Visit our website: www.accesscontrol.ie or www.act.

eu
(Operator Instructions)
ACTpro 1000 / 2000 Access Control (18-00008-00)
Copyright © 2009 Access Control Technology Ltd.
Tel: +353 (0)1 466 2570 UK Lo-Call: 0845 300 5204
Dublin 24, Ireland.
Unit C1 South City Centre, Tallaght,
ate due to power loss or in the event of fire.
alternate means of escape in the event of the unit failing to oper-
As with any access control system, always ensure that there is an
IMPORTANT
and report any system problems to the Installer immediately .
Ensure that your staff are fully aware of the operation of readers •
Installer.
Ensure that any damaged user cards are replaced , by your •
system.
Ensure that any lost cards are immediately deleted from the •
performance from your Access Control System.
Please find below some useful notes to ensure satisfactory
Access Control Technology thank you for choosing its product.
Good Housekeeping.
QUICK PROGRAMMING GUIDE
4. Changing Operator code.
(for typical Standalone System) . Enter operator code.
1. Enabling cards . Use 0 to scroll to Change Pin menu.
. Enter the operator code. . Press to enter change pin menu.
. Press to enter the user set-up menu. . Use keys 0-9 to enter new pin.
. Press to enter the enable menu. . Use keys 0-9 to verify pin.
For a single card: . The controller will display Accepted , the new pin is set.
. Use 0 to scroll to the desired card. . Use X to exit from the menu.
. Press to enable the card.
For a range of cards: 5. Learning cards onto controller.
. Use keys 0-9 to enter the first card. Press . . The installer must have the learn facility enabled in the
. Use keys 0-9 to enter the last card. Press . Installer menu to allow cards to be learned.
. Use X to exit from the menu. . Enter operator code.
. Press to enter the user set-up menu.
2. Disabling cards . Use 0 to scroll to Learn menu.
. Enter the operator code. . Press to enter learn menu.
. Press to enter the user set-up menu. . Use 0 to scroll to the user number which is required.
. Press 0, then to enter the enable menu. . Press to allow the selected user to be learned.
For a single card: . Swipe the card which you want learned for selected user.
. Use 0 to scroll to the desired card. . User number Accepted is displayed.
. Press to disable the card. . Use X to exit from the menu.
For a range of cards:
. Use keys 0-9 to enter the first card. Press . 6. Entering a batch of cards onto controller.
. Use keys 0-9 to enter the last card. Press . . Enter operator code.
. Use X to exit from the menu. . Press to enter the user set-up menu.
. Use 0 to scroll to Batch Cards menu.
3. Setting Time and Date . Press to enter Batch Cards menu
. Enter the operator code . Use 0 to scroll to an unused batch.
. Use 0 to scroll to “Set Date/Time” . Press to allow the first card in the batch to be programmed.
. Press to select. . Swipe the first card in the batch.
. Use numeric keys 0-9 to Enter the year . Press . Swipe the last card in the batch.
. Repeat for month, day , hour and minute. . Enter the user number to be assigned to the first card
. New time will be displayed. Press to Accept. . Batch Accepted is displayed
. Use X to exit from the menu. . Use X to exit from the menu.
Factory default code: ( Operator: 123456 ). Note: To Program the advanced features of the ACTpro 1000 / 2000 use the
Operating Instructions which are available from the distributor.
 Operator Menu
1 2 3 4 5 6
User Setup Menu navigation in User & Group Setup functions
0 Enable When one of the user or group setup functions
(This is the default code)
Disable User 1 is invoked, the top line of the display will show
Assign Names Disabled the number of the group or user. If a text name
Operator Menu Assign Groups 0
has been entered, this will be shown instead.
0
User Setup
3
Assign Options
Assign PINs User 2 The lower line will show the current setting for
Group Setup Learn Disabled the item that is being configured.
System Log Batch Cards
Control Door One-To-One
3 Pressing the zero key will advance to the next
user or group.
User Tracking Card Validity User 2
Set Date/Time Pressing the accept key will change the state
Enabled
Time Zones 7 for the currently displayed user or group, or
Set Holidays 1 will allow the displayed information to be
Issue Number Group Setup
User 2
changed (for example, editing the name).
Change PIN 0
Enable From User 5_ As a short cut, on some menus it is possible
7 Disable to use the numeric keys to directly enter a
Assign Names
2
3 7 range of users on which the desired changes
will be made. The prompts "From User" and
Access Rights User 2 "To User" are displayed.
Control Door* Assign Options To User 27_
0
Lock Door Assign PINs On other menus, the numeric keys may be used to
3
jump quickly to a particular user or group number. In
Unlock Door 7
this case the prompt "Goto" is displayed.
Normalise Door User 27
Pass Door System Log Enabled The X key will exit from the current function and
Aux Output On 0
Display Log 7
return to the previous menu.
Aux Output Off Print Log
7 Filter Log
*On the ACT2000 you will first be prompted
Changing PIN codes
7
to select which door to control.
Several menus require a PIN code to be entered or
Entering Text 1 abcABC1 Enter new PIN changed, such as the "Change PIN" function in the
Operator menu, or the "Assign PINs" functions in
Several menus allow text names to 2 defDEF2 the User and/or User Setup menus.
be entered for users or groups. 4 5 6 7
3 ghiGHI3 The controller initially prompts for the new PIN to be
When editing text, the numeric keys 1 Verify PIN
to 9 are used to enter the required entered. The display indicates how many digits are
4 jklJKL4 required, usually 4 or 6.
characters. Each cycles through a
sequence of characters or digits when 5 mnoMNO5 4 5 6 7
pressed. When the new PIN is entered, the controller prompts
Verify PIN for the code to be verified to ensure that no mistakes
3
accepts the entered text.
6 pqrPQR6 have been made. Assuming all is OK, the controller
Accepted will display "Accepted" - the new PIN is now set.
7 stuvSTUV7
0 moves to the next character. or
User and Group PINs may be unset (removed) by
moves to the previous character. 8 wxyzWXYZ8
8
If pressed on the first character, Verify PIN entering a PIN consisting of all zeros.
then the option "Clear ?" is given. 9 (SPC) - & . + ' / 9 0 Not Allowed