52A-1

GROUP 52A

INTERIOR
CONTENTS

GENERAL DESCRIPTION. . . . . . . . . 52A-3 ON-VEHICLE SERVICE . . . . . . . . . . . 52A-32

PROCEDURES FOR CALIBRATING
SEAT BELT DIAGNOSIS. . . . . . . . . . 52A-4 THE COMPASS . . . . . . . . . . . . . . . . . . . . . 52A-32
INTRODUCTION TO SEAT BELT WARNING SYSTEM PROCESSES FOR ADJUSTING
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . 52A-4 THE COMPASS VARIANCE . . . . . . . . . . . . 52A-33
SEAT BELT WARNING SYSTEM DIAGNOSTIC AUTO-DIMMING FEATURE TEST . . . . . . . 52A-34
TROUBLESHOOTING STRATEGY . . . . . . 52A-4
DIAGNOSIS FUNCTION. . . . . . . . . . . . . . . 52A-4 SPECIAL TOOLS . . . . . . . . . . . . . . . . 52A-35
SYMPTOM CHART. . . . . . . . . . . . . . . . . . . 52A-5
SYMPTOM PROCEDURES . . . . . . . . . . . . 52A-6 INSTRUMENT PANEL ASSEMBLY* . 52A-37
REMOVAL AND INSTALLATION . . . . . . . . 52A-37
COMPASS AND TEMPERATURE DISPLAY DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-39
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . 52A-20
INTRODUCTION TO COMPASS AND FLOOR CONSOLE ASSEMBLY . . . . 52A-40
TEMPERATURE DISPLAY DIAGNOSIS . . 52A-20 REMOVAL AND INSTALLATION . . . . . . . . 52A-40
COMPASS AND TEMPERATURE DISPLAY
DIAGNOSTIC TROUBLESHOOTING TRIMS . . . . . . . . . . . . . . . . . . . . . . . . . 52A-41
STRATEGY. . . . . . . . . . . . . . . . . . . . . . . . . 52A-20
REMOVAL AND INSTALLATION . . . . . . . . 52A-41
SYMPTOM CHART. . . . . . . . . . . . . . . . . . . 52A-20
SYMPTOM PROCEDURES . . . . . . . . . . . . 52A-21
Continued on next page

WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES

WARNING
• Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and
passenger (from rendering the SRS inoperative).
• Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
• MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any
SRS-related component.
NOTE
The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module,
clock spring, and interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection
with SRS service or maintenance) are indicated in the table of contents by an asterisk (*).
52A-2

HEADLINING . . . . . . . . . . . . . . . . . . . 52A-42 DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-50

REMOVAL AND INSTALLATION . . . . . . . . 52A-42
FRONT SEAT BELT . . . . . . . . . . . . . . 52A-52
INSIDE REAR VIEW MIRROR. . . . . . 52A-43 REMOVAL AND INSTALLATION . . . . . . . . 52A-52
REMOVAL SERVICE POINT . . . . . . . . . . . 52A-43 INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . 52A-53

FRONT SEAT ASSEMBLY . . . . . . . . 52A-44 REAR SEAT BELT . . . . . . . . . . . . . . . 52A-54

REMOVAL AND INSTALLATION . . . . . . . . 52A-44 REMOVAL AND INSTALLATION . . . . . . . . 52A-54
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . 52A-45
DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-47 SPECIFICATIONS . . . . . . . . . . . . . . . 52A-55
FASTENER TIGHTENING
REAR SEAT ASSEMBLY . . . . . . . . . 52A-49 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . 52A-55
SERVICE SPECIFICATIONS . . . . . . . . . . . 52A-55
REMOVAL AND INSTALLATION . . . . . . . . 52A-49
 INTERIOR
GENERAL DESCRIPTION
52A-3
GENERAL DESCRIPTION
M1521000100117

OPERATION
.

Inside rear view mirror with compass and

temperature display
.

Seat belt warning system • The compass or temperature will appear on the
• When the ignition switch is turned "ON," the deci- upper right of the mirror when the switch at the
sion circuit operates and the seat belt warning center of the inside rear view mirror is pressed.
light inside of the combination meter flashes four • The compass detects the vehicle direction with
times for 6 seconds. the geomagnetic sensor built in the inside rear
• The decision circuit output makes the seat belt view mirror, and displays eight directions with the
tone alarm sound intermittently for 6 seconds to LCD.
indicate unfastening of the seat belt. • The outside temperature meter calculates the
• When the seat belt is buckled (seat belt buckle information from the outside thermo sensor, and
switch is turned "OFF"), the seat belt tone alarm displays the temperature with the LCD.
stops sounding.
When the ignition switch is turned "OFF," both
seat belt warning light and tone alarm do not
operate.

INSIDE REAR VIEW MIRROR WITH COMPASS AND TEMPERATURE DISPLAY

CONSTRUCTION DIAGRAM

COMPASS DISPLAY TEMPERATURE DISSPLAY

GEOMAGNETIC SENSOR

OUTSIDE THERMO SENSOR

AC003225AC

TSB Revision
52A-4 INTERIOR
SEAT BELT DIAGNOSIS

SEAT BELT DIAGNOSIS

INTRODUCTION TO SEAT BELT WARNING SYSTEM DIAGNOSIS
M1523003700062

The seat belt warning system is controlled by the • The seat belt warning light does not flicker even
ETACS-ECU. when the ignition switch is turned "ON."
The seat belt warning system flashes the seat belt • The seat belt tone alarm does not sound even
warning light in the combination meter for 6 seconds when the ignition switch is turned "ON" while the
after the ignition switch is turned "ON," and sounds a seat belt is not fastened.
seat belt tone alarm if the seat belt is not fastened. • The seat belt tone alarm does not sound even
If one of the following symptoms occurs, a malfunc- when the seat belt is fastened within 6 seconds
tion may have occurred. after the seat belt tone alarm starts sounding.
SEAT BELT WARNING SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1523002700069

Use these steps to plan your diagnostic strategy. If 2. Verify that the condition described by the cus-
you follow them carefully, you will be sure that you tomer exists.
have exhausted most of the possible ways to find a 3. If you cannot verify the condition, the malfunction
fault of the seat belt warning system. is intermittent. Refer to GROUP 00, How to Cope
1. Gather information about the problem from the With Intermittent Malfunctions P.00-7.
customer. 4. Find the malfunction by following the Symptom
Chart.

DIAGNOSIS FUNCTION
M1523002800022

HOW TO CONNECT SCAN TOOL (MUT-III)

Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system) (Vehicles with CAN communi-
cation system)
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-5
1. Ensure that the ignition switch is at the "LOCK" (OFF)
DATA LINK position.
CONNECTOR
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to special tool MB991824.
5. Connect special tool MB991910 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
MB991910
MB991824
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the MUT-III system on the personal computer.
NOTE: Disconnecting the scan tool MB991958 is the
reverse of the connecting sequence, making sure that the
ignition switch is at the "LOCK" (OFF) position.

MB991827 AC305412AB

SYMPTOM CHART
M1523003000096

SYMPTOM INSPECTION REFERENCE

PROCEDURE NO. PAGE
When the seat belt is not fastened and the ignition switch is turned 1 P.52A-6
to the "ON" position, the seat belt tone alarm does not sound and
the seat bet warning light does not illuminate or flash.
When the seat belt is not fastened and the ignition switch is turned 2 P.52A-11
to the "ON" position, the seat belt warning light illuminates or
flashes, but the seat belt tone alarm does not sound.
When the seat belt is not fastened and the ignition switch is turned 3 P.52A-16
to the "ON" position, the seat belt tone alarm sounds, but the seat
belt warning light does not illuminate or flash.
After the ignition switch is turned to the "ON" position, the seat belt Refer to inspection P.52A-11
tone alarm does not stop sounding for 6 seconds, even though the procedure No.2
seat belt is buckled immediately.
NOTE: When no input signals can be checked with the scan tool, there may be a malfunction in the diagnos-
tics circuit system.

