1-Phase Power Supply, Primary Switch Mode

for Use in Potentially Explosive Areas

QUINT-PS-100-240AC/24DC/10/EX
QUINT POWER provides:
• Preventive function monitoring through
professional signaling
• Global use due to a wide range input
• A high level of operational safety even in complex
global networks
• Reliable startup of heavy loads due to
POWER BOOST
The reliability of a power supply determines the
availability of individual components in a system and
whether complex systems can function safely.
The globalization of markets increases the demands
placed on the power supply. A wide range input and a
high level of availability are required.
These requirements are met by Generation 2
QUINT POWER.

1. Short Description
QUINT POWER is the universal 24 V supply of
60 - 960 W. Output currents of 2.5, 5, 10, 20, 30, and
40 A are available at an adjustable and regulated
output voltage of 22.5 - 28.5 V DC. Output currents of
5 A and 10 A are available for use in potentially
explosive areas of zone 2.
These devices, which are designed as primary
switched-mode regulators, operate with a high level of 2. Area of Application
efficiency so that heat loss is kept to a minimum.
The high level of operational safety is also ensured in The power supply corresponds to the EN 50021
complex global networks. QUINT POWER also standard and may be installed within a potentially
operates in applications where static voltage dips, explosive area, in which Category 3 equipment is
transient power supply failures or phase failure are required.
common. The power supply is suitable for use in Class I,
Large capacitors ensure mains buffering of more Division 2, Groups A, B, C, and D.
than 20 ms at full load. All 3-phase QUINT POWER QUINT POWER can be used globally due to the
units provide the complete output power even in the consistent provision of a wide range input.
event of a continuous phase failure. In this way, your entire system can be tested at any
Reliable startup of heavy loads is ensured by a production location in the world and can be delivered to
power reserve of up to 50% - the POWER BOOST. any location in the world without faulty switching of the
Preventive function monitoring diagnoses an input voltage. This reduces storage costs and logistical
impermissible operating state and minimizes effort.
downtimes in your system. An active transistor output An international approval package including
and an electrically isolated relay contact are provided CB Scheme, UL 60950 for IT equipment, and UL 508
for remote monitoring of this state. for industrial control equipment enables the device to
This signal not only provides information on the device be used globally.
function, but also indicates a system overload at an Safe operation in adverse conditions is emphasized
early stage. by the approval of the entire product range by
Germanischer Lloyd.

Headquarters: © Phoenix Contact GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany
Phone +49 - 52 35 - 30 0 • Fax +49 - 52 35 - 34 12 00 • www.phoenixcontact.com
Local Contact: www.phoenixcontact.com/salesnetwork
1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

3. Technical Data

125 mm
(4.921 in.)

L (+)
activ e

(5.118 in.)
130 mm
PFC
N (–)

PE DC OK
13
14

85 mm
(3.346 in.)

QUINT 24 V DC/10 A/EX

Scheme U uFB
1 AC CB
7 solid flexible torque
[mm2] AWG [Nm] [Ib in.]

Input 0.2 - 2.5 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3

Output 0.2 - 2.5 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3
Signal 0.2 - 2.5 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3

Pcs.
Description Type Order No. Pkt.
Power Supply
Primary switch mode for potentially explosive areas QUINT-PS-100-240AC/24DC/10/EX 29 38 86 6 1

