IRFPG50

www.vishay.com
Vishay Siliconix
Power MOSFET
D
FEATURES
• Dynamic dV/dt rated
TO-247AC
• Repetitive avalanche rated
• Isolated central mounting hole Available
• Fast switching
G • Ease of paralleling
• Simple drive requirements
S • Material categorization: for definitions of compliance
D please see www.vishay.com/doc?99912
G S
Note
N-Channel MOSFET * This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
PRODUCT SUMMARY Please see the information / tables in this datasheet for details
VDS (V) 1000 DESCRIPTION
RDS(on) (Ω) VGS = 10 V 2.0 Third generation Power MOSFETs from Vishay provide the
Qg (max.) (nC) 190 designer with the best combination of fast switching,
Qgs (nC) 23 ruggedized device design, low on-resistance and
cost-effectiveness.
Qgd (nC) 110
The TO-247AC package is preferred for
Configuration Single
commercial-industrial applications where higher power
levels preclude the use of TO-220AB devices. The
TO-247AC is similar but superior to the earlier TO-218
package because its isolated mounting hole. It also provides
greater creepage distances between pins to meet the
requirements of most safety specifications.

ORDERING INFORMATION
Package TO-247AC
Lead (Pb)-free IRFPG50PbF

ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)

PARAMETER SYMBOL LIMIT UNIT
Drain-source voltage VDS 1000
V
Gate-source voltage VGS ± 20
TC = 25 °C 6.1
Continuous drain current VGS at 10 V ID
TC = 100 °C 3.9 A
Pulsed drain current a IDM 24
Linear derating factor 1.5 W/°C
Single pulse avalanche energy b EAS 800 mJ
Repetitive avalanche current a IAR 6.0 A
Repetitive avalanche energy a EAR 19 mJ
Maximum power dissipation TC = 25 °C PD 190 W
Peak diode recovery dV/dt c dV/dt 1.0 V/ns
Operating junction and storage temperature range TJ, Tstg -55 to +150
°C
Soldering recommendations (peak temperature) for 10 s 300 d
10 lbf · in
Mounting torque 6-32 or M3 screw
1.1 N·m
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11)
b. VDD = 50 V, starting TJ = 25 °C, L = 40 mH, Rg = 25 Ω, IAS = 6.1 A (see fig. 12)
c. ISD ≤ 6.1 A, dI/dt ≤ 120 A/μs, VDD ≤ 600, TJ ≤ 150 °C
d. 1.6 mm from case

S22-0057-Rev. C, 31-Jan-2022 1 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 IRFPG50
www.vishay.com
Vishay Siliconix

THERMAL RESISTANCE RATINGS

PARAMETER SYMBOL TYP. MAX. UNIT
Maximum junction-to-ambient RthJA - 40
Case-to-sink, flat, greased surface RthCS 0.24 - °C/W
Maximum junction-to-case (drain) RthJC - 0.65

SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)

PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Static
Drain-source breakdown voltage VDS VGS = 0 V, ID = 250 μA 1000 - - V
VDS temperature coefficient ΔVDS/TJ Reference to 25 °C, ID = 1 mA - 1.2 - V/°C
Gate-source threshold voltage VGS(th) VDS = VGS, ID = 250 μA 2.0 - 4.0 V
Gate-source leakage IGSS VGS = ± 20 V - - ± 100 nA
VDS = 1000 V, VGS = 0 V - - 100
Zero gate voltage drain current IDSS μA
VDS = 800 V, VGS = 0 V, TJ = 125 °C - - 500
Drain-source on-state resistance RDS(on) VGS = 10 V ID = 3.6 A b - - 2.0 Ω
Forward transconductance gfs VDS = 100 V, ID = 3.6 Ab 5.4 - - S
Dynamic
Input capacitance Ciss - 2800 -
VGS = 0 V,
Output capacitance Coss VDS = 25 V, - 250 - pF
f = 1.0 MHz, see fig. 5
Reverse transfer capacitance Crss - 84 -
Total gate charge Qg - - 190
ID = 6.1 A, VDS = 400 V,
Gate-source charge Qgs VGS = 10 V - - 23 nC
see fig. 6 and 13 b
Gate-drain charge Qgd - - 110
Turn-on delay time td(on) - 19 -
Rise time tr VDD = 500 V, ID = 6.1 A, - 35 -
ns
Turn-off delay time td(off) Rg = 6.2 Ω, RD = 81 Ω, see fig. 10 b - 130 -
Fall time tf - 36 -

Internal drain inductance LD Between lead, D

- 5.0 -
6 mm (0.25") from
package and center of G
nH
Internal source inductance LS die contact - 13 -
S

