Nroom Technical Data Standard Units Update 02.2023

- Basic technical parameters - NRoom-100 (NR1-010-ECxxHR...) - Tab.
Line NR1-010-ECS0HRX… NR1-010-ECV1HRX…

Type of recovery exchanger HRV with temperatu
pre-heater - -
Unit equipment
after heater - water
Nominal airflow/ BOOST* m3/h 100/21
Heat output (range) of heating** kW - 0.33 - 1.38
Noise level** dB(A) 32.1
Weight**** kg 16.3 18.3
Water volume in exchanger l - 0.51
Power supply of the unit V/Hz 1 ~ 230 / 5
Nominal input power of the unit / BOOST* W 30/167 30/167
Nominal current of the unit / BOOST* A 0.3/1.32 0.3/1.32
Recovery efficiency per heat % up to 87
EN 308 humidity % - -
Protection type IP 20
Energy efficiency class (ERP) cold climate A+, medium clim
* BOOST mode - intensive ventilation
** at the temperature gradient of 75/60 and an inlet air temperature of 20 °C
*** Sound pressure level in free space at a distance of 3 m
**** unit weight, without water and packaging
- Basic technical parameters - NRoom-100 (NR1-01-ECxxER...) - Tab. 2
Line NR1-010-ECS0ERX… NR1-010-ECV1ERX…

Type of recovery exchanger ERV with temperature and
pre-heater - -
Unit equipment
Weight**** kg 16.3 18.3
EN 308 humidity % up to 85
NR1-010-ECE1HRX… NR1-010-ECS0HRP… NR1-010-ECV1HRP… NR1-010-ECE1HRP…
HRV with temperature efficiency
- electric electric electric
electric - water electric
100/215
0.5 - 0.33 - 1.38 0.5
32.1
19.3 16.8 18.8 19.8
- - 0.51 -
1 ~ 230 / 50-60
530/667 300/437 300/437 800/937
2.5/3.5 1.5/2.5 1.5/2.5 3.7/4.7
up to 87
- - - -
20
cold climate A+, medium climate A, warm climate A
NR1-010-ECE1ERX… NR1-010-ECS0ERP… NR1-010-ECV1ERP… NR1-010-ECE1ERP…

ERV with temperature and humidity efficiency
90/205
0.5 - 0.29 - 1.24 0.5
32.1
19.3 16.8 18.8 19.8
- - 0.51 -
1 ~ 230 / 50-60
530/667 300/437 300/437 800/937
2.5/3.5 1.5/2.5 1.5/2.5 3.7/4.7
up to 90
up to 85
20
cold climate A+, medium climate A, warm climate B
- Basic technical parameters - NRoom-250 (NR1-025-ECxxHR...) - Tab 3
Line NR1-025-ECS0HRX… NR1-025-ECV1HRX…

Type of recovery exchanger HRV with temperatu
pre-heater - -
Unit equipment
Weight**** kg 36 39.4
EN 308 humidity % - -
- Basic technical parameters - NRoom-250 (NR1-025-ECxxER...) - Tab. 4
Line NR1-025-ECS0ERX… NR1-025-ECV1ERX…

Type of recovery exchanger ERV with temperature and
pre-heater - -
Unit equipment
Weight**** kg 36 39.4
EN 308 humidity % up to 75
NR1-025-ECE1HRX… NR1-025-ECS0HRP… NR1-025-ECV1HRP… NR1-025-ECE1HRP…
HRV with temperature efficiency
250/350
1 - 1.34 - 3.49 1
32.6
41.2 37 40.4 42.2
- - 1.17 -
1 ~ 230 / 50-60
1061/1169 479/709 480/709 1480/1709
5/5.8 3/3.8 3/3.8 7.3/8.2
up to 87
- - - -
20
NR1-025-ECE1ERX… NR1-025-ECS0ERP… NR1-025-ECV1ERP… NR1-025-ECE1ERP…

ERV with temperature and humidity efficiency
240/335
1 - 1.34 - 3.49 1
32.6
41.2 37 40.4 42.2
- - 1.17 -
1 ~ 230 / 50-60
1061/1169 479/709 480/709 1480/1709
5/5.8 3/3.8 3/3.8 7.3/8.2
up to 86
up to 75
20
Weight
Line box Name Gross Net
kg kg
NR1-010-ECS0HRX… 19.2 16.3
NR1-010-ECV1HRX… 21.2 18.3
NR1-010-ECE1HRX… 22.2 19.3
NRoom unit
NR1-010-ECS0HRP… 19.7 16.8
NRoom-100
NR1-010-ECV1HRP… 21.7 18.8
NR1-010-ECE1HRP… 22.7 19.8
Mandatory
NR1-010-DUCT-1 1.4 1.2
accessories
NR1-025-ECS0HRX… 41.1 36
NR1-025-ECV1HRX… 44.5 39.4
NR1-025-ECE1HRX… 46.3 41.2
NRoom unit
NR1-025-ECS0HRP… 42.1 37
NRoom-250
NR1-025-ECV1HRP… 45.5 40.4
NR1-025-ECE1HRP… 47.3 42.2
Mandatory
NR1-025-DUCT-1 1.9 1.7
accessories
* package dimensions are indicated in the width x length x height order
number of units on a
package size * pallet - max.
stackability
m pc
1.05 x 0.7 x 0.31 5
0.6 x 0.4 x 0.21 40
1.6 x 0.84 x 0.36 5
0.6 x 0.4 x 0.21 40

- NR1-010-EC... - interior (indoor) radiation of the unit - Tab. 5
Degree of air output

125 Hz 250 Hz 500 Hz 1 kHz 2 kHz 4 kHz 8 kHz
1.- min/heating mode 21.5 dB 25.9 dB 29.7 dB 27.6 dB 21.0 dB 18.7 dB 17.5 dB
4. 28.8 dB 43.4 dB 41.3 dB 39.4 dB 34.3 dB 24.3 dB 18.0 dB
7.- nominal flow 32.0 dB 49.1 dB 48.7 dB 46.9 dB 43.0 dB 33.2 dB 23.1 dB
Boost* 42.0 dB 56.9 dB 67.1 dB 62.4 dB 59.5 dB 51.9 dB 45.2 dB
- NR1-010-EC... - exterior radiation of the unit (outdoor inlet, exhaust) - Tab. 6

1.- min/heating mode 34.7 dB 32.1 dB 35.8 dB 32.2 dB 22.0 dB 22.3 dB 24.7 dB
4. 46.4 dB 53.7 dB 49.7 dB 45.9 dB 35.9 dB 28.9 dB 25.4 dB
- NR1-025-EC... - interior (indoor) radiation of the unit - Tab. 7.

