REM615 PG 756890 ENp

—
RELION® 615 SERIES
Motor Protection and Control REM615

Product Guide
Motor Protection and Control REM615 1MRS756890 P
Contents
1 Description............................................................... 3 26 Cyber security........................................................ 56
2 Standard configuration..........................................3 27 Terminal diagrams................................................ 56
3 Protection functions.............................................10 28 Certificates.............................................................60
4 Application..............................................................10 29 References..............................................................60
5 Supported ABB solutions..................................... 12 30 Functions, codes and symbols........................... 60
6 Control..................................................................... 14 31 Document revision history.................................. 63
7 Measurement..........................................................15
8 Disturbance recorder............................................ 15
9 Event log..................................................................15
10 Recorded data ....................................................... 15
11 Condition monitoring........................................... 16
12 Trip-circuit supervision........................................ 16
13 Self-supervision..................................................... 16
14 Fuse failure supervision....................................... 16
15 Current circuit supervision.................................. 17
16 Access control........................................................ 17
17 Inputs and outputs................................................ 17
18 Station communication........................................18
19 Technical data........................................................ 22
20 Local HMI................................................................. 51
21 Mounting methods............................................... 53
22 Relay case and plug-in unit..................................53
23 Selection and ordering data................................53
24 Accessories and ordering data...........................53
25 Tools........................................................................ 55
Disclaimer Conformity
The information in this document This product complies with following directive and
is subject to change without notice regulations.
and should not be construed as a
commitment by ABB. ABB assumes no Directives of the European parliament and of the council:
responsibility for any errors that may • Electromagnetic compatibility (EMC) Directive
appear in this document. 2014/30/EU
© Copyright 2022 ABB • Low-voltage Directive 2014/35/EU
• RoHS Directive 2011/65/EU
All rights reserved.
Trademarks UK legislations:
ABB and Relion are registered • Electromagnetic Compatibility Regulations 2016

trademarks of the ABB Group. All • Electrical Equipment (Safety) Regulations 2016
other brand or product names • The Restriction of the Use of Certain Hazardous
mentioned in this document may be Substances in Electrical and Electronic Equipment
trademarks or registered trademarks Regulations 2012
of their respective holders.
These conformities are the result of tests conducted by
the third-party testing in accordance with the product
standard EN / BS EN 60255-26 for the EMC directive /
regulation, and with the product standards EN / BS EN
60255-1 and EN / BS EN 60255-27 for the low voltage
directive / safety regulation.
The product is designed in accordance with the
international standards of the IEC 60255 series.
2 REM615
Product Guide
1. Description 2. Standard configuration
REM615 is a dedicated motor protection and REM615 is available with four alternative
control relay designed for the protection, standard configurations. The standard signal
control, measurement and supervision of configuration can be altered by means of
asynchronous motors in manufacturing and the graphical signal matrix or the graphical
process industry. REM615 is a member of ABB’s application functionality of the Protection and
®
Relion product family and part of its 615 Control IED Manager PCM600. Further, the
protection and control product series. The application configuration functionality of the
615 series relays are characterized by their relay supports the creation of multi-layer
compactness and withdrawable-unit design. logic functions using various logical elements
including timers and flip-flops. By combining
Re-engineered from the ground up, the 615
protection functions with logic function blocks,
series has been designed to unleash the
the relay configuration can be adapted to user-
full potential of the IEC 61850 standard for
specific application requirements.
communication and interoperability between
substation automation devices. Once the The relay is delivered from the factory with
standard configuration relay has been given the default connections described in the functional
application-specific settings, it can directly be diagrams for binary inputs, binary outputs,
put into service. function-to-function connections and alarm
LEDs. Some of the supported functions in
The 615 series relays support a range of
REM615 must be added with the Application
communication protocols including IEC 61850
Configuration tool to be available in the Signal
with Edition 2 support, process bus according
Matrix tool and in the relay. The positive
to IEC 61850-9-2 LE, IEC 60870-5-103, Modbus
® and DNP3. Profibus DPV1 communication measuring direction of directional protection
functions is towards the outgoing feeder.
protocol is supported by using the protocol
converter SPA-ZC 302.
REM615 3
Product Guide
REM615 MOTOR PROTECTION AND CONTROL RELAY STANDARD

CONFIGURATION
A
PROTECTION LOCAL HMI ALSO AVAILABLE
- Disturbance and fault recorders

2× 3× - Event log and recorded data
Master Trip Master Trip
- High-Speed Output module (optional)
Configuration A
System
Lockout relay Lockout relay

HMI
Time
Authorization
- Local/Remote push button on LHMI

94/86 94/86 I ESC Clear
- Self-supervision
- Time synchronization: IEEE 1588 v2,
A
O R
L
U12 0. 0 kV
P 0.00 kW
SNTP, IRIG-B
3I
Q 0.00 kVAr
2× - User management
IL2 0 A
3I< I2>M I2>> - Web HMI

37 46M 46R I
AND
ESC Clear
O R
L
OR
Is2t n< 3Ith>M

49, 66, 48, 51LR 49M
CONDITION MONITORING COMMUNICATION

3× 3× AND SUPERVISION
ARC 3I>>> Io Protocols:
50L/50NL 50P/51P
IEC 61850-8-1
Modbus®
IEC 60870-5-103
3I>/Io>BF Ist> CBCM MCS 3I OPTS DNP3
51BF/51NBF 51LR CBCM MCS 3I OPTM Interfaces:
Ethernet: TX (RJ45), FX (LC)
Serial: Serial glass fiber (ST),
2× RS-485, RS-232
3I> 3I>> TCS
Redundant protocols:
51P-1 51P-2 TCM
HSR
PRP
RSTP
Io
CONTROL AND INDICATION 1) MEASUREMENT
Io - I, Io
Io> Io>> Object Ctrl 2) Ind 3)
51N-1 51N-2 - Limit value supervision
CB 1 - - Load profile record
- RTD/mA measurement (optional)
DC 2 3 - Symmetrical components
ES 1 2
1)
Check availability of binary inputs/outputs Analog interface types 1)
from technical documentation Current transformer 4

2)
Control and indication function for
primary object Voltage transformer -
3)
Status indication function for
primary object
1)
Conventional transformer inputs
ESTART
ESTART
REMARKS
18× Optional 3× No. of Calculated OR Alternative
MAP function instances value function to be
MAP Io/Uo defined when
6xRTD ordering
2xmA
Figure 1: Functionality overview for standard configuration A
4 REM615
Product Guide
UL1UL2UL3

CONFIGURATION
B

Configuration A
System
HMI

Time
Authorization

94/86 94/86 I ESC Clear
- Self-supervision
A
O R
L
U12 0. 0 kV
P 0.00 kW
SNTP, IRIG-B
3I
Q 0.00 kVAr
IL2 0 A

37 46M 46R I
AND
ESC Clear
O R
L
OR
Is2t n< 3Ith>M

49, 66, 48, 51LR 49M

ARC 3I>>> Protocols:
50L/50NL 50P/51P 3I Io
IEC 61850-8-1/-9-2LE
Modbus®
IEC 60870-5-103
3I>/Io>BF Ist> FUSEF CBCM MCS 3I DNP3
51BF/51NBF 51LR 60 CBCM MCS 3I Interfaces:
2× RS-485, RS-232
3I> 3I>> OPTS TCS Redundant protocols:
51P-1 51P-2 OPTM TCM HSR
PRP
RSTP
Io Io
Io>>
51N-2
Io - I, U, Io, P, Q, E, pf, f
Object Ctrl 2) Ind 3) - Limit value supervision
- RTD/mA measurement (optional)
DC 2 3 - Symmetrical components
Io>→
67N-1 ES 1 2
1)

Uo 2)
primary object Voltage transformer 3
UL1UL2UL3
3)
primary object
1)
UL1UL2UL3 2×
3U< U2> U1< f>/f<, ESTART
df/dt
27 47O- 47U+ ESTART
81
REMARKS
6xRTD ordering
2xmA
Figure 2: Functionality overview for standard configuration B
REM615 5
Product Guide
Uo
UL1UL2UL3

CONFIGURATION
C

Configuration A
System

HMI
Time
Authorization

94/86 94/86 I ESC Clear
- Self-supervision
A
O R
L
U12 0. 0 kV
P 0.00 kW
SNTP, IRIG-B
3I
Q 0.00 kVAr
IL2 0 A

37 46M 46R I
AND
ESC Clear
O R
L
OR
Is2t n< 3Ith>M

49, 66, 48, 51LR 49M

50L/50NL 50P/51P
3I Io
IEC 61850-8-1/-9-2LE
Modbus®
IEC 60870-5-103
2× RS-485, RS-232
PRP
RSTP
Io Io
Io>>
51N-2
Io - I, U, Io, Uo, P, Q, E, pf, f
Object Ctrl 2) Ind 3) - Limit value supervision
- Symmetrical components
Uo DC 2 3
Io>→
67N-1 ES 1 2
1)

2)
2)
UL1UL2UL3
3)
primary object
1)
2)
One of the five inputs is reserved for
future applications
UL1UL2UL3 2×
df/dt
27 47O- 47U+ ESTART
81
REMARKS
ordering
Figure 3: Functionality overview for standard configuration C
6 REM615
Product Guide
UL1UL2UL3

CONFIGURATION
D

Configuration A
System

HMI
Time
Authorization

94/86 94/86 I ESC Clear
- Self-supervision
A
O R
L
U12 0. 0 kV
P 0.00 kW
SNTP, IRIG-B
3I
Q 0.00 kVAr
IL2 0 A

37 46M 46R I
AND
ESC Clear
O R
L
OR
Is2t n< 3Ith>M

49, 66, 48, 51LR 49M

50L/50NL 50P/51P
3I Io
IEC 61850-8-1/-9-2LE
Modbus®
IEC 60870-5-103
2× RS-485, RS-232
PRP
RSTP
Io Io
Io>>
51N-2
Io - I, U, Io, P, Q, E, pf, f
Object Ctrl 2)
Ind 3)
- Limit value supervision
- Symmetrical components
DC 2 3
Io>→
67N-1 ES 1 2
1)
from technical documentation Current sensor 3

Uo 2)
primary object Voltage sensor 3
UL1UL2UL3
3)
1)
Combi sensor inputs with conventional
2× Io input
df/dt
27 47O- 47U+ ESTART
81
REMARKS
ordering
Figure 4: Functionality overview for standard configuration D
Table 1: Standard configuration
Description Std. conf.
Basic motor protection (RTD option) A
Motor protection with voltage and frequency based protection and measurements (RTD option) B
Motor protection with voltage and frequency based protection and measurements C
Motor protection with voltage and frequency based protection and measurements (sensor inputs) D
Table 2: Supported functions
Function IEC 61850 A B C D
Protection
Three-phase non-directional overcurrent protec- PHLPTOC 1 1 1 1

tion, low stage
Table continues on the next page
REM615 7
Product Guide
No EFLPTOC for this
configuration
Three-phase non-directional overcurrent protec- PHHPTOC 1 1 1 1

tion, high stage
Three-phase non-directional overcurrent protec- PHIPTOC 1 1 1 1

tion, instantaneous stage
Non-directional earth-fault protection, low EFLPTOC 1

stage
Non-directional earth-fault protection, high EFHPTOC 1 1 1 1

stage
Directional earth-fault protection, low stage DEFLPDEF 1 1 11
Three-phase undervoltage protection PHPTUV 1 1 1
Positive-sequence undervoltage protection PSPTUV 1 1 1
Negative-sequence overvoltage protection NSPTOV 1 1 1
Frequency protection FRPFRQ 2 2 2
Negative-sequence overcurrent protection for MNSPTOC 2 2 2 2

machines
Loss of load supervision LOFLPTUC 1 1 1 1
Motor load jam protection JAMPTOC 1 1 1 1
Motor start-up supervision STTPMSU 1 1 1 1
Phase reversal protection PREVPTOC 1 1 1 1
Thermal overload protection for motors MPTTR 1 1 1 1
Circuit breaker failure protection CCBRBRF 1 1 1 1
Master trip TRPPTRC 2 2 2 2
(3) (3) 2 (3) 2 (3) 2
Arc protection ARCSARC (3) (3) (3) (3)
Multipurpose protection MAPGAPC 18 18 18 18
Control
Circuit-breaker control CBXCBR 1 1 1 1
Disconnector control DCXSWI 2 2 2 2
Earthing switch control ESXSWI 1 1 1 1
Disconnector position indication DCSXSWI 3 3 3 3
Earthing switch indication ESSXSWI 2 2 2 2
Emergency start-up ESMGAPC 1 1 1 1
Condition monitoring and supervision
Circuit-breaker condition monitoring SSCBR 1 1 1 1
Trip circuit supervision TCSSCBR 2 2 2 2
Current circuit supervision CCSPVC 1 1 1 1
1 "Uo calculated" is always used.

