottom Top profile
Blind
IP30 •* - •* •* •* •* -
IP31 •* - •* •* •* •* •*
IP40 - •* •* •* •* •* -
IP41 - •* •* •* •* •* •*
IP65 - • • • • • -
Vented
IP30 •* - • ** • ** •* •* -
IP31 •* - • ** • ** •* •* •*
IP40 - •* • *** • *** •* •*
IP41 - •* • *** • *** •* •* •*
* Codes in the catalogue allowing IP30-IP31 protection class to be obtained for structures without doors, IP40-IP41 for structures with doors. The structures change from IP30 to IP31 if the top sealing
kits are used in addition to the front sealing profiles. The structures change from IP40 to IP41 if the top sealing kits are used in addition to the doors.
** Codes in the catalogue for vented panels allowing IP30-31 protection class to be obtained for structures without doors. The structures change from IP30 to IP31 if the top sealing kits are used in
addition to the front sealing profiles.
*** Codes in the catalogue for vented panels allowing IP30-31 protection class to be obtained for structures without doors. The structures change from IP30 to IP40 adding the door and the grates for
vented panel. The structures change from IP30 to IP31 if the top sealing kits are used in addition to the front sealing profiles. The structures change from IP40 to IP41 if the top sealing kits are used in
addition to the doors.

Mechanical specifications
Material
Uprights and cross-pieces 12/10mm hot-dip galvanized sheet steel
12/10mm AISI 304 stainless steel
Plinth angle pieces 25/10mm hot-dip galvanized sheet steel
Plinth flanges 15/10mm hot-dip galvanized sheet steel
External panels pickled steel sheet thickness 8/10mm for IP30/40 and 15/10 for IP65
Doors 15/10mm thick pickled sheet steel. 4mm thick toughened glass glued from the inside
Plates 15/10mm hot-dip galvanized sheet steel
Panels 12/10mm pickled steel sheet
Partitions plastic components: thermoplastic vulcanizate
metal components: 15/10mm pickled steel sheet
Paint coating
Structure colour RAL 7035 grey orange peel finish
Plinth colour RAL 7012 grey orange peel finish
Standard cycle The sheet metal is cleaned
Phosphating, based on iron salts
Drying in a tunnel at 100°C
7
External and internal coating with electrostatic application of thermosetting powder coating with epoxy-polyester binders, RAL 7035 colour orange
peel finish, total thickness 60/70 microns.
Curing in an oven 180°C
Coating Binder: epoxy-polyester
characteristics
Specific gravity: 1.61g/cm3
Theoretic yield: 10.4m2/kg with film an average 60 microns thick
Melting point: 85-95 °C (Kofler bench method)
Particle size: standard distribution between 5 and 100 microns with 30 to 40 micron average particle size.
Setting: 12 min x 190 °C (temperature of object).
Hardness: 1H - 2H
DIN 53152 bending elasticity: unaltered on 1/4” mandrel
DIN 53151 cross-hatch adhesion: GT O (100%)
Erichem elasticity: SEN DIN 53156: > 6mm
Gardner inpact resistance: 25 kg x cm.
Tests performed on degreased and phosphatized metal plates with 60/70 micron film thickness.
The paint coating passed the saline mist resistance tests (193 hours).
Environmental characteristics
Type of installation indoor
Installation conditions on floor
Climatic conditions (t°/Rh%) constant 23°C/83% - 40°C/93%
variable 23°C/98% - 40°C/98%
Ambient temperature limits for operation -5°C +40°C Normal usage conditions (Ref. sect. 7.1 of the Standard IEC 61439-1-2)
for storage -25°C +55°C

System pro E power
ABB SACE Declaration of conformity

System pro E power switchboards with rated characteristics:
Rated service voltage Ue up to 1000V AC / 1500V DC
Rated insulation voltage Ui up to 1000V AC / 1500V DC
Rated current / Icw up to 6300A / fino a 120kA
IP protection class IP30, IP31, IP40, IP41, IP65
If the components have been chosen and assembled correctly, as described in the catalogue and instruction manual, the resulting
switchboards will conform to Standard IEC 61439-1-2, in accordance with the provisions established by the Low Voltage Directive
adopted by the European Union 2007/95/EC (formerly Directive 73/23/EEC, Law 791/1977).
The above is valid if the switchboard has been designed and built:
- having chosen the materials on the basis of the performance values indicated in the ABB catalogues;
- having sized the conductors in accordance with the provisions established by Standards EN 61439-1 and CEI 64-8;
- having performed the individual tests established by Standard IEC 61439-1-2 and obtained positive results.
Technical details
Information about disposal at the end of the lifecycle of the products
7 ABB SACE has conducted research into the end of the lifecycle of the product. The assessments were made by applying the LCA (Life
Cycle Assessment) method as established by ISO 14040 - 1997 and in accordance with the requirements established by SEMC in the
ISO TR 14025 TYPE III Enviromental declarations (MSR 1999:2 – “Guidelines Environmental Product Declarations”) document.
The research was conducted considering the disposal and recycling processes of the main materials forming a typical switchboard.
Using the bill of materials as a starting point, the researchers considered the ease with which each part can be disassembled and
separated as well as the ability to recycle the materials. They found that the product is almost entirely recyclable.
After this, they limited the bill of materials to the most significant components and assessed the lifecycle of each.
The result was the flow of recyclable materials and salvaged materials (or for incineration) indicated in the Table. In theory, none of the
materials should end up in a landfill.
Substance Destination
Aluminium scrap Recycling
Copper scrap Recycling
Polyurethane gaskets Incineration
Fiberglass Recycling
Scrapped glass Recycling
Paper/cardboard Recycling
Plastic insulators Recycling
Sheet metal scrap Recycling

Power dissipated
System pro E power IP31
Separate enclosure Separate enclosure for First and last First and last enclosures Central enclosure Central enclosure for
exposed on all sides assembly on a wall enclosures exposed for assembly on wall exposed assembly on a wall
Maximum power Maximum power Maximum power Maximum power Maximum power Maximum power
dissipated (W) dissipated (W) dissipated (W) dissipated (W) dissipated (W) dissipated (W)
W (mm) D (mm) 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C
Structures H = 1800mm with blind panels
400 200 223 280 338 400 208 258 314 371 208 262 315 374 187 234 281 332 193 246 296 350 170 215 260 310
400 300 257 322 389 460 242 301 366 433 237 298 359 425 216 270 324 383 217 276 332 393 194 245 297 353
400 500 290 364 440 520 276 344 418 494 265 333 402 476 244 305 367 434 240 305 367 435 218 274 333 395
400 700 371 461 560 668 349 440 535 622 329 410 495 588 300 377 457 539 297 370 455 536 273 343 415 491
400 900 445 553 672 802 419 528 642 746 395 492 594 706 360 452 548 647 356 444 546 643 328 412 498 589
600 200 285 357 433 511 259 324 393 464 268 336 407 481 237 297 359 424 255 320 387 457 223 279 338 400
600 300 328 412 499 589 302 378 458 541 306 383 464 549 273 342 414 489 286 359 434 513 254 319 386 456
600 500 371 466 564 666 344 432 523 617 343 430 521 616 309 387 469 553 316 397 481 568 285 358 434 512
600 700 428 537 651 769 426 535 648 765 407 511 619 731 388 486 589 695 384 481 583 688 352 442 535 632 7
600 900 514 644 781 923 511 642 778 918 488 613 743 877 466 583 707 834 461 577 700 826 422 530 642 758
800 200 356 446 540 638 319 400 484 572 339 425 515 608 296 371 449 530 327 410 496 586 283 355 430 508
800 300 390 489 592 699 367 461 558 659 374 469 568 671 339 425 514 607 365 458 554 654 321 403 488 577
800 500 423 531 643 759 415 521 631 745 408 512 621 733 381 478 579 684 402 505 611 722 359 451 546 645
800 700 489 614 743 877 478 599 726 857 463 581 703 830 450 564 683 807 454 570 690 815 434 544 659 778
800 900 587 737 892 1052 574 719 871 1028 556 697 844 996 540 677 820 968 545 684 828 978 521 653 791 934
1000 900 683 824 961 1098 670 812 968 1123 651 793 945 1102 632 776 927 1086 638 780 930 1089 612 757 913 1070
1250 900 799 964 1124 1285 784 950 1133 1314 762 928 1106 1289 739 908 1085 1271 746 913 1088 1274 716 886 1068 1252
400 200 242 304 368 435 224 268 337 399 223 280 339 399 200 251 304 359 209 260 316 377 183 230 278 329
400 300 277 349 422 498 261 314 393 465 254 318 385 454 203 289 350 413 234 291 354 422 208 262 316 374
400 500 312 393 476 561 297 360 448 530 284 356 431 508 260 327 395 467 258 322 392 466 233 293 354 419
400 700 393 495 598 705 378 475 577 680 356 444 538 636 306 386 469 550 319 397 480 565 291 365 442 525
400 900 472 594 718 846 454 570 692 816 427 533 646 763 367 463 563 660 383 476 576 678 349 438 530 630
600 200 304 382 463 546 277 347 420 496 287 360 436 514 253 317 384 454 273 342 415 489 237 298 360 426
600 300 343 431 522 616 324 406 491 580 327 410 497 586 292 384 444 524 307 384 466 549 271 340 411 486
600 500 382 479 581 685 370 464 562 663 367 460 557 658 331 451 503 594 340 426 516 609 304 381 462 545
600 700 441 554 671 792 435 546 662 781 416 522 632 746 408 512 620 732 406 509 617 728 373 468 566 669
600 900 529 665 805 950 522 655 794 937 499 626 758 895 490 614 744 878 487 611 740 874 448 562 679 803
800 200 368 462 559 660 340 427 517 610 362 454 550 650 315 395 479 565 349 437 530 625 301 378 458 541
800 300 402 504 611 721 381 479 580 684 390 489 592 700 359 450 546 644 381 433 579 684 341 428 518 612
800 500 436 546 662 781 422 530 642 758 417 524 634 749 402 505 612 722 413 519 628 742 380 477 578 682
800 700 512 643 778 919 494 620 751 887 480 602 729 861 461 578 701 827 466 585 709 837 451 566 685 809
800 900 614 772 934 1103 593 744 901 1064 576 722 875 1033 553 694 841 992 559 702 851 1004 541 679 822 971
1000 900 721 864 1022 1198 700 858 1023 1184 681 833 987 1145 659 799 947 1100 670 814 967 1123 653 792 938 1092
1250 900 844 1011 1196 1402 819 1004 1197 1385 797 975 1155 1340 771 935 1108 1287 784 952 1131 1314 764 927 1097 1278
Power dissipated inside System pro E power switchboards on the basis of the admissible overtemperature.
∆t = difference between the temperature inside the enclosure and ambient temperature.
Example
Enclosure IP31 H=1800mm, W=400mm, D=200mm esposed on all sides
Temperature inside the enclosure (t) °C 70 –

Ambient temperature (t) °C 35 =
∆t °C 35
Maximum power dissipated (W) 338

System pro E power
Power dissipated
System pro E power IP30/31
Separate enclosure exposed Separate enclosure for assembly on a First and last First and last enclosures for assembly
on all sides wall (values obtained with blind rear enclosures exposed on a wall (values obtained with blind
panels) rear panels)
Maximum power dissipated (W) Maximum power dissipated (W) Maximum power dissipated (W) Maximum power dissipated (W)
W (mm) D (mm) 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C
Structures H = 1800mm with ventilated panels
600 500 571 737 914 1102 541 698 866 1044 428 552 685 826 406 524 650 784
600 700 737 951 1180 1422 712 919 1140 1374 552 713 884 1066 518 668 829 999
800 500 649 837 1038 1252 611 788 978 1179 502 648 804 969 460 593 736 887
800 700 836 1079 1339 1613 787 1016 1261 1519 625 806 1000 1205 595 768 953 1149
1000 900 1295 1606 1926 2235 1147 1444 1750 2074 914 1146 1401 1666 818 1035 1266 1516
1250 900 1450 1799 2157 2503 1273 1603 1943 2302 1024 1284 1569 1866 908 1149 1405 1683
7 600 500 586 756 938 1131 546 705 874 1131 434 560 695 838 407 525 651 785
600 700 741 956 1186 1429 715 923 1145 1380 560 723 897 1081 527 680 843 1016
800 500 654 844 1047 1261 623 804 997 1202 507 654 811 978 468 604 749 903
800 700 861 1112 1379 1662 792 1022 1268 1528 640 826 1024 1234 596 769 955 1151
1000 900 1333 1655 1983 2301 1154 1452 1759 2086 935 1176 1434 1706 820 1036 1263 1520
1250 900 1493 1854 2221 2577 1281 1612 1952 2315 1047 1317 1606 1911 910 1150 1402 1687