TSB Revision
52A-6 INTERIOR
SEAT BELT DIAGNOSIS

SYMPTOM PROCEDURES

INSPECTION PROCEDURE 1: When the Seat Belt is not Fastened and the Ignition Switch is Turned to
the "ON" Position, the Seat Belt Tone Alarm doed not Sound and the Seat Belt Warning Light does not
Illuminate or Flash.

ETACS-ECU Power Supply Circuit

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-7
CONNECTOR: A-54X CONNECTOR: D-01

D-01
A-54X

JUNCTION
AC003431 AC BLOCK (FRONT) AC003227AE

CONNECTORS: D-08, D-11, D-13

D-13
D-08

D-11

JUNCTION
BLOCK (REAR) AC003228AB

TECHNICAL DESCRIPTION (COMMENT)

.

CIRCUIT OPERATION
• The ETACS-ECU powered from fusible link num- The cause may be a malfunction of the ETACS-ECU
ber 6. power supply circuit system or of the ground circuit
• The ETACS-ECU can determine a position of the system.
ignition switch by the ignition switch circuit volt- .

age. TROUBLESHOOTING HINTS

• Malfunction of the ETACS-ECU
• Damaged wiring harnesses or connectors
.

DIAGNOSIS

STEP 1. Measure the power supply line voltage at the

junction block connector D-11
(1) Remove the ETACS-ECU and measure at the junction
block side.
D-11 HARNESS CONNECTOR: (2) Voltage between terminal 2 and ground.
COMPONENT SIDE • The measured value should be approximately 9 volts or
more.
Q: Does the measured voltage correspond with this range?
YES : Go to Step 3.
NO : Go to Step 2.

AC003229 AC

TSB Revision
52A-8 INTERIOR
SEAT BELT DIAGNOSIS

STEP 2. Check the harness wires between fusible link

number 6 and ETACS-ECU connector D-11 (terminal No. 2).
CONNECTOR: D-11

COMPONENT SIDE
D-11

JUNCTION
BLOCK (REAR) AC201084 AB

CONNECTOR: A-54X NOTE: Check the intermediate connectors A-54X, D-01, and
1 2 then the wiring harness. If the intermediate connectors A-54X
and D-01 are damaged, repair or replace them. Refer to
A-54X GROUP 00E, Harness Connector Inspection P.00E-2. Then go
to Step 7.
Q: Are the harness wires between fusible link number 6
and ETACS-ECU connector D-11 (terminal No. 2) in good
condition?
YES : Go to Step 7.
AC200774 AB
NO : Repair it. Then go to Step 7.
CONNECTOR: D-01

D-01

COMPONENT SIDE
5 4 3 2 1
12 11 10 9 8 7 6
JUNCTION
BLOCK (FRONT) AC201083 AB

STEP 3. Measure the ignition switch (IG1) line voltage the

at the junction block connector D-11.
(1) Turn the ignition switch "ON."
(2) Measure the voltage between terminal 3 and the ground.
D-11 • The measured value should be approximately 9 volts or
(JUNCTION BLOCK SIDE) more.
(3) Turn the ignition switch "LOCK" (OFF) position.
Q: Does the measured voltage correspond with this range?
YES : Go to Step 5.
NO : Go to Step 4.

AC003231AB

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-9

STEPS 4. Check the harness wires between ignition switch

(IG1) and ETACS-ECU connector D-11 (terminal No. 3).
CONNECTORS: D-08, D-11

JUNCTION BLOCK (REAR)

D-08 COMPONENT SIDE

2 1
4 3

D-11 COMPONENT SIDE

AC201085 AB

NOTE: Check the intermediate connector D-08, and then the

wiring harness. If the intermediate connector D-08 is damaged,
repair or replace it. Refer to GROUP 00E, Harness Connector
Inspection P.00E-2. If the connector has been repaired or
replaced, go to Step 7.
Q: Is the harness wore between the ignition switch (IG1)
and the ETACS-ECU connector D-11 (terminal No. 3) in
good condition?
YES : Go to Step 7.
NO : Repair them. Then go to Step 7.

STEP 5. Measure the ground line resistance at the junction

block connector D-11.
Check for continuity between terminal 10 and the ground.
D-11 HARNESS CONNECTOR:
COMPONENT SIDE • The measured value should be 2 ohms or less.
Q: Does the measured resistance value correspond with
this range?
YES : Go to step 7.
NO : Go to Step 6.

AC003231AC

TSB Revision
52A-10 INTERIOR
SEAT BELT DIAGNOSIS

STEP 6. Check the harness wires between the ETACS-ECU

connector D-11 (terminal No. 10) and the ground.

9 8 7 6 5 4 3 2 1
2019181716151413121110

AC201086

NOTE: Check the intermediate connector D-13, and then the

wiring harness. If the intermediate connector D-13 is damaged
repair or replace it. Refer to GROUP 00E, Harness Connector
Inspection P.00E-2. Then go to Step 7.
Q: Are the harness wires between the ETACS-ECU
connector D-11 (terminal No.10) and the ground in good
condition?
YES : Go to Step 7.
NO : Repair it. Then go to Step 7.

STEP 7. Retest the system.

Q: Does the seat belt tone alarm sound, or does the seat
belt warning light illuminate or flash?
YES : This procedure is complete. (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points − How to
Cope with Intermittent Malfunction P.00-7.)
NO : There is no action to be taken.

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-11

INSPECTION PROCEDURE 2: When the Seat Belt is not Fastened and the Ignition Switch is Turned to
the "ON" Position, the Seat Belt Warning Light Illuminates or Flashed, but the Seat Belt Tone Alarm
does not Sound.

Seat Belt Switch Circuit

AC004181AB

CONNECTORS: D-11, D-13 CONNECTORS: E-35, E-42

D-13 E-42

E-35
D-11

JUNCTION
BLOCK (REAR) AC003228AC AC003235 AB

• The system flashes the seat belt warning light for

.

CIRCUIT OPERATION
• The system determines whether the seat belt is 6 seconds after the ignition switch is turned "ON,"
fastened by the seat belt switch. and also sounds the seat belt tone alarm if the
seat belt is not fastened.

TSB Revision
52A-12 INTERIOR
SEAT BELT DIAGNOSIS

TROUBLESHOOTING HINTS
.

TECHNICAL DESCRIPTION (COMMENT)

There may be a malfunction in the seat belt buckle • Malfunction of the seat belt buckle switch
switch circuit. • Malfunction of the ETACS-ECU
• Damaged wiring harnesses or connectors
.

DIAGNOSIS
.

Required Special Tols:

• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B (Vehicles without
CAN communication system)
• MB991529: Diagnostic Trouble Code Check Harness
.

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-13

STEP 1. Check the input signal (by using pulse check).

<When using scan tool MB991958>
CAUTION
1. To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
Connect the scan tool MB991958 to the data link connector.
2. If tone alarm of scan tool MB991958 sounds once when the
seat belt buckle switch is operated (ON/OFF), the
ETACS-ECU input signal for that switch circuit system is
normal.
16-PIN
<When using a voltmeter>

MB991911

MB991824

MB991827 AK303629AB

1. Use special tool MB991529 to connect a voltmeter between

the ground terminal 4 or 5 and the ETACS terminal 9 of the
MB991529 data link connector.
2. If the voltmeter indicator deflects once when the seat belt
GROUND buckle switch is operated (ON/OFF), the ETACS-ECU input
TERMINAL
signal for that switch circuit system is normal.
Q: Is the switch circuit system normal?
ETACS YES : Replace the ETACS-ECU P.52A-52. Then go to Step
TERMINAL 5 .
AC003237 AC
NO : Go to Step 2.

