SCALA XPRESS

SCALA XPRESS
Table of contents

1 4
SCALA XPRESS

Fume hoods and Storage cupboards

exhaust devices Underbench unit for sinks 50
Overbench cabinet 53
Bench-mounted fume hood 5
Laboratory cabinet 55
Low ceiling bench-mounted
Emergency cabinet 59
fume hood 6
Top-mounted cabinet 60
Fume hood with side installation
Pull-out cabinet 61
made of steel, SI 3 steel 7
Laboratory cabinet
Walk-in fume hood
for storing acids and alkalis 63
with side installation 8
Underbench safety unit
AKKURAT 9
for fume hoods
Secuflow EN7 fume hood
for storing acids and alkalis 65
for high thermal loads 10
FWF 90 underbench safety unit
MobilAir 12
for fume hoods
Underbench unit extraction system 15
for storing flammable liquids 67
Extraction arm 16
Waste disposal system for solid
Extractor hood 17
matter and domestic waste 69

2
FWF 90 safety cabinet
for storing flammable liquids 71
Service modules G 90 gas cylinder cabinet 73

5
Service duct element 18
Service spine
for wall bench / double bench 19 Services
Suspended service boom 21
Mechanical Services 78
Service distribution terminal 23
Electrical services 79
Service wall duct 24

6
Bench-mounted service duct 25

3 Laboratory benches
and sinks
Accessories
Pegboard
Pegboard for service duct
80
80
System step ladder 81
Bench with H-frame 28 Step ladder 81
Bench with C-frame 29 Towel dispenser, plastic 82
Bench with cantilever frame 30 Towel dispenser, aluminium 82
Mobile table 31 Soap dispenser 82
Height-adjustable table 32 Boxes for small parts 83
Worktop material 33 Paper towel dispenser 83
Laboratory sink 38 Monitor arm 84
Drip cup on service spine 39 Name tag 84
Balance table 40 Pipette holder with insertion holes 85

4
Pipette holders with mounting rail 85
Scaffold points for fume hoods 86
Storage cupboards Scaffold rod 86
Emergency cabinet 87
Underbench unit on plinth 42 Lateral pillars 88
Underbench unit on castors 44 Rack 89
Suspended underbench unit 46 Drawer insert type B tray set 90
Push-in underbench unit Drawer insert type A 92
for fume hoods 48 Bimos chair 97
Rinsing units 97
 SCALA XPRESS
Bench-mounted fume hood
1
Intended use Dimensional drawing

Fume hoods and exhaust devices

„„Protective device for the user, tested in acc. with
EN 14175
„„Extraction of fumes, aerosols and dust from the

internal workspace to prevent dangerous amounts

of pollutants from escaping into the laboratory
„„Reduced risk of the formation of a high

concentration of hazardous substances /

hazardous explosive atmosphere in the internal
workspace
„„Protection from splashes of hazardous substances

„„Protection from flying particles, bodies or parts

escaping from the internal workspace

„„General fume hoods constructed in acc. with

EN 14175 are normally not suited for use with

radioactive substances or microorganisms
„„Not suitable for openly breaking down chemicals

„„Service outlets in the rear panel of the internal

workspace
„„Control units located horizontally on the service

rail of the support unit

Technical data
Dimensions 1200 1500 1800 2100
Width [mm] 1200 1500 1800 2100
Depth [mm] 900
Height [mm] 2700
Clear width, internal workspace [mm] 1150 1450 1750 2050
Clear height, internal workspace [mm] 1550
Working height [mm] 900

Weight 1200 1500 1800 2100

Without installation [kg] Approx. 250 Approx. 300 Approx. 350 Approx. 400

Options
Secuflow Optional
Extraction hood diameter 250 mm and 315 mm
Sash controller Optional
Inner lining Melamine or Solid Grade Laminate
Stoneware (10 weeks)
Side execution Glass panel and / or cable through-put
Worktop Stoneware; Drip cup in rear wall only
Service supply Electrical services: Please refer to section 5 (Services) Electrical supply for country specification
Mechanical services: Up to 3 different gases / water. Multiple connections are also possible,
depending on the existing equipment. Please refer to section 5 (Services)
Service supply from above by default, if no other indication. Please do always indicate the
connection point on technical drawings.
Illuminighting Downlight
Safety glass ESG and VSG
Airflow monitoring FAZ / AC4 without BUS connection
Material B2 Standard

! No sinks can be incorporated in the worktop!

5
1 SCALA XPRESS
Low ceiling bench-mounted fume hood

Intended use Dimensional drawing

Fume hoods and exhaust devices

„„Protective device for the user, tested in acc. with

EN 14175
„„Extraction of fumes, aerosols and dust from the

internal workspace to prevent dangerous amounts

of pollutants from escaping into the laboratory
„„Reduced risk of the formation of a high

concentration of hazardous substances /

hazardous explosive atmosphere in the internal
workspace
„„Protection from splashes of hazardous substances

„„Protection from flying particles, bodies or parts

escaping from the internal workspace

„„General fume hoods constructed in acc. with

EN 14175 are normally not suited for use with

radioactive substances or microorganisms
„„Not suitable for openly breaking down chemicals

„„Service outlets in the rear panel of the internal

workspace
„„Control units located horizontally on the service

rail of the support unit

„„Suitable for rooms with low ceiling height

Technical data
Dimensions 1200 1500 1800 2100
Width [mm] 1200 1500 1800 2100
Depth [mm] 900
Height [mm] 2400 + 285 mm with 900 mm sash opening
Clear width, internal workspace [mm] 1150 1450 1750 2050
Clear height, internal workspace [mm] 1250
Working height [mm] 900

Weight 1200 1500 1800 2100

Without installation [kg] Approx. 220 Approx. 260 Approx. 300 Approx. 350

Options
Secuflow Optional
Extraction hood diameter 250 mm and 315 mm
Sash controller Optional
Inner lining Melamine or Solid Grade Laminate
Stoneware (10 weeks)
Side execution Glass panel and / or cable through-put
Worktop Stoneware; Drip cup in rear wall only
Service supply Electrical services: Please refer to section 5 (Services) Electrical supply for country specification
Mechanical services: Up to 3 different gases / water. Multiple connections are also possible,
depending on the existing equipment. Please refer to section 5 (Services)
Service supply from above by default, if no other indication. Please do always indicate the
connection point on technical drawings.
Illuminighting Downlight
Safety glass ESG and VSG
Airflow monitoring FAZ / AC4 without BUS connection
Material B2 Standard

6 ! No sinks can be incorporated in the worktop!

 SCALA XPRESS
Fume hood with side installation, made of steel
1
SI 3 steel
Intended use Dimensional drawing

Fume hoods and exhaust devices

„„Protective equipment for users, tested in
accordance with EN 14175 and ASHRAE 110-
2005.
„„Extraction of fumes, aerosols and dust from

the internal workspace to prevent dangerous

concentrations of pollutants from escaping into
the laboratory

AC 3262
„„To prevent the formation of dangerous potentially

FAZ 2420
explosive atmospheres in the internal workspace
„„Protection from splashes of hazardous substances

„„Protection from flying particles, bodies or parts

from the internal workspace

„„General purpose fume hoods constructed in

compliance with with EN 14175 and ASHRAE

110-1005 are normally not suited for use with
radioactive substances or micro-organisms
„„Not suitable for openly breaking down chemicals

„„Service outlets in the side panel of the internal

workspace
„„Control units located externally on the service

panels

Technical data
Dimensions 1200 1500 1800 2100 2400
Width [mm] 1200 1500 1800 2100 2400
Depth [mm] 900
Height [mm] 2400
Clear internal width of internal space [mm] 940 1240 1540 1840 2140
Clear internal height of internal space [mm] 1345
Working height [mm] 900

Weight 1200 1500 1800 2100 2400

Without installation [kg] Approx. 220 Approx. 290 Approx. 350 Approx. 410 Approx. 470

Options
Inner lining Solid grade laminate, Polypropylene
Worktop Epoxy; Drip cup in side wall only
Service supply Electrical services: Please refer to section 5 (Services) Electrical supply for country
specification
Mechanical services: Up to 3 different gases / water. Multiple connections are also possible,
depending on the existing equipment. Please refer to section 5 (Services)
Service supply from above by default, if no other indication. Please do always indicate the
connection point on technical drawings.
Illuminighting Downlight
Safety glass ESG and VSG
Airflow monitoring FAZ / AC4 without BUS connection

! No sinks can be incorporated in the worktop!

7
1 SCALA XPRESS
Walk-in fume hood with side installation

Intended use Dimensional drawing

Fume hoods and exhaust devices

„„Protective device for the user, tested in acc. with

EN 14175
„„Extraction of fumes, aerosols and dust from the

internal workspace to prevent dangerous amounts

of pollutants from escaping into the laboratory
„„To prevent the formation of dangerous potentially

explosive atmospheres in the internal workspace

„„Protection from splashes of hazardous substances

„„Protection from flying particles, bodies or parts

escaping from the internal workspace

„„General fume hoods constructed in acc. with

EN 14175 are normally not suited for use with

radioactive substances or microorganisms
„„Not suitable for openly breaking down chemicals

„„Suitable for barrier-free entering of the internal

workspace
„„Service outlets in the service modules of the side

panels of the internal workspace

„„Control units located vertically on the side service

panels
„„Suitable for high experimental set-ups

Technical data
Dimensions 1200 1500 1800 2100 2400
Width [mm] 1200 1500 1800 2100 2400
Depth [mm] 900
Height [mm] 2700
Clear width, internal workspace [mm] 950 1250 1550 1850 2150
Clear height, internal workspace [mm] 2450

Weight 1200 1500 1800 2100 2400

Without installation [kg] Approx. 320 Approx. 390 Approx. 450 Approx. 510 Approx. 570

Options
Extraction hood diameter 250mm and 315mm
Sash controller Optional
Inner lining Melamine or Solid Grade Laminate
Stoneware (10 weeks)
Side execution Glass panel and /or cable through-put
Worktop None; Drip cup in side wall only
Service supply Electrical services: Please refer to section 5 (Services) Electrical supply for country specification
Mechanical services: Up to 3 different gases / water. Multiple connections are also possible,
depending on the existing equipment. Please refer to section 5 (Services)
Service supply from above by default, if no other indication. Please do always indicate the
connection point on technical drawings.
Illuminighting Downlight
Safety glass ESG and VSG
Airflow monitoring FAZ / AC4 without BUS connection
Material B2 Standard

8
 SCALA XPRESS
AKKURAT
1
Intended use Dimensional drawing

Fume hoods and exhaust devices

„„Protects the chemist from any kind of air borne
particles or aerosols
„„Allows quick and precise calibration whilst the

usage of highly sensitive microbalances

„„Fullfills the highest quality and safety standards

1450
1200/1500 677

Technical data
Dimensions 1200
Width [mm] 1200
Depth [mm] 650
Height [mm] 1450
Clear width of internal space [mm] 1155
Effective depth of internal space [mm] 575
Clear internal height of internal space [mm] 530
Working Height [mm] 900

