MEAN WELL COLOMBIA

Centro Empresarial Blue G.

Telefono: 018000-510117 / Whatsapp: 316-5290052
[email protected] / Barranquilla- Colombia
CSP-3000 series
3000W Power Supply with Single Output User’s Manual Video


    
      
      
 


■  ■ 
‧ ‧
‧ ‧
‧ ‧
‧ ‧
‧ ‧
‧ ‧
‧ ■ 
  
‧

‧
‧1

■ 


℃



■ 
    





File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series
SPECIFICATION
MODEL CSP-3000-120 CSP-3000-250 CSP-3000-400
DC VOLTAGE 120V 250V 400V
RATED CURRENT 25A 12A 7.5A
CURRENT RANGE 0 ~ 25A 0 ~ 12A 0 ~ 7.5A
RATED POWER 3000W 3000W 3000W
RIPPLE & NOISE (max.) Note.2 800mVp-p 1000mVp-p 1200mVp-p
OUTPUT CONSTANT CURRENT REGION 90 ~ 120V 125 ~ 250V 200 ~ 400V
VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.5% ±0.5%
LOAD REGULATION ±0.5% ±0.5% ±0.5%
SETUP, RISE TIME 1000ms, 80ms / 230VAC at full load
HOLD UP TIME (Typ.) 10ms at full load
VOLTAGE RANGE Note.4 180 ~ 264VAC 254 ~ 370VDC
FREQUENCY RANGE 47~63Hz
POWER FACTOR (Typ.) PF≧0.95/230VAC at full load
INPUT EFFICIENCY (Typ.) 92% 92.5% 93%
AC CURRENT (Typ.) 20A/180VAC 16A/230VAC
INRUSH CURRENT (Typ.) Cold start 60A/230VAC
LEAKAGE CURRENT <0.3mA / 240VAC
SHORT CIRCUIT Shut down and latch off o/p voltage, re-power on to recover
105 ~ 120% rated output power
OVER CURRENT
User adjustable continuous constant current limiting or constant current limiting with delay shutdown after 3 seconds, re-power on to recover
PROTECTION
(Please refer to the Function Manual)
127 ~ 150V 265 ~ 315V 420 ~ 500V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down or re-power on to recover
OUTPUT VOLTAGE
Please refer to the Function Manual.
PROGRAMMABLE(PV)
OUTPUT CONSTANT CURRENT
Please refer to the Function Manual.
PROGRAMMABLE(PC)
CURRENT SHARING Please refer to the Function Manual.
FUNCTION
AUXILIARY POWER(AUX) [email protected]
REMOTE ON-OFF CONTROL Please refer to the Function Manual
ALARM SIGNAL OUTPUT Power OK signal. Please refer to the Function Manual
WORKING TEMP. -20 ~ +65℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH non-condensing
TEMP. COEFFICIENT ±0.05%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS UL62368-1,Dekra seal BS EN/EN62368-1, EAC TP TC004, GB4943.1
WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
Parameter Standard Test Level / Note
Conducted BS EN/EN55032(CISPR32) Class A
EMC EMISSION Radiated BS EN/EN55032(CISPR32) Class A
Harmonic Current BS EN/EN61000-3-2 -----
Voltage Flicker BS EN/EN61000-3-3 -----
SAFETY & BS EN/EN55035 ,BS EN/EN61000-6-2
EMC Parameter Standard Test Level / Note
(Note 5)
ESD BS EN/EN61000-4-2 Level 3, 8KV air ; Level 2, 4KV contact
Radiated BS EN/EN61000-4-3 Level 3
EFT / Burst BS EN/EN61000-4-4 Level 3
EMC IMMUNITY
Surge BS EN/EN61000-4-5 Level 3, 2KV/Line-Earth ; Level 2, 1KV/Line-Line
Conducted BS EN/EN61000-4-6 Level 3
Magnetic Field BS EN/EN61000-4-8 Level 4
>95% dip 0.5 periods, 30% dip 25 periods,
Voltage Dips and Interruptions BS EN/EN61000-4-11
>95% interruptions 250 periods
MTBF 721.1K hrs min. Telcordia SR-332 (Bellcore) ; 80.5K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 278*177.8*63.5mm (L*W*H)
PACKING 4Kg; 4pcs/16Kg/1.81CUFT
NOTE ℃






℃℃
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:CSP-3000-SPEC 2022-08-05
 3000W Power Supply with Single Output CSP-3000 series

Block Diagram PFC fosc : 85KHz

PWM fosc : 100KHz

ACTIVE RECTIFIERS RECTIFIERS

EMI INRUSH POWER +V
I/P CURRENT & SWITCHING &
FILTER PFC FILTER -V
LIMITING

PFC O.V.P.
CONTROL O.L.P.
PWM
DETECTION
O.T.P. CONTROL CIRCUIT P OK
REMOTE RC
CONTROL

PV/PC PV/PC ADJUST

CONTROL CIRCUIT PV/PC CHOSE

LOAD CS
SHARING

FAN
AUX RECTIFIERS
POWER & AUX POWER
FILTER (12V/0.4A)

Static Characteristics Derating Curve

100
100
90

80
80
LOAD (%)

LOAD (%)

70 60

60 50
40
50

20
40

180 190 200 210 220 250 264 -20 0 10 20 30 40 50 60 65 70 (HORIZONTAL)

AMBIENT TEMPERATURE (℃)

INPUT VOLTAGE (V) 60Hz

Efficiency vs Load (400V Model)

94
92
EFFICIENCY (%)

90
88
86
84
82
80
78
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD

※ The curve above is measured at 230VAC.

