BRP Series

 Features
 Cylindrical shape structure,ultra-low internal resistance;
 Comply with ROHS standards no Cd Pb and other pollutants;
 Long charge-discharge cycle life;
 Suitable for high power discharge;
 High voltage up to 2.8V, under the same conditions with high reliability.

 Applications

 Working current greater than 100mA, working hours microseconds to a few minutes;
 Can be used for starting device, detonator, the tax control machine, toys, electrical power equipment,etc.

 Standard test conditions

Products are tested under normal pressure, the temperature range is from 5-35 ℃ and relative humidity is less
than RH85% .The standard test conditions in this product specification are as follows: under normal pressure; the
temperature at 25℃ and the relative humidity less than 60%

 Part Number System

BRP Series

 Shape of standard product

Shape of wire lead supercapacitor：

ΦD 5 6.3 8 10 12.5 16 18
Φd 0.5 0.6 0.8
F 2 2.5 3.5 5 7.5 8

L1 28 30 28/30 30

Note: unit mm Shows：ΦD×L=12.5×21,L1=28mm

 BIGCAP®Standard product specification

sheet1
Nominal Capacitance ESR，mΩ Size，mm Weight Volume
Part Number Cap.olerance
Voltage ,V dc F AC@1kHz DC ΦD×L g ml

BRP002R8L104FA 2.8 0.1 0-+40% 450 675 5×12 0.40 0.24

BRP002R8L104FB 2.8 0.1 0-+40% 450 675 5×9.8 0.40 0.19
BRP002R8L154FA 2.8 0.15 ±20% 400 600 5×12 0.40 0.24
BRP002R8L154FB 2.8 0.15 ±20% 450 675 5×9.8 0.40 0.19
BRP002R8L224FA 2.8 0.22 ±20% 500 750 5×12 0.40 0.24
BRP002R8L224FB 2.8 0.22 ±20% 500 750 5×9.8 0.50 0.19
BRP002R8L254FA 2.8 0.25 ±20% 500 750 5×12 0.50 0.24
BRP002R8L254FB 2.8 0.25 ±20% 500 750 6.3×12 0.50 0.37
BRP002R8L354FA 2.8 0.35 ±20% 400 600 5×12 0.60 0.24
BRP002R8L504FA 2.8 0.5 0-+40% 500 750 6.3×12 0.65 0.37
BRP002R8L504FB 2.8 0.5 ±20% 500 750 5×12 0.65 0.24
BRP002R8L504FC 2.8 0.5 ±20% 500 750 6.3×9.8 0.55 0.31
BRP002R8L704FA 2.8 0.7 0-+40% 400 600 8×13 0.85 0.65
BRP002R8L105FA 2.8 1.0 0-+40% 300 450 8×13 0.95 0.65
BRP002R8L105FB 2.8 1.0 0-+40% 200 300 8×19 1.25 0.95
BRP002R8L105FC 2.8 1.0 0-+80% 200 300 8×13 1.05 0.65
BRP002R8L105FD 2.8 1.0 ±20% 300 450 6.3×12 0.70 0.37
BRP002R8L105FE 2.8 1.0 0-+40% 100 150 8×15 1.10 0.75
BRP002R8L105FG 2.8 1.0 0-+80% 80 120 10×20 1.50 1.57
BRP002R8L105FH 2.8 1.0 0-+40% 200 300 8×10 0.85 0.50
BRP002R8L205FA 2.8 2.0 ±20% 140 210 8×19 1.45 0.95
BRP002R8L205FB 2.8 2.0 ±20% 140 210 10×20 1.65 1.57
BRP002R8L305FA 2.8 3.0 0-+40% 100 150 8×19 1.40 0.95
BRP002R8L305FB 2.8 3.0 ±20% 120 180 8×16 1.30 0.80
BRP002R8L335FA 2.8 3.3 ±20% 80 120 10×20 1.90 1.57
BRP002R8L335FB 2.8 3.3 ±20% 100 150 10×16 1.65 1.26
BRP002R8L405FA 2.8 4.0 ±20% 80 120 10×20 2.10 1.57
BRP002R8L475FA 2.8 4.7 ±20% 70 105 12.5×21 3.10 2.58
BRP002R8L475FB 2.8 4.7 ±20% 70 105 10×20 3.10 1.57
BRP002R8L475FC 2.8 4.7 ±20% 70 105 12.5×21 3.20 2.58
BRP002R8L505FA 2.8 5.0 0-+40% 70 105 10×20 2.20 1.57
BRP Series

