VPI SERIES

Pressure Independent Control Valves and Actuators

VPI series PICV and actuators make it simple

to achieve 100% control of the water flow in
the building while creating high comfort and
energy savings at the same time. An additional
benefit is that no balancing is required if
further stages are added to the system, or
even if the dimensioned capacity is changed.
Honeywell’s VPI series provides modulating
control with full authority regardless of
pressure fluctuations in the system.

APPLICATION ALL-IN-ONE APPROVALS

Designed to use in heating and It combines an externally adjustable Shut-off leakage as per ANSI / FCI 70-2
cooling systems such as Air Handling automatic balancing valve, a 206 / IEC 60534-4 - Class IV/ 0.01%
Units, Fan Coil Units, and other differential pressure control valve and, leakage of full open valve capacity.
central plant applications. a full authority modulating control Tested as per BSRIA standards.
valve in a single unit. It combines UL & CE approved actuators.
EASY SETTING & FIELD 3 functions into one valve body:
ADJUSTABLE FLEXIBLE
• Control valve
Flow setting is step-less and can easily • Differential pressure controller that Two-way, modulating to accept
be set to any design flow in the flow protects against pressure fluctuations digital or analog input signals. The
range. Setting can be done before • Presetting scale to set the valves accept 0(2)-10V, 3-point
or after installation and flow may be desired maximum flow floating or ON/OFF input signals.
changed on demand without removing
the valve from the installation. SEALED SETTING HIGHER PRESSURE RANGE
Actuator will cover the setting and • Differential pressure operating
COMPACT DESIGN protect against tampering. range up to 800 kPaD
Compact one-unit PICV, including • Close-off pressure range
modulating control valve, dynamic FLEXIBLE SETTINGS up to 800 kPa
flow limiter and, differential pressure Higher presetting precision due
control valve in one body. to step-less analog scale with 41
STEADY FLOW
Maximum flow setting through Flow balancing in valve body
the dial on the valve body. through diaphragm.

FEATURES AND BENEFITS

Available in DN female Energy saving due Simple Maintenance Controls chilled or Electrical actuators
threaded (ISO) sizes to optimal control, – Internal parts can hot water in closed with selectable control
varying from DN15-50 lower flow, and pump be accessed without loop systems with modes, Linear or Equal
with or without pressure. removing the valve up to 50% glycol. percentage settings.
pressure test ports. Maximized T due housing from the
to faster response piping lines
and increased
system stability.
TECHNICAL SPECIFICATIONS
VALVE SPECIFICATION
PARAMETER SPECIFICATIONS

Valve Type: Pressure Independent Control Valve

Body Style: Globe / Linear

Size Range: DN15 - DN50 (1/2” - 2”)

PN Pressure Rating: PN25

Static Pressure: 2500 kPa / 360 psi

Ambient Temperature: +1ºC to +50ºC / +34ºF to +122ºF

Medium Temperature: -20ºC to +120ºC / -4ºF to +248ºF

Maximum Close-Off Pressure: 800 kPa / 116 psi

DN15 – DN32: 800 kPaD / 116 psid

Maximum Operational P: DN40 - DN50: 600 kPaD / 87 psid

Flow Characteristic: Linear, can be converted to equal percentage in the actuator

Shut-Off Leakage: ANSI / FCI 70-2 206 / IEC 60534-4 - Class IV/ 0.01% leakage of full open valve capacity

Control Range: 1:1000 / IEC 60534

Rangeability: 100:1

Turn Down Ratio: 100:1

DN15 - DN25: 3.4 mm (0.13”)

Stroke: DN32: 5.2 mm (0.2”)
DN40 - DN50: 6.2 mm (0.24”)

DN15LF - DN20LF: 64 to 1110 l/hr

DN15HF - DN25HF: 620 to 2650 l/hr
Maximum Flow Rate Setting: DN32: 865 to 4630 l/hr
DN40 - DN50: 1900 to 13647 l/hr

CONSTRUCTION

SPECIFICATIONS
COMPONENT
DN15-DN32 DN40-DN50

Valve Housing: DZR Brass ASTM CuZn36Pb2As Ductile iron ASTM A395 Grade 60-40-18

Flow Regulator: Glass-reinforced PSU/POM/PPS Glass-reinforced PSU/POM/PPS

Cone: PPS Stainless Steel

Diaphragm: EPDM/Hydrogenated acrylonitrile-butadiene-rubber Hydrogenated acrylonitrile-butadiene-rubber

O-rings and Seat: EPDM EPDM

Head Nut: Forged brass ASTM CuZn40Pb2 --

Thread Connection: Fixed female ISO Fixed female ISO

Housing Taps: 1/4” ISO 1/4” ISO

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 2

MEASUREMENTS AND DIMENSIONS
DN15-DN32 SIZE VALVES

H6

H2 H3 H4 H6
MM (IN) MM (IN)
MM (IN) MM (IN)
VALVE L H1 WEIGHT1
MODEL NO. MLP71MAA, MLE75MAB
SIZE MM (IN) MM (IN) KG (LB)
MLP71TNA MLP41TNA MLP71MNA, & &
MLE71MAA MLP75MAB
VPI015TWL2 15 (1/2) 81 (3.19) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.50 (1.11)

VPI015TPL2 15 (1/2) 81 (3.19) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.50 (1.11)

VPI015TWH2 15 (1/2) 81 (3.19) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.50 (1.11)

VPI015TPH2 15 (1/2) 81 (3.19) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.50 (1.11)

VPI020TWL2 20 (3/4) 85 (3.35) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.52 (1.14)

VPI020TPL2 20 (3/4) 85 (3.35) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.52 (1.14)