STEP 2. Check the seat belt buckle switch continuity.

Q: No continuity should exist when the seat belt is
fastened, while continuity should exist when the seat
TONGUE belt is unfastened?
YES : Go to Step 3.
BUCKLE NO : Replace the seat belt buckle P.52A-52. Then go to
Step 5 .
E-35

AC003238 AE

TSB Revision
52A-14 INTERIOR
SEAT BELT DIAGNOSIS

STEP 3. Check the harness wires between ETACS-ECU

connector D-11 (terminal No. 7) and seat belt buckle switch
connector E-35.
CONNECTORS: D-11, D-13

D-13

D-11

D-11 COMPONENT SIDE

D-13 COMPONENT SIDE

9 8 7 6 5 4 3 2 1
2019181716151413121110

AC201086AD

CONNECTORS: E-35, E-42

E-42

E-35

E-35 COMPONENT SIDE

2 1

E-42
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19

AC203290 AB

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-15
NOTE: Check the intermediate connector D-13 and E-42, and
then the wiring harness. If the intermediate connectors D-13
and E-42 are damaged, repair or replace them. Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Then go
to Step 5.
Q: Is the harness wires between ETACS-ECU connector
D-11 (terminal No. 7) and seat belt buckle switch
connector in good condition?
YES : Go to Step 4.
NO : Repair them. Then go to Step5.

STEP 4. Check the harness wire between seat belt buckle

switch connector E-35 (terminal No.2) and ground.
CONNECTOR: E-35 Q: Is the harness wire between seat belt buckle switch
connector E-35 (terminal No.2) and ground in good
condition?
YES : Go to Step 5.
NO : Repair them. Then go to Step 5.
COMPONENT E-35
SIDE
2 1

AC201073 AB

STEP 5. Retest the system.

Q: The seat belt warning light illuminate or flash, but does
the seat belt tone alarm sound?
YES : This procedure is complete. (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points − How to
Cope with Intermittent Malfunction P.00-7.)
NO : There is no action to be taken.

TSB Revision
52A-16 INTERIOR
SEAT BELT DIAGNOSIS

INSPECTION PROCEDURE 3: When the Seat Belt is not Fastened and the Ignition Switchis Turned to
the "ON" Position, the Seat Belt Tone Alarm Sounds, but the Seat Belt Warning Light does not
Illuminate or Flash.

Seat Belt Warning Light Circuit

CONNECTORS: C-02, C-04 CONNECTORS: D-08, D-11, D-13

C-02 D-13
C-04
D-08

D-11

JUNCTION
AC003241AB BLOCK (REAR) AC003228AB

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-17

CONNECTOR: D-06

D-06

JUNCTION
BLOCK (FRONT) AC003242AC

TECHNICAL DESCRIPTION (COMMENT)

.

CIRCUIT OPERATION There may be a malfunction of the seat belt warning

• The voltage from the ignition switch circuit flashes light circuit or ETACS-ECU.
the seat belt warning light.
• The system flashes the seat belt warning light for .

6 seconds after the ignition switch is turned "ON," TROUBLESHOOTING HINTS

and sounds the seat belt tone alarm if the seat • Malfunction of the seat belt warning light bulb
belt is not fastened. • Malfunction of the ETACS-ECU
• Damaged wiring harnesses or connectors
.

DIAGNOSIS

STEP 1. Check the seat belt warning light circuit line at

junction block connector D-11.
CONNECTOR: D-11 (1) Remove the ETACS-ECU and measure at the junction
block side.
(2) Turn the ignition switch "ON."

COMPONENT SIDE
D-11

JUNCTION
BLOCK (REAR) AC201084 AB

(3) Connect terminal 11 to the ground.

D-11 The system is normal if the seat belt warning light
(JUNCTION BLOCKSIDE) illuminates.
(4) Turn the ignition switch "OFF."
Q: Does the warning light illuminate?
YES : Replace the ETACS-ECU P.52A-52. Then go to Step
4 .
NO : Go to Step 2.

AC003243 AB

STEP 2. Check the seat belt warning light bulb.

Q: Is the seat belt warning light bulb normal?
YES : Go to Step 3.
NO : Replace the seat belt warning light bulb. Then go to
Step 4.

TSB Revision
52A-18 INTERIOR
SEAT BELT DIAGNOSIS

STEP 3. Check the harness wires between the ignition

switch (IG1) and junction block connector D-11(terminal
No 3).
CONNECTORS: D-06, D-08, D-11, D-13

D-06 D-06 COMPONENT SIDE

7 6 5 4 3 2 1
16151413121110 9 8

JUNCTION
BLOCK (FRONT)
D-08 COMPONENT SIDE
D-13
2 1
4 3
D-08

D-11 COMPONENT SIDE

D-11

D-13 COMPONENT SIDE

JUNCTION
BLOCK (REAR) 9 8 7 6 5 4 3 2 1
2019181716151413121110
AC201087AB

CONNECTORS: C-02, C-04 NOTE: Check the intermediate connectors C-02, C-04, D-06,
D-08, D-13, and then their wiring harness. If the intermediate
connectors C-02, C-04, D-06, D-08, D-13 are damaged, repair
C-02 (B) C-04 or replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion P.00E-2. Then go to Step 4.
Q: Is the harness wire between the ignition switch (IG1)
and junction block connector D-11 (terminal No.3) in
good condition?
YES : Go to Step 4.
NO : Repair them. Then go to Step 4.

C-02 COMPONENT SIDE

62 61 60 59 58 57 56 55 54 53 52 51

C-04 COMPONENT SIDE

32 31 30 29 28 27 26 25 24 23 22 21

AC201074 AB

TSB Revision
 INTERIOR
SEAT BELT DIAGNOSIS
52A-19

STEP 4. Retest the system.

Q: The seat belt tone alarm sound, but does the seat belt
warning light illuminate or flash?
YES : This procedure is complete. (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points − How to
Cope with Intermittent Malfunction P.00-7.)
NO : There is no action to be taken.

TSB Revision
52A-20 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

INTRODUCTION TO COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
M1521004200075

If the compass and temperature do not function,

there may be trouble in the electrical system, or the
calibration of the compass may be faulty.

M1524003100267

COMPASS AND TEMPERATURE DISPLAY DIAGNOSTIC TROUBLESHOOTING

STRATEGY

Use these steps to plan your diagnostic strategy. If 2. Verify that the condition described by the cus-
you follow them carefully, you will be sure that you tomer exists.
have exhausted most of the possible ways to find a 3. Find the malfunction by following the Symptom
inside rear view mirror with compass and tempera- Chart.
ture display fault. 4. Verify malfunction is eliminated.
1. Gather information from the customer.
SYMPTOM CHART
M1521003500136

SYMPTOM INSPECTION REFERENCE

PROCEDURE PAGE
NO.
There is no display. 1 P.52A-21
The advance direction is deviated. 2 P.52A-28
The compass cannot be calibrated. 3 P.52A-28
There is a discrepancy between the actual out side temperature and 4 P.52A-29
displayed temperature or an error displays (CS, OS).

TSB Revision
 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-21
SYMPTOM PROCEDURES

INSPECTIN PROCEDURE 1: There is no Display.

