Mifare® Application

Programming Guide
for DESFire®

REV.E
August 10, 2011

1
DESFire® Schema (In Command Mode)

Field On

Activate WakeUP / Idle

RATS Deselect

Select other Application

Select Application

Continue with other key

Authenticate

Continue

Set Key Settings Get File List Read Data (All) Write Data (Backup)

Get Key Settings Get File Settings Write Data (Std)

Credit
Change Key Change File Settings Get Value Debit
Get Key Version Create Data File
Read Records Limited Credit
Create Value File
Create App (Master)
Create Record File Write Records
Delete Application
Delete File Clear Records
Get AID List

Get Card Version

Commit Transaction
Format PICC (Master)
Abort Transaction

2
MFAP Extend Functions Table for DESFire® (40h~5Fh)
Query (Master/Host) Response (Slave/Device)
Commands
Func Len Parameters Len Data Bytes
T=CL Commands
0 4/7 CSN (4 bytes)
Activate WakeUp / Idle 40h
1 Flag (byte) UID (7 bytes)
RATS 0
41h 6 ATS
(Request to Answer To Select) 1 CID (byte, 0~14)
ACK, Successful
DESELECT 42 0 1
NAK, TCL Error Code
Security related commands
ACK, Successful
17 Key#(byte) + Key(16 bytes) 2
NAK, Error Code
Key#(byte) + Crypto Type(byte) ACK, Successful
18 2
Authenticate + Key(16 bytes) NAK, Error Code
43h ACK, Successful
2 Key#(byte) + Crypto Type(byte) 2
NAK, Error Code
Key#(byte) on Reader + Crypto
ACK, Successful
3 Type(byte) + Key#(byte) on 2
NAK, Error Code
Card
ACK, Successful
Set Key Settings 1 Settings (byte) 2
NAK, Error Code
44h
Key Settings
Get Key Settings 0 2
Number of Keys
Key# (byte),
17
New Key (16 bytes)
Change Key 45h Key#(byte),
33 New Key(16 bytes)
Old Key(16 bytes)
Key# (byte), ACK, Successful
1
18 Key Version(byte) NAK, Error Code
New Key (16 bytes)
Change Key for AES 45h Key#(byte),
Key Version(byte)
34
New Key(16 bytes)
Old Key(16 bytes)
ACK, Version
Get Key Version 46h 1 Key# (byte) 1
NAK, Error Code
17
Key#(Byte) ACK,
Save Key 6Bh or 0
+ Key Value(16 or 24 Bytes) NAK, Error Code
25
Card Level Commands
AID (long, MSB First)
ACK, Successful
Create Application 47h 6 Key Settings(byte) 1
NAK, Error Code
Number of Keys(byte) + Crypto

3
 Type(bit6~7)(byte)
ACK, Successful
Delete Application 48h 4 AID (long, MSB first) 1
NAK, Error Code
AID List
Get AID List 49h 0 n
(long, MSB first)
ACK, Successful
Select Application 4Ah 4 AID (long, MSB first) 1
NAK, Error Code
ACK, Successful
Format PICC 4Bh 0 1
NAK, Error Code
Get Card Version 4Ch 0 28 Version Info
Applications Level Commands
Get FID List 4Dh 0 n FID List
Get File Settings 1 FID (byte) n fileSettings
FID (byte),
4Eh ACK, Successful
Set File Settings 4 Communication Mode (byte), 1
NAK, Error Code
Access Right (int, MSB first)
FID(byte),
Create Std Data File 4Fh
Communication Mode(byte), ACK, Successful
8 1
Access Right(int, MSB first), NAK, Error Code
Create Back Data File 50h
File Size(long, MSB first)
FID(byte),
Communication Mode(byte),
Access Right(int, MSB first),
Lower Limit(long, MSB first), ACK, Successful
Create Value File 51h 17 1
Upper Limit(Long, MSB First), NAK, Error Code
Initial Value(Long, MSB
First),
Limited Credit Enabled(byte)
FID(byte),

Create Linear Record File 52h Communication Mode(byte),

Access Right(int, MSB first), ACK, Successful
12 1
Record Size(long, MSB first), NAK, Error Code

Create Cyclic Record File 53h Max. Num of Records(long, MSB

first)
Delete File 54h 1 FID(byte)
File Level Commands
FID(byte),
Read Data 55h
Offset(long, MSB first), Length(long, MSB first)
9 4/1
Length(long, MSB first) NAK, Error Code,
Write Data 56h
*Length=0~128
Value(long, MSB first)
Get Value 57h 1 FID(byte) 4/1
NAK, Error Code
Credit 58h
FID(byte), Amount(long, MSB first)
Debit 59h 5
Amount(long, MSB first) NAK, Error Code
Limited Credit 5Ah

