MM 2864760 0102

MM
Maintenance Manual
HI 020V
2636960-0200
TechPub_2614345_0106 - MM_2864760_0102fro.fm
WARNING
Read and follow all safety precautions before working on or near
this equipment.
Read all safety precautions throughout this manual and on safety
signs attached to this equipment. Failure to follow all safety
precautions could result in death or serious injury.
Doc. No. MM-2864760-0102

TechPub_2614345_0106 - MM_2864760_0102fro.fm
Copyright © 2008 Tetra Pak Group
All rights reserved. No part of this document may be reproduced or copied in any form or by any means
without written permission from Tetra Pak Packaging Solutions
and all Tetra Pak products are trademarks belonging to the Tetra Pak Group.
The content of this manual is in accordance with the design and construction of the machine or
equipment at the time of publishing. Tetra Pak reserves the right to introduce design modifications
without prior notice.
This document was produced by:
Tetra Pak Packaging Solutions
Via Delfini 1
41100 Modena
Italy
Additional copies can be ordered from Tetra Pak Parts or the nearest Tetra Pak office. When ordering
additional copies, always provide the document number. This can be found in the machine specification
document. It is also printed on the front cover and in the footer on each page of the manual.
Doc. No. MM-2864760-0102
Issue 2008-09
This manual is valid for: i Introduction
Series No./ Machine No. Sign.

ii Safety Precautions
1 Headspace by gas
Injection
MM
Maintenance Manual
iii Index of Procedures
HI 020V
2636960-0200
TechPub_2614345_0106 - MM_2864760_0102fro.fm
A list of all optional equipment, optional

kits, and rebuilding kits that this manual is
valid for is found on the next page.
Doc. No. MM-2864760-0102
Issue 2008-09

Valid for:
Tetra Pak A3/Flex

648575-0100
Tetra Pak A3/Flex

648575-0150
TechPub_2614345_0106 - MM_2864760_0102fro.fm
Update Log for Doc. No. MM-2864760-0102
This table shows all changes made to this manual, such as kits installed
and pages added or removed.
Date Installed Kit Added Pages Removed Pages Signature

(Doc. No.)
TechPub_2614345_0106 - MM_2864760_0102fro.fm
Date Installed Kit Added Pages Removed Pages Signature
(Doc. No.)
TechPub_2614345_0106 - MM_2864760_0102fro.fm
i Introduction
TechPub_2614345_0104 - MM_2864760_0102int.fm
Doc. No. MM-2864760-0102 i - 1 (16)

i Introduction
This chapter contains basic information about this manual

and related Tetra Pak equipment.
TechPub_2614345_0104 - MM_2864760_0102int.fm
i - 2 (16) Doc. No. MM-2864760-0102

i Introduction Table of Contents
Manual Information . . . . . . . . . . . . . . . . . . . . . . . . i - 5
Delivered Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . i - 5
Page Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 6
Page Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 7
Typographical Conventions . . . . . . . . . . . . . . . . . . i - 7
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 7
Machine Introduction . . . . . . . . . . . . . . . . . . . . . . i - 8
Intended Use of the Equipment . . . . . . . . . . . . . . . i - 8
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 8
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 8
Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 9
TechPub_2614345_0104 - MM_2864760_0102int.fm
CE Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 9
Machine Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 9
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 10
Hygiene. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i - 11
Microbiological Pollution . . . . . . . . . . . . . . . . . . . i - 11
Steam Barrier in the Product Valve . . . . . . . . . . . i - 11
Abbreviations and Terminology . . . . . . . . . . . . . i - 12
How to Use This Maintenance Manual . . . . . . . i - 13

MM Procedure Codes . . . . . . . . . . . . . . . . . . . . . . i - 13
Procedure Start Table . . . . . . . . . . . . . . . . . . . . . . i - 14
Tetra Pak Maintenance System. . . . . . . . . . . . . . . i - 15
Planned Maintenance Program . . . . . . . . . . . . . . .i - 15
Checklists and Spare Parts Recommendations . .i - 15
Doc. No. MM-2864760-0102 i - 3 (16)

i Introduction
TechPub_2614345_0104 - MM_2864760_0102int.fm
This page intentionally left blank
i - 4 (16) Doc. No. MM-2864760-0102

i Introduction Manual Information
Manual Information
Tetra Pak recommends reading all delivered manuals carefully. Make sure
that the delivered manuals are available to personnel who operate or
maintain the equipment.
It is important to keep this manual for the lifetime of the equipment and to
pass the manual on to any subsequent holder or user.
Tetra Pak will not be held responsible for any damage to the equipment
caused by not following the instructions given in this manual.
Delivered Manuals
The manuals delivered with this equipment include:
• Conversion Manual (CM)
This manual provides technicians with information on converting the
equipment between different production modes
• Electrical Manual (EM)
This manual provides technicians with information about the
equipment’s electrical system
• Installation Manual (IM)
This manual provides technicians with information required to safely
TechPub_2614345_0104 - MM_2864760_0102int.fm
install the equipment

• Maintenance Manual (MM)
This manual provides technicians with information on maintaining the
equipment
• Operation Manual (OM)
This manual provides the operator with information on handling and
operating the equipment before, during, and after production
• Spare Parts Catalogue (SPC)
This manual provides the information necessary to order spare parts
from Tetra Pak
• Technical Manual (TeM)
– provides technicians with information required to safely install the
equipment
– provides technicians with information on maintaining the equipment
– provides technicians with information about the equipment’s
electrical system
– provides the information necessary to order spare parts from
Tetra Pak.
Doc. No. MM-2864760-0102 i - 5 (16)

Manual Information i Introduction
Page Layout
Every main page in a manual contains a header and a footer. The page header
contains the section name (1) and the chapter name (2). The page footer
contains the manual’s document number (3), and the page number (4). See
also the section Page Numbering.
1 2
3.4 Motor 3 Drive
(Cont'd)
a) Remove the banjo connections (2).
b) Loosen the cable to the micro switch.
c) Remove the cross bar (3) and separate the disconnection link. Lower the
link arm.
d) Remove the screws (4), apply the extractor, and pull out the shaft.
e) Remove the screws (5) and the washer.
f) Change the bearing.
g) Repeat steps g) and h) for the upper bearing.
4
2
TechPub_2614345_0104 - MM_2864760_0102int.fm
4
2 Banjo connection
3 cross bar
4 Screw
5 Screw
(Cont'd)
Doc. No. MM-123457-0108 3 - 15 (102)
3 4
1 Section name
2 Chapter name
3 Document number
4 Page number
i - 6 (16) Doc. No. MM-2864760-0102

i Introduction Manual Information
Page Numbering
A page number has three parts:
• chapter number (1)
• consecutive page number (2) within the chapter
• total number of pages (3) in the chapter.
4 - 11 (18) 1 Chapter number

2 Consecutive page number
1 2 3 3 Total number of pages
Typographical Conventions
Controls on the operator panel, emergency stop devices, and program steps
are printed in CAPITAL LETTERS.
Cross-references are underlined.
Symbols
TechPub_2614345_0104 - MM_2864760_0102int.fm
The following symbols are used in illustrations:

• A pointer arrow (1) indicates the position of an object
• A zoom arrow (2) indicates that an object view is enlarged. The arrow
points towards the enlarged view of the object
• A rotation movement arrow (3) indicates rotational movement of an
object. The arrow points in the direction of rotation
• A straight movement arrow (4) indicates movement of an object.
The arrow points in the direction of movement
• The hygiene symbol (5) indicates that the current procedure requires the
operator to disinfect their hands or gloves and to follow hygiene rules.
1 2 3
1 Pointer arrow
2 Zoom arrow
3 Rotation movement arrow
4 Straight movement arrow
4 5 5 Hygiene symbol
Doc. No. MM-2864760-0102 i - 7 (16)

Machine Introduction i Introduction
Machine Introduction
Intended Use of the Equipment
The intended use of this Tetra Pak equipment is to pack liquid food products.
All other use is prohibited. Tetra Pak will not be held responsible for injury
or damage if the equipment is used for any other purpose.
Manufacturer
This Tetra Pak equipment has been manufactured by:
Via Delfini 1
41100 Modena
Italy
Service
If you encounter problems when operating this equipment, contact the
nearest Tetra Pak office.
Contact the Tetra Pak A3 Liaison with other inquiries, comments, or
suggestions for improvement regarding the equipment and its
TechPub_2614345_0104 - MM_2864760_0102int.fm
documentation.
i - 8 (16) Doc. No. MM-2864760-0102

i Introduction Identification
Identification
CE Classification
This equipment complies with the basic health and safety regulations of
the European Economic Area (EEA).
Machine Plate
The illustration below shows an example of the machine plate and its
location on the equipment. The machine plate carries data needed when
contacting Tetra Pak concerning this specific equipment.
Make sure that the equipment data in the front pages of this manual
corresponds to the machine plate data and the machine specification.
TechPub_2614345_0104 - MM_2864760_0102int.fm
1 2
Tetra Pak 3
Machine Type
Drawing Spec. 1 Machine type
Machine No.
Manufacturer 4 2 Volume
3 Drawing specifications
Year of Manufacture 5 4 Machine serial number
5 Manufactured by
6 7 6 Year of manufacture
7 CE mark
Doc. No. MM-2864760-0102 i - 9 (16)

Orientation i Introduction
Orientation
The illustration below shows the orientation of the equipment. This
orientation information will be used throughout this manual.
A D
B
A Front
B Right-hand side
C Left-hand side
TechPub_2614345_0104 - MM_2864760_0102int.fm
D Back
i - 10 (16) Doc. No. MM-2864760-0102

i Introduction Hygiene
Hygiene
Microbiological Pollution
To avoid microbiological pollution of the packaging material:
• Always keep the doors to the filling room (area) closed. To prevent
contamination via air streams, never open a window when the equipment
is in production
• Never clean the floors or the equipment in the filling room (area) when
the equipment is in production
• Compressed air used for cleaning purposes is to be used only for
cleaning filters and should only be used outside of the filling room (area)
or in the final folder compartment of the filling machine
• Prepare the splicing of the packaging material as late as possible
• Disinfect your hands before touching anything that may come into
contact with the product. Use disinfectant code H. See the Technical
Data chapter
• Keep your hands and gloves clean
• Always wear some type of hair protection (cap or hairnet) and clean
clothes (preferably white)
TechPub_2614345_0104 - MM_2864760_0102int.fm
• Do not wear a watch, ring, necklace, earrings, or any other exposed

jewellery.
Steam Barrier in the Product Valve

The filling machine’s product valve employs a steam barrier to separate the
product supply line from the filling machine. The steam barrier allows:
• To independently bring the machine and product supply line to the
condition of commercial sterility required to commence the product
filling and packaging operation
• To safeguard the condition of commercial sterility of the product supply
line in all cases in which a filling machine terminates the production
(either temporarily or for the rest of the product supply cycle) while the
product supply line is required to continue feeding other filling machines
in operation.
The steam barrier must never be disengaged and the steam supply must
never be interrupted when the filling machine or the product supply line (or
both) are being brought to (pre-sterilization phase) or are already in
(production phase) the condition of commercial sterility.
Any maintenance activity requiring the disengagement of the steam barrier
of the product valve or the interruption of the steam supply to the machine is
only to be carried out when the product supply line is idle and empty from
product.
Doc. No. MM-2864760-0102 i - 11 (16)