Weight 1200
Without installation [kg] 120

Ventilation technology
Filtration HEPA Filter H14 acc. DIN EN 1822
Connecting diameter Ø [mm] 160
Air exchange rate [m³/h] 140
Pressure drop [PA] 80
Connection voltage [V] 230
Power consumption [W] 250

9
1 SCALA XPRESS
Secuflow EN7 fume hood for high thermal loads

Intended use Dimensional drawing

Fume hoods and exhaust devices

„„For working with high thermal loads in the internal

workspace (heat sources of 4 KW per metre of clear
width in the fume hood)
„„Protective device for the user, tested in acc. with DIN

EN 14175-7:2012
„„Extraction of fumes, aerosols and dust from the

internal workspace to prevent dangerous amounts

of pollutants from escaping into the laboratory
„„Reduced risk of the formation of a high

concentration of hazardous substances / hazardous

explosive atmosphere in the internal workspace
„„Protection from splashes of hazardous substances

„„Protection from flying particles and compounds

from the internal workspace

„„Fume hoods which are built in accordance with

EN 14175 are not permitted for working with

radioactive substances and microorganisms
„„Not suitable for openly breaking down chemicals

„„Active supportive flow technology (Secuflow

technology) reduces the energy consumption while

regulations and standards are observed
„„Service outlets for sanitary supply in the rear panel

of the internal workspace

„„Control units located on the exterior of the support

Technical data
Dimensions 1200 1500 1800
Width [mm] 1200 1500 1800
Depth [mm] 900
Height [mm] 2700
Clear internal width of internal space [mm] 1150 1450 1750
Clear internal height of internal space [mm] 1550
Working height [mm] 900

Weight 1200 1500 1800

Without installation [kg] Approx. 250 Approx. 300 Approx. 350

Design characteristics 1200 1500 1800

Supporting construction Self-supporting underbench units or H-frame with push-in underbench units
Sash 2 horizontal sashes 3 horizontal sashes
Side panel of the fume hood full
Max. number of devices for scaffold points, 9 12
dia. 12 mm up to 13 mm
Max. load per scaffold point with scaffold rod 5
length 300 mm [kg]
Service modules 2 3

10
 SCALA XPRESS
Secuflow EN7 fume hood for high thermal loads
1

Fume hoods and exhaust devices

Electrics
Electrical supply External sockets in service panels
Fuse box Optional
Sash controller SC Optional

Sanitary technology
Sanitary supply Service modules with take-off valves for vacuum, gases and/or waters and integrated
sink (PP) as an option

Ventilation technology 1200 1500 1800

Air flow range without/with thermal load 450/700 450/750 540/900
[m³/h] 1)
Function display FAZ
with temperature monitoring
Airflow damper, constant Airflow-Controller AC
with temperature monitoring
Airflow damper, variable Airflow-Controller AC
with temperature control
Detector of sash position Only variable with Airflow-Controller AC
Connection height [mm] for FAZ with 2570
extraction hood dia. 250 mm
Connection height [mm] for FAZ with 2570
extraction hood dia. 315 mm 2)
Connection height [mm] for AC with 2950
extraction hood dia. 250 mm
Connection height [mm] for AC with 2790
extraction hood dia. 315 mm 2)
Underbench unit extraction system As an option, depending on requirements and regulations
1)
All air volume specifications refer to an opening height of the sash window of 500 mm (Test opening in accordance with EN14175) and the recommended maximum
trace gas values of BG Chemie.
2)
In order to minimise noise and pressure losses, for air volumes >1000 m³/h Waldner recommends the extract manifold with a connection diameter of 315 mm.
A maximum admission pressure of 600 Pa should not be exceeded with fume hoods with airflow dampers.
The indicated minimum air exchange rates were determined under specified test conditions in acc. with EN 14175-3. These minimum air exchange rates must be
adapted when dimensioning the ventilation system.
If on-site extract air monitoring systems or airflow dampers are used, the required air volumes may be different. The operating limitations must be agreed upon with
Waldner.

Material/surface
Worktop Stoneware
Internal lining Melamine resin facing
Solid (grade) laminate
Stoneware

! No sinks can be incorporated in the worktop!

! Secuflow EN7 is only available with the 10-week programme!

11
1 SCALA XPRESS
MobilAir

Intended use
Fume hoods and exhaust devices

„„Can be used where required (only in air-circulating mode)

„„Control units located externally
„„Not suitable for openly breaking down chemicals

„„Not suitable as a replacement for bench-mounted fume hoods in acc. with EN 14175

Design
Air-circulating mode

1
6
7

1 Sash with handle

2 FAZ control panel
3 Removable fascia panel
4 Filter housing with ventilator in
air-circulating mode
5 Rear panel with air guiding
profile
6 Material lock
7 Sockets

12
 SCALA XPRESS
MobilAir
1
Extract air operation

Fume hoods and exhaust devices

4
3

1
6
7

1 Sash with handle

2 FAZ control panel
3 Removable fascia panel
4 Extract air spigot
5 Rear panel with air guiding
profile
6 Material lock
7 Sockets

Technical data
Dimensions
Width [mm] 900
Depth [mm] 600
Height with sash closed/open [mm] 1215/1620
Access width [mm] 730
Clear width, internal workspace [mm] 850
Effective depth [mm] 503
Clear internal height up to lamp [mm] 846
Clear internal height up to ceiling [mm] 935

Weight
MobilAir for extract air operation [kg] Approx. 70
MobilAir for air-circulating mode incl. filter Approx. 82
[kg]

13
1
Fume hoods and exhaust devices SCALA XPRESS
MobilAir

Design characteristics
Air-circulating mode With ventilator and filter
Extract air operation Extract air spigot connected to on-site extract air system
Lighting Dazzle-free, can be switched from the outside
Sash Moves vertically
Material lock Possible on the left and/or right side of the fume hood

Electrics
Electrical supply 2 external sockets
Total power of sockets [W] 1000
Connection voltage [V AC] 230
Lighting [W] 13
Ventilator power [W] 115

Ventilation technology
Minimum air exchange rate [m³/h] 300
Function display FAZ as an option
Connection height [mm] Extract air spigot Ø 125 mm 1137

Material
Side panel design, sash Plexiglas

Filter type „A“ no.5, gas filter

Dimensions [mm] 610 x 305 x 150 (+ 8 mm seal)
Pressure loss [Pa] at 300 m³/h 130
Design characteristics Gas filter cell with 5 layers of activated carbon mat, type „A“; MDF frame; with white-
painted grid on both sides, with grip and type label on the 610-mm-side, PU seal on
the dust-laden air side
Use Separable substances: organic gases and vapours (e.g. solvents, petrol fumes, toluol,
benzol, kerosine, odours, hydrocarbons with mass weights 30 and higher), cold, non-
boiling (VOC, high-boiling substances)

Filter type „BEP“, gas and particle filter

Dimensions [mm] 610 x 305 x 150 (+ 8 mm seal)
Pressure loss [Pa] at 300 m³/h 240
Design characteristics Combination filter Hepa H13 with activated carbon mat and particle filter, type „BEP;
MDF frame, with white-painted grid on both sides, with grip and type label on the
610-mm-side, PU seal on the dust-laden air side
Use Separable substances: inorganic gases and vapours (e.g. chlorine, hydrosulphides,
sulphur dioxide, hydrogen chlorides, cold and heated). Molecules and particle
separation 99.95 % MPPS

Filter type „P“, particle filter cell

Dimensions [mm] 610 x 305 x 150 (+ 8 mm seal)
Pressure loss [Pa] at 300 m³/h 150
Design characteristics Particle filter, type „P“, Hepa H13, Midilar MDSA; MDF frame, with white-painted grid
on both sides, with grip and type label on the 610-mm-side, fold height 45 mm, PU
seal on the dust-laden air side, filter medium flush on the dust-laden air side
Use Separable substances: Particle separation 99.95 % MPPS, Hepa H13

! MobilAir is only available with the 10-week programme!

14
 SCALA XPRESS
Underbench unit extraction system
1
Intended use Design

Fume hoods and exhaust devices

„„For the extraction of safety cabinets (underbench
units) used for the storage of hazardous materials
„„For the extraction of underbench units in service
1

spines and fume hoods

1 Extract air spigot

Technical data
Ventilation technology
Air exchange rate [m³/h] 40
Ventilation connection (ascending duct) 90
Ø [mm]

Material
Ventilating pipe PPS

15
1 SCALA XPRESS
Extraction arm

Intended use Design

Fume hoods and exhaust devices

„„For the extraction of a specific area

„„For fixing to service spines or the wall

1 Extraction arm

Technical data
Dimension 50 75
Pipe system Ø [mm] 1)
50 75
Coupling hood Ø [mm] 350
Extraction maximum [mm] 50 75
1)
Pipe system Ø 50 mm only for fastening to the service wing

Ventilation technology 50 75
Minimum air exchange rate [m³/h] 50 100
Admission pressure [Pa] 150
Admission pressure [Pa] with Waldner airflow 200
damper

Material
Pipe Anodised aluminium
Hinged bracket Polypropylene
Coupling hood Polycarbonate
Suction tip Anodised aluminium

16
 SCALA XPRESS
Extractor hood
1
Intended use

Fume hoods and exhaust devices

„„For the extraction of a specific area
„„For fixing to service spines and to the wall

Design

1 Extractor hood

Technical data

Dimensions 1200 1500

Width [mm] 1200 1500
Height x depth [mm] 300 x 600
Extract air spigot Ø [mm] 200

Ventilation technology 1200 1500

Minimum air exchange rate [m³/h] 480 600
Admission pressure [Pa] 25 30
Admission pressure [Pa] with Waldner airflow 150
damper

Material
Extractor hood Polypropylene

17
2 SCALA XPRESS
Service duct element

Intended use
Service modules

„„Services supply at laboratory workstations

„„Integration of all service outlets including sockets and multiple connectors for information technology
„„Expansion and modification of the services supply through clip-in service panels

„„Use in service spines, service wall ducts, suspended service booms and bench-mounted service ducts

„„Tool-free installation of supplementary service duct add-on parts such as pegboard, monitor arm, pipette

holder, paper towel dispenser, universal storage area, etc.