Technical Data

Input Data 1
Nominal input voltage 100 - 240 V AC (wide range input)
Input voltage range 85 - 264 V AC 90 - 250 V DC
Frequency 45 - 65 Hz 0 Hz
Current consumption (for nominal values) 2.8 A (120 V AC)/1.2 A (230 V AC), approximately
Inrush current limiting/I2t (+25°C [+77°F]) 15 A, approximately/1.5 A2s, approximately
Mains buffering for a nominal load (typical) > 40 ms (120 V AC)/> 40 ms (230 V AC)
Switch-on time after applying the mains voltage <1s
Transient surge voltage protection Varistor
Input fuse, internal 6.3 AT (device protection)
Recommended fuse Circuit breaker 10 A or 16 A
Characteristic B (EN 60 898)
Discharge current for PE < 3.5 mA
Output Data 2
Nominal output voltage UN/tolerance 24 V DC ±1%
Setting range for the output voltage 22.5 - 28.5 V DC
Output current (continuous) during convection cooling and nominal
values POWER BOOST IBOOST -25°C to +40°C (-13°F to +104°F) 15 A (Uout = 24 V DC)
Nominal output current IN -25°C to +60°C (-13°F to +140°F) 10 A (Uout = 24 V DC)
Short-circuit current limit IBOOST ≈ 15 A, approximately
Startup of capacitive loads Unlimited
System deviation on: Load change static 10 - 90% < 1%, typical
Load change dynamic 10 - 90% < 2%, typical
Input voltage change ±10% < 0.1%, typical
Maximum power dissipation No load/nominal load 4 W/33 W, approximately
Efficiency > 88% (for 230 V AC and nominal values)
Response time UOUT (10% - 90%) < 2 ms, typical
Residual ripple/switching peaks (20 MHz) < 100 mVpp (for nominal values)
Can be connected in parallel To increase redundancy and power
Internal surge voltage protection Yes, limited to 35 V DC, approximately
Resistance to return supply 35 V DC
Signal Output Data
DC OK (active) 3 +24 V DC signal (with regard to the device weight)
(Uout > 0.9 x UN = high signal) 40 mA, maximum
DC OK (electrically isolated) 4 30 V AC/DC, maximum; 1 A, maximum, ohmic load
(Uout > 0.9 x UN = contact closed)
LED 6 (Uout < 0.9 x UN = LED flashing) Green LED

PHOENIX CONTACT page 2 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

General Data
Insulation voltage: Input/output 4 kV AC (type test)/2 kV AC (routine test)
Input/PE 3.5 kV AC (type test)/2 kV AC (routine test)
Output/PE 707 V DC (routine test)
Approval package B
Electrical equipment of machines EN 60 204 (Surge Voltage Category III)
Safety transformers for switched-mode power supply units EN 61 558-2-17
Electrical safety EN 60950/VDE 0805,
(of IT equipment) UL/C-UL Recognized UL 60 950 u
Industrial control equipment UL/C-UL Listed UL 508 U
Shipbuilding Germanischer Lloyd F LISTED
Equipping high voltage installations
with electronic equipment EN 50 178 (VDE 0160)
Safety extra-low voltage PELV (EN 60 204)
SELV (EN 60 950)
Safe isolation VDE 0100-410
Protection against electric shock DIN 57100-410
Protection against dangerous shock currents,
basic requirements for safe isolation
in electrical equipment DIN VDE 0106-101
Limitation of harmonic line currents According to EN 61000-3-2
Conformance mark according to EN 50021 X II 3G EEx nAC IIC T4 TÜV 03 ATEX 2047X
Electrical equipment for explosion-protected areas UL/c-UL Recognized UL 1604 Class I, Division 2, Groups A, B, C, D
Mounting position On horizontal NS 35 DIN rail according to EN 50022
Can be mounted with spacing Vertical with ≥ 5 cm (1.969 in.)/horizontal 0 cm
Degree of protection IP 20
Class of protection Ι, with PE connection
MTBF > 500 000 h according to IEC 1709 (SN 29 500)
Housing version AluNox (AlMg1), closed
Dimensions (W x H x D) + DIN rail Default upon delivery: Rotated 90°:
(85 x 130 x 125 mm( 122 x 130 x 88 mm
[3.346 x 5.118 x 4.921 in.]) [4.803 x 5.118 x 3.465 in.])
Weight 1.3 kg, approximately
Climatic Data
Ambient temperature Operation -25°C to +60°C/+40°C (-13°F to +140°F/104°F)
Storage -40°C to +85°C (-40°F to +185°F)
Humidity Up to 100% at +25°C (+77°F), condensation permitted
Vibration according to IEC 68-2-6 < 15 Hz, amplitude ±2.5 mm/15 Hz - 150 Hz, 2.3 g, 90 minutes
Shock according to IEC 68-2-27 30 g all space directions
Degree of pollution 2 (according to EN 50 178)
Climatic category 3K3 (according to EN 60 721)

c
Conforms to the EMC Directive 89/336/EEC and the
Low Voltage Directive 73/23/EEC
EMC (Electromagnetic Compatibility) Requirements QUINT-PS-100-240AC/24DC/10/
Noise Immunity According to EN 61000-6-2: EN 61 000-6-2 EX