2 Master trip is included and connected to the corresponding HSO in the configuration only when
the BIO0007 module is used. If additionally the ARC option is selected, ARCSARC is connected in
the configuration to the corresponding master trip input.
8 REM615
Product Guide
Fuse failure supervision SEQSPVC 1 1 1
Runtime counter for machines and devices MDSOPT 1 1 1 1
Measurement
Disturbance recorder RDRE 1 1 1 1
Load profile record LDPRLRC 1 1 1 1
Fault record FLTRFRC 1 1 1 1
Three-phase current measurement CMMXU 1 1 1 1
Sequence current measurement CSMSQI 1 1 1 1
Residual current measurement RESCMMXU 1 1 1 1
Three-phase voltage measurement VMMXU 1 1 1
Residual voltage measurement RESVMMXU 1
Sequence voltage measurement VSMSQI 1 1 1
Three-phase power and energy measurement PEMMXU 1 1 1
RTD/mA measurement XRGGIO130 (1) (1)
Frequency measurement FMMXU1 1 1 1
IEC 61850-9-2 LE sampled value sending SMVSENDER (1) (1) (1)
IEC 61850-9-2 LE sampled value receiving (volt- SMVRCV (1) (1) (1)
age sharing) 3, 4
Other
Minimum pulse timer (2 pcs) TPGAPC 4 4 4 4
Minimum pulse timer (2 pcs, second resolution) TPSGAPC 1 1 1 1
Minimum pulse timer (2 pcs, minute resolution) TPMGAPC 1 1 1 1
Pulse timer (8 pcs) PTGAPC 2 2 2 2
Time delay off (8 pcs) TOFGAPC 4 4 4 4
Time delay on (8 pcs) TONGAPC 4 4 4 4
Set-reset (8 pcs) SRGAPC 4 4 4 4
Move (8 pcs) MVGAPC 2 2 2 2
Generic control point (16 pcs) SPCGAPC 2 2 2 2
Analog value scaling (4 pcs) SCA4GAPC 4 4 4 4
Integer value move (4 pcs) MVI4GAPC 1 1 1 1
1, 2, ... = Number of included instances. The instances of a protection function represent the number of identical protection
function blocks available in the standard configuration.
() = optional
3 Available only with IEC 61850-9-2

4 Available only with COM0031-0037
REM615 9
Product Guide
3. Protection functions 4. Application
The relay offers all the functionality needed REM615 constitutes main protection for
to manage motor start-ups and normal asynchronous motors and the associated
operation, also including protection and fault drives. Typically, the motor relay is used
clearance in abnormal situations. The main with circuit breaker or contactor controlled
features of the relay include thermal overload HV motors, and contactor controlled medium
protection, motor start-up supervision, locked sized and large LV motors in a variety of
rotor protection and protection against drives, such as pumps and conveyors, crushers
too frequent motor start-ups. The relay and choppers, mixers and agitators, fans and
also incorporates non-directional earth-fault aerators.
protection, negative phase-sequence current
The motor relay is thoroughly adapted for
unbalance protection and backup overcurrent
earth-fault protection. Using cable current
protection. Furthermore, the relay offers
transformers sensitive and reliable earthfault
motor running stall protection, loss-of-load
protection can be achieved. Phase current
supervision and phase reversal protection.
transformers in Holmgreen (summation)
Standard configurations B, C and D additionally connection can also be used for earthfault
offer directional earth-fault protection, three- protection. In that case possible unwanted
phase undervoltage protection, negative- operations of the earth-fault protection at
sequence overvoltage and positive-sequence motor start-up due to CT saturation can be
undervoltage protection. Further, the B, C and prevented using the relay's internal interlocking
D configurations offer frequency protection features or a suitable stabilizing resistor in the
including overfrequency, underfrequency and common neutral return.
rate-of-change frequency protection modes.
The optional RTD/mA module offered for
The RTD/mA module offered as an option for standard configurations A and B facilitates the
standard configurations A and B enables the measurement of up to eight analog signals
use of the optional multipurpose protection via the six RTD inputs or the two mA inputs
function for tripping and alarm purposes using using transducers. The RTD and mA inputs can
RTD/mA measuring data or analog values via be used for temperature monitoring of motor
GOOSE messages. bearings and stator windings, thus expanding
the functionality of the thermal overload
In certain motor drives of special importance
protection and preventing premature aging of
there must be a possibility to override the
the motor. Furthermore, the RTD/mA inputs
motor thermal overload protection to perform
can be used for measuring the ambient cooling
an emergency start of a hot motor. To enable
air temperature. The analog temperature values
an emergency hot start, REM615 offers a forced
can, if required, be sent to other devices
start execution feature.
using analog horizontal GOOSE messaging.
Enhanced with optional hardware and software, Temperature values can also be received from
the relay also features three light detection other devices over the station bus, thus
channels for arc fault protection of the circuit increasing the extent of relevant information.
breaker, busbar and cable compartment of
The standard configuration D includes one
metalenclosed indoor switchgear.
conventional residual current (Io) input and
The arc-fault protection sensor interface is three combi-sensor inputs for phase currents
available on the optional communication and phase voltages. The connection of the
module. Fast tripping increases staff safety three combi-sensors is made with RJ-45 type of
and security and limits material damage in connectors.
an arc fault situation. A binary input and
Sensors offer certain benefits compared to
output module can be selected as an option -
conventional current and voltage instrument
having three high speed binary outputs (HSO)
transformers, for example, current sensors
it further decreases the total operate time
do not saturate at high currents, they
with typically 4...6 ms compared to the normal
consume less energy and they weigh less. In
power outputs.
voltage sensors the risk of ferro-resonance is
10 REM615
Product Guide
eliminated. The sensor inputs also enable the for conventional measuring transformers, thus
use of the relay in compact medium voltage requiring the use of sensor technology. Further,
switchgears, such as ABB’s UniGear Digital, the adapters also enable the use of sensors
SafeRing and SafePlus, with limited space with Twin-BNC connectors.
REF615
Std. conf. C/D
ANSI IEC
46 I2>
Io
50L/50NL ARC
50P/51P 3I>>>
50N/51N-1/51N-2 Io>>>/Io>>/Io>
3I 51BF/51NBF 3I>/Io>BF
68 3I2f>
3I
3I
Io 3U Uo
Io
RTD RTD
REM615 REU615 REM615

Std. conf. B Std. conf. A Std. conf. A
ANSI IEC ANSI IEC ANSI IEC
37 3I< 47O-/59 U2>/3U> 37 3I<

46R I2>> 47U+/27 U1</3U< 46R I2>>
47O-/59 U2>/3U> 50L/50NL 1)
ARC 1)
49,66,48,51LR Is2t n<
47U+/27 U1</3U< 59G Uo> 49M 3Ith>M
49,66,48,51LR Is2t n< 81 f</f>,df/dt 50L/50NL ARC
49M 3Ith>M 81LSH UFLS/R 51N-1/51N-2 Io>>/Io>
50L/50NL ARC 1)
Light detection only 50P/51P 3I>>>
51N-2/67N-1 Io>>/Io> -> 51LR Ist>
50P/51P 3I>>> 51P/51N 3I/Io
51LR Ist>
51P/51N 3I/Io
Figure 5: Motor protection and control of contactor and circuit breaker controlled motors using
standard configurations A and B
Figure 5 illustrates an example of motor collapse, the simultaneous starting of several

protection and control of contactor and circuit motors can be inhibited with the "restart
breaker controlled motors using standard inhibit" input of REM615. The optional RTD/mA
configurations A and B. To prevent possible inputs are utilized for motor winding and
power system instability due to busbar voltage bearing temperature supervision.
REM615 11
Product Guide
REF615
Std. conf. L
ANSI IEC
Io 47O-/59 U2>/3U>
47U+/27 U1</3U<
3U 50L/50NL ARC
50P/51P 3I>>>
3I 51BF/51NBF 3I>/Io>BF
67 3I→
3I
3I
3U 3U
Io
Io
RTD RTD
REM615 REM615
Std. conf. D Std. conf. D
ANSI IEC ANSI IEC
37 3I< 37 3I<
46R I2>> 46R I2>>
47O-/59 U2>/3U> 47O-/59 U2>/3U>
47U+/27 U1</3U< 47U+/27 U1</3U<
49,66,48,51LR Is2t n< 49,66,48,51LR Is2t n<
49M 3Ith>M 49M 3Ith>M
50L/50NL ARC 50L/50NL ARC
50P/51P 3I>>> 50P/51P 3I>>>
51LR Ist> 51LR Ist>
51P/51N 3I/Io 51P/51N 3I/Io
Figure 6: Motor protection and control of contactor and circuit breaker controlled motors using
standard configuration D
Example of motor protection and control of

contactor and circuit breaker controlled motors 5. Supported ABB solutions
using standard configuration D is shown in
Figure 6. In this configuration current sensors
The 615 series protection relays together with
(Rogowski coil) and voltage sensors (voltage
the Substation Management Unit COM600S
divider) are used for the measurements. To
constitute a genuine IEC 61850 solution
prevent possible power system instability due
for reliable power distribution in utility and
to busbar voltage collapse, the simultaneous
industrial power systems. To facilitate the
starting of several motors can be inhibited
system engineering, ABB's relays are supplied
with the "restart inhibit" input of REM615. The
with connectivity packages. The connectivity
optional RTD/mA inputs are utilized for motor
packages include a compilation of software and
winding and bearing temperature supervision.
relay-specific information, including single-line
The standard configuration D has been pre- diagram templates and a full relay data model.
configured especially for ABB switchgears, for The data model includes event and parameter
example, UniGear Digital. The use of this lists. With the connectivity packages, the relays
configuration is not restricted for that purpose can be readily configured using PCM600 and
only. integrated with COM600S or the network
12 REM615
Product Guide
control and management system MicroSCADA provides an overview of the whole substation,
Pro. including relay-specific single-line diagrams,
which makes information easily accessible.
The 615 series relays offer native support
Substation devices and processes can also be
for IEC 61850 Edition 2 also including binary
remotely accessed through the Web HMI, which
and analog horizontal GOOSE messaging.
improves personnel safety.
In addition, process bus with the sending
of sampled values of analog currents and In addition, COM600S can be used as a
voltages and the receiving of sampled values of local data warehouse for the substation's
voltages is supported. Compared to traditional technical documentation and for the network
hard-wired, inter-device signaling, peer-to-peer data collected by the devices. The collected
communication over a switched Ethernet LAN network data facilitates extensive reporting
offers an advanced and versatile platform and analyzing of network fault situations by
for power system protection. Among the using the data historian and event handling
distinctive features of the protection system features of COM600S. The historical data can
approach, enabled by the full implementation be used for accurate monitoring of process
of the IEC 61850 substation automation and equipment performance, using calculations
standard, are fast communication capability, based on both real-time and historical values.
continuous supervision of the protection and A better understanding of the process
communication system's integrity, and an dynamics is achieved by combining time-based
inherent flexibility regarding reconfiguration process measurements with production and
and upgrades.This protection relay series maintenance events.
is able to optimally utilize interoperability
COM600S can also function as a gateway
provided by the IEC 61850 Edition 2 features.
and provide seamless connectivity between
At substation level, COM600S uses the data the substation devices and network-level
content of the baylevel devices to enhance control and management systems, such as
substation level functionality. COM600S MicroSCADA Pro and System 800xA.
features a Web browser-based HMI, which
GOOSE Analyzer interface in COM600S enables
provides a customizable graphical display
the following and analyzing the horizontal IEC
for visualizing single-line mimic diagrams for
61850 application during commissioning and
switchgear bay solutions. The SLD feature
operation at station level. It logs all GOOSE
is especially useful when 615 series relays
events during substation operation to enable
without the optional single-line diagram feature
improved system supervision.
are used. The Web HMI of COM600S also
Table 3: Supported ABB solutions
Product Version
Substation Management Unit COM600S 4.0 SP1 or later
4.1 or later (Edition 2)
MicroSCADA Pro SYS 600 9.3 FP2 or later
9.4 or later (Edition 2)
System 800xA 5.1 or later
REM615 13
Product Guide
ABB
MicroSCADA Pro/
System 800xA
Utility: IEC 60870-5-104

Industry: OPC
COM600S COM600S
Web HMI Web HMI
Ethernet switch PCM600 Ethernet switch PCM600
Analog and binary horizontal Analog and binary horizontal

GOOSE communication IEC 61850 GOOSE communication IEC 61850
Figure 7: ABB power system example using Relion relays, COM600S and MicroSCADA Pro/System
800xA
If the amount of available binary inputs or