File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

DRIVING METHODS OF LED MODULE

※ I-V Operating Area(for PC mode only)

◎ CSP-3000-120 ◎ CSP-3000-250

130V 260V
1.36A, 250V 9A,250V
12A, 250V
125V
2.4A, 120V 15A,120V
240V
120V 25A,120V
220V
115V

110V 200V

105V 180V
17A, 176.5V
100V 30A,100V
160V
95V
140V
90V 30A,90V
2.4A, 90V 17A, 125V
85V 120V
1.36A, 125V
80V 100V
0A 5A 10A 15A 20A 25A 30A 35A 0A 3A 6A 9A 12A 15A 18A

Recommended High Performance Region Allowed Operational Region Recommended High Performance Region Allowed Operational Region

◎ CSP-3000-400

430V
0.8A, 400V 5.25A,400V 7.5A, 400V
400V
370V
340V
10A,300V
310V
280V
250V
220V
190V
0.8A, 200V 10A,200V
160V
130V
100V
0A 1.5A 3A 4.5A 6A 7.5A 9A 10.5A 12A 13.5A 15A

Recommended High Performance Region Allowed Operational Region

File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

Function Manual
1. Output Voltage/Current Programming
※ Mode Setting
CN1:
CONDITION MODE FUNCTION

SHORT PV MODE Output Voltage Programming

PIN5/PIN6
OPEN PC MODE Output Current Programming

※ The factory default settings:PV mode output max voltage pin5/pin6 short by jumper cap.
When pull out the jumper cap,the default settings: PC mode output max constant current.

PIN6
PIN5
PV/PC MODE CHOSE

CN1

PV/PC SET(SVR2)
max.

PIN6
PIN5 PV/PC ADJUST

CN2

※ PV/PC Set adjustment

◎ Adjust the resistance(SVR2) can set output voltage or constant current point, the adjusting range is 20%-100% of max voltage or max
constant current point.
◎ In the CN2, pin5/pin6 access external 10V voltage signal or 500-1KHz PWM signal can adjust the output voltage or constant current point.
CN2:PIN5/PIN6
needs
to
operate
with
a
10V
sinking
signal
or
PWM signal,Max.
sink
current
1mA.

Vout Iout

100 100
CURRENT ADJUSTMENT /(%)
VOLTAGE ADJUSTMENT /(%)

80 80
Non-Linear Non-Linear
60 60

40 40

15
8

1.5 4 6 8 10 V 0.8 4 6 8 10 V
15 40 60 80 100 % 8 40 60 80 100 %

PIN5/PIN6 ACCESS TO EXTERNEL VOLTAGE SIGNALS(DC/PWM) PIN5/PIN6 ACCESS TO EXTERNEL VOLTAGE SIGNALS(DC/PWM)

MODEL 120V 250V 400V

PV range 18 ~ 120V(max.) 37.5 ~ 250V(max.) 60 ~ 400V(max.)

PC range 2.4 ~ 30A(max.) 1.4~ 17A(max.) 0.8 ~ 10A(max.)

File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

2.Remote ON-OFF
※ Remote ON-OFF is activated by the configuration with respect to CN1 as shown in the following diagram.

PIN3 RC
PIN1 RCG
CN1

Example 2.2(A): Using external voltage source

AUX

1KΩ 12V
RC
Internal
12V typ.
SW
RCG

AUXG

Example 2.2(B): Using internal 12V auxiliary output

AUX

1KΩ RC
Internal
12V typ.
RCG

SW

AUXG

Example 2.2(C): Using internal 12V auxiliary output

AUX

1KΩ
1KΩ RC
Internal
12V typ. SW

RCG

AUXG
◎ Connection Method
Example 2.2(A) Example 2.2(B) Example 2.2(C)
Power supply output ON SW Open(open) SW Open(open) SW Close(short)
SW Logic
Power supply output OFF SW Close(short) SW Close(short) SW Open(open)

File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

3.Alarm Signal Output

※ Alarm signal is sent out through "P OK" & "P OK GND" and P OK2 & P OK GND2 pins on CN1. Please acknowledge an external voltage source is required for this function.