Electrostatic discharge EN 61000-4-23) Housing Level 4

(ESD) Contact discharge: 4 kV 8 kV
Air discharge: 8 kV 15 kV
Electromagnetic EN 61000-4-32) Housing Level 3
HF field Frequency: 80 - 1000 MHz 80 - 1000 MHz/1.4 - 2.0 GHz
Field strength: 10 V/m 10 V/m
Fast transients EN 61000-4-43) Input: 2 kV asymmetrical5) 4 kV (Level 4)
(burst) Output: 2 kV asymmetrical5) 2 kV (Level 3)
Signal: 1 kV asymmetrical5) 1 kV (Level 2)
Surge current loads EN 61000-4-53) Input: 2 kV asymmetrical5) 4 kV (Level 4)
1 kV symmetrical4) 2 kV (Level 4)
Output: 0.5 kV asymmetrical5) 0.5 kV (Level 1)
0.5 kV symmetrical4) 0.5 kV (Level 1)
Signal: 1 kV asymmetrical5) 1 kV (Level 2)
Conducted EN 61000-4-62) I/O/S: asymmetrical5) Level 3
interference Frequency: 0.15 - 80 MHz 0.15 - 80 MHz
U0: 10 V 10 V
Voltage dips EN 61000-4-113) Input: 30% reduction of the input voltage See input data:
for 0.5 periods Mains buffering
>20 ms
Simulation of EN 50204 Frequency: Not required 900 MHz/1800 MHz
radiophone Field strength: 20 V/m
Noise Emission According to EN 50081-2:
Radio interference EN 55011 Class A6) EN 55011 (EN 55022) Class B7)
6)
Radio interference EN 55011 Class A EN 55011 (EN 55022) Class B7)
EN 55011 corresponds to CISPR11/EN 55022 corresponds to CISPR22
EN 61000 corresponds to IEC 1000
4)
symmetrical:
Cable to cable
2) 5)
Criterion A: Normal operating characteristics within the specified asymmetrical: Cable to ground
limits.
3) 6)
Criterion B: Temporary adverse effects on the operating Class
A: Industrial application
7)
characteristics that the device corrects independently. Class B: Industrial and domestic applications

PHOENIX CONTACT page 3 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

4. Device View, Connections, and Control Elements

13
14 D
OKC
+
+
–
13 –

QUINT POWER
4 1 D
O 4 OC
ut K
13
14 D
OKC
pu + +
tD
C
+– 13
+
–
–
/24
DC
/10
/E
X

.2A

www.interface.phoenixcontact.com
14 D -1

2
4V – O
ut OC
K
pu + 0
40
AC
-2 6 6 0Hz VA
0 8 8 -6 64
/2.8C

10
A
tD
C
+–
2
4V –
10
S-19 3 /50 5-2
T-P 2 AC e 8
IN No.: 40V ag
QU er- 0-2 Volt
l
Ord.: 10ona VD A
0 0
C
6
A Inperati -35 C/1
p 0
O .: 9 4V D x
xx

3 DC
Inptp.:2
Ou

RE
xx
x
xx V x
x
x

…
+
°C
60 °F
40
5 +1
O -2 …
K OK 3
DC -1
x
22 A xx 5 0
.5- d ju –2 95
DC 28 st
.5V
60 04 -17
EN 602 8-2
5
EN 615

