Tyrin 200

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

SAFETY DATA SHEET

THE DOW CHEMICAL COMPANY

Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin
Print Date: 01/06/2016

THE DOW CHEMICAL COMPANY encourages and expects you to read and understand the entire
(M)SDS, as there is important information throughout the document. We expect you to follow the
precautions identified in this document unless your use conditions would necessitate other appropriate
methods or actions.

1. IDENTIFICATION
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Resin

Recommended use of the chemical and restrictions on use


Identified uses: A polyethylene plastic - For industrial conversion as a raw material for manufacture
of articles or goods. We recommend that you use this product in a manner consistent with the listed
use. If your intended use is not consistent with the stated use, please contact your sales or technical
service representative. A polyethylene plastic - For industrial conversion as a raw material for
manufacture of articles or goods. We recommend that you use this product in a manner consistent
with the listed use. If your intended use is not consistent with the stated use, please contact your sales
or technical service representative.

COMPANY IDENTIFICATION
THE DOW CHEMICAL COMPANY
2030 WILLARD H DOW CENTER
MIDLAND MI 48674-0000
UNITED STATES

Customer Information Number: 800-258-2436


SDSQuestion@dow.com

EMERGENCY TELEPHONE NUMBER


24-Hour Emergency Contact: 800-424-9300
Local Emergency Contact: 800-424-9300

2. HAZARDS IDENTIFICATION
Hazard classification
This material is hazardous under the criteria of the Federal OSHA Hazard Communication Standard
29CFR 1910.1200.
Combustible dust

Label elements

Signal word: WARNING!

® ™ Trademark of The Dow Chemical Company ("Dow") or an affiliated Page 1 of 10


company of Dow
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

Hazards
May form combustible dust concentrations in air

Precautionary statements
Prevention
Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
Ground/bond container and receiving equipment.
Use explosion-proof electrical/ ventilating/ lighting/ equipment.
Take precautionary measures against static discharge.

Other hazards
no data available

3. COMPOSITION/INFORMATION ON INGREDIENTS

This product is a mixture.


Component CASRN Concentration

Ethene, homopolymer, chlorinated 64754-90-1 >= 94.0 %

Calcium carbonate 471-34-1 <= 6.0 %

4. FIRST AID MEASURES


Description of first aid measures
General advice: First Aid responders should pay attention to self-protection and use the
recommended protective clothing (chemical resistant gloves, splash protection). If potential for
exposure exists refer to Section 8 for specific personal protective equipment.

Inhalation: Move person to fresh air; if effects occur, consult a physician.

Skin contact: Wash off with plenty of water. Seek first aid or medical attention as needed. If molten
material comes in contact with the skin, do not apply ice but cool under ice water or running stream of
water. DO NOT attempt to remove the material from skin. Removal could result in severe tissue
damage. Seek medical attention immediately. Suitable emergency safety shower facility should be
immediately available.

Eye contact: Flush eyes thoroughly with water for several minutes. Remove contact lenses after the
initial 1-2 minutes and continue flushing for several additional minutes. If effects occur, consult a
physician, preferably an ophthalmologist.

Ingestion: If swallowed, seek medical attention. May cause gastrointestinal blockage. Do not give
laxatives. Do not induce vomiting unless directed to do so by medical personnel.

Most important symptoms and effects, both acute and delayed: Aside from the information found
under Description of first aid measures (above) and Indication of immediate medical attention and

Page 2 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

special treatment needed (below), any additional important symptoms and effects are described in
Section 11: Toxicology Information.

Indication of any immediate medical attention and special treatment needed


Notes to physician: If burn is present, treat as any thermal burn, after decontamination. If hydrogen
chloride is liberated due to thermal degradation, treat as hydrogen chloride exposure. If lavage is
performed, suggest endotracheal and/or esophageal control. Danger from lung aspiration must be
weighed against toxicity when considering emptying the stomach. No specific antidote. Treatment of
exposure should be directed at the control of symptoms and the clinical condition of the patient.

5. FIREFIGHTING MEASURES
Suitable extinguishing media: Water fog or fine spray. Dry chemical fire extinguishers. Carbon
dioxide fire extinguishers. Foam.

Unsuitable extinguishing media: no data available

Special hazards arising from the substance or mixture


Hazardous combustion products: During a fire, smoke may contain the original material in addition
to combustion products of varying composition which may be toxic and/or irritating. Combustion
products may include and are not limited to: Carbon monoxide. Carbon dioxide. Hydrogen chloride.