1.- min/heating mode
18.6 dB 29.5 dB 28.9 dB 25.7 dB 22.2 dB 15.8 dB 13.3 dB
4. 23.5 dB 42.6 dB 42.0 dB 37.6 dB 33.8 dB 21.9 dB 13.2 dB
- NR1-025-EC... - exterior radiation of the unit (outdoor inlet, exhaust) - Tab. 8

1.- min/heating mode
30.0 dB 36.5 dB 34.8 dB 29.9 dB 23.3 dB 18.9 dB 18.7 dB
4. 37.9 dB 52.6 dB 50.6 dB 43.8 dB 35.4 dB 26.0 dB 18.7 dB
Sound pressure level in the open field on the
Sound Power Level reflection plane
LWA [dB(A)]
LPA [dB] in 1 m LPA [dB] in 3 m
33.7 dB 19.8 dB 12.1 dB
47.0 dB 33.1 dB 25.5 dB
53.6 dB 39.7 dB 32.1 dB
69.3 dB 55.4 dB 47.8 dB

Sound power level reflection plane
LWA [dB (A)]
37.3 dB 23.7 dB 14.6 dB
52.1 dB 39.6 dB 30.8 dB
59.4 dB 47.5 dB 38.7 dB
76.8 dB 66.3 dB 57.6 dB

LWA [dB (A)]
34.4 dB 20.1 dB 12.7 dB

46.3 dB 31.9 dB 24.5 dB
54.2 dB 39.8 dB 32.6 dB
65.9 dB 51.5 dB 44.2 dB

LWA [dB (A)]
38.1 dB 24.0 dB 15.3 dB

51.3 dB 38.2 dB 29.6 dB
60.1 dB 47.6 dB 39.3 dB
73.1 dB 61.6 dB 53.3 dB
- sound permeability from the exterior
Line Nroom-100 Nroom-250

Evaluated acoustic Evaluated difference Evaluated acoustic
attenuation of the standard level attenuation
Degree of air output RW,P (C,Ctr) [dB] Dn, e, w (C,Ctr) [dB] RW,P (C,Ctr) [dB]
Standby 17 (-1; -3) 42 (-2; -3) 17 (-1; -3)
7.- nominal flow 17 (-1; -3) 42 (-1; -2) 17 (-1; -3)
Nroom-250
Evaluated difference
of the standard level
Dn, e, w (C,Ctr) [dB]
42 (-2; -3)
42 (-1; -2)
Technical data of water heaters
- NR1-010-ECV1HR… (heat recovery exchanger) - Tab. 10
Temperature gradient 80/60 75/65

Inlet air Heating Exhaust air Water Heating
temperatur Degree of air output Air flow power of a temperatur Water flow pressure power of a
e heater e drop heater
°C - m3/hr kW °C m3/hr kPa kW

1.- min/heating mode 28 0.47 75.3 0.02 0.2 0.42
10 4. 66 1.25 65.7 0.06 1 1.26
7.- nominal flow 100 1.78 60.6 0.08 1.7 1.76
1.- min/heating mode 28 0.4 74.9 0.01 0.2 0.38
15 4. 66 1.16 66.5 0.05 0.8 1.14
7.- nominal flow 100 1.62 61.7 0.07 1.2 1.6
1.- min/heating mode 28 0.35 74.9 0.01 0.2 0.35
20 4. 66 1.05 67.1 0.05 0.7 1.03
7.- nominal flow 100 1.46 62.7 0.06 1.2 1.44
- connection dimension male thread 3/4"
- NR1-010-ECV1HR… (heat recovery exchanger) - continued Tab. 10


1.- min/heating mode 28 0.35 60.9 0.02 0.3 0.28
10 4. 66 0.68 57.4 0.04 0.6 0.56
7.- nominal flow 100 1.4 49.8 0.08 2 1.17
1.- min/heating mode 28 0.31 60.9 0.03 0.2 0.25
15 4. 66 0.6 57.7 0.04 0.4 0.49
7.- nominal flow 100 1.24 50.9 0.07 1.6 1.02
1.- min/heating mode 28 0.26 60.8 0.01 0.2 0.2
20 4. 66 0.52 57.9 0.03 0.4 0.41
7.- nominal flow 100 1.09 51.8 0.06 1.3 0.86
- NR1-010-ECV1ER… (enthalpy recovery exchanger) - Tab.11


1.- min/heating mode 28 0.423 67.77 0.018 0.2 0.378
10 4. 66 1.125 59.13 0.054 0.9 1.134
7.- nominal flow 100 1.602 54.54 0.072 1.53 1.584
1.- min/heating mode 28 0.36 67.41 0.009 0.2 0.342
15
15 4. 66 1.044 59.85 0.045 0.72 1.026
7.- nominal flow 100 1.458 55.53 0.063 1.08 1.44
1.- min/heating mode 28 0.315 67.41 0.009 0.1 0.315
20 4. 66 0.945 60.39 0.045 0.63 0.927
7.- nominal flow 100 1.314 56.43 0.054 1.08 1.296
- NR1-010-ECV1ER… (enthalpy recovery ) - continued Tab.11


1.- min/heating mode 28 0.315 54.81 0.018 0.2 0.252
10 4. 66 0.909 48.51 0.054 0.99 0.756
7.- nominal flow 100 1.26 44.82 0.072 1.8 1.053
1.- min/heating mode 28 0.279 54.81 0.027 0.2 0.225
15 4. 66 0.801 49.05 0.045 0.81 0.657
7.- nominal flow 100 1.116 45.81 0.063 1.44 0.918
1.- min/heating mode 28 0.234 54.72 0.009 0.2 0.18
20 4. 66 0.702 49.5 0.045 0.63 0.558
7.- nominal flow 100 0.981 46.62 0.054 1.17 0.774
75/65 75/60 70/60
Exhaust air Water Heating Exhaust air Water Heating Exhaust air
temperatur Water flow pressure power of a temperatur Water flow pressure power of a temperatur Water flow
e drop heater e drop heater e
°C m3/hr kPa kW °C m3/hr kPa kW °C m3/hr