PIN9(P-OK-GND) PIN4(P-OK-GND-2)
PIN7(P-OK) PIN2(P-OK-2)

CN1

Function Description Output of alarm(P OK, Relay Contact) Output of alarm(P OK2, TTL Signal)
The signal is "Low" when the power supply is above Low Low
80% of the rated output voltage, or, say, Power OK (0.5V max at 500mA) (0.5V max at 10mA)
P OK
The signal turns to be "High" when the power supply
High or open High or open
is under 80% of the rated output voltage, or, say,
(External applied voltage, 500mA max.) (External applied voltage, 10mA max.)
Power Fail

Table 3.1 Explanation of alarm

P OK P OK2

R R
V 0.1uF V

P OK GND External voltage and R P OK GND2 External voltage and R

(The max. sink is 500mA and 20V) (The max. sink is 10mA and 30V)

Fig. 3.2 Internal circuit of P OK (Relay, total is 10W) Fig. 3.3 Internal circuit of P OK2 (Open collector method)

4.Select Overload Protection Type

(1)Insert the shorting connector on CN1 that is shown in Fig 4.1, the Overload Protection Type will be "constant current limiting with delay shutdown after 3 seconds,
re-power on to recover". This is the factory default.
(2)Remove the shorting connector on CN1 that is shown in Fig 4.2, the Overload Protection Type will be "continuous constant current limiting".

PIN5 PIN5

PIN6 PIN6

Fig. 4.1 Insert the CN1 Fig. 4.2 Remove the CN1
Overload Protection Type : constant current limiting with delay shutdown after 3 seconds Overload Protection Type : constant current limiting

File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

5.Current Sharing
CSP-3000 has the built-in active current sharing function and can be connected in parallel, up to 3 units, to provide higher output power as exhibited below :
※ The power supplies should be paralleled using short and large diameter wiring and then connected to the load.
※ Difference of output voltages among parallel units should be less than 0.2V(Can Fine tune by SVR1).
※ The total output current must not exceed the value determined by the following equation:
Maximum output current at parallel operation=(Rated current per unit)×(Number of unit)×0.9
※ When out current<( 50% rate current)×(Number of unit),
the current shared among units may not be fully balanced.

◎ CS+/CS- on CN1 are connected mutually in parallel(Note:CS+/CS- do not reverse connection).

◎ Under parallel operation, the "PV/PC" function is not available.

Current Sharing condition

No.1(Master)
max. Output Voltage ADJ(SVR1)

+V

-V

+V
No.2(Slave) Load
-V

+V

-V

No.3(Slave)

+V

-V

File Name:CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

Mechanical Specification
Case No.982B Unit:mm
278
236.3 27

12.5

63.5
CN1 CN2

38
1 1
10 8 6 4 2 8642

8-M4(Both Sides) L=5mm

9 7 53 1 7531

236.3 27 19max.

7.9
4-M4 L=5mm

16
1 1

13
OUTPUT

177.8
Air flow

162
direction

INPUT

10
13
1 1

16max.

※ Mounting Instruction Chassis of CSP-3000

Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended mounting torque Mounting Surface
1 M4 5mm 7~10Kgf-cm

※ Control Pin No. Assignment (CN1) : HRS DF11-10DP-2DS or equivalent

Mounting Screw

Mating Housing HRS DF11-10DS or equivalent L

9 10
Terminal HRS DF11-**SC or equivalent

1 2

Pin No. Function Description

1 RCG Remote ON-OFF Ground
2 P-OK-2 Power OK Signal(TTL Signal)
3 RC Remote ON-OFF
4 P-OK-GND-2 Power OK Ground
5 GND PV/PC Mode Choose Ground
6 Mode PV/PC Mode Choose
7 P-OK Power OK Signal(Relay Contact)
8 CS+ Current Sharing Signal+
9 P-OK GND Power OK Ground
10 CS- Current Sharing Signal-

File Name: CSP-3000-SPEC 2022-08-05

 3000W Power Supply with Single Output CSP-3000 series

※Control Pin No. Assignment (CN2) : HRS DF11-8DP-2DS or equivalent

7 8
Mating Housing HRS DF11-8DS or equivalent
1 2 Terminal HRS DF11-**SC or equivalent

Pin No. Function Description

1 12V AUXG Auxiliary output GND
2 12V AUX+ Auxiliary output+
3 NC
4 NC
5 PV/PC+ PV/PC adjust+
6 PV/PC- PV/PC adjust-
7 NC
8 NC
Note: NC pins, please keep open circuit and do not connect to other pins/signals.

※LED status indication

LED LED Signal Description

Green LED nornal Power supper working normllly

Green LED slow flash

Standby power supply(Remote off)
（Cycle1.4S）

Red LED of flash

Power OVP , output voltage too low
（Cycle200mS）

Red LED slow flash NTC fault, power OTP, temperature

（Cycle1.4S） switch action

Red LED nornal Power fan fault

Red LED of flash
（Cycle 200mS） Line fault,CN2 pin7/8 signal abnormal
Green LED of flash

※AC Input Terminal Pin No. Assignment

Pin No. Assignment Diagram Maximum mounting torque
1 AC/L
2 AC/N 18Kgf-cm
3 FG

※DC Output Terminal Pin No. Assignment

Pin No. Assignment Diagram Maximum mounting torque
1 V-
18Kgf-cm
2 V+

Installation Manual
Please refer to : http://www.meanwell.com/manual.html

File Name: CSP-3000-SPEC 2022-08-05