0% found this document useful (0 votes)
29 views44 pages

VSX Intro Program

The document discusses technical specifications, keypad functions, group parameters, VFD parameterization, protection parameters, Modbus communication, and answers several application questions regarding running and stopping a VFD using push buttons, virtual I/O terminal configuration, auto/manual operations, C2 group parameter configuration, using digital and analog comparators.

Uploaded by

eami.contacto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
29 views44 pages

VSX Intro Program

The document discusses technical specifications, keypad functions, group parameters, VFD parameterization, protection parameters, Modbus communication, and answers several application questions regarding running and stopping a VFD using push buttons, virtual I/O terminal configuration, auto/manual operations, C2 group parameter configuration, using digital and analog comparators.

Uploaded by

eami.contacto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 44

CG Drives and Automation

Emotron VS Series VFD


1 Technical Specfication

2 Group Parameter

CONTENTS
3 VFD Parameterization

4 Applications

5 Dedicated Applications
Technical Specification
Technical Specification
Technical Specification
Keypad Function
Keypad Indication
Group Parameters
VFD Parameterization

Continue..
Parameter Upload/Download
Page Monitor
Oscilloscope
Parameters

1) Factory Reset Manual Page -49

2) Motor Ctrl Mode Selection

Manual Page -50


Parameters
3) Frequency Command source selection

Manual Page -51


Parameters

4) Run Stop Ctrl Manual Page -52

5) Acc./Dec Time setting Manual Page -53


Parameters

6) Digital Input Configuration


Manual Page -53,54
Parameters

7) Digital Output Configuration

Manual Page -55


Parameters

8) Analog Input (V/I) selection

Note: If the analog I/P as 4-20mA

a) Change the jumper to I position


b) C2.00-18.5
c) C2.01-100%
Manual Page -57
Parameters

9) Analog Output Config.

Manual Page -59


Protection Parameters (E0-Grp)
To resolve Err01 make E0.00-0

Manual Page -67

Change the setting according to error


to resolve Err07, Err09, Err10, Err11,
Err12.

Manual Page -68


Protection Parameters (E0-Grp)

Change the setting according to error to resolve Err13, Err15, Err18, Err19, Err20

Manual Page -68


Protection Parameters (E0-Grp)

Change the setting according to error to resolve Err24 & Err25.

Manual Page -69


Modbus Communication (H0-Grp)

Modbus Communication parameters –(RS485)

Manual Page -79

• Half Duplex- (2 wire)


Application FAQ
Q.1 How to run & stop the VFD through Push button? ( Once the user press the run PB it will run until
emergency or stop PB is being applied). Also configure the VFD, so that it will reach 40Hz in 4sec & stop
within 3sec from maximum frequency 50Hz.

Sol:
Parameters:

B1.00-- 01
C0.00-- 01
C0.01-- 03
C0.15-- 02
B2.00-- 05
B2.01-- 03

3 wire control
Application FAQ
Q.2 How to Configuration of virtual I/O terminal?
Sol:
For example: DI1 for run, DI2 is for Multi-speed, master
frequency command source is keypad potentiometer,
auxiliary frequency command source is Multi-reference.
Parameters setting:
b0.01=1 (-) (+) PB
AC R U
b0.03=4 Input S
T
V
W
M
b1.00=1
c0.00=1 +24V

PLC
c0.01=20
Run DI1
c4.01=13 Multi-speed DI2 Drive
c4.08=23 DI3
DI4
c4.13=10 DI5
R1A
R1B
f1.00=Multi-speed 0 DI6
R1C
DI7/HI
f1.01=Multi-speed 1 COM
Application FAQ
Q.3 How to configure Auto/Manual operations?

Sol:

B0.00 2 Switch between master and Aux cmd.

B0.01 2 AI1
B0.03 8 AI2
B1.00 1 Terminal ctrl
C0.00 01 Run forward (FWD)
C0.01 20 Frequency cmd. Pattern shift
Application FAQ
Q.4 Washing machine auto/manual operations?

Application Description: If the system is in auto mode then after run cmd. the motor will run forward
for 5 sec (include hold) at 5hz, then it will stop and hold for 5 sec and again will run in reverse direction
and same pattern will follow until the user stops the operation. In Manual mode once the user run for
first time the motor will run in forward direction and then stops and if gives the run command again
then it will run in reverse direction and stops as per set time.
Sol:
B0.01 0
B0.02 Manual Frequency
B0.03 5
B1.00 1
B2.00 Acc. time
B2.01 Dec. time
C0.00 1 (Fwd.)
C0.01 2 (Rev.)
C0.02 41 (Reserved)

Continue..
Application FAQ
Q.4 Washing machine auto/manual operations?
C0.03 20
Solution:
C0.13 00100
C0.15 2
C4.00 41
C4.03 42
C4.04 3
C4.05 10000
C4.06 10000
C4.07 33
F1.00 +10.0% (set as per reqd.)
F1.01 0.0%
F1.02 -10.0% (set as per reqd.)
F1.03 0.0%
F1.17 10012
F1.18 10.0 (set as per reqd.)
F1.19 5.0 (set as per reqd.)
F1.20 10.0 (set as per reqd.)
F1.21 5.0 (set as per reqd.)
F3.08 1
F3.09 1
F3.10 10 (Set as per reqd.)
Application FAQ
Q.5 How to Configuration of C2 group parameters?

Sol:

Pls refer the right figure.


The C2.00,C2.02,C2.04,C2.06 is input value.
For example:
0-10v signal,0v is match 0%,10v is match 100%;
4-20mA signal,4mA is match 20%(4/20*100%),20mA is
match 100%.