6. Control outputs of the chosen standard configuration
is not sufficient, the standard configuration can
be modified to release some binary inputs or
REM615 integrates functionality for the control
outputs which have originally been configured
of a circuit breaker via the front panel HMI or
for other purposes, when applicable, or an
by means of remote controls. In addition to the
external input or output module, for example,
circuit breaker control the relay features two
RIO600 can be integrated to the relay. The
control blocks which are intended for motor-
binary inputs and outputs of the external
operated control of disconnectors or circuit
I/O module can be used for the less time
breaker truck and for their position indications.
critical binary signals of the application. The
Further, the relay offers one control block
integration enables releasing of some initially
which is intended for motor-operated control
reserved binary inputs and outputs of the relay
of one earthing switch control and its position
in the standard configuration.
indication.
The suitability of the binary outputs of the
Two physical binary inputs and two physical
relay which have been selected for controlling
binary outputs are needed in the relay for
of primary devices should be carefully verified,
each controllable primary device taken into
for example the make and carry as well as the
use. Depending on the chosen standard
breaking capacity. In case the requirements for
configuration of the relay the number of
the control-circuit of the primary device are not
unused binary inputs and binary outputs varies.
met, the use of external auxiliary relays should
Further, some standard configurations also
to be considered.
offer optional hardware modules that increase
the number of available binary inputs and The optional large graphical LCD of the
outputs. relay's HMI includes a single-line diagram
(SLD) with position indication for the relevant
14 REM615
Product Guide
primary devices. Interlocking schemes required By default, the binary channels are set to record
by the application are configured using the external or internal relay signals, for example,
signal matrix or the application configuration the start or trip signals of the relay stages,
functionality of PCM600. or external blocking or control signals. Binary
relay signals, such as protection start and
The relay is provided with a load profile
trip signals, or an external relay control signal
recorder. The load profile feature stores the
via a binary input, can be set to trigger the
historical load data captured at a periodical
recording. Recorded information is stored in a
time interval (demand interval). The records are
nonvolatile memory and can be uploaded for
in COMTRADE format.
subsequent fault analysis.
7. Measurement
9. Event log
The relay continuously measures the phase
To collect sequence-of-events information,
currents and the neutral current. Furthermore,
the relay has a nonvolatile memory capable
the relay measures the phase voltages and the
of storing 1024 events with the associated
residual voltage. Depending on the standard
time stamps. The non-volatile memory retains
configuration, the relay also offers frequency
its data even if the relay temporarily loses
measurement. In addition, the relay calculates
its auxiliary supply. The event log facilitates
the symmetrical components of the currents
detailed pre- and post-fault analyses of feeder
and voltages, maximum current demand value
faults and disturbances. The considerable
over a user-selectable pre-set time frame, the
capacity to process and store data and
active and reactive power, the power factor
events in the relay facilitates meeting the
and the active and reactive energy values.
growing information demand of future network
Calculated values are also obtained from the
configurations.
protection and condition monitoring functions
of the relay. The sequence-of-events information can be
accessed either via local HMI or remotely via
The measured values can be accessed via the
the communication interface of the relay. The
local HMI or remotely via the communication
information can also be accessed locally or
interface of the relay. The values can also be
remotely using the Web HMI.
accessed locally or remotely using the Web HMI.
The relay is provided with a load profile
recorder. The load profile feature stores the 10. Recorded data
historical load data captured at a periodical
time interval (demand interval). The records are The relay has the capacity to store the records
in COMTRADE format. of the 128 latest fault events. The records can
be used to analyze the power system events.
Each record includes, for example, current,
8. Disturbance recorder voltage and angle values and a time stamp. The
fault recording can be triggered by the start or
The relay is provided with a disturbance the trip signal of a protection block, or by both.
recorder featuring up to 12 analog and 64 The available measurement modes include DFT,
binary signal channels. The analog channels can RMS and peak-to-peak. Fault records store
be set to record either the waveform or the relay measurement values at the moment when
trend of the currents and voltages measured. any protection function starts. In addition, the
maximum demand current with time stamp is
The analog channels can be set to trigger the
separately recorded. The records are stored in
recording function when the measured value
the non-volatile memory.
falls below or exceeds the set values. The binary
signal channels can be set to start a recording
either on the rising or the falling edge of the
binary signal or on both.
REM615 15
Product Guide
IEC 61850-8-1
Process USER LEVEL PROCESS LEVEL
PCM600
IEC 103
Modbus
WHMI
events
DNP3
LHMI
(FIFO) 1024
Fault
records
(FIFO) 128
BASIC FUNCTIONS
Fault summary;
Trip timestamp, Function, Currents, Voltages, etc.
Audit
trail
events
(FIFO) 2048
System and security-related events;

Configuration changes, Control, Login, etc.
Disturbance
records
n…100
Load profile
record
...7 yrs Historical load data captured at a periodical
time interval (Demand interval 1...180min)
Function specific data
Min/max demand currents, Operation counters, etc.

History view
Figure 8: Recording and event capabilities overview
12. Trip-circuit supervision

11. Condition monitoring
The trip-circuit supervision continuously
The condition monitoring functions of the relay monitors the availability and operability of the
constantly monitor the performance and the trip circuit. It provides opencircuit monitoring
condition of the circuit breaker. The monitoring both when the circuit breaker is in its closed
comprises the spring charging time, SF6 gas and in its open position. It also detects loss of
pressure, the travel time and the inactivity time circuit-breaker control voltage.
of the circuit breaker.
The monitoring functions provide operational 13. Self-supervision
circuit breaker history data, which can be
used for scheduling preventive circuit breaker The relay’s built-in self-supervision system
maintenance. continuously monitors the state of the relay
In addition, the relay includes a runtime counter hardware and the operation of the relay
for monitoring of how many hours the motor software. Any fault or malfunction detected is
has been in operation thus enabling scheduling used for alerting the operator.
of time-based preventive maintenance of the A permanent relay fault blocks the protection
motor. functions to prevent incorrect operation.
16 REM615
Product Guide
14. Fuse failure supervision inputs allow connection of either 1 A or 5 A

secondary current transformers. The optional
The relay includes fuse failure supervision residual-current input 0.2/1 A is normally used
functionality. The fuse failure supervision in applications requiring sensitive earth-fault
detects failures between the voltage protection and featuring core-balance current
measurement circuit and the relay. The transformers. The three phasevoltage inputs
failures are detected either by the negative and the residual-voltage input covers the
sequence-based algorithm or by the delta rated voltages 60-210 V. Both phase-to-phase
voltage and delta current algorithm. Upon voltages and phase-to-earth voltages can be
the detection of a failure, the fuse failure connected.
supervision function activates an alarm and The standard configuration D includes one
blocks voltage-dependent protection functions conventional residual current (Io 0.2/1 A)
from unintended operation. input and three sensor inputs for the direct
connection of three combi-sensors with RJ-45
connectors. As an alternative to combi-sensors,
15. Current circuit supervision separate current and voltage sensors can
be utilized using adapters. Furthermore, the
The relay includes current circuit supervision. adapters also enable the use of sensors with
Current circuit supervision is used for detecting Twin-BNC connectors.
faults in the current transformer secondary
circuits. On detecting of a fault the current The rated values of the current and voltage
circuit supervision function activates an alarm inputs are settable parameters of the relay.
LED and blocks certain protection functions to In addition, the binary input thresholds are
avoid unintended operation. The current circuit selectable within the range of 16…176 V DC by
supervision function calculates the sum of the adjusting the relay’s parameter settings.
phase currents from the protection cores and All binary input and output contacts are
compares the sum with the measured single freely configurable with the signal matrix
reference current from a core balance current or application configuration functionality of
transformer or from separate cores in the PCM600.
phase current transformers.
As an option for standard configurations A
and B, the relay offers six RTD inputs and two
16. Access control mA inputs. By means of the optional RTD/mA
module the relay can measure up to eight
To protect the relay from unauthorized access analog signals such as temperature, pressure
and to maintain information integrity, the and tap changer position values via the six RTD
relay is provided with a four-level, role-based inputs or the two mA inputs using transducers.
authentication system with administrator- The values can, apart from measuring and
programmable individual passwords for the monitoring purposes, be used for tripping and
viewer, operator, engineer and administrator alarm purposes using the offered optional
levels. The access control applies to the local multipurpose protection functions.
HMI, the Web HMI and PCM600. Optionally, a binary input and output module
can be selected. It has three high speed binary
outputs (HSO) and it decreases the total
17. Inputs and outputs
operate time with typically 4...6 ms compared
to the normal power outputs.
The relay is equipped with three phase-current
inputs, one residual-current input, three phase- See the Input/output overview table and the
voltage inputs and one residual voltage input. terminal diagrams for more information about
The phase-current inputs and the residual the inputs and outputs.
current inputs are rated 1/5 A, that is, the
REM615 17
Product Guide
Table 4: Input/output overview
Std. conf. Order code digit Analog channels Binary channels
5-6 7-8 CT VT Combi BI BO RTD mA

sensor
A AC / AD AB 4 – – 4 4 PO + 2 SO – –
AD 4 – – 12 4 PO + 6 SO – –
FE 4 – – 12 4 PO + 2 SO + 3 – –
HSO
AG / AH AB 4 – – 4 4 PO + 2 SO 6 2
B CA / CB AH 4 3 – 8 4 PO + 6 SO – –
AJ 4 3 – 14 4 PO + 9 SO – –
FD 4 3 – 8 4 PO + 2 SO + 3 – –
HSO
FF 4 3 – 14 4 PO + 5 SO + 3 – –
HSO
CC / CD AH 4 3 – 8 4 PO + 6 SO 6 2
FD 4 3 – 8 4 PO + 2 SO + 3 6 2
HSO
C AE / AF AG 4 5 – 16 4 PO + 6 SO – –
FC 4 5 – 16 4 PO + 2 SO + 3 – –
HSO
D DA / DB AH 1 – 3 8 4 PO + 6 SO – –
FD 1 – 3 8 4 PO + 2 SO + 3 – –
HSO
The IEC 61850 communication implementation

18. Station communication supports monitoring and control functions.
Additionally, parameter settings, disturbance
recordings and fault records can be accessed
The relay supports a range of communication
using the IEC 61850 protocol. Disturbance
protocols including IEC 61850 Edition 2, IEC
recordings are available to any Ethernet-based
61850-9-2 LE, IEC 60870-5-103, Modbus® and
application in the standard COMTRADE file
DNP3. Profibus DPV1 communication protocol
format. The relay supports simultaneous event
is supported with using the protocol converter
reporting to five different clients on the station
SPA-ZC 302. Operational information and
bus. The relay can exchange data with other
controls are available through these protocols.
devices using the IEC 61850 protocol.
However, some communication functionality,
for example, horizontal communication The relay can send binary and analog signals
between the relays, is only enabled by the IEC to other devices using the IEC 61850-8-1
61850 communication protocol. GOOSE (Generic Object Oriented Substation
Event) profile. Binary GOOSE messaging can,
The IEC 61850 protocol is a core part of the
for example, be employed for protection
relay as the protection and control application
and interlocking-based protection schemes.
is fully based on standard modelling. The relay
The relay meets the GOOSE performance
supports Edition 2 and Edition 1 versions
requirements for tripping applications in
of the standard. With Edition 2 support, the
distribution substations, as defined by the
relay has the latest functionality modelling
IEC 61850 standard (<10 ms data exchange
for substation applications and the best
between the devices). The relay also supports
interoperability for modern substations. It
the sending and receiving of analog values
incorporates also the full support of standard
using GOOSE messaging. Analog GOOSE
device mode functionality supporting different
messaging enables easy transfer of analog
test applications. Control applications can
measurement values over the station bus,
utilize the new safe and advanced station
thus facilitating for example the sending of
control authority feature.
18 REM615
Product Guide
measurement values between the relays when using RSTP in managed switches. Ethernet
controlling parallel running transformers. redundancy can be applied to Ethernet-based
IEC 61850, Modbus and DNP3 protocols.
The relay also supports IEC 61850 process
bus by sending sampled values of analog The IEC 61850 standard specifies network
currents and voltages and by receiving sampled redundancy which improves the system
values of voltages. With this functionality the availability for the substation communication.
galvanic interpanel wiring can be replaced with The network redundancy is based on two
Ethernet communication. The measured values complementary protocols defined in the IEC
are transferred as sampled values using IEC 62439-3 standard: PRP and HSR protocols. Both
61850-9-2 LE protocol. The intended application the protocols are able to overcome a failure
for sampled values shares the voltages to of a link or switch with a zero switch-over
other 615 series relays, having voltage based time. In both the protocols, each network node
functions and 9-2 support. 615 relays with has two identical Ethernet ports dedicated for
process bus based applications use IEEE 1588 one network connection. The protocols rely on
for high accuracy time synchronization. the duplication of all transmitted information
and provide a zero switch-over time if the
For redundant Ethernet communication, the
links or switches fail, thus fulfilling all the
relay offers either two optical or two galvanic
stringent real-time requirements of substation
Ethernet network interfaces. A third port with
automation.
galvanic Ethernet network interface is also
available. The third Ethernet interface provides In PRP, each network node is attached to
connectivity for any other Ethernet device to two independent networks operated in parallel.
an IEC 61850 station bus inside a switchgear The networks are completely separated to
bay, for example connection of a Remote I/O. ensure failure independence and can have
Ethernet network redundancy can be achieved different topologies. The networks operate in
using the high-availability seamless redundancy parallel, thus providing zero-time recovery and
(HSR) protocol or the parallel redundancy continuous checking of redundancy to avoid
protocol (PRP) or a with self-healing ring failures.
COM600
SCADA
Ethernet switch Ethernet switch

