18-HB13D7-2

INSTALLER'S Library Service Literature

Product Section Unitary

GUIDE Product
Model
Literature Type
Unitary Accessories
Electric, Steam, Hot Water Coils
Installer's Guide
Sequence 39D
ALL phases of this installation must comply with Date February 2008
NATIONAL, STATE AND LOCAL CODES File No. 18-HB13D7-2
Supercedes 18-HB13D7-1

Models:
BAYHTR1405+++
BAYHTR1405BRK
BAYHTR3410000
BAYHTR1415BRK Supplementary
BAYHTR1408+++ BAYHTR3415000
BAYHTR1408BRK
BAYHTR1410+++
BAYHTR1419BRK
BAYHTR1425BRK Electric Heaters
BAYHTR1410BRK
+++ = 000, PDC for Air Handler Installations
IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service information pack upon completion of work.

WARNING: HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING

A. GENERAL
This accessory electric heater is designed to pro- 4. Remove the cover from the heater field wiring
vide power directly to the air handler from the and control compartment box. For heaters up
accessory heaters power supply eliminating the to 15 Kw, an adapter plate is provided which
need for additional circuits. The power and control is used with air handlers that are 21.5” wide
wiring use a single polorized plug to connect the or wider. When required, attach the adapter
heater and the air handler. Single source power plate to the back of the heater on the side
entry is provided for single phase heaters with two opposite the knockouts using 2 screws.
circuits using accessory BAYSPEK140B. See the 5. Remove the appropriate knockouts in the heater
Heater Data table on page 2 for the number of field wiring compartment. See Figure 1 on page 3.
circuits required. Remove the appropriate knockouts in the air han-
1. Check the air handler heater label to comfirm dler for making electrical connections to the heater.
that the selected Heater is approved for use with The holes in the air handler must align with the
this air handler, in the installed configuration. holes in the heater field wiring compartment.
2. Check the components received for damage. 6. Insert the heater assembly into the heater cavity
Report any defects or shortages to the transpor- of the air handler so that the field wiring holes in
tation company immediately. the air handler and the heater will align. Secure
the heater compartment to the air handler with
3. Be sure the power supply agrees with the listing
the four screws removed from the hardware
shown on heater nameplate.
envelope.
B. INSTALLATION
IMPORTANT: Conduit must attach directly to
1. Remove the blower access panel from the front the heater control box.
of the air handler.
NOTE: Air handlers approved to use the 1425 heater
2. Disconnect the female polarized plug from the have a plate covering either the upper or lower 1.2”
wire bundle at left side of air handler near the of the heater cavity. This plate is removed ONLY
knockouts. Discard the male polarized plug and when the 1425 heater is used. Otherwise it must be
power wire leads. left in place for a blower barrier seal.
3. (TWG & TGB models only) Remove the cover 7. Make all wiring connections per applicable field
from the heater compartment of the air handler wiring diagrams in these instructions. All in-
and discard. structions must conform to national, state and
local electrical codes.

© 2008 Trane 02/08

Downloaded from www.Manualslib.com manuals search engine

 INSTALLER'S GUIDE
8. Connect the female polarized plug (disconnected removal of the blower access panel. Remove the
in item 2 from the wire bundle next to the metal cover from the circuit breaker opening in
knockouts) to the male polarized plug on the the air handler access panel and discard, cut out
bottom of the heater control box the fiberglass insulation only in the areas where
9. Refer to the heater minimum airflow chart on the the disconnect will extend through the opening.
air handler rating nameplate for the appropri- 11. Replace all panels removed during the heater
ate minimum blower speed tap to be used with installation.
the approved heater installed.
10. For heaters with self contained disconnect, an
opening in the blower access panel is provided so
that the disconnect may be operated without

BAYHTR -- HEATER DATA

240 VOLT 208 VOLT
Number
Heater Heater Heater
of Phase Capacity Capacity
Model No. Amps per Amps per
Circuits
Circuit Circuit
KW BTUH KW BTUH
BAYHTR1405 +++ 1 1 4.80 16400 20 3.60 12300 17.3
BAYHTR1408 +++ 1 1 7.68 26200 32 5.76 19700 27.7
BAYHTR1410 +++ 1 1 9.60 32800 40 7.20 24600 34.6
BAYHTR3410 000 1 3 9.60 32800 34.6 7.20 24600 30
BAYHTR1415 BRK 2 1 15.36 52400 40/24 11.53 39300 34.6/20.8
BAYHTR3415 000 1 3 15.36 52400 38.2 11.53 39300 33.1
BAYHTR1419 BRK 2 1 19.20 65500 32/48 14.42 49200 27.7/41.6
BAYHTR1425 BRK 3 1 24.96 85200 44/40/20 18.73 63900 38.1/34.6/17.3
+++ = 000, BRK, PDC
000 = pigtails, BRK = contains Circuit Breakers, PDC = contains Pull Disconnect

Page 2 18-HB13D7-2

Downloaded from www.Manualslib.com manuals search engine

 INSTALLER'S GUIDE

1 NOTE 2
SIDE ENTRANCE
TOP ENTRANCE
FOR HEATER ELECTRICAL NOTE 1
FOR HEATER ELECTRICAL
NOTE 1 CONNECTIONS
CONNECTIONS
NOTE 2

CABINET

ADAPTER
PLATE

RESISTANCE HEATER
CONTROL BOX

POLARIZED PLUG

LEADS FROM AIR HANDLER

CONTROL BOX (SEE NOTE 3)

BLOWER ACCESS PANEL

NOTES

1. HEATER LINE VOLTAGE KNOCKOUT LOCATIONS

FOR 1" OR 1-1/2" CONDUIT. CONDUIT MUST BE
ATTACHED DIRECTLY TO THE HEATER CONTROL
BOX. WIRE AND CONDUIT SIZE MUST COMPLY WITH
N.E.C.