4
 FID(byte),
Length(long, MSB first)
Write Record 5Bh 9 Offset(long, MSB first), 4/1
NAK, Error Code
Length(long, MSB first)
FID(byte),
Count (long, MSB first)
Read Records 5Ch 9 Record#(long, MSB first), 4/1
NAK, Error Code
NRecToRead (long, MSB first)
ACK, Successful
Clear Record 5Dh 1 FID(byte) 1
NAK, Error Code
Commit Transaction 5Eh ACK, Successful
0 1
Abort Transaction 5Fh NAK, Error Code
Additional
Get File Buffer Addr. 60h 0 2 ACK, File Buffer Addr
ACK, 7 Bytes UID
Get UID 62h 0 4/2
NAK, Error Code
ACK, Free Memory (LONG)
Get Free Memory 64h 0 4/2
NAK, Error Code

LED & Buzzer Commands

(00h)All LED Off, Buzzer Off
(01h)Green LED ON
(02h)Green LED OFF
(03h)Red LED ON
(04h)Red LED OFF
Control LED & Buzzer 3Ch 1 1 ACK, Successful
(05h)Buzzer Beep 1 Time
(06h)Buzzer Beep 3 Time
(07h)Green LED ON with Beep 1
(08h)Red LED ON with Beep 3
(09h)All LED ON (Orange)
GNetPlus Base Commands
Polling 00h 0 n Return OEM Status
Get Version 01h 0 n Return OEM Version String
Set Slave Addr 02h 1 New Address (1~255) 0
Get Register 09h 3 Reg.Address2 + Reg.Lenght n Reg.Block
Set Register 0Ah n Reg.Address + Reg.Buffer 0

5
Symbols and abbreviated terms
ACK positive ACKnowledgement
AID Application IDentifier
ATQ Answer To reQuest
ATS Answer To Select
CID Card IDentifier
CRC Cyclic Redundancy Check
CSN Card Serial Number
DES Data Encryption Standard
3DES DES 3 times
FID File IDentifier
GNet Giga-tms Network protocol
GNetPlus Giga-tms Network protocol Plus version
HLTA HALT command, Type A
Int 16 bit (2 bytes) signed integer
Key# Key Number (KeyNo)
Long 32 bit (4 bytes) signed integer
MAD Mifare Application Directory
NAK Negative AcKnowledgment
PCD Proximity Coupling Device (Reader)
PICC Proximity Card
RATS Request for Answer To Select
REQA REQuest command, type A
RFU Reserved for Future Use
SAK Select AcKnowledge
UID Unique IDentification
WUPA Wake-UP command, type A

6
Activate Wake-Up / Activate Idle (40H)

Func Len Parameters

0 (WUPA)
40h
1 flag (byte, 0x00=Activate Idle, 0x80=Activate Wakeup)

Following command set according to ISO14443-3:

Activate Wakeup (len=0) for PICC in Idle, Deselect or Halt state only.
Activate Idel (len=1, flag=0x80) for PICC in Idle state only.

Response:
ACK, UID (7 bytes) or CSN (4 bytes)

Example (Activate Wakeup):

:004000 PCD send the Activate WakeUp Command
:000607044A5601366E10 PICC response the UID

Examples (Activate Idle):

:00400100 PCD send the Activate Idle command
:000607044A5601366E10 PICC response the UID

7
RATS (41H)

Func Len Parameters

0
41h
1 CID (byte, 0~14)

Following command set according to ISO14443-4:

The response to the RATS command communicates the PICC capabilities to the PCD

CID : The logical number is in the range from 000 to 0x0E. This CID is used to distinguish several PICCs
simultaneously selected by a single PCD. Default CID=0 when len=0.

Response:
ACK, ATS (6 Bytes)

Examples:
:004000 PCD send Activate WakeUp command:000607041917795A1B80
PICC response the UID
:004100 PCD send RATS (Default CID=0)
:000606067577810280 PICC response the ATS (6 bytes)

8
DESELECT (42h)

Func Len Parameters

42h 0

Following command set according to ISO14443-4:

To free the selected card after RATS.

Examples:
:004000 PCD send Activate WakeUp command:000607041917795A1B80
PICC response the UID
:004100 PCD send RATS (Default CID=0)
:000606067577810280 PICC response the ATS (6 bytes)
:004200 PCD send DESELECT command:0006020000
PICC response ACK

Remark:
You have to use the Activate Wake-Up command to request the card after DESELECT.

9
Authenticate (43h)

Func Len Parameters

43h 17 Key# + Key (16 bytes)
43h 18 Key# + Crypto Type + Key (16 bytes for AES)
43h 26 Key# + Crypto Type + Key (24 Bytes for 3K3DES)
43h 2 EEPROM/Card Key# + Crypto Type
43h 3 EEPROM Key# + Crypto Type + Card Key#

Crypto Type:
0x00 – DES/3DES
0x40 – 3K3DES
0x80 – AES

In this procedure both, the PICC as well as the reader device, show in an encrypted way that they possesthe
same secret which especially means the same key. This procedure not only confirms that both entitiescn trust
each other but also generates a session key which can be used to keep the further communication successfully
completed a new key for further cryptographic operations is obtained.