Abbreviations and Terminology i Introduction
Abbreviations and Terminology

Abbreviation/ Meaning Translation
Terminology
AN Analog
ANSI American National Standards Institute
ASU Automatic Splicing Unit
B Base (package shape)
CIP Cleaning In Place
DE Distribution Equipment
DI Digital
DIMC Direct Injection Moulded Concept
ECM Engineering Change Management
EM Electrical Manual
HI Headspace by gas Injection
ISO International Organization for Standardization
ICU Integrated Cleaning Unit
IH Induction Heating
LED Light Emitting Diode
TechPub_2614345_0104 - MM_2864760_0102int.fm
LH Left Hand
LS Longitudinal Seal(ing)
MB Master Batch
min Minimum
max Maximum
MKC Mandatory Kit Corrective
MKS Mandatory Kit Human and Product Safety
MM Maintenance Manual
OK Optional Kit
OE Optional Equipment
OM Operation Manual
PE Polyethylene
PM Packaging Material
PT PullTab
RH Right Hand
RK Rebuilding Kit
RM Rebuilding Manual
S Slim (package shape)
SA Strip Applicator
SPC Spare Parts Catalogue
Sq Square (package shape)
TBA Tetra Brik Aseptic
TMCC Tetra Pak Multi-purpose Compact Controller
TPOP Tetra Pak Operator Panel
TS Transversal Sealing
UK Upgrade Kit
i - 12 (16) Doc. No. MM-2864760-0102

i Introduction How to Use This Maintenance Manual
How to Use This Maintenance Manual

MM Procedure Codes
Maintenance procedures are designated as shown in the example.
1.2.3-1 Worm Gear - Change Oil

MM Chapter or Subsection Name Subject
main machine group of activity
MM Section or
Types of Procedure
machine group
The following types of procedure are used:
– adjust – fill
MM Subsection or
machine subgroup – assemble – install
– bleed – lubricate
– calibrate – measure
Sequential procedure
number – change – overhaul
– charge – record
– check – remove
TechPub_2614345_0104 - MM_2864760_0102int.fm
– clean – set
– count – synchronise
– delime – tighten
– dismantle – turn
– empty
Doc. No. MM-2864760-0102 i - 13 (16)

How to Use This Maintenance Manual i Introduction
Procedure Start Table

Each maintenance procedure described in this manual begins with a table
containing information needed to begin the procedure. This information
includes the following:
• Machine status (1) shows actuator status, program step, and any other
machine status necessary to begin the procedure
• Special equipment (2) shows a list of personal protective equipment
and special tools that are not normally carried by a service technician,
but are needed in the procedure
• Consumables (3) shows items, such as lubricants, that are required to
perform the procedure. Consumables do not include replacement parts.
• SPC reference (4) shows the assembly number, found in the index of the
Spare Parts Catalogue (SPC)
1.2.3-1 Worm Gear - Change Oil

Machine status Power supply disconnecting device OFF
1 Air valve OFF

Steam valve ON
Special equipment Torque wrench minimum 55 NM
2 Protective gloves TP No. 90303-12
TechPub_2614345_0104 - MM_2864760_0102int.fm
Apron TP No. 90303-13
Consumables 2 litre high pressure oil
3 SPC reference
Grease code N
123456-0100
4
1 Machine status
2 Special equipment
3 Consumables
4 SPC reference
i - 14 (16) Doc. No. MM-2864760-0102

i Introduction How to Use This Maintenance Manual
Tetra Pak Maintenance System

To ensure uninterrupted production, all equipment must be maintained on a
regular basis.
Tetra Pak has developed a planned maintenance system to keep pace with the
ongoing development of new and existing equipment from Tetra Pak, and to
meet the demands set by customers for higher efficiency and better economy.
Planned Maintenance Program
The Tetra Pak planned maintenance system reduces unplanned downtime
and maintenance time for complete production lines, as well as for individual
equipment.
With the Tetra Pak planned maintenance system, preventive maintenance can
be performed before production is affected. The system is continually
updated based on experience with Tetra Pak equipment worldwide.
The Tetra Pak planned maintenance system maintains records of when
maintenance is performed, when parts are changed, whether alterations are
made, and so on. These records, combined with usage statistics, enable
reliable predictions of the service life of all equipment parts.
TechPub_2614345_0104 - MM_2864760_0102int.fm
Checklists and Spare Parts Recommendations

Customers using the Tetra Pak planned maintenance system receive
checklists from their local Tetra Pak office whenever planned maintenance is
due. These checklists are individualised for each customer, according to the
type of equipment, equipment usage, and maintenance occasion. In addition,
the system recommends spare parts, rotation units, tools, and templates
according to the statistics collected.
Tip! Contact the local Tetra Pak office for additional information about
the Tetra Pak Maintenance System and its planned maintenance
program.
Doc. No. MM-2864760-0102 i - 15 (16)

How to Use This Maintenance Manual i Introduction
TechPub_2614345_0104 - MM_2864760_0102int.fm
i - 16 (16) Doc. No. MM-2864760-0102

TechPub_2614345_0105 - MM_2864760_0102sp.fm
Doc. No. MM-2864760-0102 ii - 1 (42)

Safety Precaution Instructions
WARNING
Read all safety precaution instructions throughout this manual and on
safety signs attached to this equipment.
Failure to follow all safety precaution instructions could result in death or
serious injury.
Definition of Lockout Procedure

A lockout procedure is a procedure to put each necessary energy isolating
device in its safe position to prevent the energisation of the equipment, such
as when a maintenance procedure should be carried out.
A lockout is the use of a device, for example, a padlock, to make sure that an
energy isolating device cannot be operated.
An energy isolating device is a mechanical device that physically prevents
transmission or release of energy, such as a power supply disconnector.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 2 (42) Doc. No. MM-2864760-0102

ii Safety Precautions Table of Contents
Safety Messages Description. . . . . . . . . . . . . . . ii - 5
Personnel Requirements . . . . . . . . . . . . . . . . . . ii - 6
Skilled Person . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 6
Instructed Person. . . . . . . . . . . . . . . . . . . . . . . . . . ii - 6
Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 7
Locations of Safety Signs. . . . . . . . . . . . . . . . . . . . ii - 9
HI Equipment (OE) . . . . . . . . . . . . . . . . . . . . . . . . . ii - 21
Protective Devices. . . . . . . . . . . . . . . . . . . . . . . ii - 23
Emergency Stop. . . . . . . . . . . . . . . . . . . . . . . . . . ii - 23
Emergency Stop Push-Buttons . . . . . . . . . . . . . . ii - 24
Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 25
Warning Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 27
TechPub_2614345_0105 - MM_2864760_0102sp.fm
Audible Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 27
Personal Protection. . . . . . . . . . . . . . . . . . . . . . ii - 28
Noise Hazard . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 28
Entanglement Hazard . . . . . . . . . . . . . . . . . . . . . ii - 28
Hazardous Substances . . . . . . . . . . . . . . . . . . . ii - 29
Disposal of Chemical Substances . . . . . . . . . . . ii - 30
Hydrogen Peroxide (H2O2) . . . . . . . . . . . . . . . . . ii - 31
Emergency Procedures. . . . . . . . . . . . . . . . . . . . . ii - 31
Personal Protective Equipment . . . . . . . . . . . . . . ii - 32
Handling of Hydrogen Peroxide . . . . . . . . . . . . . . ii - 33
Storage of Hydrogen Peroxide . . . . . . . . . . . . . . . ii - 34
Disposal of Hydrogen Peroxide . . . . . . . . . . . . . . ii - 35
Supply Systems. . . . . . . . . . . . . . . . . . . . . . . . . ii - 36
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 36
Residual Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 36
Electrical Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . ii - 37
Doc. No. MM-2864760-0102 ii - 3 (42)

Table of Contents ii Safety Precautions
Socket Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 38
Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 39
Steam Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 40
Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii - 41
Equipment for Lifting and Moving Loads . . . . ii - 42
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 4 (42) Doc. No. MM-2864760-0102

ii Safety Precautions Safety Messages Description
Safety Messages Description

A safety message is always accompanied by a safety alert symbol and a
signal word.
The safety alert symbol is used to alert about potential personal injury
hazards. To avoid hazards, obey all safety messages that follow this symbol.
The following safety alert symbols and signal words are used in this manual
to inform the user of hazards.
Danger indicates an imminently hazardous situation

DANGER which, if not avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation

which, if not avoided, could result in death or serious
WARNING
injury.
Caution indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate
CAUTION injury. It may also be used to alert against unsafe
practices.
CAUTION Caution without the safety alert symbol indicates a

TechPub_2614345_0105 - MM_2864760_0102sp.fm
potentially hazardous situation which, if not avoided,

may result in property damage.
Doc. No. MM-2864760-0102 ii - 5 (42)

Personnel Requirements ii Safety Precautions
Personnel Requirements
Note! Personnel includes all persons working on or near this equipment.
Only skilled or instructed persons are allowed to work with this equipment.
Skilled Person
A skilled person must have relevant education and experience to enable him
or her to identify hazards, analyse risks, and avoid hazards which electricity,
machinery, chemicals, other energies, and supply systems on this equipment
can create.
Skilled persons must meet local regulations, such as certifications and
qualifications for working with these energies and systems.
Instructed Person
An instructed person must be adequately advised or supervised by a skilled
person. The skilled person enables the instructed person to identify hazards,
analyse risks, and avoid hazards which electricity, machinery, chemicals,
other energies, and supply systems on this equipment can create.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 6 (42) Doc. No. MM-2864760-0102

ii Safety Precautions Safety Signs
Safety Signs
WARNING
Damaged or missing safety signs increase the risk of death or serious
injury.
Replace all missing or damaged safety signs immediately.
Safety signs are attached to the equipment. The table below lists all the signs
that are used, and illustrations show their locations on the equipment. Each
position number refers to two variants of a safety sign in the table, but only
one is used on the equipment.
• Make sure that each safety sign is legible and in its correct position after
installation and maintenance.
• Replace all missing or damaged safety signs immediately.
Pos. ISO sign ANSI sign

1
WARNING
Moving part
can crush and cut.
Do not operate with
guard removed.
Follow lockout procedure
TechPub_2614345_0105 - MM_2864760_0102sp.fm
before maintenance.
Moving part can crush and cut.

