Catalogue Master 7
Catalogue Master 7
Catalogue Master 7
MANUALE D’USO
USER'S MANUAL
MODE D’EMPLOI
BETRIEBSANLEITUNG
MANUAL DE USO
L.C. snc Via I° Maggio 25010 Isorella - BS - Italy Tel. 030 9529040 Fax 030 9529638
ENGLISH
TABLE OF CONTENTS: THE FOLLOWING MESSAGE IS DISPLAYED: NUMBER OF
PAGE 1 : TARE RESET ANIMALS. SET THE CHOSEN ANIMAL NUMBER BY MEANS OF
PAGE 1 : SETTING THE LOADING PROCEDURE THE KEYS 5 e6 , i.e. 100 AND CONFIRM BY PRESSING OK.
PAGE 2 : SETTING THE UNLOADING PROCEDURE THE WEIGHING EQUIPMENT STORES THE DATA AND DISPLAYS
PAGE 3 : LOADING C1:0.0. SET THE WEIGHT OF THE FIRST COMPONENT BY
PAGE 4 : UNLOADING MEANS OF THE KEYS 5 e6 , i.e. 3,5 Kg.
PAGE 4 : WEIGHT LOCKING PRESS OK TO SAVE THE DATA AND THE PRESS WILL
PAGE 4 : RESTORING THE SET WEIGHT AUTOMATICALLY MOVE TO THE SECOND COMPONENT: C2:0.0
PAGE 5 : WEIGHT CALIBRATION SET THE WEIGHT OF THE SECOND COMPONENT BY MEANS OF
PAGE 5 :SETTING THE PARAMETERS THE KEYS 5 e6 , i.e. 5,0 Kg.
PRESS OK TO SAVE THE DATA AND THE PRESS WILL
AUTOMATICALLY MOVE TO THE THIRD COMPONENT: C3:0.0
WEIGHING EQUIPMENT ON : T 0 SET THE WEIGHT OF THE THIRD COMPONENT BY MEANS OF
TARE RESET: HOLD THE KEY 6 PRESSED FOR 5 THE KEYS 5 e6 , i.e. 16,0 Kg.
SECONDS. PRESS OK TO SAVE THE DATA AND THE PRESS WILL
WHEN THE DASHES ARE DISPLAYED ----- RELEASE AUTOMATICALLY MOVE TO THE FOURTH COMPONENT: C4:0.0.
THE KEY. THERE ARE UP TO 12 COMPONENTS TO BE LOADED.
THE WEIGHING EQUIPMENT HAS BEEN RESET: AFTER SETTING THE LAST COMPONENT, N12, PRESS OK AND
Tot 0 THE WEIGHING EQUIPMENT WILL DISPLAY THE RATION PER
PRESS THE MENU KEY: SETTING THE LOADING ANIMAL: RA:024.5 .
PROCEDURE SETTING THE UNLOADING PRESS OK AND THE WEIGHING EQUIPMENT WILL DISPLAY
PROCEDURE LOADING UNLOADING THE TOTAL WEIGHT TO BE LOADED: T2450
CONFIRM THE CHOSEN OPTION BY PRESSING OK, PRESS OK AND THE WEIGHING EQUIPMENT GOES BACK TO
i.e. SETTING THE LOADING PROCEDURE TOTAL WEIGHT MODE: Tot 0.
SETTING THE LOADING PROCEDURE:
THE FOLLOWING MESSAGE IS DISPLAYED Note: YOU CAN QUIT THE PROGRAMMING WINDOW AT ANY TIME
LOADING PROCEDURE RECIPE N1. SET THE BY HOLDING THE MENU KEY PRESSED FOR ABOUT 5 SECONDS.
CHOSEN RECIPE NUMBER BY MEANS OF THE
KEYS 5 e6 , i.e. REC 2.
PRESS OK TO START PROGRAMMING THE
LOADING PROCEDURE FOR THE RECIPE N2.
1
ENGLISH
SETTING THE UNLOADING PROCEDURE:
Note: THE UNLOADING PROCEDURE SHALL BE SET ACCORDING TO THE NUMBER OF ANIMALS TO BE FED.
Ex: IF THE PROGRAMMED RECIPE IS LOADED FOR 100 ANIMALS DIVIDED INTO 2 PENS (1st PEN =40 Animals. 2nd PEN=60
Animals)THE UNLOADING PROCEDURE SHALL BE SET AS FOLLOWS:
HOLD THE MENU KEY PRESSED TILL THE EQUIPMENT DISPLAYS THE MESSAGE UNLOADING PROCEDURE AND
CONFIRM BY PRESSING OK.