Depending on the configuration of the application (represented by its AID), an authentication has to be done to
perform specific operations:
 Gather information about the application
 Change the keys of the application
 Create and delete files within the application
 Change access right
 Access data files in the authenticated application

Depending on the security configuration of the PICC, the following commands may require an authentication
with the PICC (AID=0) master keys:
 Gather information about the application on the PICC
 Change the PICC master key itself
 Change the PICC key settings
 Create a new application
 Delete an existing application
 Format PICC

The authentication state is invalidated by

 Select an application
 Changing the key which was used for reaching the currently valid authentication status
 A failed authentication

Remark:
Master keys are identified by their key number 0x00. This is valid on PICC level (AID = 0x00) and on
Application level (AID ≠ 0x00).

10
Set / Get Key Settings (44h)

Func Len Parameters

1 (Set) Settings (byte)
44h
0 (Get)

This command set or get (len=0) the master key configuration settings depending on the currently selected AID.
If AID=0x00 has been selected in advance, the change applies to the PICC key settings, otherwise (AID≠0x00)
it applies to the application key settings of the currently selected application.

PICC (AID=0) Master Key Settings:

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

PICC master key not

access without PICC

required for create /

Allow changing the

Free directory list

PICC master key

Configuration
Changeable

master key
delete
RFU

RFU

RFU

RFU

On PICC Level (selected AID=0x00) the coding is interpreted as:

Bit 3: codes whether a change of the PICC master key settings is allowed:
 0 = configuration no changeable anymore (frozen).
 1 = this configuration is changeable if authenticate with PICC master key (default).

Bit 2: codes whether PICC master key authentication is needed before Create/Delete application
 0 = Create/Delete application is permitted only with PICC master key authentication.
 1 = Create application is permitted without PICC master key authentication (default).
note
Delete application require an authentication with PICC master key or application master key .

Bit 1: codes whether PICC master key authentication is needed for application directory access:
 0 = Successful PICC master key authentication is required for executing the “Get AID List” and “Get
Key Settings” commands.
 1 = “Get AID List” and “Get Key Settings” command succeed independently of a preceding PICC
master key authentication (default).

Bit 0: codes whether the PICC master key is changeable:

 0 = PICC master key is not changeable anymore (frozen).
 1 = PICC master key is changeable (authentication with the current PICC master key necessary,
default).

Note:
In case of usage of the application master key for deletion, the application which is about to be deleted need to
be Selected and Authenticated with the application master key prior to the “Delete Application” command.

11
Application (AID≠0) Master Key Settings:
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Change Key Access

Change Key Access

Change Key Access

Change Key Access

Free create / delete

without master key

Free directory list

Allow changing
access without
Configuration
Changeable

master key

master key
Right Bit 3

Right Bit 2

Right Bit 1

Right Bit 0

On Application Level (selected AID≠0x00) the coding is interpreted as:

Bit 7-4: hold the Access Rights for changing application keys (Change Key command).
 0x0 = Application master key authentication is necessary to change any key (default).
 0x1…0xD = Authentication with the specified key is necessary to change any key.
 0xE = Authentication with the key to be changed (same Key#) is necessary to change a key.
 0xF = All keys (except application master key, see Bit 0) within this application are frozen.

Bit 3: codes whether a change of the application master key settings is allowed:
 0 = configuration not changeable anymore (frozen).
 1 = this configuration is changeable if authenticated with the application master key (default).

Bit 2: codes whether application master key authentication is needed before “Create File” / “Delete File”
 0 = “Create File” / “Delete File” is permitted only with application master key authentication.
 1 = “Create File” / “Delete File” is permitted also without application master key authentication (default).

Bit 1: codes whether application master key authentication is needed for file directory access:
 0 = Successful application master key authentication is required for executing the “Get FID List”, “Get
File Settings” and “Get Key Settings” commands.
 1 = “Get FID List”, “Get File Settings” and “Get Key Settings” commands succeed independently of a
preceding application master key authentication (default).

Bit 0: codes whether the application master key is changeable:

 0 = Application master key is not changeable anymore (frozen).
 1 = Application master key is changeable (authentication with the current application master key
necessary, default).

12
Change Key (45h)

Func Len Parameters

17 Key#(byte) + New Key (16 bytes)
33 Key#(byte) + New Key (16 bytes) + Old Key (16 bytes)
45h
18 Key#(byte) + Key Version(byte) + New Key (16 bytes)
34 Key#(byte) + Key Version(byte) + New Key (16 bytes) + Old Key (16 bytes)

This command allows to change any key stored on the PICC.