Do not operate with guard removed.
Follow lockout procedure before maintenance.
2
DANGER
Hazardous voltage.
Will shock, burn, or cause death.
before maintenance.
Hazardous voltage.
Will shock, burn, or cause death.
3
WARNING
Chemical burn hazard.
Wear personal protective
equipment.
Chemical burn hazard.

Wear personal protective equipment.
Doc. No. MM-2864760-0102 ii - 7 (42)

Safety Signs ii Safety Precautions
Pos. ISO sign ANSI sign

4 WARNING
Hydrogen Peroxide H2O2 Hydrogen Peroxide H2O2
35% w/w UN No.2014 35% w/w UN No.2014

OM
OM
Chemical hazard.
Corrosive and oxidising chemical.
Could cause death or serious injury.
Read Safety Precautions in Operation Manual
(OM) before handling hydrogen peroxide.
Chemical hazard.
Corrosive and oxidising chemical. Could cause death or serious injury.
Read Safety Precautions in Operation Manual (OM) before handling
hydrogen peroxide.
5
WARNING
Risk of eye injury.
Wear eye protection.
Risk of eye injury.

Wear eye protection.
6
TechPub_2614345_0105 - MM_2864760_0102sp.fm
WARNING
Hot surface.
Do not touch.
before maintenance.
Hot surface.
Do not touch.
7
WARNING
Hazardous voltage.
Can shock, burn, or cause death.
Read Maintenance Manual
before using this socket outlet.
Hazardous voltage.
Can shock, burn, or cause death.
Read Maintenance Manual (MM) before using this socket outlet.
8
WARNING
Hazardous rotating
shafts and belts
Can crush and cut
Keep hands clear while
the machine is operating
Hazardous rotating shafts and belts.

Can crush and cut.
Keep hands clear while the machine is operating.
ii - 8 (42) Doc. No. MM-2864760-0102

Locations of Safety Signs

The illustration shows where the safety signs are located. The position
numbers refer to the table in the Safety Signs section.
6
TechPub_2614345_0105 - MM_2864760_0102sp.fm
8 6
8
(Cont'd)
Doc. No. MM-2864760-0102 ii - 9 (42)

(Cont'd)
Upper drying chamber is shown

6 6
TechPub_2614345_0105 - MM_2864760_0102sp.fm
6
8 6
8
(Cont'd)
ii - 10 (42) Doc. No. MM-2864760-0102

(Cont'd)
6
TechPub_2614345_0105 - MM_2864760_0102sp.fm
6
(Cont'd)
Doc. No. MM-2864760-0102 ii - 11 (42)

(Cont'd)
Valid for TBA and TPA packages
TechPub_2614345_0105 - MM_2864760_0102sp.fm
6
6
6
6
6
6
(Cont'd)
ii - 12 (42) Doc. No. MM-2864760-0102

(Cont'd)
Valid for TGA packages
2 2
6 6
TechPub_2614345_0105 - MM_2864760_0102sp.fm
6
6 6
6
(Cont'd)
Doc. No. MM-2864760-0102 ii - 13 (42)

(Cont'd)
TechPub_2614345_0105 - MM_2864760_0102sp.fm
3
3 3
3 4 3
(Cont'd)
ii - 14 (42) Doc. No. MM-2864760-0102

(Cont'd)
2
TechPub_2614345_0105 - MM_2864760_0102sp.fm
(Cont'd)
Doc. No. MM-2864760-0102 ii - 15 (42)

(Cont'd)
TechPub_2614345_0105 - MM_2864760_0102sp.fm
2
2 2
(Cont'd)
ii - 16 (42) Doc. No. MM-2864760-0102

(Cont'd)
2
2
2 2
TechPub_2614345_0105 - MM_2864760_0102sp.fm
2 2 2 2
(Cont'd)
Doc. No. MM-2864760-0102 ii - 17 (42)

(Cont'd)
Valid for TGA packages only
2 2
TechPub_2614345_0105 - MM_2864760_0102sp.fm
2
(Cont'd)
ii - 18 (42) Doc. No. MM-2864760-0102

(Cont'd)
7
TechPub_2614345_0105 - MM_2864760_0102sp.fm
(Cont'd)
Doc. No. MM-2864760-0102 ii - 19 (42)

(Cont'd)
2 2
TechPub_2614345_0105 - MM_2864760_0102sp.fm
(Cont'd)
ii - 20 (42) Doc. No. MM-2864760-0102

(Cont'd)
HI Equipment (OE)
2 6
TechPub_2614345_0105 - MM_2864760_0102sp.fm
(Cont'd)
Doc. No. MM-2864760-0102 ii - 21 (42)

(Cont'd)
TechPub_2614345_0105 - MM_2864760_0102sp.fm
1
1 1
ii - 22 (42) Doc. No. MM-2864760-0102

ii Safety Precautions Protective Devices
Protective Devices
WARNING
Hazardous zones.
Hazardous zones are safeguarded and provided with protective devices. Do
not inch or run this equipment if any protective device is inoperative.
Change inoperative components of the safety system immediately.
WARNING
Hazardous voltage.
Hazardous voltage remains on this equipment after activating an
EMERGENCY STOP or an interlocking device.
Emergency Stop
Emergency stop devices are used to stop this equipment immediately in an
hazardous situation. Learn the positions of all emergency stop devices and
how to use them.
Instructions for a normal production stop are included in the Stop chapter of
the Operation Manual.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
Doc. No. MM-2864760-0102 ii - 23 (42)

Protective Devices ii Safety Precautions
Emergency Stop Push-Buttons

Push one of the EMERGENCY STOP push-buttons to stop this equipment
immediately.
The location of each EMERGENCY STOP push-button is shown by an
arrow.
(behind door)
TechPub_2614345_0105 - MM_2864760_0102sp.fm
X2 (both sides of door)
ii - 24 (42) Doc. No. MM-2864760-0102

Safeguards
WARNING
Moving machinery.
Never defeat or bypass the interlocking devices.
Movable guards, for example, doors and covers leading to hazardous zones,
are fitted with interlocking devices where required. These devices are usually
electric safety switches that are parts of the safety system and must never be
defeated, bypassed, or otherwise made inoperative.
CAUTION
Burn hazard.
Parts of this equipment may be hot after operation.
After installation and maintenance, and before this equipment is inched or
run, check that all safeguards are in place and that they operate correctly.
CAUTION
Equipment damage.
Never stop this equipment by opening an interlocking guard.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
(Cont'd)
Doc. No. MM-2864760-0102 ii - 25 (42)

Protective Devices ii Safety Precautions
(Cont'd)
The location of each interlocking guard is shown by an arrow.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
A3/Flex TGA A3/Flex TBA and TPA
A3/Flex with upper drying chamber is

shown
ii - 26 (42) Doc. No. MM-2864760-0102

Warning Lamp
A warning lamp is a column of warning lights:
• A red light (1) indicates a hazardous condition. This is a situation that
requires immediate action.
• A yellow light (2) indicates an abnormal or impending critical condition.
This is a condition calling for action by the operator.
• A blue light (3) indicates that operator action is required.
Audible Alarm
The audible alarm produces a warning signal every time this equipment is
about to start. The warning signal sounds for approximately three seconds
prior to starting to alert personnel.
2
TechPub_2614345_0105 - MM_2864760_0102sp.fm
1 Red light
2 Yellow light
3 Blue light
Doc. No. MM-2864760-0102 ii - 27 (42)

Personal Protection ii Safety Precautions
Personal Protection
This section applies to all personnel at all times when this equipment is in
operation. For special personal protection required when handling hazardous
substances, see the Hazardous Substances section.
Noise Hazard
CAUTION
Hazardous noise.
Risk of impaired hearing. Hearing protection is recommended whenever this
equipment is in operation.
Entanglement Hazard
WARNING
Risk of entanglement.
Do not wear jewellery or loose clothing when working on or near this
equipment. Long hair may not be loose.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 28 (42) Doc. No. MM-2864760-0102

ii Safety Precautions Hazardous Substances
Hazardous Substances
WARNING
Contact with chemicals can cause death, serious injury, or illness.
Always read and follow the instructions in the safety data sheet supplied by
the manufacturer or local supplier, when handling chemicals.
Make sure that
• the safety data sheet is available
• the showers work
• an eyewash device, movable or wall-mounted, is available and
operational
• additional washing facilities are nearby
Note! Learn the locations of all washing facilities in order to act immediately
in case of an accident
TechPub_2614345_0105 - MM_2864760_0102sp.fm
Doc. No. MM-2864760-0102 ii - 29 (42)

Hazardous Substances ii Safety Precautions
Disposal of Chemical Substances

Always read and follow the disposal instructions in the safety data sheet
supplied by the manufacturer or local supplier.
It is strongly recommended that used chemical containers are
• disposed of according to the instructions immediately after use
• not used as disposal containers for other chemicals in order to avoid
uncontrolled chemical reactions within the container
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 30 (42) Doc. No. MM-2864760-0102

Hydrogen Peroxide (H2O2)
WARNING
Corrosive chemical.
Wear personal protective equipment.
In both liquid and gas states, hydrogen peroxide may cause irritation or
damage if it comes into contact with skin, mucous membranes, eyes, or
clothes. Call for medical attention immediately if there is an accident.
Liquid hydrogen peroxide in concentrations of less than 1% is generally
considered harmless to humans.
Consult the instructions on the label of the tank or container.
Emergency Procedures
If there is an accident involving hydrogen peroxide, rinse the affected area as
soon as possible with large amounts of water.
If hydrogen peroxide is swallowed
• do not attempt to cause vomiting
• drink large amounts of lukewarm water to dilute the peroxide
TechPub_2614345_0105 - MM_2864760_0102sp.fm
• call for medical attention immediately
If splashes or vapour from hydrogen peroxide come in contact with the eyes
• wash the eyes thoroughly with lukewarm water for 15 minutes (keep
eyelids wide apart)
• call for medical attention immediately
If hydrogen peroxide comes into contact with skin or clothes

• rinse immediately with plenty of water
• call for medical attention immediately if skin burns appear
• thoroughly wash the clothes before wearing them again
If irritation or pain is experienced due to having inhaled hydrogen peroxide

vapour
• leave the affected area and get some fresh air
• call for medical attention if the symptoms get worse
Doc. No. MM-2864760-0102 ii - 31 (42)

Personal Protective Equipment

The personal protective equipment for hydrogen peroxide is
• protective goggles (TP No. 90303-11)
• protective gloves made of neoprene (TP No. 90303-12)
• protective apron (TP No. 90303-13)
• protective shoes made of PVC, PE plastic, or rubber
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 32 (42) Doc. No. MM-2864760-0102

