Scribd
Upload
30 views2 pages

Assignment Questions

Uploaded by

Mayandi Kalimuthu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
30 views2 pages

Assignment Questions

Uploaded by

Mayandi Kalimuthu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Unit-1 Assignment Questions

1) The following differential equation is available for a physical phenomenon. 𝑨𝑬 =


𝒅 𝒖/𝒅𝒙 +𝒂𝒙 = 𝟎, The boundary conditions are u(0) = 0, 𝑨𝑬 = (𝒅𝒖/𝒅𝒙) 𝒙=𝑳 = 𝟎 By
𝟐 𝟐

using Galerkin’s technique, find the solution of the above differential equation.

2) Find the deflection at the centre of a simply supported beam of span length “l”
subjected to uniformly distributed load throughout its length as shown in figure
using (a) point collocation method, (b) sub-domain method, (c) Least squares
method, and (d) Galerkin’s method.

3) Consider the differential equation 𝒅𝟐𝒚 𝒅𝒙𝟐 + 𝟒𝟎𝟎𝒙𝟐 = 𝟎 for 𝟎 ≤ 𝒙 ≤ 𝟏 subject to


boundary conditions Y(0) = 0, Y(1) = 0. The functions corresponding to this
l

problem, to be eternized is given by 𝑰 = ∫ {−0 .5 [𝒅𝒚/ 𝒅𝒙] + 𝟒𝟎𝟎𝒙 𝒀}. Find the
𝟐

0
solution of the problem using Ray Light Ritz method by considering a two term
solution as ( 𝒙) = 𝒄𝟏𝒙 (𝟏 - 𝒙 )+ 𝒄𝟐𝒙 (𝟏 - 𝒙).
𝟐

4) Consider a 1mm diameter, 50m long aluminum pin-fin as shown in figure used to
enhance the heat transfer from a surface wall maintained at 300C. Calculate the
temperature distribution in a pin-fin by using Rayleigh – Ritz method. Take, 𝒌 =
𝟐𝟎𝟎𝒘/𝒎𝐂 for aluminum h= 𝟐𝟎𝟎𝒘/𝒎𝟐𝐂, 𝑻∞ = 𝟑𝟎𝐂.

5) A simply supported beam subjected to uniformly distributed load over entire span
and it is subject to a point load at the centre of the span. Calculate the bending
moment and deflection at mid span by using Rayleish – Ritz method.
Unit-2 Assignment

1. Determine the axial vibration of a steel bar shown in fig. Take


[E]=2.1×105𝑵/𝒎𝒎𝟐, [ρ] = 7800 𝑲𝒈/𝒎𝟑

2. Consider the simply supported beam shown in fig. let the length L=1m,
E=2×1011𝑵/𝒎𝟐, area of cross section A=30Cm2, moment of inertia I=100mm4,
density [ρ] = 7800𝑲𝒈/𝒎𝟑. Determine the natural frequency using two types of
mass matrix. Lumped mass matrix and consistent mass matrix.

3. For a tapered plate of uniform thickness t = 10mm as shown in fig. find the
displacements at the nodes by forming in to two element model. The bar has
mass density ρ = 7800𝑲𝒈/𝒎𝟑 Young’s modulus E = 2×105𝑴𝑵/𝒎𝟐. In addition
to self weight the plate is subjected to a point load p = 10KN at its centre. Also
determine the reaction force at the support.

You might also like