B
T4 EN
S
AL C -2

5
nA ... 0 -6
OVEx EX 00
61 81-1
PR G E AT
L
IA EN 500
AP II Ü3V03 USTORL T
T D R N EN
IN NT ME ns
COUIP ct
io s
EQD4 ru a i n
X st
in o m
U
1

2 AC In
LIS
TE
D

st
ll
a ec
in o n n
io
n
at t i n g
t

1 pu
L 00-2t
4
N 0V
F ad c
R ef o r e
be
5
1
Figure 04

1 AC input: When installing and operating electrical equipment,

Input voltage 85 - 264 V AC/90 - 250 V DC the applicable national safety standards and the
Frequency 45 - 65 Hz general technical regulations (e.g., EN 60 079-14 VDE
(0.2 mm2 to 2.5 mm2 solid) 0165 Part 1) must be observed. It is particularly
(0.2 mm2 to 2.5 mm2 flexible) important to ensure that:
(25 - 14 AWG) – The mains have been connected correctly and
Internal fuse 6.3 AT protection is provided against electric shock.
Recommended fuse – The device can be switched off outside the power
10 A or 16 A c.b./Characteristic B supply according to EN 60950 regulations (e.g., by
2 DC output: the line protection on the primary side).
Output voltage 24 V DC (default), can be set from – The protective conductor is connected.
22.5 - 28.5 V DC using a potentiometer 5 (0.2 mm2 – All supply lines and outgoing cables have sufficient
to 2.5 mm2 solid) (0.2 mm2 to 2.5 mm2 flexible) fuse protection and are the correct size for the
(25 - 14 AWG) current flow.
The device is idling-proof and short-circuit-proof. – Installation is carried out following the instructions
3 DC OK output active provided.
4 DC OK output electrically isolated – The specified mechanical or thermal limits are not
5 Potentiometer (covered) 22.5 - 28.5 V DC exceeded during operation.
6 DC OK LED – At least IP 54 protection according to EN60529 is
7 Universal DIN rail adapter UTA 107 achieved after installation.
– If dust is present, the device must be installed in
5. Safety Notes and Warning suitable housing.
– Only devices, which are suitable for operation in
Instructions potentially explosive areas of zone 2 and are suited
to the conditions at the installation location can be
To ensure safe operation of the device, please read connected to supply and signal circuits in zone 2.
these instructions carefully. – When using a DC input voltage of more than 120 V,
Installation, startup, and maintenance must only be a suitable fuse must be fitted.
carried out by qualified personnel. The relevant
country-specific safety rules and regulations for the
prevention of accidents must also be observed.

Caution: Never carry out work when the

power is turned on, this is highly
dangerous. The circuits inside the device
must not be accessed during operation.

PHOENIX CONTACT page 4 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

6. Installation
6.1. Mounting
The power supply can be snapped onto all DIN rails
according to EN 50022-35 and should be mounted
horizontally (input terminal blocks facing downwards).

Installation Dimensions

To ensure sufficient convection, we

QUINT POWER
13
14 D
OKC
+
recommend a minimum spacing of 5 cm 13
+
–
–
/24
DC
/10
/E
X

.2A

www.interface.phoenixcontact.com
1 D .8-1
O 4 OC AC
40 6 Hz/2AC

(1.969 in.) to other modules above and ut K

pu
t
+
DC +–
24V
10
– IN N 4
QU er- 0-2 Volta
l
Ord.: 10 na VD A
0
-2
00 8 86 -60 64V
S-19 3 /50 5-2
T-Po.: 2 VACge 8

below the device. No minimum spacing

0 0
A Inperatio-35 C/1
Op .: 904VD xx
x
Inptp.:2
Ou °C
x
xx V xx 60
RE

to other modules at the sides is required DC

22 A
O
K
DC
OK
xx
x

xx
x
5
-1
5
-2 …
3
+ … 14
+ 0 °F

for proper operation of the device.