IEC 61850 PRP
Figure 9: Parallel redundancy protocol (PRP) solution
HSR applies the PRP principle of parallel sent, the node sends two frames, one through
operation to a single ring. For each message each port. Both the frames circulate in opposite
REM615 19
Product Guide
directions over the ring. Every node forwards the connection of up to 30 relays. If more
the frames it receives from one port to another than 30 relays are to be connected, it is
to reach the next node. When the originating recommended to split the network into several
sender node receives the frame it sent, the rings to guarantee the performance for real-
sender node discards the frame to avoid loops. time applications.
The HSR ring with 615 series relays supports
COM600
Devices not supporting HSR
SCADA
Ethernet switch
Redundancy Redundancy Redundancy

Box Box Box
IEC 61850 HSR
REF615 REF620 RET620 REM620 REF615
Figure 10: High availability seamless redundancy (HSR) solution
The choice between the HSR and PRP relays in the ring topology act as unmanaged
redundancy protocols depends on the required switches forwarding unrelated data traffic. The
functionality, cost and complexity. Ethernet ring solution supports the connection
of up to 30 615 series relays. If more than 30
The self-healing Ethernet ring solution enables
relays are to be connected, it is recommended
a cost-efficient communication ring controlled
to split the network into several rings. The
by a managed switch with standard Rapid
self-healing Ethernet ring solution avoids single
Spanning Tree Protocol (RSTP) support. The
point of failure concerns and improves the
managed switch controls the consistency of the
reliability of the communication.
loop, routes the data and corrects the data flow
in case of a communication switch-over. The
20 REM615
Product Guide
Client A Client B
Network A
Network B
Managed Ethernet switch Managed Ethernet switch

with RSTP support with RSTP support
Figure 11: Self-healing Ethernet ring solution
All communication connectors, except for DNP3 supports both serial and TCP modes for
the front port connector, are placed on connection up to five masters. Changing of the
integrated optional communication modules. active setting and reading fault records are
The relay can be connected to Ethernet- supported. DNP serial and DNP TCP can be used
based communication systems via the RJ-45 in parallel. If required, both IEC 61850 and DNP
connector (100Base-TX) or the fiber optic LC protocols can be run simultaneously.
connector (100Base-FX). If connection to serial
615 series supports Profibus DPV1 with support
bus is required, the 9-pin RS-485 screw-terminal
of SPA-ZC 302 Profibus adapter. If Profibus
can be used. An optional serial interface is
is required the relay must be ordered with
available for RS-232 communication.
Modbus serial options. Modbus implementation
Modbus implementation supports RTU, ASCII includes SPA-protocol emulation functionality.
and TCP modes. Besides standard Modbus This functionality enables connection to SPA-ZC
functionality, the relay supports retrieval of 302.
time-stamped events, changing the active
When the relay uses the RS-485 bus for the
setting group and uploading of the latest
serial communication, both two- and four wire
fault records. If a Modbus TCP connection is
connections are supported. Termination and
used, five clients can be connected to the
pull-up/down resistors can be configured with
relay simultaneously. Further, Modbus serial
jumpers on the communication card so external
and Modbus TCP can be used in parallel, and if
resistors are not needed.
required both IEC 61850 and Modbus protocols
can be run simultaneously. The relay supports the following time
synchronization methods with a time-stamping
The IEC 60870-5-103 implementation supports
resolution of 1 ms.
two parallel serial bus connections to two
different masters. Besides basic standard Ethernet-based
functionality, the relay supports changing of
• SNTP (Simple Network Time Protocol)
the active setting group and uploading of
disturbance recordings in IEC 60870-5-103 With special time synchronization wiring
format. Further, IEC 60870-5-103 can be used
at the same time with the IEC 61850 protocol.
REM615 21
Product Guide
• IRIG-B (Inter-Range Instrumentation Group - • Receive (slave): 1-step/2-step

Time Code Format B) • Transmit (master): 1-step
The relay supports the following high accuracy • Layer 2 mapping
time synchronization method with a time- • Peer to peer delay calculation
stamping resolution of 4 μs required especially • Multicast operation
in process bus applications.
Required accuracy of grandmaster clock is +/-1
• PTP (IEEE 1588) v2 with Power Profile μs. The relay can work as a master clock per
BMC algorithm if the external grandmaster
The IEEE 1588 support is included in all variants
clock is not available for short term.
having a redundant Ethernet communication
module. The IEEE 1588 support is included in all variants
having a redundant Ethernet communication
IEEE 1588 v2 features
module.
• Ordinary Clock with Best Master Clock
In addition, the relay supports time
algorithm
synchronization via Modbus, DNP3 and IEC
• One-step Transparent Clock for Ethernet 60870-5-103 serial communication protocols.
ring topology
• 1588 v2 Power Profile
Table 5: Supported station communication interfaces and protocols
Interfaces/Protocols Ethernet Serial
100BASE-TX RJ-45 100BASE-FX LC RS-232/RS-485 Fiber optic ST

IEC 61850-8-1 ● ● - -
IEC 61850-9-2 LE ● ● - -
MODBUS RTU/ASCII - - ● ●
MODBUS TCP/IP ● ● - -
DNP3 (serial) - - ● ●
DNP3 TCP/IP ● ● - -
IEC 60870-5-103 - - ● ●
● = Supported
19. Technical data
19.1 Dimensions
Table 6: Dimensions
Description Value
Width Frame 177 mm
Case 164 mm
Height Frame 177 mm (4U)
Case 160 mm
Depth 201 mm (153 + 48 mm)
Weight Complete protection relay 4.1 kg
Plug-in unit only 2.1 kg
22 REM615
Product Guide
19.2 Power supply
Table 7: Power supply
Description Type 1 Type 2

Nominal auxiliary voltage U n 100, 110, 120, 220, 240 V AC, 50 and 60 Hz 24, 30, 48, 60 V DC
48, 60, 110, 125, 220, 250 V DC
Maximum interruption time in the auxili- 50 ms at U n
ary DC voltage without resetting the re-
lay
Auxiliary voltage variation 38...110% of U n (38...264 V AC) 50...120% of U n (12...72 V DC)
80...120% of U n (38.4...300 V DC)
Start-up threshold 19.2 V DC (24 V DC × 80%)
Burden of auxiliary voltage supply under DC <13.0 W (nominal)/<18.0 W (max.) DC <13.0 W (nominal)/<18.0 W (max.)
quiescent (P q)/operating condition
AC <16.0 W (nominal)/<21.0 W (max.)
Ripple in the DC auxiliary voltage Max 15% of the DC value (at frequency of 100 Hz)
Fuse type T4A/250 V
19.3 Energizing inputs
Table 8: Energizing inputs
Description Value
Rated frequency 50/60 Hz
Current inputs Rated current, I n 0.2/1 A 1 1/5 A 2
Thermal withstand capability:
• Continuously 4A 20 A
• For 1 s 100 A 500 A
Dynamic current withstand:
• Half-wave value 250 A 1250 A
Input impedance <100 mΩ <20 mΩ

Voltage inputs Rated voltage 60...210 V AC
Voltage withstand:
• Continuous 240 V AC
• For 10 s 360 V AC
Burden at rated voltage <0.05 VA
1 Ordering option for residual current input

2 Residual current and/or phase current
REM615 23
Product Guide
19.4 Energizing inputs (sensors)
Table 9: Energizing Inputs (SIM0002)
Description Value
Current sensor input Rated current voltage 75 mV ... 9000 mV 1
Continuous voltage withstand 125 V
Input impedance at 50/60Hz 2...3 MΩ 2
Voltage sensor input Rated secondary voltage 346 mV…1733 mV 3
Input impedance at 50/60Hz 3 MΩ
Table 10: Energizing Inputs (SIM0005)
Description Value
Current sensor input Rated current voltage 75 mV ... 9000 mV 1
Voltage sensor input Rated secondary voltage 346 mV…2339 mV 4
19.5 Binary inputs
Table 11: Binary inputs
Description Value
Operating range ±20% of the rated voltage
Rated voltage 24...250 V DC
Current drain 1.6...1.9 mA

Power consumption 31.0...570.0 mW
Threshold voltage 16...176 V DC
Reaction time <3 ms
1 Equals the current range of 40 … 4000 A with 80A, 3mV/Hz Rogowski

2 Depending on the used nominal current (hardware gain)
3 Covers 6 kV … 30 kV sensors with division ratio of 10 000:1. Secondary voltages 600mV/√3 … 3
V / √3. Range up to 2 x Rated.
4 Covers 6 kV … 40.5 kV sensors with division ratio of 10 000:1. Secondary voltages 600mV/√3 …
4.05V / √3. Range up to 2 x Rated.
24 REM615
Product Guide
19.6 RTD/mA measurement (XRGGIO130)
Table 12: RTD/mA measurement (XRGGIO130)
Description Value
RTD inputs Supported RTD sensors 100 Ω platinum TCR 0.00385 (DIN 43760)
250 Ω platinum TCR 0.00385
100 Ω nickel TCR 0.00618 (DIN 43760)
120 Ω nickel TCR 0.00618
10 Ω copper TCR 0.00427
Supported resistance range 0...2 kΩ

Maximum lead resistance
(three-wire measurement) 25 Ω per lead
Isolation 2 kV (inputs to protective earth)
Response time <4 s

RTD/resistance sensing cur-
rent Maximum 0.33 mA rms
Operation accuracy Resistance Temperature
± 2.0% or ±1 Ω ±1°C
10 Ω copper: ±2°C
mA inputs Supported current range 0…20 mA

Current input impedance 44 Ω ± 0.1%
Operation accuracy ±0.5% or ±0.01 mA
19.7 Signal outputs
Table 13: Signal output X100: SO1
Description Value
Rated voltage 250 V AC/DC
Continuous contact carry 5A
Make and carry for 3.0 s 15 A
Breaking capacity when the control-circuit time constant L/ 1 A/0.25 A/0.15 A
R<40 ms, at 48/110/220 V DC
Minimum contact load 100 mA at 24 V AC/DC
Table 14: Signal outputs and IRF output
Description Value
Make and carry 0.5 s 15 A
Breaking capacity when the control-circuit time constant L/ 1 A/0.25 A/0.15 A
R<40 ms, at 48/110/220 V DC
REM615 25
Product Guide
19.8 Double-pole power output relays with TCS function
Table 15: Double-pole power output relays with TCS function
Description Value
Breaking capacity when the control-circuit time con- 5 A/3 A/1 A
stant L/R<40 ms, at 48/110/220 V DC (two contacts
connected in series)
Trip-circuit supervision (TCS):
• Control voltage range 20...250 V AC/DC
• Current drain through the supervision circuit ~1.5 mA
• Minimum voltage over the TCS contact 20 V AC/DC (15...20 V)
19.9 Single-pole power output relays
Table 16: Single-pole power output relays
Description Value
Breaking capacity when the control-circuit time constant L/ 5 A/3 A/1 A
R<40 ms, at 48/110/220 V DC
19.10 High-speed output HSO with BIO0007
Table 17: High-speed output HSO with BIO0007
Description Value
Breaking capacity when the control-circuit time con- 5 A/3 A/1 A
stant L/R <40 ms, at 48/110/220 V DC
26 REM615
Product Guide
Description Value
Operate time <1 ms
Reset <20 ms, resistive load
19.11 Front port Ethernet interfaces
Table 18: Front port Ethernet interfaces
Ethernet interface Protocol Cable Data transfer rate

Front TCP/IP protocol Standard Ethernet CAT 5 cable with RJ-45 con- 10 MBits/s
nector
19.12 Station communication link, fiber optic
Table 19: Station communication link, fiber optic
Connector Fiber type1 Wave length Typical max. Permitted path

length2 attenuation3
LC MM 62.5/125 or 50/125 μm glass fiber 1300 nm 2 km <8 dB
core
ST MM 62.5/125 or 50/125 μm glass fiber 820...900 nm 1 km <11 dB
core
19.13 IRIG-B
Table 20: IRIG-B
Description Value
IRIG time code format B004, B005 4
Isolation 500V 1 min
Modulation Unmodulated
Logic level 5 V TTL
Current consumption <4 mA
Power consumption <20 mW
1 (MM) multi-mode fiber, (SM) single-mode fiber

