Advabond SBR TDS

ADVABOND SBR
SBR based bonding agent and admixture
DESCRIPTION
ADVABOND SBR is a Styrene Butadiene Rubber co-polymer based product
which is used in mortar and concrete as an admixture and bonding agent to
increase its water resistance and durability.
USES
Admixture: as an admixture for cementitious systems and tile
adhesives/grouts. Improves the durability, water proofing and abrasion
resistance properties of mortars.
Bonding: for bonding of new to old concrete, tile bedding and fixing of slip
bricks.
Repair of concrete.
Waterproofing internally: basements, swimming pools, potable water

tanks, sludge tanks, and ducts, tunnels and underpasses.
Waterproofing externally: structures above ground.
Waterproof bonding: bricks slips, copings, precast treads and risers.
Waterproofing suspended floors: patios, walkways, balconies, wet areas,

AL SA’FAT - GREEN BUILDING plant rooms.
Certiﬁcate No. CL20020739
Waterproof/protective slurries: potable water tanks, sewerage and mild

chemical holding tanks, porous concrete, block work and long term
protection of reinforcements or friable concrete soffits.
ADVANTAGES
Compatible with all types of cements.
Can be applied in thin screed without cracking.
Can be used in potable water applications.
Easy to use.
Enhances the flexural and tensile strength of the mortar and render.
Excellent adhesion to most building materials.
Good resistance to salt permeation.
Improves the chemical and abrasion resistant properties of the mortar.
Provides good resistance to water and moisture vapour transmission.
Prolonged corrosion protection.
Reduce shrinkage.
Reduce the water/cement ratio.
APPLICATION INSTRUCTIONS
Surface preparation
Surface to which ADVABOND SBR mixes are to be applied shall be clean,
sound and free of all loose particles. Remove all laitance, oil & grease,
mould oil, curing compound from surface. Ensure that the exposed
reinforcing steel is clean and free from scale and rust. When repairing
damaged concrete, ensure that the concrete has been cut back to
thoroughly sound material.
Al Mutathawir Insulation Materials Industries L.L.C.

T: +971 6 5345585 | F: +971 6 5347717
E: [email protected] | W: www.aim-insu.com
P.O. Box: 22704,Sharjah-UAE
ADVABOND SBR
Bonding slurry
Saturate absorbent surfaces with water completely till it reaches a saturate surface dry condition. However, ensure
that the surface is free of standing water. Prepare a bonding slurry by mixing 2 parts O.P. cement to 1 part of
ADVABOND SBR (by volume). Using a stiff brush, work the bonding slurry well into the damp surface, ensuring that no
pinholes are visible. Do not apply bonding slurry at a thickness in excess of 2mm. If a second coat is necessary, it must
be applied at right angles to the first to ensure complete coverage.
(Approximately 25L of ADVA SBR mixed with 50kg of O.P cement will give a creamy slurry which will cover 15-40m² depending on the surface texture
and thickness applied).
MIXING RATIO
For normal use with cement sand screed, the standard mixing ratio of 10L of ADVABOND SBR per 50kg of Portland cement is recommended.
HEALTH & SAFETY

As with all Bitumen products caution should always be exercised. Protective clothing such as gloves and goggles should be worn. Treat any splashes
to the skin or eyes immediately with fresh water. Should any of the products be accidentally swallowed, do not induce vomiting call for medical
assistance immediately. Ensure that the container is available for medical attendant to examine any relevant instructions and content details.
STORAGE
Should be stored above the freezing temperature in sealed containers, away from direct flames and sunlight. In tropical climates, store in air condition
rooms.
SHELF LIFE
Up to 12 months if stored as per recommendations. Excessive exposure to sunlight and UV will result in the deterioration of the quality of the product
and reduce its shelf life.
TECHNICAL SPECIFICATIONS
PROPERTIES VALUES TEST STANDARDS

Color and Appearance White Milky Liquid -
pH 8.5-10 -
Density, [g/cc] 1.0±0.05 ASTM 1475
SBR modified mix [w/c: 0.45 and 350 kg cement]
Compressive strength, [N/mm²] >40 ASTM C 579
Flexural strength, [N/mm²] >12 ASTM C 580
Tensile strength, [N/mm²] >6 ASTM C 307
Shear bond strength, [N/mm²] >5 ASTM C 882
Application temperature, [°C] 5 to 45 -
Service temperature, [°C] -5 to 45 -
Standards ASTM C 1059
All values given are subject to 5-10% tolerance.
The information given in this datasheet is based on both current

development work and many years of field experience. Whilst every
effort is made to ensure that the information is reliable, we cannot Al Mutathawir Insulation Materials Industries L.L.C.
accept responsibility for any work carried out with our materials as T: +971 6 5345585 | F: +971 6 5347717
E: [email protected] | W: www.aim-insu.com
we have no control over methods of application, site, conditions, etc. P.O. Box: 22704,Sharjah-UAE

Advabond SBR TDS

Uploaded by

Copyright:

Available Formats

Advabond SBR TDS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Advabond SBR TDS

Uploaded by

Copyright:

Available Formats

ADVABOND SBR

SBR based bonding agent and admixture

Waterproofing internally: basements, swimming pools, potable water

Waterproofing externally: structures above ground.

Waterproof bonding: bricks slips, copings, precast treads and risers.

Waterproofing suspended floors: patios, walkways, balconies, wet areas,

Waterproof/protective slurries: potable water tanks, sewerage and mild

Al Mutathawir Insulation Materials Industries L.L.C.

HEALTH & SAFETY

PROPERTIES VALUES TEST STANDARDS

The information given in this datasheet is based on both current

You might also like