Handling of Hydrogen Peroxide
WARNING
Sudden and violent chemical reaction.
Avoid any contamination of hydrogen peroxide.
Hydrogen peroxide reacts suddenly and violently with many compounds or
if it is contaminated. The reaction is a violent decomposition liberating
oxygen and heat, with a big increase in volume due to the oxygen produced
by the peroxide decomposition.
Never pour surplus hydrogen peroxide back into the original container if it
contains fresh hydrogen peroxide. There is a risk of explosion when
hydrogen peroxide is in a closed container.
Ensure that equipment used for handling and diluting hydrogen peroxide is
clean before it comes in contact with hydrogen peroxide. Pumps or other
equipment used for handling hydrogen peroxide must be used for this
purpose only and must be manufactured from appropriate materials, such as
stainless steel 316 L, glass, polyethylene, or teflon. After use, make sure that
all peroxide residue is rinsed away.
If hydrogen peroxide is spilled, dilute it with large amounts of water. Dispose
TechPub_2614345_0105 - MM_2864760_0102sp.fm
of the diluted hydrogen peroxide according to local regulations.
WARNING
Self-ignition.
Never wipe up hydrogen peroxide with materials such as rags or paper as
these may self-ignite several hours after contact. If there is a fire, spray with
large quantities of water.
Doc. No. MM-2864760-0102 ii - 33 (42)

Storage of Hydrogen Peroxide
DANGER
Containers may explode if not properly ventilated.
Keep the container upright and fitted with its proper ventilation cap. If there
is a fire, cool all containers by spraying them with large quantities of water.
Hydrogen peroxide decomposes much faster with increasing temperature.
There is a risk of explosion at high temperatures, since the ventilation cap
cannot release the gases produced quickly enough.
Hydrogen peroxide must be stored in the original container delivered by
the supplier. Keep the container upright and fitted with its proper ventilation
cap, which allows oxygen to escape. Otherwise, there can be an explosion if
decomposition of the peroxide occurs violently.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
Make sure that the container is always properly closed.
(Cont'd)
ii - 34 (42) Doc. No. MM-2864760-0102

(Cont'd)
Commercial food-grade hydrogen peroxide has been stabilized to inhibit the
catalytic decomposition effects of metals and other impurities, but it can
decompose into oxygen and water if it is exposed to heat or contaminated.
Make sure that the area used for storage of hydrogen peroxide is
• cool, clean, and well ventilated
• shielded from direct sunlight
• kept free from combustible materials
Disposal of Hydrogen Peroxide

Always read and follow the disposal instructions in the safety data sheet
supplied by the manufacturer or local supplier.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
Doc. No. MM-2864760-0102 ii - 35 (42)

Supply Systems ii Safety Precautions
Supply Systems
Power Supply
DANGER
Hazardous voltage and moving machinery.
The power supply disconnector must be turned off and secured with a lock
before any maintenance.
Note! The key to the lock must be removed by the technician and retained in
his/her possession until all work is completed.
Certain maintenance procedures may require power supply systems to be on.
These exceptions are clearly stated in the Maintenance Manual.
The illustrations show the power supply disconnector and its location.
‘
TechPub_2614345_0105 - MM_2864760_0102sp.fm
Residual Voltage
DANGER
Hazardous voltage.
Do not touch any terminals immediately after the power supply disconnector
is turned off. Ensure that no residual voltage remains on the capacitors
before touching. Wait five minutes. Failure to observe this information will
cause death or serious injury.
After the power supply disconnector is turned off, residual voltage remains
in the capacitor circuits.
ii - 36 (42) Doc. No. MM-2864760-0102

ii Safety Precautions Supply Systems
Electrical Cabinet
DANGER
Hazardous voltage.
Will shock, burn, or cause death. The power supply disconnector must be
turned off and secured with a lock before maintenance inside the electrical
cabinet.
Make sure that the electrical cabinet doors are closed after working inside the
electrical cabinet. Doors with lock must be locked.
The location of each electrical cabinet is shown by an arrow.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
A3/Flex TGA
Doc. No. MM-2864760-0102 ii - 37 (42)

Socket Outlet
WARNING
Hazardous voltage.
Can shock, burn, or cause death. Read the Maintenance Manual before
using this socket outlet.
The socket outlet (1) is connected to a residual current device (2) to protect
users against electrical shock if there is an earth fault in the connected
equipment. The residual current device shall be tested each time before the
socket outlet is being used. See the MM for test procedure.
The illustrations show the socket outlet, the residual current device, and their
location.
2 1
TechPub_2614345_0105 - MM_2864760_0102sp.fm
1 Socket outlet
2 Residual current device
ii - 38 (42) Doc. No. MM-2864760-0102

Air Supply
WARNING
Compressed air and moving machinery.
Close the main air valve and lock it before any maintenance.
Certain maintenance procedures may require air supply systems to be on.
The illustrations show the main air valve (1), the lock (2), and their location.
.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
1 Main air valve

2 Padlock
Doc. No. MM-2864760-0102 ii - 39 (42)

Steam Supply
WARNING
Hot steam can cause scalds.
Pressurized steam can be discharged unexpectedly. Close the steam supply
valve and lock it, depressurize and vent all steam safely before any
maintenance on parts with steam, such as pipes and valves.
Certain maintenance procedures may require steam supply systems to be on.
The illustrations show the steam supply valve (1), and its location.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
1 Steam supply valve
ii - 40 (42) Doc. No. MM-2864760-0102

Water Supply
CAUTION
Water under pressure.
Close the water supply valves before any maintenance.
Certain maintenance procedures may require water supply systems to be on.
The illustrations show the water supply valves (1) and (2), and their location.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
1
2
1 Water supply valve

2 Hot water supply valve
Doc. No. MM-2864760-0102 ii - 41 (42)

Equipment for Lifting and Moving
Loads ii Safety Precautions
Equipment for Lifting and Moving Loads

WARNING
Risk of crushing injury.
Make sure that the capacity of the lifting equipment is adequate and that the
equipment itself is in proper working order.
If lifting tackle must be joined to make up the necessary lengths, make sure
that the joints are secure and have the same lifting capacity as the rest of the
lifting tackle.
Always engage safety clips fitted to lifting hooks to prevent the lifting tackle
from slipping off.
Use ropes or poles to steady and manoeuvre suspended loads. Do not use
hands or feet.
Make sure that the route and destination are free from obstacles before
moving a suspended load. It must always be possible to quickly and safely
lower the load to the floor in an emergency.
When depositing loads, keep lifting tackle in place until the stability of the
load has been substantiated.
TechPub_2614345_0105 - MM_2864760_0102sp.fm
ii - 42 (42) Doc. No. MM-2864760-0102

1 Headspace Unit
TechPub_2614345_0103 - 01_MM2864760_02en.fm
Doc. No. MM-2864760-0102 1 - 1 (68)

1 Headspace Unit
Headspace by gas Injection - Description
SPC Reference 2636960-0200
Headspace by gas Injection can give between 2% and 10% free space inside
a package depending on the product being filled. The headspace is created by
blowing a controlled amount of sterile inert gas, air or nitrogen, directly onto
the product line.
The introduction of the HI line introduces a sterilisation process before the
production process and a cleaning process after.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1.2
1.4
1.5
1.1
1.3
1.1 Filling Pipe
1.2 Nozzle Unit
1.3 Heater
1.4 Spray Tank
1.5 Pneumatic Panel
1 - 2 (68) Doc. No. MM-2864760-0102

1 Headspace Unit Table of Contents
1 Headspace by gas Injection . . . . . . . . . . . . . . . . 1 - 5

1-1 Headspace by gas Injection - Function . . . . . . . . 1 - 5
1.1 Filling Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 8

1.1-1 Filling Pipe - Remove . . . . . . . . . . . . . . . . . . . . . 1 - 8
1.1-2 Filling Pipe - Fit . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 13
1.1-3 Filling Pipe - Set Position . . . . . . . . . . . . . . . . . 1 - 19
1.2 Nozzle Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 25

1.2-1 Nozzle Unit - Change O-rings and Diaphragm . 1 - 25
1.2-2 Nozzle Unit - Set Proximity Switches . . . . . . . . 1 - 30
1.2-3 Nozzle Unit - Clean Nozzle . . . . . . . . . . . . . . . . 1 - 35
1.2-4 Nozzle Unit - Check Thermocouple . . . . . . . . . 1 - 39
1.2-5 Nozzle Unit - Modify (from HI to HI bypassed) 1 - 40
1.3 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 43
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1.3-1 Heater - Check Peroxide Filter . . . . . . . . . . . . . . 1 - 43

1.3-2 Heater - Electrical Test . . . . . . . . . . . . . . . . . . . . 1 - 46
1.3-3 Heater - Check Thermocouples . . . . . . . . . . . . . 1 - 48
1.3-4 Heater - Check No-return Valve . . . . . . . . . . . . . 1 - 51
1.4 Spray Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 52

1.4-1 Spray Tank - Check . . . . . . . . . . . . . . . . . . . . . . 1 - 52
1.4-2 Spray Tank - Clean Peroxide Filter . . . . . . . . . . 1 - 53
1.4-3 Spray Tank - Clean Filter . . . . . . . . . . . . . . . . . . 1 - 54
1.4-4 Spray Tank - Set Pressure . . . . . . . . . . . . . . . . . . 1 - 55
1.5 Pneumatic Panel . . . . . . . . . . . . . . . . . . . . . . . . 1 - 56

1.5-1 Pneumatic Panel - Set Pressure Switch . . . . . . . 1 - 56
1.5-2 Pneumatic Panel - Check Flow Switch . . . . . . . 1 - 59
1.5-3 Pneumatic Panel - Change Filters . . . . . . . . . . . 1 - 60
1.5-4 Pneumatic Panel - Set I/P Transducer . . . . . . . . 1 - 61
1.6 Control Devices and Sensors. . . . . . . . . . . . . . 1 - 65

1.6.1 Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 65
1.6.1-1 Level Control - Description . . . . . . . . . . . . . . . . 1 - 65
Doc. No. MM-2864760-0102 1 - 3 (68)

Table of Contents 1 Headspace Unit
1.6.1-2 Level Control - Set . . . . . . . . . . . . . . . . . . . . . . 1 - 67
1.7 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 68
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 - 4 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1 Headspace by gas Injection
1 Headspace by gas Injection