Design

1 Service panel with corner valves

2 Storage area
3 Service panel with sockets
3
4 Accessory rail for the tool-free
installation of add-on parts
4

Service panel variants

1 2 3 4

1 Service panel with corner valves

2 Service panel with 8 sockets of the same type
3 Service panel with different types of sockets
4 Service panel with automatic circuit breakers

Technical data
Material
Electrical services Please refer to section 5 (Services) for your country specific services
Mechanical services Service panel with take-off valves for vacuum, gases and/or waters
Services supply depending on the combination with other service modules
Placement on panel max. 5 technical gases /water or max. 2 pure gases.
For further specification refer to section 5 (Services)
Service supply From above by default,
if no other indication on technical drawings

18
 SCALA XPRESS
Service spine for wall bench / double bench
2
Dimensional drawing

Service modules
Technical data
Dimensions
Width [mm] 600 900 1200 1500 1800
Depth, service spine for wall bench [mm] 75
(incl. wall bench) (750/900)
Depth, service spine for double bench [mm] 92
(incl. double bench) (1500/1800)
Height [mm] 1790
Working height [mm] 750
900
Height, pillar extension [mm] 462
for overbench cabinet, height 460 mm
Height, pillar extension [mm] 762
for overbench cabinet, height 760 mm
Height, pillar extension [mm] Depending on ceiling height
up to ceiling height 3500 mm
Service panel, width x height [mm] 300 x 200
Glass shelf, width x depth [mm] Width, service spine x 150
Shelf of OSB board, width x depth [mm] Width, service spine x 300

19
2 SCALA XPRESS
Service spine for wall bench / double bench

Technical data
Service modules

Load bearing capacity

Glass shelf [kg] 20
Shelf of OSB board [kg] 30
Max. load per scaffold point with scaffold rod 5
length 300 mm [kg]

Design characteristics
Modular design Wall bench can be equipped on one side, double bench can be equipped on two sides
Multipurpose uprights can be extended with service duct, e.g. for overbench cabinets
Worktop, cantilever and underbench unit can be replaced without dismounting the
installations
Grid-independent mounting of accessories
Scaffold points ø [mm] 12 to 13
Number of service panels Depending on the width of the service duct

Electrics
Electrical supply Sockets in the service panel
Fuse box Optional

Sanitary technology
Sanitary supply Service panel with take-off valves for vacuum, gases and/or waters
The supply pipes and cables are routed underneath the worktop or cantilever

Options
Options Wall bench or free standing

20
 SCALA XPRESS
Suspended service boom
2
Intended use

Service modules
„„Services supply from the ceiling for:
XXLaboratory benches below the suspended service boom
XXLaboratory equipment on mobile tables or underbench constructions

XXFloor-mounted laboratory equipment

„„Design versions for genetical engineering areas

„„Modular fastening of boom add-on parts to the supporting construction, e.g. glass shelves and OSB

board, scaffold points, etc.

„„Tool-free installation of supplementary service duct add-on parts such as monitor arm, pipette holder,

paper towel dispenser, universal storage area, etc.

Design

1 Service panel with sockets

2 Service panel with corner valves
3 Shelf of OSB board
4 Media supply duct
5 Ceiling stator
6 Functional element
7 Glass shelf
8 Pillar
9 Storage area (service duct) 5
10 Service duct element

3 7

2
9

10
1
10

21
2 SCALA XPRESS
Suspended service boom

Technical data
Service modules

Dimensions
Width [mm] 600 900 1200 1500 1800
Depth [mm] without pillars 350
Depth [mm] with pillars 471
Recommended min. height [mm] bottom edge 1750
of suspended service boom to upper edge of
finished floor
Height, supporting construction Depending on ceiling height
(max. up to ceiling height 4000 mm)
Service panel, width x height [mm] 300 x 200
Glass shelf, width x depth [mm] Width, suspended service boom x 150
Shelf of OSB board, width x depth [mm] Width, suspended service boom x 300

Load bearing capacity

Maximum permissible load [kg] 120
Additional max. load bearing capacity, 30
suspended service boom [kg] per grid
Glass shelf [kg] 20
Shelf of OSB board [kg] 30
Max. load per scaffold point with scaffold rod 5
length 300 mm [kg]

Design characteristics
Construction Functional elements to take up service ducts fastened to the ceiling and connected
Number of service panels (per side) Depending on the width of the service duct
Scaffold points ø [mm] 12 to 13

Material
Storage area (service duct) Solid grade laminate 5 mm

Electrics
Electrical supply Sockets in the service panel
Fuse box Optional

Sanitary technology
Sanitary supply Service panel with take-off valves for vacuum, gases and/or waters
Supply pipes and cables in supply duct from above

22
 SCALA XPRESS
Service distribution terminal
2
Intended use

Service modules
„„Services supply for clamping to a laboratory workstation
„„The station is supplied through a service module which is fastened to the ceiling, such as suspended
service boom, service column, service wing, service ceiling or a floor-mounted service spine

Design
1 Connection to several service modules
2 Clamping system
3 Service distribution terminal with sanitary installation
4 Plinth element
1 5 Service distribution terminal with 4 sockets

3 5

Technical data
Dimensions
Width [mm] 158
Depth [mm] 118
Height [mm] 205
Height incl. plinth element [mm] 310
Service panel, width x height [mm] 150 x 200
Clamping area [mm] 10 – 100

Design characteristics
Construction Clamping system for worktop or other frames
Services supply via service modules or service spines mounted to the ceiling
Tension relief for pipes and cables between the service distribution terminal and service
module unit through service beam and straps
Cables and hoses are connected to the service module by means of plug-in couplings

Electrics
Electrical supply Max. of 4 sockets 230 V per service panel

Sanitary technology
Sanitary supply Various take-off valves for vacuum, gases or compressed air
Max. number of corner valves per service panel 2
Max. number of high purity gas valves per 1 or 2 (depending on the type and function)
service panel

23
2 SCALA XPRESS
Service wall duct

Intended use
Service modules

„„Wall-mounted services supply for:

XXLaboratory
benches under or in front of the service wall duct
XXLaboratory equipment on mobile tables or underbench constructions

XXFloor-mounted laboratory equipment

„„Design versions for genetical engineering areas

„„Tool-free installation of supplementary service duct add-on parts such as monitor arm, pipette holder,

paper towel dispenser, universal storage area, etc.

Design
3

1
4

1 Service panel with sockets

2 Service panel with corner valves 5
3 Storage area, service wall duct
4 Media supply from above 6
5 Fastening profile/media supply
6 Service duct element

Technical data
Dimensions
Width [mm] 600 900 1200 1500 18001)
Depth [mm] 184
Height [mm] 252
Service panel, width x height [mm] 300 x 200
1)
The service wall duct can be extended as desired in grid lengths of 300 mm.

Load bearing capacity

Storage area [kg] 20 per installed grid

Design characteristics
Construction Service duct for wall mounting incl. solution for inside corner
Number of service panels Depending on the width of the service duct

Material
Storage area Solid grade laminate shelf 5 mm

Electrics
Electrical supply Service panel with sockets
Fuse box Optional

Sanitary technology
Sanitary supply Service panel with take-off valves for vacuum, gases and/or waters
Supply pipes in the fastening profile

24
 SCALA XPRESS
Bench-mounted service duct
2
Intended use

Service modules
„„Services supply of double work benches
„„Design versions for genetical engineering areas
„„Modular fastening of cell add-on parts to the multipurpose uprights, e.g. glass shelves and OSB board,

overbench cabinets, scaffold points, etc.

„„Tool-free installation of supplementary service duct add-on parts such as pegboard, monitor arm, pipette

holder, paper towel dispenser, universal storage area, etc.

„„Not suitable for double benches where separate work surfaces are required (see also BGI/GUV-I 850-0)

Design
Bench-mounted service duct with cantilever frame
and suspended underbench unit

5
3
6
2
7

1 8

1 Worktop
2 Drip cup with water outlet
3 Service panel with sockets
4 Service panel with corner valves
5 Storage area, service duct
6 Service duct element 9
7 Multipurpose upright
8 Media supply duct
9 Suspended underbench unit

! B
 ench Mounted Service Duct cannot be combined with stoneware
worktop, as cutouts are not possible!

25
2 SCALA XPRESS
Bench-mounted service duct

Bench-mounted service duct with overbench cabinets,

Service modules

H-frame and underbench units on castors

Bench-mounted service duct with overbench cabinets,

pillar extension and underbench units on plinth

26
 SCALA XPRESS
Bench-mounted service duct
2
Technical data

Service modules
Dimensions
Width [mm] 600 900 1200 1500 1800
Depth [mm] 310
Height [mm] 1602
Height, opening at working height 450
900 mm [mm]
Height, pillar extension [mm] 462
(for overbench cabinet, height 460 mm)
Height, pillar extension [mm] 762
(for overbench cabinet, height 760 mm)
Height, pillar extension [mm] Depending on ceiling height
(up to ceiling height 3500 mm)
Service panel, width x height [mm] 300 x 200
Glass shelf, width x depth [mm] Width, bench-mounted unit x 150
Shelf of OSB board, width x depth [mm] Width, bench-mounted unit x 300

Load bearing capacity

Glass shelf [kg] 20
Shelf of OSB board [kg] 30
Max. load per scaffold point with scaffold rod 5
length 300 mm [kg]

Design characteristics
Construction Double-sided service duct as bench-mounted unit with opening above the worktop
Number of service panels Depending on duct width
Scaffold points ø [mm] 12 to 13

Material
Storage area, service duct Solid grade laminate shelf 5 mm

Electrics
Electrical supply Sockets in the service panel
Fuse box Optional

Sanitary technology
Sanitary supply Service panel with take-off valves for vacuum, gases and/or waters
Supply pipes in the bench-mounted unit

27
3 SCALA XPRESS
Bench with H-frame

Intended use
Laboratory benches and sinks

„„Benchframe with worktop made of various materials as a work surface and storage area for laboratory
work
„„Supporting construction for analytical equipment and superstructures

Design

Technical data
Dimensions
Width [mm] 600 900 1200 1500 1800
Depth [mm] 600
750
900
Working height [mm] 750
900

Load bearing capacity

H-frame [kg] 200 (for fixing to the wall or for fixing to a service spine)

Design characteristics
Construction For suspended underbench units, cannot be moved for all kinds of frames
For underbench units on castors
Height-adjustable feet Individually adjustable

Material
Bench frame Steel profile 60/25/2 mm
Worktop Depending on requirement
Height-adjustable feet Plastic housing with steel spindle

28
 SCALA XPRESS
Bench with C-frame
3
Intended use

Laboratory benches and sinks

„„Benchframe with worktop made of various materials as a work surface and storage area for laboratory
work
„„Supporting construction for analytical equipment and superstructures

Design

Technical data
Dimensions
Width [mm] 600 900 1200 1500 1800
Depth [mm] 600
750
900
Working height [mm] 750
900

Load bearing capacity

C-frame [kg] 200

Design characteristics
Construction For suspended underbench units, can be moved for all kinds of frames
For movable underbench units
Height-adjustable feet Individually adjustable

Material
Bench frame Steel profile 70/25/3 mm
Worktop Depending on requirement
Height-adjustable feet Plastic housing with steel spindle

29
3 SCALA XPRESS
Bench with cantilever frame

Intended use
Laboratory benches and sinks

„„Bench frame with worktop made of various materials as a work surface and storage area for laboratory
work
„„Supporting construction for analytical equipment and superstructures

„„For fixing to the wall or for fixing to a service spine

Design

Technical data
Dimensions
Width [mm] 600 900 1200 1500 1800
Depth [mm] 750
900
Working height [mm] 750
900

Load bearing capacity

Cantilever frame [kg] 200 (for permanent mounting to a wall or a wall-mounted service spine)

Design characteristics
Construction For suspended and movable underbench units, can be moved for all kinds of frames
Height-adjustable feet Individually adjustable

Material
Bench frame Steel profile 70/25/3 mm
Worktop Depending on requirement
Height-adjustable feet Plastic housing with steel spindle

30
 SCALA XPRESS
Mobile table
3
Intended use

Laboratory benches and sinks

„„Movable bench frame with worktop made of various materials as a work surface and storage area for
laboratory work
„„Movable supporting construction for analytical equipment and superstructures