Unusual Fire and Explosion Hazards: Do not permit dust to accumulate. When suspended in air
dust can pose an explosion hazard. Minimize ignition sources. If dust layers are exposed to elevated
temperatures, spontaneous combustion may occur. Dense smoke is emitted when burned without
sufficient oxygen.

Advice for firefighters


Fire Fighting Procedures: Keep people away. Isolate fire and deny unnecessary entry. Soak
thoroughly with water to cool and prevent re-ignition. If material is molten, do not apply direct
waterstream. Use fine water spray or foam. Cool surroundings with water to localize fire zone. Hand
held dry chemical or carbon dioxide extinguishers may be used for small fires. Dust explosion hazard
may result from forceful application of fire extinguishing agents.

Special protective equipment for firefighters: Wear positive-pressure self-contained breathing


apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet, coat, trousers,
boots, and gloves). If protective equipment is not available or not used, fight fire from a protected
location or safe distance.

6. ACCIDENTAL RELEASE MEASURES


Personal precautions, protective equipment and emergency procedures: Spilled material may
cause a slipping hazard. Use appropriate safety equipment. For additional information, refer to
Section 8, Exposure Controls and Personal Protection.

Environmental precautions: Prevent from entering into soil, ditches, sewers, waterways and/or
groundwater. See Section 12, Ecological Information.

Page 3 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

Methods and materials for containment and cleaning up: Contain spilled material if possible.
Sweep up. Collect in suitable and properly labeled containers. See Section 13, Disposal
Considerations, for additional information.

7. HANDLING AND STORAGE


Precautions for safe handling: Use with adequate ventilation. No smoking, open flames or sources
of ignition in handling and storage area. Good housekeeping and controlling of dusts are necessary
for safe handling of product. Avoid breathing process fumes. When appropriate, unique handling
information for containers can be found on the product label. Workers should be protected from the
possibility of contact with molten resin. Do not get molten material in eyes, on skin or clothing.
Pneumatic conveying and other mechanical handling operations can generate combustible dust. To
reduce the potential for dust explosions, electrically bond and ground equipment and do not permit
dust to accumulate. Dust can be ignited by static discharge. See Section 8, EXPOSURE CONTROLS
AND PERSONAL PROTECTION.

Conditions for safe storage: Store in accordance with good manufacturing practices.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION


Control parameters
Exposure limits are listed below, if they exist.
Component Regulation Type of listing Value/Notation
Hydrochloric acid ACGIH C 2 ppm
OSHA Z-1 C 7 mg/m3 5 ppm

A reaction or decomposition product may be formed during handling or processing which has an
Occupational Exposure Limit (OEL)., Hydrogen chloride may be generated under thermal degradation
conditions.

Exposure controls
Engineering controls: Use local exhaust ventilation, or other engineering controls to maintain
airborne levels below exposure limit requirements or guidelines. If there are no applicable exposure
limit requirements or guidelines, general ventilation should be sufficient for most operations. Local
exhaust ventilation may be necessary for some operations.

Individual protection measures


Eye/face protection: Use safety glasses (with side shields). If there is a potential for
exposure to particles which could cause eye discomfort, wear chemical goggles. If exposure
causes eye discomfort, use a full-face respirator.
Skin protection
Hand protection: Chemical protective gloves should not be needed when handling
this material. Consistent with general hygienic practice for any material, skin contact
should be minimized. Use gloves to protect from mechanical injury. Selection of
gloves will depend on the task. Use gloves with insulation for thermal protection,
when needed.
Other protection: No precautions other than clean body-covering clothing should be
needed.
Respiratory protection: Respiratory protection should be worn when there is a potential to
exceed the exposure limit requirements or guidelines. If there are no applicable exposure limit
requirements or guidelines, wear respiratory protection when adverse effects, such as

Page 4 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

respiratory irritation or discomfort have been experienced, or where indicated by your risk
assessment process. Use an approved air-purifying respirator when vapors are generated at
increased temperatures or when dust or mist is present.
The following should be effective types of air-purifying respirators: When dust/mist are
present use a/an Particulate filter. When combinations of vapors, acids, or dusts/mists are
present use a/an Organic vapor with acid gas cartridge and particulate pre-filter.