The C2.01,C2.03,C2.05,C2.07 is match value.


For example:
0-10v signal,0v is match 0hz,10v is match 50hz;
4-20mA signal,4mA is match 0hz,20mA is match 50hz.
Application FAQ
Q.6 How to use digital comparator?

Sol:
Comparator input source selection of digital
comparator 1,consistent with C1.00 parameters, please
refer the right figure shows.
For example:use R1 output the DI1 function.
Parameters setting:
C1.02=29 Valid
F3.00=22
Input

Valid

Output
T
Application FAQ
Q.7 How to use analog comparator?
Sol: Analog Input
Logic:When analog comparator source selection input signal is bigger
than analog comparator higher value, related terminal outputs ON 80% Higher value
signal, when analog comparator source selection input signal is lower
than analog comparator lower value, related terminal outputs OFF
signal, please refer to right figure.
20% Lower value
For example:use R1 output the analog comparator 1 function,when
running hz up to 50hz,output valid,when running hz below 30hz,output
T
invalid.
Output
Parameters setting: Valid

C1.02=31
F3.02=7
F3.03=100% T

F3.04=60%
Application FAQ
Q.8 How to use timer delay mode?
Trigger
Sol: signal
Logic:In delay mode, when trigger source signal of timer is
valid, timer starts and when the timer’s time is not greater
than timer’s delay time, related terminal outputs OFF signal.
When the timer’s time is lesser than timer’s delay time, T
Output
related terminal output is ON signal, please refer the figure.
For example: use R1 output the timer1 function, when drive
running, need wait 20s output the run signal.
Parameters setting:
T
C1.02=33 Delay time
F3.09=1
F3.10=20
Application FAQ
Q.9 How to use timer high and lower electrical level alternating mode?
Sol:
Trigger
Logic: In high and low electrical level alternating mode, signal
when trigger source signal of timer is valid, and when timer
outputs alternating high and low electrical level, related
terminal outputs ON and OFF signal as per high electrical
and lower electrical level time set by function code. T
Output
For example: use R1 output the timer1 function, when drive
running, need output run signal 5s,and stop output run
signal 5s,keep cycle .
Parameters setting: T
C1.02=33 High electrical level Low electrical level
time time
F3.09=2
F3.11=5
F3.12=5
Gearless PMSM– Elevator
Silent features

❑ Single drive for either IM or PM motor control

❑ Support close Loop

❑ Support PG Card ECN1313, Sin Cos(ERN1387)

❑ Various types of auto-tuning for induction and gearless


permanent magnet motors (uncoupled/coupled)
Dedicated
01
Application – Multipump
Multi-pumps constant pressure water supply specially
developed for constant pressure water supply industry,
featured with 3 modes below:

• Mode 1: Fixed variable frequency control mode


– One Drive with Mulitpump
• Mode 2: Two variable frequency control mode.
(Alternate Master)- Two Pump with two drive
• Mode 3: Multi variable frequency pumps cycle
control mode (Alternate Master) with optional
relay board
Wiring
01
– Multi Variable Mode
EmoWizard
01
EmoWizard
01
PROFIBUS Module Introduction
01

Power on Led
PEOFIBUS OK Led
PROFIBUS ERROR Led
MODBUS OK Led
MODBUS ERROR Led

RS485 plug
DP plug
Power
PROFIBUS Module Introduction
01
PROFIBUS Module Introduction
01

1.Install GSD file:FRK_DP_V1 2.Build a Project 3.Add “FRK_DP_V1” module to


DP system

6. Set parameters start address for


4. Add the type you want to read/write 5.Set PLC Data Input and Output read/write. (Modbus address , decimal)
Address
VFD Application >50+ Application Support
01
1. Wire drawing Application. 21. HVLS Fan 41. High suction PMSM Blower
2. VSX Negative logic 22. Feeder Application 42. PMSM Compressor
3. Elevator Application. 23. Granular machine 43. Canal paving machine
4. Auto trolley Textile 24. Rota Evaporator 44. Long travel
5. Washing machine. 25. Tissue paper machine 45. AHU
6. Hydro Mixer 26. Bottle cap fitting and liquid filling machine 46. Hoist
7. Bread making Machine 27. Vertical Lathe Machine 47. Mixer
8. Air Compressor 28. Ceiling fan motor winding machine 48. Circular Loom machine
9. Fibrizer 29. Sugar Cane Feeder Table 49. Auto Trolley Textile
10. Solar Pump 30. Sugar Cane Carrier 50. Tensile tester
11. Master slave 31. Sugar Cane Machine 51 Tension control Winder
12. Conveyor 32. Hot Forging Press 52. Skip Bucket Application
13. Elevator Door. 33. Micronizer 53. JIB Crane Application
14. STP Supply Pump 34. ID BLOWER Application 54. VSI Stone Crusher
15. Plastic sheet winder (Dancer control) 35. 3 Axis CNC MACHINE 55. Wire Travelling Machine
16. Extruder. 36. Pipe Welding Lathe Machine 56. Bagasse Feeder
17. Cheese winder 37. Cement Pipe Molding machine 57. Mechanical Circulator
18. Incense stick 38. Tread Mill 58. Multi-Pumps Constant Pressure water Supply
19. Crane hoist 39. Bin washing machine 59. PMSM Load Test Kit
20. Spindle 40. Cement Pipe Coating Machine

more….
Links
01

QR Code Online Portal

https://itapp.cgglobal.com/Econnect/
THANK YOU !

www.emotron.com

You might also like