Design

Technical data
Dimensions
Width [mm] 900 1200 1500
Depth [mm] 600
750
900
Working height [mm] 750
900

Load bearing capacity

Mobile table [kg] 150
Per heavy load castor [kg] 110

Design characteristics
Heavy load castors 4, of which 2 can be locked (castor and steering axle can be locked)
Shelf Optional
Underbench unit Optional

Material
Bench frame Steel profile 60/25/2 mm
Worktop Depending on requirement

31
3 SCALA XPRESS
Height-adjustable table

Intended use
Laboratory benches and sinks

„„Bench frame with worktop made of various materials as a height-adjustable work surface and storage
area for laboratory work
„„Supporting construction for analytical equipment and superstructures

Design

Technical data
Dimensions
Width [mm] 1200 1500
Depth [mm] 750
900
Working height [mm] 700 – 950

Material
Bench frame Steel profile 60/25/2 mm
Worktop Depending on requirement
Height-adjustable feet Plastic housing with steel spindle

Load bearing capacity

Total [kg] 200

Design characteristics
Working height Can be adjusted with a grid of 25 mm
Bench frame H-frame

32
 SCALA XPRESS
Worktop material
3

Laboratory benches and sinks

Melamine resin facing
Critical substances Acids in concentrations > 10 %
Damaging substances Concentrated hydrochloric acids
Nitric acid
Heated sulphuric acid
Advantage Flat
Limitations Joints sensitive to moisture
Medium chemical resistance
Use Mobile table, add-on table, window benches
Instrument benches and laboratory benches in the dry area
Cannot be used in the moist or wet area
Weight [kg/m²] 19.6
Overall thickness [mm] 30
Light grey
NCS S 3005 R80B

Polypropylene
Critical substances Hydrocarbons
Citric acid
Oxalic acid
Carbon tetrachloride
Diesel oil
Damaging substances Ozone
Concentrated nitric acid
Chloroform
Petrol
Benzol
Advantage No joints
Flat
Light
High chemical resistance to acids and many solvents
Easy to dispose of
Less breakage of glass
Limitations Soft surface sensitive to scratches
Sensitive to heat
Use Areas with high resistance to chemicals
Working with hydrofluoric acid
Radio-isotope area
Areas in which the lack of joints is important
Weight [kg/m²] 20.3
Overall thickness [mm] 30
Raised edge [mm] 7
Light grey
NCS S 3005 R80B

33
3
Laboratory benches and sinks SCALA XPRESS
Worktop material

Solid grade laminate

Critical substances Acids in concentrations > 10 %
Damaging substances Concentrated hydrochloric acids
Nitric acid
Heated sulphuric acid
Advantage Moisture-resistant
Flat
Easy to dispose of
Limitations Reduced coating thickness
Use Wet rooms
Physical laboratories
Tables with average load
Weight [kg/m²] 26.4
Overall thickness [mm] 19
Raised edge (as an option) [mm] 7
Light grey
NCS S 3005 R80B

Solid grade laminate, EBC surface

Critical substances Acids in concentrations > 10 %
Damaging substances Concentrated hydrochloric acids
Nitric acid
Heated sulphuric acid
Advantage Antibacterial
Electron steel hardened surface (Electron Beam Curing EBC)
High chemical resistance
Moisture-resistant
Flat
Easy to dispose of
Limitations Reduced coating thickness
Use Chemical, microbiological, genetical-engineering laboratories
Weight [kg/m²] 26.4
Overall thickness [mm] 20
Raised edge (as an option) [mm] 7
Grey
Similar to NCS S 3000 N

34
 SCALA XPRESS
Worktop material
3

Laboratory benches and sinks

Epoxy
Critical substances Various solvents
Diluted acids
Damaging substances Hydrofluoric acid
Concentrated warm mineral acids
Advantage No joints
Flat
Solid panel
High mechanical load capacity
Easy to dispose of
Limitations Surface sensitive to scratches
Sensitive to concentrated acids
Use Laboratory workstation of all type
Weight [kg/m²] 32
Overall thickness [mm] 19
Raised edge [mm] 7
Platinum grey
Similar to NCS S 4202-R

Glass
Critical substances None
Damaging substances Hydrofluoric acid
Advantage Flat
High chemical resistance
Limitations Sensitive to knocks at corners and edges
Use Laboratory benches of all types subject to large amounts of chemicals
Weight [kg/m²] 38
Overall thickness [mm] 30
Light green
NCS S 2010 G10Y

! Epoxy and glass worktops are only available with the 10-week
programme!

! Glass worktops are only available in a grid of 1,200 /1,500 /1,800 mm and
without cut-outs!

35
3
Laboratory benches and sinks SCALA XPRESS
Worktop material

Stoneware
Critical substances None
Damaging substances Hydrofluoric acid
Advantage Best chemical resistance
Mechanically stable
Easy to dispose of
Limitations Evenness tolerances due to firing process
Thermodynamic stress limited
Use Areas subject to very high chemical and mechanical stress
Weight [kg/m²] 56
Overall thickness [mm] 26
Raised edge [mm] 7
Light grey
NCS S 3005 R80B

! No cut-outs can be made in stoneware worktops!

Composite worktop
Critical substances None
Damaging substances Hydrofluoric acid
Advantage Flat
Lighter than stoneware
Best chemical resistance
Easy to dispose of
Limitations Thermodynamic stress limited
Use Areas with very high chemical stress
Weight [kg/m²] 40
Overall thickness [mm] 30
Raised edge [mm] 7
White
Similar to NCS S 0300-N

! P
 lease consider available dimensions for Stoneware and composite
w/ raised edge!

36
 SCALA XPRESS
Worktop material
3

Laboratory benches and sinks

4-sided raised edge Application Depth [mm] Width 1200 Width 1500 Width 1800
On all 4 sides [mm] [mm] [mm]
Bench w/o spine 750 748   
Bench w/o spine 900 898   
Bench w. spine 750 672   


Bench w. spine 900 822   
/
/




Double bench w. spine 1500 702   

Double bench w. spine 1800 852   

 Machine-cut edge  available

 Glazed edge  not available

3-sided raised edge Application Depth [mm] Width 898 Width 1198 Width 1498 Width 1798
On front, left and back [mm] [mm] [mm] [mm]
Bench w/o spine 750 745    


Bench w/o spine 900 895    

Bench w. spine 750 672    


 Bench w. spine 900 822    
Double bench w. spine 1500 702    
Double bench w. spine 1800 852    


 Machine-cut edge  available

 Glazed edge  not available

2-sided raised edge Application Depth [mm] Width 895 Width 1195 Width 1495 Width 1795
On front and back [mm] [mm] [mm] [mm]
Bench w/o spine 750 745    


Bench w/o spine 900 895    

Bench w. spine 750 672    


Bench w. spine 900 822    
Double bench w. spine 1500 702    
Double bench w. spine 1800 852    


 Machine-cut edge  available

 Glazed edge  not available

3-sided raised edge Application Depth [mm] Width 898 Width 1198 Width 1498 Width 1798
On front, right and back [mm] [mm] [mm] [mm]
Bench w/o spine 750 745    


Bench w/o spine 900 895    

Bench w. spine 750 672    


Bench w. spine 900 822    
Double bench w. spine 1500 702    
Double bench w. spine 1800 852    


 Machine-cut edge  available

 Glazed edge  not available

! No cut-outs can be made in stoneware worktops!

37
3 SCALA XPRESS
Laboratory sink

Intended use
Laboratory benches and sinks

„„Water supply and disposal

„„For cleaning operating equipment
3
„„To take up large amounts of water

„„Not suitable for the disposal of chemicals 2

Design
1

1 Underbench unit
2 Sink
3 Outlet

Technical data
Material Material Sink dimensions Type of installation
Worktop Sinks Width x depth x height [mm]
Melamine resin facing, Polypropylene 380 x 380 x 250 Sink with surrounding raised edge installed in the
Solid grade laminate, 530 x 380 x 250 worktop from above
Solid grade laminate EBC 680 x 380 x 250
surface, Polypropylene

Dimensions
Width [mm] 600 900 1200 1500 1800
Depth [mm] 6001)
6751)
7051)
750
825
855
900
Working height [mm] 900
1)
Positioning of the outlets on the side of the sink, if required

! For worktop material please refer to category „worktops“

(Stoneware worktops are excluded on account of cut-outs!)

! Available sink material: - Polypropylene

38
 SCALA XPRESS
Drip cup on service spine
3
Intended use

Laboratory benches and sinks

„„Water supply and disposal
„„For cleaning operating equipment
„„Sink module underneath water fittings to take up small amounts of water

„„Not suitable for the disposal of chemicals

Design

1 Service panel with corner valves

2 Sink module
3 Fascia panel for service spine

Technical data
Dimensions Polypropylene
Width [mm] 294
Depth [mm] 132
Height [mm] 112
Internal sink dimensions width x depth x Approx. 280 x 93 x 93
height [mm]

Material
Sink module Polypropylene

Design characteristics
Construction Attached to the fascia panel of the service spine

Sanitary technology
Water connection Permanent connection
Waste water connection Permanent connection with siphon
Water fitting (tap) Cell outlets as an option

39
3 SCALA XPRESS
Balance table

Intended use
Laboratory benches and sinks

„„For setting up analytical balances and other sensitive measuring equipment

„„Bench frame with worktop and specially mounted, vibration-free plate

Design

1 Balance plate made of fine

concrete
2 Table cover

Technical data
Dimensions
Width [mm] 900
Depth [mm] 750
900
Working height [mm] 750
900
Width x depth [mm] balance plate 400 x 450

Material
Supporting construction Steel profile
Worktop Melamine
Solid grade laminate
Solid grade laminate, EBC surface
Balance plate Fine concrete

Weight
Total weight [kg] 120
Balance plate [kg] 65

Design characteristics
Construction Specially mounted, heavy balance plate made of fine concrete
Supporting construction with balance plate, vibration-decoupled

40
41
Laboratory benches and sinks
3
4 SCALA XPRESS
Underbench unit on plinth

! P
 ossible storage cupboard material in XPRESS: Standard melamine!
Storage cupboards

Intended use
„„Forstoring equipment and chemicals in acc. with EN 14727
„„Forworking heights of 750 mm and 900 mm
„„Not suitable for storing flammable liquids, gas cylinders and self-igniting or self-decomposing substances

„„Not suitable for storing acids and alkalis

Variants

42
 SCALA XPRESS
Underbench unit on plinth
4
Technical data

Storage cupboards
Dimensions
Width [mm] 450 600 900 1200
Depth [mm] 550
Overall height [mm] 720
870
Height, drawers [mm] 150
200
400
Combination possibilities see variants
Height, plinth [mm] 110

Load bearing capacity

Per shelf/drawer [kg] 30

Design characteristics
Construction For working height 750 and 900 mm
Hinged doors with 270° hinges
Drawers, fully extensible
Open at the top, rear panel can be removed
Shelf, height-adjustable
4 height-adjustable feet
Combination possibilities See variants
Handle Handle bar SCALA
U handle, stainless steel
Full-height drawers Optional
Soft stop for drawer Standard
Extract air spigot Optional
Closing Optional