Drain-Source Body Diode Characteristics

Continuous source-drain diode current IS MOSFET symbol D

- - 6.1
showing the
A
integral reverse G

Pulsed diode forward current a ISM p - n junction diode S - - 24

Body diode voltage VSD TJ = 25 °C, IS = 6.1 A, VGS = 0 V b - - 1.8 V

Body diode reverse recovery time trr - 630 950 ns
TJ = 25 °C, IF = 6.1 A, dI/dt = 100 A/μs b
Body diode reverse recovery charge Qrr - 3.5 5.3 μC
Forward turn-on time ton Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11)
b. Pulse width ≤ 300 μs; duty cycle ≤ 2 %

S22-0057-Rev. C, 31-Jan-2022 2 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 IRFPG50
www.vishay.com
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)

Fig. 1 - Typical Output Characteristics, TC = 25 °C Fig. 3 - Typical Transfer Characteristics

Fig. 2 - Typical Output Characteristics, TC = 150 °C Fig. 4 - Normalized On-Resistance vs. Temperature

S22-0057-Rev. C, 31-Jan-2022 3 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 IRFPG50
www.vishay.com
Vishay Siliconix

Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage Fig. 7 - Typical Source-Drain Diode Forward Voltage

Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage Fig. 8 - Maximum Safe Operating Area

S22-0057-Rev. C, 31-Jan-2022 4 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 IRFPG50
www.vishay.com
Vishay Siliconix

RD
VDS

VGS
D.U.T.
RG
+
- VDD

10 V
Pulse width ≤ 1 µs
Duty factor ≤ 0.1 %

Fig. 10 - Switching Time Test Circuit

VDS
90 %

10 %
VGS
td(on) tr td(off) tf
Fig. 9 - Maximum Drain Current vs. Case Temperature
Fig. 11 - Switching Time Waveforms

Fig. 12 - Maximum Effective Transient Thermal Impedance, Junction-to-Case

S22-0057-Rev. C, 31-Jan-2022 5 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 IRFPG50
www.vishay.com
Vishay Siliconix

L
VDS VDS
Vary tp to obtain
tp
required IAS
VDD
RG D.U.T +
V DD
- VDS
IAS
10 V
tp 0.01 Ω
IAS

Fig. 13 - Unclamped Inductive Test Circuit Fig. 14 - Unclamped Inductive Waveforms

Fig. 15 - Maximum Avalanche Energy vs. Drain Current

Current regulator
Same type as D.U.T.

QG 50 kΩ
10 V 12 V 0.2 µF
0.3 µF

QGS QGD +
VDS
D.U.T. -

VG
VGS

3 mA

Charge
IG ID
Current sampling resistors

Fig. 16 - Basic Gate Charge Waveform Fig. 17 - Gate Charge Test Circuit

S22-0057-Rev. C, 31-Jan-2022 6 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 IRFPG50
www.vishay.com
Vishay Siliconix

Peak Diode Recovery dV/dt Test Circuit

+ Circuit layout considerations

D.U.T.
• Low stray inductance
• Ground plane
• Low leakage inductance
current transformer
-

- +
-

Rg • dV/dt controlled by Rg +
• Driver same type as D.U.T. VDD
-
• ISD controlled by duty factor “D”
• D.U.T. - device under test

Driver gate drive

Period P.W.
D=
P.W. Period

VGS = 10 Va

D.U.T. lSD waveform

Reverse
recovery Body diode forward
current current
dI/dt
D.U.T. VDS waveform
Diode recovery
dV/dt
VDD

Re-applied
voltage
Body diode forward drop
Inductor current

Ripple ≤ 5 % ISD

Note
a. VGS = 5 V for logic level devices

Fig. 18 - For N-Channel

Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?91254.

S22-0057-Rev. C, 31-Jan-2022 7 Document Number: 91254

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Package Information
www.vishay.com
Vishay Siliconix
TO-247AC (High Voltage)
VERSION 1: FACILITY CODE = 9