Nominal Capacitance ESR，mΩ Size，mm Weight Volume

Part Number Cap.olerance
Voltage ,V dc F AC@1kHz DC ΦD×L g ml

BRP002R8L505FB 2.8 5.0 ±20% 70 105 16×26 3.50 5.23

BRP002R8L605FA 2.8 6.0 ±20% 70 105 10×20 2.40 1.57
BRP002R8L705FA 2.8 7.0 ±20% 70 105 10×25 2.70 1.96
BRP002R8L805FA 2.8 8.0 ±20% 50 75 12.5×21 3.50 2.58
BRP002R8L805FC 2.8 8.0 ±20% 50 75 12.5×20 3.40 2.45
BRP002R8L106FA 2.8 10 ±20% 50 75 12.5×26 3.90 3.19
BRP002R8L106FB 2.8 10 ±20% 50 75 12.5×34 4.60 4.17
BRP002R8L106FC 2.8 10 ±20% 60 90 12.5×21 3.30 2.58
BRP002R8L106FD 2.8 10 ±20% 50 75 10×30 3.20 2.36
BRP002R8L126FB 2.8 12 0-+40% 50 75 12.5×26 3.95 3.19
BRP002R8L156FA 2.8 15 ±20% 30 45 16×26 6.00 5.23
BRP002R8L156FB 2.8 15 ±20% 30 45 18×41 7.00 10.43
BRP002R8L166FA 2.8 16 ±20% 30 45 16×21 5.70 4.22
BRP002R8L206FA 2.8 20 ±20% 25 37.5 16×34 7.30 6.83
BRP002R8L226FA 2.8 22 ±20% 25 37.5 16×26 7.00 5.23
BRP002R8L256FA 2.8 25 ±20% 25 37.5 16×34 8.00 6.83
BRP002R8L306FA 2.8 30 ±20% 25 37.5 16×34 8.70 6.83
BRP002R8L306FB 2.8 30 ±20% 25 37.5 18×25 9.00 6.36
BRP002R8L406FA 2.8 40 ±20% 20 30 18×41 13.50 10.43
BRP002R8L506FA 2.8 50 ±20% 20 30 18×41 13.20 10.43
BRP002R8L606FA 2.8 60 ±20% 15 22.5 18×41 14.10 10.43
BRP002R8L706FA 2.8 70 ±20% 15 22.5 18×52 17.20 13.22

sheet2

Energy Density Power Density 72hLC

Max. Stored Nominal Max Leakage

Part Number
Energy，mWh Wh/kg Wh/L KW/kg KW/L Current,A Current,A Current at 72h
Gravimetric Volumetric Gravimetric Volumetric
(25℃) ,uA

BRP002R8L104FA 0.11 0.27 0.46 7.26 12.33 0.06 0.32 ＜1

BRP002R8L104FB 0.11 0.27 0.57 7.26 15.10 0.06 0.32 ＜1

BRP002R8L154FA 0.16 0.41 0.69 8.17 13.87 0.08 0.39 ＜1

BRP002R8L154FB 0.16 0.41 0.85 7.26 15.10 0.08 0.39 ＜1

BRP002R8L224FA 0.24 0.60 1.02 6.53 11.10 0.1 0.5 ＜1

BRP002R8L224FB 0.24 0.48 1.25 5.23 13.59 0.1 0.5 ＜1

BRP002R8L254FA 0.27 0.54 1.16 5.23 11.10 0.1 0.5 ＜1

BRP002R8L254FB 0.27 0.54 0.73 5.23 6.98 0.1 0.5 ＜1

BRP002R8L354FA 0.38 0.64 1.62 5.44 13.87 0.15 0.6 ＜1

BRP002R8L504FA 0.54 0.84 1.45 4.02 6.98 0.17 0.68 ＜2

BRP002R8L504FB 0.54 0.84 2.31 4.02 11.10 0.17 0.68 ＜2

BRP002R8L504FC 0.54 0.99 1.78 4.75 8.55 0.17 0.68 ＜2
BRP002R8L704FA 0.76 0.90 1.17 3.84 5.00 0.18 0.72 ＜2
BRP002R8L105FA 1.09 1.15 1.67 4.58 6.67 0.3 0.92 ＜2
BRP002R8L105FB 1.09 0.87 1.14 5.23 6.84 0.3 0.92 ＜2
BRP Series