9. PHYSICAL AND CHEMICAL PROPERTIES


Appearance
Physical state Powder
Color Off-white
Odor Odorless
Odor Threshold Odorless
pH Not applicable
Melting point/range No test data available
Freezing point Not applicable
Boiling point (760 mmHg) Not applicable
Flash point closed cup Not applicable
Evaporation Rate (Butyl Acetate Not applicable
= 1)
Flammability (solid, gas) May form combustible dust concentrations in air
Lower explosion limit Not applicable
Upper explosion limit Not applicable
Vapor Pressure Not applicable
Relative Vapor Density (air = 1) Not applicable
Relative Density (water = 1) 1.2 - 1.8 Estimated.
Water solubility Negligible
Partition coefficient: n- no data available
octanol/water
Auto-ignition temperature No test data available
Decomposition temperature No test data available
Kinematic Viscosity Not applicable
Explosive properties No test data available
Oxidizing properties No test data available
Molecular weight no data available

NOTE: The physical data presented above are typical values and should not be construed as a
specification.

Page 5 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

10. STABILITY AND REACTIVITY


Reactivity: no data available

Chemical stability: Stable.

Possibility of hazardous reactions: Polymerization will not occur.

Conditions to avoid: Exposure to elevated temperatures can cause product to decompose.

Incompatible materials: None known.

Hazardous decomposition products: Decomposition products depend upon temperature, air supply
and the presence of other materials. Processing may release fumes and other decomposition
products. At temperatures exceeding melt temperatures, polymer fragments can be released. Fumes
can be irritating. Decomposition products can include and are not limited to: Aldehydes. Alcohols.
Organic acids. Hydrogen chloride. Decomposition products can include trace amounts of:
Hydrocarbons.

11. TOXICOLOGICAL INFORMATION

Toxicological information on this product or its components appear in this section when such data is
available.

Acute toxicity
Acute oral toxicity
Very low toxicity if swallowed. Harmful effects not anticipated from swallowing small amounts.
May cause choking if swallowed.

Single dose oral LD50 has not been determined.

Typical for this family of materials.


LD50, Rat, > 5,000 mg/kg Estimated.

Acute dermal toxicity


No adverse effects anticipated by skin absorption.

The dermal LD50 has not been determined.

Typical for this family of materials.


LD50, Rabbit, > 2,000 mg/kg Estimated.

Acute inhalation toxicity


Dust may cause irritation to upper respiratory tract (nose and throat). Thermal degradation of
the resin may generate hydrogen chloride gas at concentrations which may cause respiratory
irritation.

The LC50 has not been determined.,

Page 6 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

Skin corrosion/irritation
Prolonged contact is essentially nonirritating to skin.
Mechanical injury only.
Under normal processing conditions, material is heated to elevated temperatures; contact with the
material may cause thermal burns.

Serious eye damage/eye irritation


Solid or dust may cause irritation or corneal injury due to mechanical action.
Thermal degradation of the resin may generate hydrogen chloride gas at concentrations which may
cause eye irritation.

Sensitization
No relevant data found.

For respiratory sensitization:


No relevant data found.

Specific Target Organ Systemic Toxicity (Single Exposure)


Evaluation of available data suggests that this material is not an STOT-SE toxicant.

Specific Target Organ Systemic Toxicity (Repeated Exposure)


Based on available data, repeated exposures are not anticipated to cause significant adverse effects.

Carcinogenicity
No relevant data found.

Teratogenicity
For the minor component(s): Did not cause birth defects or any other fetal effects in laboratory
animals.

Reproductive toxicity
For the minor component(s): In animal studies, did not interfere with fertility. In animal studies, did not
interfere with reproduction.

Mutagenicity
For the minor component(s): In vitro genetic toxicity studies were negative.

Aspiration Hazard
Based on physical properties, not likely to be an aspiration hazard.

12. ECOLOGICAL INFORMATION

Ecotoxicological information on this product or its components appear in this section when such data
is available.

Toxicity
Acute toxicity to fish
Not expected to be acutely toxic to aquatic organisms.

Page 7 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

Persistence and degradability


Biodegradability: This water-insoluble polymeric solid is expected to be inert in the
environment. Surface photodegradation is expected with exposure to sunlight. No
appreciable biodegradation is expected.

Bioaccumulative potential
Bioaccumulation: No bioconcentration is expected because of the relatively high molecular
weight (MW greater than 1000).

Mobility in soil
In the terrestrial environment, material is expected to remain in the soil where it may be
subject to wind dispersion.
In the aquatic environment, material will sink and remain in the sediment.