THEN THE MESSAGE REC 1 WILL APPEAR. SET THE CHOSEN RECIPE NUMBER BY
MEANS OF THE KEYS 5e6 , i.e. REC 2.
PRESS OK TO START PROGRAMMING THE UNLOADING PROCEDURE FOR THE RECIPE N2.
THE WEIGHING EQUIPMENT WILL DISPLAY THE FOLLOWING MESSAGE: RECIPE N2 UNLOADING N1 0
BY MEANS OF THE ARROW KEY 5e6 SET THE NUMBER OF ANIMALS FOR THE FIRST UNLOADING OPERATION, i.e. 40,
AND CONFIRM BY PRESSING OK.
THE WEIGHING EQUIPMENT WILL NOW DISPLAY THE FOLLOWING MESSAGE RECIPE N2 UNLOADING N2 0
BY MEANS OF THE ARROW KEY 5e6 SET THE NUMBER OF ANIMALS FOR THE SECOND UNLOADING OPERATION, i.e.
60, AND CONFIRM BY PRESSING OK.
CHECK THAT THE VALUES FOR THE REMAINING UNLOADING OPERATIONS ARE SET AT ZERO BY PRESSING OK.
AFTER HAVING CHECKED THE SIXTH UNLOADING OPERATION THE WEIGHING EQUIPMENT GOES BACK TO TOTAL
WEIGHT MODE.
WITH THE PROCEDURE ABOVE WE HAVE SET A FIRST UNLOADING EQUAL TO 980 Kg. ( 40 Animals X 24.5 Kg. ration ) AND
THE SECOND UNLOADING EQUAL TO 1470 Kg. ( 60 Animals X 24.5 Kg. ration )
Note: YOU CAN QUIT THE PROGRAMMING WINDOW AT ANY TIME BY HOLDING THE MENU KEY PRESSED FOR ABOUT 2
SECONDS.
2
ENGLISH
LOADING :
Ex: WE WILL NOW RUN THE RECIPE N2 THAT WE HAVE JUST SET.
LOADING OPERATION:
PRESS 4 TIMES THE MENU KEY TO DISPLAY THE MESSAGE LOADING AND CONFIRM BY PRESSING OK.
THEN THE MESSAGE LOADING RECIPE N1 WILL APPEAR. SET THE CHOSEN RECIPE NUMBER BY MEANS OF THE
KEYS 5e6 , i.e. REC 2.
PRESS OK TO START LOADING THE RECIPE N2.
THE WEIGHING EQUIPMENT WILL DISPLAY THE FOLLOWING VALUE C1: 350 Kg. THAT IS THE TOTAL WEIGHT OF THE
FIRST COMPONENT TO BE LOADED.
THE WEIGHING EQUIPMENT JUST MULTIPLIED THE NUMBER OF ANIMALS 100 BY THE WEIGHT OF THE FIRST
COMPONENT ( C1:3.5 ).
WHEN YOU START LOADING THE COMPONENT YOU WILL SEE THE DISPLAYED VALUE DECREASE.
WHEN THE EQUIPMENT REACHES THE 85% OF THE PROGRAMMED WEIGHT AN ACOUSTIC SIGNAL (SIREN) STARTS
RINGING INTERMITTENTLY. UPON COMPLETION OF THE LOADING OPERATION - 100% OF THE SET WEIGHT LOADED
THE SIREN WILL RING FOR 7 SECONDS THUS SIGNALLING THAT THE LOADING OF THE FIRST COMPONENT HAS
BEEN COMPLETED.
THE WEIGHING EQUIPMENT WILL THEN AUTOMATICALLY MOVE TO THE SECOND COMPONENT C2 : 500 Kg.
WHEN YOU START LOADING THE COMPONENT YOU WILL SEE THE DISPLAYED VALUE DECREASE.
WHEN THE EQUIPMENT REACHES THE 85% OF THE PROGRAMMED WEIGHT AN ACOUSTIC SIGNAL (SIREN) STARTS
RINGING INTERMITTENTLY. UPON COMPLETION OF THE LOADING OPERATION - 100% OF THE SET WEIGHT LOADED
THE SIREN WILL RING FOR 7 SECONDS THUS SIGNALLING THAT THE LOADING OF THE SECOND COMPONENT HAS
BEEN COMPLETED.