72hLC
Energy Density Power Density
Max. Stored Nominal Max Leakage
Part Number
Energy，mWh Wh/kg Wh/L KW/kg KW/L Current,A Current,A Current at 72h
Gravimetric Volumetric Gravimetric Volumetric (25℃) ,uA

BRP002R8L105FC 1.09 1.04 1.67 6.22 10.00 0.45 1.41 ＜2

BRP002R8L105FD 1.09 1.56 2.91 6.22 11.63 0.26 0.81 ＜2
BRP002R8L105FE 1.09 0.99 1.44 11.88 17.34 0.3 0.92 ＜2
BRP002R8L105FG 1.09 0.73 0.69 10.89 10.40 0.45 1.41 ＜2
BRP002R8L105FH 1.09 1.28 2.17 7.69 13.00 0.3 0.92 ＜2
BRP002R8L205FA 2.18 1.50 2.28 6.44 9.78 0.58 2.0 ＜4
BRP002R8L205FB 2.18 1.32 1.39 5.66 5.94 0.58 2.0 ＜4
BRP002R8L305FA 3.27 2.33 3.42 9.33 13.69 0.77 3.19 ＜6
BRP002R8L305FB 3.27 2.51 4.06 8.38 13.55 0.77 3.19 ＜6
BRP002R8L335FA 3.59 1.89 2.29 8.60 10.40 0.77 3.19 ＜7
BRP002R8L335FB 3.59 2.18 2.86 7.92 10.40 0.77 3.19 ＜7
BRP002R8L405FA 4.36 2.07 2.77 7.78 10.40 0.87 4.19 ＜8
BRP002R8L475FA 5.12 1.65 1.99 6.02 7.25 1.26 5.0 ＜10
BRP002R8L475FB 5.12 1.65 3.26 6.02 11.89 1.26 5.0 ＜10
BRP002R8L475FC 5.12 1.60 1.99 5.83 7.25 1.26 5.0 ＜10
BRP002R8L505FA 5.44 2.47 3.47 8.48 11.89 1.26 5.0 ＜10
BRP002R8L505FB 5.44 1.56 1.04 5.33 3.57 1.26 5.0 ＜10
BRP002R8L605FA 6.53 2.72 4.16 7.78 11.89 1.52 5.5 ＜12
BRP002R8L705FA 7.62 2.82 3.88 6.91 9.51 2.06 6.0 ＜14
BRP002R8L805FA 8.71 2.49 3.38 7.47 10.15 2.26 7.0 ＜16
BRP002R8L805FC 8.71 2.56 3.55 7.69 10.65 2.26 7.0 ＜16
BRP002R8L106FA 10.89 2.79 3.41 6.70 8.19 2.45 9.0 ＜20
BRP002R8L106FB 10.89 2.37 2.61 5.68 6.27 2.45 9.0 ＜20
BRP002R8L106FC 10.89 3.30 4.23 6.60 8.45 2.45 9.0 ＜20
BRP002R8L106FD 10.89 3.40 4.62 8.17 11.10 2.45 9.0 ＜20
BRP002R8L126FB 13.07 3.31 4.10 6.62 8.19 2.45 9.0 ＜24
BRP002R8L156FA 16.33 2.72 3.13 7.26 8.33 3.16 9.3 ＜30
BRP002R8L156FB 16.33 2.33 1.57 6.22 4.18 3.16 9.3 ＜30
BRP002R8L166FA 17.42 3.06 4.13 7.64 10.32 3.45 10.2 ＜32
BRP002R8L206FA 21.78 2.98 3.19 7.16 7.65 5.63 16.9 ＜40
BRP002R8L226FA 23.96 3.42 4.58 7.47 10.00 5.63 16.9 ＜44
BRP002R8L256FA 27.22 3.40 3.98 6.53 7.65 5.8 17.6 ＜50
BRP002R8L306FA 32.67 3.75 4.78 6.01 7.65 6.5 18.8 ＜60
BRP002R8L306FB 32.67 3.63 5.14 5.81 8.22 6.5 18.8 ＜60
BRP002R8L406FA 43.56 3.23 4.18 4.84 6.27 10.4 27.0 ＜80
BRP002R8L506FA 54.44 4.12 5.22 4.95 6.27 10.4 27.0 ＜100
BRP002R8L606FA 65.33 4.63 6.27 6.18 8.35 11.6 30.2 ＜120
BRP002R8L706FA 76.22 4.43 5.76 5.06 6.59 13.8 34.5 ＜140
BRP Series