13. DISPOSAL CONSIDERATIONS


Disposal methods: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND, OR INTO ANY BODY
OF WATER. All disposal practices must be in compliance with all Federal, State/Provincial and local
laws and regulations. Regulations may vary in different locations. Waste characterizations and
compliance with applicable laws are the responsibility solely of the waste generator. AS YOUR
SUPPLIER, WE HAVE NO CONTROL OVER THE MANAGEMENT PRACTICES OR
MANUFACTURING PROCESSES OF PARTIES HANDLING OR USING THIS MATERIAL. THE
INFORMATION PRESENTED HERE PERTAINS ONLY TO THE PRODUCT AS SHIPPED IN ITS
INTENDED CONDITION AS DESCRIBED IN MSDS SECTION: Composition Information. FOR
UNUSED & UNCONTAMINATED PRODUCT, the preferred options include sending to a licensed,
permitted: Recycler. Reclaimer. Incinerator or other thermal destruction device. Landfill. If
incineration is used, take precautions to guard against the formation of explosive dust air mixtures
when handling combustible powders.

14. TRANSPORT INFORMATION


DOT
Not regulated for transport

Classification for SEA transport (IMO-IMDG):


Not regulated for transport
Transport in bulk Consult IMO regulations before transporting ocean bulk
according to Annex I or II
of MARPOL 73/78 and the
IBC or IGC Code

Classification for AIR transport (IATA/ICAO):


Not regulated for transport

This information is not intended to convey all specific regulatory or operational


requirements/information relating to this product. Transportation classifications may vary by container

Page 8 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

volume and may be influenced by regional or country variations in regulations. Additional


transportation system information can be obtained through an authorized sales or customer service
representative. It is the responsibility of the transporting organization to follow all applicable laws,
regulations and rules relating to the transportation of the material.

15. REGULATORY INFORMATION


OSHA Hazard Communication Standard
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard,
29 CFR 1910.1200.

Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and
Community Right-to-Know Act of 1986) Sections 311 and 312
Acute Health Hazard

Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and
Community Right-to-Know Act of 1986) Section 313
This material does not contain any chemical components with known CAS numbers that exceed the
threshold (De Minimis) reporting levels established by SARA Title III, Section 313.

Pennsylvania Worker and Community Right-To-Know Act:


The following product components are cited in the Pennsylvania Hazardous Substance List and/or the
Pennsylvania Environmental Substance List, and are present at levels which require reporting.

Components CASRN
Calcium carbonate 471-34-1

California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986)
This product contains no listed substances knownto the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.

United States TSCA Inventory (TSCA)


All components of this product are in compliance with the inventory listing requirements of the U.S.
Toxic Substances Control Act (TSCA) Chemical Substance Inventory.

16. OTHER INFORMATION

Revision
Identification Number: 101209110 / A001 / Issue Date: 03/02/2015 / Version: 2.0
Most recent revision(s) are noted by the bold, double bars in left-hand margin throughout this
document.

Page 9 of 10
Product name: TYRIN™ 200 Powdered Chlorinated Polyethylene Issue Date: 03/02/2015
Resin

Legend
ACGIH USA. ACGIH Threshold Limit Values (TLV)
C Ceiling limit
OSHA Z-1 USA. Occupational Exposure Limits (OSHA) - Table Z-1 Limits for Air
Contaminants

Information Source and References


This SDS is prepared by Product Regulatory Services and Hazard Communications Groups from
information supplied by internal references within our company.

THE DOW CHEMICAL COMPANY urges each customer or recipient of this (M)SDS to study it
carefully and consult appropriate expertise, as necessary or appropriate, to become aware of and
understand the data contained in this (M)SDS and any hazards associated with the product. The
information herein is provided in good faith and believed to be accurate as of the effective date shown
above. However, no warranty, express or implied, is given. Regulatory requirements are subject to
change and may differ between various locations. It is the buyer's/user's responsibility to ensure that
his activities comply with all federal, state, provincial or local laws. The information presented here
pertains only to the product as shipped. Since conditions for use of the product are not under the
control of the manufacturer, it is the buyer's/user's duty to determine the conditions necessary for the
safe use of this product. Due to the proliferation of sources for information such as manufacturer-
specific (M)SDSs, we are not and cannot be responsible for (M)SDSs obtained from any source other
than ourselves. If you have obtained an (M)SDS from another source or if you are not sure that the
(M)SDS you have is current, please contact us for the most current version.

Page 10 of 10

You might also like