72.9 0.03 0.4 0.42 71.6 0.03 0.4 0.39 67.8 0.04
64.7 0.11 3.2 1.22 63 0.07 1.5 1.15 60.2 0.1
60.1 0.16 5.8 1.7 58.3 0.1 2.7 1.62 56 0.14
72.9 0.04 0.6 0.38 71.7 0.02 0.3 0.34 67.9 0.03
65.5 0.1 2.7 1.1 63.7 0.06 1.3 1.04 60.9 0.09
61.3 0.14 4.9 1.54 59.4 0.09 2.3 1.41 57.1 0.13
73 0.03 0.5 0.33 71.5 0.02 0.2 0.31 67.9 0.02
66.2 0.09 2.3 0.99 64.5 0.06 1 0.93 61.7 0.08
62.4 0.13 4.1 1.38 60.5 0.08 1.9 1.3 58.1 0.11
55/45 45/35 40/30


52.4 0.03 0.4 0.21 41.9 0.03 0.2 0.18 36.8 0.02
49.5 0.05 0.8 0.42 39.6 0.04 0.5 0.35 34.6 0.03
43.4 0.1 3.1 0.88 34.9 0.08 1.9 0.72 30.4 0.06
52.3 0.02 0.3 0.19 41.9 0.02 0.1 0.15 36.9 0.01
49.8 0.04 0.7 0.35 39.8 0.03 0.3 0.28 34.9 0.02
44.4 0.09 2.4 0.72 35.8 0.06 1.3 0.56 31.1 0.05
52.1 0.03 0.2 0.16 42.1 0.01 0.1 0.12 36.9 0.01
50 0.04 0.5 0.28 40.1 0.02 0.2 0.21 35.1 0.02
45.4 0.08 1.8 0.56 36.4 0.05 0.9 0.4 31.8 0.03
75/65 75/60 70/60


65.61 0.027 0.5 0.378 64.44 0.027 0.3 0.351 61.02 0.036
58.23 0.099 2.88 1.098 56.7 0.063 1.35 1.035 54.18 0.09
54.09 0.144 5.22 1.53 52.47 0.09 2.43 1.458 50.4 0.126
65.61 0.036 0.6 0.342 64.53 0.018 0.2 0.306 61.11 0.027
58.95 0.09 2.43 0.99 57.33 0.054 1.17 0.936 54.81 0.081
55.17 0.126 4.41 1.386 53.46 0.081 2.07 1.269 51.39 0.117
65.7 0.027 0.5 0.297 64.35 0.018 0.2 0.279 61.11 0.018
59.58 0.081 2.07 0.891 58.05 0.054 0.9 0.837 55.53 0.072
56.16 0.117 3.69 1.242 54.45 0.072 1.71 1.17 52.29 0.099
55/45 45/35 40/30


47.16 0.027 0.3 0.189 37.71 0.027 0.2 0.162 33.12 0.018
41.94 0.063 1.53 0.567 33.57 0.045 0.99 0.468 29.16 0.036
39.06 0.09 2.79 0.792 31.41 0.072 1.71 0.648 27.36 0.054
47.07 0.018 0.3 0.171 37.71 0.018 0.1 0.135 33.21 0.01
42.57 0.054 1.17 0.459 33.93 0.036 0.63 0.369 29.61 0.036
39.96 0.081 2.16 0.648 32.22 0.054 1.17 0.504 27.99 0.045
46.89 0.027 0.2 0.144 37.89 0.01 0.1 0.108 33.21 0.009
43.11 0.045 0.9 0.36 34.29 0.045 0.45 0.27 29.97 0.027
40.86 0.072 1.62 0.504 32.76 0.045 0.81 0.36 28.62 0.027
0/60 70/50
Water Heating Exhaust air Water
pressure power of a temperatur Water flow pressure
drop heater e drop
kPa kW °C m3/hr kPa

0.6 0.37 64.1 0.01 0.2
2.8 1.07 56.3 0.05 0.7
5.1 1.48 52 0.06 1.3
0.6 0.33 64.2 0.02 0.2
2.3 0.95 56.8 0.04 0.6
4.2 1.32 53 0.06 1.1
0.5 0.29 64.2 0.01 0.1
1.9 0.83 57.2 0.04 0.5
3.5 1.16 53.9 0.05 0.8
0/30
Water
pressure
drop
kPa
0.1
0.3
1.4
0.1
0.2
0.9
0.1
0.2
0.3
0/60 70/50
Water Heating Exhaust air Water
pressure power of a temperatur Water flow pressure
drop heater e drop

0.6 0.333 57.69 0.009 0.2
2.52 0.963 50.67 0.045 0.63
4.59 1.332 46.8 0.054 1.17
0.5 0.297 57.78 0.018 0.1
2.07 0.855 51.12 0.036 0.54
3.78 1.188 47.7 0.054 0.99
0.4 0.261 57.78 0.01 0.1
1.71 0.747 51.48 0.036 0.45
3.15 1.044 48.51 0.045 0.72
0/30
Water
pressure
drop
kPa
0.1
0.72
1.26
0.1
0.45
0.81
0.1
0.18
0.27
Technical data of water heaters
- NR1-025-ECV1HR... (heat recovery exchanger) -Table 12

Heating Water Heating
Inlet air Exhaust air
Degree of air output Air flow power of a Water flow pressure power of a
temperature temperature
heater drop heater