0
.5-2dju –2 95
60 04 -17
8.5st EN 602 8-2
V 5
EN 615

B
T4 EN
S
AL nAC...
-2
0-6

The housing temperature can reach high PR

OV EExTEX
AP II Ü3G
T
A RIA
V03 USTOL T
D R N
IN NT ME
COUIP
L

EN
00
61 81-1
EN 500

ns
ti o s
EQD4 u c in

values depending on the ambient AC In

ULI
ST
ED
1X

s ta e
in o n n
n
ti o g
ll a c ti n
in
s tr m a
to

temperature and the load of the device.

1 pu
L 00-2t
N 40V
F e ad c
R fo re
be
5

Figure 05

Narrow mounting position: Flat mounting position:

Installation depth 125 mm (4.921 in.) (+ DIN rail) Installation depth 88 mm (3.465 in.) (+ DIN rail)

85 mm (3.346 in.) 122 mm (4.803 in.)

50 mm (1.969 in.)
115 mm (4.528 in.)

QUINT POWER

DC
13 14 OK ++– –
Output DC 24V 10A
130 mm (5.118 in.)
230 mm (9.055 in.)

DC OK

Adjust
22.5-28.5V

Input
AC 100-240V
L N 5

Figure 06

PHOENIX CONTACT page 5 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

6.2. Narrow Mounting Position

The device is supplied ex works for a narrow
mounting position.

Mounting:
Place the module with the DIN rail guideway on the
Mounting
top edge of the DIN rail and then snap it downwards.
Removal:
Release the snap-on catch using a screwdriver and
then detach the module from the bottom edge of the
DIN rail.

6.3. Flat Mounting Position

A flat mounting position can be achieved by
mounting the module onto the DIN rail at a 90° angle. Removal
To do this, mount the DIN rail adapter (UTA 107) 7 as
shown in Figure 08. No additional mounting material is
required. Mounting screws: Torx T10
(torque 0.8 - 0.9 Nm/7 - 8 Ib in.).

Figure 07

Figure 08

PHOENIX CONTACT page 6 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

6.4. Connection of Various Types of Network: 100 - 240 V AC Networks

TN-S network TN-C network TT network IT network
L L L
N PEN N
PE

L N PE L N PE L N PE
+ – + – + –
QUINT QUINT QUINT

L1 L1 L1 L1
L2 L2 L2 L2
L3 L3 L3 L3
N PEN N
PE

L N PE L N PE L N PE L N PE
+– +– +– +–
QUINT QUINT QUINT QUINT
Figure 09

Connection Cable:
The device is equipped with COMBICON
connectors. This reliable user-friendly connection
method enables quick device connection and safe
isolation of the electrical connection, if required. Only
operate connectors when the power is switched off.
To maintain UL approvals, use copper cables, which
are designed for operating temperatures of 75°C
(167°F). To maintain GL approval, unused terminal AC In
compartments should be closed. 1 pu
L 00-2t
The following cable cross sections can be connected: N4 0V
Solid
[mm2]
Flexible
[mm2]
AWG
[Nm]
Torque
[Ib in.]
5
1 Input: 0.2 - 2.5 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3
2 Output: 0.2 - 2.5 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3
3 Signal: 0.2 - 2.5 0.2 - 2.5 25 - 14 0.5 - 0.6 4.4 - 5.3

For reliable and safe-to-touch 7 mm (0.28 in.)

connection: Strip 7 mm (0.28 in.)
from the connector ends. Figure 10
To maintain EN 60 950/UL 60 950,
flexible cables require ferrules.
Additional device protection is not required, as an
internal fuse is present.
6.5. Input (1, Figure 10)
The 100 - 240 V AC connection is made using screw
connections L, N, and 5.
Recommended Fuse:
Circuit breaker 10 A or 16 A, Characteristic B (or
The device can be connected to single-phase
equivalent). No more than one power supply should be
AC networks or to two external conductors for three-
connected to a fuse or a power switch. When using a
phase networks (TN, TT or IT network according to
DC input voltage of more than 120 V, a suitable fuse
VDE 0100 T 300/IEC 364-3) with nominal voltages of
must be fitted.
100 - 240 V AC.