If AID=0x00 is selected, the change applies to the PICC master key and therefore only KeyNo = 0x00 is valid
(only one PICC master key is present on a PICC). In all other cases (AID ≠ 0x00) the change applies to the
specified KeyNo within the currently selected application (represented by it’s AID).

Remark:
 To Change any key (except Master Key and the “Change Key” Key), authentication with the “Change Key”
is necessary.
 To Change the “Change Key” Key or the Master Key, authentication with the Master Key is necessary.
 Len=17 or 18, in case the Key# used for authentication is the SAME as the Key# parameter to be changed
or if “Change Key Access Right” is set 0xE.
 Len=33 or 34, in case the Key# used for authentication is the DIFFERENT from the Key# parameter to be
changed or if “Change Key Access Right” is set to a value ≠ 0xE.
 Len=18 or 34, in case the Key version only for AES.

13
Get Key Version (46h)

Func Len Parameters

46h 1 Key#(byte)

The Get Key Version command allows to read out the current key version of any key stored on the PICC.

If AID = 0x00 is selected, the command return the version of the PICC master key and therefore only KeyNo =
0x00 is valid (only one PICC master key is present on a PICC). In all other cases (AID≠0x00) the version of
the specified KeyNo within the currently selected application (represented by it’s AID) is returned.

Remark:
If you use 3DES or single DES:

Even if the first 8 byte key itself is the same as the second 8 byte, but the key version is coded into one half, it is used as

3DES key and not as a single DES key during authentication and session key generation, see example as below:

Example for single DES keys

-------------------------------------------------------------------------------------------

key (hex) = 00 11 22 33 44 55 66 76 00 11 22 33 44 55 66 77

-------------------------------------------------------------------------------------------

version = 0 1 0 1 0 1 0 0 n/a n/a n/a n/a n/a n/a n/a n/a

-------------------------------------------------------------------------------------------

Key version is coded in first 8 byte for 3DES and single DES, so the version would be : 0x54

Apart from AES key, where the key version is stored in the key settings, the key version for a DES key is stored in the

so called parity bit. For single double or triple length keys, only 8 left bytes of the key stream are concerned for

the key version.

Save Key (6Bh)

Func Len Parameters

17 Key#(byte) + Key Value 16 Bytes (for AES)
6Bh
25 Key#(byte) + Key Value 24 Bytes (for 3K3DES)

The Save Key command allows to save key value to reader’s EEPROM and manage by Key#.
Remark:
Key# : 0~13

14
Create Application (47h)

Func Len Parameters

AID (long 4 bytes, MSB First)
47h 6 Key Settings (byte)
Number of Keys(bit0~3) + Crypto Type(bit6~7) (byte)

The “Create Application” command allows to create new applications on the PICC.

 This command requires that currently selected AID=0x00 which references the card level.
 The 32 bits AID the first parameter of the command. (Range 1 ~ 16777215 ).
 The second parameter is the Application Master Key Settings as defined in Page 11.
 The last parameter “Number of Key” defines how many keys can be stored within the application for
cryptographic purposes.
Bit7 Bit6 Crypto Type
0 0 DES/3DES
0 1 3K3DES
1 0 AES

Note:
All keys are initialized with a string consisting of sixteen 0x00 bytes and therefore.

15
Delete Application (48h)

Func Len Parameters

48h 4 AID (long 4 bytes, MSB First)

The “Delete Application” command allows to permanently deactivate applications on the PICC.
The application which will be deleted is represented by it’s AID, which is the only parameter of this command.

Either a preceding PICC master key authentication or an application master key authentication is required.

16
Get AID List (49h)

Func Len Parameters

49h 0

The “Get AID List” command return the Application IDentifiers of all active applications on a PICC.

Response:

Func Len Parameters

ACK first AID (long, MSB first) … N AID (long, MSB first)
len = (N) * 4

Example:
:004000 PCD send Activate WakeUp
command:00060704491B815A1B80 PICC response UID
:004100 PCD send RATS:000606067577810280
PICC response ATS
:004A0400000000 PCD select AID=0 (card level):00060100
PICC response ACK
:0043110000000000000000000000000000000000 PCD send Authentication command:0006020000
PICC response ACK
:004900 PCD send “Get AID List”
command:00061000000001000000020000000300000004 PICC response AID List (total 4 AIDs in list)

PICC’s AIDs List as below:

0x00000000 (master, default)
0x00000001 (4 bytes)
0x00000002
0x00000003
0x00000004

17
Select Application (4Ah)

Func Len Parameters

4Ah 4 AID (long, MSB first)

The “Select Application” command allows to select one specific application for further access.
If this parameter is 0x00, the PICC level is selected and any further operations are related to this level.
If an application with the specified AID is found in the application directory of the PICC, the subsequent
commands interact with this application.

18
Format PICC (4Bh)

Func Len Parameters

4Bh 0

This command releases the PICC user memory.