Power dissipated
400 200 223 280 338 400 208 258 314 371 208 262 315 374 187 234 281 332 193 246 296 350 170 215 260 310
400 300 257 322 389 460 242 301 366 433 237 298 359 425 216 270 324 383 217 276 332 393 194 245 297 353
400 500 290 364 440 520 398 514 637 768 265 333 402 476 304 392 486 586 240 305 367 435 218 274 333 395
400 700 371 461 560 668 544 703 872 1051 329 410 495 588 382 493 612 738 297 370 455 536 273 343 415 491
400 900 445 553 672 802 725 937 1163 1401 395 492 594 706 449 580 720 868 356 444 546 643 328 412 498 589
600 200 285 357 433 511 259 324 393 464 268 336 407 481 237 297 359 424 255 320 387 457 223 279 338 400
600 300 328 412 499 589 302 378 458 541 306 383 464 549 273 342 414 489 286 359 434 513 254 319 386 456
600 500 371 466 564 666 462 596 739 891 343 430 521 616 350 451 560 674 316 397 481 568 285 358 434 512
600 700 428 537 651 769 627 809 1004 1210 407 511 619 731 438 565 701 845 384 481 583 688 352 442 535 632 7
600 900 514 644 781 923 836 1079 1339 1613 488 613 743 877 515 665 825 994 461 577 700 826 422 530 642 758
800 200 356 446 540 638 319 400 484 572 339 425 515 608 296 371 449 530 327 410 496 586 283 355 430 508
800 300 390 489 592 699 367 461 558 659 374 469 568 671 339 425 514 607 365 458 554 654 321 403 488 577
800 500 423 531 643 759 525 678 841 1013 408 512 621 733 405 523 648 781 402 505 611 722 359 451 546 645
800 700 489 614 743 877 689 889 1103 1329 463 581 703 830 473 661 819 988 454 570 690 815 434 544 659 778
800 900 587 737 892 1052 919 1185 1471 1772 556 697 844 996 556 778 964 1162 545 684 828 978 521 653 791 934
1000 900 683 824 961 1098 1072 1338 1634 1935 651 793 945 1102 650 891 1089 1303 638 780 930 1089 612 757 913 1070
1250 900 799 964 1124 1285 1190 1485 1814 2148 762 928 1106 1289 722 989 1209 1446 746 913 1088 1274 716 886 1068 1252
400 200 242 304 368 435 224 268 337 399 223 280 339 399 200 251 304 359 209 260 316 377 183 230 278 329
400 300 277 349 422 498 261 314 393 465 254 318 385 454 203 289 350 413 234 291 354 422 208 262 316 374
400 500 312 393 476 561 403 519 644 777 284 356 431 508 309 398 492 591 258 322 392 466 233 293 354 419
400 700 393 495 598 705 547 706 876 1056 356 444 538 636 389 498 617 743 319 397 480 565 291 365 442 525
400 900 472 594 718 846 729 941 1168 1408 427 533 646 763 458 586 726 874 383 476 576 678 349 438 530 630
600 200 304 382 463 546 277 347 420 496 287 360 436 514 253 317 384 454 273 342 415 489 237 298 360 426
600 300 343 431 522 616 324 406 491 580 327 410 497 586 292 384 444 524 307 384 466 549 271 340 411 486
600 500 382 479 581 685 466 602 747 900 367 460 557 658 353 456 565 681 340 426 516 609 304 381 462 545
600 700 441 554 671 792 632 815 1011 1219 416 522 632 746 448 578 717 864 406 509 617 728 373 468 566 669
600 900 529 665 805 950 843 1087 1348 1625 499 626 758 895 527 680 844 1016 487 611 740 874 448 562 679 803
800 200 368 462 559 660 340 427 517 610 362 454 550 650 315 395 479 565 349 437 530 625 301 378 458 541
800 300 402 504 611 721 381 479 580 684 390 489 592 700 359 450 546 644 381 433 579 684 341 428 518 612
800 500 436 546 662 781 536 692 859 1035 417 524 634 749 410 528 656 790 413 519 628 742 380 477 578 682
800 700 512 643 778 919 701 905 1123 1353 480 602 729 861 510 658 816 983 466 585 709 837 451 566 685 809
800 900 614 772 934 1103 935 1207 1497 1804 576 722 875 1033 600 774 960 1156 559 702 851 1004 541 679 822 971
1000 900 721 864 1022 1198 1103 1391 1699 1998 681 833 987 1145 714 891 1080 1281 670 814 967 1123 653 792 938 1092
1250 900 844 1011 1196 1402 1224 1544 1886 2218 797 975 1155 1340 793 989 1199 1422 784 952 1131 1314 764 927 1097 1278

System pro E power
Power dissipated
Separate enclosure exposed Separate enclosure for assembly on a First and last First and last enclosures for assembly
on all sides wall (values obtained with blind rear enclosures exposed on a wall (values obtained with blind
panels) rear panels)
Maximum power dissipated (W) Maximum power dissipated (W) Maximum power dissipated (W) Maximum power dissipated (W)
W (mm) D (mm) 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C 25 °C 30 °C 35 °C 40 °C
400 500 418 539 669 806 398 514 637 768 317 409 507 611 304 392 486 586
400 700 562 725 899 1084 544 703 872 1051 395 509 632 761 382 493 612 738
400 900 749 967 1199 1445 725 937 1163 1401 494 636 790 951 449 580 720 868
600 500 489 631 783 944 462 596 739 891 376 485 602 725 350 451 560 674
600 700 651 840 1042 1256 627 809 1004 1210 471 608 754 909 438 565 701 845
600 900 868 1120 1389 1675 836 1079 1339 1613 589 760 943 1136 515 665 825 994
800 500 560 723 897 1081 525 678 841 1013 438 565 700 844 405 523 648 781
7 800 700 733 946 1174 1415 689 889 1103 1329 524 676 838 1010 473 661 819 988
800 900 977 1261 1565 1887 919 1185 1471 1772 655 845 1048 1263 556 778 964 1162
1000 900 1135 1408 1688 1962 1072 1338 1634 1935 766 960 1173 1397 650 891 1089 1303
1250 900 1271 1577 1891 2197 1190 1485 1814 2148 858 1075 1314 1565 722 989 1209 1446
400 500 422 543 671 809 403 519 644 777 320 413 511 615 309 398 492 591
400 700 567 732 908 1094 547 706 876 1056 398 514 635 765 389 498 617 743
400 900 756 976 1211 1459 729 941 1168 1408 498 643 794 956 458 586 726 874
600 500 503 649 805 970 466 602 747 900 379 489 607 732 353 456 565 681
600 700 657 847 1051 1267 632 815 1011 1219 477 616 764 921 448 578 717 864
600 900 876 1129 1401 1689 843 1087 1348 1625 596 770 955 1151 527 680 844 1016
800 500 566 731 907 1093 536 692 859 1035 440 568 705 850 410 528 656 790
800 700 764 985 1222 1474 701 905 1123 1353 546 705 874 1054 510 658 816 983
800 900 1019 1313 1629 1965 935 1207 1497 1804 683 881 1093 1318 600 774 960 1156
1000 900 1196 1497 1782 2134 1103 1391 1699 1998 807 1016 1232 1460 714 891 1080 1281
1250 900 1340 1677 1996 2390 1224 1544 1886 2218 904 1138 1380 1635 793 989 1199 1422

Power dissipated
System pro E power IP65
400 300 223 284 344 406 213 267 323 381 206 258 313 370 188 236 286 338 188 236 286 338 170 213 258 305
400 200 193 242 293 346 179 224 271 320 178 223 270 319 160 201 243 287 165 207 251 296 146 184 222 263
400 500 260 326 395 466 247 310 375 443 235 294 357 421 217 272 329 389 212 266 322 381 194 243 295 348
400 700 328 411 498 588 317 398 482 569 290 364 440 520 274 344 417 492 259 325 394 465 243 304 369 435
400 900 386 484 586 692 373 468 567 669 341 428 518 612 322 405 491 579 305 382 464 547 286 358 434 512
600 300 292 366 443 524 268 336 407 481 271 341 413 488 242 304 368 435 279 319 386 456 226 284 343 406
600 200 254 318 385 455 230 289 350 413 238 299 362 428 210 264 320 378 227 285 345 407 198 249 301 356
600 500 331 415 502 593 306 384 465 549 305 383 464 548 275 344 417 493 282 353 428 505 254 319 386 456
600 700 381 478 579 684 379 476 577 681 362 455 551 650 345 433 524 619 341 428 519 612 314 393 477 563 7
600 900 448 562 681 805 446 560 679 801 426 535 648 765 406 509 616 728 401 504 611 720 369 462 561 662
800 300 346 435 526 622 326 409 496 586 332 417 505 596 301 378 458 540 324 407 493 581 286 358 434 413
800 200 316 397 481 568 284 356 431 509 302 378 458 541 263 330 400 472 291 365 442 521 252 316 383 452
800 500 377 473 572 676 369 463 561 663 363 456 552 652 339 426 516 609 358 449 544 642 320 401 486 574
800 700 435 546 661 781 425 533 646 763 412 517 626 739 400 502 608 718 404 507 614 725 386 484 586 692
800 900 512 642 778 919 500 627 760 898 485 608 736 869 471 591 715 845 475 596 722 853 454 569 689 814
1000 900 596 718 838 959 583 708 844 981 568 692 832 975 551 677 808 948 556 679 811 950 533 659 795 932
1250* 900 697 840 980 1122 682 828 987 1148 665 810 973 1141 645 792 945 1109 651 794 949 1112 624 771 930 1090
400 300 244 306 371 438 228 287 347 410 221 278 337 397 202 254 307 363 202 254 308 363 182 228 277 327
400 200 209 262 317 375 192 241 292 345 191 240 291 343 172 216 262 309 178 223 270 319 157 197 239 282
400 500 279 351 425 501 265 333 403 476 252 316 383 452 232 292 353 417 227 285 346 408 207 260 315 372
400 700 354 444 537 634 341 428 519 612 314 394 478 564 295 370 448 529 278 349 423 499 258 324 393 464
400 900 416 522 632 746 401 504 611 720 369 464 562 664 347 435 527 622 327 411 498 587 304 381 462 546
600 300 305 383 464 548 287 361 437 516 290 364 442 521 260 342 395 466 272 342 414 459 241 302 366 432
600 200 271 340 412 486 246 309 374 442 255 320 388 458 225 282 342 404 243 305 369 436 211 265 321 379
600 500 340 426 517 610 329 413 500 590 326 409 496 585 295 402 448 528 302 379 459 542 271 339 411 485
600 700 393 493 597 705 387 486 589 695 370 464 562 664 363 455 552 651 361 453 549 648 332 416 504 595
600 900 462 580 702 829 455 572 693 818 435 546 661 781 427 535 649 766 425 533 646 762 391 489 593 700
800 300 358 448 543 641 339 404 515 609 346 406 527 622 319 400 485 573 339 425 515 608 303 380 461 544
800 200 328 411 498 588 303 380 460 543 322 404 490 578 280 352 426 503 310 389 471 557 268 337 408 481
800 500 388 486 589 695 376 472 571 675 371 466 565 667 358 449 544 643 368 462 559 660 338 424 514 607
800 700 456 572 693 818 440 552 668 789 427 536 649 766 410 515 624 736 415 521 631 745 401 503 610 720
800 900 536 673 815 962 518 649 786 928 502 631 764 901 482 606 734 866 488 613 742 876 472 592 718 847
1000 900 629 753 892 1045 611 748 892 1092 593 728 862 998 574 697 826 960 585 710 843 980 569 690 819 952
1250 900 736 881 1044 1223 715 875 1044 1278 694 852 1009 1168 672 815 966 1123 684 831 986 1147 666 807 958 1114

System pro E power
Handling Shallow switchboards should be handled in the following way:

Handling with a transpallet
Side
A B
100 200 100
300mm
7
Check the center of gravity before handling structures measuring
L=800/1000mm (with internal or external cable compartment)
containing busbar systems.
A
Dimensions (mm)
Larghezza 300mm 198
Larghezza 400mm 298
Larghezza 600mm 498
Larghezza 800mm 698
Larghezza1000mm 898
Larghezza 1250mm 1098
For extra safety, it is advisable to fasten the switchboard to the lift

truck when using this type of vehicle for transport.

Handling with a bridge crane
Before handling switchboards with a crane or bridge crane, make sure that:
- the ropes or chains are in an excellent condition;
- the angle between the lifting ropes and the top of the switchboard must be ≥45°;
- up to 3 units can be carried at the same time;
- maximum weight lifted as established by Standard DIN 580 (M12).
To comply with the conditions described above, use a lifting beam with the appropriate characteristics when lifting several adjacent
units.
7
45° 45°
Standard DIN 580 concerning mechanical connection components (only for eyebolts)
Eyebolts Lifting reinforcements
B C D E F G Load 1 Load 2 Tightening

A (mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg) (Nm)
Eyebolts
M12 54 12 28 10 22 30 340 240 8*
Lifting reinforcements
M12 Ø40 37 80 25 Ø14 60 510 350 40
* Tighten by hand without mechanical aids because this can cause damages by reducing the scope of the eyebolt.

System pro E power
Electrical continuity of the structure and fixed and movable parts

The accessible metal parts in a switchboard must be electrically plates, bottom plates, etc.) are also made with devices that cut
connected together and with the main protection conductor. Ω 0.1 into the painted surface:
is the maximum resistance value allowed for this circuit. - clips
Electrical continuity in System pro E power switchboards is - 1/4-turn screws
automatically guaranteed by the screws and bolts and by the way - self-threading screws
the structure assembly is engineered. In addition, the connections - screws + nuts with sharp-toothed washers
can be made using the earthing pins on the external covers.
It is obligatory to use a braid for the earth connection in the case
The panels are earthed by means of the fastening screw, as of movable metal parts (doors, swing frames or removable panels)
required by standard IEC 61439-1 (part 8.4.3.2.2) “Specifications that must support electrical components differing from class 2
for earthing continuity to protect against the consequences of (which, being fitted with double insulation, are not earthed).
faults within switchgear”: “b) For covers, doors, closing plates Electrical continuity in the case of front panels, is guaranteed in
and similar, the ordinary connections with metal screws and metal the closed position by the special shape of the hinge (ABB patent),
hinges are considered sufficient for electrical continuity so long as always supplied even in the absence of connection via conductor.
electrical devices that exceed the low voltage limits (ELV) are not
installed on them”. To achieve this: Earthing braid is supplied on request for the electrical components
- only and exclusively use the screws and accessories supplied installed on the door, as well as for the passage of cables
7 with the components from communicating or low power circuits: analog, digital and
- comply with the assembly instructions given in the manuals telecommunication cables.
The proposed solutions have been tested and no additional Since the internal parts and the circuit-breaker assembly kits are
earthing braid is required. made of unpainted galvanized steel, continuity is guaranteed
without any additional earthing braid.
The paint reduces the electrical continuity of the assembled parts. The earth conductor must be properly sized in relation to the
To assure electrical continuity, use screws with with toothed maximum operating current, as shown in the following table
washers that cut into the paint or, alternatively, earthing braid. defined by Standard IEC 61439-1.
To assure electrical continuity, the mechanical assemblies (front

Calculation of protection conductor PE
Standard IEC 61439-1-2 contain the methods for calculating the section of the protection conductor PE, which must be sized to
withstand the thermal and dynamic components of the fault currents.
The following conditions must be ascertained when choosing the position in which the bar is to be fixed:
- the bar must be connected straight to the earthed parts of the switchboard (structure);
- the bar must be connected in an easily accessible position.
Use the values in the table for sizing taken from Standards IEC 61439-1-2.
S (mm2) Sp (mm2)
S ≤ 16 S
16 < S ≤ 35 16
35 < S ≤ 400 S/2
400 < S ≤ 800 200
S > 800 S/4

System pro E power
Equipotentiality
Conductive parts of a device, which cannot be connected to the protection circuit with their own means of connection, must be
connected to the protection circuit of the apparatus through the equipotentiality of the protection. This is done by means of a protective
bonding conductor, the section of which must be chosen in accordance with the table below.
Rated service voltage Minimum section of the protective bonding conductor

Ie (A) (mm2)
Ie ≤ 20 S
20 < Ie ≤ 25 2,5
25 < Ie ≤ 32 4
32 < Ie ≤ 63 6
63 < Ie 10
S = section of the line conductor (mm )

2
Conductor PEN
The section of the PEN conductors of an apparatus must be determined in the same way as the neutral conductor (N).
7 10mm2 is the minimum section of a copper conductor.
The PEN conductor does not need to be insulated.
Structure parts must not be used as a PEN conductors. However, the copper or aluminium assembly tracks can be used as PEN
conductors.
For conductors that are not made of copper, equivalent conductivity sections are used instead of the sections above and may require
larger terminals.