43
4 SCALA XPRESS
Underbench unit on castors

Intended use
Storage cupboards

„„Forstoring equipment and chemicals flexibly in acc. with EN 14727

„„Forworking heights of 750 mm and 900 mm
„„Not suitable for storing flammable liquids, gas cylinders and self-igniting or self-decomposing substances

„„Not suitable for storing acids and alkalis

Variants

44
 SCALA XPRESS
Underbench unit on castors
4
Technical data

Storage cupboards
Dimensions
Width [mm] 450 545 600 845 900 1145 1200
Depth [mm] 550
Overall height [mm] 640
790
Height, drawers [mm] 150
200
350
Combination possibilities see variants
Height, castors [mm] 110

Load bearing capacity

Per shelf/drawer [kg] 30
Per castor [kg] 70

Design characteristics
Construction For working height 750 and 900 mm
Hinged doors with 270° hinges
Drawers, fully extensible and with change-pull-out catch
Shelf, height-adjustable
Covered at the top, rear panel permanently connected with the carcass
4 swivelling castors, front castors can be locked
Combination possibilities See variants
Handle Handle bar SCALA
U handle, stainless steel
Soft stop for drawer Standard
Closing Optional
Drawers with change-pull-out catch Standard

45
4 SCALA XPRESS
Suspended underbench unit

Intended use
Storage cupboards

„„Forstoring equipment and chemicals flexibly in acc. with EN 14727

„„Forworking heights of 750 mm and 900 mm
„„Not suitable for storing flammable liquids, gas cylinders and self-igniting or self-decomposing substances

„„Not suitable for storing acids and alkalis

Variants

46
 SCALA XPRESS
Suspended underbench unit
4
Technical data

Storage cupboards
Dimensions
Width [mm] 450 545 600 845 900 1145 1200
Depth [mm] 500 (depth of frame 572)
550 (depth of frame 672)
Height [mm] 380
530
Height, drawers [mm] 150
200
350
Combination possibilities see variants

Load bearing capacity

Per shelf/drawer [kg] 30

Design characteristics
Construction For working height 750 and 900 mm
2 fittings for attaching to the profile rail of the bench frame
Hinged doors with 270° hinges
Drawers, fully extensible
Covered at the top, rear panel permanently connected with the carcass
Shelf, height-adjustable
For C-frame/cantilever bench frame: Can be moved to the sides until it protrudes over
the bench grid
Hinged doors with 1 shelf at a height of 530 mm
Combination possibilities See variants
Handle Handle bar SCALA
U handle, stainless steel
Soft stop for drawer Standard
Closing Optional

47
4 SCALA XPRESS
Push-in underbench unit for fume hoods

Intended use
Storage cupboards

„„For storing equipment and chemicals in acc. with EN 14727

„„For fume hoods with rear panel installation and for fume hoods with side installation on a steel support
frame
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or self-decomposing

substances
„„Not permitted for storing acids and alkalis

Variants

48
 SCALA XPRESS
Push-in underbench unit for fume hoods
4
Technical data

Storage cupboards
Dimensions
Width [mm] 545 600 845 900 1145 1200
Depth [mm] 550
Overall height [mm], push-in underbench unit 640
for bench-mounted fume hoods with rear
panel installation
Overall height [mm], push-in underbench unit 716
for bench-mounted fume hoods with side
installation
Height, plinth [mm] 110
Height, drawers [mm] 150
220
Combination possibilities see variants

Load bearing capacity

Per shelf [kg] 30

Design characteristics
Construction Hinged doors with 270° hinges
Drawers, fully extensible
Closed at the top, rear panel can be removed
Shelf, height-adjustable
4 height-adjustable feet
Combination possibilities See variants
Handle Handle bar SCALA
U handle, stainless steel
Extract air spigot Optional
Closing Optional

49
4 SCALA XPRESS
Underbench unit for sinks

Intended use
Storage cupboards

„„Asan underbench unit for sinks for storing equipment and chemicals in acc. with EN 14727
„„Not suitable for storing flammable liquids, gas cylinders and self-igniting or self-decomposing substances
„„Not suitable for storing acids and alkalis

Design
Sink with underbench unit for service spines or wall benches

End sink for double benches

50
 SCALA XPRESS
Underbench unit for sinks
4
Variants

Storage cupboards
Sink with underbench unit for service spines or wall benches

End sink for double benches

51
4 SCALA XPRESS
Underbench unit for sinks

Technical data
Storage cupboards

Dimensions
Width [mm] 600 1) 900 1) 1200 1) 1420 2) 1720 2)
Depth [mm] 550 700
Overall height [mm] 870
Height, plinth [mm] 110
1)
For sinks on service spines or wall benches
2)
For end sinks

Load bearing capacity

Per shelf/drawer [kg] 30

Design characteristics
Construction Hinged doors with 270° hinges
4 height-adjustable feet
Inclined swivel door with waste bin 30 l
Waste bin 2 x 15 l with full-height drawer
Waste bin 2 x 35 l with full-height drawer
Hinged door(s), full-height drawer
Combination possibilities see variants
Handle Handle bar SCALA
U handle, stainless steel
Closing Optional

52
 SCALA XPRESS
Overbench cabinet
4
Intended use

Storage cupboards
„„Forstoring equipment and chemicals in acc. with EN 14727
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or self-decomposing
substances
„„Not permitted for storing acids and alkalis

Design

Variants

53
4
Storage cupboards SCALA XPRESS
Overbench cabinet

Technical data
Dimensions
Width [mm] 450 600 900 1200
Depth [mm] 350
Height [mm] 460
760

Load bearing capacity

Per shelf [kg] 30
Load bearing capacity, total [kg] 60

Design characteristics
Construction Height-adjustable fitting for fastening to the wall or to the service spine
For a width of 1200 mm with central panel
Shelf, height-adjustable
Combination possibilities See variants
Handle U handle SCALA
U handle, stainless steel
Glass sliding door with affixed plastic handle
Closing Optional

54
 SCALA XPRESS
Laboratory cabinet
4
Intended use

Storage cupboards
„„Forstoring equipment and chemicals in acc. with EN 14727
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or self-decomposing
substances
„„Not permitted for storing acids and alkalis

Design

55
4 SCALA XPRESS
Laboratory cabinet

Variants
Storage cupboards

56
 SCALA XPRESS
Laboratory cabinet
4

Storage cupboards

57
4 SCALA XPRESS
Laboratory cabinet

Technical data
Storage cupboards

Dimensions
Width [mm] 450 600 900 1200
Depth [mm] 350
550
Overall height [mm] 2090
Height, plinth [mm] 110

Load bearing capacity

Per shelf [kg] 30

Design characteristics
Construction Hinged doors with 270° hinges
Shelves, height-adjustable
Drawers, fully extensible
4 height-adjustable feet
Combination possibilities See variants
Drawers only with a depth of 550 mm
Handle U handle SCALA
U handle, stainless steel
Shelves, extendable Optional (with a cabinet depth of 550 mm)
Drawers Optional (with a cabinet depth of 550 mm)
Soft stop for drawer Standard
Extract air spigot Optional
Closing Optional

58
 SCALA XPRESS
Emergency cabinet
4
Intended use

Storage cupboards
„„Forstoring protection and rescue materials (fire extinguisher, first aid case, etc.)
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or self-decomposing
substances
„„Not permitted for storing acids and alkalis

Design

Technical data
Dimensions
Width [mm] 600
Depth [mm] 350
550
Overall height [mm] 2090
Height, plinth [mm] 110

Design characteristics
Construction Hinged door with 270° hinges
4 shelves, height-adjustable
4 height-adjustable feet
Equipment First aid case
Fire extinguisher, 5 kg
Sand boxes
Shovel
Fire blankets

59
4 SCALA XPRESS
Top-mounted cabinet

Intended use
Storage cupboards

„„For storing equipment and chemicals in acc. with EN 14727

„„Only suitable as a permanently installed top part on the following Waldner cabinets: Laboratory cabinet,
pull-out cabinet, emergency cabinet and acids and alkalis cabinet
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or self-decomposing

substances
„„Not permitted for storing acids and alkalis

Design

Technical data
Dimensions
Width [mm] 450 600 900 1200
Depth [mm] 350
550
Height [mm] 610
760

Load bearing capacity

Per shelf [kg] 30

Design characteristics
Construction With rail for securing a ladder
For laboratory cabinets with or without extract air spigot
1 shelf, height-adjustable
Hinged doors
Handle U handle SCALA
U handle, stainless steel
Hook ladder Optional
Closing Optional

60
 SCALA XPRESS
Pull-out cabinet
4
Intended use

Storage cupboards
„„Forstoring liquid or solid substances in suitable containers in acc. with EN 14727
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or self-decomposing
substances
„„Not permitted for storing acids and alkalis

Design

1 Wire basket with tray

2 Pull-out

61
4 SCALA XPRESS
Pull-out cabinet

Technical data
Storage cupboards

Dimensions
Width [mm] 600 900
Depth [mm] 550
Overall height [mm] 2090
Height, plinth [mm] 110
Tray, width x depth x height [mm] 240 x 425 x 40

Load bearing capacity

Per drawer [kg] 120
Per tray [kg] 10

Design characteristics
Construction 5 wire baskets with trays for each drawer, height-adjustable
Fastened to the wall
4 height-adjustable feet
Drawer doors with drawers accessible from both sides
Handle U handle SCALA
U handle, stainless steel
Soft stop for drawers Optional
Compartment partitioning Optional
Extract air spigot Optional
Closing Optional

Material
Tray Polyethylene

62
 SCALA XPRESS
Laboratory cabinet for storing acids and alkalis
4
Intended use

Storage cupboards
„„For storing limited amounts of flammable acids and alkalis
„„Not suitable for storing flammable liquids, gas cylinders and self-igniting or self-decomposing substances

Design

63
4 SCALA XPRESS
Laboratory cabinet for storing acids and alkalis

Technical data
Storage cupboards

Dimensions
Width [mm] 600
Depth [mm] 550
Overall height [mm] 2090
Height, plinth [mm] 110

Load bearing capacity

Per shelf, height-adjustable [kg] 30
Per pull-out shelf [kg] 20

Design characteristics
Construction Connection to the permanently active ventilation system
4 shelves, fixed or pull-out
4 height-adjustable feet
Separate compartments for acids and alkalis
Trays made of polypropylene
Coated fittings
Hinged doors
Handle U handle SCALA
U handle, stainless steel

Ventilation data
Air exchange rate [m³/h] 100
Ventilation connection Ø [mm] 90
Connection height extract air spigot [mm] 2176

64
 SCALA XPRESS
Underbench safety unit for fume hoods for storing
4
acids and alkalis
Intended use

Storage cupboards
„„Push-in or self-supporting underbench unit for bench-mounted fume hoods for storing limited amounts of
acids and alkalis
„„Not suitable for storing flammable liquids, gas cylinders and self-igniting or self-decomposing substances

Design

Variants
Push-in underbench units

Self-supporting underbench units for fume hoods

with rear panel installation

Self-supporting underbench units for fume hoods

with side installation

65
4 SCALA XPRESS
Underbench safety unit for fume hoods for storing
acids and alkalis
Technical data
Storage cupboards