Remark:
This command always requires a preceding authentication with the PICC master key.

19
Get Card Version (4Ch)

Func Len Parameters

4Ch 0

This command returns manufacturing related data of the PICC.

Response Version Info (28 bytes):

Field Size (byte) Value
vendor ID 1 0x04 for NXP
type 1 0x01
sub type 1 0x01
H/W major version 1
minor version 1
storage size 1 0x18 = 4096 bytes
protocol type 1 0x05 = ISO14443-2 and -3
vendor ID 1 0x04 for NXP
type 1 0x01
sub type 1 0x01
S/W major version 1
minor version 1
storage size 1 0x18 = 4096 bytes
protocol type 1 0x05 = ISO14443-3 and -4
UID 7
production batch number 5
calendar week of production 1
year of production 1

20
Get File List (4Dh)

Func Len Parameters

4Dh 0

This command returns the File IDentifiers of all active files within the currently selected application.

Response:

Func Len Parameters

ACK n first FID (byte) … n FID (byte)

21
Set / Get File Settings (4Eh)

Func Len Parameters

1 (Get) FID (byte)
4Eh
4 (Set) FID (byte) + Comm. Mode (byte) + Access Right (Int, MSB first)

The “Get File Settings” (len=1) command allows to get information on the properties of a specific file. The
information provided by this command depends on the type of the file which is queried.

Response ( for Get File Settings):

for file type = data file (0x00) or backup file (0x01)
File Comm.
Access Right File Size
ACK Len=8 Type Mode

byte byte Int (MSB first) Long (MSB First)

for file type = value file (0x02)

File Comm. Limited credit Limited credit
Access Right Lower limit Upper limit
Type Mode value enabled
ACK Len=17
Int (MSB
byte byte Long (MSB First) Long (MSB First) Long (MSB first) byte
first)

for file type = linear record file (0x03) or cyclic record file (0x04)
File Comm. Max. number of Current number
Access Right Record size
Type Mode records of records
ACK Len=16
Int (MSB
byte byte Long (MSB First) Long (MSB First) Long (MSB first)
first)

22
The “Set File Settings” (len=4) command changes the access parameters of an existing file.

The Comm. Mode byte:

Communication Mode Bit 7~2 Bit 1 Bit 0
Plain communication RFU ignored 0
Plain communication secured by DES/3DES MACing RFU 0 1
Fully DES/3DES enciphered communication RFU 1 1

The Access Right Field (16 bits):

15 12 11 8 7 4 3 0
Read Access Write Access Read & Write Access Change Access Right
MSB LSB

Each of the Access Rights is coded in 4 bits, one nibble, Each nibble represents a link to one of the keys stored
within the respective application’s key file.

One nibble (4 bits) allows to code 16 different values. If such a value is set to a number between 0 and 13 (max.
14 keys), this references a certain key within the application’s key file, provided that the key exists (selecting a
non-existing key is not allowed).

If the number is coded as 14 (0xE) this means “free access”. Thus the regarding access is granted always with
and without a preceding authentication, directly after the selection of the respective application.

The number 15 (0xF) defines the opposite of “free” access and has the meaning “deny” access. Therefore the
respective linked Access Rights is always denied.

23
Create Std Data File (4Fh)

Func Len Parameters

FID (byte)
Comm. Mode (byte)
4Fh 8
Access Right (int, MSB First)
File Size (long, MSB First)

The “Create Std Data File” command is used to create files for the storage of plain unformatted user data within
an existing application on the PICC.

Remark:
The DESFire internally allocates NV-memory in multiples of 32 bytes. Therefore a file creation command with
“File Size” parameter 0x00000001 (1 byte file size) will internally consume the same amount of NV-memory as
a 32 bytes.

24
Create Backup Data File (50h)

Func Len Parameters

FID (byte)
Comm. Mode (byte)
50h 8
Access Right (int, MSB First)
File Size (long, MSB First)

The “Create Backup Data File” command is used to create files for the storage of plain unformatted user data
within an existing application on the PICC, additionally supporting the feature of an integrated backup
mechanism.

Remark:
 The parameter FID only the first 8 files within an application feature the integrated backup mechanism. (only
FID=0x00 to 0x07 is allowed).
 Due to the mirror image a Backup data file always consumes DOUBLE the NV-memory on the PICC
compared to a Std Data File with the same specified “File Size”.

25
Create Value File (51h)

Func Len Parameters

FID (byte)
Comm. Mode (byte)
Access Right (int, MSB First)
51h 17 Lower Limit(long, MSB first),
Upper Limit(Long, MSB First),
Initial Value(Long, MSB First),
Limited Credit Enabled(byte)

The “Create Value File” command is used to create files for storage and manipulation of 32 bite signed integer
values within an existing application on the PICC.