Mechanical shock resistance IK
The IK is expressed in Joule in compliance with the requirements of IEC 62262.
IK 0 Not protected IK 06 0,25 kg

Impact energy in
Joule 1.00
400mm
IK 01 0,25 kg
Impact energy in IK 07 Impact energy in
0,50 kg
56mm
Joule 0.140 Joule 2.00
400mm
IK 02 Impact energy in IK 08 Impact energy in 7

0,25 kg 1,7 kg
Joule 0.200 Joule 5.00
80mm
300mm
IK 03 0,25 kg
Impact energy in IK 09 5 kg
System pro E power
Joule 0.350 Glass door
140mm
200mm
Impact energy in
Joule 10.00
IK 04 0,25 kg
Impact energy in IK 10 5 kg System pro E power
Joule 0.500 Blind door
200mm
400mm
Impact energy in
Joule 20.00
IK 05 0,25 kg
Impact energy in
280mm
Joule 0.700

System pro E power
IP protection class
1st DIGIT: protection against solid objects 2nd DIGIT: Protection against liquids
0 No protection 0 No protection
1 Protected against solid objects larger 1 Protected against vertically dripping water
50mm (accidental contact with the hands) (condensation)
2 Protected against solid objects larger 2 Protected against water dripping at an angle
than 12mm (fingers) up to 15° from the vertical
7
3 Protected against solid objects larger 3 Protected against rain falling at an angle up
than 2.5mm (tools, wires) to 60° from the vertical
4 Protected against solid objects 4 Protected against water splashing from all
larger than 1mm directions
5 Protected against dust 5 Protected against jets of water sprayed from

(no harmful deposits) all directions
6 Totally protected against 6 Protected against jets of water similar to

dust waves
1st digit defined by Standards 61439-1-2 (Ref. sect. 10.3). 7 Protected against the effects of temporary
immersion
8 Protected against the effects of continuous

immersion
2a digit defined by Standards 61439-1-2 (Ref. sect. 10.3).

IP protection class
Protection against ingress of solid objects Protection against ingress of water
1st
Brief Full 2nd Brief Full
characteristic description description characteristic description description
digit digit
0 Not protected No particular protection 0 Not protected No particular protection
is envisaged is envisaged
1 Protected against A large area of the human 1 Protected against Drops of water falling
solid objects larger body, for example a hand dripping vertically must not produce
than 50mm (however, voluntary protection water harmful effects
is not envisaged) or solid 2 Protected against Drops of water falling
objects larger than 50mm water dripping vertically must not produce
in diameter must not at a maximum harmful effects when the
be able to angle enclosure is tilted at any
penetrate of 15° angle up to 15°
from its normal
2 Protected against The fingers or similar objects position
solid objects meas- measuring 80mm or solid 3 Protected against Water falling as a spray at
uring objects more than 12mm rainfall any angle up to 60° from the
in diameter must not be able to vertical shall
penetrate have no harmful
Protected against Tools, wires, etc., more than effects
3
solid objects meas- 2.5mm in diameter or
7
4 Protected against Water splashing against the enclosure
uring thickness or solid objects splashing water from any direction shall have no harm-
more than 2.5mm more than 2.5mm in diameter ful effects
must not be able to penetrate
5 Protected against Water projected by a
water jets nozzle from any direction
4 Protected against Wires or flat cables more shall have no harmful effects
solid objects meas- that 1.0mm thick or solid 6 Protected against Waves or powerful water
uring objects more than 1.0mm in waves jets shall not penetrate the
more than 1.0mm diameter must not be able enclosure in harmful
to penetrate quantities
7 Protected against Ingress of water in harmful
5 Protected against Penetration of dust is not the effects quantities shall not be
dust totally excluded but the quantity of temporary possible when the enclosure
that may penetrate is not immersion is immersed in water under
sufficient to impair the correct defined conditions of
operation of the material pressure and time
8 Protected against The equipment is suitable for
6 Totally protected No dust penetration the effects continuous immersion under condi-
against dust is permitted of continuous tions which shall be specified by the
immersion manufacturer

System pro E power
Connection examples - Unifix H

Unifix H frame with 400A busbars 24 and 36 DIN modules
Busbars supplied from above by means of a 4P feeder module Power supply by means of circuit-breaker supplied from
installed laterally above
ED2531 ED2549 ED2556
In = 320A max ED2191
ED2549 ED2531 ED2564
ED2209 ED2191
ED2556
N N
ED2845 ED2564
L1 L1
T T
L2 L2
L3 N N L3
N N
L1 L1
T T T
L2 L2
N N N
L3 L3
N N
L1 L1
T
L2 L2
L3 N L3
7
Busbars supplied from below by means of a 4P feeder module Power supply by means of circuit-breaker supplied from
installed laterally below
ED2531 ED2531 ED2531
ED2549 ED2549 In = 400A max ED2549
ED2191 ED2556 ED2191
ED2556 ED2556
ED2564
ED2564 ED2564
ED2845
N N N N
on
L1 L1 L1 L1
T T TEST
T T T
TEST
L2 L2 L2 L2
N N N N N
L3 L3 L3 L3
Busbars supplied from above by means of a 4P feeder module Covers for IP 20 protection class
installed centrally
ED2531 ED2407
In = 400A max ED2549
ED2191
ED2556
ED2564
N N
L1 L1
T
L2 L2
L3 N L3
N N
on
L1 L1
TEST
T T T
TEST
L2 L2
ED2407
N N N
L3 L3

Connection examples - Unifix L
Unifix L frame with 100A busbars 12/18/24 DIN modules
Two different single-phase circuits on a single DIN rail Busbars supplied by means of terminals installed
with 24 modules centrally
ED3104
ED3103
In 100 A max
ED3102
ED3082
ED2993 ED2993 ED3101
T T
T
N N
N
7
Example of main and branched power supply Busbars supplied from above by means of terminals installed
laterally
ED3104
ED2969
ED3103
ED3102
In = 80 A max
ED3101
T T T
N N N
ED3082
ED3132 ED2944
(L=350mm)
ED2993
T T T T
N N N N
Busbars supplied by means of cable terminal under the head of Busbars supplied directly by means of feeder module
the circuit-breaker's terminal and branching with parallel module (supplied without cables) and branching by means of feeder module
In = 100 A max ED3101 ED2969
ED3405
(L=400mm) ED3102
ED3103
ED3104 T T T T T
N N N N N
ED3132
(L=350mm) ED2969
T T T T
N N N N

System pro E power
Configuration examples
2000x800x300mm (HxLxP) structure with H=100mm plinth, internal cable compartment, IP65 protection class. 1000A vertical
busbar system installed at the side of the cable compartment. T6 main circuit-breaker fixed vertically. Fixed frame. T4 circuit-
breaker kit fixed horizontally, No. 3 XT1 fixed horizontally.
Order
Quantity code Description Reference chapter
7 1 PUPM2000 No.4 galvanized sheet metal uprights H=2000mm Structure
1 PUCM2000 No. 4 galvanized sheet metal cross-pieces L=800mm Structure
1 PCFM0800 No. 4 galvanized sheet metal cross-pieces L/D=300mm Structure
1 PCFM0300 No. 4 galvanized sheet metal plinth angle pieces H=100mm Structure
1 PPAM0100 No. 2 front/rear plinth flanges H=100mm L=800mm Structure
1 PPFM1080 No. 2 side plinth flanges H=100mm L/D=300mm Structure
1 PPFM1030 Blind Top/Bottom IP65 L=800mm d=300mm Structure
1 PTBB8036 Open Top/Bottom IP65 L=800mm d=300mm Structure
1 PTBO8030 Incoming cable flange 800x300mm Structure
1 PFCF8030 External cover IP65 H=2000mm L=800mm Structure
1 PPEB2086 External cover IP65 H=2000mm L/D=300mm Structure
2 PPEB2036 Blind door for int.cable comp. H=2000mm L=200mm Structure
1 PDCB2020 Glass door IP65 H=2000mm L=800mm Structure
1 PDLG2062 Upright for cable comp. in galv. sheet metal H=2000mm Structure
1 PFPF2060 Fixed frame for panels H=2000mm L=600 Internal kits
1 PVCT6401 Kit with 3-4P T6 fixed vertical installation L=600mm Internal kits
1 PHCT4406 Kit with 3-4P T4 fixed horizontal installation L=600mm Internal kits
3 PHCX1401 Kit with 3-4P XT1 fixed horizontal installation L=600mm Internal kits
1 PPFB1560 Flat blind panel H=150mm L=600mm Internal kits
8 PBFC4005 Flat copper bar 40x5 L=1750mm Main distribution systems
2 PCRM0238 No. 2 galvanized sheet metal cross-pieces L=238mm Main distribution systems
2 PBHB1125 No. 24 busbar insulating supports L=50mm Main distribution systems
2 PTRN1951 No. 10 nylon tie rods L=195mm for In<4000A Main distribution systems
1 PBBV0008 No. 8 busbar plates vertical side Main distribution systems

1800x600x300mm (HxLxP) structure without plinth, IP65 protection class. 630A vertical busbar system installed at the rear of
the structure. T5 main circuit-breaker fixed vertically. Kit with No.2 XT2 circuit-breakers fixed vertically.
T T T
T T T
Order
1 PUPM1800 No. 4 galvanized sheet metal uprights H=1800mm Structure
7
1 PCFM0600 No. 4 galvanized sheet metal cross-pieces L=600mm Structure
1 PTBB6030 Blind Top/Bottom IP40 L=600mm d=300mm Structure
1 PBWP6030 Internal bottom IP40 L=600mm D=300mm Structure
1 PPEB1860 External rear cover IP40 H=1800mm L=600mm Structure
2 PPEB1830 External side cover IP40 H=1800mm L/D=300mm Structure
1 PDLG1860 Glass door IP40 H=1800mm L=600mm Structure
1 PFPF1860 Fixed frame for panels H=1800mm L=600 Internal kits
1 PVCT5406 Kit with 3-4P T5 fixed+vertical (400/630A)mrd L=600mm Internal kits
2 PVCX2401 Kit with 3-4P XT2 fixed vertical installation L=600mm Internal kits
2 PDRS0600 Standard DIN rail L=600mm Internal kits
2 PPMF2060 Panel with 24 DIN modules H=200mm L=600mm Internal kits

System pro E power
2000x800x500mm (HxLxP) structure with H=100mm plinth, internal cable compartment, IP65 protection class. 1600A vertical
busbar system installed at the side of the structure. T7 main circuit-breaker fixed vertically. Swing frame. Horizontal removable
T6 kit, horizontal removable T5, horizontal removable XT4.
Order
7 1 PUPM2000 No. 4 galvanized sheet metal uprights H=2000mm Structure
1 PPAM0100 No. 4 galvanized sheet metal plinth angle pieces H=100mm Structure
1 PPFM1080 No. 2 front/rear plinth flanges H=100mm L=800mm Structure
1 PPFM1050 No. 2 side plinth flanges H=100mm L/D=500mm Structure
2 PTBB8056 Blind Top/Bottom IP65 L=800mm d=500mm Structure
1 PPEB2086 External cover IP65 H=2000mm L=800mm Structure
2 PPEB2056 External cover IP65 H=2000mm L=500mm Structure
1 PDCB2020 Blind door for int.cable comp. H=2000mm L=200mm Structure
1 PUCM2000 Upright for cable comp. in galv. sheet metal H=2000mm Structure
1 PCCM0500 No. 2 galvanized sheet metal cross-pieces VC D=500mm Structure
2 PUKI2000 Swing frame for panels H=2000mm L=600 Structure
1 PFPS2060 Int. kit intermediate upright H=2000mm Structure
1 PVCT7419 Kit with 3-4P T7 fixed vertical installation L=600mm Internal kits
1 PHCT6410 Kit with 3-4P T6 removable horizontal installation L=600mm Internal kits
1 PHCT5414 Kit with 3-4P T5 removable (400A) horizontal installation L=600mm Internal kits
1 PHCX4410 Kit with 3-4P XT4 removable horizontal installation L=600mm Internal kits
1 PCBS1560 Blind compartment H=150mm W=600mm Segregations
1 PPVS2450 No.2 lateral segregation cell H=450mm Segregations
4 PSHS1906 Horizontal shelf W=600mm Segregations