1.- min/heating mode 64 1.68 73.8 0.07 3.2 1.61
10 4. 157 2.87 68.1 0.12 8.1 2.78
7.- nominal flow 250 4.38 61.8 0.22 16.9 4.26
1.- min/heating mode 64 1.56 73.9 0.06 2.8 1.48
15 4. 157 2.65 68.6 0.11 7 2.57
7.- nominal flow 250 4 62.7 0.2 14.7 3.96
1.- min/heating mode 64 1.43 74.1 0.05 2.4 1.36
20 4. 157 2.44 69.1 0.1 6.1 2.35
7.- nominal flow 250 3.71 63.6 0.18 12.7 3.63
- NR1-025-ECV1HR… (heat recovery exchanger) - Tab. 10

heater drop heater

1.- min/heating mode 64 1.32 60.2 0.08 3.6 0.85
10 4. 157 2.26 55.7 0.13 9.2 1.44
7.- nominal flow 250 3.45 50.8 0.2 19.4 2.2
1.- min/heating mode 64 1.2 60.3 0.07 3 0.97
15 4. 157 2 56.2 0.12 7.7 1.66
7.- nominal flow 250 3.1 51.7 0.18 16.2 2.54
1.- min/heating mode 64 1.07 60.5 0.06 2.5 1.1
20 4. 157 1.82 56.7 0.11 6.3 1.88
7.- nominal flow 250 2.77 52.6 0.16 13.2 2.88
- NR1-025-ECV1ER... (enthalpy recovery exchanger) - Tab.13

heater drop heater

1.- min/heating mode 62 1.68 73.8 0.07 3.2 1.61
10 4. 151 2.87 68.1 0.12 8.1 2.78
7.- nominal flow 240 4.38 61.8 0.22 16.9 4.26
1.- min/heating mode 62 1.56 73.9 0.06 2.8 1.48
15 4. 151 2.65 68.6 0.11 7 2.57
7.- nominal flow 240 4 62.7 0.2 14.7 3.96
1.- min/heating mode 62 1.43 74.1 0.05 2.4 1.36
20 4. 151 2.44 69.1 0.1 6.1 2.35
7.- nominal flow 240 3.71 63.6 0.18 12.7 3.63
- NR1-025-ECV1ER... (enthalpy recovery exchanger) -continued Tab.13

heater drop heater

1.- min/heating mode 62 1.32 60.2 0.08 3.6 0.85
10 4. 151 2.26 55.7 0.13 9.2 1.44
7.- nominal flow 240 3.45 50.8 0.2 19.4 2.2
1.- min/heating mode 62 1.2 60.3 0.07 3 0.97
15 4. 151 2 56.2 0.12 7.7 1.66
7.- nominal flow 240 3.1 51.7 0.18 16.2 2.54
1.- min/heating mode 62 1.07 60.5 0.06 2.5 1.1
20 4. 151 1.82 56.7 0.11 6.3 1.88
7.- nominal flow 240 2.77 52.6 0.16 13.2 2.88
75/65 75/60 70/60
Water Heating Water Heating
Exhaust air Exhaust air Exhaust air
Water flow pressure power of a Water flow pressure power of a Water flow
temperature temperature temperature
drop heater drop heater

70.9 0.14 10 1.58 70 0.1 4.8 1.48 66.1 0.13
66.3 0.27 26.1 2.71 64.9 0.17 12.3 2.55 61.7 0.22
60.7 0.4 55.7 4.16 59.2 0.26 26 3.94 56.6 0.35
71.1 0.12 8.7 1.46 70.1 0.09 4.2 1.36 66.3 0.12
66.8 0.23 22.7 2.5 65.5 0.15 10.7 2.34 62.3 0.21
61.7 0.37 48.5 3.83 60.1 0.23 22.5 3.61 57.5 0.32
71.4 0.11 7.5 1.34 70.3 0.08 3.6 1.23 66.5 0.11
67.4 0.21 19.5 2.28 66 0.13 9.1 2.13 62.8 0.19
62.6 0.3 41.6 3.49 61.1 0.21 19.2 3.27 58.5 0.29
55/45 45/35 40/30


51.9 0.07 3.5 0.84 41.7 0.07 3.5 0.7 36.7 0.06
49 0.13 8.8 1.42 38.9 0.12 9 1.2 34.2 0.1
45.9 0.19 18.5 2.17 35.7 0.19 18.8 1.81 31.5 0.16
51.7 0.08 4.4 0.71 41.8 0.06 2.6 0.57 36.7 0.05
48.6 0.15 11.3 1.2 39.3 0.1 6.7 0.97 34.6 0.08
45 0.22 23.9 1.83 36.6 0.16 13.9 1.46 32.3 0.13
51.5 0.1 5.5 0.58 41.8 0.05 1.9 0.44 36.5 0.04
48 0.16 14 0.98 39.7 0.09 4.7 0.74 34.8 0.06
44.1 0.25 29.7 1.48 37.4 0.13 9.6 1.11 33 0.1
75/65 75/60 70/60


70.9 0.14 10 1.58 70 0.1 4.8 1.48 66.1 0.13
66.3 0.27 26.1 2.71 64.9 0.17 12.3 2.55 61.7 0.22
60.7 0.4 55.7 4.16 59.2 0.26 26 3.94 56.6 0.35
71.1 0.12 8.7 1.46 70.1 0.09 4.2 1.36 66.3 0.12
66.8 0.23 22.7 2.5 65.5 0.15 10.7 2.34 62.3 0.21
61.7 0.37 48.5 3.83 60.1 0.23 22.5 3.61 57.5 0.32
71.4 0.11 7.5 1.34 70.3 0.08 3.6 1.23 66.5 0.11
67.4 0.21 19.5 2.28 66 0.13 9.1 2.13 62.8 0.19
62.6 0.3 41.6 3.49 61.1 0.21 19.2 3.27 58.5 0.29
55/45 45/35 40/30


51.9 0.07 3.5 0.84 41.7 0.07 3.5 0.7 36.7 0.06
49 0.13 8.8 1.42 38.9 0.12 9 1.2 34.2 0.1
45.9 0.19 18.5 2.17 35.7 0.19 18.8 1.81 31.5 0.16
51.7 0.08 4.4 0.71 41.8 0.06 2.6 0.57 36.7 0.05
48.6 0.15 11.3 1.2 39.3 0.1 6.7 0.97 34.6 0.08
45 0.22 23.9 1.83 36.6 0.16 13.9 1.46 32.3 0.13
51.5 0.1 5.5 0.58 41.8 0.05 1.9 0.44 36.5 0.04
48 0.16 14 0.98 39.7 0.09 4.7 0.74 34.8 0.06
44.1 0.25 29.7 1.48 37.4 0.13 9.6 1.11 33 0.1
/60 70/50
Water Heating Water
Exhaust air
pressure power of a Water flow pressure
temperature
drop heater drop