2 Maximum length depends on the cable attenuation and quality, the amount of splices and
connectors in the path.
3 Maximum allowed attenuation caused by connectors and cable together
4 According to the 200-04 IRIG standard
REM615 27
Product Guide
19.14 Lens sensor and optical fiber for arc protection
Table 21: Lens sensor and optical fiber for arc protection
Description Value
Fiber optic cable including lens 1.5 m, 3.0 m or 5.0 m
Normal service temperature range of the lens -40...+100°C
Maximum service temperature range of the lens, max 1 +140°C
h
Minimum permissible bending radius of the connection 100 mm
fiber
19.15 Degree of protection of flush-mounted protection relay
Table 22: Degree of protection of flush-mounted protection relay
Description Value
Front side IP 54
Rear side, connection terminals IP 20
19.16 Environmental conditions
Table 23: Environmental conditions
Description Value
Operating temperature range -25...+55ºC (continuous)
Short-time service temperature range -40...+85ºC (<16 h)5, 6
Relative humidity <93%, non-condensing
Atmospheric pressure 86...106 kPa
Altitude Up to 2000 m
Transport and storage temperature range -40...+85ºC
19.17 Electromagnetic compatibility tests
Table 24: Electromagnetic compatibility tests
Description Type test value Reference

1 MHz/100 kHz burst disturbance test IEC 61000-4-18
IEC 60255-26, class III
IEEE C37.90.1-2002
• Common mode 2.5 kV
5 Degradation in MTBF and HMI performance outside the temperature range of -25...+55 ºC
6 For relays with an LC communication interface the maximum operating temperature is +70 ºC
28 REM615
Product Guide
• Differential mode 2.5 kV
3 MHz, 10 MHz and 30 MHz burst disturb- IEC 61000-4-18

ance test
IEC 60255-26, class III
• Common mode 2.5 kV
Electrostatic discharge test IEC 61000-4-2

IEC 60255-26
IEEE C37.90.3-2001
• Contact discharge 8 kV
• Air discharge 15 kV
Radio frequency interference test
10 V (rms) IEC 61000-4-6

f = 150 kHz...80 MHz IEC 60255-26, class III
10 V/m (rms) IEC 61000-4-3

f = 80...2700 MHz IEC 60255-26, class III
10 V/m ENV 50204

f = 900 MHz IEC 60255-26, class III
20 V/m (rms) IEEE C37.90.2-2004

f = 80...1000 MHz
Fast transient disturbance test IEC 61000-4-4

IEC 60255-26
IEEE C37.90.1-2002
• All ports 4 kV
Surge immunity test IEC 61000-4-5

IEC 60255-26
• Communication 1 kV, line-to-earth
• Other ports 4 kV, line-to-earth

2 kV, line-to-line
Power frequency (50 Hz) magnetic field IEC 61000-4-8

immunity test
• Continuous 300 A/m

• 1...3 s 1000 A/m
Pulse magnetic field immunity test 1000 A/m IEC 61000-4-9
6.4/16 µs
Damped oscillatory magnetic field im- IEC 61000-4-10

munity test
• 2s 100 A/m
• 1 MHz 400 transients/s
REM615 29
Product Guide

Voltage dips and short interruptions 30%/10 ms IEC 61000-4-11
60%/100 ms
60%/1000 ms
>95%/5000 ms
Power frequency immunity test Binary inputs only IEC 61000-4-16

IEC 60255-26, class A
• Common mode 300 V rms
• Differential mode 150 V rms
Conducted common mode disturbances 15 Hz...150 kHz IEC 61000-4-16
Test level 3 (10/1/10 V rms)
Emission tests EN 55011, class A

IEC 60255-26
CISPR 11
CISPR 12
• Conducted
0.15...0.50 MHz <79 dB (µV) quasi peak

<66 dB (µV) average
0.5...30 MHz <73 dB (µV) quasi peak

<60 dB (µV) average
• Radiated
30...230 MHz <40 dB (µV/m) quasi peak, measured at

10 m distance
230...1000 MHz <47 dB (µV/m) quasi peak, measured at

10 m distance
1…3 GHz <76 dB (µV/m) peak

<56 dB (µV/m) average, measured at 3 m
distance
3…6 GHz <80 dB (µV/m) peak

<60 dB (µV/m) average, measured at 3 m
distance
19.18 Insulation tests
Table 25: Insulation tests

Dielectric tests 2 kV, 50 Hz, 1 min IEC 60255-27
500 V, 50 Hz, 1 min, communication
820 V, 50 Hz, 1 min, sensor inputs of SIM0005 IEC 61869-6

30 REM615
Product Guide

Impulse voltage test 5 kV, 1.2/50 μs, 0.5 J IEC 60255-27
1 kV, 1.2/50 μs, 0.5 J, communication
1,5 kV, 1,2/50 µs, 0,5 J, sensor inputs of SIM0005 IEC 61869-6
Insulation resistance measurements >100 M Ω, 500 V DC IEC 60255-27
Protective bonding resistance <0.1 Ω, 4 A, 60 s IEC 60255-27
19.19 Mechanical tests
Table 26: Mechanical tests
Description Requirement Reference

Vibration tests (sinusoidal) Class 2 IEC 60068-2-6 (test Fc)
IEC 60255-21-1
Shock and bump test Class 2 IEC 60068-2-27 (test Ea shock)

IEC 60068-2-29 (test Eb bump)
IEC 60255-21-2
Seismic test Class 2 IEC 60255-21-3
19.20 Environmental tests
Table 27: Environmental tests

Dry heat test • 96 h at +55ºC IEC 60068-2-2
• 16 h at +85ºC 7
Dry cold test • 96 h at -25ºC IEC 60068-2-1

• 16 h at -40ºC
Damp heat test • 6 cycles (12 h + 12 h) at +25°C…+55°C, humidity IEC 60068-2-30

>93%
Change of temperature test • 5 cycles (3 h + 3 h) at -25°C...+55°C IEC60068-2-14
Storage test • 96 h at -40ºC IEC 60068-2-1

• 96 h at +85ºC IEC 60068-2-2
19.21 Product safety
7 For relays with an LC communication interface the maximum operating temperature is +70 oC
REM615 31
Product Guide
Table 28: Product safety
Description Reference
LV directive 2014/35/EU
Standard EN / BS EN 60255-27
EN / BS EN 60255-1
19.22 EMC compliance
Table 29: EMC compliance
Description Reference
EMC directive 2014/30/EU
Standard EN / BS EN 60255-26
19.23 RoHS compliance
Table 30: RoHS compliance
Description
RoHS Directive 2011/65/EU
19.24 Protection functions
19.24.1 Three-phase non-directional overcurrent protection (PHxPTOC)
Table 31: Three-phase non-directional overcurrent protection (PHxPTOC)
Characteristic Value
Operation accuracy Depending on the frequency of the measured current: f n ±2 Hz
PHLPTOC ±1.5% of the set value or ±0.002 × I n
PHHPTOC8 ±1.5% of set value or ±0.002 × I n

and (at currents in the range of 0.1…10 × I n)
PHIPTOC ±5.0% of the set value
(at currents in the range of 10…40 × I n)
8 Not included in REM615
32 REM615
Product Guide
Start time PHIPTOC: Minimum Typical Maximum

9, 10
I Fault = 2 × set Start
16 ms 19 ms 23 ms
value
I Fault = 10 × set Start 11 ms 12 ms 14 ms
value
PHHPTOC8 and
PHLPTOC: 23 ms 26 ms 29 ms
value
Reset time Typically 40 ms
Reset ratio Typically 0.96
Retardation time <40 ms
Operate time accuracy in definite time ±1.0% of the set value or ±20 ms
mode
Operate time accuracy in inverse time mode ±5.0% of the theoretical value or ±20 ms11
Suppression of harmonics RMS: No suppression

DFT: -50 dB at f = n × f n, where n = 2, 3, 4, 5,…
Peak-to-Peak: No suppression
P-to-P+backup: No suppression
19.24.2 Three-phase non-directional overcurrent protection (PHxPTOC) main settings
Table 32: Three-phase non-directional overcurrent protection (PHxPTOC) main settings
Parameter Function Value (Range) Step

Start value PHLPTOC 0.05...5.00 × I n 0.01
PHHPTOC12 0.10...40.00 × I n 0.01
PHIPTOC 1.00...40.00 × I n 0.01
Time multiplier PHLPTOC and PHHPTOC12 0.05...15.00 0.01
PHLPTOC and PHHPTOC12 40...200000 ms 10
9 Set Operate delay time = 0,02 s, Operate curve type = IEC definite time, Measurement mode
= default (depends on stage), current before fault = 0.0 × In, fn = 50 Hz, fault current in one
phase with nominal frequency injected from random phase angle, results based on statistical
distribution of 1000 measurements
10 Includes the delay of the signal output contact
11 Includes the delay of the heavy-duty output contact
12 Not included in this product
REM615 33
Product Guide

PHIPTOC 20...200000 ms 10
Operating curve type13 PHLPTOC Definite or inverse time
Curve type: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 17,
18, 19
PHHPTOC12 Definite or inverse time

Curve type: 1, 3, 5, 9, 10, 12, 15, 17
PHIPTOC Definite time
19.24.3 Non-directional earth-fault protection (EFxPTOC)
Table 33: Non-directional earth-fault protection (EFxPTOC)
EFLPTOC ±1.5% of the set value or ±0.002 × I n
EFHPTOC ±1.5% of set value or ±0.002 × I n

and (at currents in the range of 0.1…10 × I n)
EFIPTOC14 ±5.0% of the set value
Start time 15, 16 Minimum Typical Maximum
EFIPTOC14:
16 ms 19 ms 23 ms
11 ms 14 ms
value
value
EFHPTOC and EFLP-

23 ms 26 ms 29 ms
TOC:
value
mode
13 For further reference, see the Operation characteristics table

15 Measurement mode = default (depends on stage), current before fault = 0.0 × I n, f n = 50 Hz,
earth-fault current with nominal frequency injected from random phase angle, results based on
statistical distribution of 1000 measurements
34 REM615
Product Guide
Operate time accuracy in inverse time mode ±5.0% of the theoretical value or ±20 ms 17

19.24.4 Non-directional earth-fault protection (EFxPTOC) main settings
Table 34: Non-directional earth-fault protection (EFxPTOC) main settings

Start value EFLPTOC 0.010. 5.000 × In 0.005
EFHPTOC 0.10. 40.00 × In 0.01
EFIPTOC 18 1.00. 40.00 × In 0.01
Time multiplier EFLPTOC and EFHPTOC 0.05...15.00 0.01
Operate delay time EFLPTOC and EFHPTOC 40...200000 ms 10
EFIPTOC18 20...200000 ms 10
Operating curve type19 EFLPTOC Definite or inverse time
Curve type: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 17, 18, 19"
EFHPTOC Definite or inverse time

Curve type: 1, 3, 5, 9, 10, 12, 15, 17"
EFIPTOC18 Definite time
19.24.5 Directional earth-fault protection (DEFxPDEF)
Table 35: Directional earth-fault protection (DEFxPDEF)
DEFLPDEF Current:
±1.5% of the set value or ±0.002 × I n
Voltage
±1.5% of the set value or ±0.002 × U n
Phase angle:
±2°
17 Maximum Start value = 2.5 × I n, Start value multiples in range of 1.5...20

18 Not included in this product
REM615 35
Product Guide
DEFHPDEF20 Current:
(at currents in the range of 0.1…10 × I n)
±5.0% of the set value
Voltage:
Phase angle:
±2°
DEFHPDEF20
42 46 ms 49 ms
value
DEFLPDEF
58 ms 62 ms 66 ms
value
mode


21 Set Operate delay time = 0.06 s, Operate curve type = IEC definite time, Measurement mode =
default (depends on stage), current before fault = 0.0 × I n, f n = 50 Hz, earth-fault current with
nominal frequency injected from random phase angle, results based on statistical distribution of
1000 measurements
23 Maximum Start value = 2.5 × I n, Start value multiples in range of 1.5...20
36 REM615
Product Guide
19.24.6 Directional earth-fault protection (DEFxPDEF) main settings
Table 36: Directional earth-fault protection (DEFxPDEF) main settings

Start value DEFLPDEF 0.010...5.000 × I n 0.005
DEFHPDEF24 0.10...40.00 × I n 0.01
Directional mode DEFLPDEF and DEFHPDEF 1 = Non-directional -
2 = Forward
3 = Reverse
Time multiplier DEFLPDEF 0.05...15.00 0.01

DEFHPDEF24 0.05...15.00 0.01
Operate delay time DEFLPDEF 50...200000 ms 10
DEFHPDEF24 40...200000 ms 10
Operating curve type 25 DEFLPDEF Definite or inverse time
Curve type: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 17,
18, 19
DEFHPDEF24 Definite or inverse time

