Scribd
Upload
326 views3 pages

Sample Question Paper

The document contains sample questions for a mechanical engineering materials exam divided into 6 topics. The questions cover various materials engineering concepts including properties of metals, alloys, polymers, and heat treatment processes. Correct answers are provided for multiple choice questions testing knowledge of materials and engineering applications.

Uploaded by

chavanomkar9363
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
326 views3 pages

Sample Question Paper

The document contains sample questions for a mechanical engineering materials exam divided into 6 topics. The questions cover various materials engineering concepts including properties of metals, alloys, polymers, and heat treatment processes. Correct answers are provided for multiple choice questions testing knowledge of materials and engineering applications.

Uploaded by

chavanomkar9363
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Sample Questions for 22343 - (Mechanical Engineering Materials)

Topic-1
1) The Brinell hardness number is calculated by dividing the
a) applied load with the surface area of the indentation.
b) surface area of the indentation with applied load.
c) applied load with depth of the indentation.
d) depth of the indentation with diameter of indentor

2) This equation is atomic radius of _________

a) BCC lattice
b) FCC lattice
c) HCP lattice
d) Simple Cube

3) In Optical microscope the prism reflector is so positioned that only about _________ of the area of the
objective aperture is obstructed.
a) 1/2
b) 1/3
c) 1/4
d) 2/3

Topic-2
4) Identify element from the following, which should be added in alloy steel to increase creep strength at
high temperature.
a) Titanium
b) Silicon
c) Molybdenum
d) Vanadium

5) Choose type of stainless steel from the following which is used to make heating elements for furnace.
a) Austenitic stainless steel
b) Martensitic stainless steel
c) Ferritic stainless steel
d) None of the above

6) Identify the meaning of following specification of steel


X10cr18ni9s3
a) High Alloy Steel, 0.10%C, 18%Cr, 9%Ni, Pickled Condition
b) High Alloy Steel, 1.0%C, 18%Cr, 0.9%Ni, Pickled Condition
c) High Alloy Steel, 0.10%C, 1.8%Cr, 9%Ni, Pickled Condition
d) High Alloy Steel, 1.0%C, 1.8%Cr, 0.9%Ni, Pickled Condition
Topic -3

7) Annealing temperature range for hypoeutectoid steel is


a) Upper critical temperature +50 ºc
b) Upper critical temperature +250 ºc
c) Lower critical temperature +50 ºc
d) Below lower critical temperature

8) Ductile cast iron ASTM A536 contains


a) C=3.5-5.9%
b) C=3.5-3.9%
c) C=3.5-6.9%
a) C=3.5-4.9%

9) Cast iron pipes are mainly used.


a) for conveying steam
b) in water and sewage systems
c) in pressure lubrication systems on prime movers
d) all of the above

Topic-4
10) In porous bearing , oil which is forced from the loaded zone of the bearing is reabsorbed by ----------
a) Gravitational force
b) Centrifugal force
c) Capillary action
d) Magnetic action

11) ---------- is an alloy made up of 90% Aluminium, 4% Copper, 0.5-1% Magnesium, and less than 1%
Manganese
a) Y alloy
b) Bronze
c) Duralumin
d) Hindalium

12) If weights are same, the electrical conductivity of aluminum is ---------- conductor than copper.
a) Higher
b) Lower
c) Equal
d) Zero
Topic-5
13) Polymethtyle Methacrylate is used in -------------
a) Bottles
b) Ropes
c) Brush Bristles
d) Brush Bristles

14) ________Is not thermosetting material?


a) Vinyls
b) Epoxides
c) Bakelites
d) Malemines

15) ______Discolours on ageing by sunlight


a) Nylons
b) Phenol formaldehyde
c) Acrylic
d) Abs

Topic-6
16) Annealing temperature range for hypoeutectoid steel is
a) Lower critical temperature +50 ºc
b) Below lower critical temperature
c) Upper critical temperature +50 ºc
d) Upper critical temperature +250 ºc

17) Guide-ways of Lathe are hardened by______


a) Annealing
b) Normalizing
c) Tempering
d) Hardening

18) Formation of thick layer of scale on the surface of steel articles can be minimised by
a) Heating in furnaces with reducing neutral or protective atmosphere
b) Heating in boxes with used carburising agent or cast iron chips
c) Heating in molten salt bath
d) Any of the above

You might also like