THE WEIGHING EQUIPMENT WILL THEN AUTOMATICALLY MOVE TO THE THIRD COMPONENT C3 : 1600 Kg.
UPON COMPLETION OF THE LOADING OF THIS LAST COMPONENT THE WEIGHING EQUIPMENT DISPLAYS THE TOTAL
WEIGHT LOADED:
TOTAL WEIGHT - 2450 Kg.
Note: YOU CAN QUIT THE LOADING WINDOW AT ANY TIME BY HOLDING THE MENU KEY PRESSED FOR ABOUT 5
SECONDS.
3
ENGLISH
UNLOADING:
MANUAL UNLOADING : WHEN UNLOADING THE RECIPE FROM THE EQUIPMENT THE WEIGHT DECREASES TO ZERO.
PROGRAMMED UNLOADING: PRESS 4 TIMES THE MENU KEY TO DISPLAY THE OPTION UNLOADING AND CONFIRM
BY PRESSING OK.
THEN THE MESSAGE UNLOADING RECIPE N1 WILL APPEAR. SET THE CHOSEN RECIPE NUMBER BY MEANS OF THE
KEYS5e6 , i.e. REC 2.
PRESS OK TO START UNLOADING THE RECIPE N2. THE WEIGHING EQUIPMENT WILL DISPLAY THE FOLLOWING
MESSAGE: RECIPE N2 UNLOADING N1 980 Kg. THAT IS A VALUE GIVEN BY THE NUMBER OF ANIMALS IN THE
FIRST PEN ( S1:40 ) TIMED BY THE RATION PER ANIMAL ( 2450 : 100 = 24.5 Kg. ) IN FACT 40 x 24.5 = 980.
WHEN YOU START UNLOADING THE RECIPE YOU WILL SEE THE DISPLAYED VALUE DECREASE. WHEN THE
EQUIPMENT REACHES THE 85% OF THE PROGRAMMED WEIGHT AN ACOUSTIC SIGNAL (SIREN) STARTS RINGING
INTERMITTENTLY. UPON COMPLETION OF THE UNLOADING OPERATION - 100% OF THE SET WEIGHT UNLOADED
THE SIREN WILL RING FOR 7 SECONDS THUS SIGNALLING THAT THE UNLOADING FOR THE FIRST PEN HAS BEEN
COMPLETED.
THE WEIGHING EQUIPMENT WILL THEN AUTOMATICALLY MOVE TO THE SECOND UNLOADING : RECIPE N2
UNLOADING N2 1470 Kg.
WHEN YOU START UNLOADING THE RECIPE YOU WILL SEE THE DISPLAYED VALUE DECREASE. WHEN THE
EQUIPMENT REACHES THE 85% OF THE PROGRAMMED WEIGHT AN ACOUSTIC SIGNAL (SIREN) STARTS RINGING
INTERMITTENTLY. UPON COMPLETION OF THE UNLOADING OPERATION - 100% OF THE SET WEIGHT UNLOADED
THE SIREN WILL RING FOR 7 SECONDS THUS SIGNALLING THAT THE UNLOADING FOR THE SECOND PEN HAS BEEN
COMPLETED.
UPON COMPLETION OF THE UNLOADING OPERATIONS THE WEIGHING EQUIPMENT GOES BACK TO TOTAL WEIGHT
MODE: Tot 0.
Note: YOU CAN QUIT THE UNLOADING WINDOW AT ANY TIME BY HOLDING THE MENU KEY PRESSED FOR ABOUT 5
SECONDS.
WEIGHT LOCKING:
WHEN HANDLING THE EQUIPMENT YU CAN LOCK THE WEIGHT BY PRESSING BLOCK.
PRESS SBLOCK TO UNLOCK THE SYSTEM.
RESTORING THE SET WEIGHT:
IF DURING A LOADING OPERATION THE SET WEIGHT FOR A COMPONENT CHANGES (i.e. 500 Kg. SET 495 Kg. DISPLAYED) YOU
CAN RECALL THE ORIGINAL WEIGHT BY HOLDING THE BLOCK/SBLOCK KEY PRESSED FOR ABOUT 5 SECONDS.
4
ENGLISH
WEIGHT CALIBRATION:
RESET THE TARE BY KEEPING THE KEY6 PRESSED FOR ABOUT 5 SECONDS.-------
LOAD A FIXED WEIGHT, FOR EXAMPLE 500 Kg.