Outside Temperature Meter and Electronic Compass Circuit

CONNECTOR: A-22 CONNECTORS: C-01, C-41

C-01
C-41

A-22 (BR)
AC003245AC AC003246AB

TSB Revision
52A-22 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

CONNECTOR: D-06 CONNECTOR: C-72

C-72 (B)
D-06

JUNCTION BLOCK
(FRONT ) AC003227AF AC003247AC

CONNECTOR: E-59 CONNECTOR: D-08

E-59 D-08

JUNCTION BLOCK
AC003248AB (REAR) AC003228AF

CONNECTOR: A-54X
RELAY BOX IN ENGINE COMPARTMENT

A-54X

AC003226AD

. .

CIRCUIT OPERATION TROUBLESHOOTING HINTS

The power is constantly supplied to the inside rear • Malfunction of the inside rear view mirror (with
view mirror (with compass and temperature display). compass and temperature display)
. • Damaged harness or connector
TECHNICAL DESCRIPTION (COMMENT)
The inside rear view mirror (with compass and tem-
perature display), harness, or connector may be
defective.

TSB Revision
 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-23
DIAGNOSIS

STEP 1. Measure the voltage at inside rear view mirror

(with compass and temperature display) power supply
circuit.
CONNECTOR: E-59 (1) Remove the inside rear view mirror (with compass and
temperature display) P.52A-43.
(2) Disconnect the connector.
E-59 (3) Chick at inside rear view mirror (with compass and
temperature display) harness side connector (front side)
E-59.

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

(4) Measure the voltage between terminal number 1 and body

ground.
• Voltage should be 9 volts or more
HARNESS SIDE
CONNECTOR
Q: Does the measured voltage correspond with this range?
(FRONT SIDE) E-59 YES : Go to Step 4.
NO : Go to Step 2.

AC003249 AB

STEP 2. Check harness connector E-59 at the inside rear

view mirror (with compass and temperature display)
connector for damage.
CONNECTOR: E-59 Q: Is harness connector E-59 is good condition?
YES : Go to Step 3.
NO : Repair or replace it. Then go to Step 6.
E-59

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

TSB Revision
52A-24 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

STEP 3. Check the harness wires between the inside rear

view mirror (with compass and temperature display)
connector E-59 (terminal No.1) and ignition switch (ACC).
CONNECTOR: E-59

E-59

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

TSB Revision
 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-25
NOTE: After inspecting intermediate connector C-01 and C-41,
junction block connectors D-06, D-08 and IOD or storage con-
nector A-54X, inspect the wire. If intermediate connector C-01
and C-41, junction block connectors D-06, D-08, and IOD or
storage connector A-54X are damaged, repair or replace them.
Refer to GROUP 00E, Harness Connector Inspection P.00E-2.
CONNECTORS: C-01, C-41
C-01

C-41

C-01

1 2 3 4 5 6 7 8 9 10
111213141516171819202122

C-41
1 2 3 4 5 6 7 8 9 10
111213141516171819202122

AC201076 AB

CONNECTOR: A-54X
RELAY BOX IN ENGINE COMPARTMENT

A-54X

1 2

AC201082 AB

TSB Revision
52A-26 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

CONNECTOR: D-06, D-08 Q: Is the harness wires between inside rear view mirror
(with compass and temperature display) connector E-59
(terminal No.1) and ignition switch (ACC) in good
condition?
YES : Go to Step 6.
D-06 NO : Repair them. Then go to Step 6.
COMPONENT SIDE
7 6 5 4 3 2 1
16151413121110 9 8
JUNCTION BLOCK
(FRONT SIDE)

D-08

COMPONENT SIDE

2 1
4 3

JUNCTION BLOCK
(REAR SIDE) AC201088 AB

STEP 4. Measure the resistance at the inside rear view

mirror (with compass and temperature display) ground
circuit.
CONNECTOR: E-59 (1) Remove the inside rear view mirror (with compass and
temperature display) (Refer to P.52A-43.)
(2) Disconnect the connector.
E-59 (3) Check at inside rear view mirror (with compass and
temperature display) harness side connector (front side)
E-59.

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

(4) Measure the resistance between terminal number 3 and

HARNESS SIDE body ground.
CONNECTOR • Resistance should be 2 ohms or less
(FRONT SIDE) E-59
Q: Does the measured resistance value correspond with
this range?
YES : Go to Step 6.
NO : Go to Step 5.

AC003749 AB

TSB Revision
 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-27

STEP 5. Check the harness wires between inside rear view

mirror (with compass and temperature display) E-59
(terminal No.3) and body ground.
CONNECTOR: E-59

E-59

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

CONNECTOR: C-01 NOTE: After inspecting intermediate connectors C-01, inspect

C-01 the wire. If intermediate connectors C-01 is damaged, repair
the wire. If intermediate connectors C-01 is damaged, repair or
replace it. Refer to GROUP 00E, Harness connector inspection
P.00E-2.
Q: Is the harness wires between inside rear view mirror
(with compass and temperature display) connector E-59
(terminal No.3) and body ground in good condition?
YES : Replace the inside rear view mirror (with compass
and temperature display) (Refer to P.52A-43). Then
go to Step 6.
NO : Repair them. Then go to Step 6.

1 2 3 4 5 6 7 8 9 10
111213141516171819202122

AC201079 AB

STEP 6. Check the symptoms.

Q: Does the outside temperature meter and electronic
compass display values normally?
YES : There is no action to be taken.
NO : This procedure is complete. (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points − How to
Cope with Intermittent Malfunction P.00-7.)

TSB Revision
52A-28 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

INSPECTION PROCEDURE 2: The Advance Direction is Devited.

TECHNICAL DESCRIPTION (COMMENT)

.

CIRCUIT OPERATION
Refer to Outside Temperature Meter and Electronic The vehicle magnetism tends to be disturbed particu-
Compass Circuit (Refer to P.52A-21.) The vehicle larly at such places as tunnel, railway crossing, area
direction is displayed by the output of the geomag- along railway, elevated road, urban area crowded
netic sensor built into the outside temperature meter with high-storied buildings, area above subway, etc.
and electronic compass. If disturbed, the driving direction marker will fluctu-
ate.
.

TROUBLESHOOTING HINTS
The calibration of the compass or compass variance
failed.

DIAGNOSIS
The calibration of the compass or compass variance (Refer to
P.52A-32, P.52A-33.)

INSPECTION PROCEDURE 3: The Compass Cannot be Calibrated.

TECHNICAL DESCRIPTION (COMMENT)

.

CIRCUIT OPERATION
Refer to Outside Temperature Meter and Electronic The inside rear view mirror (with compass and tem-
Compass Circuit (Refer to P.52A-21.) perature display) may be defective.
.

TROUBLE SHOOTING HINTS

.

Malfunction of the inside rear view mirror (with com-

pass and temperature display).

DIAGNOSIS
Check that the calibration of the compass can be carried out at
another place.
1. Move the vehicle to be checked to another place.
NOTE: Move to a wide flat place where calibration of the
compass can be carried out.
2. Check again that calibration of the compass can be carried
out.
NOTE: If the calibration is correct, the following causes can
be assumed.
• Calibration is difficult due to the magnet direction and
direction of the vehicle at the start of calibration.
• There is a disturbing magnetic field in the area, and cali-
bration is difficult.
If the calibration is correct, check that the malfunction is elimi-
nated.
If the calibration is incorrect, replace the inside rear view mirror
(with compass and temperature display) (Refer to P.52A-43.)
Then, check that the malfunction is eliminated.

TSB Revision
 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-29

INSPECTION PROCEDURE 4: There is a Discrepancy Between the Actual Outside Temperature and
Displayed Temperature or an Error Displays (CS, OS).
. .