VPI020TWH2 20 (3/4) 85 (3.35) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.52 (1.14)

VPI020TPH2 20 (3/4) 85 (3.35) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.52 (1.14)

VPI025TWH2 25 (1) 102 (4.02) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.72 (1.59)

VPI025TPH2 25 (1) 102 (4.02) 31 (1.22) 118 (4.65) 116 (4.57) 124 (4.88) - 0.72 (1.59)

VPI032TWH2 32 (1 1/4) 128 (5.04) 47 (1.85) 138 (5.43) 137 (5.39) 144 (5.67) - 1.70 (3.75)

VPI032TPH2 32 (1 1/4) 128 (5.04) 47 (1.85) 138 (5.43) 137 (5.39) 144 (5.67) - 1.70 (3.75)

VPI040TPH2 40 (1 1/2) 191.0 (7.5) 100.2 (3.9) - - - 194.7 (7.7) 4.3 (9.5)

VPI050TPL2 50 (2) 191.0 (7.5) 100.2 (3.9) - - - 194.7 (7.7) 3.8 (8.4)

Note 1: Weight does not include an actuator.

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 3

MLP71MAA ACTUATORS (FAIL-IN-PLACE)
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Modulating Power Consumption: Wire Connection:
Supply Voltage: 24V AC/DC ±10%, 24V AC: 2.5VA operating (4.7VA max.) Fixed, 5 wires x 0.50 mm2, 1.5 meter cable
50/60 Hz 24V DC: 1.2W operating (2.2W max.) CE Conformity: EN 60730
Failsafe Function: No Ambient Temperature: 0°C to +50°C Protection Rating: IP54 incl. upside-
Control Signal: Analog 0(2)-10V DC, (+32°F to +122°F) down, class III, indoor use only
<0.5mA Media temperature: 0°C to +120°C Weight: 0.25 kg / 0.55 lb
Feedback: Yes, control signal (+32°F to +248°F) Valve Size Compatibility: DN15 - DN32
Actuating Force: High (250N -30N/+70N) Humidity rating: 0-85% RH, no Override: Yes, Electrical
Stroke: 5.8 mm / 0.23 in (compensated) condensation
Operation Time: 22 sec/mm Position Indicator: Yes

MEASUREMENTS & DIMENSIONS WIRING CONNECTIONS

MLP71MAA
0(2)-10V modulating

Green
Brown

Yellow
Grey
Blue
Input signal
0(2)-10V DC Feedback signal
<0.5mA 0(2)-10V DC
Power 24V AC/DC

Ground/common
Signal Ground

L W H WEIGHT
ACTUATOR T
MM (IN) MM (IN) MM (IN) KG (LB)
MLP71MAA 86.5 (3.41) 48.5 (1.91) 80 (3.15) M30x1.5 0.25 (0.55)

ACTUATOR SWITCH FUNCTIONS

SWITCH FACTORY
SWITCH FUNCTION
NUMBER SETTINGS
Auto cycle ON/OFF
If the plant specifications permit it, the auto cycle can be activated during
commissioning. Auto cycle prevents the valve from jamming when the
Switch 1 valve is not moved for a longer period of inactivity, e.g. for heating systems OFF
during the summer. When the auto cycle is activated, the actuator will
perform 50% stroke cycle if no stroke movement has occurred during a
3-week period.
Analog 2-10V DC / 0-10V DC
Switch 2 Setting control range by the continuous actuating signal 0-10V DC or 0-10V DC
2-10V DC.
Normally open / Normally closed Normally closed;
Switch 3 Setting actuating direction with 10V DC control signal to “valve open” or 0V DC = valve
“valve closed” as well as the position feedback. closed Actuator Switch Function
Equal % control / Linear control
Switch 4 Setting of actuating control curve to either equal percentage or linear Linear control The valve functions are adjusted with the DIP
control. switches under the connection cover.
Switch 5 No function. Close
Electrical override
Setting override function to ON and the actuator will open valve fully.
When set to OFF again, the actuator will re-calibrate and thereafter go into Off
Switch 6
normal operation mode.

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 4

MLP71MNA ACTUATORS (FAIL-IN-PLACE)
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Modulating Power Consumption: Wire Connection: Fixed, 3 wires x 0.50
Supply Voltage: 24V AC/DC ±15%, 24V AC: 2.5VA operating (4.7VA max.) mm2, 1.5 meter cable
50/60 Hz 24V DC: 1.2W operating (2.2W max.) CE Conformity: EN 60730
Failsafe Function: No Ambient Temperature: 0°C to +50°C Protection Rating: IP54 incl. upside-
Control Signal: Analog 0(2)-10V DC, (+32°F to +122°F) down, class III, indoor use only
<0.5mA Media temperature: 0°C to +120°C Weight: 0.25 kg / 0.55 lb
Feedback: No (+32°F to +248°F) Valve Size Compatibility: DN15 - DN32
Actuating Force: 160N -10N/+70N Humidity Rating: 0-85% RH, no Override: Yes, Electrical
Stroke: 5.8 mm / 0.23 in (compensated) condensation
Operation Time: 22 sec/mm Position Indicator: Yes

MEASUREMENTS & DIMENSIONS WIRING CONNECTIONS

MLP71MNA
0(2)-10V modulating

Brown

Grey
Blue
Input signal
0(2)-10V DC
<0.5mA
Power 24V AC/DC

Ground/common

L W H WEIGHT
ACTUATOR T
MM (IN) MM (IN) MM (IN) KG (LB)
MLP71MNA 86.5 (3.41) 48.5 (1.91) 80 (3.15) M30x1.5 0.25 (0.55)