2. HEATER LINE VOLTAGE KNOCKOUT LOCATIONS

FOR 3/4" OR 1-1/4" CONDUIT. CONDUIT MUST BE
ATTACHED DIRECTLY TO THE HEATER CONTROL
BOX. WIRE AND CONDUIT SIZE MUST COMPLY WITH
N.E.C.

3. BLOWER CIRCUIT POWER SUPPLY LEADS & LOW

VOLTAGE HEATER CONTROL LEADS FROM AIR
HANDLER CONTROL BOX ARE CONNECTED TO THE
HEATER VIA A POLARIZED PLUG

18-HB13D7-2 Page 3

Downloaded from www.Manualslib.com manuals search engine

 INSTALLER'S GUIDE
MINIMUM HEATING AIRFLOW CFM - HEATER MATRIX
AIR HANDLER MINIMUM HEATING AIRFLOW CFM - HEATER MATRIX

1405 000 1408 000 1410 000

MODEL BRK BRK BRK 1415 BRK 3415 000 1419 BRK 1425 BRK
NUMBER PDC PDC PDC 15.36kw 15.36kw 19.20kw 24.96kw
4.80kw 7.68kw 3410 000
9.60kw

NUMBER OF HEATER RACKS 1 2 2 3 3 4 5

TWG018A L/L L/M L/H -- -- -- --

2TGB3F18 / 2TGB3F25 / TWG025A L/L L/M L/ M L/H L/H -- --

2TGB3F30 / TWG030A L/L L/L L/ L L/M L/M -- --

2TGB3F36 / TWG036/037A L/L L/L L/ L L/M L/M -- --

2TBG3F42 / TWG042A L/L L/L L/ L L/H L/H -- --

TWG048A L/L L/L L/ L L/H L/H L/M --

2TGB3F48 / TWG060A L/L L/L L/ L L/L L/ L L/M L/H

TEC / TWE018C L/L L/M L/M -- -- -- --

TEC / TWE024C L/L L/L L/L L/M L/M -- --

TEC / TWE030C L/L L/L L/L L/M L/M -- --

TEC / TWE036C L/L L/L L/L L/L L /L PS --

TEC / TWEO42C L/L L/L L/L L/H L /H AS --

TWE048C L/L L/L L/L L/L L/L L/H L/H

TEC3F48 L/L L/L L/L L/L L/L L/H

TWE060C/D AS L/L L/L L/L L/L L/H L/H

TEC3F60 L/L L/L L/L L/L L/H

4TEP/TWE018P L/L L/M L/M -- -- -- --

4TEP/TWE024P L/L L/L L/L L/M L/M -- --

4TEP/TWE030P L/L L/L L/L L/M L/M -- --

4TEP/TWE036P L/L L/L L/L L/H L/H L/H --

4TEP/TWEO42P L/L L/L L/L PS PS L/H --

4TEP/TWE048P L/L L/L L/L PS PS L/H L/H

TWE060P L/L L/L L/L PS PS L/H L/H

4TEP/TWE063P L/L L/L L/L PS PS L/H L/H

TEE3D/TEE3F/TWE031E 700/1000 700/1000 700/1000 700/1125 700/1125 1000/1350 --

TEE3D/TEE3F/TWE037E 600/700 600/900 600/900 1000/1300 1000/1300 1000/1350 --

TEE3D/TEE3F/TWE040E 600/1100 600/1100 600/1100 1100/1400 1100/1400 1100/1400 1100/1400

TEE3D/TEE3F/TWE049E 700/1400 700/1400 700/1400 1400/1600 1400/1600 1400/1600 1400/1600

TEE3D/TEE3F/TWE065E 900/1500 900/1500 900/1500 1200/1800 1200/1800 1200/1800 1200/1800

TWE062E* 900/1500 900/1500 900/1500 1200/1800 1200/1800 1200/1800 1200/1800

TEE3C31* 1000/1130 PS/AS 1130/1350 1130/1350 1130/1350 1130/1350 --

TEE3C37* 600/900 900/1100 1100/1450 1100/1450 1100/1450 1100/1450 --

TEE3C40* PS/AS 600/900 900/1100 1100/1400 1100/1400 1100/1400 1100/1400

TEE3C49* 800/1100 800/1100 800/1400 1100/1700 1100/1700 1400/1700 1400/1700

TEE3C65* 900/1200 900/1200 1200/1500 PS/AS PS/AS 1200/1500 1500/1800

COOLING / HEATPUMP AIRFLOW
AS = Heater application is affected based on whether the outdoor unit is a heat pump or cooling unit.
PS = Minimum speed tap varies based on air handler installation position.
SEE AIR HANDLER NAMEPLATE OR PRODUCT DATA FOR AS/PS NOTES
000 = pigtails, BRK = contains circuit breakers, PDC = contains pull disconnect
* These unts require BAYHTR*******C series heaters

Trane Since the manufacturer has a policy of continuous product and product data improvement,
6200 Troup Highway it reserves the right to change design and specification without notice.
Tyler,Tx 75707-9010 Technical Literature - Printed in U.S.A.
Page 4 18-HB13D7-2

Downloaded from www.Manualslib.com manuals search engine