CIRCUIT OPERATION TECHNICAL DESCRIPTION (COMMENT)

Refer to Outside Temperature Meter and Electronic The outside thermo sensor, inside rear view mirror
Compass Circuit (Refer to P.52A-21.) (with compass and temperature display) harness, or
• A thermistor is used for the thermo sensor. The connector may be defective.
resistance value fluctuate according to ambient .

temperature. The inside rear view mirror (with TROUBLESHOOTING HINTS

compass and temperature display) calculates • Malfunction of the outside thermo sensor
outside temperature according to the changes in • Malfunction of the inside rear view mirror (with
this resistance value, and displays it on the inside compass and temperature display)
rear view mirror (with compass and temperature • Damaged harness or connector
display).

DIAGNOSIS

STEP 1. Check the outside thermo sensor internal

resistance.
(1) Remove the outside thermo sensor P.52A-43.
(2) Check the internal resistance of the outside thermo sensor
THERMOMETER are at the standard values at temperature of 20°C (68°F)
and 40°C (104°F).
Standard value:
Approximately 1,200 Ω [at 20°C (68°F)]
Approximately 500 Ω [at 40 °C (104°F)]
SENSOR Q: Does the out side thermo sensor resistance meet
DRYER standard values above?
YES : Go to Step 3.
AC003251AB
NO : Go to Step 2.

STEP 2. Check harness connector A-22 at the outside

thermo sensor for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
CONNECTOR: A-22
Q: Is harness connector A-22 in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Then go to Step 6.

COMPONENT
SIDE
A-22 (BR)
2 1
AC2019836AB

TSB Revision
52A-30 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS

STEP 3. Measure the outside thermo sensor voltage.

(1) Remove the inside rear view mirror (with compass and
temperature display) (Refer to P.52A-43.)
E-59 HARNESS CONNECTOR: (2) Measure from the rear side of the harness connector E-59
COMPONENT SIDE with the connector connected.
(3) Measure voltage between terminal number 2 and number 7
when the outside thermo sensor is at the following
temperatures.
• Voltage should be approximately 2.90 volts [when 0°C
(32 °F) is displayed]
• Voltage should be approximately 1.86 volts [when 20°C
(68 °F) is displayed]
AC003252 AC • Voltage should be approximately 1.10 volts [when 40°C
(104 °F) is displayed]
Q: Does the voltage between terminal number 2 and
number 7 meet the above values?
YES : Replace the inside rear view mirror (with compass
and temperature display). Then go to Step 6.
NO : Go to Step 4.

STEP 4. Check harness connector E-59 at the inside rear

view mirror (with compass and temperature display)
connector for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
CONNECTOR: E-59 Q: Is harness connector E-59 in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Then go to Step 6.
E-59

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

TSB Revision
 INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-31

STEP 5. Check the harness wires between outside thermo

sensor connector A-22 (terminal No.1 and 2) and inside
rear view mirror (with compass and temperature display)
connector E-59 (terminal No.2 and 7).
CONNECTOR: A-22

COMPONENT
SIDE
A-22 (BR)
2 1
AC2019836AB

CONNECTOR: E-59

E-59

COMPONENT
SIDE
2 1
7 6 5 4 3 AC201078 AB

CONNECTOR: C-01 NOTE: After inspecting intermediate connector C-01, inspect

C-01 the wire. If intermediate connector C-01 is damage, repair or
replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion P.00E-2.
Q: Is the harness wires between outside thermo sensor
connector A-22 (terminal No.1 and 2) and inside rear
view mirror (with compass and temperature display)
connector E-59 (terminal No.2 and 7) in good condition?
YES : Go to Step 6.
NO : Repair them. Then go to Step 6.

1 2 3 4 5 6 7 8 9 10
111213141516171819202122

AC201079 AB

TSB Revision
52A-32 INTERIOR
ON-VEHICLE SERVICE

STEP 6. Retest the system.

Q: Is there any discrepancy between the actual outside
temperature and displayed temperature, or is any error
(CS, OS) displayed?
YES : This procedure is complete. (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points − How to
Cope with Intermittent Malfunction P.00-7.)
NO : There is no action to be taken.

ON-VEHICLE SERVICE
PROCEDURES FOR CALIBRATING THE
COMPASS
M1524011500055
1. Press the "COMP" button. The visual display is now in
compass mode and the vehicle's directional heading (N, NE,
SE, S, SW, W and NW) will be displayed.
Pressing the "COMP" button a second time will turn off the
visual display.

AC003253

2. If the display reads "C," there may be a strong magnetic field

interfering with the compass. In this case, the compass may
need calibration.

AC003254

3. Drive the vehicle in a circle at about 5 mph (8km/h) or less

until the display reads a direction.
You can also calibrate the compass by driving your vehicle
on your everyday routine and after several turns the
compass will become calibrated and will display a direction.

AC003255

TSB Revision
 INTERIOR
ON-VEHICLE SERVICE
52A-33
PROCESSES FOR ADJUSTING THE COMPASS
VARIANCE
M1524012000053
Under certain circumstances, as during a long distance
cross-country trip, it will be necessary to adjust for compass
variance.
Compass variance is the difference between earth's
magnetic north and true geographic north. If not adjusted to
account for compass variance, your compass could give
false readings.
1. Press the "COMP" button for more than 3 seconds. The
current zone number will appear in the display.

AC003256

2. Find your current location and variance zone number on the

map given on the left.
3. Press the "COMP" button until the new zone number
appears in the display.
After you stop pressing the button in, the display will show a
compass direction within a few seconds.
NOTE: Do not install the ski rack, antenna, etc. Which are
attached to the vehicle by means of a magnet. They affect
the operation of the compass.
NOTE: If the compass deviates from the correct indication
soon after repeated adjustment, have the compass checked
at an authorized Mitsubishi dealer.
NOTE: The compass may not indicate the correct compass
point in the places shown below:
• Tunnels
• Areas along he railroad
• Underpass
• Transforming station
• Area with many office buildings
AC003257
• Area over the subway
• Up or down a steep hill
The compass returns to the correct compass point when the
vehicle moves to an area where the geomagnetism in stabi-
lized.

TSB Revision
52A-34 INTERIOR
ON-VEHICLE SERVICE

AUTO-DIMMING FEATURE TEST

M1524012500058
Be sure the ignition is on and that the mirror is on. The green
LED light to the right of the main display switch will be lit
when the mirror is on. If it's not, depress the "TEMP" side of
the main display switch for 15 seconds.
1. Cover the forward-facing light sensor on the back of the
BLACK CLOSE mirror with a black cloth.
2. While in a well-lit area, make sure light strikes the sensor on
the front of the mirror, simulating glare from vehicles behind
you. The mirror will dim within 2 minutes if the testing for the
first time. If the mirror does not dim, replace the inside rear
view mirror.
LIGHT
TEMP SWITCH
SENSOR
AC003258 AB

TSB Revision
 INTERIOR
SPECIAL TOOLS
52A-35
SPECIAL TOOLS
M1521000600338

TOOL TOOL NUMBER AND SUPERSESSION APPLICATION

NAME
MB990784 General service Removal of switch, trim,
Ornament remover tool etc.

