Scribd Logo
Upload

Welcome to Scribd!

  • 28 views

    Asme Wps

    Uploaded by

    Dilip Patil
    The document provides specifications for a welding procedure including details about the base metals, filler metals, positions, preheat and postweld heat treatment requirements, gas and electrical characteristics, and welding technique.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Asme Wps

    Uploaded by

    Dilip Patil
    28 views2 pages
    The document provides specifications for a welding procedure including details about the base metals, filler metals, positions, preheat and postweld heat treatment requirements, gas and electrical characteristics, and welding technique.

    Original Title

    asme_wps

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides specifications for a welding procedure including details about the base metals, filler metals, positions, preheat and postweld heat treatment requirements, gas and electrical characteristics, and welding technique.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    28 views2 pages

    Asme Wps

    Uploaded by

    Dilip Patil
    The document provides specifications for a welding procedure including details about the base metals, filler metals, positions, preheat and postweld heat treatment requirements, gas and electrical characteristics, and welding technique.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 2

    Backing

    WELDING PROCEDURE SPECIFICATION (WPS) Welding Engineering


    acc. to QW-200.1, Section IX, ASME Boiler and Pressure Vessel Code Department

    THIS FORM FOLLOW THE GENERAL FORM ASME SECTION IX QW-482 FOR WELDING PROCEDURE SPECIFICATION (WPS)
    WPS No.: Date: Rev. No: Date: Page 1 of 2
    Supporting PQR-No.(s):
    Joints (QW-402) Joint details inclusive of welding process No.(s) and base metal part No.(s)

    Base Metals (QW-403)


    Joint design
    Backing Base metal to Base metal Dimension
    material type
    P-No. A:
    (Referand Group No.
    to both
    backing and type and grade
    Specification B:
    retainers) C: Fillet
    Dimensions Ranges: Groove Fillet Groove
    Thickness or diameter with impacts [mm] D:
    Thickness or diameter without impacts [mm] E:
    Pipe or tube diameter [mm] F:
    Width of ligament between tube holes [mm] G:
    Filler Metals (QW-404) H:
    I:
    Process No. (see above QW-402)
    J:
    Filler metal
    Solid / tubular / metal-cored
    Filler metal F-No.
    Weld metal analysis A-No.
    SFA Specification No.
    AWS Classification No.
    Filler metal manufacturer
    Filler metal trade name
    Size of filler metal [mm]
    Filler metal size first layer [mm]
    Flux or covering type
    Consumable insert
    Supplementary filler metal
    Supple. powdered filler metal
    Thicknes Groove [mm]
    s range of pro-
    cess Fillet
    Each [mm]
    With impacts Groove [mm]: - Fillet [mm]:
    Total Without impacts Groove [mm]: - Fillet [mm]:
    Other restrictions
    if applicable

    Positions (QW-405)
    Position(s) of Groove Welding Progression Position(s) of Fillet

    Other:

    Person in charge: Welding Engineer:


    WELDING PROCEDURE SPECIFICATION (WPS) Welding Engineering
    acc. to QW-200.1, Section IX, ASME Boiler and Pressure Vessel Code Department

    THIS FORM FOLLOW THE GENERAL FORM ASME SECTION IX QW-482 FOR WELDING PROCEDURE SPECIFICATION (WPS)
    WPS No.: Date: Rev. No: Date: Page 2 of 2
    Preheat (QW-406) Minimum temperature for welding
    Remark Preheat temp. min. Interpass temp. max. Preheat maintenance
    (e.g. layer, process) [C] [C]

    Other:

    Postweld Heat Treatment (QW-407)


    Heat treatment Heating rate max. Holding temp. Holding time Cooling down: Residual cooling
    [C/h] [C] [min] at max. rate [C/h] at least to [C] down
    + -
    Gas (QW 408) Percent Composition [%] Flow
    rate
    Performance Remark Gas(es) Ar He CO2 O2 N2 H2 [ l/min ]

    Other:

    Electrical Characteristics (QW-409)


    Welding process Filler Metal Current Ranges of electrical characteristics
    No.(s) Desig- Con- AWS Class. Size AC Type Ampe- Voltage Travel Arcing Run-out Weaving Wire feed
    (see nation tact No. or polarit rage speed time length width speed
    QW-402 tube [mm] DC y [A] [V] [cm/min] [sec] [cm] [mm] [m/min]
    above

    Tungsten electrode diameter [mm]:


    Tungsten electrode type:
    Mode of metal transfer for GMAW:
    Power source (type):
    Other:
    Technique (QW-410)
    Process No. ( see above QW-402 )
    Welding process designation
    Welding process type
    String or weave bead
    Orifice or gas cup size [mm]
    Contact tube to work distance [mm]
    Multiple or single electrodes
    Electrode spacing [mm]
    Welding in closed chamber
    Stud lift [mm]
    Stud gun model
    Multiple or single pass (per side)
    Cleaning Initial
    Interpass
    Surfaces of the test coupons to be welded shall be clean and free of scale, rust, oil, grease and other deliterious foreign material; for
    a distance of at least 1/2" (13 mm) from the welding joint preparation for ferrous materials, and at least 2"
    (50 mm) for nonferrous materials.
    Method of back gouging
    Oscillation and travel speed See above table Electrical Characteristics (QW-409).
    Peening

    Person in charge: Welding Engineer:

    You might also like