Structuro W435

Fosroc® Structuro® W435 constructive solutions
Hyperplasticizer - Mid-Range hyperplasticizer based on Technical support

polycarboxylate technology
Fosroc provides a technical advisory service for on-site assis-
tance and advice on admixture selection, evaluation trials and
Uses
dispensing equipment. Technical data and guidance can be
Structuro W435 is a high performance hyperplasticiser intend- provided for admixtures and other products for use with fresh
ed for applications where increased ultimate compressive and hardened concrete.
strengths is required, and it has been developed for use in:
 Highrise pumped concrete Dosage Guideline
 High strength/grade e.g.(M60/M70/M80) The optimum dosage of Structuro W435 to meet specific re-
 Flow or Self compacting concrete along with Auramix quirements should always be determined by trial mixes using
V200 if required, based on mix design. the materials and conditions that will be experienced in use.
Guideline dosage range is between 0.2 to 2.2% by weight of
 Concrete requiring long workability retention
cement or cementitious materials including PFA, GGBFS &
 High performance mass concrete
microsilica.
Use at other dosages

Advantages
 Improved adhesion to reinforcing and stressing steel Dosages outside the above dosage guidelines can be used to
meet particular concrete mix requirements. Please contact
 Improved resistance to carbonation
Fosroc for advice in such cases.
 Lower permeability
Effects of overdosing
 Increased resistance to aggressive atmospheric
conditions An overdose of Structuro W435 will result in an increase in
retardation and air content as compared to that normally ob-
 Reduced shrinkage and creep
tained. Provided that adequate curing is maintained, the ulti-
 Increased workability retention without affecting setting
mate strength of the concrete will not be impaired by increased
time
retardation and will generally be increased. The effects of
 Enhanced pumpability overdosing will be further increased if sulphate resisting cement
or cement replacement materials are used.
Standards compliance
Typical Properties
Structuro W435 conforms with BS 5075, BS:EN 934-2 and
with ASTM C494 as Type F & G depending on the dosage Appearance : Light Yellowish
used. Specific gravity : 1.07 ± 0.02@ 25°C
Chloride content : Nil to BS 5075 / BS:EN934
Description
Structuro W435 is differentiated from conventional superplas- Instructions for use

ticisers in that it is based on a unique carboxylic ether polymer Mix design
with long lateral chains. This greatly improves cement disper-
sion. At the start of the mixing process an electrocstatic dis- Where the main requirement is to improve strengths, initial
persion occurs but the presence of the lateral chains, linked trials should be made with normal concrete mix designs. The
to the polymer backbone, generate a steric hindrance which addition of the admixture will allow the removal of water from
stabilises the cement particle’s capacity to separate and dis- the mix whilst maintaining workability. After initial trials, minor
perse. This mechanism considerably reduces the water de- modifications to the overall mix design may be made to opti-
mand in flowable concrete. mise performance.
Structuro W435 combines the properties of water reduction Where the main requirement is to provide high workability
and workability retention. It allows the production of high per- concrete, the mix design should be one suitable for use as a
Structuro W435
formance concrete and/or concrete with high workability. pump mix. Advice on mix design for flowing concrete is avail-
able from Fosroc.
Structuro W435 is a particularly strong hyperplasticiser allow-
ing production of consistent concrete properties around the
required dosage.
Fosroc® Structuro® W435
Compatibility Storage
Structuro W 435 is suitable for use with all types of concrete Structuro W435 has a minimum shelf life of 6 months provided
mixes produced with Portland Cements (OPC) and mixes the temperature is kept within the range of 5°C to 50°C. Should
with cement replacement materials such as PFA, GGBFS, the temperature of the product fall outside this range then
SRC cements or microsilica. contact Fosroc for advice.
Structuro W 435 should not be used in combination with any Precautions

other admixture unless prior approval is obtained from your Health and safety
local Fosroc office.
Structuro W435 does not fall into the hazard classifications of
All admixtures should be added to the concrete separately current regulations. However, it should not be swallowed or
and must not be premixed together prior to addition. The allowed to come into contact with skin and eyes.
use of a combination of admixtures in the same concrete mix Suitable protective gloves and goggles should be worn.
may alter the setting time. The resultant properties of
Splashes on the skin should be removed with water. In case
concrete containing more than one admixture should be
of contact with eyes rinse immediately with plenty of water and
assessed by lab/or plant trial mixes to confirm the desired
seek medical advice. If swallowed seek medical attention im-
properties of concrete before use.
mediately - do not induce vomiting.
Dispensing For further information consult the Material Safety Data Sheet
available for this product.
The correct quantity of Structuro W 435 as per the approved
mix designs based on lab/plant trials should be measured by
means of a recommended dispenser or load cells. Normally, Fire
the admixture should then be added to the concrete with the
Structuro W435 is water based and non-flammable.
mixing water to obtain the best results. These admixtures are
not recommended to be added in dry aggregates or cement. Cleaning and disposal
It should always be added in wet mix conditions.
Spillages of Structuro W435 should be absorbed onto sand,
earth or vermiculite and transferred to suitable containers.
Full blending of the admixture and the concrete should be
Remnants should be hosed down with large quantities of water.
ensured by mixing at high speed.
The disposal of excess or waste material should be carried out
Packaging in accordance with local legislation under the guidance of the
local waste regulatory authority.
Structuro W435
Bulk and 1000 Liter Plastic Totes
® Denotes the trademark of Fosroc International Limited
For larger users, storage tanks can be supplied.
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected]
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected]
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: [email protected]
Oman, Al Amana telephone: 24815080 fax: 24817554 email: [email protected]
www.fosroc.com
UAE/0654/18/D

Structuro W435

Uploaded by

Copyright:

Available Formats

Structuro W435

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Structuro W435

Uploaded by

Copyright:

Available Formats

Fosroc® Structuro® W435 constructive solutions

Hyperplasticizer - Mid-Range hyperplasticizer based on Technical support

Use at other dosages

Structuro W435 is differentiated from conventional superplas- Instructions for use

Structuro W 435 should not be used in combination with any Precautions

You might also like