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 5

MLP75MAB ACTUATORS
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Floating / Modulating Stroke: 7 mm / 0.276 in Position Indicator: Yes
(universal) Operation Time: 22 sec/mm Wire Connection: Fixed, 5 wires x 0.50
Supply Voltage: 24V AC/DC ±10%, 50/60 Power Consumption: mm2, 1.5 meter cable
Hz 24V AC: 6VA operating (8.5VA max.) CE Conformity: EN 60730
Failsafe Function: No 24V DC: 2.6W operating (4.1W max.) Protection Rating: IP54 incl. upside-
Control Signal: Analog 0(2)-10V DC, Ambient Temperature: 0°C to +50°C down, class III, indoor use only
<0.5mA or digital 3-point floating and ON/ (+32°F to +122°F) Weight: 0.30 kg / 0.67 lb
OFF Media Temperature: 0°C to +120°C Valve Size Compatibility: DN40 – DN50
Feedback: Yes, control signal (analog) or (+32°F to +248°F) Override: Manual
0-10V DC (digital ON/OFF) Humidity Rating: 0-85% RH, no
Actuating Force: 600N -50N/+100N condensation

MEASUREMENTS & DIMENSIONS WIRING CONNECTIONS

MLP75MAB Actuator
0(2)-10V modulating

Yellow
Brown

Green
Grey
Blue
Input signal Feedback signal
0(2)-10V DC 0(2)-10V DC
<0.5mA
Power 24V AC/DC

Ground/common
Signal ground

MLP75MAB Actuator MLP75MAB Actuator M

0(2)-10V modulating 2-Position, Normally Closed 3-Point

Yellow
Brown

Green
Yellow
Brown

Green

Grey

Blue
Blue
Grey
Blue

Input signal Feedback signal Feedback signal

0(2)-10V DC 0(2)-10V DC Close Open 0-10V DC Clo
<0.5mA
Power 24V AC/DC
L W H WEIGHT
Power 24V AC/DC
ACTUATOR T
MM (IN) MM (IN) MM (IN) KG (LB)
Ground/common Ground/common
Signal ground Signal ground
MLP75MAB 96.0 (3.78) 56 (2.20) 91 (3.58) M30x1.5 0.30 (0.67)

MLP75MAB Actuator MLP75MAB Actuator

2-Position, Normally Closed 3-Point Floating, Normally Closed
ACTUATOR SWITCH FUNCTIONS
Yellow
Brown
Yellow
Brown

Green
Green

SWITCH FACTORY
Grey
Grey

Blue
Blue

SWITCH FUNCTION
NUMBER SETTINGS
Feedback signal Stop Feedback signal
Close Open 0-10V DC Close Open 0(2)-10V DC
Auto cycle ON/OFF
If the plant specifications permit it, the auto cycle can be activated during
commissioning. Auto cycle prevents the valve from jamming when the Power 24V AC/DC Power 24V AC/DC
Switch 1 valve is not moved for a longer period of inactivity, e.g. for heating systems OFF
during the summer. When the auto cycle is activated, the actuator will Ground/common Ground/common
perform 50% stroke cycle if no stroke movement has occurred during Signal ground
a Signal ground
3-weeks period.
Analog 2-10V DC / 0-10V DC
Switch 2 Setting control range by the continuous actuating signal 0-10V DC or 0-10V DC
2-10V DC.
Normally open / Normally closed Normally
Switch 3 Setting actuating direction with 10V DC control signal to “valve open” or closed; 0V DC
“valve closed” as well as the position feedback. = valve closed
Equal % control / Linear control
Switch 4 Setting of actuating control curve to either equal percentage or linear Linear control
control.
Switch 5 No function. Close
Re-calibration
Switch 6 Setting is in different but flipping the switch will start re-calibration. After Off
re-calibration the actuator will automatically go into normal operation.

Actuator Switch Function

The valve functions are adjusted with the DIP
switches under the connection cover.
VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 6
MLE71MAA ACTUATORS
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLE series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Modulating Operation Time: 22 sec/mm (failsafe Wire Connection: Fixed,
Supply Voltage: 24V AC/DC ±10%, mode: 5 sec/mm) 5 wires x 0.50 mm2, 1.5 meter cable
50/60 Hz Power Consumption: CE Conformity: EN 60730
Failsafe Function: Yes, optional open or 24V AC: 5.8VA operating (6.8VA max.) Protection Rating: IP54 incl. upside-
close 24V DC: 2.9W operating (3.3W max.) down, class III, indoor use only
Control Signal: Analog 0(2)-10V DC or Ambient Temperature: 0°C to +50°C Weight: 0.27 kg / 0.60 lb
digital 2-position with constant power (+32°F to +122°F) Valve Size Compatibility: DN15 - DN32
supply Media temperature: 0°C to +120°C Override: Yes, Electrical
Feedback: Yes, control signal (analog) or (+32°F to +248°F)
0-10V DC (digital) Humidity rating: 0-85% RH, no
Actuating Force: High (250N -30N/+70N) condensation
Stroke: 5.8 mm / 0.23 in (compensated) Position Indicator: Yes

MEASUREMENTS & DIMENSIONS WIRING CONNECTIONS

MLE71MAA Actuator
0(2)-10V modulating

Yellow
Brown

Green
Grey
Blue
Input signal Feedback signal
0(2)-10V DC 0(2)-10V DC
<0.5mA
Power 24V AC/DC

Ground/common
Signal ground

MLE71MAA Actuator
2-Position, Normally Closed

Yellow
Brown

Green
Grey
Blue

Feedback signal
Close Open 0-10V DC

L W H WEIGHT Power 24V AC/DC

ACTUATOR T
MM (IN) MM (IN) MM (IN) KG (LB) Ground/common
Signal ground
MLE71MAA 86.5 (3.41) 48.5 (1.91) 80 (3.15) M30x1.5 0.27 (0.60)