MB990784

A MB991958 MB991824-KIT Reading diagnostic

A: MB991824 NOTE: G: trouble code
B: MB991827 MB991826 MUT-III CAUTION
C: MB991910 trigger harness is MUT-III main harness B
D: MB991911 not necessary (MB991911) should be
MB991824
E: MB991914 when pushing used. MUT-III main
B F: MB991825 V.C.I. ENTER key. harness A and C
G: MB991826 should not be used for
MUT-III sub assembly this vehicle.
A: Vehicle communication
interface (V.C.I.)
C
MB991827
B: MUT-III USB cable
C: MUT-III main harness
DO NOT USE A (Vehicles with CAN
communication
system)
MB991910 D: MUT-III main harness
D
B (Vehicles without
CAN communication
system)
E: MUT-III main harness
C (for Daimler Chrysler
MB991911
models only)
E
F: MUT-III measurement
adapter
DO NOT USE
G: MUT-III trigger harness

MB991914

MB991825
G

MB991826
MB991958

TSB Revision
52A-36 INTERIOR
SPECIAL TOOLS

TOOL TOOL NUMBER AND SUPERSESSION APPLICATION

NAME
MB991529 Tool not necessary ETACS-ECU input signal
Diagnostic trouble code if scan tool checking
check harness (MUT-lll) is (When using the
available voltmeter)
MB991529

A MB991223 MB991223 Measurement of

A: MB991223 terminal voltage
Test harness A: Connector pin
B: MB991220 LED contact pressure
harness inspection
B C: MB991221 LED B: Power circuit
harness adapter inspection
D: MB991222 C: Power circuit
Probe inspection
C D: Commercial tester
connection

MB991223AE

TSB Revision
 INTERIOR
INSTRUMENT PANEL ASSEMBLY
52A-37
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATION
M1521001700208

WARNING
For removal and installation of the passenger's side air bag module, always observe the ser-
vice procedures described in GROUP 52B, Air Bag Module and Clock Spring P.52B-84.
The bolts and screws described below are used for installation of the instrument panel. They are indicated by
symbols in the illustration.
NAME SYMBOL SIZE (D × L) mm (in) COLOR SHAPE
Tapping screw A 5 × 12 (0.20 × 0.47) -
B 5 × 14 (0.20 × 0.55)
C 5 × 16 (0.20 × 0.63) ACX01282
D 5 × 20 (0.20 × 0.79)
E 5 × 12 (0.20 × 0.47) Black
F 5 × 16 (0.20 × 0.63)
G 5 × 20 (0.20 × 0.79)
H 5 × 12 (0.20 × 0.47) -
I 5 × 16 (0.20 × 0.63)
ACX01283

Washer assembled screw J 5 × 16 (0.20 × 0.63) -

AC001594

K 5 × 16 (0.20 × 0.63) -
L 5 × 20 (0.20 × 0.79) -
M 5 × 20 (0.20 × 0.79) Black
AC003835

Washer assembled bolt N 6 × 16 (0.24 × 0.63) -

AC003836

O 8 × 20 (0.31 × 0.79) -

AC003837

P 6 × 20 (0.24 × 0.79) -

AC003838

Q 6 × 16 (0.24 × 0.63) -
R 8 × 20 (0.31 × 0.79)
ACX00614

D: Thread diameter
L: Effective thread length

TSB Revision
52A-38 INTERIOR
INSTRUMENT PANEL ASSEMBLY

Pre-removal and Post-installation Operation

• Floor Console Assembly Removal and Installation (Refer
to P.52A-40.)
• Steering Wheel and Column Cover Removal and Installa-
tion (Refer to GROUP 37A, Steering Column and Shaft
P.37A-25.)

19
20 N
19
Q
N

14

15
CC
A

4 J 15
11
J
C
13 Q
17
12 18 A
A M
F 3 C 7
C 8 16
C
G
M
L
10 M M 6
C
M 2 C K 5
E
1
9 AC003259AC
NOTE
: Metal clip position

REMOVAL STEPS REMOVAL STEPS (Continued)

1. HOOD LOCK RELEASE HANDLE 13. HEATER CONTROL ASSEMBLY
2. KNEE PROTECTOR ASSEMBLY (REFER TO GROUP 55, HEATER
3. KNEE PROTECTOR BRACKET CONTROL ASSEMBLY AND A/C
4. METER BEZEL ASSEMBLY SWITCH P.55-35.)
5. UNDER COVER 14. COMBINATION METER
6. CORNER COVER 15. SPEAKER
7. STOPPER 16. GLOVE BOX STRIKER
8. GLOVE BOX ASSEMBLY 17. GLOVE BOX UPPER FRAME
9. ASHTRAY ASSEMBLY 18. FRONT PASSENGER'S SIDE AIR
10. AUDIO PANEL BAG MODULE (REFER TO GROUP
11. RADIO AND TAPE PLAYER AND 52B, AIR BAG MODULES AND
BOX ASSEMBLY CLOCK SPRING P.52B-84.)
12. CENTER UNDER COVER 19. SIDE DEFROSTER GRILL
ASSEMBLY 20. INSTRUMENT PANEL ASSEMBLY

TSB Revision
 INTERIOR
INSTRUMENT PANEL ASSEMBLY
52A-39
DISASSEMBLY AND ASSEMBLY
M1521001900194

6 1
4
H
I B
I H
2 D
D H
8 5 I

7
3

9 10 11 12

P
R P J
P
S P
3 J
15
R J R
13 J
Q

14 AC003260 AC

DISASSEMBLY STEPS DISASSEMBLY STEPS (Continued)

1. DEFROSTER NOZZLE ASSEMBLY 8. INSTRUMENT PANEL
2. DISTRIBUTION DUCT 9. STAY A
3. AIR OUTLET ASSEMBLY 10. STAY B
4. COMBINATION METER 11. STAY C
REINFORCEMENT 12. STAY D
5. INSTRUMENT PANEL 13. GLOVE BOX FRAME
REINFORCEMENT 14. CENTER REINFORCEMENT
6. MULTI-METER BRACKET 15. CENTER FRAME A
7. INSTRUMENT PAD

TSB Revision
52A-40 INTERIOR
FLOOR CONSOLE ASSEMBLY

FLOOR CONSOLE ASSEMBLY

REMOVAL AND INSTALLATION
M1521002200176

3 <RWD> 1 <4WD>

4 <4WD>

5 7

15
14
16 13
11

12

9
6
NOTE 10
: Metal clip position

10 AC003261AB

REMOVAL STEPS REMOVAL STEPS (Continued)

1. SHIFT LEVER KNOB <4WD> 9. REAR HEATER CONTROL PANEL
2. CONSOLE PANEL ASSEMBLY
3. FRONT CONSOLE PANE TRAY 10. FOOT GRILL
<RWD> 11. SWITCH PANEL
4. TRANSFER LEVER BOOT <4WD> 12. OUTER CASE
5. BOX 13. SOCKET
6. REAR FLOOR CONSOLE 14. HEATED SEAT SWITCH
ASSEMBLY <VEHICLES WITH HEATED SEAT>
7. CONSOLE LID ASSEMBLY 15. PLUG
8. KNOB 16. FRONT FLOOR CONSOLE
ASSEMBLY

TSB Revision
 INTERIOR
TRIMS
52A-41
TRIMS
REMOVAL AND INSTALLATION
M1521001100228

9
8
5
4 C
1
C
A
A A
A 44 N·m D A
33 ft-lb
A 11
B
D 10
B
D

D
12

7
3 6
44 N·m
2 33 ft-lb
NOTE 13
: Metal clip position
: Resin clip position
14
SECTION A - A SECTION B - B SECTION C - C SECTION D - D

CLIP
1 CLIP

9, 10
1, 5, 9
CLIP 9

AC003262AB

REMOVAL STEPS REMOVAL STEPS (Continued)

1. FRONT PILLAR TRIM 8. REAR DOOR OPENING
2. COWL SIDE TRIM WEATHERSTRIP, INNER
3. FRONT SCUFF PLATE 9. QUARTER TRIM, UPPER
4. FRONT DOOR OPENING 10. QUARTER TRIM, LOWER
WEATHERSTRIP, INNER 11. PARCEL HOOK
5. CENTER PILLAR TRIM, UPPER 12. REAR END TRIM
6. CENTER PILLAR TRIM, LOWER 13. SHELF HOLDER
7. REAR SCUFF PLATE 14. TONNEAU COVER <VEHICLES
WITH TONNEAU COVER>

TSB Revision
52A-42 INTERIOR
HEADLINING

HEADLINING
REMOVAL AND INSTALLATION
M1521001400207

Pre- removal and Post- installation Operation

² Front Pillar Trim, Center Pillar Trim, Upper and Quarter
Trim, Upper Removal and Installation (Refer to P.52A-41.)