Dimensions
Width [mm] 600 900
Depth [mm] 550
Width for push-in underbench units [mm] 545/600/845/900
Overall height [mm], push-in underbench units 640
for bench-mounted fume hoods with rear
panel installation
Overall height [mm], push-in underbench units 716
for bench-mounted fume hoods with side
installation
Overall height [mm], self-supporting 820
underbench units for bench-mounted fume
hoods with rear panel/side installation
Height, plinth [mm] 110

Load bearing capacity

Extendable shelf [kg] 20

Design characteristics
Construction Connection to the permanently active ventilation system
4 height-adjustable feet
Coated fittings
2 extendable shelves with trays
Hinged doors
Combination possibilities see variants
Handle Handle bar SCALA
U handle, stainless steel

Ventilation data
Air exchange rate [m³/h] 30
Ventilation connection to the ascending duct 90
Ø [mm]

66
 SCALA XPRESS
FWF 90 underbench safety unit for fume hoods
4
for storing flammable liquids
Intended use

Storage cupboards
„„Push-in underbench unit for bench-mounted fume hoods for storing limited amounts of flammable liquids
„„Not suitable for storing gas cylinders and self-igniting or self-decomposing substances
„„Not suitable for storing acids and alkalis

Design

Variants

1
Version
Zeichnung genehmigt von : Genehmigungsdatum :
(Vollständiger Name in Großbuchstaben)

Alle Dokumente sind urheberrechtlich geschützt. Kein Teil dieser Dokumente d

in irgendeiner Form oder auf irgendeine Weise, elektronisch oder mechanisch,
Erstellt durch (TT/M
WeissS 22.0
Geschoss, Raum

-
Projekt

Düperthal UB und Abzug

Projektnummer / Bestellnummer
WALDNER Laboreinrichtungen GmbH & Co. KG
Haidösch 1 88239 Wangen Germany
+49 7522 986 480 / +49 7522 986 418
www. waldner-lab.com [email protected]

Status:

67
4 SCALA XPRESS
FWF 90 underbench safety unit for fume hoods for
storing flammable liquids
Technical data
Storage cupboards

Dimensions
Width [mm] 600 890 1100 1400
Depth [mm] 600
Overall height [mm] 635
Height, plinth [mm] 35
Max. weight [kg] 130 170 220 290

Load bearing capacity

Rigid shelf [kg] 30
Drawers [kg] 25

Design characteristics
Construction Connection to the permanently active ventilation system
Connection to the earth wire with potential equalisation
With closing
Tray with perforated plate insert
Self-closing through current-independent thermal activation in the case of fire
Hinged doors
Drawer
Combination possibilities See variants
Handle U handle, stainless steel
Additional tray pull-out Optional for drawers
Regulations and standards EN 14470-1
TRGS 510

Ventilation data
Air exchange rate [m³/h] 30
Ventilation connection to the ascending duct 90
Ø[mm]

Material
Underbench unit Powder-coated stainless steel on the outside
Colour: Pure white RAL 9010
Ventilation connection PPS

68
 SCALA XPRESS
Waste disposal system for solid matter and
4
domestic waste
Intended use

Storage cupboards
„„For the disposal of remnants of solid matter and garbage from laboratory work
„„Not suitable for the permanent storage of solid matter and garbage
„„Not permitted for the disposal of hazardous substances, especially:

XXAcids and alkalis

XXFlammable liquids

XXGas cylinders

XXRadioactive substances

XXMicroorganisms

Design

Waste bin with full-height drawer

2
1 Full-height drawer 1
2 Waste bin 2 x 15 l
3 Waste bin 2 x 35 l

Waste bin with tilting door

1 Tilting door 2
2 Waste bin 30 l
3 Waste bin 2 x 35 l 1

69
4 SCALA XPRESS
Waste disposal system for solid matter and domestic
waste
Technical data
Storage cupboards

Dimensions for underbench unit on plinth

Width x height [mm] 450 x 870 600 x 870 450 x 720 600 x 720
Depth [mm] 550
Height, plinth [mm] 110
Capacity with full-height drawer 2 x 15 l or 2 x 15 l 2 x 15 l or 2 x 15 l
2 x 35 l – 2 x 35 l –
Capacity with tilting door 1 x 30 l

Dimensions for underbench unit for sinks

Width x height [mm] 600 x 870 900 x 870 1200 x 870
Depth [mm] 550
Height, plinth [mm] 110
Capacity with full-height drawer – 2 x 15 l
Capacity with tilting door 1 x 30 l 2 x 30 l

Dimensions for self-supporting underbench unit for bench-mounted fume hoods

Width x height [mm] 600 x 820
Depth [mm] 550
Height, plinth [mm] 110
Capacity with full-height drawer 2 x 15 l
Capacity with tilting door 1 x 30 l

Dimensions for push-in underbench unit for bench-mounted fume hoods

Width x height [mm] 545 x 639 600 x 639
Depth [mm] 550
Height, plinth [mm] 110
Capacity with full-height drawer 2 x 15 l
Capacity with tilting door 1 x 30 l

Design characteristics
Door Full-height drawer
Tilting door
Automatic foot-operated opening Optionally for full-height drawers up to a width of 600 mm
Extract air spigot Optional

Material
Ventilation connection PPS

Ventilation data
Air exchange rate [m³/h] 30
Ventilation connection to the ascending duct 90
Ø[mm]

70
 SCALA XPRESS
FWF 90 safety cabinet for storing flammable liquids
4
Intended use

Storage cupboards
„„Forstoring limited amounts of flammable liquids
„„Not suitable for storing gas cylinders and self-igniting or self-decomposing substances
„„Not suitable for storing acids and alkalis

Design

Variants

71
4 SCALA XPRESS
FWF 90 safety cabinet for storing flammable liquids

Technical data
Storage cupboards

Dimensions
Width [mm] 600 900 1200
Depth [mm] Approx. 600
Overall height [mm] Approx. 2000
Height, plinth [mm] Approx. 80
Max. weight [kg] 290 360 470

Load bearing capacity

Basin bed [kg] Depending on version

Design characteristics
Construction Connection to the permanently active ventilation system
Connection to the earth wire with potential equalisation
Self-closing through current-independent thermal activation in the case of fire
3 basin beds, height-adjustable
Tray with perforated plate insert
With closing
4 height-adjustable feet
Hinged doors
Combination possibilities See variants
Other versions and configurations On request
Regulations and standards EN 14470-1
TRGS 510

Ventilation data
Air exchange rate [m³/h] 30
Ventilation connection Ø [mm] 75

Material
Laboratory cabinet Powder-coated stainless steel on the outside
Colour: Pure white RAL 9010
Ventilation connection Galvanised steel

72
 SCALA XPRESS
G 90 gas cylinder cabinet
4
Intended use

Storage cupboards
„„Forstoring gas cylinders in buildings
„„Not suitable for storing flammable liquids and self-igniting or self-decomposing substances
„„Not suitable for storing acids and alkalis

Design

Variants

73
4 SCALA XPRESS
G 90 gas cylinder cabinet

Technical data
Storage cupboards

Dimensions 600 900 1200 1400

Width [mm] 600 900 1200 1400
Depth [mm] Approx. 600
Overall height [mm] Approx. 2000
Max. net weight [kg] 390 530 660 740

Design characteristics 600 900 1200 1400

Construction Connection to the permanently active ventilation system
Mounting rail to take up gas reduction units
Roll-in ramp for gas cylinders
With closing
4 height-adjustable feet
Feed-throughs for pipes and cables in the cabinet ceiling
Hinged door(s)
Max. number of 50 l gas cylinders for cabinet 1 3 4 4
width
Other versions and configurations On request
Regulations and standards EN 14470-2

Ventilation data 600 900 1200 1400

Air exchange rate [m³/h] for cabinet width 60 90 120 140
Ventilation connection Ø [mm] 75

Material
Laboratory cabinet Powder-coated stainless steel on the outside
Colour: Pure white RAL 9010
Ventilation connection Galvanised steel

74
75
Storage cupboards
4
5 SCALA XPRESS
Services

Mechanical Services
Services

Service Abbreviation System (Material) Dimension of pipe Execution of branch pipe

Synthetic gases < 2.0 (non combustible)
Compressed air CA PEX 15 x 2.5 mm Uniflex-V (SPX)
22 x 3,0 mm
Low vacuum (1 - 1000 mbarabs) V PEX 10 x 1.25 mm Uniflex-V (SPX)
Nitrogen (up to 2.0) N2 Cu - PressW 15 x 1.0 mm Uniflex-V (SPX)
Argon (up to 2.0) Ar Cu - PressW 15 x 1.0 mm Uniflex-V (SPX)
Carbon dioxide (up to 2.0) CO2 Cu - PressW 15 x 1.0 mm Uniflex-V (SPX)
Helium (up to 2.0) He Cu - PressG 15 x 1.0 mm Uniflex-Y (VA-corrugated
hose)
Synthetic gases < 2.0 (combustible) + allgases (G260)
Natural gas (< 0.1 bar) G Cu - PressG 15 x 1.0 mm Uniflex-Y (VA-corrugated
22 x 1.0 mm hose)
Liquefied gas (< 0.1 bar) LPG Cu - PressG 15 x 1.0 mm Uniflex-Y (VA-corrugated
22 x 1.0 mm hose)
Ultra-high purity gases
Nitrogen (up to 5.5) N2 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Argon (up to 5.5) Ar Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Helium (up to 5.5) He Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Oxygen (up to 5.5) O2 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Carbon dioxide (up to 5.5) CO2 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Hydrogen (up to 5.5) H2 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Carbogene (up to 5.5) O2 / CO2 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Synthetic air (up to 5.5) SA Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Carbon monoxide (up to 5.5) CO Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Forming gas (up to 5.5) H2 / N2 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Nitrous oxide (up to 5.5) N2O Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Acetylene (up to 4.0) C2H2 VA - free of grease 6 x 1.0 mm 6 x 1.0 VA
10 x 1.0 mm
Selective gas (up to 5.5) W1 Cu - free of grease 10 x 1.0 mm 6 x 1.0 Cu - free of grease
Waters
Cold water WPC / WNC Cu - PressW 15 x 1.0 mm Uniflex-V (SPX)
VA - PressW (as an 22 x 1.0 mm
option)
Hot water WPH / WNH Cu - PressW 15 x 1.0 mm (isol.) Uniflex-V (SPX)
VA - PressW (as an 22 x 1.0 mm (isol.)
option)
Desalinated water WDC PEX 15 x 1.0 mm PAw 10 x 1mm /
PP (as an option) 22 x 1.0 mm PTFE 10 x 1mm
Cooling water supply/return WCF / WCR Cu - PressW 15 x 1.0 mm (isol.) Uniflex-V (SPX) isol.
(closed) 22 x 1.0 mm (isol.)
Other services
Extract air HT pipe (PP) 50 mm PVC
Waste water Ab PE-HD (DN56) 56 x 3.0 mm PP / PE-HD

