Name: ______________________________________ Date: ________________________

Student Exploration: Laser Reflection

Vocabulary: angle of incidence, angle of reflection, laser, law of reflection, plane mirror,
reflection

Prior Knowledge Questions (Do these BEFORE using the Gizmo.)

Imagine you shine a flashlight directly at a mirror, as shown below.

1. Draw an arrow showing the direction 2. Suppose you tilt the mirror. Draw an
you think the beam of light will most arrow showing the direction the beam
likely reflect off the mirror. will most likely reflect off the mirror now.

Gizmo Warm-up
Flashlights produce wide beams of light that
have various wavelengths. A laser, on the other
hand, is a narrow beam of light with only one
wavelength. All the waves in a laser beam are
parallel to one another. As a result, lasers are
ideal for studying reflection, or how waves
bounce off a surface.

Using the Laser Reflection Gizmo, you can

adjust the position of a laser beam and mirror to
study how light behaves when it is reflected.

1. Drag the Angle slider back and forth. Describe what happens to the reflected laser beam:

The reflection of the laser beam changes its direction , and reflects in different angles
_________________________________________________________________________

_________________________________________________________________________

2. Drag the laser up and down. Describe what happens to the reflected laser beam: ________
The angle of the reflection does not change , only its position does
_________________________________________________________________________

2019
 Get the Gizmo ready:
Activity A:
 Set the Laser location to 0 cm.
Reflection from a
 Set the Angle to 25 degrees.
plane mirror
 Make sure Plane mirror is selected.

Introduction: A plane mirror is a perfectly flat, smooth surface. In this activity, you will study
how plane mirrors reflect light.

Question: How does the angle of a mirror determine the angle of the reflected light?

1. Observe: Turn on Show normal. The normal is the dotted line perpendicular to the mirror.
The angle of incidence (θi) is the angle between the incoming laser beam and the normal.
The angle of reflection (θr) is the angle between the reflected laser beam and the normal.

Move the Angle slider back and forth. What do you notice about the sizes of θi and θr?

θ i size is proportional to the size of the θ r

_________________________________________________________________________

2. Measure: Set the Angle to 40 degrees and turn on Show protractor. Each marking on the
protractor represents 10 degrees.
40 40
What do θi and θr equal? θi = ____________ θr = ____________

3. Make a rule: What is the relationship between θi and θr? ____________________________

The law of reflection states that the angle of incidence is equal to the angle of reflection.
_________________________________________________________________________

Turn on Show angles and move the Angle slider back and forth. Was your rule correct?

yes
_________________________________________________________________________

The law of reflection states that the angle of incidence is equal to the angle of reflection.

4. Gather data: Use the Gizmo to complete the table below.

Mirror angle Angle of incidence (θi) Angle of reflection (θr)

0° 0 0
25° 25 25
50° 50 50

5. Make a rule: How is the mirror angle related to the angles of incidence and reflection?
The mirror angle and the angles of incidence and reflection are the same
_________________________________________________________________________

2019
 Activity B:
Get the Gizmo ready:
Reflection from
 Turn off Show normal and Show protractor.
non-planar
 Set the mirror Angle to 50°.
mirrors

Question: How can you use the angle of refraction to determine the shape of a non-
planar mirror’s surface?

1. Observe: Turn on Insert beam splitter. How do the seven incoming beams compare with
one another? How do the reflected beams compare with one another?
The seven incoming beams are parallel to one another. The reflected beams are also parallel to
_________________________________________________________________________
one another.
_________________________________________________________________________

2. Observe: From the dropdown menu at lower right, select Mirror 1. Unlike the plane mirror,
mirror 1 is not flat.

A. Describe how the laser beams changed: ___________________________________

It converges (which the plane one doesnt)
___________________________________________________________________

B. Why do you think this happened? ________________________________________

On mirror 1, the ray converges towards it. with the plane mirror, the ray passes straight through
___________________________________________________________________

___________________________________________________________________

3. Solve: Turn off Insert beam splitter. Set the mirror’s Angle to 0 degrees and the Laser
location to 35 cm. Check that Show angles is on.
3.5. 3.5
A. What are the angle of incidence and angle of reflection (θi and θr)? ______________

B. What does this tell you about the surface of the mirror in this location? ___________
concave (or convex i forgot the term)
___________________________________________________________________
pretty sure its concave
C. Move the Laser location to 14 cm. How did the orientation of the beam change?
switched to the top
___________________________________________________________________

D. What does this tell you about the surface of the mirror in this location? ___________
convex
___________________________________________________________________

(Activity B continued on next page)

2019
Activity B (continued from previous page)

4. Summarize: What does it mean if the reflected beam is above the incident beam? What
does it mean if the reflected beam is below the incident beam?

_________________________________________________________________________

_________________________________________________________________________

5. Collect data: You will now use the laser to 6. Draw: Use the data you collected to create
map the surfaces of mirrors 1, 2, and 3. In drawings of the mirrors’ surfaces in the
the rows of the table, record each mirror’s boxes below. Be sure to pay attention to
angle at all the listed locations. If the beam negative signs, which indicate the direction
is deflected downward, the angle is of the angle.
negative. Otherwise the angle is positive.

Mirror 1 Mirror 2 Mirror 3

Height Mirror 1 Mirror 2 Mirror 3
Angle Angle Angle
35 cm
30 cm
25 cm
20 cm -
15 cm 5

10 cm
5 cm
0 cm
-5 cm
-10 cm
-15 cm
-20 cm
-25 cm
-30 cm
-35 cm

7. Analyze: Does the law of reflection hold true for mirrors that aren’t flat? Use the Gizmo to
explore this question, and describe your findings.
The law of reflection holds true for all mirror irrespective of their shape or size.
_________________________________________________________________________

_________________________________________________________________________

2019