Remark:
 The upper limit has to be ≧ lower limit, otherwise an error message would be sent by the PICC and thus
the file would not be created.
 The Limited Credit feature, see Limit Credit. Here 0x00 means that “Limited Credit Enabled” is disable and
0x01 enables this feature.
 Value File feature always the integrated backup mechanism. Therefore every access changing the value
needs to be validated using the “Commit Transaction” command.

26
Create Linear Record File (52h)

Func Len Parameters

FID(byte),
Communication Mode(byte),
52h 12 Access Right(int, MSB first),
Record Size(long, MSB first),
Max. Num of Records(long, MSB first)

The “Create Linear Record File” command is used to create files for multiple storage of structural data, for
example for loyalty programs, within an existing application on the PICC. Once the file is filled completely with
data records, further writing to the file is not possible unless it is cleared, see command “Clear Record File”.

Remark:
 Thus the entire file size in the PICC NV-memory is given by “Record Size” x “Max. Num of Records”.
 Linear Record Files feature always the integrated backup mechanism. Therefore every access appending a
record needs to be validated using the “Commit Transaction” command.

27
Create Cyclic Record File (53h)

Func Len Parameters

FID(byte),
Communication Mode(byte),
53h 12 Access Right(int, MSB first),
Record Size(long, MSB first),
Max. Num of Records(long, MSB first)

The “Create Cyclic Record File” command is used to create files for multiple storage of structural data, for
example for loyalty programs, within an existing application on the PICC. Once the file is filled completely with
data records, the PICC automatically overwrites the oldest record with the latest written one. This wrap is fully
transparent for the PCD.

Remark:
 Thus the entire file size in the PICC NV-memory is given by “Record Size” x “Max. Num of Records”.
 Cyclic Record Files feature always the integrated backup mechanism. Therefore every access appending a
record needs to be validated using the “Commit Transaction” command.
 As the backup feature consumes one record, the “Max. Num Of Records” needs to be one largerthen the
application requires.

28
Delete File (54h)

Func Len Parameters

54h 1 FID(byte),

The “Delete File” command permanently deactivates a file within the file directory of the currentlhy selected
application.

Remark:
 Depending on the application master key settings, a preceding authentication with the application master
key is required.
 Allocate memory blocks associated with the deleted file are not set free. The FID of the deleted file can be
re-used to create a new file within that application.
 To release memory blocks for re-use, the whole PICC user NV-memory needs to be erased using the
“Format PICC” command.

29
Read Data (55h)

Func Len Parameters

FID(byte),
55h 9 Offset(long, MSB first),
Length(long, MSB first),

The “Read Data” command allows to read data from Std Data File or Backup Data File.

The Offset parameter is of 4 byte length and codes the starting position for the read operation within the file.
This parameter has to be in the range from 0x00000000 to file size-1.

The Length parameter is also 4 byte long and specifies the number of data bytes to be read. This parameter
has to between in the range from 0x00000000 to 0x00000080. If the Length is coded as 0x00000000, the
entire data file, starting from the position specified in the offset value, is read.

30
Write Data (56h)

Func Len Parameters

FID(byte),
56h 9 Offset(long, MSB first),
Length(long, MSB first),

The “Write Data” command allows to write data to Std Data File or Backup Data File.
Each time the max data size written is 128 bytes.

Remark:
 The “Write Data” command requires a preceding authentication either with the key specified for “Write” or
“Read&Write” access.
 If the “Write Data” operation is performed on a Backup Data File, it is necessary to validate the written data
with a “Commit Transaction” command. An “Abort Transaction” command will invalidate all changes.
 If data is written to Std Data Files (without integrated backup mechanism), data is directly programmed into
the visible NV-memory of the file. The new data is immediately available to any following “Read Data”
command performed on that file.

31
Get Value (57h)

Func Len Parameters

57h 9 FID(byte),

The “Get Value” command allows to read the currently stored value from Value File.

Response:
Value (long, MSB first)

Remark:
 The “Get Value” command requires a preceding authentication with the key specified for Read, Write or
Read&Write access.
 After updating a value file’s value but before issuing the “Commit Transaction” command, the “Get Value”
command will always retrieve the old, unchanged value which is still the valid one.

32
Credit (58h)

Func Len Parameters

FID(byte),
58h 5
Amount(long, MSB first),

The Credit command allows increasing a value in a Value File.

Remark:
 It is necessary to validate the updated value with a “Commit Transaction” command, an “Abort Transaction”
command will invalidate all changes.
 The value modifications of Credit, Debit and Limit-Credit commands are cumulated until a “Commit
Transaction” command is issued.
 The Credit commands do NEVER modify the Limited Credit Value of a Value File. However, if the Limited
Credit value needs to be set to 0, a Limited-Credit with value 0 can be used.
 The Credit command requires a preceding authentication with the key specified for “Read&Write” access.