Curve type: 1, 3, 5, 15, 17
Operation mode DEFxPDEF 1 = Phase angle -
2 = IoSin
3 = IoCos
4 = Phase angle 80
5 = Phase angle 88
19.24.7 Three-phase undervoltage protection (PHPTUV)
Table 37: Three-phase undervoltage protection (PHPTUV)
Operation accuracy Depending on the frequency of the voltage measured: f n ±2
Hz
U Fault = 0.9 × set Start value 62 ms 66 ms 70 ms

Reset ratio Depends on the set Relative hysteresis

25 For further reference, see the Operating characteristics table
26 Start value = 1.0 × U n, Voltage before fault = 1.1 × U n, f n = 50 Hz, undervoltage in one phase-to-
phase with nominal frequency injected from random phase angle, results based on statistical
REM615 37
Product Guide
Operate time accuracy in definite time mode ±1.0% of the set value or ±20 ms
Suppression of harmonics DFT: -50 dB at f = n × f n, where n = 2, 3, 4, 5,…
19.24.8 Three-phase undervoltage protection (PHPTUV) main settings
Table 38: Three-phase undervoltage protection (PHPTUV) main settings
Start value PHPTUV 0.05. 1.20 × U n 0.01
Time multiplier PHPTUV 0.05...15.00 0.01
Operate delay time PHPTUV 60...300000 ms 10
Operating curve type29 PHPTUV Definite or inverse time Curve type: 5, 15, 21, 22, 23
19.24.9 Positive-sequence undervoltage protection (PSPTUV)
Table 39: Positive-sequence undervoltage protection (PSPTUV)
Operation accuracy Depending on the frequency of the measured voltage: f n ±2
Hz


Reset ratio Depends on the set Relative hysteresis
28 Minimum Start value = 0.50, Start value multiples in range of 0.90...0.20

30 Start value = 1.0 × U n, positive-sequence voltage before fault = 1.1 × U n, f n = 50 Hz, positive
sequence undervoltage with nominal frequency injected from random phase angle, results based
on statistical distribution of 1000 measurements
38 REM615
Product Guide
19.24.10 Positive-sequence undervoltage protection (PSPTUV) main settings
Table 40: Positive-sequence undervoltage protection (PSPTUV) main settings

Start value PSPTUV 0.010...1.200 × U n 0.001
Operate delay time PSPTUV 40...120000 ms 10
Voltage block value PSPTUV 0.01...1.00 × U n 0.01
19.24.11 Negative-sequence overvoltage protection (NSPTOV)
Table 41: Negative-sequence overvoltage protection (NSPTOV)
Operation accuracy Depending on the frequency of the voltage measured: f n


19.24.12 Negative-sequence overvoltage protection (NSPTOV) main settings
Table 42: Negative-sequence overvoltage protection (NSPTOV) main settings

Start value NSPTOV 0.010...1.000 × U n 0.001
Operate delay time NSPTOV 40...120000 ms 1
19.24.13 Frequency protection (FRPFRQ)
Table 43: Frequency protection (FRPFRQ)
Operation accuracy f>/f< ±5 mHz
df/dt ±50 mHz/s (in range |df/dt| <5 Hz/s)

±2.0% of the set value (in range 5 Hz/s < |df/dt| < 15 Hz/s)
32 Negative-sequence voltage before fault = 0.0 × U n, f n = 50 Hz, negative-sequence overvoltage

with nominal frequency injected from random phase angle, results based on statistical distribu-
tion of 1000 measurements
REM615 39
Product Guide
Start time f>/f< <80 ms
df/dt <120 ms
Reset time <150 ms
Operate time accuracy ±1.0% of the set value or ±30 ms
19.24.14 Frequency protection (FRPFRQ) main settings
Table 44: Frequency protection (FRPFRQ) main settings

Operation mode FRPFRQ 1 = Freq< -
2 = Freq>
3 = df/dt
4 = Freq< + df/dt
5 = Freq> + df/dt
6 = Freq< OR df/dt
7 = Freq> OR df/dt
Start value Freq> FRPFRQ 0.9000...1.2000 × f n 0.0001

Start value Freq< FRPFRQ 0.8000...1.1000 × f n 0.0001
Start value df/dt FRPFRQ -0.2000...0.2000 × f n/s 0.005
Operate Tm Freq FRPFRQ 80...200000 ms 10
Operate Tm df/dt FRPFRQ 120...200000 ms 10
19.24.15 Negative-sequence overcurrent protection for machines (MNSPTOC)
Table 45: Negative-sequence overcurrent protection for machines (MNSPTOC)
Operation accuracy Depending on the frequency of the measured current: f n
I Fault = 2.0 × set Start value 23 25 ms 28 ms

34 Negative-sequence current before = 0.0, f n = 50 Hz, results based on statistical distribution of

1000 measurements
36 Start value multiples in range of 1.10...5.00
40 REM615
Product Guide
19.24.16 Negative-sequence overcurrent protection for machines (MNSPTOC) main settings
Table 46: Negative-sequence overcurrent protection for machines (MNSPTOC) main settings

Start value MNSPTOC 0.01...0.50 × I n 0.01
Operating curve type MNSPTOC Definite or inverse time
Curve type: 5, 15, 17, 18
Operate delay time MNSPTOC 100...120000 ms 10

Operation MNSPTOC 1 = on -
5 = off
Cooling time MNSPTOC 5...7200 s 1
19.24.17 Loss of load supervision (LOFLPTUC)
Table 47: Loss of load supervision (LOFLPTUC)
Start time Typically 300 ms
19.24.18 Loss of load supervision (LOFLPTUC) main settings
Table 48: Loss of load supervision (LOFLPTUC) main settings

Start value low LOFLPTUC 0.01...0.50 × I n 0.01
Start value high LOFLPTUC 0.01...1.00 × I n 0.01
Operate delay time LOFLPTUC 400...600000 ms 10
Operation LOFLPTUC 1 = on -
5 = off
19.24.19 Motor load jam protection (JAMPTOC)
Table 49: Motor load jam protection (JAMPTOC)
Operation accuracy Depending on the frequency of the measured current: f n ±2
Hz
REM615 41
Product Guide
19.24.20 Motor load jam protection (JAMPTOC) main settings
Table 50: Motor load jam protection (JAMPTOC) main settings

Operation JAMPTOC 1 = on -
5 = off
Start value JAMPTOC 0.10...10.00 × I n 0.01

Operate delay time JAMPTOC 100...120000 ms 10
19.24.21 Motor start-up supervision (STTPMSU)
Table 51: Motor start-up supervision (STTPMSU)
Hz
Fault = 1.1 × set Start detection 27 ms 30 ms 34 ms

A

19.24.22 Motor start-up supervision (STTPMSU) main settings
Table 52: Motor start-up supervision (STTPMSU) main settings

Motor start-up A STTPMSU 1.0...10.0 × I n 0.1
Motor start-up time STTPMSU 1...80 s 1
Lock rotor time STTPMSU 2...120 s 1
Operation STTPMSU 1 = on -
5 = off
37 Current before = 0.0 × I n, f n = 50 Hz, overcurrent in one phase, results based on statistical
42 REM615
Product Guide

Operation mode STTPMSU 1 = IIt -
2 = IIt, CB
3 = IIt + stall
4 = IIt + stall, CB
Restart inhibit time STTPMSU 0...250 min 1
19.24.23 Phase reversal protection (PREVPTOC)
Table 53: Phase reversal protection (PREVPTOC)
Hz
I Fault = 2.0 × set Start value 23 ms 25 ms 28 ms

19.24.24 Phase reversal protection (PREVPTOC) main settings
Table 54: Phase reversal protection (PREVPTOC) main settings

Start value PREVPTOC 0.05...1.00 x I n 0.01
Operate delay time PREVPTOC 100...60000 ms 10
Operation PREVPTOC 1 = on -
5 = off
39 Negative-sequence current before = 0.0, f n = 50 Hz, results based on statistical distribution of

1000 measurements
REM615 43
Product Guide
19.24.25 Thermal overload protection for motors (MPTTR)
Table 55: Thermal overload protection for motors (MPTTR)
Current measurement: ±1.5% of the set value or ±0.002 × I n
(at currents in the range of 0.01...4.00 × I n)
Operate time accuracy 41 ±2.0% of the theoretical value or ±0.50 s
19.24.26 Thermal overload protection for motors (MPTTR) main settings
Table 56: Thermal overload protection for motors (MPTTR) main settings

Overload factor MPTTR 1.00...1.20 0.01
Alarm thermal value MPTTR 50.0...100.0% 0.1
Restart thermal Val MPTTR 20.0...80.0% 0.1
Weighting factor p MPTTR 20.0...100.0% 0.1
Time constant normal MPTTR 80...4000 s 1
Time constant start MPTTR 80...4000 s 1
Env temperature mode MPTTR 1 = FLC Only -
2 = Use input
3 = Set Amb Temp
Env temperature Set MPTTR -20.0...70.0°C 0.1

Operation MPTTR 1 = on -
5 = off
19.24.27 Circuit breaker failure protection (CCBRBRF)
Table 57: Circuit breaker failure protection (CCBRBRF)
Hz
41 Overload current > 1.2 × Operate level temperature
44 REM615
Product Guide
19.24.28 Circuit breaker failure protection (CCBRBRF) main settings
Table 58: Circuit breaker failure protection (CCBRBRF) main settings

Current value CCBRBRF 0.05...2.00 × I n 0.05
Current value Res CCBRBRF 0.05...2.00 × I n 0.05
CB failure mode CCBRBRF 1 = Current -
2 = Breaker status
3 = Both
CB fail trip mode CCBRBRF 1 = Off -
2 = Without check
3 = Current check
Retrip time CCBRBRF 0...60000 ms 10

CB failure delay CCBRBRF 0...60000 ms 10
CB fault delay CCBRBRF 0...60000 ms 10
19.24.29 Arc protection (ARCSARC)
Table 59: Arc protection (ARCSARC)
Operation accuracy ±3% of the set value or ±0.01 × I n
Operate time Minimum Typical Maximum
Operation mode = "Light+cur- 9 ms 12 ms44 15 ms44

rent" 44 6 ms45 9 ms45
42, 43
4 ms
45
Operation mode = "Light only" 9 ms44 10 ms44 12 ms44

43
4 ms45 6 ms45 7 ms45

42 Phase start value = 1.0 × I n, current before fault = 2.0 × set Phase start value, f n = 50 Hz, fault
with nominal frequency, results based on statistical distribution of 200 measurements
43 Includes the delay of the heavy-duty output contact
44 Normal power output
45 High-speed output
REM615 45
Product Guide
19.24.30 Arc protection (ARCSARC) main settings
Table 60: Arc protection (ARCSARC) main settings

Phase start value ARCSARC 0.50...40.00 × I n 0.01
Ground start value ARCSARC 0.05...8.00 × I n 0.01
Operation mode ARCSARC 1 = Light+current -
2 = Light only
3 = BI controlled
19.24.31 Multipurpose protection (MAPGAPC)
Table 61: Multipurpose protection (MAPGAPC)
Operation accuracy ±1.0% of the set value or ±20 ms
19.24.32 Multipurpose protection (MAPGAPC) main settings
Table 62: Multipurpose protection (MAPGAPC) main settings

Start value MAPGAPC -10000.0...10000.0 0.1
Operate delay time MAPGAPC 0...200000 ms 100
Operation mode MAPGAPC 1 = Over -
2 = Under
19.25 Control functions
19.25.1 Emergency start-up (ESMGAPC)
Table 63: Emergency start-up (ESMGAPC)
Operation accuracy At the frequency f = f n
46 REM615
Product Guide
19.25.2 Emergency start-up (ESMGAPC) main settings
Table 64: Emergency start-up (ESMGAPC) main settings

Motor stand still A ESMGAPC 0.05...0.20 × I n 0.01
Operation ESMGAPC 1 = on -
5 = off
19.26 Condition and supervision functions
19.26.1 Circuit-breaker condition monitoring (SSCBR)
Table 65: Circuit-breaker condition monitoring (SSCBR)
Current measuring accuracy ±1.5% or ±0.002 × I n
(at currents in the range of 0.1…10 × I n)
±5.0%
Travelling time measurement +10 ms / -0 ms
19.26.2 Current circuit supervision (CCSPVC)
Table 66: Current circuit supervision (CCSPVC)
Operate time 46 <30 ms
19.26.3 Current circuit supervision (CCSPVC) main settings
Table 67: Current circuit supervision (CCSPVC) main settings