1-1 Headspace by gas Injection - Function
General
The HI/CIP swing pipe must be moved to the PRODUCTION position for all
phases except when CIP is to be run.
The air or gas leaving the circulation heater is maintained at the correct
temperature by simultaneously adjusting the heater power and regulating the
amount of air or gas flowing through the heater. The flow is regulated by a
proportional control valve on the pneumatic panel.
Circuit component description
Component Function
Pneumatic panel Where the pressure and flow of the system air are
regulated.
Valve Y9101 Selects the system air for sterilisation or the inert
gas for the HI process
Proportional Valve C9115 Maintains the air or gas at the desired pressure
TechPub_2614345_0103 - 01_MM2864760_02en.fm
Valve Y9103 Turns the output of the valve panel ON and OFF
Heater Heats the air or inert gas to the correct
temperature.
Heats the peroxide to the correct temperature to
achieve sterilisation. This is done in a spiral wound
around the main heating element. This provides
isolation between the peroxide and the air/inert gas
circuit in the heater tank.
Valve F9106 Diverts the hot air or peroxide to the Aseptic
Chamber inlet connection to increase the flow
through the heater. This causes the temperature of
the air or peroxide to rise quickly.
Aseptic Chamber by-pass Entrance point for air or peroxide to Aseptic
connection Chamber
HI/CIP swing pipe Manual switch to clean the HI line
Valve F9105 Feeds the peroxide, air or inert gas to the HI nozzle
Nozzle Entry point into the product line
Valve Y9114 Used to empty the HI tank by blowing air into it.
(Cont'd)
Doc. No. MM-2864760-0102 1 - 5 (68)

1 Headspace by gas Injection 1 Headspace Unit
(Cont'd)
Component Function
HI peroxide spray tank Used to store peroxide for the Spraying phase of
Sterilisation
Valve Y9112 Used to drain the HI tank or feed the contents of the
HI tank to the heater.
Level regulating valve Regulates the product flow
Product valve group Selects the Product or the CIP cleaning fluid and
sterile air.
Flow meter B9117 Checks the right amount of air flow through the
circuit
Flow switch B9118 Checks for the right amount of air flow through the
by-pass circuit
(Cont'd)
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 - 6 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1 Headspace by gas Injection
(Cont'd)
Circuit Overhead
25 24 22 26
21
23
13 14
15
11 12 20
16
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2 4 10 9 19
7 17 18
1 3 5 6 8
1 Pneumatic panel 14 Low level sensor

2 Filling gas selection valve Y9101 15 Superheater temperature probe B9121
3 Filtering section 16 Heater
4 Pressure switch B9104 17 Air temperature probe B9122
5 Proportional Valve C9115 18 Stainless steel filter
6 Flow meter B9117 19 HI by-pass valve F9106
7 Flow switch B9118 20 HI/CIP switch
8 HI main valve Y9103 21 HI circuit temperature probe B9106
9 Peroxide tank 22 HI injection valve F9105
10 Drain/spray valve Y9114 23 Nozzle
11 HI spray tank 24 Regulating valve
12 Filling/emptying valve Y9112 25 Product valve group
13 High level sensor 26 Aseptic Chamber by-pass connection
Doc. No. MM-2864760-0102 1 - 7 (68)

1.1 Filling Pipe 1 Headspace Unit
1.1 Filling Pipe

1.1-1 Filling Pipe - Remove

Machine Status Mains Power OFF
Air OFF
Steam ON
Water OFF
a) Remove the stop pin (1) and the lower part of the filling pipe (2).
b) Change the O-ring (3).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2
1 Stop pin
2 Filling pipe
3 O-ring
(Cont'd)
1 - 8 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.1 Filling Pipe
(Cont'd)
c) Open the LS inductor (4) by turning the knob (5).
d) Pull up the knob (6) and open the lower forming ring (7).
e) Remove the pressure roller assembly (8) from the filling pipe.
f) Pull down the knob (9) and open the upper forming ring (10).
5 4
10
6
TechPub_2614345_0103 - 01_MM2864760_02en.fm
4 LS inductor 8 Pressure roller assembly

5 Knob 9 Knob
6 Knob 10 Upper forming ring
7 Lower forming ring
(Cont'd)
Doc. No. MM-2864760-0102 1 - 9 (68)

(Cont'd)
g) Remove the wing nut (11) and the cover (12).
h) Disconnect the hose from the bulkhead lead-in (13).
i) Loosen the clamping piece (14).
12
11
11
13
TechPub_2614345_0103 - 01_MM2864760_02en.fm
14
11 Wing nut
12 Cover
13 Bulkhead lead-in
14 Clamping piece
(Cont'd)
1 - 10 (68) Doc. No. MM-2864760-0102

(Cont'd)
Note! Take care of the gaskets (20) and the O-ring (21). Change them
if necessary.
j) Loosen the locking devices (15) and remove the product pipe (16) with
the pneumatic valve (17) assembled.
k) Fit the plug (18) on the pipe (19) by tightening the clamping piece (14).
18 14
19
TechPub_2614345_0103 - 01_MM2864760_02en.fm
20
20
16
15
17 15
21
14 Clamping piece
15 Locking device
16 Product pipe
17 Pneumatic valve
18 Plug
19 Pipe
20 Gasket
21 O-ring
(Cont'd)
Doc. No. MM-2864760-0102 1 - 11 (68)

(Cont'd)
l) With one hand firmly holding the filling pipe (22), undo the locking
handles (23).
m) Remove the filling pipe (22) and store it in a safe place.
23
23
22
TechPub_2614345_0103 - 01_MM2864760_02en.fm
22 Filling pipe
23 Locking handle
1 - 12 (68) Doc. No. MM-2864760-0102

1.1-2 Filling Pipe - Fit

Air OFF
Steam ON
Water OFF
a) Pull down the knob (1) and open the upper forming ring (2).
b) Open the LS inductor (3) by turning the knob (4).
c) Pull up the knob (5) and open the lower forming ring (6).
4
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Knob
2 Upper forming ring
3 LS inductor
4 Knob
5 Knob
(Cont'd)
Doc. No. MM-2864760-0102 1 - 13 (68)

(Cont'd)
d) Fit the filling pipe (7) and secure it in to position with the locking
handles (8).
e) Mount the pressure roller assembly (9) on to the filling pipe (7).
8 Single pressure roller

is shown
8
9
TechPub_2614345_0103 - 01_MM2864760_02en.fm
7 Filling pipe
8 Locking handle
9 Pressure roller assembly
(Cont'd)
1 - 14 (68) Doc. No. MM-2864760-0102

(Cont'd)
f) Pull down the knob (1) and close the upper forming ring (2).
g) Close the LS inductor (3) by turning the knob (4).
h) Pull up the knob (5) and close the lower forming ring (6).
1
3
TechPub_2614345_0103 - 01_MM2864760_02en.fm
5 6
1 Knob
2 Upper forming ring
3 LS inductor
4 Knob
5 Knob
6 Forming ring
(Cont'd)
Doc. No. MM-2864760-0102 1 - 15 (68)

(Cont'd)
i) Loosen the clamping piece (10) and remove the plug (11).
j) Fit the product pipe (12) with the gaskets (13) by the locking
devices (14).
k) Fit the O-ring (15) on the pneumatic valve (16).
l) Connect the pneumatic valve (16) to the pipe (17) by the clamping
piece (10).
11 10
17
TechPub_2614345_0103 - 01_MM2864760_02en.fm
13
13
12
14
16 14
15
10 Clamping piece
11 Plug
12 Product pipe
13 Gasket
14 Locking device
15 O-ring
16 Pneumatic valve
17 Pipe
(Cont'd)
1 - 16 (68) Doc. No. MM-2864760-0102

(Cont'd)
m) Connect the air hose from the pneumatic valve (16) to the bulkhead lead-
in (18).
n) Fit the cover (19) by means of the wing nuts (20).
19
20
20
18
16
TechPub_2614345_0103 - 01_MM2864760_02en.fm
16 Pneumatic valve
18 Bulkhead lead-in
19 Cover
20 Wing nut
(Cont'd)
Doc. No. MM-2864760-0102 1 - 17 (68)

(Cont'd)
o) Fit the O-ring (21) in its seat on the upper part of the filling pipe (22).
p) Fit the lower part of the filling pipe (23) and secure it in to position with
the locking device (24).
21
22
24
23
TechPub_2614345_0103 - 01_MM2864760_02en.fm
21 O-ring
22 Filling pipe, upper part
23 Filling pipe, lower part
24 Locking device
1 - 18 (68) Doc. No. MM-2864760-0102

1.1-3 Filling Pipe - Set Position

Machine Status PREPARATION
Note! For volume dependent template and tool codes, see 10.2
Templates and Tools in the MM for the Filling Machine.
a) Swing out the design correction photocell holder (1).
1
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Photocell holder
(Cont'd)
Doc. No. MM-2864760-0102 1 - 19 (68)

(Cont'd)
b) Remove the cover (2) by the wing nuts (3).
c) Disconnect the hose of the pneumatic valve (4) from the bulkhead lead-
in (5).
d) Remove the clamping piece (6).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
6
2 Cover
3 Wing nut
4 Pneumatic valve
5 Bulkhead lead-in
6 Clamping piece
(Cont'd)
1 - 20 (68) Doc. No. MM-2864760-0102

(Cont'd)
Note! Take care of the gaskets (11) and the O-ring (12). Change them
if necessary.
e) Loosen the locking devices (7) and remove the product pipe (8) with the
pneumatic valve (4) assembled.
f) Fit the plug (9) on the pipe (10) by tightening the clamping piece (6).
9 6
10
4 11
TechPub_2614345_0103 - 01_MM2864760_02en.fm
11
7
7
12
4 Pneumatic valve
6 Clamping piece
7 Locking device
8 Product pipe
9 Plug
10 Pipe
11 Gasket
12 O-ring
(Cont'd)
Doc. No. MM-2864760-0102 1 - 21 (68)

(Cont'd)
Note! The lower forming ring (13) must be in its closed position. Put a
double piece of packaging material between the pressure roller and
the counter roller, see 1.5.1-5 Filling Pipe - Set Pressure Roller in the
MM for the Filling Machine.
g) Check that the seal (14) between the mounting plate (15) and the
fastening plate (16) is compressed to dimension A.
Note! It is important to set the distance A correctly.
16 14 A 15
A = 6.0 ±0.5 mm
TechPub_2614345_0103 - 01_MM2864760_02en.fm
13

14 Seal
15 Mounting plate
16 Fastening plate
(Cont'd)
1 - 22 (68) Doc. No. MM-2864760-0102

(Cont'd)
h) Centre the support rollers (17), see 4-21 Jaw System - Set Support
Rollers in the MM for the Filling Machine.
i) Fit the O-ring (18) on the template (19).
j) Fit the template (19) on the flange (20).
k) Check that the filling pipe (21) and the template (19) are centred with
respect to the support rollers (17). If the filling pipe is not correctly
centred, continue with item l).
21
20
18
TechPub_2614345_0103 - 01_MM2864760_02en.fm
19
17 21 19 17
Stand Alone
Volume Shown
18
17 Support roller
19 18 O-ring
19 Template
20 Flange
21 Filling pipe
(Cont'd)
Doc. No. MM-2864760-0102 1 - 23 (68)