2000x600x700mm + 2000x1000x700 (HxLxP) structure with H=100mm plinth, L400mm cable compartment inside the
L=1000mm structure, IP40 protection class. 2500A horizontal busbar system at any height in the unit L=600mm and vertically
on the side of the structure L=1000mm. E2.2 removable main circuit-breaker fixed vertically. Fixed frame. Kit with horizontal
removable 4-pole T7, horizontal removable 4-pole T6, 2 horizontal removable XT2.
Order
2 PUPM2000 No. 4 galvanized sheet metal uprights H=2000mm Structure 7
2 PCFM0700 No. 4 galvanized sheet metal cross-pieces D=700mm Structure
2 PPAM0100 No. 4 galvanized sheet metal plinth angle pieces H=100mm Structure
1 PPFM1070 No. 2 side plinth flanges H=100mm D=700mm Structure
1 PTBB6070 Blind Top/Bottom IP40 L=600mm D=700mm Structure
1 PTBO6070 Open Top/Bottom IP65 L=600mm D=700mm Structure
2 PTBB1070 Blind Top/Bottom IP40 L=1000mm D=700mm Structure
1 PPEB2060 External cover IP30/40 H=2000mm L=600mm Structure
1 PPEB2010 External cover IP30/40 H=2000mm L=1000mm Structure
2 PPEB2070 External cover IP30/40 H=2000mm D=700mm Structure
1 PUCM2000 Galvanized sheet metal cable uprights H=2000mm Structure
1 PCCM0700 2 galvanized sheet metal cross-pieces D=700mm Structure
1 PDCB2040 Blind door for int.cable comp. H=2000mm L=400mm Structure
1 PSBS0040 Kit for joining side structures IP40 Structure
5 PUKI2000 Internal kit intermediate upright H=2000mm Structure
2 PFPF2060 Fixed frame for panels H=2000mm L=600 Structure
1 PVCE2450 Kit with vertical 3-4 pole Emax E2.2 600x600 Internal kits
2 PHCX2410 Kit with 3-4P XT2 removable horizontal installation L=600mm Internal kits
1 PPMB6060 Blind mounting plate H=600mm W=600mm Internal kits
1 PBBH0004 No. 4 busbar plates at all heights Main distribution systems
CONTINUES

System pro E power
Order
2 PSHW5061 Segregation for Form 2a-3a T7 withdrawable H=500mm W=600mm Segregations
2 PSVS0055 Segregations for horizontal breakers terminals H=500mm D=700mm Segregations
2 PCVS5060 Cubicles Form 4b T7 withdrawable H=500mm W=600mm Segregations
5 PCBS2060 Blind Compartment H=200mm W=600mm Segregations
5 PPBS0200 Lateral segregation for blind compartment H=200mm Segregations
1 PSVS0207 Rear segregation for blind compartment H=200mm Segregations
1 PPBS0300 Lateral segregation for blind compartment H=300mm Segregations
1 PSVS0307 Rear segregation for blind compartment H=300mm Segregations
2 PPVS2250 N.2 lateral cell segregations H=250mm Segregations
2 PSVS2570 Segregation for horizontal breakers terminals H=250mm D=700mm Segregations
2 PCVS1256 Cubicles P1 for breakers kit H=250mm W=600mm Segregations
2 PRVS1061 Rear segregation for structure busbars side H=1000mm W=600mm Segregations
1 PPVS2600 No.2 lateral cell segregations H=600mm Segregations
1 PSVW6062 Segregation 2a-3a E2.2 withdrawable H=600mm W=600mm Segregations
1 PSHW6072 Horizontal segregation 3b E2.2 withdrawable L=600mm D=700mm Segregations
1 PRVS3060 Rear segregation H=300MM W=600MM for structure without intermediate upright Segregations
2 PMCS3070 No.2 lateral connection modules H=300mm D=700mm Segregations
2 PBMC0002 No.2 fixing brackets for connection modules Segregations
2 PLVS4072 Rear lateral segregation for compartment H=400MM D=700MM for structure with rear Segregations
intermediate upright
1 PRVS7060 Segregazione verticale posteriore H=700MM W=600MM for structure without rear inter- Segregations
7 mediate upright
1 PRVS1060 Segregazione verticale posteriore H=1000MM W=600MM for structure without rear Segregations
intermediate upright
7 PSHS1906 Horizontal shelf W=600mm Segregations

System pro E power
Overall dimensions
Frame 8/2
Internal cable compartment 8/3
Intermediate upright 8/3
Adjacent structures 8/3
External covers 8/4
Internal kit 8/7
Main distribution systems 8/11
Segregations 8/16

System pro E power
Overall dimensions
Frame
Front Side
B C Height measurements (mm)
B1 C1 A A1
1913 1804
2113 2004
Width measurements (mm)

B B1 B2 B3 B4 B5 B6 B7 B8
349 254 148 287 225 194 271 348 226
399 304 198 337 375 244 321 398 276
499 404 298 437 475 344 421 498 376
599 504 398 537 575 444 521 598 476
699 604 498 637 675 544 621 698 576
849 754 648 787 825 694 771 848 726
899 804 698 837 875 744 821 898 776
A A1 47.5
1099 1004 898 1037 1075 944 1021 1098 976
1349 1254 1148 1287 1325 1194 1271 1348 1226
Depth measurements (mm)

C C1 C2 C3 C4 C5 C6 C7 C8
8 299 204 98 237 275 144 221 298 176
399 304 198 337 375 244 321 398 276
599 504 398 537 575 444 521 598 476
47.5 799 704 598 737 775 644 721 798 676
999 904 798 937 975 844 921 998 876
100
100 B2 100 100 C2 100
Bottom Fixing on floor
119.5
119.5
25
C4 C3 C7 C6 C5 C8
14
B5 100
38.5
2.5
Ø1
38.5
B8
100
B3 B6
B4 B7
> The measurements are given in millimeters

Internal cable compartment Intermediate upright
Front Side
A
A1
A A1 D D1
699 604 200 404
899 804 200 604
400 404
1099 1004 200 804
400 604
D D1 179
250
Overall dimensions for several adjacent structures

Front Side Total width calculation
1 1 1 1
8.5 B B B B B 8.5 C 1- add 1mm to the width of the columns (B+1) + (B+1)....
2- add 17mm for the 2 side panels (8.5+8.5=17mm)
3- subtract 1mm from the total (-1mm)
Example
349 299 (699+1) + (899+1) + (699+1) +17 - 1 = 2.316
399 399 8.5 1 1 8.5
499 599
599 799
699 999 699 899 699
849
899
1099
Total depth calculation

Add 48mm to the depth of the structure (C),
corresponding to the front and rear covers.
C (depth of the structure) +

48mm (front and rear covers including handle)

System pro E power
Overall dimensions
External covers
Glass doors
Front Side Rear
A B 46 70
107 112 C 112
75 79 C1
89 70
1904
2104
89 70
70
A B C C1
Top 494 - - -
17 594 - - -
694 - - -
4 15 844 - - -
894 894 307 -
14
1094 1094 307 507

External covers
Blind doors
Front Rear Side
344
A A 46
394
75 79 130 130
70 49.5 49.5
70 70
54.5
1904
2104
Ø5
25
8
127
70 70
B
70 70
A B
Top 494 250
14 14
594 350
15 15 13
694 450
844 600
17 17 894 650
1094 850

System pro E power
Overall dimensions
External covers
Rear, side panels
A B C C
75 75
1904
2104
Rear panels Side panels
A B C A B C
339 169.5 289 144.5
389 194.5 389 194.5
489 244.5 589 75
589 75 789 75
8
689 75 989 75
839 75
54.5 889 75
75 75 1089 75
54.5 54.5
Top
15

Internal kit
Mounting Plates
Heigh 150mm A B C
A
363 344 146
B 563 544
763 744
19
23
Heigh ≥ 200mm
A B C
A
381 347 196
581 547
B
781 747
8
981 947
381 347 246
581 547
781 747
981 947
381 347 296
C
581 547
781 747
981 947
381 347 346
581 547
19 781 747
981 947
24
381 347 396
581 547
781 747
981 947
381 347 446
581 547
781 747
981 947
381 347 496
581 547
781 747
981 947
381 347 596
581 547
781 747
981 947

System pro E power
Overall dimensions
Internal Kit
Flat blind panels =
48
14.3 98
=
A B
48 343
98 543
148 743
198 943
A
248
298
49 398
498
12 598
B
Ventilated panels
=
48
14.3 98
=
A B
19
10 48 343
98 543
asole passo 10
8 A
148 743
198 943
248
49 10 298
19 398
71.5 50 50 step buttonholes 498

50 71.5
12 598
B
Panels Modular DIN Rail
343-543-743
14.3
198 47
=
49
50.5
99
47
47
298 298
199
47
50.5
12
46.5 250-450-650 46.5 46.5 250-450-650 46.5

Internal kit
Panels for square measuring instruments
Panel 2 instruments
= 130 =
14.3 A B C
198 543 68
C C = 92
198 743 68
A C C 92
=
58.7
= 300 =
12
B
Panel 4 instruments
D E E F D
14.3 A B C D E F
198 543 68 96.5 100 150
C = 198 743 68 196.5 100 150
92 121.5 150 200
A C
8
=
58.7
= =
12
B
Recessed blind panels A B C

B 198 343 30
14.3
80
398 30
598 30
198 543 30
A 80
398 30
58.7 598 30
198 743 30
80
C
C
12 398 30
598 30
Panels for ATS 022 devices mounting on DIN Rail * 198 943 80
14.3
76.5
298 145
58.7 76.5
12
123-223-323 97 123-223-323
343-543-743
* Not available for sale

System pro E power
Overall dimensions
Internal kit
Useful space inside the switchgear
USEFUL SPACE
FOR BARS
702
902
USEFUL SPACE 202
FOR BARS 302
502 A
702
902
B
A
To find the useful space available for the installation of the busbars, according to depth of the structure, subtract the depth of the
breaker (A or B) depending on the version shown in the following table.
Tmax T - Tmax XT - Emax 2 E1.2
Execution F F-I F - I-MO F - MO F - RC F - RHD
Terminals Front (A) Rear (B) Front (A) Rear (B) Front (A) Rear (B) Front (A) Rear (B) Front (A) Rear (B) Front (A) Rear (B)
Circuit-breakers Depth circuit breaker A (mm)
XT1-XT3 74 179 139 179 237* 277* 172 277 74 179 108 213
86 191 151 191 237* 277* 172 277 86 191 120 225
8 XT2-XT4
T4 107 212 172 212 287* 327* 222* 327* 107 212 140,5 245,5
T5 107 242 172 242 287* 357* 222* 357* 107 242 140,5 275,5
T6 107 180 172 180 287* 295* 222* 295* 107 180 140,5 213,5
T7 171 230 171 230 171 230 171 230 171 230 184 243
E1.2 157 216 157 216
Execution P (A) (B) P - I (A) (B) P - I-MO (A) (B) P - MO (A) (B) P - RHD (A) (A)
XT1 124 204,5 189 204,5 287* 302,5* 222* 302,5* 158 238,5
XT2 136 216,9 201* 216,9* 287* 302,9* 222* 302,9* 170 250,9
XT3 124 206,9 189 206,9 287* 304,9* 222* 304,9* 158 240,9
XT4 136 218,9 201* 218,9* 287* 304,9* 222* 304,9* 170 252,9
T4
T5(1) 157 231,25 222* 231,25* 337* 346,25* 272* 346,25* 190,5 264,75
T5(2) 157 231,25 272* 346,25* 190,5 264,75
Execution W (A) (B) W - I (A) (B) W - I-MO (A) (B) W - MO (A) (B) W - RHD (A) (B)
XT2 170 250,9 235* 250,9* 287* 302,9 222* 302,9* 170 250,9
XT4 170 252,9 235* 252,9* 287* 304,9 222* 304,9* 170 252,9
T4
T5(1) 190,5 264,75 255,5* 264,75* 337* 346,25* 272* 346,25* 190,5 264,75
T5(2) 190,5 264,75 272* 346,25* 190,5 264,75
T6 190,5 271 255,5* 271* 337* 352,5* 272* 352,5* 190,5 271
T7 251 297 251* 297* 251* 297* 251* 297* 251* 297*
E1.2 251 300 251 300
(1)
Tmax T5 400A (2)
Tmax T5 630A *Breakers with recessed mounting plate.
Emax 2 Key:
Accessorized or not accessorized, only rear terminals.
F fixed P - RC plug-in with residual current
Execution F W F-I fixed interlocked P - RHD plug-in with Direct Rotary Handle
Circuit-breakers Depth circuit breaker A (mm) F - I-MO fixed interlocked motor-operated W withdrawable
F - MO fixed motor-operated W-I withdrawable interlocked
E2.2 291 405 F - RC fixed with residual current W - I-MO withdrawable interlocked motor-operated
E4.2 291 405 F - RHD fixed with Direct Rotary Handle W - MO withdrawable motor-operated
F&F-I fixed and fixed interlocked W - RC withdrawable with residual
E6.2 291 405 P plug-in current
P-I plug-in interlocked W - RHD withdrawable with Direct Rotary Handle
P - I-MO plug-in interlocked motor- W&W-I withdrawable and withdrawable
operated interlocked

Internal kit
Blind mounting plates
107
44÷159 74÷189
Flat Recessed Flat

panel panel
56 86 56 panel

Shaped profile busbars
PBSC0400 PBSC1000
In 400A In 1000A
10 1750 10 1750
8
= 18.5
15 8.6 30
15 8.6
=
3.5 15 21.4 30 67
PBSC0630
In 630A 15 8.6
1750
10
18.5
15 8.6 35 11.5
3.5 PBSC1250
In 1250A
10 1750
PBSC0800 20
In 800A
1750
10 15 8.6
= 30 70
15 8.6 45
15 8.6
=
20
3.5