MILLIMETERS MILLIMETERS
DIM. MIN. NOM. MAX. NOTES DIM. MIN. NOM. MAX. NOTES
A 4.83 5.02 5.21 D1 16.46 16.76 17.06 5
A1 2.29 2.41 2.55 D2 0.56 0.66 0.76
A2 1.17 1.27 1.37 E 15.50 15.70 15.87 4
b 1.12 1.20 1.33 E1 13.46 14.02 14.16 5
b1 1.12 1.20 1.28 E2 4.52 4.91 5.49 3
b2 1.91 2.00 2.39 6 e 5.46 BSC
b3 1.91 2.00 2.34 L 14.90 15.15 15.40
b4 2.87 3.00 3.22 6, 8 L1 3.96 4.06 4.16 6
b5 2.87 3.00 3.18 ØP 3.56 3.61 3.65 7
c 0.40 0.50 0.60 6 Ø P1 7.19 ref.
c1 0.40 0.50 0.56 Q 5.31 5.50 5.69
D 20.40 20.55 20.70 4 S 5.51 BSC
Notes
(1) Package reference: JEDEC® TO247, variation AC
(2) All dimensions are in mm
(3) Slot required, notch may be rounded
(4) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm per side. These dimensions are measured at the
outermost extremes of the plastic body
(5) Thermal pad contour optional with dimensions D1 and E1
(6) Lead finish uncontrolled in L1
(7) Ø P to have a maximum draft angle of 1.5° to the top of the part with a maximum hole diameter of 3.91 mm
(8) Dimension b2 and b4 does not include dambar protrusion. Allowable dambar protrusion shall be 0.1 mm total in excess of b2 and b4
dimension at maximum material condition

Revision: 31-Oct-2022 1 Document Number: 91360

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Package Information
www.vishay.com
Vishay Siliconix
VERSION 2: FACILITY CODE = Y
A A
4
E 7 ØP (Datum B)
B
E/2 S A2 Ø k M DBM
3 R/2 ØP1
A
D2
Q

4 4
2xR
D D1
(2)

1 2 3 D 4
Thermal pad
5 L1

C L 4
E1
See view B A
0.01 M D B M
2 x b2 C View A - A
2x e
3xb
b4 A1
0.10 M C A M
(b1, b3, b5)
Planting Base metal
Lead Assignments
1. Gate D DE E
2. Drain
3. Source (c) c1
C C
4. Drain
(b, b2, b4)
(4)
Section C - C, D - D, E - E
View B

MILLIMETERS MILLIMETERS
DIM. MIN. MAX. NOTES DIM. MIN. MAX. NOTES
A 4.58 5.31 D2 0.51 1.30
A1 2.21 2.59 E 15.29 15.87
A2 1.17 2.49 E1 13.72 -
b 0.99 1.40 e 5.46 BSC
b1 0.99 1.35 Øk 0.254
b2 1.53 2.39 L 14.20 16.25
b3 1.65 2.37 L1 3.71 4.29
b4 2.42 3.43 ØP 3.51 3.66
b5 2.59 3.38 Ø P1 - 7.39
c 0.38 0.86 Q 5.31 5.69
c1 0.38 0.76 R 4.52 5.49
D 19.71 20.82 S 5.51 BSC
D1 13.08 -
Notes
(1) Dimensioning and tolerancing per ASME Y14.5M-1994
(2) Contour of slot optional
(3) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at
the outermost extremes of the plastic body
(4) Thermal pad contour optional with dimensions D1 and E1
(5) Lead finish uncontrolled in L1
(6) Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154")
(7) Outline conforms to JEDEC outline TO-247 with exception of dimension c

Revision: 31-Oct-2022 2 Document Number: 91360

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Package Information
www.vishay.com
Vishay Siliconix
VERSION 3: FACILITY CODE = N
A
A

D2
B E P1
R/2 P
N A2

K M D BM
R

D1
D

D
L1

L
b4 C E1
b2 e A1
b 0.01 M D B M

0.10 M C A M
b1, b3, b5
Base metal

c1
c

b, b2, b4
Plating

MILLIMETERS MILLIMETERS
DIM. MIN. MAX. DIM. MIN. MAX.
A 4.65 5.31 D2 0.51 1.35
A1 2.21 2.59 E 15.29 15.87
A2 1.17 1.37 E1 13.46 -
b 0.99 1.40 e 5.46 BSC
b1 0.99 1.35 k 0.254
b2 1.65 2.39 L 14.20 16.10
b3 1.65 2.34 L1 3.71 4.29
b4 2.59 3.43 N 7.62 BSC
b5 2.59 3.38 P 3.56 3.66
c 0.38 0.89 P1 - 7.39
c1 0.38 0.84 Q 5.31 5.69
D 19.71 20.70 R 4.52 5.49
D1 13.08 - S 5.51 BSC
ECN: E22-0452-Rev. G, 31-Oct-2022
DWG: 5971
Notes
(1) Dimensioning and tolerancing per ASME Y14.5M-1994
(2) Contour of slot optional
(3) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at
the outermost extremes of the plastic body
(4) Thermal pad contour optional with dimensions D1 and E1
(5) Lead finish uncontrolled in L1
(6) Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154")

Revision: 31-Oct-2022 3 Document Number: 91360

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.

Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

© 2024 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED

Revision: 01-Jan-2024 1 Document Number: 91000

For technical questions, contact:
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000