ACTUATOR SWITCH FUNCTIONS

SWITCH FACTORY
SWITCH FUNCTION
NUMBER SETTINGS
Auto cycle ON/OFF
If the plant specifications permit it, the auto cycle can be activated during
commissioning. Auto cycle prevents the valve from jamming when the
Switch 1 valve is not moved for a longer period of inactivity, e.g. for heating systems OFF
during the summer. When the auto cycle is activated, the actuator will
perform 50% stroke cycle if no stroke movement has occurred during a
3-weeks period.
Analog 2-10V DC / 0-10V DC
Switch 2 Setting control range by the continuous actuating signal 0-10V DC or 0-10V DC
2-10V DC.
Normally open / Normally closed Normally
Switch 3 Setting actuating direction with 10V DC control signal to “valve open” or closed; 0V DC
“valve closed” as well as the position feedback. = valve closed
Actuator Switch Function
Equal % control / Linear control
Switch 4 Setting of actuating control curve to either equal percentage or linear Linear control The valve functions are adjusted with the DIP
control.
Failsafe open/close
switches under the connection cover.
Switch 5 Close
Setting actuator direction at power failure to “valve open” or “valve closed”.
Electrical override
Setting override function to ON and the actuator will open valve fully.
Switch 6 Off
When set to OFF again, the actuator will re-calibrate and thereafter go into
normal operation mode.

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 7

MLE75MAB ACTUATORS
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLE series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Floating / Modulating Actuating Force: 600N -50N/+100N Humidity rating: 0-85% RH, no
(universal) Stroke: 7 mm / 0.276 in condensation
Supply Voltage: 24V AC/DC ±10%, Operation Time: 22 sec/mm (failsafe Position Indicator: Yes
50/60 Hz mode: 5 sec/mm) Wire Connection: Fixed,
Failsafe Function: Yes, optional open or Power Consumption: 5 wires x 0.50 mm2, 1.5 meter cable
close 24V AC: 7.9VA operating (9VA max.) CE Conformity: EN 60730
Control Signal: Analog 0(2)-10V DC or 24V DC: 3.7W operating (4.5W max.) Protection Rating: IP54 incl. upside-
digital 2-position with constant power Ambient Temperature: 0°C to +50°C down, class III, indoor use only
supply (+32°F to +122°F) Weight: 0.34 kg / 0.75 lb
Feedback: Yes, control signal (analog) or Media temperature: 0°C to +120°C Valve Size Compatibility: DN40 – DN50
0-10V DC (digital) (+32°F to +248°F) Override: Electrical

MEASUREMENTS & DIMENSIONS WIRING CONNECTIONS

MLE75MAB Actuator
0(2)-10V modulating

Yellow
Brown

Green
Grey
Blue
Input signal Feedback signal
0(2)-10V DC 0(2)-10V DC
<0.5mA
Power 24V AC/DC

Ground/common
Signal ground

MLE75MAB Actuator
2-Position, Normally Closed

Yellow
Brown

Green
Grey
Blue

Feedback signal
Close Open 0-10V DC

Power 24V AC/DC

L W H WEIGHT
ACTUATOR T Ground/common
MM (IN) MM (IN) MM (IN) KG (LB) Signal ground

MLE75MAB 96.0 (3.78) 56 (2.20) 91 (3.58) M30x1.5 0.34 (0.75)

MLE75MAB Actuator
3-Point Floating, Normally Closed

ACTUATOR SWITCH FUNCTIONS

Yellow
Brown

Green
Grey
Blue

SWITCH FACTORY Stop Feedback signal

SWITCH FUNCTION Close Open 0(2)-10V DC
NUMBER SETTINGS
Auto cycle ON/OFF Power 24V AC/DC
If the plant specifications permit it, the auto cycle can be activated during
commissioning. Auto cycle prevents the valve from jamming when the Ground/common
Switch 1 valve is not moved for a longer period of inactivity, e.g. for heating systems OFF Signal ground
during the summer. When the auto cycle is activated, the actuator will
perform 50% stroke cycle if no stroke movement has occurred during a
3-weeks period.
Analog 2-10V DC / 0-10V DC
Switch 2 Setting control range by the continuous actuating signal 0-10V DC or 0-10V DC
2-10V DC.
Normally open / Normally closed Normally
Switch 3 Setting actuating direction with 10V DC control signal to “valve open” or closed; 0V DC
“valve closed” as well as the position feedback. = valve closed
Equal % control / Linear control
Switch 4 Setting of actuating control curve to either equal percentage or linear Linear control
control.
Failsafe open/close
Switch 5 Close
Setting actuator direction at power failure to “valve open” or “valve closed”.
Electrical override
Setting override function to ON and the actuator will open valve fully.
Switch 6 Off
When set to OFF again, the actuator will re-calibrate and thereafter go into
normal operation mode.
Actuator Switch Function
The valve functions are adjusted with the DIP
switches under the connection cover.