(Cont'd)
l) On the fastening plate (16), loosen the lock nuts on the screws (22)
and (23). Loosen the screws (22) a few turns.
m) Align and centre the filling pipe to the template using the screws (23)
and (24). Do not over tighten the screws (24). Lock in position with the
lock nuts on screws (23) and (24).
n) Tighten the screws (22) on the fastening plate (16) until they just touch
the mounting plate (15). Do not over tighten. Lock the screws (22) with
the lock nuts.
o) Check that:
– the gasket compression is according to item g). If it is not correct,
reset it and proceed from item m).
– the spring load is correct, see 1.5.1-5 Filling Pipe - Set Pressure
Roller. in the MM for the Filling Machine. Adjust if necessary
– the filling pipe alignment is according to step k).
p) Assemble in the reverse order.
16
TechPub_2614345_0103 - 01_MM2864760_02en.fm
15
22
22
24
24
22
21 23
23 15 Mounting plate
16 Fastening plate
22 Screw
23 Screw
24 Screw
1 - 24 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.2 Nozzle Unit
1.2 Nozzle Unit

1.2-1 Nozzle Unit - Change O-rings and Diaphragm

s

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
Parts may be hot. Follow the Safety Precautions.
WARNING
Hydrogen peroxide!
Follow the Safety precautions.
(Cont'd)
TechPub_2614345_0103 - 01_MM2864760_02en.fm
Doc. No. MM-2864760-0102 1 - 25 (68)

1.2 Nozzle Unit 1 Headspace Unit
(Cont'd)
a) Remove the cover (1) by the wing nuts (2).
b) Remove the clamps (3).
c) Remove the pipe (4) and change the O-rings (5).
2
1
2
3
5
TechPub_2614345_0103 - 01_MM2864760_02en.fm
4
3
5
1 Cover
2 Wing nut
3 Clamp
4 Pipe
5 O-ring
(Cont'd)
1 - 26 (68) Doc. No. MM-2864760-0102

(Cont'd)
d) Remove the clamp (6) and the pneumatic valve (7).
e) Remove the nozzle (8) and change the O-rings (9) and (10).
f) Remove the blind plug (11) by loosening the clamping piece (12) and
change the O-ring (13).
6 7
10
TechPub_2614345_0103 - 01_MM2864760_02en.fm
12
6 Clamp
7 Pneumatic valve
8 Nozzle
9 O-ring
10 O-ring
11 Blind plug
13
12 Clamping piece 11
13 O-ring
(Cont'd)
Doc. No. MM-2864760-0102 1 - 27 (68)

(Cont'd)
g) Loosen the clamping pieces (14) and slightly pull back the pipes (15)
and (16).
h) Change the O-rings (17) and (18).
i) Fit back the pipes (15) and (16) and tighten the clamping pieces (14).
15 14 17
16 14 18
TechPub_2614345_0103 - 01_MM2864760_02en.fm
14 Clamping piece
15 Pipe
16 Pipe
17 O-ring
18 O-ring
(Cont'd)
1 - 28 (68) Doc. No. MM-2864760-0102

(Cont'd)
Note! When assembling the actuators (20) and (23), make sure that
the shutter rim (24) is aligned with the milling (25) of the valve body.
j) Remove the screws (19) and the actuator (20) from the valve body (21).
Change the diaphragms (22).
k) Repeat the same procedure on the other actuator (23).
l) Assemble in the reverse order.
20
22
19
24 25
21
TechPub_2614345_0103 - 01_MM2864760_02en.fm
23
19 Screw
20 Actuator
21 Valve body
22 Diaphragm
23 Actuator
24 Shutter rim
25 Milling
Doc. No. MM-2864760-0102 1 - 29 (68)

1.2-2 Nozzle Unit - Set Proximity Switches

Air OFF
Steam ON
Water OFF
Product Pipe Fitted

Set the distance A between the end of the proximity switch (1) and the
bracket (2) on the product pipe (3).
Check that the proximity switch (1) functions correctly.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
A
A = 0.5 ±0.1 mm
3 2 1
1 Proximity switch
2 Bracket
3 Product pipe
(Cont'd)
1 - 30 (68) Doc. No. MM-2864760-0102

(Cont'd)
HI ON
Set the distance A between the end of the proximity switch (1) and the flat
surface of the valve body (2).
A
A = 0.5 ±0.1 mm
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2 1
1 Proximity switch
2 Valve body
(Cont'd)
Doc. No. MM-2864760-0102 1 - 31 (68)

(Cont'd)
CIP Cleaning
a) Swing the pipe (1) into the CIP position as shown and fit the plug (2) to
prevent the ingress of dirt.
b) Set the distance A between the end of the proximity switch (3) and the
bracket (4) on the pipe (1).
c) Check that the proximity switch (3) functions correctly.
2
3
TechPub_2614345_0103 - 01_MM2864760_02en.fm
A = 0.5 ±0.1 mm
1 Pipe
2 Plug
3 Proximity switch
4 Bracket
(Cont'd)
1 - 32 (68) Doc. No. MM-2864760-0102

(Cont'd)
Production
a) Swing the pipe (1) into the PRODUCTION position as shown and fit the
plug (2) to prevent the ingress of dirt.
b) Set the distance A between the end of the proximity switch (3) and the
bracket (4) on the pipe (1).
c) Check that the proximity switch (3) functions correctly.
3 2
TechPub_2614345_0103 - 01_MM2864760_02en.fm
A = 0.5 ±0.1 mm
1 Pipe
2 Plug
3 Proximity switch
4 Bracket
(Cont'd)
Doc. No. MM-2864760-0102 1 - 33 (68)

(Cont'd)
Plug in Position
Set the distance A between the end of the proximity switch (1) and the
bracket (2) on the plug (3).
3 1
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2
A = 0.5 ±0.1 mm
1 Proximity switch
2 Bracket
3 Plug
1 - 34 (68) Doc. No. MM-2864760-0102

1.2-3 Nozzle Unit - Clean Nozzle

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
WARNING
Hydrogen peroxide!
(Cont'd)
TechPub_2614345_0103 - 01_MM2864760_02en.fm
Doc. No. MM-2864760-0102 1 - 35 (68)

(Cont'd)
a) Remove the wing nuts (1) and the cover (2).
b) Remove the clamping piece (3).
c) Disconnect the hose (4).
2
1
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Wing nut
2 Cover
3 Clamping piece
4 Hose
(Cont'd)
1 - 36 (68) Doc. No. MM-2864760-0102

(Cont'd)
d) Loosen the clamp (5) and remove the pneumatic valve (6) taking care of
the O-ring (7).
e) Fit the plug (8) by the clamping piece (3).
f) Remove the nozzle (9) and the O-rings (10) and (11).
5 10
8 9
11
3
TechPub_2614345_0103 - 01_MM2864760_02en.fm
3 Clamping piece
5 Clamp
6 Pneumatic valve
7 O-ring
8 Plug
9 Nozzle
10 O-ring
11 O-ring
(Cont'd)
Doc. No. MM-2864760-0102 1 - 37 (68)

(Cont'd)
CAUTION
Risk of damage to the equipment.
Clean the nozzle using a wire (12) suitable for the hole in order to not
modify the nozzle hole size.
g) By means of a measured wire (12), clean the nozzle hole from the
residues.
h) Clean the nozzle (9) and the O-rings (10) and (11) with alkali solution.
After cleaning rinse with drinking water.
i) When the nozzle (9) is dry, hold it up to the light and check that there are
no residues blocking the nozzle.
j) Assemble in the reverse order.
10
TechPub_2614345_0103 - 01_MM2864760_02en.fm
9
11
12
9 Nozzle
10 O-ring
11 O-ring
12 Wire
1 - 38 (68) Doc. No. MM-2864760-0102

1.2-4 Nozzle Unit - Check Thermocouple

Air OFF
Steam ON
Water OFF
Note! Perform this check to ensure that the measurement of the

temperature value is not affected by environmental conditions.
Check that the end of the thermocouple (1) on the HI pipe (2) is completely
covered by the clamp (3).
2
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2 1
1 Thermocouple
2 HI pipe
3 Clamp
Doc. No. MM-2864760-0102 1 - 39 (68)

1.2-5 Nozzle Unit - Modify (from HI to HI bypassed)

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
Note! The following volumes must run always with HI enabled: TPA
200 Sq, TPA 250 Sq, TPA 330 Sq, TPA 500 Sq, TPA 750Sq, TPA
1000 Sq, TBA 1890 S and TBA 2000 S.
a) Remove the wing nut (1) and the cover (2).

b) Disconnect the pneumatic valve hose from the bulkhead lead-in (3).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2
1 Cover
2 Wing nut
3 Bulkhead lead-in
(Cont'd)
1 - 40 (68) Doc. No. MM-2864760-0102

(Cont'd)
c) Loosen the clamping piece (4).
d) Loosen the locking devices (5) and remove the product pipe (6) with the
pneumatic valve (7) assembled taking care of the O-ring (8).
e) Fit the plug (9) on the HI pipe (10) by tightening the clamping piece (4).
f) Change the gaskets (11).
9 4
10
7
TechPub_2614345_0103 - 01_MM2864760_02en.fm
11 11
6
5
5
8
4 Clamping piece
5 Locking device
6 Product pipe
7 Pneumatic valve
8 O-ring
9 Plug
10 HI pipe
11 Gasket
(Cont'd)
Doc. No. MM-2864760-0102 1 - 41 (68)

(Cont'd)
g) Fit the product pipe (12) for HI bypassed by tightening the locking
devices (13).
h) Fit the covering panel (14) for HI bypassed by the screws (15) and the
clamps (16).
Note! Follow the reverse order to modify from HI bypassed to HI.
15
13
14
TechPub_2614345_0103 - 01_MM2864760_02en.fm
15 16 13
12
12 Product pipe
13 Locking device
14 Covering panel
15 Screw
16 Clamp
1 - 42 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.3 Heater
1.3 Heater
1.3-1 Heater - Check Peroxide Filter

Air OFF
Steam ON
Water OFF
WARNING
Hydrogen peroxide!
WARNING
Burn hazard.
The heater may be extremely hot. Always wear personal protective
equipment and wait for the heater to cool down before performing the
following procedure.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
Note! The procedure to clean the peroxide filter is for customers with
a laboratory or facilities for performing the task.
(Cont'd)
Doc. No. MM-2864760-0102 1 - 43 (68)

1.3 Heater 1 Headspace Unit
(Cont'd)
a) Carefully remove the cap (1) from the housing (2).
b) Remove the filter element (3) and O-ring (4) from the housing (2).
c) Change the filter or clean it according to the Cleaning Procedure on the
following page.
d) Assemble in the reverse order.
4 2
TechPub_2614345_0103 - 01_MM2864760_02en.fm
3
1
1 Cap
2 Housing
3 Filter element
4 O-ring
(Cont'd)
1 - 44 (68) Doc. No. MM-2864760-0102

(Cont'd)
Cleaning Procedure
Note! Dispose the nitric acid solution according to the local
legislation.
a) In a beaker and under a gas exhauster, prepare approximately 50 ml of

Nitric Acid (HNO3) at a concentration of 10 to 15% by weight.
b) Place the beaker on a magnet stirrer with a heater.
c) Immerse the filter element in to the solution.
d) Heat the HNO3 solution to 60°C for 20 minutes stirring continually.
e) Using a pair of pliers, carefully remove the filter element from the
solution and rinse it well with distilled water.
Note! Use a 60 micron filter element.