Protecting the Primary Side If the internal fuse is blown, this is most
The device must be installed according to the probably due to a device fault. In this
specifications of EN 60 950. It must be possible to case, the device should be checked and/
switch off the device using a suitable disconnecting or repaired in the factory. The power
device outside the power supply. Note that an all-pole supply unit cannot be repaired by the
disconnecting device must be provided for two-phase user and must be replaced by an
operation using two external conductors for a three- equivalent device.
phase network. For example, primary side line
protection could be used.

PHOENIX CONTACT page 7 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

6.6. Output (Figure 11)

During operation only devices, which are suitable for 4 3 2
operation in potentially explosive areas of zone 2, can

QUINT POWER
be connected to the output voltage in zone 2. 13
14 D
The 24 V DC connection is made using the "+" and OKC
+
"-" screw connections on the screw connection 2. The +
–
output voltage set upon delivery is 24 V DC. 13 –
1 D
The output voltage can be adjusted from 22.5 to O 4 OC
ut K
28.5 V DC on the potentiometer 5. The output voltage pu +
tD
C
+–
cannot be adjusted during operation in potentially 2
4V –
10
explosive areas. A

Protecting the Secondary Side:

The device is electronic short-circuit-proof and idling- DC
proof. In the event of an error, the output voltage is
O
K 5
limited to a maximum of 35 V DC. 22 A
.5- dju
28 st
It should be ensured that all output cables are the .5V
correct size for the maximum output current or have
separate fuse protection.
The secondary side cables should have large cross
sections to keep voltage drops on the cables to a Figure 11
minimum.
External decoupling diodes are required for
redundancy operation of these power supplies.
For example, the QUINT-DIODE/40 redundancy
module could be used (Order No.: 29 38 96 3).

Signaling
Both DC OK outputs are used for preventive function
Output 24V DC
monitoring of the power supply. An electrically isolated

DC OK
signal contact 4 and an active DC OK signal 3 are
available. In addition, the DC OK LED 6 can be used 13 14 + + – –
to evaluate the function of the power supply directly at
the installation location.

Green "DC OK" LED ON Flashing OFF

DC OK
Active
DC OK switching output U = 24 V U = 0V U = 0V
max.
(with reference to "-") 30 VAC/DC, 1 A
Electrically isolated
DC OK output Closed Open Open

Meaning Output voltage Output voltage No voltage at the

greater than 90% less than 90% of output Figure 12
of the set voltage the set voltage

Description Output voltage QUINT POWER QUINT POWER

and current OK operating, but: not operating,
• Error at the load because:
• Current • No mains
consumption voltage present
greater than • Primary side
IBOOST fuse is blown
• Output short • Device is faulty
circuit

Electrically Isolated Contact (Figure 12)

When opened, the electrically isolated signal contact
indicates that the output voltage has fallen more than
10% below the set value. Signals and ohmic loads up
to a maximum of 30 V and currents up to a maximum
of 1 A can be switched.
With heavy inductive loads, e.g., a relay, a suitable
protective circuit (e.g., free-wheeling diode) is required.

PHOENIX CONTACT page 8 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

Active Signal Output (Figure 13)

The 24 V DC signal is between the "DC OK" and "-"
connection terminal blocks and can be loaded with
40 mA maximum. This signal output indicates that the
output voltage has fallen more than 10% below the set
value when "active high" changes to "low".
The DC OK signal is isolated from the power output. Output 24V DC
This ensures that a separate supply does not enter

DC OK
from devices connected in parallel.
The 24 V DC signal can be connected directly to the
logic input for evaluation.
13 14 + + – –
Signal Loop (Figure 14)
The two signal outputs mentioned above can be 24 V DC
max. 40 mA DC OK
combined easily.

Example: Monitoring two devices

Use the active alarm output of device 1 and loop in
the electrically isolated alarm output of device 2. In the
event of an error, a group error message is generated.
It is possible to loop any number of devices. Figure 13
This signal combination saves on wiring costs and
logic inputs.