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 8

MLP41MNA-NU ACTUATORS
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: On/Off or Floating Position Indicator: Yes Protection Rating: IP54, class II
Supply Voltage: 110/230V AC ±10%, Operation Time: 27.2 sec/mm CE Conformity: EN 60730
50/60 Hz Actuating Force: 200N Wire Connection:
Type: Bi-directional step motor Stroke: 1 to 8.5 mm / 0.04 to 0.33 in (auto Fixed, 3 wires x 0.80 mm², 1.5 meter cable
Power Consumption: 8VA adjusting) Closing point adjustment: During
Control Signal: Digital (2-position / Ambient Temperature: 0°C to +50°C operation the actuator will self-adjust
3-point floating) (+32°F to +122°F) according to the closing point and stroke
Feedback: No Media temperature: 0°C to +120°C length of the valve.
Failsafe Function: No (+32°F to +248°F) Weight: 0.23 kg / 0.51 lb
Manual Override: Yes (5 mm Allen key) Humidity Rating: 0 to 85% RH, no Valve Size Compatibility: DN15 - DN32
condensation

MEASUREMENTS & DIMENSIONS

L W H WEIGHT
ACTUATOR T
MM (IN) MM (IN) MM (IN) KG (LB)
MLP41MNA-NU 93.0 (3.66) 50.0 (1.97) 88 (3.46) M30x1.5 0.23 (0.51)

WIRING CONNECTIONS
MLP41MNA-NU Actuator
2-Position
White

Red
Black

Open Close

Power 110/230V AC

Ground/common

MLP41MNA-NU Actuator
3-Point Floating
White

Black

Red

Stop
Open Close

Power 110/230V AC

Ground/common
VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 9
MLP71MNA-NU ACTUATORS
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series actuators, which have been designed
for use with the threaded VPI PICV series. They enable a new dimension of benefits
to HVAC control, offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Modulating Manual Override: Yes, 4 mm (~5/72”) Protection Rating: IP54, class III,
Supply Voltage: 24V AC/DC ±15%, Allen Key including upside-down, indoor use only
50/60 Hz Position Indicator: Yes CE Conformity: EN 60730
Type: Electrical bi-directional step motor Operation Time: 5.5 sec/mm Wire Connection:
Power Consumption: Actuating Force: 200N (-30N/+70N) Fixed, 3 wires x 0.22 mm², 1.5 meter cable
24V AC: 6VA Stroke: 1 to 8.5 mm / 0.04 to 0.33 in (auto Fixed, 3 wires x AWG24, 4.9 ft
24V DC: 4W adjusting) Closing point adjustment: During
Inrush Current: 1.8A (peak) Ambient Temperature: 0°C to +50°C operation the actuator will self-adjust
Control Signal: Analog 0-10V DC (+32°F to +122°F) according to the closing point and stroke
Media temperature: 0°C to +120°C length of the valve.
Resolution: 1:100
(+32°F to +248°F) Weight: 0.23 kg / 0.51 lb
Feedback: No
Humidity Rating: 0 to 85% RH, no Valve Size Compatibility: DN15 - DN32
Control Mode: Linear
condensation
Failsafe Function: No

MEASUREMENTS & DIMENSIONS WIRING CONNECTIONS

L W H WEIGHT
ACTUATOR T
MM (IN) MM (IN) MM (IN) KG (LB)
MLP71MNA-NU 93.0 (3.66) 50 (1.97) 88 (3.46) M30x1.5 0.23 (0.51)

WIRING CONNECTIONS

MLP71MNA-NU Actuator
0-10V modulating
White

Black

Red

Input signal
0-10V
Power 24V AC/DC

Ground/common
MLP41TNA ACTUATORS
(THERMOELECTRIC ACTUATORS)
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series thermoelectric actuators,

which have been designed for use with the threaded VPI PICV
series. They enable a new dimension of benefits to HVAC control,
offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: On/Off Stroke: 6.5 mm /0.256 in Wire Connection: Fixed,
Supply Voltage: 230V AC ±10%, Operation Time: approx 4.5 minutes4 2 wires x 0.75 mm2, 1 meter cable
50/60 Hz Power Consumption: 1.2W Protection Rating: IP54 including upside-
Failsafe Function: Yes, normally closed3 Ambient Temperature: 0°C to +60°C down, class II
Control Signal: ON/OFF, normally closed (+32°F to +140°F) Weight: 0.11 kg / 0.24 lb
Actuating Force: 140 N Valve Size Compatibility: DN15-DN32

Note 3: To ensure that the valve is in an open position during the commissioning of the system, the actuator will be delivered in open position and
remain in this position until it is electrically operated first time.

Note 4: Closing time is approximately double dependent on ambient temperature.

MEASUREMENTS & DIMENSIONS

L Ø W H H WEIGHT
ACTUATOR
MM (IN) MM (IN) MM (IN) MINIMUM MAXIMUM KG (LB)

MLP41TNA 48.4 (1.91) 38.0 (1.50) 44.1 (1.74) 61.0 (2.40) 69.3 (2.73) 0.11 (0.24)

WIRING CONNECTIONS

MLP41TNA Actuator
2-Position, Normally Closed
Brown
Blue

Close Open

Power 230V AC

Ground/common

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 11

MLP71TNA ACTUATORS
(THERMOELECTRIC ACTUATORS)
It is critical to select and use the best possible actuators to achieve optimum
indoor climate control with PICVs. Faster and more accurate actuators
respond better to the control signal, for better results and higher comfort.

Honeywell offers the impressive MLP series thermoelectric actuators,

which have been designed for use with the threaded VPI PICV
series. They enable a new dimension of benefits to HVAC control,
offering designers, system integrators, and building owners.

TECHNICAL SPECIFICATIONS
Operation: Modulating Stroke: 6.5 mm /0.256 in Protection Rating: IP54 including upside-
Supply Voltage: 24 V AC -10%...+20%, Operation Time: approx 4.5 minutes6 down, class III
50/60 Hz Power Consumption: 1.2 W Weight: 0.12 kg / 0.27 lb
Failsafe Function: Yes, normally closed5 Ambient Temperature: 0 °C to + 60 °C / Valve Size Compatibility: DN15-DN32
Control Signal: Analog 0-10 V, normally +32 °F to +140 °F
closed Wire Connection: Plug-in,
Actuating Force: 125 N ± 5% 3 wires x 0.22 mm2, 1 meter cable
Note 5: To ensure that the valve is in an open position during the commissioning of the system, the actuator will be delivered in open position and
remain in this position until it is electrically operated first time.