76
 SCALA XPRESS
Services
5
Electrical services

Services
country frequence / IP-Protection socket type comment
voltage
Mexico, 60Hz / IP20/44 Type B fuse protection
Venezuela & 127/220V (NEMA 5-15R) by others
Japan 127 V

USA 60Hz / IP20/44 Type B wiring and fuse

120/208V (NEMA 5-15R) protection by
120 V others

Italy 50Hz / IP55 Type C + fuse protection

230/400V Type F + by others
Type L

Spain 50Hz / IP20/44 Type F 2-pole fuse

230/400V (Schuko) protection only,
no AC/DC
sensitive fuse
protections
available
Netherland 50Hz / IP20/44 Type F 1+N-fuse
230/400V (Schuko) protection only,
no wiring
available,
no AC/DC
sensitive fuse
protections
available
England 50Hz / 230V IP20 Type G only single phase

France & 50Hz / IP20/44 Type E

Belgium 230/400V

Switzerland 50Hz / IP20/55 Type J

230/400V

Germany 50Hz / IP20/44 Type F

230/400V (Schuko)

! I nfo: Please consider the individual comments regarding wiring

and fuse protection for your region/country!
All wirings are available as standard or halogen free

77
6 SCALA XPRESS
Laboratory Accessories

Pegboard
Accessories

Intended use
„„Frame for drying laboratory glasses
„„For fixing above sinks on service module uprights or for wall mounting

Technical data
Dimensions
Pegboard width x height [mm] 600 x 360
18 Draining pegs
Draining peg [mm] Ø 12

Design characteristics
Construction Cover panel with pegboard and removable drainage
sink

Ordering information
Version Sales Order no.
unit
Pegboard, 18 draining pegs, diameter 12 mm 1 set 81005862-22

Scope of delivery
1 core, 2 pegboards with 18 draining pegs, diameter 12 mm, 2 basins for drips

Version Sales Order no.

unit
Draining peg Ø 12 1 81006177
Draining peg Ø 9 1 81011766

Pegboard for service duct

Intended use
„„Frame for drying laboratory glasses

Technical data
Dimensions
Pegboard 300 x 260
Width x height [mm]
Draining peg [mm] Ø 12
Ø 9

Ordering information
Version Sales Order no.
unit
Pegboard for service duct, 11 draining pegs, diameter 12 mm 1 set 81005861-2

Scope of delivery
1 pegboard with 11 draining pegs, diameter 12 mm, 1 basin for drips, 1 fastening

Version Sales Order no.

unit
Draining peg Ø 12 1 81006177
Draining peg Ø 9 1 81011766
78
 SCALA XPRESS
Laboratory Accessories
6
System step ladder

Accessories
Intended use
„„For attaching to top-mounted cabinets

Technical data
Dimensions
Width [mm] 405
Height [mm] 2330

Load-bearing capacity
Capacity [kg] 150

Ordering information
Material Sales Order no.
unit
Aluminium 1 81006175

Step ladder
Technical data
Dimensions
Width x depth x length [mm] 422 x 70 x 2330

Load-bearing capacity
Capacity [kg] 150

Design characteristics
Construction With 4 steps

Ordering information
Material Sales Order no.
unit
Aluminium 1 81006174

79
6 SCALA XPRESS
Laboratory Accessories

Towel dispenser, plastic

Accessories

Intended use
„„For use as a combined paper towel dispenser for paper towels (width 240 mm,
DU 155 mm) or paper towels with C- or Z-fold, 250 x 230 mm format, to fit
Tork, Satino, Quicky and Van Houtum towels

Technical data
Dimensions
Width x depth x height [mm] 195 x 251 x 300

Ordering information
Material Order no.
Plastic 81006405
Scope of delivery
1 towel dispenser with key without paper towels

Towel dispenser, aluminium

Intended use
„„Forpaper towels with C- or Z-fold, 250 x 230 mm format, to fit Tork, Satino,
Quicky and Van Houtum towels

Technical data
Dimensions
Width x depth x height [mm] 130 x 185 x 275

Ordering information
Material Order no.
Aluminium 81006406
Scope of delivery
1 towel dispenser with key without paper towels

Soap dispenser
Intended use
„„For liquid soap with refillable 1100 ml container without cartridges, suitable
for use with Clivia liquid soap

Technical data
Dimensions
Width x depth x height [mm] 130 x 115 x 220

Ordering information
Material Order no.
Plastic 81006407
Scope of delivery
1 soap dispenser, closable without soap

80
 SCALA XPRESS
Laboratory Accessories
6
Boxes for small parts

Accessories
Intended use
„„For storing small parts

Technical data
The colours of the boxes for small parts are subject to technical changes.

Dimensions
Boxes for small parts with mounting rail 516 x 203 x 80
Width x depth x height [mm]
Small boxes 100 x 160 x 75
Width x depth x height [mm]

Load-bearing capacity
Capacity [kg] 5

Ordering information
Material Order no.
Plastic/aluminium 81005871-2

Scope of delivery
2 clamping adapters for service duct
1 mounting rail with bracket
5 boxes for small parts

Paper towel dispenser

Intended use
„„For holding paper towels

Technical data
Dimensions
Width x depth x height [mm] 270 x 146 x 88

Ordering information
Material Order no.
Steel 81005867-2

Scope of delivery
2 clamping adapters for service duct
1 paper towel dispenser

81
6 SCALA XPRESS
Laboratory Accessories

Monitor arm
Accessories

Intended use
„„For flat screens with VGSA holder 75 x 75 mm / 100 x 100 mm
„„For service spines with service duct and fascia panel

Technical data
Dimensions
Width x depth x height [mm] 280 x 390 x 283

Load-bearing capacity
Capacity [kg] 10

Design characteristics
Construction Vertically pivotable (45°)
Horizontally rotatable and movable

Ordering information
Material Order no.
Steel 81010387-2

Scope of delivery
2 clamping adapters for service duct
1 monitor cantilever

Name tag
Intended use
„„For labelling doors and drawers

Technical data
Dimensions
Width x depth x height [mm] 78 x 3 x 18

Design characteristics
Construction 3-piece, self-adhesive, with removable paper strip
for labelling

Ordering information
Material Sales Order no.
unit
Plastic transparent 1 81008260

82
 SCALA XPRESS
Laboratory Accessories
6
Pipette holder with insertion holes

Accessories
Intended use
„„To accommodate 11 pipettes

Technical data
Dimensions
Width x depth x height [mm] 297 x 175 x 66
Insertion openings [mm] 5 x Ø 26
6 x Ø 20

Ordering information
Material Order no.
Steel/plastic (PE) 81005866-2

Scope of delivery
2 clamping adapters for service duct
1 screw-on frame for pipette holder
1 plate for pipettes

Pipette holders with mounting rail

Intended use
„„To accommodate pipettes with suspension hooks

Technical data
Dimensions
Width x depth x height [mm] 300 x 41 x 80
Mounting rail [mm] Ø 21

Ordering information
Material Order no.
Steel/plastic 81010132-2

Scope of delivery
2 clamping adapters for service duct
1 screw-on frame for pipette holder
1 mounting rail for pipettes

83
6 SCALA XPRESS
Laboratory Accessories

Scaffold points for fume hoods

Accessories

Intended use
„„For mounting scaffold rods in the internal workspace
„„For scaffold rods ø 13 mm

Technical data
Design characteristics
Construction 3-section bracket

Load-bearing capacity
Capacity [kg] 5

Material
Holding nut PBT
Scaffold point PBT

Ordering information
Name Sales Order no.
unit
Scaffold point 1 81005039
Clamping nut 1 81005252
Holding nut 1 81005040

Scaffold rod
Intended use
„„For fixing to scaffold points in the fume hood or on the service spine

Technical data
Dimensions
Length [mm] 120, 300, 600, 900, 1100, 1200, 1400, 1500,
1700, 2000
Diameter [mm] 13

Material
Scaffold rod Stainless steel

Ordering information
Length [mm] (use) Sales Order no.
unit
120 1 81006152
300 1 81006153
600 1 81006154
900 1 81006155
1100 (for horizontal use in the fume hood) 1 81011630
1200 1 81006156
1400 (for horizontal use in the fume hood) 1 81011631
1500 1 81006157
1700 (for horizontal use in the fume hood) 1 81011632
84
2000 (for horizontal use in the fume hood) 1 81011633
 SCALA XPRESS
Laboratory Accessories
6
Emergency cabinet

Accessories
Intended use
„„For storing protection and rescue materials (fire extinguisher, first aid case etc.)
„„Not permitted for storing flammable liquids, gas cylinders and self-igniting or
self-decomposing substances
„„Not permitted for storing acids and alkalis

Technical data
Dimensions
Width [mm] 600
Depth [mm] 350
550
Overall height [mm] 2090
Height of plinth [mm] 110

Design characteristics
Construction Hinged door with 270° hinges
4 shelves, height-adjustable
4 height-adjustable feet
Equipment First aid case
Fire extinguisher, 5 kg
Sand boxes
Shovel
Fire blankets
Handle Stainless steel D-handle (standard design)
SCALA handle (optional)

Ordering information
Version Width x depth x height [mm] Sales Order no.
unit
1 hinged door, left 600 x 350 x 2090 1 set 81002910-3B40022
600 x 550 x 2090 1 set 81002910-5B40022

1 hinged door, right 600 x 350 x 2090 1 set 81002911-3B40022

600 x 550 x 2090 1 set 81002911-5B40022

Scope of delivery
1 laboratory cabinet with hinged door
4 shelves
1 first aid case
1 fire extinguisher
2 sand boxes
1 sand shovel
2 fire blankets

85
6 SCALA XPRESS
Laboratory Accessories

Lateral pillars
Accessories

Intended use
„„For attaching to service module upright
„„For glass shelves and OSB boards, and for scaffold points

Technical data
Dimensions
Width [mm] 171
Depth [mm] 3
Height [mm] 382

Ordering information
Material Sales Order no.
unit
Steel 1 set 81002720-322

Scope of delivery
2 lateral pillars

86
 SCALA XPRESS
Laboratory Accessories
6
Rack

Accessories
Intended use
„„Mobile flexible storage area
„„Can be used with the 600 mm deep shelf as a mobile workplace for desk work
„„Not suitable for laboratory work where hazardous substances have to be

extracted
„„Not suitable for storing hazardous substances

Technical data
Dimensions
Width [mm] with shelf 900
Depth [mm] with shelf depth 450 mm 600
Height [mm] 1790
Depth of shelf [mm] 450
600

Material
Supporting construction Steel profile
Shelf 22 mm Shelf of OSB board

Load-bearing capacity
Total [kg] 150
Shelf [kg] 20

Design characteristics
Heavy load castors 4, 2 of which can be locked (castor and steering
axle can be locked)
Shelf Can be adjusted without tools at 150 mm
increments
Integrated cable cabinet Optional

Ordering information
Version Sales Order no.
unit
Rack 1 set 81005369-31022

Scope of delivery
1 supporting construction
1 shelf, depth 600 mm
3 shelves, depth 450 mm

87
6 SCALA XPRESS
Laboratory Accessories

Drawer insert type B tray set

Accessories

Intended use
„„For fully equipping drawers
„„For underbench units with a depth of 550 mm