Start value CCSPVC 0.05...0.20 × I n 0.01
Max operate current CCSPVC 1.00...5.00 × I n 0.01
46 Including the delay of the output contact
REM615 47
Product Guide
19.26.4 Fuse failure supervision (SEQSPVC)
Table 68: Fuse failure supervision (SEQSPVC)
Operate time 47 NPS function U Fault = 1.1 × set Neg Seq volt- <33 ms
age Lev
U Fault = 5.0 × set Neg Seq volt- <18 ms

age Lev
Delta function ΔU = 1.1 × set Voltage change <30 ms

rate
ΔU = 2.0 × set Voltage change <24 ms

rate
19.26.5 Runtime counter for machines and devices (MDSOPT)
Table 69: Runtime counter for machines and devices (MDSOPT)
Description Value
Motor runtime measurement accuracy48 ±0.5%
19.27 Measurement functions
19.27.1 Three-phase current measurement (CMMXU)
Table 70: Three-phase current measurement (CMMXU)

Hz
±0.5% or ±0.002 × I n
(at currents in the range of 0.01...4.00 × I n)
RMS: No suppression
47 Includes the delay of the signal output contact, f n = 50 Hz, fault voltage with nominal frequency
injected from random phase angle, results based on statistical distribution of 1000 measure-
ments
48 Of the reading, for a stand-alone relay, without time synchronization
48 REM615
Product Guide
19.27.2 Sequence current measurement (CSMSQI)
Table 71: Sequence current measurement (CSMSQI)
Operation accuracy Depending on the frequency of the measured current: f/f n =
±2 Hz
±1.0% or ±0.002 × I n
at currents in the range of 0.01...4.00 × I n
19.27.3 Residual current measurement (RESCMMXU)
Table 72: Residual current measurement (RESCMMXU)
Operation accuracy Depending on the frequency of the current measured: f/f n =
±2 Hz
±0.5% or ±0.002 × I n
at currents in the range of 0.01...4.00 × I n

RMS: No suppression
19.27.4 Three-phase voltage measurement (VMMXU)
Table 73: Three-phase voltage measurement (VMMXU)
Hz
At voltages in range 0.01…1.15 × U n
±0.5% or ±0.002 × U n

RMS: No suppression
19.27.5 Residual voltage measurement (RESVMMXU)
Table 74: Residual voltage measurement (RESVMMXU)
Operation accuracy Depending on the frequency of the measured voltage: f/f n =
±2 Hz
±0.5% or ±0.002 × U n

RMS: No suppression
REM615 49
Product Guide
19.27.6 Sequence voltage measurement (VSMSQI)
Table 75: Sequence voltage measurement (VSMSQI)
Hz
At voltages in range 0.01…1.15 × U n
±1.0% or ±0.002 × U n
19.27.7 Three-phase power and energy measurement (PEMMXU)
Table 76: Three-phase power and energy measurement (PEMMXU)
Operation accuracy At all three currents in range 0.10…1.20 × I n
At all three voltages in range 0.50…1.15 × U n
At the frequency f n ±1 Hz
±1.5% for apparent power S

±1.5% for active power P and active energy 49
±1.5% for reactive power Q and reactive energy 50
±0.015 for power factor
19.27.8 RTD/mA measurement (XRGGIO130)
Table 77: RTD/mA measurement (XRGGIO130)
Description Value
RTD inputs Supported RTD sensors 100 Ω platinum TCR 0.00385 (DIN 43760)
250 Ω platinum TCR 0.00385
100 Ω nickel TCR 0.00618 (DIN 43760)
10 Ω copper TCR 0.00427
Supported resistance range 0...2 kΩ

Maximum lead resistance
(three-wire measurement) 25 Ω per lead
Isolation 2 kV (inputs to protective earth)
Response time <4 s

49 |PF| >0.5 which equals |cosφ| >0.5

50 |PF| <0.86 which equals |sinφ| >0.5
50 REM615
Product Guide
Description Value
RTD/resistance sensing cur-
rent Maximum 0.33 mA rms
Operation accuracy Resistance Temperature
± 2.0% or ±1 Ω ±1°C
10 Ω copper: ±2°C
mA inputs Supported current range 0…20 mA

Current input impedance 44 Ω ± 0.1%
Operation accuracy ±0.5% or ±0.01 mA
19.27.9 Frequency measurement (FMMXU)
Table 78: Frequency measurement (FMMXU)
Operation accuracy ±5 mHz
(in measurement range 35...75 Hz)
19.28 Other functions
19.28.1 Pulse timer (PTGAPC)
Table 79: Pulse timer (PTGAPC)
19.28.2 Time delay off (8 pcs) (TOFPAGC)
Table 80: Time delay off (8 pcs) (TOFPAGC)
19.28.3 Time delay on (8 pcs) (TONGAPC)
Table 81: Time delay on (8 pcs) (TONGAPC)
is suited for relay installations where the

20. Local HMI front panel user interface is frequently used
and a single line diagram is required. The
small display is suited for remotely controlled
The relay is available with two optional displays,
substations where the relay is only occasionally
a large one and a small one. The large display
REM615 51
Product Guide
accessed locally via the front panel user Graphical Display Editor in PCM600. The user
interface. can create up to 10 SLD pages.
Both LCD displays offer front-panel user The local HMI includes a push button (L/R)
interface functionality with menu navigation for local/remote operation of the relay. When
and menu views. However, the large display the relay is in the local mode, it can be
offers increased front-panel usability with operated only by using the local front panel
less menu scrolling and improved information user interface. When the relay is in the remote
overview. In addition, the large display includes mode, it can execute commands sent from a
a user-configurable single line diagram (SLD) remote location. The relay supports the remote
with position indication for the associated selection of local/remote mode via a binary
primary equipment. Depending on the chosen input. This feature facilitates, for example, the
standard configuration, the relay displays the use of an external switch at the substation
related measuring values, apart from the to ensure that all relays are in the local mode
default single line diagram. The SLD view can during maintenance work and that the circuit
also be accessed using the Web browser-based breakers cannot be operated remotely from the
user interface. The default SLD can be modified network control center.
according to user requirements by using the
Figure 12: Small display Figure 13: Large display
Table 82: Small display
Character size80 Rows in the view Characters per row

Small, mono-spaced (6 × 12 pixels) 5 20
Large, variable width (13 × 14 pixels) 3 8 or more
Table 83: Large display
Character size80 Rows in the view Characters per row

Small, mono-spaced (6 × 12 pixels) 10 20
Large, variable width (13 × 14 pixels) 7 8 or more
80 Depending on the selected language
52 REM615
Product Guide
18, which can be mounted side by side with the

21. Mounting methods relay cases.
Mounting methods
By means of appropriate mounting accessories,
• Flush mounting
the standard relay case can be flush mounted,
semi-flush mounted or wall mounted. The flush • Semi-flush mounting
mounted and wall mounted relay cases can • Semi-flush mounting in a 25° tilt
also be mounted in a tilted position (25°) using • Rack mounting
special accessories. • Wall mounting
Further, the relays can be mounted in any • Mounting to a 19" equipment frame
standard 19” instrument cabinet by means of • Mounting with an RTXP 18 test switch to a
19” mounting panels available with cut-outs 19" rack
for one or two relays. Alternatively, the relays Panel cut-out for flush mounting
can be mounted in 19” instrument cabinets by
means of 4U Combiflex equipment frames. • Height: 161.5 ±1 mm
• Width: 165.5 ±1 mm
For routine testing purposes, the relay cases
can be equipped with test switches, type RTXP
190
6
18
164
177
25°
160
160
177
177
230
98
107
48 133
153
103
Figure 14: Flush mounting Figure 15: Semi-flush mounting Figure 16: Semi-flush mounting
in a 25º tilt
23. Selection and ordering data

22. Relay case and plug-in unit
Use ABB Library to access the selection and
The relay cases are assigned to a certain ordering information and to generate the order
type of plug-in unit. For safety reasons, the number.
relay cases for current measuring relays are Product Selection Tool (PST), a Next-Generation
provided with automatically operating contacts Order Number Tool, supports order code
for shortcircuiting the CT secondary circuits creation for ABB Distribution Automation IEC
when a relay unit is withdrawn from its products with emphasis on, but not exclusively
case. The relay case is further provided with for, the Relion product family. PST is an easy-
a mechanical coding system preventing the to-use, online tool always containing the latest
current measuring relay units from being product information. The complete order code
inserted into relay cases intended for voltage can be created with detailed specification
measuring relay units. and the result can be printed and mailed.
Registration is required.
REM615 53
Product Guide
24. Accessories and ordering data
Table 84: Cables
Item Order number
Optical sensor for arc protection, cable length 1.5 m 1MRS120534-1.5
Optical sensor for arc protection, cable length 3.0 m 1MRS120534-3
Table 85: Mounting accessories
Item Order number
Semi-flush mounting kit 1MRS050696
Wall mounting kit 1MRS050697
Inclined semi-flush mounting kit 1MRS050831
19” rack mounting kit with cut-out for one relay 1MRS050694
19” rack mounting kit with cut-out for two relays 1MRS050695
Mounting bracket for one relay with test switch RTXP in 4U Combiflex (RHGT 19” variant C) 2RCA022642P0001
Mounting bracket for one relay in 4U Combiflex (RHGT 19” variant C) 2RCA022643P0001
19” rack mounting kit for one relay and one RTXP18 test switch (the test switch is not included in the 2RCA021952A0003
delivery)
19” rack mounting kit for one relay and one RTXP24 test switch (the test switch is not included in the 2RCA022561A0003
delivery)
Functional earthing flange for RTD modules51 2RCA036978A0001
Replacement kit for a Strömberg SP_J40 series relay (cut-out in the center of the installation plate) 2RCA027871A0001
Replacement kit for a Strömberg SP_J40 series relay (cut-out on the left or the right of the installa- 2RCA027874A0001
tion plate)
Replacement kit for two Strömberg SP_J3 series relays 2RCA027880A0001
19” rack replacement kit for Strömberg SP_J3/J6 series relays (one cut-out) 2RCA027894A0001
19” rack replacement kit for Strömberg SP_J3/J6 series relays (two cut-outs) 2RCA027897A0001
51 Cannot be used when the protection relay is mounted with the Combiflex 19" equipment frame
(2RCA032826A0001)
54 REM615
Product Guide
Item Order number
Replacement kit for a Strömberg SP_J6 series relay 2RCA027881A0001
Replacement kit for three BBC S_ series relays 2RCA027882A0001
Replacement kit for a SPA 300 series relay 2RCA027885A0001
a Web browser (Internet Explorer). For security

25. Tools reasons, the Web HMI is disabled by default but
it can be enabled via the local HMI. The Web HMI
functionality can be limited to read-only access.
The protection relay is delivered as a
preconfigured unit. The default parameter The relay connectivity package is a collection
setting values can be changed from the of software and specific relay information,
frontpanel user interface (local HMI), the Web which enables system products and tools to
browser-based user interface (Web HMI) or connect and interact with the protection relay.
Protection and Control IED Manager PCM600 in The connectivity packages reduce the risk of
combination with the relay-specific connectivity errors in system integration, minimizing device
package. configuration and setup times. Further, the
connectivity packages for protection relays
PCM600 offers extensive relay configuration
of this product series include a flexible
functions. For example, depending on the
update tool for adding one additional local
protection relay, the relay signals, application,
HMI language to the protection relay. The
graphical display and single-line diagram, and
update tool is activated using PCM600, and
IEC 61850 communication, including horizontal
it enables multiple updates of the additional
GOOSE communication, can be modified with
HMI language, thus offering flexible means for
PCM600.
possible future language updates.
When the Web HMI is used, the protection relay
can be accessed either locally or remotely using
Table 86: Tools
Description Version
PCM600 2.6 (Rollup 20150626) or later
Web browser IE 8.0, IE 9.0, IE 10.0 or IE 11.0
REM615 Connectivity Package 5.1 or later
Table 87: Supported functions
Function Web HMI PCM600
Relay parameter setting ● ●
Saving of relay parameter settings in the relay ● ●
Signal monitoring ● ●
Disturbance recorder handling ● ●
Alarm LED viewing ● ●
Access control management ● ●
Relay signal configuration (Signal Matrix) – ●
REM615 55
Product Guide
Function Web HMI PCM600