Note 6: Closing time is approximately double dependent on ambient temperature.

MEASUREMENTS & DIMENSIONS

L Ø W H H WEIGHT
ACTUATOR
MM (IN) MM (IN) MM (IN) MINIMUM MAXIMUM KG (LB)

MLP71TNA 63.5 (2.5) 38.0 (1.50) 44.1 (1.74) 63.5 (2.5) 71.8 (2.83) 0.12 (0.27)

WIRING CONNECTIONS

MLP71TNA Actuator
0-10V DC modulating
Black

Red
Blue

0-10V DC

Power 24V AC

Ground/common

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 12

FLOW-RATE SETTINGS

DIFFERENTIAL
VALVE CLOSE-OFF
MAXIMUM FLOW RATE PRESSURE PN
MODEL NO. DIAMETER PRESSURE END CONNECTION
RANGE RATING
MM L/H M3/H GPM KPA KPAD
VPI015TWL2 DN15 1110 1.11 4.89 800 30 - 800 PN25 Fixed female threaded ISO

VPI015TPL2 DN15 1110 1.11 4.89 800 30 - 800 PN25 Fixed female threaded ISO

VPI015TWH2 DN15 2650 2.7 11.7 800 35 - 800 PN25 Fixed female threaded ISO

VPI015TPH2 DN15 2650 2.7 11.7 800 35 - 800 PN25 Fixed female threaded ISO

VPI020TWL2 DN20 1110 1.11 4.89 800 30 - 800 PN25 Fixed female threaded ISO

VPI020TPL2 DN20 1110 1.11 4.89 800 30 - 800 PN25 Fixed female threaded ISO

VPI020TWH2 DN20 2650 2.7 11.7 800 35 - 800 PN25 Fixed female threaded ISO

VPI020TPH2 DN20 2650 2.7 11.7 800 35 - 800 PN25 Fixed female threaded ISO

VPI025TWH2 DN25 2650 2.7 11.7 800 35 - 800 PN25 Fixed female threaded ISO

VPI025TPH2 DN25 2650 2.7 11.7 800 35 - 800 PN25 Fixed female threaded ISO

VPI032TWH2 DN32 4630 4.6 20.4 800 16 - 800 PN25 Fixed female threaded ISO

VPI032TPH2 DN32 4630 4.6 20.4 800 16 - 800 PN25 Fixed female threaded ISO

VPI040TPH2 DN40 13647 13.6 60.1 800 16 - 600 PN25 Fixed female threaded ISO

VPI050TPL2 DN50 13647 13.6 60.1 800 16 - 600 PN25 Fixed female threaded ISO

FLOW SETTING DIAL

Honeywell’s VPI series Pressure Independent Control Valves offers selection of wide range of flow settings.
These valves are specially equipped with Scale setting dials on top of the valve body. To adjust the preferred
flow settings, adjust the below shown dials (as per valve model) with a unique adjustment key.

DN15/20 (LF) AND DN32 DN15/20/25 (HF) DN 40/50 (THREADED)

For example - A micrometer For example - A micrometer setting For example - A micrometer setting
setting of 3.2 (DN32 valve) on dial, of 2.3 on dial, corresponds to a of 3.7 on dial, corresponds to a
corresponds to a maximum flow rate maximum flow rate of: 1430 l/h maximum flow rate of: 11142 l/h
of: 3350 l/h (17.7 GPM) (6.28 GPM) (49 GPM)

FLOW SETTINGS
WORKING DIFFERENTIAL
MODEL NUMBER MAXIMUM FLOW RATE
PRESSURE
DN15/DN20 (LF) 64 l/h – 1110 l/h 30 kPaD – 800 kPaD

DN15/DN20/DN25 (HF) 620 l/h – 2650 l/h 35 kPaD – 800 kPaD

DN32 865 l/h – 4630 l/h 16 kPaD – 800 kPaD

DN40/DN50 1900 l/h – 13647 l/h 16 kPaD – 600 kPaD

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 13

MAXIMUM FLOW-RATE LIMITATION SETTINGS

DN15LF-DN20LF DN15HF-DN20HF DN32 DN40-DN50

SETTING
L/SEC L/HR GPM L/SEC L/HR GPM L/SEC L/HR GPM L/SEC L/HR GPM
0.0178 64 0.282 - - - 0.240 865 3.81 0.528 1900 8.36 1.0