Technical data
Design characteristics
Drawer width [mm] 450 545 600 845 900 1145 1200
Tray configuration 1 x single element with a 140 mm wide trough
1 x single element with a 90 mm wide trough
1 x double element with two troughs, each 80 mm wide
Colour White, translucent
Surface Grained

Material
Drawer insert PP plastic
Profile rail Natural aluminium

Ordering information
For drawer width 450 mm Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
2 pieces 350 x 480 x 48 1 81012701

For drawer width 545 mm Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
3 pieces 445 x 480 x 48 1 81012702

For drawer width 600 mm Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
4 pieces 500 x 480 x 48 1 81012703
3 pieces 500 x 480 x 48 1 81012704

For drawer width 845 mm

Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
5 pieces 745 x 480 x 48 1 81012705

88
 SCALA XPRESS
Laboratory Accessories
6

Accessories
For drawer width 900 mm Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
5 pieces 800 x 480 x 48 1 81012706
7 pieces 800 x 480 x 48 1 81012707
6 pieces 800 x 480 x 48 1 81012708

For drawer width 1145 mm Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
7 pieces 1045 x 480 x 48 1 81012709
8 pieces 1045 x 480 x 48 1 81012710

For drawer width 1200 mm Drawer inserts per set Width x depth x height [mm] Sales Order no.
unit
7 pieces 1100 x 480 x 48 1 81012711
8 pieces 1100 x 480 x 48 1 81012712
10 pieces 1100 x 480 x 48 1 81012713

Scope of delivery per set

1 drawer insert type A with profiled rods
2 sealing lips

Separating rod for drawer Bowl element Sales Order no.

insert type B tray set unit
80 mm 1 81012700
90 mm 1 81012698
140 mm 1 81012699

89
6
Organising systems for drawers

SCALA XPRESS
Laboratory Accessories

Drawer insert type A

Accessories

Intended use
„„For completely or partially equipping drawers
„„Variablepartitioning of drawers
„„For drawers with a depth of 450 mm and 500 mm

Technical data
Design characteristics
Equipment Nop mat, can be fixed with adhesive pads
Drawer inserts can be removed individually
Colour Light grey

Material
Drawer insert, nop mat ABS plastic

Ordering information
The dimensions of the nop mat correspond to the external dimensions of the
drawer insert type A. The nop mat and adhesive pads are included in the scope
of delivery.

For drawer depth 450 mm Drawer insert type A for Drawer inserts Sales Order no.
drawer width 450 mm Width x depth x height [mm] unit
Width x depth x height [mm]
336 x 432 x 48 2 pcs. à 96 x 288 x 48 1 set 81008343
3 pcs. à 96 x 144 x 48
3 pcs. à 96 x 96 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 545 mm Width x depth x height [mm] unit
Width x depth x height [mm]
432 x 432 x 48 3 pcs. à 96 x 240 x 48 1 set 81008344
3 pcs. à 96 x 192 x 48
3 pcs. à 144 x 144 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 600 mm Width x depth x height [mm] unit
Width x depth x height [mm]
480 x 432 x 48 5 pcs. à 96 x 240 x 48 1 set 81008345
5 pcs. à 96 x 144 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 845 mm Width x depth x height [mm] unit
Width x depth x height [mm]
720 x 432 x 48 3 pcs. à 240 x 336 x 48 1 set 81008346
3 pcs. à 96 x 240 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 900 mm Width x depth x height [mm] unit
Width x depth x height [mm]
792 x 432 x 48 8 pcs. à 96 x 144 x 48 1 set 81008347
6 pcs. à 96 x 288 x 48
3 pcs. à 96 x 192 x 48

90
 SCALA XPRESS
Laboratory Accessories
6

Accessories
Drawer insert type A for Drawer inserts Sales Order no.
For drawer depth 450 mm drawer width 1145 mm Width x depth x height [mm] unit
Width x depth x height [mm]
960 x 432 x 48 1 pc. à 240 x 336 x 48 1 set 81008348
9 pcs. à 144 x 192 x 48
3 pcs. à 144 x 144 x 48
1 pc. à 96 x 240 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 1200 mm Width x depth x height [mm] unit
Width x depth x height [mm]
1080 x 432 x 48 6 pc. à 144 x 384 x 48 1 set 81008349
3 pcs. à 96 x 288 x 48
3 pcs. à 96 x 144 x 48

Scope of delivery
1 drawer insert type A
1 nop mat (dimensions correspond to the drawer insert type A)
4 adhesive pads

For drawer depth 500 mm Drawer insert type A for Drawer inserts Sales Order no.
drawer width 450 mm Width x depth x height [mm] unit
Width x depth x height [mm]
336 x 480 x 48 1 pc. à 144 x 192 x 48 1 set 81008350
3 pcs. à 96 x 192 x 48
3 pcs. à 96 x 144 x 48
4 pcs. à 96 x 96 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 545 mm Width x depth x height [mm] unit
Width x depth x height [mm]
432 x 480 x 48 1 pc. à 96 x 336 x 48 1 set 81008351
2 pcs. à 96 x 288 x 48
6 pcs. à 96 x 144 x 48
4 pcs. à 96 x 96 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 600 mm Width x depth x height [mm] unit
Width x depth x height [mm]
480 x 480 x 48 2 pcs. à 96 x 288 x 48 1 set 81008352
2 pcs. à 96 x 240 x 48
4 pcs. à 96 x 192 x 48
4 pcs. à 96 x 144 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 600 mm Width x depth x height [mm] unit
Width x depth x height [mm]
480 x 480 x 24/48 1 pc. à 240 x 336 x 48 1 set 81006027
2 pcs. à 144 x 192 x 48
1 pc. à 144 x 144 x 48
1 pc. à 144 x 192 x 24 (drawer
insert with 8 partitions)
1 pc. à 96 x 192 x 24 (drawer
insert with 3 partitions)
2 pcs. à 96 x 144 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 845 mm Width x depth x height [mm] unit
Width x depth x height [mm]
720 x 480 x 48 5 pcs. à 96 x 336 x 48 1 set 81008353
5 pcs. à 96 x 240 x 48
5 pcs. à 96 x 96 x 48

91
6
Accessories SCALA XPRESS
Laboratory Accessories

For drawer depth 500 mm Drawer insert type A for Drawer inserts Sales Order no.
drawer width 900 mm Width x depth x height [mm] unit
Width x depth x height [mm]
792 x 480 x 48 2 pcs. à 144 x 384 x 48 1 set 81008354
4 pcs. à 144 x 192 x 48
4 pcs. à 144 x 144 x 48
2 pcs. à 96 x 192 x 48
1 pc. à 96 x 288 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 1145 mm Width x depth x height [mm] unit
Width x depth x height [mm]
960 x 480 x 48 1 pc. à 240 x 336 x 48 1 set 81008355
1 pc. à 144 x 384 x 48
5 pcs. à 144 x 144 x 48
8 pcs. à 144 x 192 x 48

Drawer insert type A for Drawer inserts Sales Order no.

drawer width 1200 mm Width x depth x height [mm] unit
Width x depth x height [mm]
1080 x 480 x 48 2 pcs. à 240 x 336 x 48 1 set 81008356
2 pcs. à 144 x 384 x 48
2 pcs. à 144 x 192 x 48
3 pcs. à 96 x 336 x 48
2 pcs. à 96 x 240 x 48
2 pcs. à 96 x 192 x 48

Scope of delivery
1 drawer insert type A
1 nop mat (dimensions correspond to the drawer insert type A)
4 adhesive pads

92
 SCALA XPRESS
Laboratory Accessories
6

Accessories
Supplementary drawer inserts Design characteristics Drawer insert Sales Order no.
type A Width x depth x unit
height [mm]
96 x 192 x 24 (3 1 81007191
drawer inserts)

144 x 192 x 24 (8 1 81007192

drawer inserts)

96 x 96 x 48 1 80009302

96 x 144 x 48 1 80009303

96 x 192 x 48 1 81005193

96 x 240 x 48 1 81007185

96 x 288 x 48 1 80009304

96 x 336 x 48 1 81007186

144 x 144 x 48 1 81007187

144 x 192 x 48 1 81007188

144 x 384 x 48 1 81007189

93
6
Accessories SCALA XPRESS
Laboratory Accessories

Supplementary drawer inserts Design characteristics Drawer insert Sales Order no.
type A Width x depth x unit
height [mm]
240 x 336 x 48 1 81007190

73 x 48 x 24 1 81007194
Depth infinitely
adjustable

Scope of delivery
5 drawer inserts (drawer insert with adjustable depth: 4 drawer inserts)

Nop mat Design characteristics Width x depth x Sales Order no.

height [mm] unit
480 x 480 x 3 1 81005195
(can be cut every
24 mm)

Scope of delivery
5 nop mats

Location pins Design characteristics Dimensions [mm] Sales Order no.

unit
Height 30, diam- 10 81007193
eter 24

Scope of delivery
10 location pins
20 screws

Assembly set Design characteristics Sales Order no.

unit
1 81010042

Scope of delivery
4 adhesive pads
2 cutting aids
1 universal knife
1 assembly instructions
94
 SCALA XPRESS
Laboratory Accessories – Bought-in products
6
Bimos chair, Flex 2 9409 model

Accessories
Properties
„„Adjustable seat height between 510-780 mm
„„360° revolving seat
„„Ergonomic and comfortable backrest

„„Extremely good grip, thanks to slip-resistant ‘wave’ seat finish

„„PU foam, black, washable, resilient and resistant to disinfection agents

„„Stable, topple-proof 5-star plastic base, with glides

Ordering information
Designation Order no.
Bimos chair, Flex 2 9409 model 80013951

Rinsing units
Designation Model Material Dimensions Order no.
W x H x D [mm]
Rinsing unit PG 8583 Stainless steel panelling 600 x 600 x 820 81014242
Rinsing unit PG 8583 CD CM Stainless steel panelling 900 x 600 x 820 81014775
Purifier PG 8595 D AE Stainless steel 300 x 600 x 820 81014243
excluding cartridge

!  Dishwashers only possible in Germany/Austria!

95
 SCALA XPRESS
Installation interfaces mechanical and electrical services

 For water and technical gases, shut-off valves

SCALA XPRESS

with 1/2” internal threads must be provided

on-site according to DIN EN 10226-2
 For pure gases, shut-off valves with 10 mm
clamp ring connections must be provided on-
site
 For waste water connections, a 56 mm plug
sleeve must be provided on-site.

 Electrical supply pipe in acc. with

DIN VDE 0100-430
 Type of cable/pipe with on-site fusing upon
agreement with Waldner

 Waldner will indicate the transfer points for

the on-site trades for each project in the cor-
res-ponding positional drawings

96
! Information: For drawings please consider interfaces!
Pre-conditions

! Exclusively items and products in this catalogue are valid for XPRESS

! Project volume is limited to 250.000 € and 600.000 €

! Approved final drawings to be submitted with purchase order

Please e-mail any questions or suggestions to the following address:

[email protected]

WALDNER Laboreinrichtungen SE & Co. KG

1560 · 0522

Haidoesch 1 · 88239 Wangen · Germany

Phone +49 7522 986-0 · Fax +49 7522 986-418
[email protected] · www.waldner.de