8.8 1.42 63.9 0.06 2.4
22.9 2.41 58.8 0.11 6.1
48.8 3.66 53.3 0.16 12.8
7.6 1.3 64 0.06 2.1
19.6 2.19 59.2 0.1 5.2
41.8 3.32 54.1 0.15 10.8
6.4 1.17 64 0.05 1.7
16.6 1.97 59.7 0.09 4.3
35.3 2.98 55 0.13 8.9
/30
Water
pressure
drop
kPa
2.7
6.7
14
1.9
4.7
9.6
1.2
2.9
5.9
/60 70/50
Water Heating Water
Exhaust air
pressure power of a Water flow pressure
temperature
drop heater drop

8.8 1.42 63.9 0.06 2.4
22.9 2.41 58.8 0.11 6.1
48.8 3.66 53.3 0.16 12.8
7.6 1.3 64 0.06 2.1
19.6 2.19 59.2 0.1 5.2
41.8 3.32 54.1 0.15 10.8
6.4 1.17 64 0.05 1.7
16.6 1.97 59.7 0.09 4.3
35.3 2.98 55 0.13 8.9
/30
Water
pressure
drop
kPa
2.7
6.7
14
1.9
4.7
9.6
1.2
2.9
5.9
Line NRoom-100-e
Unit type NR1-010-ECxxHR…
Recovery exchanger type HRV
Temperature %
AIRFLOW
efficiency Current (A)
(m3/h)
(EN308)
1. 28 87 0.13
2. 41 85.1 0.14
3. 53 83.5 0.15
4. 66 81.7 0.18
5. 78 80 0.21
6. 90 78.3 0.26
7. - nominal 100 77 0.3
8. BOOST* 215 N/A 1.32
* BOOST mode - intensive ventilation for 10 minutes
EFFICIENCY CHART - NROOM-100 - HRV EFFIC

Temperature % efficiency (EN308)
88 Tempe
87
100
86
85 90
84
80
83
82 70
EFFICIENCY (%)
81
EFFICIENCY (%)
60
80
79 50
78 40
77
30
76
75 20
74
10
73
72 0
20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 20 25 30
FLOW RATE (m3/hr)

NRoom-100-efficiency of heat and humidity recovery
R… NR1-010-ECxxER…
ERV
Temperature % Humidity
Power supply AIRFLOW Power supply
efficiency efficiency % Current (A)
(W) (m3/h) (W)
(EN308) (EN308)
10 25 90 85 0.13 10
11 35 87 81 0.14 11
14 47 84 75 0.15 14
17 58 81 69 0.18 17
21 69 78 63 0.21 21
26 80 76 58 0.26 26
30 90 74 55 0.3 30
167 205 N/A N/A 1.32 167
EFFICIENCY CHART - NROOM-100 -

HRV, ERV
Temperature % efficiency (EN308) Humidity efficiency % (EN308)
100
90
80
70
EFFICIENCY (%)
60
50
40
30
20
10
0
20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110
FLOW RATE (m3/hr)
Line NRoom-250-e
Unit type NR1-025-ECxxHR…
Recovery exchanger type HRV
Temperature %
AIRFLOW
efficiency Current (A)
(m3/h)
(EN308)
1. 64 86.1 0.17
2. 95 85.0 0.20
3. 126 84 0.25
4. 157 83 0.32
5. 188 82 0.45
6. 219 81 0.52
7. - nominal 250 80.5 0.61
8. BOOST* 350 N/A 1.42
* BOOST mode - intensive ventilation for 10 minutes
EFFICIENCY CHART - NROOM-250 - HRV

Temperature % efficiency (EN308)
87.0
86.0
85.0
84.0
83.0
EFFICIENCY (%)
82.0
81.0
80.0
79.0
78.0
77.0
45 60 75 90 105 120 135 150 165 180 195 210 225 240 255 270
FLOW RATE (m3/hr)
NRoom-250-efficiency of heat and humidity recovery
R… NR1-025-ECxxER…
ERV
Temperature % Humidity
Power supply AIRFLOW Power supply
efficiency efficiency % Current (A)
(W) (m3/h) (W)
(EN308) (EN308)
13.5 62 85 73 0.17 13.5
17 92 82.5 70 0.20 17
23 121 81 67 0.25 23
30 151 79.5 64 0.32 30
40 180 78 60.5 0.45 40
51 210 76.5 58 0.52 51
61 240 75 54.5 0.61 61
169 335 N/A N/A 1.42 169
EFFICIENCY DIAGRAM - NROOM-250 -

HRV, ERV
Temperature % efficiency (EN308) Humidity efficiency % (EN308)
90
80
70
60
EFFICIENCY (%)
50
40
30
20
10
0
45 60 75 90 105 120 135 150 165 180 195 210 225 240 255 270
FLOW RATE (m3/hr)
Unit type Circuit breaker capacity Number of phases x voltage
NRoom 250 NRoom 100

NR1-010-ECS0…
NR1-010-ECV1… 10 A
NR1-010-ECE1…
1x230V
NR1-025-ECS0
10 A
NR1-025-ECV1
NR1-025-ECE1 16 A
- error messages - troubleshooting
Error No. Error, fault message Possible cause of failure Troubleshooting
- check the mains connection

The power cable is not connected
- check the activation of the safety element
1. The unit does not start The main switch is in position 0 - set the switch to position I
Hold down button 2 (ON/OFF) for a short - hold down button 2 (ON/OFF) until the LED above
time, approx. 3 sec button 2 lights up
- enter the unit setting mode and check the setting

of the ventilation performance requirement and the
The demand for ventilation and heating is required temperature (only in the version with
switched off electric heating)
The unit does not start when first - make the adjustment according to Section 5.4.2.
commissioned - LED above button 2 is Tab. 17.
lit
Loosened M6x20 bolts with plastic head - securely tighten the bolts on the front metal
position 23 of the front metal cover cover with your hand, Section 3.2.11.
Red indicator light above the FILTER

3. Filter clogging indication - replace the filter according to Section 6.
sign is flashing
No or low ventilation output even Clogged filter - replace the filter according to Section 6.
4. when the unit is set to the maximum
power Contaminated - blocked piping, unit
- Check and clean the unit according to Section 7.
outlets
Clogged filter - replace the filter according to Section 6.