TechPub_2614345_0103 - 01_MM2864760_02en.fm
Doc. No. MM-2864760-0102 1 - 45 (68)

1.3-2 Heater - Electrical Test

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
If the heater does not reach the required temperature, check the heater is
working properly by performing the following electrical test.
(Cont'd)
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 - 46 (68) Doc. No. MM-2864760-0102

(Cont'd)
Remove the screws (1) and open the plug (2), then using a tester measure the
following resistance values:
– between the “phase” (3) and the “neutral” (4) electrical terminals the
value must be about 24 Ohm.
– between the “phase” (3) electrical terminal and the heater flange (5)
the value must be more than 1 MOhm.
– between the “neutral” (4) electrical terminal and the heater flange (5)
the value must be more than 1MOhm.
1
2
5
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Screw
2 Plug
3 Phase terminal
4 Neutral terminal
5 Flange
Doc. No. MM-2864760-0102 1 - 47 (68)

1.3-3 Heater - Check Thermocouples

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
Note! Perform this check when the heater does not reach the
temperature required.
(Cont'd)
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 - 48 (68) Doc. No. MM-2864760-0102

(Cont'd)
a) Remove the screws (1) and the heating element (2).
b) Check that the end of the thermocouple (3) is in contact with the heating
element (2), inside the welded plate (4).
1 3
3
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Screw
2 Heating element
3 Thermocouple
4 Plate
(Cont'd)
Doc. No. MM-2864760-0102 1 - 49 (68)

(Cont'd)
c) Check that the end of the thermocouple (5) is in the centre of the air
outlet pipe (6).
d) Change the gaskets (7) and (8).
e) Assemble in the reverse order.
Note! Change always the gaskets (7) and (8) when disassembling the
heating element.
6 5
TechPub_2614345_0103 - 01_MM2864760_02en.fm
8
5 Thermocouple
6 Outlet pipe
7 Gasket
8 Gasket
1 - 50 (68) Doc. No. MM-2864760-0102

1.3-4 Heater - Check No-return Valve

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
a) Loosen the nuts (1) and remove the no-return valve (2).
b) Carefully remove the cap (3).
c) Check that the needle (4) is clean and goes easily up and down.
d) Clean the no-return valve or change it if necessary.
e) Assemble in the reverse order.
f) Repeat the same procedure for the valve (5).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
4
2 5
1 Nut
2 No-return valve
3 Cap
4 Needle
5 Valve
Doc. No. MM-2864760-0102 1 - 51 (68)

1.4 Spray Tank 1 Headspace Unit
1.4 Spray Tank

1.4-1 Spray Tank - Check

Air OFF
Steam ON
Water OFF
WARNING
Hydrogen peroxide!
Note! Mark all connections before removal.
Check for peroxide leakages in the spray unit. Change the O-rings indicated
by the arrow if damaged or worn.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 - 52 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.4 Spray Tank
1.4-2 Spray Tank - Clean Peroxide Filter

Air OFF
Steam ON
Water OFF
WARNING
Hydrogen peroxide!
a) Remove the screws (1) and the filter housing (2).

b) Pull out the peroxide filter (3), rinse it with deionized water and clean it
with compressed air.
c) If required change the peroxide filter (3).
d) Fit the peroxide filter (3) and the filter housing (2).
e) Tighten the screws (1).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1
2
1 Screw
2 Filter housing
3 Peroxide filter
Doc. No. MM-2864760-0102 1 - 53 (68)

1.4 Spray Tank 1 Headspace Unit
1.4-3 Spray Tank - Clean Filter

Air OFF
Steam ON
Water OFF
WARNING
Hydrogen peroxide!
a) Disconnect the air pipe (1) from the filter group (2).
b) Remove the filter group (2).
c) Remove the filter (3) from the filter house (4).
d) Clean the filter (3) with compressed air.
e) Check the O-rings (5) for wear and/or damage and change if required.
Note! While assembling make sure that the O-rings (5) are correctly
assembled.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
f) Assemble in the reverse order.
5
4
2 5
3
1 Air pipe
2 Filter group
3 Filter
4 Filter house
5 O-ring
1 - 54 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.4 Spray Tank
1.4-4 Spray Tank - Set Pressure

Machine Status PREPARATION
2640820-0100
Using the pressure regulator (1) on the valve panel, set the HI spray system
air pressure, see the 1.7 Technical data.
1
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Pressure regulator
Doc. No. MM-2864760-0102 1 - 55 (68)

1.5 Pneumatic Panel 1 Headspace Unit
1.5 Pneumatic Panel

1.5-1 Pneumatic Panel - Set Pressure Switch

Machine Status Mains Power ON
Air ON
Steam ON
Water OFF
WARNING
Burn hazard.
The pneumatic panel is located close to the heater, which may be
extremely hot. Always wear personal protective equipment and wait
for the heater to cool down before performing the following procedure.
a) In the service unit, turn the pressure regulator (1) until the pressure
gauge (2) shows 5.5 bar (0.5MPa).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2
2 Pressure gauge
(Cont'd)
1 - 56 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.5 Pneumatic Panel
(Cont'd)
b) Loosen the grub screw (3) and then turn the adjusting screw (4) fully
counter-clockwise.
c) Turn the adjusting screw (4) slowly clockwise until the HI/N2 alarm
starts to flash on the TPOP and then tighten the grub screw (3).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
4
3
3 Grub screw
4 Adjusting screw
(Cont'd)
Doc. No. MM-2864760-0102 1 - 57 (68)

(Cont'd)
d) Turn the pressure regulator (1) until the pressure gauge (2) shows the
correct air pressure for the machine, see chapter 10.1 Technical data in
the MM for the Filling Machine.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
2 Pressure gauge
1 - 58 (68) Doc. No. MM-2864760-0102

1.5-2 Pneumatic Panel - Check Flow Switch

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
Check on the flow switch (1) that the arrow on the movable body (2) is
aligned to the arrow of the setting label, as shown below. If not, adjust the
position of the movable body (2) by the screw (3).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1 Flow switch
2 Movable body
3 Screw 2
Doc. No. MM-2864760-0102 1 - 59 (68)

1.5-3 Pneumatic Panel - Change Filters

Air OFF
Steam ON
Water OFF
WARNING
Burn hazard.
Note! There may be nitrogen under pressure in the circuit. Close the
nitrogen supply before removing the filters.
Remove and change the filter inserts from the filter housings (1), (2) and (3).
TechPub_2614345_0103 - 01_MM2864760_02en.fm
1
1 Filter housing section

1 - 60 (68) Doc. No. MM-2864760-0102

1.5-4 Pneumatic Panel - Set I/P Transducer

Air ON
Steam ON
Water OFF
Navigate the transducer interface using the buttons explained in the table
below.
Button Function
OK (5) enter the menu from the default screen
move to the next level of the menu structure
accept changes within the functions
CANCEL (6) move back through the levels of the menu structure
cancel changes within the functions
UP (1)/DOWN (3) move between menu options within a level
set digit values within the functions
LEFT (4)/RIGHT (2) move between digits within the functions
TechPub_2614345_0103 - 01_MM2864760_02en.fm
OK C
1
4 2
3
5 4 3 1 2 6
1 UP button
2 RIGHT button
3 DOWN button
4 LEFT button
5 OK button
6 CANCEL button
(Cont'd)
Doc. No. MM-2864760-0102 1 - 61 (68)

(Cont'd)
a) Press the OK button (5). The display (7) shows Password OK?.
b) Enter the password, 2121, by means of the UP (1), RIGHT (2),
DOWN (3) and LEFT (4) buttons. The display (7) shows Display Setup.
c) Press the DOWN button (3). The display (7) shows Offline Setup.
d) Press the OK button (5). The display (7) shows Min Setup.
e) Press the OK button (5). The display (7) shows 00.0 bar 00.0V.
f) Press the OK button (5). The display (7) shows Warning P2 Shift.
g) Press the OK button (5). The display (7) shows Min Setup.
h) Press the DOWN button (3). The display (7) shows Max Setup.
i) Press the OK button (5). The display (7) shows 06.0 bar 10.0V.
j) Press the OK button (5). The display (7) shows Warning P2 Shift.
k) Press the OK button (5). The display (7) shows Max Setup.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
OK C
1
4 2
3
5 4 3 1 2
1 UP button
2 RIGHT button
3 DOWN button
4 LEFT button
5 OK button
7 Display
(Cont'd)
1 - 62 (68) Doc. No. MM-2864760-0102

(Cont'd)
l) Press the DOWN button (3). The display (7) shows Speed Setting.
m) Press the OK button (5). Set the value to 0 by means of the Up (1) and
DOWN (3) buttons.
n) Press the OK button (5). The display (7) shows Speed Setting.
o) Press the DOWN button (3).
– if the display (7) shows Dither Amp, continue with items p) to y).
– if the display (7) shows Dynamic Response, continue with items z)
to af).
p) Press the OK button (5). Set the value to 1 by means of the UP (1) and
DOWN (3) buttons.
q) Press the OK button (5). The display (7) shows Dither Amp.
r) Press the DOWN button (3). The display (7) shows Prop Gain.
s) Press the OK button (5). Set the value to 7 by means of the UP (1) and
DOWN (3) buttons.
t) Press the OK button (5). The display (7) shows Prop Gain.
u) Press the DOWN button (3). The display (7) shows Int Gain.
v) Press the OK button (5). Set the value to 2 by means of the UP (1) and
TechPub_2614345_0103 - 01_MM2864760_02en.fm
DOWN (3) buttons.
OK C
1
4 2
3
1 UP button
3 DOWN button
5 OK button
7 Display 5 3 1
(Cont'd)
Doc. No. MM-2864760-0102 1 - 63 (68)