System pro E power
Overall dimensions

Shaped profile busbars
PBSC1600 PBSC2500
In 1600A In 2500A
10 1750 10 1750
32.5
37.5
15 8.6
15 8.6
30 95
30 105
15 8.6
15 8.6
32.5
37.5
8
PBSC2000
In 2000A
1750 15
10
37.5
15 8.6
30 105
15 8.6
37.5
15

Flat busbars
Copper busbars
A 1750
Code A B
12.5 25 Ø6.5 12.5 12.5
PBFC2005 5 20
= PBFC2505 5 25
B
PBFC4005 10 30
=
PBFC8005 5 40
PBFC3205 5 32
1750
12.5 25 Ø10.5 12.5
A
12.5
Code A B
B PBFC1005 5 100
PBFC3010 5 80
PBFC5005 5 50
12.5 PBFC6305 5 63
A 1750
Code A B 8
PBFC1001 10 100
PBFC1201 10 120
PBFC1601 10 160
B PBFC2001 10 200
PBFC4010 10 40
PBFC5010 10 50
PBFC6010 10 60
PBFC8010 10 80
A 1750
Cuponal busbars
Code A B
PBFA2005 5 20
PBFA2505 5 25
B PBFA3005 5 30
PBFA4005 5 40
PBFA5005 5 50
PBFA6005 5 60
PBFA8005 5 80
PBFA4010 10 40
PBFA5010 10 50
PBFA7510 10 75
PBFA8010 10 80
PBFA1001 10 100
PBFA1201 10 120

System pro E power
Overall dimensions

Linear busbar rails
PBHB1125 PBHB2145
55
50 75 10 55
55 10 5 55
10 5 10
56
56
39
39
PBHB3121
10
10
10
10
100 10 10
10
10 56
39
19 50/75/100 19
29.5
20÷200
29.5
10

Scaled busbar rails
38
58
78
98
20÷120
162.5÷204.5
172.5÷214.5
10 270
65 217
Tie rods 8
Nylon tie rods Stainless steel tie rods
A
195
A
Stainless steel tie rods 210
250
290
Crosspieces for insulating supports

Galvanzied Stainless
sheet metal steel A
PCRM0188 88
PCRM0238 238
PCRM0288 288
PCRM0338 PCRS0338 338
A
PCRM0388 PCRS0388 388
PCRM0438 PCRS0438 438
PCRM0488 488
PCRM0538 538
PCRM0588 PCRS0588 588
PCRM0638 PCRS0638 638
PCRM0688 688
PCRM0738 738
PCRM0788 PCRS0788 788
PCRM0888 PCRS0888 888
PCRM0988 PCRS0988 988
PCRM1238 1238
PCRM2013 PCRS1238 2013

System pro E power
Overall dimensions
Segregations
Form 4b segregations
Segregations rear mounting positions
Assembly position P0
A B C
599 244 310
699 244 510
999 244 710
C
8 A B C
599 364 190
699 364 390
C
999 364 590
A B C
599 434 120
C 699 434 320
999 434 520

System pro E power
List of codes

System pro E power
List of codes
Code Page Weight KG Code Page Weight KG Code Page Weight KG Code Page Weight KG
6652 5/40 0,6 AD1077 5/43 1,05 ED2407 5/38 1,56 ED3355 5/39 0,40
7241 5/41 0,58 AD1080 5/45 0,25 ED2531 5/37 0,97 ED3363 5/39 0,50
7242 5/41 0,7 AD1081 5/45 0,25 ED2549 5/37 0,97 ED3371 5/39 0,60
7243 5/41 0,93 AD1083 5/45 0,25 ED2550 5/37 0,88 ED3405 5/39 3,70
7244 5/41 1,17 AD1086 3/44 3,51 ED2551 5/37 1,60 ED3413 5/39 4,80
7245 5/41 1,67 AD1086 3/44 3,51 ED2552 5/37 1,54 ED3439 5/39 7,80
7246 5/41 2,81 AD1101 3/44 0,05 ED2553 5/37 1,54 EV0036 3/43 0,20
7247 5/41 3,44 AD1102 3/44 0,02 ED2554 5/37 1,54 EV0037 3/43 0,35
7855 5/40 0,76 AD1103 3/44 0,02 ED2556 5/37 1,04 EV0042 3/44 0,25
1SL9037A00 5/40 0,76 AD1104 3/44 0,02 ED2557 5/37 - EV0103 2/40 0,50
1SL9816A00 5/40 0,79 AD1600 3/44 0,24 ED2558 5/37 - EV0104 2/40 0,50
1SL9817A00 5/40 0,97 AD1800 3/44 0,36 ED2559 5/37 - EV0114 2/36 0,95
1SL9818A00 5/40 1,15 AD3301 3/45 0,15 ED2560 5/37 - EV0116 2/36 0,95
1SL9819A00 5/40 1,52 AD3302 3/45 0,15 ED2564 5/37 0,95 EV0117 2/37 0,75
1SL9820A00 5/40 1,03 AD3303 3/45 0,15 ED2572 5/37 1,04 EV0119 2/37 0,20
1SL9836A00 5/40 1,07 AD3304 3/45 0,15 ED2590 5/37 0,97 EV0121 2/37 0,20
1SL9838A00 5/40 1,25 AD3305 3/45 0,15 ED2598 5/37 1,07 EV0123 2/37 0,20
1SL9839A00 5/40 1,43 AD3306 3/45 0,15 ED2606 5/37 1,16 EV0124 2/37 0,20
1SL9840A00 5/40 1,8 AD3307 3/45 0,15 ED2654 5/37 0,80 EV0125 2/37 0,13
1SL9841A00 5/40 2,44 AD3308 3/45 0,15 ED2662 5/37 0,80 EV0126 2/37 0,13
1SL9842A00 5/40 2,85 AP6000 3/43 0,01 ED2670 5/37 0,97 EV0127 2/37 0,13
1SL9860A00 5/40 1,09 BF1602 5/44 2,70 ED2720 5/37 1,20 EV1008 2/38 0,04
1SL9861A00 5/40 1,13 BF2502 5/44 4,20 ED2738 5/37 1,20 EV1036 2/38 0,04
1SL9862A00 5/40 1,31 BF4002 5/44 3,00 ED2746 5/37 1,29 EV1037 2/38 0,04
1SL9863A00 5/40 1,49 BF4012 5/44 6,50 ED2753 5/37 1,17 EV1039 2/38 0,04
1SL9864A00 5/40 1,86 BF6302 5/44 12,50 ED2845 5/38 0,58 EV1050 5/42 6,88
1SL9865A00 5/40 2,5 BF8002 5/44 19,10 ED2852 5/38 0,58 EV1051 5/42 1,00
1SL9866A00 5/40 2,91 BS3250 5/44 1,60 ED2894 5/37 0,90 EV1056 5/42 0,33
9 1SL9880A00 5/41 0,14 BS5050 5/44 1,80 ED2902 5/37 0,84 EV1058 5/42 0,58
1SL9886A00 5/41 0,11 BS6350 5/44 2,25 ED2910 5/37 0,87 EV1075K 2/38 0,20
1SL9887A00 5/41 0,14 ED0001 5/38 0,22 ED2928 5/37 0,92 EV1090 5/42 0,46
1SL9893A00 5/41 0,01 ED0002 5/38 0,28 ED2936 5/38 0,58 EV1091 5/42 0,88
1SL9904A00 5/40 0,31 ED0003 5/38 0,29 ED2944 5/39 2,15 EV1092 5/42 0,55
1SL9907A00 5/41 0,15 ED0004 5/38 0,29 ED2951 5/39 3,34 EV1093 5/42 0,55
1SL9910A00 5/41 0,23 ED0025 5/39 11,56 ED2961 5/39 0,40 EV1100 2/40 1,15
1SL9911A00 5/41 0,3 ED0026 5/39 8,00 ED2962 5/39 0,60 EV1101 2/40 1,28
1SL9912A00 5/41 0,38 ED2183 5/37 3,10 ED2969 5/39 4,50 EV1110 3/43 2,74
1SL9913A00 5/41 0,53 ED2191 5/37 4,10 ED2977 5/39 6,70 EV1110 5/43 2,74
1SL9914A00 5/41 0,68 ED2209 5/37 1,45 ED2985 5/39 1,14 EV1111 3/43 0,68
1SL9915A00 5/41 0,83 ED2217 5/38 2,04 ED2993 5/39 1,65 EV1112 3/43 2,74
AA1560 2/38 0,02 ED2225 5/38 2,10 ED3009 5/39 2,32 EV1113 5/43 0,13
AA1570 2/38 0,03 ED2233 5/38 2,30 ED3017 5/39 2,85 EV1119 5/42 3,60
AA6200 2/38 0,02 ED2241 5/38 1,70 ED3025 5/39 4,05 EV1120 5/42 4,50
AA8004 2/38 0,01 ED2258 5/38 2,40 ED3033 5/39 0,51 EV1121 5/42 8,85
AD1004 5/45 0,55 ED2266 5/38 2,70 ED3041 5/39 0,44 EV1122 5/42 2,44
AD1006 5/45 0,55 ED2274 5/38 2,70 ED3058 5/39 0,38 EV1123 5/42 2,49
AD1007 5/45 0,25 ED2282 5/38 2,20 ED3066 5/39 0,51 EV1124 5/42 2,77
AD1009 3/44 0,09 ED2290 5/38 3,00 ED3082 5/39 1,48 EV1125 5/42 2,77
AD1009 3/43 0,09 ED2308 5/38 3,18 ED3090 5/39 3,36 EV1135 3/45 0,24
AD1027 5/45 0,69 ED2316 5/38 3,48 ED3101 5/39 0,30 EV1136 3/45 0,16
AD1028 5/45 0,31 ED2324 5/38 2,76 ED3102 5/39 0,30 EV1137 3/45 0,24
AD1029 5/45 0,41 ED2332 5/38 3,10 ED3103 5/39 0,30 EV1150 5/45 0,10
AD1030 5/45 0,44 ED2340 5/38 3,00 ED3104 5/39 0,30 EV1151 5/45 0,10
AD1031 5/45 0,52 ED2357 5/38 2,76 ED3108 5/39 0,30 EV1152 5/45 0,10
AD1034 5/45 2,00 ED2365 5/38 3,48 ED3116 5/39 0,35 EV1153 5/45 0,10
AD1037 3/43 0,35 ED2373 5/38 1,10 ED3124 5/39 0,50 EV1154 5/45 0,10
AD1053 5/45 2,95 ED2373 5/38 1,10 ED3132 5/39 1,98 EV1155 5/45 0,01
AD1058 2/38 0,01 ED2373 5/38 1,10 ED3272 5/39 0,61 EV1156 5/45 0,07
AD1075 5/45 0,55 ED2381 5/38 1,02 ED3280 5/39 0,61 EV2110 3/43 0,56
AD1076 5/45 0,25 ED2399 5/38 0,92 ED3298 5/39 0,57 EV2112 3/43 0,56

PBBT0008 5/36 0,79 PBPX3738 5/34 1,37 PBWP4020 2/29 1,64 PCCM0500 3/39 1,90
PBBU0008 5/35 - PBPX4631 5/33 1,56 PBWP4030 2/29 2,15 PCCM0600 2/19 2,20
PBCB0002 5/35 0,4 PBPX4738 5/34 1,30 PBWP4050 2/29 3,27 PCCM0700 2/18 2,54
PBBV0008 5/36 0,87 PBRB0004 2/21 0,56 PBWP4070 2/29 4,57 PCCM0700 3/39 2,54
PBFA1001 5/32 6,47 PBRF3453 5/45 0,32 PBWP4090 2/29 5,36 PCCM0800 2/19 2,60
PBFA1201 5/32 7,66 PBRL0002 2/39 1,49 PBWP5020 4/14 1,90 PCCM0900 2/18 3,08
PBFA2005 5/32 0,74 PBRN0002 5/36 0,40 PBWP5050 4/14 3,79 PCCM0900 3/39 3,08
PBFA2505 5/32 0,85 PBRP0002 5/36 0,50 PBWP5070 4/14 5,06 PCCM1000 2/19 3,42
PBFA5010 5/32 3,20 PBRR6040 3/42 - PBWP6050 4/32 4,65 PCCM2075 4/8 1,07
PBFA6005 5/32 2,13 PBSC0400 5/32 2,59 PBWP6070 2/29 6,36 PCCS0700 2/18 2,41
PBFA7510 5/32 4,88 PBSC0630 5/32 3,28 PBWP6070 4/32 6,36 PCCS0900 2/18 3,29
PBFA8005 5/32 2,73 PBSC0800 5/32 4,81 PBWP6090 2/29 8,12 PCFM0200 2/16 1,80
PBFA8010 5/32 5,08 PBSC1000 5/32 7,80 PBWP6090 4/32 8,12 PCFM0200 4/9 1,80
PBFC0160 5/44 2,66 PBSC1250 5/32 8,50 PBWP7520 4/14 2,66 PCFM0250 4/9 2,08
PBFC1601 5/31 25,00 PBTT4631 5/33 2,40 PBWP7590 4/14 9,60 PCFM0400 2/16 3,15
PBFC3205 5/31 2,38 PBTX1631 5/33 1,60 PBWP8070 2/29 8,31 PCFM0600 2/16 4,29
PBFC4010 5/31 6,50 PBTX3631 5/33 1,78 PBWP8090 2/29 10,25 PCFM0700 2/16 4,95 9
PBFC5010 5/31 8,00 PBUF0002 5/37 1,54 PCBS1010 6/25 2,53 PCFM0700 4/27 4,95
PBFC6010 5/31 9,50 PBUF0002 5/39 1,54 PCBS1040 6/25 1,12 PCFM0750 4/9 5,11
PBFC6305 5/31 4,46 PBWF0002 2/40 0,09 PCBS1060 6/25 1,50 PCFM0800 2/16 5,58
PBFC8005 5/31 5,85 PBWP1030 2/29 4,80 PCBS1080 6/25 2,08 PCFM0800 4/27 5,58
PBFC8010 5/31 12,50 PBWP1030 4/14 4,80 PCBS1510 6/25 3,17 PCFM0900 2/16 6,34
PBGT4738 5/34 1,40 PBWP1050 2/29 7,30 PCBS1540 6/25 1,44 PCFM0900 4/9 6,34
PBGT5738 5/34 2,20 PBWP1050 4/14 7,30 PCBS1560 6/25 1,99 PCFM0900 4/27 6,34
PBGX1738 5/34 1,00 PBWP1050 4/32 7,30 PCBS1580 6/25 2,62 PCFM1000 2/16 7,07
PBGX3738 5/34 - PBWP1070 4/14 9,60 PCBS2040 6/25 1,17 PCFM1000 4/27 7,07
PBHB1125 5/35 1,01 PBWP1090 2/29 12,12 PCBS2080 6/25 3,23 PCFM1250 4/9 9,50
PBHB1125 5/35 1,01 PBWP1090 4/14 12,12 PCBS2510 6/25 4,56 PCFS0200 2/16 -
PBHB2145 5/35 1,50 PBWP1090 4/32 12,12 PCBS2540 6/25 2,17 PCFS0300 2/16 2,50
PBHB3121 5/35 2,00 PBWP1230 4/14 - PCBS2560 6/25 2,86 PCFS0400 2/16 3,00
PBHS1125 5/35 0,25 PBWP1250 4/14 9,60 PCBS2580 6/25 3,72 PCFS0600 2/16 4,00
PBKT0002 2/39 1,66 PBWP1270 4/14 13,00 PCBS3010 6/25 5,16 PCFS0700 2/16 5,00
PBMC0001 4/8 - PBWP1290 2/29 9,03 PCBS3040 6/25 2,50 PCFS0800 2/16 5,40
PBMC0002 5/44 0,25 PBWP1290 4/14 9,03 PCBS3060 6/25 3,22 PCFS0900 2/16 6,00
PBMC0002 6/51 0,25 PBWP2520 4/14 1,20 PCBS3080 6/25 4,30 PCFS1000 2/16 7,00
PBPT4631 5/33 2,08 PBWP2530 4/14 1,40 PCBS5010 6/25 1,88 PCFS1250 2/16 8,00
PBPT4738 5/34 1,70 PBWP2550 4/14 2,18 PCBS5040 6/25 0,76 PCIS0500 4/20 0,88
PBPT6738 5/34 4,34 PBWP3020 2/29 1,31 PCCM0200 2/18 1,00 PCIS0900 6/32 1,49
PBPX1631 5/33 1,32 PBWP3030 2/29 1,79 PCCM0200 3/39 1,00 PCKI0250 4/20 0,25