 BIGCAP®Shape of standard product

Shape of snap-in and lead types supercapacitor：

Φ 22.4 25.2 35.6

D
F 10
L1 5.5 6.5
L 45.5 52.5 61.5
Note: unit mm

ΦD 35.6
F 14
L1 2.5
6.5
L 61.5 93

Note: unit mm

 BIGCAP®Standard product specification

sheet3
Nominal Capacitance ESR，mΩ Size，mm Weight Volume
Part Number Cap.olerance
Voltage ,V dc F AC@1kHz DC ΦD×L g ml

BRP002R8S606FA 2.8 60 ±20% 14 16 22.4×45.5 18 17. 92

BRP002R8S107FA 2.8 100 ±20% 12 14 22.4×45.5 21 17. 92
BRP002R8S157FA 2.8 150 ±20% 12 14 25.2×52.5 31 26.17
BRP002R8S207FB 2.8 200 ±20% 10 11 35.6×61.5 48.5 61.19
BRP002R8S307FA 2.8 300 ±20% 8 9 35.6×61.5 60 61.19
BRP002R8S367FB 2.8 360 ±20% 8 9 35.6×61.5 68 61.19
BRP002R8C207FB 2.8 200 ±20% 10 11 35.6×61.5 48.5 61.19
BRP002R8C307FA 2.8 300 ±20% 2.7 3 35.6×61.5 60 61.19
BRP002R8C307FB 2.8 300 ±20% 8 9 35.6×61.5 60 61.19
BRP002R8C367FA 2.8 360 ±20% 2.7 3 35.6×61.5 68 61.19
BRP002R8C367FB 2.8 360 ±20% 8 9 35.6×61.5 68 61.19
BUP002R8C707FA 2.8 700 ±20% 10 12 35.6×93 110 92.53
BRP Series

sheet4

Energy Density Power Density 72hLC

ΔT=15℃
Max. Stored Max Leakage
Part Number Nominal
Energy，mWh Wh/kg Wh/L KW/kg KW/L Current,A Current at 72h
Gravimetric Volumetric Gravimetric Volumetric Current,A
(25℃) ,mA

BRP002R8S606FA 65.33 3.63 3.65 6.81 6.84 6.0 50 ＜0.2

BRP002R8S107FA 108.89 5.19 6.08 6.67 7.81 6.5 65 ＜0.5
BRP002R8S157FA 163.33 5.27 6.24 4.52 5.35 7.7 70 ＜0.8
BRP002R8S207FB 217.78 4.49 3.56 3.67 2.91 8.0 80 ＜1.0
BRP002R8S307FA 326.67 5.44 5.34 3.62 3.56 9.0 85 ＜1.2
BRP002R8S367FB 392.00 5.76 6.41 3.20 3.56 9.4 90 ＜1.4
BRP002R8C207FB 217.78 4.49 3.56 3.67 2.91 8.0 80 ＜1.0
BRP002R8C307FA 326.67 5.44 5.34 10.89 10.68 20 160 ＜1.2
BRP002R8C307FB 326.67 5.44 5.34 3.62 3.56 9.0 85 ＜1.2
BRP002R8C367FA 392.00 5.76 6.41 9.61 10.68 25 180 ＜1.4
BRP002R8C367FB 392.00 5.76 6.41 3.20 3.56 9.4 90 ＜1.4
BUP002R8C707FA 762.22 6.93 8.24 1.48 1.77 11 100 ＜4.0

 Typical characteristics

Product Standard According to IEC 62391-1，GB/T2693—2001，Q/BIG001—2013 test standard

Compared with the initial value, | Δ C/C | ≤ 30%, ESR ≤ 4

Characteristics in Different Temperature －40℃~＋65℃ Initial specified value

Storage Temperature Range (at, 0V) －40℃~＋70℃

Compared with the initial value, |ΔC/C |≤30%, ESR≤2

Humidity Characteristics（at 25℃，90~95%RH） 240h Initial specified value, no leaked electrolyte or other
mechanical damage