0.0393 142 0.624 - - - 0.282 1010 4.46 0.633 2278 10.0 1.1

0.0580 209 0.920 - - - 0.322 1160 5.10 0.738 2655 11.7 1.2

0.0743 268 1.180 - - - 0.361 1300 5.72 0.843 3033 13.3 1.3

0.0887 319 1.41 - - - 0.399 1430 6.32 0.947 3410 15.0 1.4

0.102 366 1.61 0.172 620 2.73 0.435 1570 6.90 1.05 3787 16.7 1.5

0.113 408 1.80 0.200 720 3.17 0.471 1700 7.47 1.16 4163 18.3 1.6

0.124 446 1.96 0.228 820 3.61 0.506 1820 8.02 1.26 4537 20.0 1.7

0.134 482 2.12 0.258 930 4.10 0.540 1940 8.56 1.36 4909 21.6 1.8

0.143 516 2.27 0.294 1060 4.67 0.573 2060 9.08 1.47 5279 23.2 1.9

0.152 549 2.42 0.325 1170 5.15 0.605 2180 9.59 1.57 5646 24.8 2.0

0.161 580 2.56 0.350 1260 5.55 0.636 2290 10.1 1.67 6011 26.4 2.1

0.170 611 2.69 0.375 1350 5.95 0.667 2400 10.6 1.77 6372 28.0 2.2

0.178 641 2.82 0.396 1430 6.28 0.696 2510 11.0 1.87 6730 29.6 2.3

0.186 671 2.95 0.417 1500 6.61 0.725 2610 11.5 1.97 7083 31.2 2.4

0.194 700 3.08 0.439 1580 6.96 0.753 2710 11.9 2.06 7432 32.7 2.5

0.202 728 3.21 0.458 1650 7.27 0.780 2810 12.4 2.16 7776 34.2 2.6

0.210 756 3.33 0.481 1730 7.62 0.807 2900 12.8 2.25 8115 35.7 2.7

0.218 783 3.45 0.500 1800 7.93 0.832 3000 13.2 2.35 8449 37.2 2.8

0.225 810 3.56 0.522 1880 8.28 0.858 3090 13.6 2.44 8777 38.6 2.9

0.232 835 3.68 0.542 1950 8.59 0.882 3180 14.0 2.53 9098 40.0 3.0

0.239 860 3.79 0.550 1980 8.72 0.906 3260 14.4 2.61 9413 41.4 3.1

0.245 883 3.89 0.558 2010 8.85 0.930 3350 14.7 2.70 9721 42.8 3.2

0.252 906 3.99 0.567 2040 8.99 0.953 3430 15.1 2.78 10021 44.1 3.3

0.257 927 4.08 0.575 2070 9.12 0.975 3510 15.5 2.86 10314 45.4 3.4

0.263 946 4.17 0.583 2100 9.25 0.997 3590 15.8 2.94 10599 46.6 3.5

0.268 965 4.25 0.597 2150 9.47 1.02 3670 16.1 3.02 10875 47.8 3.6

0.273 982 4.32 0.611 2200 9.69 1.04 3740 16.5 3.10 11142 49.0 3.7

0.277 998 4.39 0.625 2250 9.91 1.06 3820 16.8 3.17 11400 50.2 3.8

0.281 1010 4.46 0.639 2300 10.1 1.08 3890 17.1 3.24 11649 51.3 3.9

0.285 1020 4.51 0.653 2350 10.4 1.10 3960 17.4 3.30 11888 52.3 4.0

0.288 1040 4.57 0.661 2380 10.5 1.12 4030 17.7 3.37 12116 53.3 4.1

0.291 1050 4.61 0.669 2410 10.6 1.14 4100 18.1 3.43 12334 54.3 4.2

0.294 1060 4.66 0.678 2440 10.7 1.16 4170 18.4 3.48 12540 55.2 4.3

0.296 1070 4.70 0.686 2470 10.9 1.18 4240 18.7 3.54 12735 56.0 4.4

0.299 1080 4.73 0.694 2500 11.0 1.20 4300 19.0 3.59 12919 56.8 4.5

0.301 1080 4.77 0.703 2530 11.1 1.21 4370 19.2 3.64 13090 57.6 4.6

0.303 1090 4.80 0.711 2560 11.3 1.23 4440 19.5 3.68 13249 58.3 4.7

0.305 1100 4.83 0.719 2590 11.4 1.25 4500 19.8 3.72 13395 58.9 4.8

0.307 1100 4.86 0.728 2620 11.5 1.27 4570 20.1 3.76 13527 59.5 4.9

0.308 1110 4.89 0.736 2650 11.7 1.29 4630 20.4 3.79 13647 60.0 5.0

Accuracy: Greatest of either ±10% of controlled flow rate or ±5% of maximum flow rate.

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 14

MODEL SELECTION (PART NOMENCLATURE)
VPI SERIES VALVE BODIES
PRESSURE MAXIMUM PRESSURE
VALVE TYPE VALVE SIZE CONNECTION TYPE
TEST PORTS FLOW RATE CLASS
VPI - Valve Pressure P - With Pressure
015 - DN15 / 0.5 inch T - Threaded DN Size L - Low Max Flow 2 - PN25
Independent Ports

W - Without
020 - DN20 / 0.75 inch H - High Max Flow
Pressure Ports

025 - DN25 / 1 inch

032 - DN32 / 1.25 inch

040 - DN40 / 1.5 inch

050 - DN50 / 2 inch

VPI 015 T P H 2

Example: VPI015TPH2

• Without Pressure Test Port models are available only for DN15-DN32

• Low Flow (LF) models are available only for DN15 and DN20.

VPI SERIES ACTUATORS

CONTROL AND POWER ACTUATOR
ACTUATOR TYPE FAIL-SAFE FEEDBACK VALVE SIZE
VOLTAGE TECHNOLOGY
T - Thermoelectric A - Analog A - DN15-DN32
ML - Motor Linear P - Power Failure 'In place' 41 - On/Off 230Vac Actuator feedback (Threaded)

B - DN40-DN50
E - Electronic Fail-Safe 71 - Modulating (0)2-10Vdc M - Electric Actuator N - No feedback (Threaded)

75 - Floating / Modulating
(universal)

ML P 71 M N A

Example: MLP71MNA
Note: For MLP41MNA-NU actuators, use the same model selection with extra -NU at the end for non UL listed actuators.