System pro E power
List of codes
PCKI0800 5/36 2,82 PCVS0304 6/49 0,49 PDCB1820 6/45 5,00 PDLB2040 2/34 18,00
PCNL0050 4/26 2,23 PCVS0358 6/49 0,84 PDCB1844 2/36 10,50 PDLB2060 4/37 26,50
PCNL0100 4/26 3,17 PCVS0404 6/49 0,65 PDCB1844 6/46 10,50 PDLB2066 2/34 25,00
PCPA0004 2/20 1,00 PCVS0406 6/49 0,80 PDCB2020 2/36 5,64 PDLB2066 4/36 25,00
PCPT6738 5/34 8,00 PCVS0408 6/49 0,97 PDCB2020 6/45 5,64 PDLB2075 4/20 31,00
PCRM0188 5/30 0,44 PCVS0504 6/49 0,80 PDCB2030 2/36 9,00 PDLB2076 4/19 31,50
PCRM0438 5/30 1,04 PCVS1204 6/49 1,12 PDFC0200 4/8 - PDLB2500 2/35 38,00
PCRM0588 5/30 1,40 PCVS1254 6/49 1,06 PDFC0700 4/8 - PDLG1810 2/33 32,00
PCRM0638 5/30 1,55 PCVS1256 6/49 1,42 PDFC0900 4/8 - PDLG1810 4/19 32,00
PCRM0688 5/30 1,63 PCVS1258 6/49 1,68 PDGT4738 5/34 1,60 PDLG1810 4/36 32,00
PCRM0738 5/30 1,75 PCVS1304 6/49 1,32 PDGT5738 5/34 3,80 PDLG1816 2/33 32,00
PCRM0788 5/30 1,88 PCVS1306 6/49 1,57 PDGX1738 5/34 3,60 PDLG1816 4/18 32,00
PCRM1788 5/30 - PCVS1358 6/49 2,11 PDLB1810 2/34 34,00 PDLG1844 2/33 27,50
PCRM1988 5/30 - PCVS1404 6/49 1,64 PDLB1810 4/20 34,00 PDLG1846 2/33 18,00
9 PCRM2013 5/30 5,00 PCVS1406 6/49 1,94 PDLB1810 4/37 34,00 PDLG1850 4/19 20,00
PCRS0338 5/31 0,97 PCVS1408 6/49 2,29 PDLB1816 2/34 34,50 PDLG1856 4/18 20,00
PCSS0024 2/40 0,15 PCVS2256 6/50 1,80 PDLB1860 2/34 24,00 PDLG1882 2/33 32,00
PCTG1810 4/8 3,82 PCVS2258 6/50 2,11 PDLB1860 4/37 24,00 PDLG1886 2/33 27,50
PCTT6631 5/33 11,00 PCVS2504 6/50 2,41 PDLB2010 4/20 38,00 PDLG2046 2/33 20,00
PCVS0204 6/49 0,32 PCVS2604 6/50 2,85 PDLB2016 4/19 38,50 PDLG2060 2/33 25,00
PCVS0258 6/49 6,61 PDCB1820 2/36 5,00 PDLB2036 2/34 15,50 PDLG2066 4/18 25,00

PDLG2066 4/35 25,00 PFCB2025 5/36 0,89 PFCF8050 4/32 5,00 PFPF2040 3/20 7,70
PDLG2070 4/19 28,50 PFCB4080 5/36 0,34 PFCF8070 2/28 7,50 PFPF2060 3/20 7,80
PDLG2076 4/18 28,50 PFCC0023 5/36 0,84 PFCF8070 4/32 7,50 PFPF2080 3/20 8,68
PDLG2080 2/33 30,00 PFCF1030 2/28 3,80 PFCF8090 2/28 10,00 PFPS1840 3/20 15,00
PDLG2080 4/36 30,00 PFCF1030 4/15 3,80 PFCF8090 4/32 10,00 PFPS1860 3/20 17,00
PDLG2082 2/33 35,00 PFCF1050 2/28 6,92 PFCS1050 2/28 4,74 PFPS1880 3/20 18,00
PDLG2440 2/33 30,00 PFCF1070 4/15 9,37 PFCS1070 4/15 6,83 PFPT6738 5/34 11,80
PDLG2500 2/35 35,00 PFCF1070 4/32 9,37 PFCS1070 4/33 6,83 PFRF1840 3/42 5,40
PDLG2620 2/33 30,00 PFCF1090 2/28 12,60 PFCS1090 2/28 9,37 PFRF2040 3/42 5,92
PDLG2640 2/33 36,00 PFCF1090 4/15 12,60 PFCS1090 4/15 9,37 PFTT6631 5/33 12,20
PDLG2820 2/33 35,00 PFCF1090 4/32 12,60 PFCS1090 4/33 9,37 PFTT7631 5/33 26,80
PDLG8420 2/33 23,00 PFCF2031 2/23 - PFCS4050 2/28 1,67 PFTT7631 5/33 26,80
PDLG8440 2/33 27,50 PFCF2051 2/23 1,20 PFCS4070 2/28 2,40 PFVS1030 6/46 -
PDLG8500 2/35 32,00 PFCF2071 2/23 - PFCS4090 2/28 3,14 PFVS1032 6/46 -
PDLG8620 2/33 27,00 PFCF2091 2/23 - PFCS5050 4/15 3,60 PFVS1040 6/46 -
PDLG8640 2/33 31,50 PFCF2520 4/15 0,47 PFCS5070 4/15 3,40 PFVS1042 6/46 -
PDLG8820 2/33 32,00 PFCF2530 4/15 0,78 PFCS5090 4/15 - PFVS2012 6/30 2,71
PDPT4631 5/33 2,53 PFCF2550 4/15 1,41 PFCS6050 2/28 2,71 PFVS2040 6/28 1,22
PDPX1631 5/33 1,60 PFCF3050 2/28 1,50 PFCS6090 2/28 5,09 PFVS2062 6/23 1,54
PDPX2738 5/34 1,41 PFCF3090 2/28 3,00 PFCS7550 4/15 3,60 PFVS2082 6/23 2,63 9
PDPX4631 5/33 1,60 PFCF4031 2/23 - PFCS8050 2/28 3,64 PFVS2130 6/29 1,07
PDRP0300 3/39 - PFCF4051 2/23 - PFCS8070 2/28 6,01 PFVS2140 6/29 1,32
PDRP0500 3/39 - PFCF4070 2/28 3,50 PFCS8070 4/33 6,01 PFVS2220 6/29 0,46
PDRP0700 3/39 - PFCF4071 2/23 - PFCS8090 2/28 7,28 PFVS2222 6/31 0,94
PDRP0900 3/39 - PFCF4090 2/28 5,00 PFCS8090 4/33 7,28 PFVS2223 6/31 0,71
PDRS0400 3/22 1,13 PFCF4091 2/23 - PFFA1810 3/20 13,00 PFVS2240 6/29 1,02
PDRS0400 3/42 1,13 PFCF5020 4/15 1,00 PFFA1825 3/20 13,00 PFVS2242 6/31 1,36
PDTT4631 5/33 2,94 PFCF5090 4/15 5,93 PFFA1880 3/20 11,80 PFVS3042 6/30 1,61
PDTX1631 5/33 2,00 PFCF6070 2/28 5,50 PFFA2080 3/20 13,00 PFVS3132 6/30 1,26
PDTX2631 5/33 1,80 PFCF6070 4/32 5,50 PFNL1810 4/26 7,40 PFVS3222 6/31 0,70
PEBL0004 2/39 0,67 PFCF6090 4/15 7,50 PFNL2010 4/26 8,20 PFVS3243 6/31 1,74
PFBS1020 6/45 3,80 PFCF6090 4/32 7,50 PFNL2060 4/26 7,00 PFVS8030 6/46 -
PFBS1021 6/45 - PFCF7520 4/15 1,60 PFNL2080 4/26 7,40 PFVS8032 6/46 -
PFBS1040 6/45 - PFCF7530 4/15 1,67 PFPF1810 3/20 8,00 PFVS8040 6/46 -
PFBS1041 6/45 - PFCF7550 4/15 4,96 PFPF1812 3/20 9,24 PFVS8042 6/46 -
PFBS8020 6/45 - PFCF7570 4/15 7,13 PFPF1840 3/20 7,03 PGPP0040 2/32 0,19
PFBS8021 6/45 4,60 PFCF7590 4/15 9,00 PFPF1860 3/20 7,47 PGPP0040 4/18 0,19
PFBS8040 6/45 7,60 PFCF8020 2/28 1,50 PFPF1880 3/20 8,04 PGPP0040 4/35 0,19
PFBS8041 6/45 - PFCF8030 2/28 3,00 PFPF2010 3/20 9,23 PHBT4301 3/26 1,93
PFCB1016 5/36 0,66 PFCF8050 2/28 5,00 PFPF2012 3/20 9,80 PHBT4402 3/26 5,62

System pro E power
List of codes
PHBT4404 3/26 3,63 PHBX3405 3/25 3,20 PHCT5414 3/29 6,10 PHCX2404 3/27 4,26
PHBT5306 3/26 3,11 PHBX3423 3/25 3,75 PHCT5427 3/28 - PHCX2412 3/27 5,33
PHBX1101 3/24 3,19 PHBX4424 3/26 6,28 PHCT6411 3/29 12,44 PHCX3422 3/28 7,61
PHBX1407 3/24 3,30 PHCE1240 3/31 10,60 PHCT7329 3/29 5,42 PHCX4301 3/28 2,79
9 PHBX1409 3/24 3,51 PHCE1240 3/31 10,60 PHCT7329 3/29 5,42 PHCX4400 3/28 4,79
PHBX1423 3/24 3,30 PHCT4301 3/28 2,75 PHCT7420 3/29 5,99 PHCX4404 3/28 4,24
PHBX2400 3/25 3,61 PHCT5306 3/28 4,16 PHCX1101 3/27 4,32 PHCX4424 3/28 9,12
PHBX2402 3/25 4,97 PHCT5307 3/34 - PHCX1323 3/27 4,39 PHCX4425 3/28 8,97
PHBX2405 3/25 3,09 PHCT5310 3/34 - PHCX1404 3/27 4,31 PHCX4427 3/28 4,25
PHBX2409 3/25 3,46 PHCT5314 3/28 5,51 PHCX1407 3/27 4,28 PHDE1240 3/31 12,47
PHBX2424 3/25 6,35 PHCT5402 3/29 8,79 PHCX1423 3/27 4,28 PHDR0004 2/40 0,19
PHBX2424 3/25 6,35 PHCT5402 3/29 8,79 PHCX1424 3/27 9,25 PHDT4402 3/30 11,48
PHBX2431 3/25 5,68 PHCT5407 3/28 - PHCX2310 3/27 4,26 PHDT5309 3/30 6,92

