Scribd
Upload
16 views

Arduino

This document describes how to build an altitude meter using an Arduino, BMP180 pressure sensor, and OLED display. It lists the components needed, details how to connect the circuit, and explains how the BMP180 sensor measures pressure and altitude. The code reads the altitude from the sensor and displays it on the OLED in meters.

Uploaded by

Shariff Oluoch Odiwuor
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
16 views

Arduino

This document describes how to build an altitude meter using an Arduino, BMP180 pressure sensor, and OLED display. It lists the components needed, details how to connect the circuit, and explains how the BMP180 sensor measures pressure and altitude. The code reads the altitude from the sensor and displays it on the OLED in meters.

Uploaded by

Shariff Oluoch Odiwuor
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Arduino-based altitude meter using

BMP180 sensor
BMP180 is a digital pressure sensor designed for low-power, low-voltage operation in
mobile phones, navigation devices, and personal digital assistants. The sensor has an I2C
interface to communicate sensor data. It can operate on 2.5~3.6V and consumes only 12
uA even in the ultra-high-resolution mode. The sensor can be used for several
applications, including measuring altitude from sea level, measurement of altitude from
ground, measuring vertical velocity, and detecting weather conditions.

In this project, we have developed an altitude meter using the BMP180 sensor and our
favorite microcontroller board – Arduino. This altitude meter displays real-time altitude
from sea level on a small OLED display. The OLED display used to current altitude is
SSD1306.

Components required

1. Arduino UNO/any Arduino board x1


2. BMP180 pressure sensor x1
3. SSD1306 OLED x1
4. Connecting wires/jumper wires

Circuit connections
The altitude meter is designed by interfacing the SSD1306 OLED and BMP180 pressure
sensor with the Arduino UNO. BMP180 sensor has four terminals – Vin, Gnd, SCL, and
SDA. The Vin and Gnd pins of the sensor are connected to 3.3V out and a ground pin of
Arduino UNO. The SCL and SDA pins of the sensor can be connected to any of the I2C
ports on the Arduino board. The I2C ports on Arduino UNO are shown in the image
below.

The SSD1306 OLED is connected to Arduino using a physical SPI port. For interfacing
SSD1306 OLED via physical SPI port, connect the D0/SCK and D1/MOSI pins of SSD1306
OLED to pins D13 and D11 of Arduino, respectively. Connect pins DC, RESET, and CS of
SSD1306 to pins D9, D10, and D8 of Arduino, respectively. The final circuit looks as
follows.

How the circuit works


BMP180 is a piezoresistive sensor that is used to detect atmospheric pressure. The
sensor measures both temperature and pressure as both of these factors affect air
density. The temperature is measured to compensate for pressure readings according to
the changes in air density. The sensor outputs the atmospheric pressure in Pascals over
its I2C interface.

There are Arduino libraries available for BMP180 sensors from Adafruit and Sparkfun. In
this project, we are using the library from Sparkfun, and this library converts the sensor
output in Pascals to hectoPascals.
The sensor first reads uncompensated temperature reading, then uncompensated
pressure reading. Finally, it does some complex calculations with both these readings
involving a number of coefficients stored in its EEPROM to give accurate barometric
pressure and temperature. The barometric pressure varies with the altitude, and the
atmospheric pressure decreases with the increase in altitude and vice-versa. A change of
1 Hectopascal corresponds to around 8 meters in altitude. The BMP180 is a very
sensitive sensor and responds to even minute changes in true atmospheric pressure. The
following equation gives the altitude for sea level.

altitude = 44330 * (1 – (Pcurrent/Psealevel)^(1/5.255))

The sensor itself takes care to perform all these complex calculations and
straightforwardly outputs the current true barometric pressure.

Arduino listens to the barometric pressure from the BMP180 sensor over its I2C
interface. The Sparkfun library provides reading temperature, pressure, and altitude
functions, and Arduino reads the altitude reading and displays the reading over
SSD1306 OLED.

The OLED display is connected to the physical SPI port of the Arduino. So, the OLED
communicates with the controller over the SPI interface while the BMP180 sensor relays
the pressure readings over the I2C interface. Arduino reads altitude from BMP180 via I2c
and displays it on the OLED display via SPI. The displayed output reading is in meters.

The code
First of all, the SPI and Wire libraries are imported for data communication over SPI and
I2C interfaces. The Adafruit_GFX and Adafruit_SSD1306 libraries are imported to work
with the SSD1306 OLED display. The Sparkfun BMP180 library is imported to work with
the BMP180 sensor. Constants and pin assignments for the OLED display are defined. An
object ‘display’ of class ‘Adafruit_SSD1306’ is instantiated to deal with the OLED display,
and an object ‘pressure’ of class ‘ SFE_BMP180’ is instantiated to deal with the BMP180
sensor. A variable ‘baseline’ is defined to store the reference atmospheric pressure at
sea level. Next, a bitmap array is defined to store EEWORLDONLINE logo.

In the setup() function, the baud rate for data communication is set to 9600 bps. The
display is initialized using display.begin() method. If the pressure detects the BMP180
sensor.begin() method, the logo is flashed to the OLED display. Otherwise, the “Device
not working” message flashes to the OLED.
In the loop() function, variables to store pressure and altitude readings are declared. The
pressure is read by calling the user-defined function getPressure(). The baseline
atmospheric pressure for the current location is defined. This is set to 1013 as the
altitude is read with respect to sea level here. The altitude is measured by calling the
altitude() method overpressure object with the given baseline. The OLED display is
cleared using display.clearDisplay() method. The cursor is set to start the screen using
display. setCursor() method. The text size is set to 2 using display. setTextSize() method.
The text color is set to white using setTextColor() method. The read altitude is printed to
OLED using display.print() and display.println() methods. The readings flash on OLED
when the display.display(0 method is called. A delay of 1500 ms is provided by calling
delay() function before the next iteration of the loop() function.

The getPressure() function reads the barometric pressure from BMP180 sensor. It uses
the Sparkfun library’s startTemperature(), getTemperature() and startPressure()
methods.

You might also like