19
18
17

19
16 18
17

10
8 9
7
7

11

2 6
15

9 7 14
8 12 13
5
1
22 N·m
16 ft-lb
3
4

AC202789 AB

HEADLINING REMOVAL STEPS HEADLINING REMOVAL STEPS

1. SUNVISOR ASSEMBLY 9. COAT HANGER
2. SUNVISOR HOLDER 10. HEADLINING TRIM
3. MAP LIGHT ASSEMBLY <VEHICLES 11. HEADLINING
WITH SUNROOF> TETHER ANCHOR REMOVAL
4. OVERHEAD CONSOLE ASSEMBLY STEPS
<VEHICLES WITHOUT SUNROOF> 12. TETHER ANCHOR BRACKET
5. DOME LIGHT ASSEMBLY 13. COVER
6. CARGO ROOM LIGHT ASSEMBLY 14. SPACER 10 mm (0.4 inch)
7. ASSIST GRIP 15. FIVER WASHER
8. GRIP

TSB Revision
 INTERIOR
INSIDE REAR VIEW MIRROR
52A-43
E/A REMOVAL STEPS
• HEADLINING
16. E/A TUBE
17. E/A SIDE ROOF (A)
18. E/A SIDE ROOF (B)
19. E/A SIDE ROOF (C)

INSIDE REAR VIEW MIRROR

REMOVAL SERVICE POINT
M1521002700212
.

<Vehicles without compass and temperature display>

1. Disengage claw A and lower the cover in the arrow 1
3
CLAW A direction.
2 2. Push claw B in the arrow 2 direction to unlock, and pull out
the mirror in the arrow 3 direction.
COVER

CLAW B

AC209066 AC

<Vehicles with compass and temperature display>

1. Disconnect the connector on the inside rear view mirror
side.
2. Remove the cover.
3. Loosen the screw, and remove the inside rear view mirror by
sliding it in the direction of the arrow.

COVER SCREW
AC003264AB

TSB Revision
52A-44 INTERIOR
FRONT SEAT ASSEMBLY

FRONT SEAT ASSEMBLY

REMOVAL AND INSTALLATION
M1522001300195

Pre-removal and Post-installation Operation

• Rear Floor Console Assembly Removal and Installation
(Refer to P.52A-40.)

4 2

44 N·m 44 N·m
33 ft-lb 33 ft-lb

4 3
44 N·m
44 N·m 33 ft-lb
33 ft-lb

4
44 N·m 3
33 ft-lb
AC003265AB

1. HEATED SEAT SWITCH FRONT SEAT ASSEMBLY

<VEHICLES WITH HEATED SEAT> REMOVAL STEPS
(REFER TO P.52A-40.) 3. HARNESS CONNECTORS
2. HEAD RESTRAINT 4. SEAT ANCHOR COVER
>>A<< 5. FRONT SEAT ASSEMBLY

TSB Revision
 INTERIOR
FRONT SEAT ASSEMBLY
52A-45
INSTALLATION SERVICE POINT
.

>>A<< FRONT SEAT ASSEMBLY INSTALLATION

First install all of the front seat assembly mounting nuts and
bolts, and then tighten them to the specified torque.

INSPECTION
M1522005500135
.

CONTINUITY TEST OF HEATED SEAT SWITCH

1. Follow the table below to check between terminals for
continuity.
ITEM SWITCH TESTER SPECIFIED
POSITION CONNECTION CONDITION
Driver's seat HI 1 - 5, 3 - 5, 5 - 8 Less than 2
side ohms
OFF 1 - 3, 1 - 5, 1 - 8, Open circuit
3 - 5, 3 - 8, 5 - 8
AC003266AB
LO 3 - 5, 5 - 8 Less than 2
ohms
Front HI 4 - 5, 5 - 8, 5 - 9 Less than 2
passenger's ohms
seat side
OFF 4 - 5, 4 - 8, 4 - 9, Open circuit
5 - 8, 5 - 9, 8 - 9
LO 5 - 8, 5 - 9 Less than 2
ohms

2. Check that the indicator is lighted at HI or LO when battery

voltage is supplied or the terminal 5 ad the terminal 8 is
ground.
3. Check that the illumination is lighted when battery voltage is
supplied to the terminals 2 and 6.
.

SEAT CUSHION HEATER CHECK

Measure the resistance between terminals.
Standard value:
Between terminals 2 and 3: Approximately 11 Ω
Between terminals 1 and 3: Approximately 9 Ω

AC308661

TSB Revision
52A-46 INTERIOR
FRONT SEAT ASSEMBLY

SEATBACK HEATER CHECK

Measure the resistance between terminals.
Standard value: Approximately 10 Ω

AC308662

TSB Revision
 INTERIOR
FRONT SEAT ASSEMBLY
52A-47
DISASSEMBLY AND ASSEMBLY
M1522001500229

13 16
14
17 15
18

10

9
11 8
12

44 N·m
33 ft-lb

19

3
1
4.9 N·m
43 in-lb
44 N·m 4
33 ft-lb 5
2

6
20
19 24 N·m
17 ft-lb
44 N·m
44 N·m 33 ft-lb 21
33 ft-lb AC003269 AB

DISASSEMBLY STEPS DISASSEMBLY STEPS (Continued)

1. RECLINING ADJUSTER KNOB 6. INNER SEAT BELT
2. SLIDE ADJUSTER KNOB 7. SEAT HEATER HARNESS
3. FRONT SEAT HEIGHT ADJUSTER <VEHICLES WITH HEATED SEAT>
INNER LEVER <VEHICLES WITH 8. FRONT SEAT CUSHION ASSEMBLY
HEIGHT ADJUSTER> 9. FRONT SEAT CUSHION COVER
4. FRONT SEAT HEIGHT ADJUSTER 10. FRONT SEAT CUSHION HEATER
LEVER <VEHICLES WITH HEIGHT <VEHICLES WITH HEATED SEAT>
ADJUSTER> 11. FRONT SEAT CUSHION PAD
5. FRONT SEAT SHIELD COVER 12. FRONT SEAT CUSHION FRAME

TSB Revision
52A-48 INTERIOR
FRONT SEAT ASSEMBLY

DISASSEMBLY STEPS (Continued)

13. FRONT SEATBACK ASSEMBLY
14. HEAD RESTRAINT GUIDE
15. FRONT SEATBACK COVER
16. FRONT SEATBACK HEATER
<VEHICLES WITH HEATED SEAT>
17. FRONT SEATBACK PAD
18. FRONT SEATBACK FRAME
19. RECLINING ADJUSTER
20. SEAT ADJUSTER
21. PULL WIRE

TSB Revision
 INTERIOR
REAR SEAT ASSEMBLY
52A-49
REAR SEAT ASSEMBLY
REMOVAL AND INSTALLATION
M1522001800178

<BENCH SEAT>

8 1
44 N·m
33 ft-lb

44 N·m
33 ft-lb

22 N·m
16 ft-lb

5 6 6
22 N·m 7
16 ft-lb : RESIN CLIP POSITION
<VEHICLES WITH SPLIT SEAT>

1
2
8
8
<SPLIT SEAT> 44 N·m
33 ft-lb
44 N·m
33 ft-lb

DETACHABLE TYPE NON-DETACHABLE TYPE

22 N·m 5 44 N·m
16ft-lb 33 ft-lb
22 N·m
3 22 N·m 16ft-lb
2 16ft-lb
2 5

4 2 AC003270 AB

1. HEAD RESTRAINT REAR SEAT REMOVAL STEPS

REAR SEAT REMOVAL STEPS 6. PARCEL HOOK
2. REAR SEAT CUSHION ASSEMBLY 7. CARGO FLOOR BOX, FRONT
3. STRIKER COVER <VEHICLES WITH SPLIT SEAT>
4. STRIKER ASSEMBLY 8. REAR SEATBACK ASSEMBLY
5. CATCH