PHDT5326 3/30 5,35 PKAT5050 4/13 - PKOH3180 3/37 7,17 PKPT8050 4/12 9,50
PHDT5406 3/30 6,27 PKAT7070 4/13 - PKOV1060 3/37 12,01 PKPT8090 2/25 11,00
PHDT5406 3/30 6,27 PKAT7070 4/31 - PKOV1080 3/37 13,89 PKPT8090 4/12 11,00
PHDT5409 3/30 8,15 PKAT9090 2/26 - PKOV1660 3/37 6,31 PKST0200 2/26 -
PHDT5414 3/30 7,91 PKDT0200 2/26 - PKOV3180 3/37 9,94 PKST0250 2/26 -
PHDT5423 3/30 6,21 PKDT0250 2/26 - PKPT1020 2/25 4,50 PKST0300 2/26 -
PHDT6401 3/30 7,70 PKDT0400 4/13 - PKPT1220 2/25 - PKST0500 4/13 -
PHDT6404 3/30 8,31 PKDT0400 4/31 - PKPT1220 4/12 - PKST0500 4/31 -
PHDX1301 3/30 - PKDT0500 2/26 - PKPT1259 2/25 17,00 PKST0501 2/26 -
PHDX1423 3/30 6,80 PKDT0500 4/31 - PKPT3020 2/25 2,00 PKST0501 4/31 -
PHDX2407 3/30 - PKDT0501 4/31 - PKPT3030 4/12 2,50 PKST0600 4/31 - 9
PHFP0020 3/45 0,80 PKDT0800 4/31 - PKPT4050 4/12 4,00 PKST0900 4/31 -
PHFR4180 2/40 0,77 PKDT0900 2/26 - PKPT4070 2/25 5,00 PKST1000 2/26 -
PHLL0020 2/38 0,25 PKDT0900 4/13 - PKPT4070 4/12 5,00 PKST1000 4/13 -
PHLS0010 2/38 0,24 PKDT0900 4/31 - PKPT4090 2/25 6,50 PKST1000 4/31 -
PIDH0010 2/38 0,30 PKDT1000 2/26 - PKPT4090 4/12 6,50 PKST1250 2/26 -
PIEH0008 2/38 0,02 PKDT1000 4/13 - PKPT6020 2/25 3,00 PKST1250 4/13 -
PIFH0020 2/38 0,02 PKDT1000 4/31 - PKPT6020 4/12 3,00 PKST1250 4/31 -
PIRH0405 2/38 0,20 PKDT1250 2/26 - PKPT6030 2/25 4,00 PLLS2050 6/31 -
PIRH2432 2/38 - PKEK0004 3/21 0,44 PKPT6050 4/12 5,50 PLLS3050 6/31 -
PIRP2040 3/42 0,94 PKMI0002 2/39 0,06 PKPT6070 2/25 7,50 PLLS3070 6/31 -
PISH0007 2/38 0,02 PKNL1210 4/26 13,60 PKPT6070 4/12 7,50 PLLS3090 6/31 -
PITE7120 5/34 0,50 PKNL1260 4/26 9,00 PKPT6090 2/25 9,00 PLSU0300 6/23 1,70
PITH0064 2/38 0,02 PKNL1280 4/26 10,40 PKPT6090 4/12 9,00 PLVS0552 6/41 -
PITH1234 5/34 0,23 PKOH1060 3/37 11,85 PKPT8020 2/25 4,00 PLVS0572 6/41 -
PITV6000 5/34 0,60 PKOH1680 3/37 6,31 PKPT8030 4/12 5,00 PLVS1072 6/41 -
PKAT5050 2/26 - PKOH3160 3/37 5,64 PKPT8050 2/25 9,50 PLVS1092 6/41 -

System pro E power
List of codes
PLVS1552 6/41 - PMCS2050 5/44 1,53 PPEA1830 4/18 6,50 PPEB1856 2/31 16,00
PLVS1752 6/43 0,58 PMCS2070 6/51 2,55 PPEA1850 4/18 10,00 PPEB1856 4/34 16,00
PLVS3052 6/35 1,00 PMRP2040 3/42 0,86 PPEA2050 4/35 11,00 PPEB1896 4/17 26,50
PLVS3052 6/43 1,00 PPAM0100 2/19 3,70 PPEA2060 2/31 12,00 PPEB1896 4/34 26,50
9 PLVS3092 6/35 2,48 PPAM0200 2/19 7,35 PPEA2070 4/18 14,00 PPEB2010 4/33 20,00
PLVS3552 6/43 1,18 PPBR2040 3/41 1,11 PPEA2080 2/31 15,00 PPEB2016 4/33 32,00
PLVS3572 6/43 1,95 PPBR2068 3/41 - PPEA2090 2/32 16,50 PPEB2020 4/17 6,00
PLVS3592 6/43 2,78 PPBR2088 3/41 - PPEA2090 4/35 16,50 PPEB2026 2/31 9,50
PLVS4052 6/35 1,35 PPBR4040 3/41 1,95 PPEB1810 2/30 18,00 PPEB2026 4/17 9,50
PLVS6052 6/35 2,10 PPBS0050 6/32 0,09 PPEB1820 2/32 5,50 PPEB2036 2/31 11,60
PLVS7072 6/27 4,12 PPCV1800 2/35 1,88 PPEB1830 2/30 7,00 PPEB2050 4/17 11,50
PMCS1755 5/44 1,36 PPDS0200 6/23 0,74 PPEB1840 2/30 8,50 PPEB2060 2/30 13,00
PMCS1755 6/51 1,36 PPDS0300 6/23 - PPEB1846 2/30 14,00 PPEB2060 4/33 13,00
PMCS1757 5/44 2,10 PPEA1810 2/31 15,50 PPEB1850 2/32 10,00 PPEB2066 2/30 20,20

PPEB2070 4/34 15,00 PPFB4540 3/40 - PPFM1080 4/28 3,07 PPMD3060 3/23 -
PPEB2075 4/16 25,00 PPFB4560 3/40 - PPFM1090 2/21 3,42 PPMD3080 3/23 -
PPEB2076 2/31 23,50 PPFB4580 3/40 3,77 PPFM1090 4/9 3,42 PPMF1540 3/23 0,63
PPEB2080 2/30 16,50 PPFB5008 3/40 4,23 PPFV1800 2/35 4,50 PPMF2060 3/23 1,20
PPEB2090 4/17 18,00 PPFB6040 3/40 2,51 PPFV2000 4/37 4,42 PPMU3060 3/23 1,89
PPEB2090 4/34 18,00 PPFB6060 3/40 3,63 PPIM0100 2/20 3,09 PPMU3060 5/38 1,89
PPEB2096 2/31 28,00 PPFB6080 3/40 5,00 PPIM0200 2/20 6,45 PPMU3080 3/23 2,43
PPEB2096 4/17 28,00 PPFB8010 3/40 8,93 PPLA1820 2/31 10,50 PPMU3080 5/38 2,43
PPEB2096 4/34 28,00 PPFB8040 3/40 3,31 PPLA1820 4/17 10,50 PPNL3010 4/26 3,40
PPFA1010 3/41 1,16 PPFB8060 3/40 4,98 PPLA2020 2/31 12,00 PPNL3060 4/26 2,14
PPFA1040 3/41 0,46 PPFB8080 3/40 6,37 PPLA2020 4/17 12,00 PPNL3080 4/26 3,00
PPFA1060 3/41 0,69 PPFH0250 4/20 1,20 PPLB1820 2/30 11,50 PPNL4010 4/26 4,60
PPFA2040 3/41 0,87 PPFH0500 4/20 1,68 PPLB2020 4/16 13,00 PPRA1820 2/31 14,00
PPFA2060 3/41 1,22 PPFH0600 2/35 1,99 PPMB1510 3/38 2,99 PPRA1820 4/17 14,00
PPFA2080 3/41 1,61 PPFH0600 4/37 1,99 PPMB1540 3/38 0,63 PPRA2020 2/31 16,00
PPFB1010 3/40 1,24 PPFH0750 4/20 2,19 PPMB1560 3/38 1,81 PPRA2020 4/17 16,00
PPFB1040 3/40 0,50 PPFH0800 2/35 2,40 PPMB1580 3/38 2,26 PPRB1820 2/30 15,50
PPFB1510 3/40 1,89 PPFH1000 4/20 2,78 PPMB2040 3/38 2,56 PPRB2020 4/16 17,00 9
PPFB1540 3/40 0,76 PPFH1000 4/37 2,78 PPMB2060 3/38 3,06 PPRR6040 3/42 -
PPFB1560 3/40 1,06 PPFH1250 2/35 3,32 PPMB2080 3/38 3,83 PPRS0150 6/23 0,09
PPFB1580 3/40 1,41 PPFH1250 4/20 3,32 PPMB2512 3/38 6,00 PPRS0200 6/23 0,05
PPFB1840 3/40 7,00 PPFI2726 3/41 1,34 PPMB2540 3/38 2,77 PPRS0200 6/28 0,05
PPFB2012 3/40 2,87 PPFM1010 2/21 3,69 PPMB3080 3/38 4,68 PPRS0400 6/23 0,13
PPFB3010 3/40 3,51 PPFM1030 4/9 1,32 PPMB4080 3/38 5,56 PPVS2200 6/22 0,36
PPFB3540 3/40 - PPFM1060 2/21 2,38 PPMB5006 3/38 5,35 PPVS2500 6/22 0,87
PPFB4010 3/40 4,48 PPFM1070 4/9 2,70 PPMB6040 3/38 4,56 PRBE1243 3/42 5,81
PPFB4080 3/40 3,50 PPFM1080 2/21 3,07 PPMD3040 3/23 - PRBS1220 6/47 2,62

System pro E power
List of codes
PRBS1240 6/47 5,09 PRVS2125 6/42 3,57 PRVS7010 6/45 9,11 PSHS8090 6/36 8,96
PRBS8220 6/47 2,10 PRVS2210 6/42 3,23 PRVS7040 6/45 3,93 PSHW1096 6/37 2,09
PRBS8240 6/47 4,00 PRVS2240 6/42 1,29 PRVS7041 6/34 1,37 PSHW1296 6/37 2,59
PRVS0141 6/40 - PRVS2241 6/38 1,30 PRVS7041 6/44 1,37 PSHW4051 3/42 0,46
PRVS1010 6/45 13,25 PRVS2562 6/39 0,98 PRVS8081 6/44 3,47 PSHW6094 6/37 1,45
PRVS1040 6/45 5,35 PRVS2580 6/42 2,78 PRVS8082 6/44 4,16 PSHW8051 6/37 0,87
PRVS1040 6/47 5,35 PRVS2580 6/42 2,78 PSAF0016 2/40 0,66 PSHW8071 6/37 1,47
PRVS1041 6/44 3,20 PRVS2581 6/38 1,06 PSBS0065 2/39 0,39 PSHW8072 6/37 1,20
PRVS1060 6/45 8,04 PRVS2581 6/38 1,06 PSCP0024 2/40 0,28 PSHW8074 6/37 1,20
PRVS1061 6/44 2,05 PRVS2582 6/39 1,33 PSCS0579 2/39 0,52 PSHW8091 6/37 2,20
PRVS1062 6/44 4,21 PRVS2582 6/39 1,33 PSHF1096 6/37 2,60 PSHW8092 6/37 1,76
9 PRVS1062 6/47 4,21 PRVS3010 6/42 4,15 PSHF1296 6/37 3,14 PSHW8094 6/37 1,77
PRVS1080 6/45 10,33 PRVS3041 6/34 0,57 PSHF4072 3/42 0,82 PSRM1515 3/43 0,13
PRVS1081 6/44 5,25 PRVS3041 6/38 0,57 PSHF4072 6/37 0,82 PSVF6042 3/42 -
PRVS1082 6/44 5,23 PRVS3041 6/38 0,57 PSHF4092 3/42 1,11 PSVF6042 6/24 -
PRVS1541 6/40 - PRVS3060 6/42 2,40 PSHF4092 6/37 1,11 PSVF6062 6/24 8,11
PRVS1582 6/40 - PRVS3080 6/42 3,20 PSHF8072 6/37 1,51 PSVS0055 6/32 4,00
PRVS1582 6/40 - PRVS3080 6/42 3,20 PSHF8092 6/37 2,16 PSVS0057 6/32 5,91
PRVS1710 6/42 2,51 PRVS3081 6/34 1,29 PSHF8092 6/37 2,16 PSVS0105 6/34 0,73
PRVS1740 6/42 1,03 PRVS3081 6/38 1,29 PSHS1400 6/50 0,37 PSVS0107 6/34 1,07
PRVS1782 6/39 0,97 PRVS3541 6/34 0,68 PSHS1912 6/22 - PSVS0209 6/34 2,55
PRVS2082 6/39 1,10 PRVS6081 6/34 2,57 PSHS8070 6/36 7,00 PSVS2051 6/33 -

PSVS2070 6/32 1,74 PTBB1030 2/24 6,00 PTBB3096 2/22 5,54 PTBB8050 2/24 7,40
PSVS2071 6/33 - PTBB1030 4/11 6,00 PTBB4020 2/24 2,10 PTBB8050 4/29 7,40
PSVS3050 6/32 1,81 PTBB1070 4/11 12,00 PTBB5026 4/30 2,56 PTBO1030 2/27 4,08
PSVS3051 6/33 - PTBB1070 4/29 12,00 PTBB5050 2/23 5,05 PTBO1030 4/14 4,08
PSVS3590 6/32 3,86 PTBB1096 4/30 14,85 PTBB6026 2/22 3,03 PTBO1231 2/23 -
PSVS3593 6/33 - PTBB1220 4/11 5,50 PTBB6036 2/22 3,95 PTBO1251 2/23 -
PSVS4050 6/32 2,33 PTBB1230 4/11 5,80 PTBB6050 2/24 5,80 PTBO1270 4/14 8,60 9
PSVW5061 6/24 6,38 PTBB2576 4/10 4,08 PTBB7526 4/30 3,56 PTBO3030 2/27 2,06
PTBB1020 2/24 4,50 PTBB3056 4/10 3,46 PTBB7596 4/30 12,04 PTBO5070 4/14 4,29

