MSDS PFC - 225

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

MATERIAL SAFETY DATA SHEET

No. MSDS : P-222


Revision : 00
Effective Date : 24/08/2010

1. PRODUCT AND COMPANY IDENTIFICATION


Product name : POLYFLOOR EPOXY FLOOR CEMENT PFC - 225
Product use : Based coat
Manufacture’s Name : PT. PROPAN RAYA ICC
Address : JL. GATOT SUBROTO KM 6.5 JATAKE
TANGERANG 15136 BANTEN - INDONESIA
TELP. : + 62-21-5919577 (HUNTING)
FAX. : + 62-21-5919022/24/25
E-mail : + projtk@propanraya.com

2. INGREDIENTS
% Max
INGREDIENTS COMPONENTS CAS # EINECS #
(by weight)
Epoxy Resin 60 25036-25-3 -

3.HAZARD IDENTIFICATION
WARNING
Clear inflammable liquid, potentially hazardous vapors. Can cause eye and skin irritation upon contact. Inhalation
of vapors can cause anesthetic effect leading to death in poorly ventilated areas.
PROTECTIVE MEASURES
Avoid contact with the skin, eyes and wear proper skin protection.

4.FIRST AID MEASURES


GENERAL
In all cases of doubt, or when symptoms persist, seek medical attention. Never give anything by mouth to an
unconscious person.
EYES
Remove contact lenses. Flush eyes with clear running water for 15 minutes while holding eyelids open; if irritation
persists, seek medical attention.
SKIN
Remove contaminated clothing; wash affected area with soap and water; launder contaminated clothing before
reuse; if irritation persists, seek medical attention.
INGESTION
Give two glasses of water for dilution; induce vomiting by sticking fingers down throat; never give anything by
mouth to an unconscious person; seek medical attention.
INHALATION
Remove affected person to fresh air; provide oxygen if breathing is difficult; if affected person is not breathing,
administer CPR and seek emergency medical attention.

5.FIRE FIGHTING MEASURES


GENERAL HAZARDS
Product is flammable. Products of combustion include compounds of carbon, hydrogen and oxygen, including
carbon monoxide.
EXTINGUISHING MEDIA
Carbon dioxide, water fog, dry chemical, chemical foam.
FIRE FIGHTING PROCEDURES
Self - contained respiratory equipment; cool containers to prevent pressure buildup and explosion when exposed
to extreme heat. Caution - material is flammable.

Page 1 of 4
D:\wanti\MSDS\16 section rev-3\MCPC\PFC - 225.doc
MATERIAL SAFETY DATA SHEET

UNUSUAL FIRE AND EXPLOSION HAZARDS


Closed containers can explode due to buildup of pressure when exposed to extreme heat. Vapors may cause a
flash fire or ignite explosively. Vapors may travel a considerable distance to a source of ignition and flash back.
HAZARDOUS COMBUSTION PRODUCTS
Smoke, fumes, oxides of carbon.

6.ACCIDENTAL RELEASE MEASURES


STEP TO BE TAKEN IN CASE MATERIAL IS RELEASE OR SPILLED: CAUTION - FLAMMABLE - Evacuate
and ventilate area; confine and absorb into absorbent; place material into approved containers for disposal; do
not discharge into lakes, ponds, streams, or public waters.

7.HANDLING AND STORAGE


PRECAUTION TO BE TAKEN IN HANDLING AND STORAGE: Keep container closed when not in use; protect
containers from abuse; protect from extreme temperatures. CAUTION - FLAMMABLE - keeps away from all
sources of ignition. “Empty” containers may contain residue, which may form explosive vapors. Do not weld or cut
near empty container that has not been professionally reconditioned. Use non-sparking tools when opening and
closing containers. Maintain well-ventilated work areas to minimize exposure when handling this material.

8.EXPOSURE CONTROL/PERSONAL PROTECTION


VENTILATION SYSTEM
A system of local and/or general exhaust is recommended to keep employee exposures below the Airborne
Exposure Limits. Local exhaust ventilation is generally preferred because it can control the emissions of the
contaminant at its source, preventing dispersion of it into the general work area. Please refer to the ACGIH
document, Industrial Ventilation, A Manual of Recommended practices, most recent edition, for details. Use
explosion-proof equipment.
PERSONAL RESPIRATORS (NIOSH APPROVED)
If the exposure limit is exceeded, a half-face organic vapor respirator may be worn for up to ten times the
exposure limit or the maximum use concentration specified by the appropriate regulatory agency or respirator
supplier, whichever is lowest. A full-face piece organic vapor respirator may be worn up to 50 times the exposure
limit or the maximum use concentration specified by the appropriate regulatory agency or respirator supplier,
whichever is lowest. For emergencies or instances where the exposure levels are not known, use a full-face
piece positive-pressure, air-supplied respirator. Warning: Air-purifying respirators do not protect workers in
oxygen-deficient atmospheres.
SKIN PROTECTION
Wear impervious protective clothing, including boots, gloves, lab coat, apron or coveralls, as appropriate, to
prevent skin contact.
EYE PROTECTION
Maintain eye wash fountain and quick-drench facilities in work area. Use chemical safety goggles and/or full-face
shield where dusting or splashing of solutions is possible.
WORK/HYGIENIC PRACTICES
Practice safe workplace habits. Minimize body contact with this, as well as all chemicals in general.