IF THE WEIGHT DISPLAYED IS NOT CORRECT, I.E. THE EQUIPMENT DISPLAYS: TOTAL WEIGHT 470 Kg., KEEP THE
OK KEY PRESSED FOR AROUND 5 SECONDS AND THEN PRESS THE 5 KEY.
RELEASE THE KEYS, THE WEIGHING EQUIPMENT WILL DISPLAY THE FOLLOWING MESSAGE: MOD. 470 Kg.
SET THE CORRECT WEIGHT OF 500 Kg. BY MEANS OF THE KEYS5e6 , THEN CONFIRM BY PRESSING OK.
WITH THE SCALE SWITCHED OFF, KEEP THE KEYS5e6 PRESSED. SWITCH THE SCALE ON BY PRESSING ON/OFF.
RELEASE ALL THE KEYS AND WAIT FOR A FEW SECONDS.
THE SCALE WILL DISPLAY THE MESSAGE CAPACITY 16000. PRESS OK TO CONFIRM AND MOVE TO THE FOLLOWING
PARAMETER.
DIVISION 2: USE THE KEYS 5e6 TO SET THE CHOSEN READING DIVISION ( 1-2-5-10 )
PRESS OK TO CONFIRM AND MOVE TO THE FOLLOWING PARAMETER.
SPEED 4: USE THE KEYS 5e6 TO SET THE CHOSEN READING SPED ( 1-2-3-4-5-6 )
1=HIGH 6=LOW. PRESS OK TO CONFIRM AND MOVE TO THE FOLLOWING PARAMETER.
LANGUAGE : IT=ITALIAN GB=ENGLISH FR=FRENCH DE=GERMAN ES=SPANISH PORT=PORTOGUESE. POL=Polish
NL=Dutch RUM=Romanian PRESS OK TO CONFIRM AND MOVE TO THE FOLLOWING PARAMETER.
SAMPLE WEIGHT 14600 SET THE VALUE THAT YOU WANT TO USE TO CALIBRATE THE SCALE, e.g. 300 Kg. PRESS OK
TO CONFIRM
UNLOADING - CHECK THAT THE SCALE IS EMPTY AND PRESS OK
LOADING - LOAD THE SCALE WITH THE SAMPLE WEIGHT - 300 Kg AND PRESS OK.
UNLOADING - UNLOAD THE SAMPLE WEIGHT - 300 Kg FROM THE SCALE AND PRESS OK.
END - PRESS OK TO EXIT PROGRAMMING.
Note: YOU CAN QUIT PROGRAMMING AT ANY TIME BY KEEPING THE MENU KEY PRESSED FOR A FEW SECONDS.
5
DICHIARAZIONE DI CONFORMITA':
LA DITTA
L.C. s.n.c. di Trombini Luca & C.
Via I Maggio
25010 Isorella - BS -
DICHIARA CHE:
GARANZIA:
LA DITTA L.C. s.n.c. di Trombini Luca & C. GARANTISCE I PROPRI PRODOTTI PER 24 MESI
DALLA DATA DI ACQUISTO.
LA GARANZIA SARA' PRESTATA CON LA SOSTITUZIONE O RIPARAZIONE GRATUITA,
PRESSO LA NOSTRA SEDE, DELLE PARTI CHE RISULTINO DIFETTOSE ALL'ORIGINE
PER VIZI DI FABBRICAZIONE.
NON SONO COPERTE DA GARANZIA TUTTE LE PARTI CHE DOVESSERO RISULTARE DIFETTOSE
A CAUSA DI NEGLIGENZA O TRASCURATEZZA NELL'USO, DI ERRATA INSTALLAZIONE,
DI MANUTENZIONE OPERATA DA PERSONALE NON AUTORIZZATO, DI DANNI DA TRASPORTO,
OVVERO DI CIRCOSTANZE CHE, COMUNQUE, NON POSSONO FARSI RISALIRE A DIFETTI DI
FABBRICAZIONE DELL'APPARECCHIO.
LA CASA COSTRUTTRICE DECLINA OGNI RESPONSABILITA' PER EVENTUALI DANNI CHE POSSONO,
DIRETTAMENTE O INDIRETTAMENTE, DERIVARE A PERSONE, COSE ED ANIMALI IN CONSEGUENZA
ALLA MANCATA OSSERVANZA DELLE INDICAZIONI RIPORTATE IN QUESTO LIBRETTO.