(Cont'd)
w) Press the OK button (5). The display (7) shows Int Gain.
x) Press the CANCEL button (6).The display (7) shows Offline Setup.
y) Press the CANCEL button (6). The display (7) shows 00.0 bar 00.0V.
z) Press the OK button (5). Set the value to 2 by means of the UP (1) and
DOWN (3) buttons.
aa) Press the OK button (5). The display (7) shows Dynamic Response.
ab) Press the DOWN button (3). The display (7) shows Dither Amp.
ac) Press the OK button (5). Set the value to 1 by means of the UP (1) and
DOWN (3) buttons.
ad) Press the OK button (5). The display (7) shows Dither Amp.
ae) Press the CANCEL button (6).The display (7) shows Offline Setup.
af) Press the CANCEL button (6). The display (7) shows 00.0 bar 00.0V.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
OK C
1
4 2
3
5 3 1 6
1 UP button
3 DOWN button
5 OK button
6 CANCEL button
7 Display
1 - 64 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.6 Control Devices and Sensors
1.6 Control Devices and Sensors

1.6.1 Level Control

1.6.1-1 Level Control - Description
The level regulator relay A308 monitors the product level by measuring the
change in resistance of immersed and non immersed electrodes. The relay
sensitivity must be set according to the conductivity of the product.
A300
A301
A302
A303
A304
A308
TechPub_2614345_0103 - 01_MM2864760_02en.fm
A 300: Hydrogen peroxide bath

A 301: Hydrogen peroxide spray tank
A 302: Water separator
A 303: Cooling water
A 304: Regulating valve leakage
A 308: HI level peroxide spray tank
(Cont'd)
Doc. No. MM-2864760-0102 1 - 65 (68)

1.6 Control Devices and Sensors 1 Headspace Unit
(Cont'd)
The level regulator parameters are set using the potentiometer and selectors
shown in the illustration below:
a) The selector (2) sets the filling/empty functionality.
– In the EMPTY FUNCTION position is the output relay activated
when the high level electrode is immersed and deactivated when the
low level electrode is “dry”.
– In the FILL FUNCTION position is the output relay activated when
the low level electrode is “dry” and deactivated when the high level
electrode is immersed.
b) The potentiometer (3) fine adjusts the sensitivity as a percentage (%) of
the sensitivity range (4).
c) The potentiometer sets the delay.
d) The selector (4) sets ON the level status of the relay and the sensitivity
range.
e) The yellow LED (5) lights up when the relay is CLOSED.
f) The green LED (6) lights up when the power is ON.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
t
RM4LA
Empty Fill
0.1 function
function
KΩ
t
RM4LA
0.1
10 3
KΩ
10
x..% x..%
R
U
Function/Range 2
50 5 R
U
6 Function/Range 4
50
8 Functionality selector
9 Fine adjustment potentiometer
10 Function mode selector and sensitivity
11 Yellow LED
12 Green LED
1 - 66 (68) Doc. No. MM-2864760-0102

1 Headspace Unit 1.6 Control Devices and Sensors
1.6.1-2 Level Control - Set

Air ON
Steam ON
Water ON
Set the display functions, see table below, with a screwdriver:
Description Time R-value Functionality Function/

value (1) (2) sector(3) range (4)
Level HI spray A308 0 20
tank 50
Note! The functionality selector (3) is recommended to always be set

according to the table to avoid problems.
If required, fine adjust by means of the potentiometer (2).

Make sure that the yellow LED (5) lights up when the level is obtained.
TechPub_2614345_0103 - 01_MM2864760_02en.fm
t
1 RM4LA
0.1
2
KΩ
10
x..%
3
R
U
Function/Range
50 4
1 Adjustment of timing
2 Fine adjustment potentiometer
3 Functionality selector
4 Function mode selector and sensitivity
5 Yellow LED
Doc. No. MM-2864760-0102 1 - 67 (68)

1.7 Technical Data 1 Headspace Unit
1.7 Technical Data

Process phase Unit Location Value
Preparation Air flow Nozzle 0.3 3 - 6 l/min
Nozzle 0.4 4.4 - 7.5 l/min
Nozzle 0.5 7.8 - 13 l/min
Nozzle 0.6 13.5 - 20 l/min
Heat sterilization Air pressure Gas circuit 5 - 6 bar
(0.5 - 0.6 MPa)
End of heat Air temperature Heater output 370°C
sterilization
Spraying Air pressure Spraying circuit 3 bar
(0.3 Mpa)
End of spraying H2O2 temperature Nozzle input 25º C over the
temperature
recorded at the
beginning of step
SPRAYING.
Drying Air temperature Heater output 300ºC - 360º C
(0-120 sec.)
330ºC - 360º C
(rest of Drying)
TechPub_2614345_0103 - 01_MM2864760_02en.fm
Production Air/N2 pressure Gas circuit Dependent upon
product and
amount of
headspace
Air/N2 temperature Heater output 330°C - 360°C
Air/N2 flow Gas circuit Dependent upon
product and
amount of
headspace
Cleaning Cleaning agent Nozzle input Temperature of
temperature CIP
All phases Temperature Heating element <720°C
1 - 68 (68) Doc. No. MM-2864760-0102

Index of Procedures
F
Filling Pipe - Fit . . . . . . . . . . . . . . . . . . . . . . . 1 - 13
Filling Pipe - Remove . . . . . . . . . . . . . . . . . . . . 1 - 8
Filling Pipe - Set Position . . . . . . . . . . . . . . . . 1 - 19
H
Headspace by gas Injection - Function . . . . . . 1 - 5
Heater - Check No-return Valve . . . . . . . . . . . 1 - 51
Heater - Check Peroxide Filter . . . . . . . . . . . . 1 - 43
Heater - Check Thermocouples . . . . . . . . . . . 1 - 48
Heater - Electrical Test . . . . . . . . . . . . . . . . . 1 - 46
L
Level Control - Description . . . . . . . . . . . . . . . 1 - 65
Level Control - Set . . . . . . . . . . . . . . . . . . . . . 1 - 67
TechPub_2614345_0103 - MM_2864760_0102IOM.fm
N
Nozzle Unit - Change O-rings and Diaphragm 1 - 25
Nozzle Unit - Check Thermocouple . . . . . . . . 1 - 39
Nozzle Unit - Clean Nozzle . . . . . . . . . . . . . . 1 - 35
Nozzle Unit - Modify (from HI to HI bypassed) 1 - 40
Nozzle Unit - Set Proximity Switches . . . . . . . 1 - 30
P
Pneumatic Panel - Change Filters . . . . . . . . . 1 - 60
Pneumatic Panel - Check Flow Switch . . . . . 1 - 59
Pneumatic Panel - Set I/P Transducer . . . . . . 1 - 61
Pneumatic Panel - Set Pressure Switch . . . . 1 - 56
S
Spray Tank - Check . . . . . . . . . . . . . . . . . . . . 1 - 52
Spray Tank - Clean Filter . . . . . . . . . . . . . . . . 1 - 54
Spray Tank - Clean Peroxide Filter . . . . . . . . 1 - 53
Spray Tank - Set Pressure . . . . . . . . . . . . . . . 1 - 55
Doc. No. MM-2864760-0102 iii - 1

Index of Procedures
TechPub_2614345_0103 - MM_2864760_0102IOM.fm
iii - 2 Doc. No. MM-2864760-0102

30mm Halfwidth Note! This page is generated automatically.
using the variable definitions made in the front page file!
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
Issue 2008-09 Doc. No. MM-2864760-0102 Issue 2008-09 Doc. No. MM-2864760-0102
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
EM1.11MM_2864
40 mm Full width Note! This page is generated automatically.
using the variable definitions made in the front page file!
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
HI 020V HI 020V 1(2)

2636960-0200 2636960-0200
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
Issue 2008-09 Doc. No. MM-2864760-0102
Issue 2008-09 Doc. No. MM-2864760-0102
HI 020V HI 020V 2(2)

2636960-0200 2636960-0200
EM1.11MM_2864

MM 2864760 0102

Uploaded by

Copyright:

Available Formats

MM 2864760 0102

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MM 2864760 0102

Uploaded by

Copyright:

Available Formats

MM

Doc. No. MM-2864760-0102

Series No./ Machine No. Sign.

A list of all optional equipment, optional

Doc. No. MM-2864760-0102

Tetra Pak Packaging Solutions

Tetra Pak A3/Flex

Tetra Pak A3/Flex

Date Installed Kit Added Pages Removed Pages Signature

Doc. No. MM-2864760-0102 i - 1 (16)

This chapter contains basic information about this manual

i - 2 (16) Doc. No. MM-2864760-0102

Abbreviations and Terminology . . . . . . . . . . . . . i - 12

How to Use This Maintenance Manual . . . . . . . i - 13

Doc. No. MM-2864760-0102 i - 3 (16)

i - 4 (16) Doc. No. MM-2864760-0102

install the equipment

Doc. No. MM-2864760-0102 i - 5 (16)

3.4 Motor 3 Drive

Doc. No. MM-123457-0108 3 - 15 (102)

i - 6 (16) Doc. No. MM-2864760-0102

4 - 11 (18) 1 Chapter number

The following symbols are used in illustrations:

Doc. No. MM-2864760-0102 i - 7 (16)

i - 8 (16) Doc. No. MM-2864760-0102

Doc. No. MM-2864760-0102 i - 9 (16)

i - 10 (16) Doc. No. MM-2864760-0102

• Do not wear a watch, ring, necklace, earrings, or any other exposed

Steam Barrier in the Product Valve

Doc. No. MM-2864760-0102 i - 11 (16)

Abbreviations and Terminology

i - 12 (16) Doc. No. MM-2864760-0102

How to Use This Maintenance Manual

1.2.3-1 Worm Gear - Change Oil

Doc. No. MM-2864760-0102 i - 13 (16)

Procedure Start Table

1.2.3-1 Worm Gear - Change Oil

1 Air valve OFF

2 Protective gloves TP No. 90303-12

i - 14 (16) Doc. No. MM-2864760-0102

Tetra Pak Maintenance System

Checklists and Spare Parts Recommendations

Doc. No. MM-2864760-0102 i - 15 (16)

i - 16 (16) Doc. No. MM-2864760-0102

Doc. No. MM-2864760-0102 ii - 1 (42)

Safety Precaution Instructions

Definition of Lockout Procedure

ii - 2 (42) Doc. No. MM-2864760-0102

Safety Messages Description. . . . . . . . . . . . . . . ii - 5

Doc. No. MM-2864760-0102 ii - 3 (42)

Equipment for Lifting and Moving Loads . . . . ii - 42

ii - 4 (42) Doc. No. MM-2864760-0102

Safety Messages Description

Danger indicates an imminently hazardous situation

Warning indicates a potentially hazardous situation

Caution indicates a potentially hazardous situation

CAUTION Caution without the safety alert symbol indicates a

potentially hazardous situation which, if not avoided,

Doc. No. MM-2864760-0102 ii - 5 (42)