Predicted Life at Normal Temperature (at

10years
U0,25℃)

Compared with the initial value, |ΔC/C |≤30%, ESR≤4

High Temperature Life (at U0,65℃) 1000h
Initial specified value, no leaked electrolyte or other
mechanical damage

Cycle Life（at U0 ,25℃） 500000times

Compared with the initial value, |ΔC/C |≤20%, ESR≤3

Shelf Life（at 0V,65℃） 1000h Initial specified value, no leaked electrolyte or other
mechanical damage
BRP Series

Charging process: normal

temperature,non-loaded,charge at rated voltage for 24h
Self discharge characteristics The voltage between the positive and Lay aside process:temperature less than 25℃,relative
(voltage holding characteristics)（at 25℃） negative electrode≥2.1V
humidity less than 60%RH,lay aside 24h at open circuit

 Markings

 Packaging method

Packaging of Wire Lead Supercapacitor：

Suction holder Inner box outside box

Packaging of Snap-in and Lead Types Supercapacitor：

Monomer Inner box outside box

BRP Series

 Characteristic curve

（1）Characteristics in different temperature （2）LC characteristics

（3） High Temperature Life (at 2.8V,65℃）

（4）LC characteristics

*The above characteristic curves are trend charts. Please contact the manufacturer's technical support for the specific data
of each model
BRP Series

 BIGCAP®Measuring Method of BIGCAP

Sheet5
Constant Current Discharge of Measure
1、Set the DC voltage source to the rated voltage (UR)
2、Sets constant current values of a specified constant current discharge device.
3、Switch the switch S to DC power supply , constant voltage charge for 30min after the voltage reachs
to rated voltage.
4、After charging 30min , transform the switch S to constant current discharge device the to discharge
at constant current.
5、Measure the discharge time from U1 to U2 (t1、t2), Calculate capacitance using the following
Capacitance
formula:
Constant current power supply

Equivalent series resistance:

ESR shall be measured from the circuit below ：

Resistance

U
ESR Ra can be calculated from the formula ： R a 
I
Equivalent series resistance（mΩ/Ω）；
U Ac voltage valid values（V r.m.s）；
I Ac current valid values（V r.m.s）。
BRP Series

Sheet6
Leakage Current shall be measured from the circuit below :

Leakage Current 1、Discharge：Before the start of the measurement, supercapacitor should be fully discharge, discharge
process for 1 h to 24 h.
2 、 Leakage current measurement shall be carried out under the rated temperature and voltage rating
（UR）.The voltage of product reached 95% rated voltage after the biggest charging time for 30min，
Charging time chooses from 30min（≤1F），1h（≥1F），2h（≥10F），4h（≥20F），72h（≥
120F).
3、Should use a stable power supply, such as DC regulated power supply.
4、Charge process should be through the protection under 1000Ω resistance.
Before the start of the measurement ，super capacitor should be fully discharge, discharge process for
1 h to 24 h.Charge the super capacitor to rated voltage without protection
Resistance,charging time for 8h(include the voltage of product reached 95% rated voltage after the
biggest charging time for 30min ).Disconnect the super capacitor from the power supply.Super
capacitor should be placed in the standard atmospheric pressure conditions for 24 h. Dc voltmeter
internal resistance should be greater than 1 mΩ.
Self discharge
BRP Series

 Soldering Condition

The recommendation soldering conditions of the product in which flow soldering is possible are as graph。

Caution for Using aluminum Electrolytic Capacitors：

1、 Do not dip the capacitor into melted solder；

2、 Do not flux other part than the terminals；

3、 If there is a direct contact between the sleeve of the capacitor and the printed circuit pattern or

4、 a metal part of another component such as a lead wire, it may cause shrinkage of crack；

5、 If the application is for extended use, understand and manage the soldering characteristics to avoid

6、 abnormal current caused by a contact failure between the capacitor and the PCB；

7、 Please refer to product specifications about other notes。

 Cautions For Use

（1）The problem of using different batches of supercapacitors

When using supercapacitors, we recommend that using the same batch of products, and don’t mix up different batches

of products.