System pro E power
List of codes
PTBO6050 4/32 3,95 PTHS3030 6/29 1,46 PTVS8072 6/27 4,06 PVBX2405 3/32 4,10
PTBO6070 2/27 4,25 PTHS3050 6/29 2,28 PTVS8091 6/27 5,71 PVBX2407 3/32 4,08
PTBO6070 4/32 4,25 PTHS3052 6/30 1,36 PUCM1800 2/17 3,00 PVBX2409 3/32 4,42
PTBO6090 2/27 5,01 PTHS3070 6/29 3,34 PUCM2000 2/17 3,50 PVBX2410 3/32 4,10
PTBO6090 4/32 5,01 PTHS3072 6/30 2,27 PUCS1800 2/17 2,83 PVBX2412 3/32 4,51
PTBO7520 4/14 3,14 PTHS3090 6/29 4,24 PUCS2000 2/17 3,20 PVBX2417 3/32 4,35
PTBO7530 4/14 3,57 PTHS3092 6/30 3,28 PUKI1800 3/21 2,87 PVBX2423 3/32 4,57
PTBO8231 2/23 - PTHS4190 6/29 5,12 PUPM1800 2/15 15,38 PVBX4405 3/32 4,16
PTBO8251 2/23 5,60 PTHS4192 6/30 4,08 PUPM1800 4/8 15,38 PVBX4407 3/32 6,13
PTBS1001 6/27 2,65 PTHS4252 6/31 1,42 PUPM2000 2/15 16,50 PVBX4412 3/32 4,50
PTBS1052 6/27 3,43 PTHS4292 6/31 3,35 PVBE1241 3/36 4,79 PVCE1240 3/36 6,82
PTBS1052 6/44 3,43 PTHS6030 6/28 2,42 PVBE1241 3/36 4,79 PVCE1240 3/36 6,82
9 PTBS1052 6/47 3,43 PTHS6050 6/28 3,99 PVBT4404 3/32 5,01 PVCE1241 3/36 6,92
PTBS1070 6/26 8,92 PTHS6052 6/30 2,41 PVBT4406 3/32 4,55 PVCE1241 3/36 6,92
PTBS1072 6/47 5,75 PTHS6092 6/30 5,65 PVBT5319 3/33 - PVCE2442 3/36 7,16
PTBS1090 6/26 - PTHS8030 6/28 3,16 PVBT5404 3/33 4,91 PVCE2450 3/36 6,88
PTBS8050 6/26 5,05 PTHS8072 6/30 5,11 PVBT5414 3/33 4,47 PVCT4404 3/34 6,77
PTBS8052 6/27 2,30 PTHS8092 6/30 7,15 PVBT5414 3/33 4,47 PVCT4406 3/34 6,25
PTBS8052 6/44 2,30 PTRN1951 5/35 0,35 PVBT5423 3/33 5,40 PVCT4406 3/34 6,25
PTBS8052 6/47 2,30 PTRS1201 5/35 1,35 PVBT5426 3/33 4,44 PVCT4423 3/34 7,46
PTBS8070 6/26 6,93 PTRS1601 5/35 1,55 PVBT5426 3/33 4,44 PVCT5307 3/34 -
PTBS8072 6/27 4,56 PTRS2001 5/35 1,74 PVBT5428 3/33 5,25 PVCT5404 3/34 6,71
PTBS8072 6/44 4,56 PTVB1091 6/27 8,31 PVBT6312 3/33 6,69 PVCT5406 3/34 6,24
PTBS8072 6/47 4,56 PTVB1091 6/44 8,31 PVBT6314 3/33 5,01 PVCT5406 3/34 6,24
PTBS8090 6/26 - PTVB1091 6/47 8,31 PVBT6314 3/33 5,01 PVCT5412 3/34 7,82
PTBS8091 6/27 6,64 PTVS1001 6/27 2,06 PVBT6401 3/33 5,21 PVCT5414 3/34 6,07
PTHS1052 6/30 3,84 PTVS1050 6/26 5,37 PVBX1401 3/32 4,13 PVCT5426 3/34 6,20
PTHS1292 6/30 10,57 PTVS1072 6/27 7,89 PVBX1405 3/32 4,13 PVCT5601 3/34 -
PTHS2030 6/29 0,85 PTVS1091 6/27 7,26 PVBX1407 3/32 4,18 PVCT5710 3/34 -

PVCT7413 3/34 6,88 PVDE2440 3/36 9,15 PVGE6230 3/36 26,86 TS4013 5/43
PVCT7413 3/34 6,88 PVDE2440 3/36 9,15 PVGE6231 3/36 30,60 VB7012 2/40
PVCT7413 3/34 6,88 PVDE2440 3/36 9,15 PVGE6231 3/36 30,60 VB7035 2/40
PVCT7413 3/34 6,88 PVDE2440 3/36 9,15 PWRP1640 3/39 16,20 ZN1041 2/20
PVCT7419 3/34 7,44 PVDE2441 3/36 10,81 PWRP1660 3/39 22,60
PVCT7419 3/34 7,44 PVDE2441 3/36 10,81 PWRP1680 3/39 30,60
PVCT7419 3/34 7,44 PVDE2441 3/36 10,81 PWRP1840 3/39 20,20
PVCT7419 3/34 7,44 PVDE2441 3/36 10,81 PWRP1860 3/39 26,40
PVCX1301 3/33 - PVDT5404 3/35 8,51 PWRP1880 3/39 34,50
PVCX1401 3/33 5,67 PVDT5406 3/35 8,11 PWRP2040 3/39 21,00
PVCX1404 3/33 5,65 PVDT5406 3/35 8,11 PWRP2060 3/39 30,00
PVCX1405 3/33 5,70 PVDT5412 3/35 9,98 PWRP2080 3/39 37,20
PVCX1407 3/33 5,69 PVDT5414 3/35 7,84 TS4011 5/43 2,00
PVCX1409 3/33 6,08 PVDT5414 3/35 7,84 TS4012 5/43 2,00
PVCX1423 3/33 5,78 PVDT5423 3/35 9,79 TS4013 5/43 2,00
PVCX1427 3/33 5,62 PVDT5426 3/35 7,98 VB7012 2/40 0,52
PVCX1707 3/33 5,76 PVDT5426 3/35 7,98 VB7035 2/40 0,60
PVCX2400 3/33 5,56 PVDT5428 3/35 9,56 ZN1041 2/20 1,50
PVCX2401 3/33 5,65 PVDT5610 3/35 7,53 PVDT7419 3/35
PVCX2404 3/33 4,89 PVDT5612 3/35 9,58 PVDT7419 3/35
PVCX2405 3/33 5,67 PVDT5701 3/35 - PVDT7419 3/35
PVCX2407 3/33 5,56 PVDT5810 3/35 - PVDT7419 3/35
PVCX2409 3/33 6,76 PVDT6401 3/35 8,83 PVDX1807 3/35
PVCX2410 3/33 5,64 PVDT6404 3/35 9,32 PVDX2801 3/35
PVCX2412 3/33 6,09 PVDT6405 3/35 5,57 PVDX2807 3/35
PVCX2417 3/33 6,22 PVDT6412 3/35 11,78 PVDX3707 3/35
PVCX2423 3/33 6,25 PVDT6414 3/35 9,64 PVDX3807 3/35
PVCX2427 3/33 5,63 PVDT6414 3/35 9,64 PVDX4701 3/35
PVCX2701 3/33 5,65 PVDT7413 3/35 7,88 PVDX4707 3/35 9
PVCX2707 3/33 6,21 PVDT7413 3/35 7,88 PVDX4801 3/35
PVCX3301 3/33 - PVDT7413 3/35 7,88 PVDX4807 3/35
PVCX3401 3/33 5,51 PVDT7413 3/35 7,88 PVFE1263 3/36
PVCX3404 3/33 5,59 PVDT7419 3/35 8,90 PVFE6230 3/36
PVCX3405 3/33 5,61 PVDT7419 3/35 8,90 PVFE6230 3/36
PVCX3407 3/33 5,58 PVDT7419 3/35 8,90 PVFE6231 3/36
PVCX3409 3/34 5,95 PVDT7419 3/35 8,90 PVFE6231 3/36
PVCX3423 3/34 7,00 PVDX1807 3/35 6,69 PVFT5710 3/35
PVCX3427 3/34 5,56 PVDX2801 3/35 6,96 PVFT5712 3/35
PVCX3607 3/33 5,65 PVDX2807 3/35 6,52 PVFT5810 3/35
PVCX3707 3/33 5,43 PVDX3707 3/35 7,04 PVFT5812 3/35
PVCX4400 3/34 6,27 PVDX3807 3/35 6,50 PVFT6610 3/35
PVCX4401 3/34 5,55 PVDX4701 3/35 6,87 PVFT6610 3/35
PVCX4404 3/34 5,54 PVDX4707 3/35 7,16 PVFT6612 3/35
PVCX4405 3/34 5,61 PVDX4801 3/35 6,85 PVFT7633 3/35
PVCX4407 3/34 6,12 PVDX4807 3/35 7,17 PVFT7633 3/35
PVCX4409 3/34 6,67 PVFE1263 3/36 10,61 PVGE6230 3/36
PVCX4410 3/34 6,24 PVFE6230 3/36 24,06 PVGE6230 3/36
PVCX4412 3/34 6,77 PVFE6230 3/36 24,06 PVGE6231 3/36
PVCX4417 3/34 6,60 PVFE6231 3/36 25,63 PVGE6231 3/36
PVCX4423 3/34 6,86 PVFE6231 3/36 25,63 PWRP1640 3/39
PVCX4427 3/34 6,12 PVFT5710 3/35 9,10 PWRP1660 3/39
PVCX4601 3/34 5,66 PVFT5712 3/35 11,40 PWRP1680 3/39
PVCX4607 3/34 5,90 PVFT5810 3/35 8,89 PWRP1840 3/39
PVCX4701 3/34 5,53 PVFT5812 3/35 11,28 PWRP1860 3/39
PVCX4707 3/34 5,70 PVFT6610 3/35 11,48 PWRP1880 3/39
PVDE1240 3/36 9,15 PVFT6610 3/35 11,48 PWRP2040 3/39
PVDE1240 3/36 9,15 PVFT6612 3/35 13,92 PWRP2060 3/39
PVDE1241 3/36 8,97 PVFT7633 3/35 10,88 PWRP2080 3/39
PVDE1241 3/36 8,97 PVFT7633 3/35 10,88 TS4011 5/43
PVDE1262 3/36 8,14 PVGE6230 3/36 26,86 TS4012 5/43

Note
Note
System pro E power New main distribution switchboards up to 6300A
Contacts
ABB SACE The data and illustrations are not binding. We reserve
1STC803005D0204 - 10 .2015
the right to change the contents of this document with-
A division of ABB S.p.A. out prior notice, in the course of technical development
Automation and Distribution Boards of the product.
Via Italia, 58 Copyright 2015 ABB. All rights reserved.
23846 Garbagnate Monastero (LC) - Italy

Tel: +39 031 3570.111
Fax: +39 031 3570.228
www.abb.com/lowvoltage
System pro E power

New main distribution switchboards up to

6300A

Power en October 2015

Uploaded by

Copyright:

Available Formats

Power en October 2015

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Power en October 2015

Uploaded by

Copyright:

Available Formats

System pro E power New main distribution switchboards up to 6300A

Via Italia, 58 Copyright 2015 ABB. All rights reserved.

23846 Garbagnate Monastero (LC) - Italy

Technical catalogue | October 2015

System pro E power

Technical catalogue | October 2015

ABB Technical catalogue | 1STC803005D0204

ABB SACE, a division of ABB S.p.A., has always been at the

ABB: Energy efficiency for sustainable

Technical software Calculation and cost estimate tools www.abb.it/lowvoltage

Among the enterprises belonging to the Group, ABB SACE is in

ABB: quality of the certified product

Composition of the series 1/6

ABB Technical catalogue | 1STC803005D0204 1/1

The switchboards comprise the following components:

1/2 1STC803005D0204 | ABB Technical catalogue

ABB Technical catalogue | 1STC803005D0204 1/3

1/4 1STC803005D0204 | ABB Technical catalogue

ABB Technical catalogue | 1STC803005D0204 1/5

STRUCTURE EXTERNAL COVERS

1/6 1STC803005D0204 | ABB Technical catalogue

KITS FOR APPARATUS MAIN DISTRIBUTION SYSTEM

ABB Technical catalogue | 1STC803005D0204 1/7

General information 2/2

Choice of the structure

Guide to the order codes 2/14

ABB Technical catalogue | 1STC803005D0204 2/1

Uprights and crosspieces

Functional dimensions available Structures with blind door

2/2 1STC803005D0204 | ABB Technical catalogue

Door and Panels

ABB Technical catalogue | 1STC803005D0204 2/3

2/4 1STC803005D0204 | ABB Technical catalogue

Structural crosspieces for depth and width

Uprights in galvanized sheet metal

Universal angle pieces for plinths in

Plinth flanges in galvanized sheet metal

ABB Technical catalogue | 1STC803005D0204 2/5

Doors and panels

The handle can

2/6 1STC803005D0204 | ABB Technical catalogue

Glass door or blind door in pickled steel

External rear panel in pickled steel sheet

External side panel in pickled steel sheet

Incoming cable flanges in pickled steel

ABB Technical catalogue | 1STC803005D0204 2/7

H=1800mm quick selection guide

700 816 PCFM0700 PPFM1070 PTBB6076 PTBB6070 PTBO6070 PBWP6070

200 316 PCFM0200 PPFM1020 PTBB1220

900 1016 PCFM0900 PPFM1090 PTBB1290 PTBO1290 PBWP1290

2/8 1STC803005D0204 | ABB Technical catalogue

Glass door Blind door

PPEB1856 PPEB1850 PPEA1850 PCCM0500

PPEB1856 PPEB1850 PPEA1850 PCCM0500

PPEB1856 PPEB1850 PPEA1850 PCCM0500

PPEB1876 PPEB1870 PPEA1870 PCCM0700

PPEB1856 PPEB1850 PPEA1850 PCCM0500

PPEB1856 PPEB1850 PPEA1850 PCCM0500

PPEB1890 PPEA1890 PCCM0900

ABB Technical catalogue | 1STC803005D0204 2/9