Fosroc Conplast SP470 constructive solutions

Superior high range water reducer specifically designed Description

for superplasticised high performance concrete
Conplast SP470 is chloride free, superplasticising admixture
Uses based on selected synthetic and organic polymers.
 Specifically formulated for use in high performance as
Conplast SP470 disperses the fine particles in the concrete
well as normal concrete.
mix, enabling the water content of the concrete to perform
 Recommended for low slump concrete to produce more more effectively. The very high levels of water reduction
uniform, predictable and consistent concrete. possible allow major increases in strength to be obtained.
 To provide early and ultimate strength gain by Special slump retainers help to retain workability also.
significantly reducing water content in a concrete mix
 To provide improved durability by increasing ultimate Typical Properties
strengths and reducing concrete permeability. Appearance : Brown liquid
 To significantly improve the workability and retention of Specific gravity : 1.23 @ 25° C
site mixed concrete without increasing water demand Chloride content : Nil to BS 5075 / BS:EN934
 Specifically developed for use in high quality concrete
mixes utilising cement replacements. Instructions for use
Mix design
 Ideally suited for factory-line concrete production
including applications using cement replacement Where the main requirement is to retain workability over
materials and white cement. considerable period of time and to improve strengths, initial
 Can be used for effective dispersion in coloured trials should be made with normal concrete mix designs.
concrete.
The addition of the admixture will allow the removal of water
 Can be used in semi-dry conditions from the mix whilst maintaining workability. After initial trials,
minor modifications to the overall mix design may be made
Advantages to optimise performance.
 High range water reducing property helps achieve high
early-strengths and low water absorption values. Compatibility
 High early strengths help in reducing production cycles Conplast SP470 is compatible with other Fosroc admixtures
 Reduced permeability levels even for low slump concrete used in the same concrete mix. All admixtures should be
especially in the case of the precast elements, which added to the concrete separately and must not be mixed
reduces penetration of water and other deleterious together prior to addition. The resultant properties of con-
impurities and increases the durability of concrete. Also crete containing more than one admixture should be as-
reduces efflorescence. sessed by trial mixes.
 Improves cohesion and particle/pigment dispersion to Conplast SP470 is suitable for use with all types of Portland
produce dense concrete matrix. cements and cement replacement materials such as PFA,
 Chloride free, suitable for use in precast, prestressed and GGBFS, metakaolin and microsilica.
reinforced concrete.
The use of a combination of admixtures in the same concrete
 Compatible with all portland cements including cement mix and or cement replacements may alter the setting time.
replacement materials and white cement. Trials should always be conducted to determine such setting
 Helps in superior concrete finishes which increase life of times.
moulds.
 Can help in moderate slump retention. Dispensing

The correct quantity of either Conplast SP470 should be

Standards compliance
measured by means of a recommended dispenser.

Conplast SP470 conforms with BS 5075, BS:EN 934-2 and Normally, the admixture should then be added to the con-
with ASTM C494 as Type G depending on dosage used. crete with the mixing water to obtain the best results. These
Conplast SP470

admixtures are not recommended to be added in dry aggre-

gates or cement. It should always be added in wet mix
conditions. Full blending of the admixture and the concrete
Fosroc Conplast SP470

should be ensured by mixing at high speed for a period of at Estimating

least two minutes. Contact Fosroc for advice regarding
Supply
suitable equipment and its installation.
Conplast SP470
210 litre drum, 1000 litre totes or bulk
Dosage Guideline
For larger users, storage tanks can be supplied.
The optimum dosage of Conplast SP470 to meet specific
requirements should always be determined by trial mixes Storage
using the materials and conditions that will be experienced in
Conplast SP470 should be re-circulated two-three times a day
use. Normal concrete dosage range is between 0.2 to 2% by
for 20 - 30 minutes and has a minimum shelf life of 12 months
weight of cement or cementitious materials. Dosage can be
provided the temperature is kept within the range of 2°C to 50°C.
used up to 2.5% by weight of cement for high performance
Should the temperature of the product fall outside this range
concrete. Contact Fosroc Technical department for further
contact Fosroc for advice.
advice.
Freezing point: Approximately -2°C
Use at other dosages
Health and safety
Dosages outside the above dosage guidelines can be used
to meet particular concrete mix requirements. Please contact Conplast SP470 does not fall into the hazard classifications of
Fosroc for advice in such cases. current regulations (see notes 1 and 2 below). However, it
should not be swallowed or allowed to come into contact with
Effects of overdosing skin and eyes.

An overdose of double the amount of Conplast SP470 will Suitable protective gloves and goggles should be worn. Splash-
result in a slight increase in slump retention and retardation. es on the skin should be removed with water. In case of contact
Provided that adequate curing is maintained, the ultimate with eyes, rinse immediately with plenty of water and seek
strength of the concrete will not be impaired by increased medical advice. If swallowed seek medical attention immediately
retardation and will generally be increased. The effects of - do not induce vomiting. For further information consult the
overdosing will be further increased if sulphate resisting Material Safety Data Sheet available for this product.
cement or cement replacement materials is used. Overdos-
age may also cause increased air entrainment, which will Fire
tend to reduce strength. The degree of this effect will depend
Conplast SP470 is water based and nonflammable.
on the particular mix design and overdose level.

Cleaning and disposal

Spillages of Conplast SP470 should be absorbed onto sand,

earth or vermiculite and transferred to

suitable containers. Remnants should be hosed down with

large quantities of water. The disposal of excess or waste
material should be carried out in accordance with local
* Denotes the trademark of Fosroc International Limited
legislation under the guidance of the local waste regulatory
authority.

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected]
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected]
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: [email protected]
Oman, Al Amana telephone: 24815080 fax: 24817554 email: [email protected]
www.fosroc.com

UAE/0586/15/D