TSB Revision
52A-50 INTERIOR
REAR SEAT ASSEMBLY

DISASSEMBLY AND ASSEMBLY

M1522002000205

<BENCH SEAT>

13 9

12 10
11 9
8
7

13

44 N·m
33 ft-lb
15
12

5
18
16 17 14 44 N·m
33 ft-lb

1
2 6
22 N·m
16 ft-lb

12 N·m
104 in-lb 3 AC003271 AB

REAR SEAT CUSHION REAR SEAT BACK

DISASSEMBLY STEPS DISASSEMBLY STEPS
1. HINGE 10. KNOB
2. BAND 11. GARNISH
3. LOCK COVER 12. RECLINING COVER
4. REAR SEAT CUSHION COVER 13. CONTROL CABLE
5. REAR SEAT CUSHION PAD 14. RECLINING ADJUSTER <LH>
6. LOCK BRACKET 15. RECLINING ADJUSTER, OUTER
REAR SEAT BACK <RH>
DISASSEMBLY STEPS 16. REAR SEATBACK COVER
7. PANEL 17. REAR SEATBACK PAD
8. SHELF CLIP 18. REAR SEATBACK FRAME
9. HEAD RESTRAINT GUIDE

TSB Revision
 INTERIOR
REAR SEAT ASSEMBLY
52A-51

<SPLIT SEAT>

12
25 11 13
22 13 N·m
115 in-lb 10
12 15 16 14
18 13
17
18
14
17

11

23 24
44 N·m 19 44 N·m
33 ft-lb 18 33 ft-lb

21
23 25
24 10 20 7
44 N·m
32 ft-lb
<DETACHABLE TYPE> 17 8
7
<NON-DETACHABLE TYPE>
5
8 7 4
22 N·m 9
16 ft-lb
9 8
6
12 N·m
106 in-lb

3 9
2 5
22 N·m 4 5
16 ft-lb 3 6 22 N·m
22 N·m 16 ft-lb 12 N·m
16 ft-lb 106 in-lb
1 6
AC003272AB

REAR SEAT CUSHION REAR SEATBACK

DISASSEMBLY STEPS DISASSEMBLY STEPS
1. BOTTOM COVER 14 GARNISH
2. LEVER ASSEMBLY 15. HINGE BRACKET
3 BRACKET COVER 16. BUSH
4. HINGE 17. RECLINING COVER
5. BAND 18. CONTROL CABLE
6. LOCK COVER 19. RECLINING ADJUSTER <LH>
7. REAR SEAT CUSHION COVER 20. RECLINING ADJUSTER, INNER
8. REAR SEAT CUSHION PAD <LH>
9. LOCK BRACKET 21. RECLINING ADJUSTER, OUTER
REAR SEATBACK <RH>
DISASSEMBLY STEPS 22. ARMREST
10. PANEL 23. REAR SEATBACK COVER
11. SHELF CLIP 24. REAR SEATBACK PAD
12. HEAD RESTRAINT GUIDE 25. REAR SEATBACK FRAME
13. KNOB

TSB Revision
52A-52 INTERIOR
FRONT SEAT BELT

FRONT SEAT BELT

REMOVAL AND INSTALLATION
M1523001300198

5
4
44 N·m
33 ft-lb

44 N·m
2
33 ft-lb

3 7
1

44 N·m
33 ft-lb

44 N·m
33 ft-lb
6 AC103792 AB

1. ETACS-ECU INNER SEAT BELT REMOVAL

OUTER SEAT BELT REMOVAL STEPS
STEPS • FRONT SEAT (REFER TO
• CENTER PILLAR TRIM, LOWER P.52A-44.)
(REFER TO P.52A-41.) 6. INNER SEAT BELT
2. SASH GUIDE COVER 7. FRONT SEAT BELT EXTENSION
3. OUTER SEAT BELT
4. CENTER PILLAR TRIM, UPPER
(REFER TO P.52A-41.)
5. ADJUSTABLE SEAT BELT
ANCHOR

TSB Revision
 INTERIOR
FRONT SEAT BELT
52A-53
INSPECTION
M1523004400138
.

OUTER SEAT BELT CHECK

VIEW A Check that the B section (red) of the label attached to the outer
seat belt is not exposed from the outer seat belt sleeve. If it is
GOOD BAD
exposed, replace the outer seat belt.
B

SLEEVE
A

SLEEVE AC003156AB

SEAT BELT BUCKLE SWITCH CONTINUITY CHECK

Follow the table bellow to check the seat belt buckle switch for
continuity.

ITEM TESTER SPECIFIED

CONNECTION CONDITION
Fastened seat belt 1−2 Open circuit
Unfastened seat belt 1 − 2 Less than 2 ohms

AC308036

TSB Revision
52A-54 INTERIOR
REAR SEAT BELT

REAR SEAT BELT

REMOVAL AND INSTALLATION
M1523001600207

6
44 N·m
33 ft-lb

44 N·m
33 ft-lb
4

2
2
1
AC103793 AB

1. CENTER SEAT BELT OUTER SEAT BELT REMOVAL

2. INNER SEAT BELT STEPS
3. EXTENDER SEAT BELT 4. QUARTER TRIM, LOWER (REFER
ASSEMBLY TO P.52A-41.)
5. QUARTER TRIM, UPPER (REFER
TO P.52A-41.)
6. OUTER SEAT BELT

TSB Revision
 INTERIOR
SPECIFICATIONS
52A-55
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1521004100120

ITEM SPECIFICATION
Adjustable seat belt anchor bolt 44 N⋅m (33 ft-lb)
Front inner seat belt bolt 44 N⋅m (33 ft-lb)
Front outer seat belt bolt 44 N⋅m (33 ft-lb)
Front seat adjuster bolt 24 N⋅m (17 ft-lb)
Front seat bolt 44 N⋅m (33 ft-lb)
Front seat height adjuster lever bolt 4.9 N⋅m (43 in-lb)
Front seat reclining adjuster bolt 44 N⋅m (33 ft-lb)
Rear center seat belt bolt 44 N⋅m (33 ft-lb)
Rear inner seat belt bolt 44 N⋅m (33 ft-lb)
Rear outer seat belt bolt 44 N⋅m (33 ft-lb)
Rear seat band bolt 12 N⋅m (104 in-lb)
Rear seat catch bolt 22 N⋅m (16 ft-lb)
Rear seat cushion assembly bolt 22 N⋅m (16 ft-lb)
Rear seat hinge bolt 22 N⋅m (16 ft-lb)
Rear seat hinge bracket bolt 13 N⋅m (115 in-lb)
Rear seat lever assembly bolt 22 N⋅m (16 ft-lb)
Rear seat lock bracket screw 12 N⋅m (104 in-lb)
Rear seat reclining adjuster bolt 44 N⋅m (33 ft-lb)
Rear seatback assembly bolt 44 N⋅m (33 ft-lb)
Striker assembly 22 N⋅m (16 ft-lb)
Tether anchor bracket bolt 22 N⋅m (16 ft-lb)

SERVICE SPECIFICATIONS
M1522000300062

ITEM STANDARD VALUE

Seat cushion Ω Between terminals 2 and 3 Approximately 11
Between terminals 1 and 3 Approximately 9
Seatback Ω Between terminals 1 and 2 Approximately 10

TSB Revision
NOTES