DC OK LED
The green DC OK LED enables local function
evaluation in the control cabinet.
Device 1 Device 2
LED ON Normal operation of the power supply
LED The output voltage has fallen by more than 10%. Output 24V DC Output 24V DC
flashing There is a secondary load short circuit or overload
DC OK

DC OK
outside the POWER BOOST area.
LED OFF No mains voltage is present or there is a device fault.
13 14 + + – – 13 14 + + – –
24 V DC
DC OK
7. Function 40 mA

7.1. Output Characteristic Curve

The device can supply a nominal output current of
10 A up to an ambient temperature of 60°C (140°F).
With an ambient temperature of up to 40°C (104°F) the
device continuously supplies an output current of 15 A.
At temperatures up to 60°C (140°F), the Figure 14
POWER BOOST provides a short-term output current
of 15 A for a few minutes.
With high loads, the working point demonstrates the
U/I characteristic curve shown in Figure 15.
On an overload or short circuit, the entire output
current I BOOST is provided permanently at a reduced
output voltage. UOUT
Once the overload or short circuit has been removed, [V] 240 W 360 W
the entire set secondary voltage is available again.
The U/I characteristic curve ensures that both heavy UN 24
capacitive loads and devices with DC/DC converters
can be supplied by QUINT POWER in the input circuit < 40 °C
without any problems.
Connected fuses are reliably tripped. The selectivity
in your system configuration is ensured at all times.
10 15 IOUT
IN IBOOST [A]

Figure 15

PHOENIX CONTACT page 9 of 10

1-Phase Power Supply, Primary Switch Mode for Use in Potentially Explosive Areas –
QUINT 24 V DC/10A/EX

7.2. Temperature Response

The device can supply a nominal current of 10 A up
to an ambient temperature of 60°C (140°F). With an
ambient temperature of up to 40°C (104°F) the device UOUT = 24 V
continuously supplies an output current of 15 A. At

Output current [A]

15
temperatures up to 60°C (140°F), the POWER BOOST
10
provides a short-term output current of 15 A for a few
minutes.
The device does not switch off in the event of a
thermal overload. The output power is decreased to 0
such an extent that device protection is provided. Once 0 20 40 60
the device has cooled, the output power is increased
again. Ambient temperature [°C]

7.3. Parallel Operation Figure 16

Devices of the same type can be connected in
parallel to increase both redundancy and power. The
default setting does not have to be adjusted.
If the output voltage is adjusted, an even current
distribution can be ensured by precisely setting all
power supplies that are operated in parallel to the QUINT QUINT
same output voltage. 10 A + – 10 A + –
To ensure symmetrical current distribution we
recommend that all cable connections from the power
supply to the DIN rail are the same length and have the +
same cross section. –
Depending on the system, for parallel connection of
more than two power supplies a protective circuit
should be installed at each individual device output + – Σ = 10 A
(e.g., redundancy module or DC fuse). This means that
in the event of a secondary device fault high return
currents are avoided. Figure 17

7.4. Redundancy Operation (Figure 17)

Redundant connections are designed for supplying
systems, which place particularly high requirements on
operational safety. If a fault occurs in the primary circuit
of device 1, device 2 automatically takes over the QUINT QUINT

http://www.phoenixcontact.com
10 A + – 10 A + –
complete power supply without interruption and vice
versa.
For this purpose, the power supplies to be connected
in parallel must be large enough that the total current +
requirements of all loads can be fully met by one power –
supply.
External decoupling diodes are required for 100%
redundancy. For example, the QUINT-DIODE/
+ – Σ = 20 A
40 redundancy module could be used
(Order No.: 29 38 96 3).
Figure 18
TNR: 5156043-01

7.5. Power Increase (Figure 18)

The output current can be increased to n x IN where
n is the number of devices connected in parallel.
The parallel connection for power increase can be
used to extend existing systems. A parallel connection
is recommended if the power supply does not cover the
05/01/03

current consumption of the most powerful load.

Otherwise, the loads should be divided over
independent individual devices.
A maximum of five devices can be connected in
 PHOENIX CONTACT

parallel.

PHOENIX CONTACT page 10 of 10