Scribd
Upload
40 views1 page

Security Keypad Instructions

The document outlines 8 programming options for a keypad including setting new master and user codes, erasing codes, setting door opening time, and setting remote opening time and mode. Setting a new code involves entering programming mode and following prompts to input the new code and addresses.

Uploaded by

George Spg
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
40 views1 page

Security Keypad Instructions

The document outlines 8 programming options for a keypad including setting new master and user codes, erasing codes, setting door opening time, and setting remote opening time and mode. Setting a new code involves entering programming mode and following prompts to input the new code and addresses.

Uploaded by

George Spg
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

There are eight programming options:

1. Set new master code 4. Erase all user codes 7. Set "remote opening" time (1-99s)
2. Set new user code 5. Set door opening time (1-99s) 8. Set "remote opening" to latch mode
3. Erase a user code 6. Set door output to latch mode

1 To set new master code


Enter ** 1-2-3-4 ** The keypad enters programming mode, the red LED flashes
Enter 2 The red LED illuminates for 2 seconds and then flashes
Enter 0-0-0 # The red LED illuminates for 2 seconds and then flashes
Enter new 4-8 digit code This is the new master cod`e, record the number and keep it safe
Enter # The red LED illuminates for 2 seconds and then flashes
Re-enter the new master code The red LED illuminates for 2 seconds and then flashes
Enter #
Enter # To exit programming mode
To set a new master code of 112233
Enter **1-2-3-4 ** 2 000# 112233# 112233# #

2 To set a new user code


Enter **master code ** The keypad enters programming mode, the red LED flashes
Enter 2 The red LED illuminates for 2 seconds and then flashes
Enter address of new user code i.e. 001 (001-200 accepted)
Enter # The red LED illuminates for 2 seconds and then flashes
Enter new 4-8 digit user code This is the new master code, record the number and keep it safe
Enter # The red LED illuminates for 2 seconds and then flashes
Re-enter the new 4-8 digit user code The red LED illuminates for 2 seconds and then flashes
Enter # The new code is added, to add new codes continue from second step, changing the address
each time
When finished enter an additional # to exit programming mode.
To set a new user code of 6626 in address 1
Enter ** master code ** 2 001# 6626# 6626# #
To set a new user code of 6626 in address 1 & 7788 in address 2
Enter ** master code ** 2 001# 6626# 6626# 2 002# 7788# 7788# #

3 To remove an individual user code


Enter ** master code ** The keypad enters programming mode, the red LED flashes
Enter 3 The red LED illuminates for 2 seconds and then flashes
Enter address of user code to be removed i.e. 001 (001-200 accepted)
Enter # The red LED illuminates for 2 seconds and then flashes.
Re-enter address of user code to be removed i.e. 001 (001-200 accepted)
Enter # The red LED illuminates for 2 seconds and then flashes, the code is removed.
Enter # Exit the programming mode

4 To remove all user codes


Enter ** master code ** The keypad enters programming mode, the red LED flashes
Enter 4 The red LED illuminates for 2 seconds and then flashes
Enter master code
Enter # The red LED illuminates for 2 seconds and then flashes. All code addresses are removed
Enter # Exit the programming mode

You might also like