5. Unit started to be too noisy
Defective motor bearing - contact the unit supplier
Clogged filter - no flow - replace the filter according to Section 6.
Contaminated - blocked piping, unit

- Check and clean the unit according to Section 7.
outlets
Electrical heating of the unit does not
6.
heat
- switch off the unit with the main switch. Turn the
activated heat exchanger protection
unit on again after 5 minutes (reset of protection). If
against overheating
the problem persists, contact the unit supplier
- wait for the outside temperature to rise. The

function is active only at summer temperatures.
The night cooling function cannot be
Function start conditions are not met - - for XR1-xxx-ECE1... reduce the temperature
switched on (button 6.) - the button
7. outdoor temperature is too low, heating requirement according to Section 5.4.2. Tab.17
signalling flashes 3 times and the
requirement is too high - for XR1-xxx-ECV1... the room air temperature
function does not switch on
exceeded 35 ° C - the function cannot be used
The night cooling function cannot be - switch off the BOOST functions according to
BOOST function active
switched on (button 6.) - all the status Section 5.4.2. Tab.17
8.
diodes flash once (at buttons 6, 4, 7, - switch off the child lock function according to
10), the function does not switch on Active child lock function
Section 5.4.2. Tab.17
The BOOST mode cannot be switched 3 flashes - very low outdoor temperature - wait for the outdoor temperature to rise
on - status diodes flash once or 3 times
9.
(at buttons 6, 4, 7, 10), the function - switch off the child lock function according to
does not switch on 1 flash - child lock function is active
3 flashes - unit is not fitted with any AQS - You probably bought the unit without the AQS
sensor sensors or the external sensor is not connected
- if you do not have an external Radon sensor

connected to the unit, contact the unit supplier
The automatic mode cannot be started - switch to manual mode according to Section 5.4.2.
10. - when the button 4 is pressed, the Tab.17
indicator flashes 3 times or lights It is still flashing - the sensor connected
to the unit is faulty
- if you have an external radon sensor connected to
the unit - contact the external sensor supplier
- switch to manual mode according to Section 5.4.2.
Tab.17
When any button is pressed, the status

- switch off the child lock function according to
11. diodes flash once (at buttons 6, 4, 7, Active child lock function
10)
- diodes 1; 2; 3; 4
12. The unit is Supply fan failure
are flashing
inoperable and the
- turn off the unit on the controller, then by the
4 LEDs on the - diodes 5; 6; 7; 8
13. Exhaust fan failure unit's main switch to position 18, leave the unit off
range for adjusting are flashing for approx. 10 sec - restart of the unit
the ventilation
- diodes 1; 2; 7; 8 - if the error persists even after restarting the unit,
14. power on the Faulty "room temperature sensor"
are flashing contact the unit supplier, contact the unit supplier
control panel are
after restarting the unit
continuously
flashing - diodes 3; 4; 5; 6
15. Faulty anti-freeze sensor
are flashing
- description of buttons
Active in mode / number of

Control
descripti Button/ clicks
Symbol Button description Dormant Control Settings Function Note
on Indication
number 0x 1x 2x
- Switches from the control mode to ventilation and temperature setting mode - Switching between setting the range of
Reduction of ventilation and
1. Button - Press the button to reduce the required level by one degree on the range of ventilation power or the ventilation power or required
temperature performance
temperature setting temperature is done using button 2.
Unit switching on - By holding the button for 3 seconds, switch the unit on (LED lights up) or off - in the cold and water versions, the display button
Toggle and (signalling)/switching off - if the LED flashes after the unit is switched off, the heating is cooled down. Once finished, it will turn off has only the on/off function
status
2.
indication
button Switching between ventilation - In setting mode, you switch between the fan setting and temperature ranges. Indication of the selected - Switching is only for the electric version
power and temperature setting range is displayed by flashing of symbols 7 and 10. (NR1-xxx-ECE1...)
Start of intensive ventilation - - Pressing the button for 3 seconds starts the intensive ventilation. To switch it off before 10 minutes pass, press the - The function start indication is a flashing
Toggle BOOST button again for 3 seconds and the ventilation returns to the pre-start mode. diode 12.
3. function
button Increase ventilation and - Switches from the control mode to ventilation and temperature setting mode - switch between the ranges using button
temperature power levels - Press the button to increase the requirement on the range of the ventilation or temperature performance setting 2.
- Factory setting is operation in the

- By pressing the button, switch to the manual mode, the requirement for permanent ventilation -
Status Switching between automatic automatic mode. Diode is lit
ventilation is operated upon request of the user, requirements of the AQS sensors are ignored
4. indication mode (signalling) and manual - When the unit is switched on, the LED
- Press again to activate automatic mode, ventilation as needed - ventilation is operated according to the
button mode diode next to the button is temporarily
AQS sensor requirements
flashing - sensor calibration
- The clogged filter indication is triggered after approx. 6 months of unit operation (only if the unit is
Status - Replace and reset the filter according to
5. Filter clogged indication ventilating).
indication Section 6.
- The indication is expressed by a flashing red LED.
- Press the button to start the night cooling function. Night cooling is used to cool the ventilated area in the
- It is recommended to activate the
Double- Night cooling - on summer with night cold air. The function is active for 8 hours from pressing the button.
function after 10 p.m. During the summer
function and (signalling)/off - The intensity of the supplied air can be changed even when the function is activated. When the function is
months, the air is coldest around 5 a.m.
6. status completed, the values return to the settings before the function started.
indication - When attempting to change the
button - protection against manipulation by unauthorised persons. It is activated/deactivated by pressing the
Child lock parameters during the activated function,
button for more than 6 sec. Activation/deactivation is indicated by 3 flashes of all the status LEDs
all the status LEDs flash once
- in the control mode, the diode is lit - the heating is on

