Iso 6603 1 2000
Iso 6603 1 2000
Iso 6603 1 2000
STANDARD 6603-1
Second edition
2000-03-01
(standards.iteh.ai)
Partie 1: Essais de choc non instrumentés
ISO 6603-1:2000
https://standards.iteh.ai/catalog/standards/sist/a61b5475-0597-481b-a7f1-
c8596647d289/iso-6603-1-2000
Reference number
ISO 6603-1:2000(E)
© ISO 2000
ISO 6603-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 · CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
Contents Page
Foreword.....................................................................................................................................................................iv
1 Scope ..............................................................................................................................................................1
2 Normative references ....................................................................................................................................2
3 Terms and definitions ...................................................................................................................................3
4 Principle..........................................................................................................................................................5
5 Apparatus .......................................................................................................................................................6
6 Test specimens ..............................................................................................................................................9
7 Procedure .....................................................................................................................................................10
8 Precision.......................................................................................................................................................16
9 Test report ....................................................................................................................................................16
Annex A (informative) Examples of calculations ...................................................................................................19
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 6603 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 6603-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 2, Mechanical properties.
(standards.iteh.ai)
ISO 6603 consists of the following parts,
behaviour of rigid plastics:
under the general title Plastics — Determination of puncture impact
ISO 6603-1:2000
Part 1: Non-instrumented impact testing
https://standards.iteh.ai/catalog/standards/sist/a61b5475-0597-481b-a7f1-
c8596647d289/iso-6603-1-2000
Part 2: Instrumented impact testing
Part 1:
Non-instrumented impact testing
1 Scope
This International Standard specifies methods for the determination of puncture-impact properties of rigid plastics in
the form of flat test specimens, such as discs or square pieces, under defined conditions. Specimens may be
moulded directly, cut from sheets or taken from finished products. Different types of test specimens and test
conditions are defined.
These falling-dart methods are used to investigate the behaviour of plastic sheeting or mouldings under the impact
of a striker applied perpendicular to the plane of the specimen.
iTeh STANDARD PREVIEW
This part of ISO 6603 can be used if it is sufficient to characterize the impact behaviour of plastics by a threshold
(standards.iteh.ai)
value of impact-failure energy based on many test specimens. ISO 6603-2 is used if a force-deflection or force-time
diagram, recorded at nominally constant striker velocity, is necessary for detailed characterization of the impact
behaviour. ISO 6603-1:2000
https://standards.iteh.ai/catalog/standards/sist/a61b5475-0597-481b-a7f1-
These test methods are applicable to specimens with a thickness between 1 mm and 4 mm.
c8596647d289/iso-6603-1-2000
NOTE For thicknesses less than 1 mm, ISO 7765 should preferably be used. Thicknesses greater than 4 mm may be
tested if the equipment is suitable, but the test falls outside the scope of ISO 6603-1 and ISO 6603-2.
These methods are suitable for use with the following types of material:
rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and
sheets;
rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and
laminates;
These methods are also applicable to specimens which are either moulded or machined from finished products,
laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and
surfaces as well as the test conditions are the same. In particular, results determined on specimens of different
thickness cannot be compared with one another (see annex E of ISO 6603-2:—). Comprehensive evaluation of the
reaction to impact stress requires that determinations be made as a function of impact velocity and temperature for
different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken
from finished products (see above) for test by these methods.
Test data developed by these methods should not be used for design calculations. However, information on the
typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see
annex D of ISO 6603-2:—), by varying the thickness (see annex E of ISO 6603-2:—) and by testing specimens
prepared under different conditions.
Two statistical methods of test are described in this part of ISO 6603:
In this method, a uniform energy increment is employed during testing. The energy is decreased or increased
by the uniform increment after testing each specimen, depending upon the observed result (pass or fail) for the
preceding test.
In this method, successive groups of at least ten test specimens are tested. The impact failure energy is
calculated by statistics.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 6603. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 6603 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
iTeh STANDARD PREVIEW
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
(standards.iteh.ai)
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing.
ISO 6603-1:2000
https://standards.iteh.ai/catalog/standards/sist/a61b5475-0597-481b-a7f1-
ISO 293:1986, Plastics — Compression moulding test specimens of thermoplastic materials.
c8596647d289/iso-6603-1-2000
ISO 294-3:1996, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates.