（2）The polarity of super capacitor

Unlike ordinary electrolytic capacitor or battery,the material of positive and negative polarity of super capacitor is same,

so theoretically super capacitor has no polarity; the polarities marked on super capacitor are established by manufacturers in

the production process, when the polarities are used reversely in short-term, it won’t cause substantial damage on capacitor,

and it can be used normally after adjusting to the right polarities. But if reversely use for a long time,the life of super

capacitor will decay quickly.

（3）Super capacitor charging information

To charge a super capacitor requires DC voltage that no more than the rated voltage.It can be charged by a variety of

methods such as current limit, constant current, constant power, constant voltage ; When charging, the super capacitor may
BRP Series

lower the voltage of charging power supply until the capacitor is full to maintain voltage balance.

（4）Internal resistance and capacitance of super capacitor

In the process of charging and discharging, super capacitor’s IR drop caused by inner resistance will leads to lose of

efficiency of capacitor charging and discharging, so the size of capacitor determines the quality of capacitor to some extent;

Due to the internal resistance of the super capacitor is higher than normal capacitors, so in the process of charge and

discharge by AC circuit or high frequency circuit, super capacitor will become heating, and this cause life decay quickly,

that’s why super capacitor only commonly used in DC circuit.

Compared with ordinary capacitor, super capacitor has greater time constant τ , so the charge and discharge time is

longer; also because of this,it is not suitable for working with continuous large current frequently as it can cause performance

decay rapidly. The frequency characteristic of super capacitor is: the response time of positive and negative ions in carbon

electrode pore is longer, so the capacity appears very small. It is not allowed to measure super capacitor by using equipment

for testing common capacitors and AC measuring methods, it should be measured by methods for measuring battery for mAh.

（5）Operating temperature and product

Generally,When BIGCAP® supercapacitors work at rated voltage and low temperatures, the leakage current will be

less ,the standby time and life will be longer . On the contrary, under the condition of rated voltage and higher temperature,

the leakage current increases, the standby time is shortened, and the life is shortened. When the operating temperature is

certain, the life will increase when working at the rated voltage.

（6）Transport and storage

Should prevent products be affected with damp in product transportation,;The storage temperature should be - 30 ℃

to 50 ℃, relative humidity less than 60%, the maximum humidity no more than 85%, otherwise it will cause degradation of

capacitor performance or rust.

（7）Installation and welding

When super capacitors are used for double-sided circuit boards, must pay attention that the joint should not contact
BRP Series

the capacitor, otherwise it will lead to short circuit, over-voltage and damage of capacitor. During the process of installation

and after installation, do not twist or tilted the capacitor, do not be forcibly pull the wires. Capacitors should be welded after

cutting off and bending the leads. In the welding process, pay attention to avoid overheating of the capacitor ( for a 1.6 mm

thickness printed circuit board, the welding temperature should be 260 ℃, time is not more than 5 s), circuit board and the

capacitor should be clean after welding.

Try not to wire

（8）The judgement of short circuit of Super capacitor

When short circuit, the capacitor can not be charged and discharged. Adopt a dc voltage between the positive and

negative electrode of capacitor, if the voltage does not rise,then we can determine short circuit occurs; when using a

multimeter to judge,when charging a new capacitor ,it is a normal phenomenon that ohms shift (short circuit shift) display

short circuit state, at this time, we can not make sure whether the capacitor is short circuit or not, we should observe

whether the resistance value is increased, an increasing on resistance value means no short circuit occurs.

（9）Use in series and parallel

When same super capacitors used in series, the total voltage = capacitor number x capacitor voltage ; The total

capacitance =single capacitor capacitance /capacitor number; Total energy = capacitor number x single capacitor’s

capacitance; total resistance = capacitor number x single capacitor’s resistance.

There is a voltage balance problem when 3 pcs or above capacitors used in series,so an equalization circuit is required

to ensure the capacitor will not over-voltage in long term use process, as over-voltage will cause decay and damage of

capacitor. Different specifications of the super capacitor cannot be used in series.

Super capacitors in different capacitance value can be used in parallel, theses capacitors should be charged by the same

voltage, but should pay attention to the current balance problem between the capacitors and mutual isolation, to avoid

potential difference happened after discharge.

（10）Other problems please consult the manufacturer or refer to BIGCAP® super capacitor relevant technical data.