– When heating is switched off (all the
Status Electric heating operation - in the setting mode, the diode flashes - you are in the desired temperature setting mode
7. range diodes are off), all the ventilation
indication status diode - heating can be switched off independently of the ventilation. In the setting mode, lower the temperature
functions remain operational.
(button 1) until the last diode on the range turns off
- in the control mode, the diode is lit - the unit is ventilating - When ventilation is switched off (all the
Status Ventilation operation status - in the setting mode, the diode flashes - you are in the required ventilation power setting mode range diodes are off), all the heating
10.
indication diode - ventilation can be switched off independently of the heating requirement. In the setting mode, reduce the requirements remain operational and
output (button 1) until the last diode on the range turns off. satisfied.
- ventilation range indication display
Control
descriptio Symbol
n number
11.
12.
Display description
Indication of 7 ventilation levels. The LEDs are switched on and off

gradually, as required by the user
Indication by flashing LED diode - intensive ventilation function

activated
Note
The setting values are provided in Tab.19.
If the intensive ventilation function is activated,

the entire range for setting the ventilation level
is also lit.
- Assignment of the individual LEDs to the air flow
Displayed LED on NR1-010-ECxxHR… NR1-010-ECxxER…

the controller Usage examples
range m3/h m3/h
1. 28 25 1 person - rest mode, sleeping
2. 41 35 2 persons - rest mode, sleeping
3. 53 47 2 persons - rest mode, sleeping
4. 66 58 3 persons - rest mode, office
5. 78 69 3 - 4 persons - rest mode, office
6. 90 80 4 persons – office activities
7. 101 90 4 - 5 persons - office activities
8. - BOOST* 215 204 Intensive ventilation
NR1-025-ECxxHR… NR1-025-ECxxER…
Usage examples
m3/h m3/h
64 62 2 - 3 persons - office activities, sleeping
95 92 3 - 4 persons - office activities, sleeping
126 121 4 - 5 persons – office activities, sleeping; 2 - 3 persons active
157 151 6 - 7 persons – office activities, 3 - 4 persons active
250 240 10 persons - office activities, 6 - 7 persons active
350 335 Intensive ventilation
- heating range indication display
Control
description Symbol Display description
number
Indication of temperature setting in
1st LED
8. 1st LED
2nd to 7th LED
LED in the separate MAX field - signals t
temperature requirement (ap
9.
Note:
The assignment of LEDs to the individual temperatures is only indicative. They cannot under any circumstances
Display description Note
dication of temperature setting in the selected range.
1st LED
Flake - anti-freeze temperature 5 - 7 °C
Regular temperature setting 19 - 24 °C setting in approx. 0.5 °C increments - LED
flashes
n the separate MAX field - signals the maximum possible
temperature requirement (approx. 28 °C)
y cannot under any circumstances be regarded as binding.

5.4.7. Display of the LED Indicated Statuses on the Controller
Status LED - fan - 10.

Blue
- lit - fan operation
- flashing - in the fan power setting mode
Status LED - heating - 7.
Blue
- lit - heater in operation
- flashing - heating power setting mode
Blue LED status diode - automatic (AQS)

/ manual (depending on the user) - 4.
- lit - automatic mode ON (AQS)
- flashing - failure of any AQS
Red LED status diode - filter clogging - 5.

- flashing - indicates filter clogging
Common functions for all the blue status diodes - 3 flashes for activation and
- 1 flash for indicating that t
- 3 flashes when starting th
Blue LED range diode - ventilation level - 11; 12
- Lit - shows the selected ventilation level
- LED 1; 2; 3; 4 flashing - supply fan failure
- LED 5; 6; 7; 8 flashing - exhaust fan failure
- LED 1; 2; 7; 8 flashing - “room temp sensor” failure
- LED 3; 4; 5; 6 flashing - “anti-freeze” sensor failure
LED blue range diode - temperature levels - 8; 9
- lit - displays the selected temperature
Blue LED status diode - ON/OFF

- lit - the unit controller - ON
- flashes – cooling mode after switching off the control
Blue LED status diode - summer mode - 6.

- lit - function activated
- 3 flashes - the function cannot be activated - poor ambient
conditions
s diode - filter clogging - 5.

indicates filter clogging
- 3 flashes for activation and deactivation of the "child lock" function
- 1 flash for indicating that the "child lock” function is active
- 3 flashes when starting the BOOST function - cannot be activated - low outdoor temperature
- Basic technical parameters - NRoom-100 (NR1-010-ECxxHR...)
Line NR1-010-ECS0...X… NR1-010-ECV1...X…

Type of recuperation exchanger HRV ERV HRV
pre-heating - -
Unit equipment
final heating - water
Nominal air output / BOOST* m3/hr 100/215 90/205 100/215
Noise level** dB(A)
Weight**** kg 16.3 18.3
Water volume in boiler l - 0.51
Power supply of the unit V/Hz
Nominal input power of unit / BOOST* W 30/167 30/167
Recovery efficiency per heat % up to 87 up to 90 up to 87
EN 308 humidity % - up to 85 -
Protection type IP
Energy efficiency ratio (ERP) cold climate A+ (-47 HRV, -45.9 ERV); medium cli
- Basic technical parameters - NRoom-250 (NR1-025-ECxxHR...)
Line NR1-025-ECS0...X… NR1-025-ECV1...X…

Type of recuperation exchanger HRV ERV HRV
pre-heating - -
Unit equipment
final heating - water
Nominal air output / BOOST* m3/hr 250/350 240/335 250/350
Noise level** dB(A)
Weight**** kg 36 39.4
Water volume in boiler l - 1.17
Power supply of the unit V/Hz
Nominal input power of unit / BOOST* W 61/169 61/169
Recovery efficiency per heat % up to 87 up to 86 up to 87
EN 308 humidity % - up to 75 -
Protection type IP
Energy efficiency ratio (ERP) cold climate A+ (-47.5 HRV, -47.2 ERV);
NR1-010-ECV1...X… NR1-010-ECE1...X… NR1-010-ECS0...P… NR1-010-ECV1...P… NR1-010-ECE1...P…
ERV HRV ERV HRV ERV HRV ERV HRV
- - electric electric electric
water electric - water electric
90/205 100/215 90/205 100/215 90/205 100/215 90/205 100/215
0.29 - 1.24 0.5 - 0.33 - 1.38 0.29 - 1.24 0.5
32.1
18.3 19.3 16.8 18.8 19.8
0.51 - - 0.51 -
1 ~ 230 / 50-60
30/167 530/667 300/437 300/437 800/937
0.3/1.32 2.5/3.5 1.5/2.5 1.5/2.5 3.7/4.7
up to 90 up to 87 up to 90 up to 87 up to 90 up to 87 up to 90 up to 87
up to 85 - up to 85 - up to 85 - up to 85 -
20
7 HRV, -45.9 ERV); medium climate A (-40,4 HRV, -38.9 ERV); warm climate A (-34.1 HRV), warm climate B (-33.1 ERV)
NR1-025-ECV1...X… NR1-025-ECE1...X… NR1-025-ECS0...P… NR1-025-ECV1...P… NR1-025-ECE1...P…