33
Debit (59h)

Func Len Parameters

FID(byte),
59h 5
Amount(long, MSB first),

The Debit command allows decreasing a value in a Value File.

Remark:
 It is necessary to validate the updated value with a “Commit Transaction” command, an “Abort Transaction”
command will invalidate all changes.
 The value modifications of Credit, Debit and Limit-Credit commands are cumulated until a “Commit
Transaction” command is issued.
 The Credit command requires a preceding authentication with the key specified for Read, Write and
Read&Write access.
 If the usage of the Limited-Credit feature is enabled, the new limit for a subsequent “Limit Credit” command
is set to the sum of Debit commands within one transaction before issuing a “Commit Transaction”
command. This assures that a “Limit Credit” command can not re-book more values than a debiting
transaction deducted before.

34
Limited Credit (5Ah)

Func Len Parameters

FID(byte),
5Ah 5
Amount(long, MSB first),

The “Limited Credit” command allows a limited increase of a value stored in a Value File without having full
Read&Write permissions to the file. This feature can be enabled or disabled during value file creation.

Remark:
 It is necessary to validate the updated value with a “Commit Transaction” command, an “Abort Transaction”
command will invalidate all changes.
 The value modifications of Credit, Debit and Limit-Credit commands are cumulated until a “Commit
Transaction” command is issued.
 The Limited-Credit command requires a preceding authentication with the key specified for Read, Write and
Read&Write access.
 The value for “Limited Credit” is limited to the sum of the Debit commands on this value file within the most
recent transaction containing at least one Debit. After executing the “Limited Credit” command the new limit
is set to 0 regardless of the amount which has been re-booked. Therefore the “Limited Credit” command
can only be used once after a Debit transaction.

35
Write Record (5Bh)

Func Len Parameters

FID(byte),
5Bh 9 Offset (Long, MSB first),
Length (Long, MSB First)

The “Write Record” command allows writing data to a record in a Cyclic or Linear Record File.

The Offset parameter offset within one single record (in byte). This parameter has to be in the range from
0x000000000 to record size-1.

The Length parameter has to be in the range from 0x00000000 to record size - Offset.

Remark:
 The “Write Record” command appends one record at the end of the linear record file, it erases and
overwrites the oldest record in case of a cyclic record file if it is already full. The entire new record is cleared
before data is written to it.
 If no “Commit Transaction” command is sent after a “Write Record” command, the next “Write Record”
command to the same file writes to the already created record. After sending a “Commit Transaction”
command, a new “Write Record” command will create a new record in the record file. An “Abort
Transaction” command will invalidate all changes.
 After issuing a “Clear Record File” command, but before a “Commit Transaction” / “Abort Transaction”
command, a “Write Record” command the same record file will fail.
 The “Write Record” command requires a preceding authentication either with the key specified for “Write” or
“Read&Write” access.

36
Read Records (5Ch)

Func Len Parameters

FID(byte),
5Bh 9 Record#(long, MSB first),
NRecToRead (long, MSB first),

Example: File ID =1
Record# Record Data
0 4444444444
1 3333333333
2 2222222222
3 1111111111

Read Record ( FID=1 , Record#=1 , NRecToRead=2)

Result= 3333333333 and 2222222222

The “Read Record” command allows reading out a set of complete records from a Cyclic or Linear Record File.

The Record# parameter offset of the newest record which is read out. In case of 0x00000000 the latest record
is read out. The Record# value must be in the range from 0 to number of exist records-1.

The “NRecToRead” parameter is another 4 bytes which code the Number of Records. To be Read from the
PICC. Records are always transmitted by the PICC in chronological order (= starting with the oldest, which is
number of records – 1 before the one addressed by the given offset). If this parameter is set to 0x00000000
then all records, from the oldest record up to and including the newest record are read. The allowed range for
the number of records parameter is from 0x00000000 to number of existing records – Record#.

Response:
Return ACK with Record Size (unit: byte).

Remark:
 In cyclic record files the maximum number of stored valid records is one less than the number of records
specified in the “Create Cyclic Record File” command.
 A “Read Records” command on any empty records file will result in an error.
 The “Read Records” command requires a preceding authentication either with the key specified for “Read”
or “Read&Write” access.

37
Clear Record File (5Dh)

Func Len Parameters

5Dh 1 FID(byte)

The “Clear Record File” command allows resetting a Cyclic or Linear Record File to the empty state.

After executing the “Clear Record File” command but before “Commit Transaction”, all subsequent “Write
Record” commands will fail. The “Read Records” command will return the old still valid records.

After the “Commit Transaction” command is issued, a “Read Records” command will fail, “Write Record”
command will be successful. An “Abort Transaction” command will invalidate the clearance.

Remark:
Full “Read&Write” permission on the file is necessary for executing this command.