®
Modbus communication configuration (communication man- – ●
agement)
DNP3 communication configuration (communication manage- – ●

ment)
IEC 60870-5-103 communication configuration (communica- – ●

tion management)
Saving of relay parameter settings in the tool – ●
Disturbance record analysis – ●
XRIO parameter export/import ● ●
Graphical display configuration – ●
Application configuration – ●
IEC 61850 communication configuration, GOOSE (communica- – ●

tion configuration)
Phasor diagram viewing ● –
Event viewing ● ●
Saving of event data on the user's PC ● ●
Online monitoring – ●
● = Supported or regular component exchange to maintain

the memory storage. FTP and Web HMI use
TLS encryption with a minimum of 128 bit
26. Cyber security key length protecting the data in transit. In
this case the used communication protocols
The relay supports role based user are FTPS and HTTPS. All rear communication
authentication and authorization. It can store ports and optional protocol services can be
2048 audit trail events to a nonvolatile memory. deactivated according to the required system
The non-volatile memory is based on a memory setup.
type which does not need battery backup
56 REM615
Product Guide
27. Terminal diagrams
Figure 17: Terminal diagram of standard configuration A
REM615 57
Product Guide
Figure 18: Terminal diagram of standard configuration B
58 REM615
Product Guide
Figure 19: Terminal diagram of standard configuration C
REM615 59
Product Guide
REM615
X130 X100
+ 1
1 0,2/1A
U aux
Io 2
2 N -
3
X131 IRF
4
4 5
IL1
5
7 PO1
U1
8 6
X132 7
4 PO2
IL2
5
8
7 9
U2
8 10
X133 SO1
11
4 12
IL3
5 13
7 SO2
U3
8 14
16
PO3
17
15
19
TCS1 18
20
22
PO4
21
23
TCS2 24
X110 X110
1 14
BI 1
2 SO1
16
3 15
BI 2
4 17
SO2
5
BI 3 19
6 18
20
BI 4 SO3
7
22
8 21
BI 5 23
9
SO4
BI 6 24
10
11
BI 7
12
BI 8
13
X13
1)
Light sensor input 1
X14
1)
Light sensor input 2
1) Optional
2) The IED features an automatic short-circuit
X15
1) mechanism in the CT connector when plug-in
Light sensor input 3 unit is detached
Figure 20: Terminal diagram of standard configuration D
28. Certificates 29. References
DNV GL has issued an IEC 61850 Edition 2 The www.abb.com/substationautomation

Certificate Level A1 for Relion® 615 series. portal provides information on the entire
Certificate number: 7410570I-OPE/INC 15-1136. range of distribution automation products and
services.
DNV GL has issued an IEC 61850 Edition 1
Certificate Level A1 for Relion® 615 series. The latest relevant information on the REM615
Certificate number: 74105701-OPE/INC 15-1145. protection and control relay is found on the
product page. Scroll down the page to find and
UL 508 and CAN/CSA C22.2 No. 14-13, Industrial
download the related documentation.
Control Equipment.
Additional certificates can be found on the
product page.
60 REM615
Product Guide
30. Functions, codes and symbols
Table 88: Functions included in the relay
Function IEC 61850 IEC 60617 IEC-ANSI

Protection
Three-phase non-directional overcurrent PHLPTOC1 3I> (1) 51P-1 (1)
protection, low stage
Three-phase non-directional overcurrent PHHPTOC1 3I>> (1) 51P-2 (1)
protection, high stage
Three-phase non-directional overcurrent PHIPTOC1 3I>>> (1) 50P/51P (1)
protection, instantaneous stage
Non-directional earth-fault protection, low EFLPTOC1 Io> (1) 51N-1 (1)
stage
Non-directional earth-fault protection, high EFHPTOC1 Io>> (1) 51N-2 (1)
stage
Directional earth-fault protection, low stage DEFLPDEF1 Io> -> (1) 67N-1 (1)
Three-phase undervoltage protection PHPTUV1 3U< (1) 27 (1)
Positive-sequence undervoltage protection PSPTUV1 U1< (1) 47U+ (1)
Negative-sequence overvoltage protection NSPTOV1 U2> (1) 47O- (1)
Frequency protection FRPFRQ1 f>/f<,df/dt (1) 81 (1)
FRPFRQ2 f>/f<,df/dt (2) 81 (2)
Negative-sequence overcurrent protection MNSPTOC1 I2>M (1) 46M (1)
for machines
MNSPTOC2 I2>M (2) 46M (2)
Loss of load supervision LOFLPTUC1 3I< (1) 37 (1)
Motor load jam protection JAMPTOC1 Ist> (1) 51LR (1)
Motor start-up supervision STTPMSU1 Is2t n< (1) 49,66,48,51LR (1)
Phase reversal protection PREVPTOC1 I2>> (1) 46R (1)
Thermal overload protection for motors MPTTR1 3Ith>M (1) 49M (1)
Circuit breaker failure protection CCBRBRF1 3I>/Io>BF (1) 51BF/51NBF (1)
Master trip TRPPTRC1 Master Trip (1) 94/86 (1)
TRPPTRC2 Master Trip (2) 94/86 (2)
Arc protection ARCSARC1 ARC (1) 50L/50NL (1)
ARCSARC2 ARC (2) 50L/50NL (2)
ARCSARC3 ARC (3) 50L/50NL (3)
Multipurpose protection MAPGAPC1 MAP (1) MAP (1)
MAPGAPC2 MAP (2) MAP (2)
REM615 61
Product Guide

Control
Circuit-breaker control CBXCBR1 I <-> O CB (1) I <-> O CB (1)
Disconnector control DCXSWI1 I <-> O DCC (1) I <-> O DCC (1)
DCXSWI2 I <-> O DCC (2) I <-> O DCC (2)
Earthing switch control ESXSWI1 I <-> O ESC (1) I <-> O ESC (1)
Disconnector position indication DCSXSWI1 I <-> O DC (1) I <-> O DC (1)
DCSXSWI2 I <-> O DC (2) I <-> O DC (2)
DCSXSWI3 I <-> O DC (3) I <-> O DC (3)
Earthing switch indication ESSXSWI1 I <-> O ES (1) I <-> O ES (1)
ESSXSWI2 I <-> O ES (2) I <-> O ES (2)
Emergency start-up ESMGAPC1 ESTART (1) ESTART (1)
Condition monitoring and supervision
Circuit-breaker condition monitoring SSCBR1 CBCM (1) CBCM (1)
Trip circuit supervision TCSSCBR1 TCS (1) TCM (1)
TCSSCBR2 TCS (2) TCM (2)
Current circuit supervision CCSPVC1 MCS 3I (1) MCS 3I (1)
Fuse failure supervision SEQSPVC1 FUSEF (1) 60 (1)
Runtime counter for machines and devices MDSOPT1 OPTS (1) OPTM (1)
Measurement
Disturbance recorder RDRE1 DR (1) DFR (1)
Load profile record LDPRLRC1 LOADPROF (1) LOADPROF (1)
Fault record FLTRFRC1 FAULTREC (1) FAULTREC (1)
Three-phase current measurement CMMXU1 3I (1) 3I (1)
Sequence current measurement CSMSQI1 I1, I2, I0 (1) I1, I2, I0 (1)
Residual current measurement RESCMMXU1 Io (1) In (1)
Three-phase voltage measurement VMMXU1 3U (1) 3V (1)
Residual voltage measurement RESVMMXU1 Uo (1) Vn (1)
Sequence voltage measurement VSMSQI1 U1, U2, U0 (1) V1, V2, V0 (1)
Three-phase power and energy measure- PEMMXU1 P, E (1) P, E (1)
ment
RTD/mA measurement XRGGIO130 X130 (RTD) (1) X130 (RTD) (1)
Frequency measurement FMMXU1 f (1) f (1)
IEC 61850-9-2 LE sampled value sending SMVSENDER SMVSENDER SMVSENDER
IEC 61850-9-2 LE sampled value receiving SMVRCV SMVRCV SMVRCV
(voltage sharing)
Other
Minimum pulse timer (2 pcs) TPGAPC1 TP (1) TP (1)
TPGAPC2 TP (2) TP (2)
62 REM615
Product Guide

Minimum pulse timer (2 pcs, second resolu- TPSGAPC1 TPS (1) TPS (1)
tion)
Minimum pulse timer (2 pcs, minute resolu- TPMGAPC1 TPM (1) TPM (1)
tion)
Pulse timer (8 pcs) PTGAPC1 PT (1) PT (1)
PTGAPC2 PT (2) PT (2)
Time delay off (8 pcs) TOFGAPC1 TOF (1) TOF (1)
TOFGAPC2 TOF (2) TOF (2)
Time delay on (8 pcs) TONGAPC1 TON (1) TON (1)
TONGAPC2 TON (2) TON (2)
Set-reset (8 pcs) SRGAPC1 SR (1) SR (1)
SRGAPC2 SR (2) SR (2)
Move (8 pcs) MVGAPC1 MV (1) MV (1)
MVGAPC2 MV (2) MV (2)
Generic control point (16 pcs) SPCGAPC1 SPC (1) SPC (1)
SPCGAPC2 SPC (2) SPC (2)
Analog value scaling SCA4GAPC1 SCA4 (1) SCA4 (1)
SCA4GAPC2 SCA4 (2) SCA4 (2)
Integer value move MVI4GAPC1 MVI4 (1) MVI4 (1)
31. Document revision history
Document revision/date Product version History
A/2009-07-03 2.0 First release
B/2009-10-01 2.0 Content updated
C/2010-06-11 3.0 Content updated to correspond to the product ver-

sion
D/2010-06-29 3.0 Terminology updated
E/2010-09-07 3.0 Content updated
F/2012-05-11 4.0 Content updated to correspond to the product ver-

sion
G/2013-02-21 4.0 FP1 Content updated to correspond to the product ver-

sion
REM615 63
Product Guide
Document revision/date Product version History
H/2014-01-24 5.0 Content updated to correspond to the product ver-

sion
K/2014-09-04 5.0 Content updated
L/2015-10-30 5.0 FP1 Content updated to correspond to the product ver-

sion
M/2016-05-20 5.0 FP1 Content updated
N/2018-12-20 5.0 FP1 Content updated
P/2021-12-30 5.0 FP1 Content updated
64 REM615
Product Guide
—
ABB Distribution Solutions
Digital Substation Products
P.O.Box 699
FI-65101 VAASA, Finland
Phone +358 10 22 11
ABB India Ltd,

Digital Substation Products
Maneja Works
Vadodara-390013, India
Phone: +91 265 6724402
Fax: +91 265 6724407
www.abb.com/mediumvoltage
www.abb.com/relion
www.abb.com/substationautomation
1MRS756890 P
© Copyright 2022 ABB. All rights reserved.

REM615 PG 756890 ENp

Uploaded by

Copyright:

Available Formats

REM615 PG 756890 ENp

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

REM615 PG 756890 ENp

Uploaded by

Copyright:

Available Formats

—

RELION® 615 SERIES

Motor Protection and Control REM615

ABB and Relion are registered • Electromagnetic Compatibility Regulations 2016

1. Description 2. Standard configuration

REM615 MOTOR PROTECTION AND CONTROL RELAY STANDARD

PROTECTION LOCAL HMI ALSO AVAILABLE

- Disturbance and fault recorders

Lockout relay Lockout relay

- Local/Remote push button on LHMI

3I< I2>M I2>> - Web HMI

Is2t n< 3Ith>M

CONDITION MONITORING COMMUNICATION

CONTROL AND INDICATION 1) MEASUREMENT

from technical documentation Current transformer 4

Figure 1: Functionality overview for standard configuration A

REM615 MOTOR PROTECTION AND CONTROL RELAY STANDARD

PROTECTION LOCAL HMI ALSO AVAILABLE

- Disturbance and fault recorders

Lockout relay Lockout relay

- Local/Remote push button on LHMI

3I< I2>M I2>> - Web HMI

Is2t n< 3Ith>M

CONDITION MONITORING COMMUNICATION

from technical documentation Current transformer 4

Figure 2: Functionality overview for standard configuration B

REM615 MOTOR PROTECTION AND CONTROL RELAY STANDARD

PROTECTION LOCAL HMI ALSO AVAILABLE

- Disturbance and fault recorders

Lockout relay Lockout relay

- Local/Remote push button on LHMI

3I< I2>M I2>> - Web HMI

Is2t n< 3Ith>M

CONDITION MONITORING COMMUNICATION

from technical documentation Current transformer 4

Figure 3: Functionality overview for standard configuration C

REM615 MOTOR PROTECTION AND CONTROL RELAY STANDARD

PROTECTION LOCAL HMI ALSO AVAILABLE

- Disturbance and fault recorders

Lockout relay Lockout relay

- Local/Remote push button on LHMI

3I< I2>M I2>> - Web HMI

Is2t n< 3Ith>M

CONDITION MONITORING COMMUNICATION

from technical documentation Current sensor 3

Figure 4: Functionality overview for standard configuration D

Table 1: Standard configuration

Description Std. conf.

Basic motor protection (RTD option) A

Table 2: Supported functions

Function IEC 61850 A B C D

Three-phase non-directional overcurrent protec- PHLPTOC 1 1 1 1

Table continues on the next page

Motor Protection and Control REM615 1MRS756890 P

Function IEC 61850 A B C D

Three-phase non-directional overcurrent protec- PHHPTOC 1 1 1 1

Three-phase non-directional overcurrent protec- PHIPTOC 1 1 1 1

Non-directional earth-fault protection, low EFLPTOC 1

Non-directional earth-fault protection, high EFHPTOC 1 1 1 1