ERV HRV ERV HRV ERV HRV ERV HRV
- - electric electric electric
water electric - water electric
240/335 250/350 240/335 250/350 240/335 250/350 240/335 250/350
1.34 - 3.49 1 - 1.34 - 3.49 1
32.6
39.4 41.2 37 40.4 42.2
1.17 - - 1.17 -
1 ~ 230 / 50-60
61/169 1061/1169 479/709 479/709 1480/1709
0.61/1.42 5/5.8 3/3.8 3/3.8 7.3/8.2
up to 86 up to 87 up to 86 up to 87 up to 86 up to 87 up to 86 up to 87
up to 75 - up to 75 - up to 75 - up to 75 -
20
mate A+ (-47.5 HRV, -47.2 ERV); medium climate A (-40.5 HRV, -40.2 ERV); warm climate A (-34,6 HRV, -34,4)
NR1-010-ECE1...P…
ERV
electric
electric
90/205
0.5
19.8
-
800/937
3.7/4.7
up to 90
up to 85
ate B (-33.1 ERV)
NR1-025-ECE1...P…
ERV
electric
electric
240/335
1
42.2
-
1480/1709
7.3/8.2
up to 86
up to 75
-34,4)
Installation EPS box
Thermal
Type of installation EPS box conductivity thermal resistance approximate bulk
ordering code coefficient λ RD density
W/m.K m2.K/W kg/m3
NR-010-EPS-BOX
0.037 5.4 18 - 23
NR-025-EPS-BOX
*Number of pieces on the pallet
compressive stress packaging
at 10% compression fire reaction class net/gross weight dimensions
kPa - kg m (H x W x L)/pc*
0.9/1 0.45 x 0.2 x 0.5/32
100 E
1.1/1.2 0.54 x 0.2 x 0.5/32

Nroom Technical Data Standard Units Update 02.2023

Uploaded by

Copyright:

Available Formats

Nroom Technical Data Standard Units Update 02.2023

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nroom Technical Data Standard Units Update 02.2023

Uploaded by

Copyright:

Available Formats

- Basic technical parameters - NRoom-100 (NR1-010-ECxxHR...) - Tab.

Line NR1-010-ECS0HRX… NR1-010-ECV1HRX…

- Basic technical parameters - NRoom-100 (NR1-01-ECxxER...) - Tab. 2

Line NR1-010-ECS0ERX… NR1-010-ECV1ERX…

NR1-010-ECE1ERX… NR1-010-ECS0ERP… NR1-010-ECV1ERP… NR1-010-ECE1ERP…

Line NR1-025-ECS0HRX… NR1-025-ECV1HRX…

- Basic technical parameters - NRoom-250 (NR1-025-ECxxER...) - Tab. 4

Line NR1-025-ECS0ERX… NR1-025-ECV1ERX…

NR1-025-ECE1ERX… NR1-025-ECS0ERP… NR1-025-ECV1ERP… NR1-025-ECE1ERP…

1.05 x 0.7 x 0.31 5

0.6 x 0.4 x 0.21 40

1.6 x 0.84 x 0.36 5

0.6 x 0.4 x 0.21 40

Degree of air output

- NR1-010-EC... - exterior radiation of the unit (outdoor inlet, exhaust) - Tab. 6

Degree of air output

- NR1-025-EC... - interior (indoor) radiation of the unit - Tab. 7.

Degree of air output

- NR1-025-EC... - exterior radiation of the unit (outdoor inlet, exhaust) - Tab. 8

Degree of air output

Sound pressure level in the open field on the

Sound pressure level in the open field on the

34.4 dB 20.1 dB 12.7 dB

Sound pressure level in the open field on the

38.1 dB 24.0 dB 15.3 dB

Line Nroom-100 Nroom-250

Temperature gradient 80/60 75/65

°C - m3/hr kW °C m3/hr kPa kW

- NR1-010-ECV1HR… (heat recovery exchanger) - continued Tab. 10

Temperature gradient 65/50 55/45

°C - m3/hr kW °C m3/hr kPa kW

- NR1-010-ECV1ER… (enthalpy recovery exchanger) - Tab.11

Temperature gradient 80/60 75/65

°C - m3/hr kW °C m3/hr kPa kW

- NR1-010-ECV1ER… (enthalpy recovery ) - continued Tab.11

Temperature gradient 65/50 55/45

°C - m3/hr kW °C m3/hr kPa kW

°C m3/hr kPa kW °C m3/hr kPa kW °C m3/hr

55/45 45/35 40/30

°C m3/hr kPa kW °C m3/hr kPa kW °C m3/hr

75/65 75/60 70/60

°C m3/hr kPa kW °C m3/hr kPa kW °C m3/hr

55/45 45/35 40/30

°C m3/hr kPa kW °C m3/hr kPa kW °C m3/hr

kPa kW °C m3/hr kPa

kPa kW °C m3/hr kPa

Temperature gradient 80/60 75/65

°C - m3/hr kW °C m3/hr kPa kW

- NR1-025-ECV1HR… (heat recovery exchanger) - Tab. 10

Temperature gradient 65/50 55/45

°C - m3/hr kW °C m3/hr kPa kW

- NR1-025-ECV1ER... (enthalpy recovery exchanger) - Tab.13

Temperature gradient 80/60 75/65

°C - m3/hr kW °C m3/hr kPa kW

- NR1-025-ECV1ER... (enthalpy recovery exchanger) -continued Tab.13

Temperature gradient 65/50 55/45

°C - m3/hr kW °C m3/hr kPa kW

°C m3/hr kPa kW °C m3/hr kPa kW °C m3/hr