9.PHYSICAL AND CHEMICAL PROPERTIES


Appearance : Clear liquid
Flash Point : 100°C
Odor : Mild
Solubility : Dilutable in water
PH : -
Specific gravity : 1.00 ± 0.02 g/cc

Page 2 of 4
D:\wanti\MSDS\16 section rev-3\MCPC\PFC - 225.doc
MATERIAL SAFETY DATA SHEET

10. STABILITY AND REACTIVITY


STABILITY CONDITION TO AVOID
Product is stable under normal operating and Extreme temperatures, open flames, spark.
storage conditions.
INCOMPATIBILITY (MATERIAL TO AVOID): water, strong oxidizers, strong acids, strong alkalis.
HAZARDOUS DECOMPOSITION OR BY PRODUCTS: Decomposition will not occur if handle and stored
properly. In case of a fire, oxides of carbon, hydrocarbons, fumes, and smoke may be produced.
HAZARDOUS POLYMERIZATION CONDITION TO AVOID
Will not occur. None

11. TOXICOLOGY INFORMATION


LD50 of Ingredient LC50 of Ingredient Hazard RISK PHRASES
Hazardous Components
(Specify Species and Route) (Specify Species) Symbol Full Text Section 16
>2000 mg/kg >2000 mg/kg
Epoxy Resin Xi, N R-36/38, 43, 51/53
Oral - rat Rabbit
INHALATION
The inhalation of solvent vapor or dust spray may cause irritation of the respiratory tract.
SKIN CONTACT
These components of the preparation have irritating properties. Prolonged or repeated contact with skin or
mucous membrane may result in irritation symptoms such as redness, blistering, dermatitis, etc cases of allergic
skin reactions have been observed.
EYE CONTACT
The liquid splashed in the eyes may cause irritation.
IGNESTION
Ingestion may cause nausea, weakness and central nervous system effects.

12. ECOLOGICAL INFORMATION


No data are available on the adverse effects of this material on the environment. Neither COD nor BOD data are
available. Based on the chemical composition of this product it is assumed that the mixture can be treated in an
acclimatized biological waste treatment plant system in limited quantities. However, such treatment should be
evaluated and approved for each specific biological system. The preparation has been assessed following the
conventional method of the Dangerous Preparations Directive 1999/45/EC and is classified for eco - toxicological
properties accordingly. See section 2 and 15 for details.

13. DISPOSAL CONSIDERATIONS


WASTE DISPOSAL METHOD: Dispose of in accordance with Local, State, and Federal Regulations. This
product may produce hazardous vapors or fumes in a closed disposal container creating a dangerous
environment. Refer to “40 CFR Protection of Environment Parts 260-299” for complete waste disposal
regulations. Consult your Local, State, or Federal Environmental Protection Agency before disposing of any
chemicals. Do not flush to sanitary sewer or waterway.

14. TRANSPORT INFORMATION


Not regulated for transport

Page 3 of 4
D:\wanti\MSDS\16 section rev-3\MCPC\PFC - 225.doc
MATERIAL SAFETY DATA SHEET

15. REGULATORY INFORMATION


In accordance with 91/155/EEC and 93/112/EEC the product is classified and labeled as follows:
DANGER CLASS : Xi, N

RISK PHRASES: SYMBOL (S) SAFETY PHRESES:


R21/22 Harmful in contact with skin and REQUIRED FOR S2 Keep out of the reach of children.
if swall LABEL S16 Keep away from sources of ignition.
R34 Causes burns S23 Do not breathe vapor and spray mist.
R43 May cause sensitization by skin Harmful S24 Avoid contact with skin.
contact S26 In case of contact with eyes, rinse
R51/53 Harmful to aquatic organisms, immediately with plenty of water and seek
may cause long-term adverse medical advice.
effects in the aquatic environment S28 After contact with skin, wash immediately
with plenty of soap and water.
S29 Do not empty into drains.
Dangerous for the S37 Wear suitable gloves.
environment S51 Use only in well ventilated areas.
S57 Use appropriate containment to avoid
environmental contamination.
S60 This material and/or its container must be
disposed of as hazardous waste.

16. OTHERS INFORMATION


Notes and full R-Phrases text
R66 Repeated exposure may cause skin dryness or cracking
R67 Vapors may cause drowsiness and dizziness
HMIS HAZARD RATINGS HEALTH 1 0 = Insignificant
FLAMMABILITY 0 1 = Slight
REACTIVITY 1 2 = Moderate
PERSONAL PROTECTIVE EQUIPMENT B Safety glasses, Gloves 3 = High
4 = Extreme
This information is based on our present states knowledge. It should not therefore be construed as
guaranteeing specific properties of the products described or their suitability for – a particular application.

Date of issue : August 24, 2010

Page 4 of 4
D:\wanti\MSDS\16 section rev-3\MCPC\PFC - 225.doc

You might also like