Scribd
Upload
50 views2 pages

DTS - Mid Term Question Bank

The document contains 8 questions related to design of transmission systems. The questions cover topics like beam strength calculation of spur gear tooth, law of gearing, design of spur gear pair, force analysis on worm and worm gear tooth, thermal consideration in worm gear, components of tooth forces and efficiency of worm gear drive.

Uploaded by

omchavan9296
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
50 views2 pages

DTS - Mid Term Question Bank

The document contains 8 questions related to design of transmission systems. The questions cover topics like beam strength calculation of spur gear tooth, law of gearing, design of spur gear pair, force analysis on worm and worm gear tooth, thermal consideration in worm gear, components of tooth forces and efficiency of worm gear drive.

Uploaded by

omchavan9296
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

JSPM’s Jayawantrao Sawant College of Engineering

Department of Mechanical Engineering


TE Mechanical 2019 Pattern
Subject: Design of Transmission Systems (Subject Code: 302051)

MTT Question Bank 2023-2024


___________________________________________________________________________________

Q. No. Question Statement CO BL PI Marks

Write the assumptions consider for beam strength of spur


1,10,
Q. 1 gear. Derive an expression for beam strength of spur gear 1 2 6
tooth. 12

Q. 2 State law of gearing and derive expression for it. 1 2 1,10,12 6

It is required to design a pair of spur gear 20° full depth


involute teeth. Take Zp =20 and Zg=60. The input shaft rotate
at 1000 rpm and receives 20 kW. Both gears are made by steel
material with σb =260MPa. Take Cs =1.25, Ca =1. Take
3
CV =
3+V
2.86 1,2,10,1
Q. 3 𝑌 = 0.484 − 1 3 9
𝑧 2
21 v (𝑐𝑏 + 𝑐𝑎 𝑐𝑠 𝑃𝑡 )
𝑃𝑑 =
21 v + √(𝑐𝑏 + 𝑐𝑎 𝑐𝑠 𝑝𝑡 )
i) Find module for spur gear and Specify Dimensions at
v=5m/sec, FOS = 2
ii) Find effective load and correct factor of safety at e-40
microns and C =11400 N/mm²
iii) Find BHN at FOS 1.5

A spur gear pair with 20° full-depth involute tooth profile


consist of 18 teeth pinion meshing with 36 teeth gear. The
pinion is connected to an electric motor running at 1440 r.p.m.
The pinion & gear are made of steel with ultimate tensile
strengths of 600 N/mm2 and 510 N/mm2 respectively. The
module is 5 mm while the face width is 10 times the module.
The surface hardness of pinion and gear are 330 BHN and 280
BHN respectively. If the required factor of safely is 2, 1,2,10,1
Q. 4 1 3 9
calculate: 2
(i) the beam strength;
(ii) the wear strength;
(iii) the maximum static load the gear pair can transmit; and
(iv) the rated power the gear pair can transmit.
5.6
Assume velocity factor, dynamic load. Cv = 5.6+√V accounts
for the dynamic load.
1,10,
Q. 5 Explain force analysis on worm and worm gear tooth. 2 2 6
12

1,10,
Q. 6 Write short note on thermal consideration in worm gear. 2 2 6
12

A pair of worm gear is designated as 1/52/10/8 transmit 5 kW


power at 900 rpm is supplied to worm shaft. If the coefficient
of friction is 0.04 and pressure angle is 20°, determine
i) Components of tooth forces acting on the worm and worm
1,2,10,1
Q. 7 wheel; 2 3 9
2
ii) The efficiency of the worm gear drive; and
iii) The temperature rise the lubricating oil, if effective
surface area is 3.0 m2 with heat transfer coefficient of 15
W/m2 °C.

A worm gear pair 1/40/10/4 consists of worm gear made of


phosphor bronze (sand cast) and worm made of case-hardened
steel 10C4. The coefficient of friction is 0.035 while the 1,2,10,1
Q. 8 2 3 9
normal pressure angle is 20°. If the worm rotates at 1000 r.p.m. 2
determine the input power rating based on i) Beam strength ii)
Wear strength

********************

You might also like