ISO 1268:19741), Plastics — Preparation of glass fibre reinforced, resin bonded, low-pressure laminated plates or
panels for test purposes.
ISO 6603-2:—2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented
impact testing.
ISO 7765-1:1988, Plastics film and sheeting — Determination of impact resistance by the free-falling dart
method — Part 1: Staircase methods.
ISO 7765-2:1994, Plastics film and sheeting — Determination of impact resistance by the free-falling dart
method — Part 2: Instrumented puncture test.
1) Under revision.
3.1 General
3.1.1
failure
any break in the surface of the specimen which is visible to the naked eye
3.2.1
crack
any fissure that can be observed by the naked eye and that does not penetrate the full thickness of the material
(see Figure 1)
3.2.2
break
any fissure through the full thickness of the material (see Figure 2)
3.2.3
penetration
failure in which the striker penetrates through the whole thickness of the test specimen [see Figure 3 b)]
3.2.4
iTeh STANDARD PREVIEW
shattering (standards.iteh.ai)
breaking of the test specimen into two or more pieces [see Figure 3 a)]
ISO 6603-1:2000
3.3 Impact-failure terms
https://standards.iteh.ai/catalog/standards/sist/a61b5475-0597-481b-a7f1-
c8596647d289/iso-6603-1-2000
3.3.1
50 % impact-failure energy
E50
the energy that will cause 50 % of the test specimens to fail as defined in 3.1.1
3.3.2
50 % impact-failure mass
M50
the mass that will cause 50 % of the test specimens to fail, as defined in 3.1.1, for a given height of fall
3.3.3
50 % impact-failure height
H50
the height that will cause 50 % of the test specimens to fail, as defined in 3.1.1, using a given falling mass
Key
1 Impact direction
Figure 2 — Sections through specimens damaged by a “break” b) and c) after bending by hand
4 Principle
The impact strength of suitably sized test specimens is determined by striking them with a lubricated weighted
striker dropped vertically from a known height. The test specimen is impacted at its centre by a striker,
perpendicular to the surface of the specimen.
Two methods of adjusting the energy at impact are permitted: altering the mass at constant height and altering the
height at constant mass.
NOTE The variable-height procedure is velocity-dependent, and differing results may be observed depending upon the
material’s strain rate.
5 Apparatus
weights,
¾ a specimen support (see Figure 4), optionally with a clamping device (Figure 5).
The test device shall permit the test specimen to be punctured at its centre, perpendicular to the specimen surface.
Key
1 Test specimen 6 Stand for falling-dart system
2 Hemispherical striker tip 7 Holding and release system for weighted striker
3 Test specimen support 8 Guide shaft for weighted striker
4 Clamping ring (optional) 9 Weighted striker
5 Base 10 Acoustic isolation (optional)
Key
1 Clamping ring (optional)
2 Specimen support
Dimensions in millimetres
Specimen type
iTeh STANDARD
Square of side 60PREVIEW
Disc of diam. 140
D 40 ± 2
(standards.iteh.ai)
2 100 ± 5
D3 60 140
D4 ISO 6603-1:2000
min. 90 min. 200
https://standards.iteh.ai/catalog/standards/sist/a61b5475-0597-481b-a7f1-
H 12
c8596647d289/iso-6603-1-2000 12
R 1 1
The falling-dart system shall be capable of holding and releasing a weighted striker such that it will fall constrained
by one or more guides. The fall shall be nominally without friction and losses through windage, or the amount of
friction has to be taken into account in the calculations.
Appropriate weights are required that can be firmly attached to the striker. The combined mass of the attached
weights, and the mass of the striker, shall be known to within 1 %.
5.1.4 Striker
The preferred striker has a polished hemispherical striking surface with a diameter 20 mm 0,2 mm. Alternatively,
a 10 mm 0,1 mm diameter striking surface may be used.
NOTE The size, dimensions and condition of the surface of the striker will affect the results.
The preferred striker is one made of any material with sufficient resistance to wear and of sufficiently high strength
to prevent plastic deformation. In practice, hardened tool steel or similar material with a hardness of 54 HRC has
been found acceptable. Harder materials or materials with a lower density (for example titanium) with equivalent