ACCESSORIES
List of Available Accessories

PART CODE PART NAME

VPI-PP-TP VPI Series Pressure Ports - Test Plugs

VPI-FSK VPI Series Flow Setting Key

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 15

VALVE AND ACTUATOR COMPATIBILITY
DN15 – DN32 VALVE AND ACTUATOR COMPATIBILITY
ACTUATOR PART NUMBER
PARAMETERS
MLP41 MLP71
MLP71MAA MLE71MAA MLP71MNA MLP41TNA MLP71TNA
MNA-NU MNA-NU

24 Vac/dc 24 Vac/dc 24 Vac/dc 110/230 Vac 24 Vac/dc 110/230V 24 Vac/dc

Voltage +/-10%, +/-10%, +/-15%, +/-10%, +/-10%, AC ±10%, +/-10%,
Power Supply 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz 50/60Hz

Power (Peak) 4.7VA 6.8VA 4.7VA 1.2W 1.2W 8VA 6VA / 4W

0-10 Vdc • • • • •

2-10 Vdc • • •
Control
2-Position SPDT • •
On-Off / 2-Position SPST •
Feedback (0)2-10Vdc • •

Actuator Force/Torque (N/Nm) 240 N 250 N 160 N 140 N 125 N 200 N 200 N

Running Time (sec/mm) 22 sec/mm 22 sec/mm 22 sec/mm 270 sec 210 sec 27.2 5.5 sec/mm

Electronic Fail-
Power Fail Safe Action Fail In Place Fail In Place Fail Safe Fail Safe Fail Safe Fail Safe
Safe

Cable length
Electrical Connection 1.5 m 1.5 m 1.5 m 1m 1m 1.5 m 1.5 m
(meter)

QMAX Valve Model

Valve Size Compatibility
(l/h) Number
DN15 LF 1110 VPI015TWL2 • • • • • • •

DN15P LF 1110 VPI015TPL2 • • • • • • •

DN15 HF 2,650 VPI015TWH2 • • • • • • •

DN15P HF 2,650 VPI015TPH2 • • • • • • •

DN20 LF 1110 VPI020TWL2 • • • • • • •

DN20P LF 1110 VPI020TPL2 • • • • • • •

DN20 HF 2,650 VPI020TWH2 • • • • • • •

DN20P HF 2,650 VPI020TPH2 • • • • • • •

DN25 2,650 VPI025TWH2 • • • • • • •

DN25P 2,650 VPI025TPH2 • • • • • • •

DN32 4,630 VPI032TWH2 • • • • • • •

DN32P 4,630 VPI032TPH2 • • • • • • •

Note 7: DN32 valves when used with MLP41TNA or MLP71TNA might exceed specified leakage rate.

Note 8: Thermal Actuators closing time is approximately double dependent on ambient temperature.

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 16

VALVE AND ACTUATOR COMPATIBILITY
DN40 – DN50 VALVE AND ACTUATOR COMPATIBILITY
ACTUATOR PART NUMBER
PARAMETERS
MLP75MAB MLE75MAB
Voltage 24 Vac/dc, +/-10%, 50/60Hz 24 Vac/dc, +/-10%, 50/60Hz
Power Supply
Power (Peak) 9VA 9VA

0-10 Vdc • •

Control 2-10 Vdc • •

2-Position SPDT • •

Feedback (0)2-10 Vdc • •

Actuator Force/Torque (N/Nm) 600 N 600 N

Running Time (sec/mm) 22 sec/mm 22 sec/mm

Power Fail Safe Action Fail In Place Electronic Fail-Safe

Electrical Connection Cable length (meter) 1.5m 1.5m

Valve Size QMAX (l/h) Valve Model Number Compatibility

DN40 13,647 VPI040TPH2 • •

DN50 13,647 VPI050TPL2 • •

APPLICATION AND SCHEMATIC EXAMPLE

VPI series Pressure Independent Control Valves and Actuators | www.honeywell.com | 17

For more and ordering Information

UNITED ARAB EMIRATES ASEAN LATAM

Honeywell Building Technologies Honeywell Building Honeywell Building Technologies
Building Management Systems Technologies (ASEAN) Building Management Systems
Emaar Business Park, Sheikh Zayed Road, Honeywell International Sdn Bhd Av. Santa Fe No. 94, Torre A – Piso 1
Building No. 2, 2nd floor, 201 Level 25, UOA Corp Tower, Lobby B Col. Colonia Zedec Santa Fe , México , CDMX.
Post Office Box 232362, Avenue 10, The Vertical, Bangsar South City C.P. 01210.
Dubai, United Arab Emirates. 59200, Kuala Lumpur, Malaysia. Call: +52 (55) 5241-4800
Call: +971 44541704 Call: +60 3-2777 3100 Email: [email protected]
Email: [email protected]

TURKEY
Honeywell Teknoloji A.Ş. PACIFIC
Cayir Cad. No:7 Kat:1 Honeywell Building Technologies
Icerenkoy 34752 Istanbul, Turkey. 2 Richardson Pl, North Ryde NSW 2113,
Call: +90 216 578 71 10 Australia.
Faks: +90 216 575 66 37 Call: 1300 363 936
Email: [email protected]

QATAR
Honeywell Technology Solutions KOREA
P.O. Box 63757, Doha, Qatar Honeywell HBT Buildings
Phone: +974 4 4066 200 Technologies
Fax: +974 4 4066 711 5F SangAm IT Tower, 434 Worldcup buk-ro,
Mapo-gu, Seoul 03922, Korea.
Call: 0082-2-799-6271, 6009,
INDIA
6158, 3535, 6361
Honeywell HBT India Buildings
Email: [email protected]
Unitech Trade Center, 5th Floor, Sector-43,
Block C, Sushant Lok Phase - I,
Gurgaon - 122 002, India.
Call: 1-800-103-0339 31-00381-01 | Rev 03 | 09/22
Email: [email protected] © 2022 Honeywell International Inc.