38
Commit Transaction (5Eh)

Func Len Parameters

5Eh 0

The “Commit Transaction” command allows validating all previous write access on Backup Data Files, Value
Files and Record Files within one application.

The “Commit Transaction” command validates all write access to files with integrated backup mechanisms:
 Backup Data Files
 Value Files
 Linear Record Files
 Cyclic Record Files

Remark:
The “Commit Transaction” is typically the last command of a transaction before the ISO 14443-4 DESELECT
command or before proceeding with another application.

39
Abort Transaction (5Fh)

Func Len Parameters

5Fh 0

The “Abort Transaction” command allows invalidating all previous write access on Backup Data Files, Value
Files and Record Files within one application.

This is useful to cancel a transaction without the need for re-authentication to the PICC, which would lead to
the same functionality.

The “Abort Transaction” command invalidates all write access to files with integrated backup mechanisms
without changing the authentication status:
 Backup Data Files
 Value Files
 Linear Record Files
 Cyclic Record Files

40
Error Code
Hex Code Status Descriptions
0x00 OPERATION_OK Successful operation
0x0C NO_CHANGES No changes done to backup files, Commit Transaction /
Abort Transaction not necessary
0x0E OUT_OF_EEPROM_ERROR Insufficient NV-Memory to complete command
0x1C ILLEGAL_COMMAND_CODE Command code not supported
0x1E INTEGRITY_ERROR CRC or MAC does not mach data
Padding bytes not valid
0x40 NO_SUCH_KEY Invalid key number specified
0x7E LENGTH_ERROR Length of command string invalid
0x9D PERMISSION_DENIED Current configuration / status does not allow the requested
command
0x9E PARAMETER_ERROR Value of the parameter(s) invalid
0xA0 APPLICATION_NOT_FOUND Requested AID not present on PICC
0xA1 APP_INTEGRITY_ERROR Unrecoverable error within application, application will be
disabled *
0xAE AUTHENTICATION_ERROR Current authentication status does not allow the requested
command
0xAF ADDITIONAL_FRAME Additional data frame is expected to be sent
0xBE BOUNDARY_ERROR Attempt to read/write data from/to beyond the
file's/record's limits. Attempt to exceed the limits of a value
file
0xC1 PICC_INTEGRITY_ERROR Unrecoverable error within PICC, PICC will be disabled
0xCA COMMAND_ABORTED Previous Command was not fully completed Not all
Frames were requested or provided by the PCD
0xCD PICC_DISABLED_ERROR PICC was disabled by an unrecoverable error
0xCE COUNT_ERROR Number of Applications limited to 28, no additional
CreateApplication possible
0xDE DUPLICATE_ERROR Creation of file/application failed because file/application
with same number already exists
0xEE EEPROM_ERROR Could not complete NV-write operation due to loss of
power, internal backup/rollback mechanism activated
0xF0 FILE_NOT_FOUND Specified file number does not exist
0xF1 FILE_INTEGRITY_ERROR Unrecoverable error within file, file will be disabled

41
How to Read/Write a File
Write A File

DFxx DESfire Card

HOST
4
Func=0x0A
File Buffer
(128Byte)
1

Write File
3
Commands
DFxx Core

1. Prepare the file data to File Buffer (use func=0x0A Set Register with File Buffer Address)

2. Send Write File (or Record) commands to DFxx.

3. DFxx send the DESfire RF commands to Card.

4. DFxx send file data form buffer when card accept above commands.

Read A File

DFxx DESfire Card

HOST
3
Func=0x09
File Buffer
(128Byte)
4

Read File

Commands
Core

1 2

1. Host send the Read File (or Record) commands to DFxx.

2. DFxx send the DESfire RF commands to Card.

42
3. Card accept and response the file contents to File Buffer.

4. Host send func=0x09 (Get Registers) with File Buffer Address to get the file data from File Buffer.

Remark:
1. Using func 0x60 to get the File Buffer Address of module (or reader); the File Buffer Address will be used in
Get/Set Register commands for File buffer use.
2. Using func=0x09 with File Buffer Address and Length=Zero to get the Maxima File Buffer Size for our
feature module.

43
History

Rev. A (Jason)
August 5, 2008 First Edition

Rev.B (Jason)
January 12, 2010 Add EV1 Support

Rev.C (Terry)
November 4, 2010 Fix some mistake.

Rev.D (Jason)
April 13, 2011 Add Save DESfire Key Command Set. (Page 10, Page 14)

Rev.E (Jason)
Fixed Crypto Type Code. (Page 10)
Add How to Read/Write a File (Page 42~43)
Add Key Version remark (Page 14)

PROMAG ®
GIGA-TMS INC.
http://www.gigatms.com.tw
mailto:[email protected]
TEL : +886-2-26954214
FAX : +886-2-26954213
Office: 8F, No. 31,Lane 169, Kang-Ning St.,Hsi-Chih, Taipei, Taiwan

44