Scribd
Upload
37 views2 pages

QP Format COPO

This document contains a question paper for a theory and design of structures course. The question paper contains 4 questions with multiple parts each. Question 1 is compulsory and contains short questions testing various concepts. Questions 2-4 contain numerical problems related to structural analysis testing concepts like bending stresses, shear stresses, slope and deflection calculations.

Uploaded by

Tejesh Nanaware
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
37 views2 pages

QP Format COPO

This document contains a question paper for a theory and design of structures course. The question paper contains 4 questions with multiple parts each. Question 1 is compulsory and contains short questions testing various concepts. Questions 2-4 contain numerical problems related to structural analysis testing concepts like bending stresses, shear stresses, slope and deflection calculations.

Uploaded by

Tejesh Nanaware
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Semester: BACHLOR OF ARCHITECTURE Course Code

III SUBJECT : THEORY & DESIGN OF


STRUCTURES III
DATE:21.12.2022 AY:2022-2023 Max. Marks : 50 BARC304

Instructions:
1. Q.No.1 is compulsory
2. Solve any two questions out of remaining three.
3. Use of non-programmable calculator is allowed.
Q.1 Attempt any FIVE Marks CO BT
a. Write a note on grades of concrete and grades of steel. 5 5,6 1
b. Explain pure bending theory with neat sketch. 5 1 2
c. Define section modulus and find section modulus for 5 1,5,6 3
rectangular section.
d. Explain middle third rule. 5 4 3
e. What do you understand by boundary conditions of a beam? 5 3 2
State boundary conditions for different nature of beam
conditions.
f. Find maximum slope and deflection for a simply supported 5 3 4
beam of span 3m carrying UDL of 6 KN/m over entire span.
g. Write a note on materials used in concrete. 5 5,6 1

Q.2
a. A T-section is used as a simply supported beam for a span of 10 2 1,2,3,4
6m, the beam carries UDL of 10 KN/m over entire span.
Calculate maximum bending stresses induced. Take Top
flange = 150 x 20 mm, web = 20 x 80 mm, I = 1.9 x 108
mm4.
b. Find maximum shear stresses for the beam given in Q.No.2 5 2 1,3
(A)

Q.3
a. A simply supported beam of span 5m carries point load of 60 10 3 1,2,3,4
KN at mid span. Find maximum slope and deflection in the
beam using Macaulay’s method. Take E = 2 x 105 N/mm2
and I = 2 x 108 mm4
b. Define slope and deflection with neat sketch. 5 3 1,2
Q.4
a. A rectangular column 300 mm wide and 200 mm thick 10 4 1,2,3,4
carries a load of 160 KN at an eccentricity of 75 mm in the
plane bisecting the thickness. Find maximum and minimum
stresses.
b. Define direct and eccentric load. State the effect of eccentric 5 4 1,2
load with respect to stresses developed.

Please use this Question Paper Format for preparing the question paper.
NOTE:

1. Please refer the syllabus for COs.


2. Please refer Bloom’s Taxonomy (BTs).
[BT1 – Remembering, BT2 – Understanding, BT3 – Applying, BT4 - Analysing,
BT5 – Evaluating, BT6 – Creating]
3. Please enter CO & BT No. in the question paper.
4. All questions are to be unique in the same question paper and also if more than
one question paper is requested
5. Marks are to be allotted as per the number of hours allotted for each CO/ module.
6. A brief answer key (points) with proper mark split up is to be uploaded.
7. Use font: Times new roman & Font size: 12.

The Question Paper submitted in other formats will not be


considered For further processing

You might also like