TI00138R/09/EN/05.

17 Products Solutions Services

71356457

Technical Information
iTEMP TMT84
Dual Input Temperature Transmitter

PROFIBUS® PA communication

Application Your benefits

• Temperature transmitter with 2 universal input channels and • Easy and standardized communication via PROFIBUS® PA
PROFIBUS® PA protocol for the conversion of different input Profile 3.02
signals into digital output signals • Straightforward design of measuring points in
• The transmitter stands out due to signal reliability, long-term Ex-areas through FISCO/FNICO conformity in accordance
stability, high precision and advanced diagnostics function with IEC 600079-27
(important in critical processes) • Diagnostics information according to NAMUR NE107
• For the highest level of safety, availability and risk reduction • Safe operation in hazardous areas thanks to international
• Universal input usable for RTD thermometer, thermocouple approvals
(TC), resistance (Ω) or voltage transmitter (mV) • High accuracy through sensor-transmitter matching
• DIN B style transmitter to fit in the smallest terminal heads or • Reliable operation with sensor monitoring and device
in remote housings in accordance with DIN EN 50446 hardware fault recognition
• Optional installation in field housings even for use in Ex d • Rapid no-tools wiring due to optional spring terminal
areas technology
• Compatibility mode for easy replacement of the previous
model iTEMP TMT184
 TMT84

Function and system design

Measuring principle Electronic recording and conversion of various input signals in industrial temperature measurement.

Measuring system

RTD/TC RTD/TC 1 x RTD/TC /

2 x RTD/TC

m n
A0007667

Application examples
m Two sensors with measuring input (RTD or TC) in remote installation with the following advantages: drift warning,
sensor backup function and temperature-dependent switching
n Built-in head transmitter - 1 x RTD/TC or 2 x RTD/TC as redundancy

Endress+Hauser offers a wide range of resistance thermometers, thermocouples and matching

thermowells.
In conjunction with these components, the temperature transmitter forms a complete measuring point
for various applications in the industrial sector.

Device architecture

PLC
Visualisation and monitoring
e. g. P View, FieldCare
and diagnostic software

PROFIBUS-DP

PROFIBUS-PA segment segment segment

IEC 61158-2 coupler coupler coupler
31.25 kbit/s FISCO

0 - 10 bar 0 - 10 bar

Measuring point with 32 devices per segment Measuring point with

installed TMT84 installed TMT84
A0009166-EN

System integration via PROFIBUS® PA

2 Endress+Hauser
TMT84

The temperature transmitter is a two-wire device with two measuring inputs. Using PROFIBUS® PA,
the device transfers converted signals from resistance thermometers and thermocouples in addition to
other resistance and millivolt signals. The device is powered via the PROFIBUS® PA bus and can be
installed as an intrinsically safe apparatus in zone 1 hazardous areas. The device is used for
instrumentation purposes in the terminal head form B as per DIN EN 50446. Data transfer takes place
via 4 analog input (AI) function blocks:
Sensor diagnosis functions
Sensor diagnoses such as cable open circuit, short-circuit, cable corrosion, wiring error and device
hardware error are supported. In addition, the work area of the sensor and the ambient temperature
are monitored.
2-channel functions
These functions increase the reliability and availability of the process values:
• Sensor backup switches to the second sensor if the primary sensor fails.
• Drift warning or alarm if the deviation between sensor 1 and sensor 2 is less than or greater than a
predefined limit value.
• Temperature-dependent switching between sensors which have advantages in different ranges.
Compatibility mode
For a easy replacement of the previous model iTEMP TMT184 with the TMT84 a compatibility mode
is available. The switching between the standard mode and compatibility mode in the iTEMP TMT84
is done automatically during the connection establishment of the cyclic communication.
The Following points have to receive attention:
• Only PROFIBUS® PA-Profile 3.0 is supported.
• Only 1-channel operation possible.
• The diagnostics and status handling is equal to the previous model TMT184.
• The previous model TMT184 software locking is not available.

Input
Measured variable Temperature (temperature linear transmission behavior), resistance and voltage.

Measuring range The transmitter records different measuring ranges depending on the sensor connection and input
signals (see "Type of input").

Endress+Hauser 3
 TMT84

Type of input It is possible to connect two sensors which are independent of each other. The measuring inputs are
not galvanically isolated from each other.

Type of input Designation Measuring range limits

Resistance thermometer Pt100 -200 to 850 °C (-328 to 1562 °F)

(RTD) Pt200 -200 to 850 °C (-328 to 1562 °F)
as per IEC 60751 Pt500 -200 to 250 °C (-328 to 482 °F)
(α = 0.00385) Pt1000 -200 to 250 °C (-238 to 482 °F)

as per JIS C1604-81 Pt100 -200 to 649 °C (-328 to 1200 °F)

(α = 0.003916)
as per DIN 43760 Ni100 -60 to 250 °C (-76 to 482 °F)
(α = 0.006180) Ni1000 -60 to 150 °C (-76 to 302 °F)

as per Edison Copper Winding Cu10 -100 to 260 °C (-148 to 500 °F)
No.15 (α = 0.004274)
as per Edison Curve Ni120 -70 to 270 °C (-94 to 518 °F)
(α = 0.006720)
as per GOST Pt50 -200 to 1100 °C (-328 to 2012 °F)
(α = 0.003911) Pt100 -200 to 850 °C (-328 to 1562 °F)

as per GOST Cu50, Cu100 -200 to 200 °C (-328 to 392 °F)

(α = 0.004280)
Pt100 (Callendar-Van 10 to 400 Ω
Dusen) 10 to 2000 Ω
10 to 400 Ω
Polynomial nickel 10 to 2000 Ω
10 to 400 Ω
Polynomial copper 10 to 2000 Ω

• Connection type: 2-wire, 3-wire or 4-wire connection, sensor current: ≤ 0.3 mA

• For 2-wire circuit, compensation for wire resistance possible (0 to 30 Ω)
• For 3-wire and 4-wire connection, sensor wire resistance up to max. 50 Ω per wire

Resistance transmitter Resistance Ω 10 to 400 Ω

10 to 2000 Ω

Thermocouples (TC) Recommended temperature range:

as per IEC 584, Part 1 Type A (W5Re-W20Re) (30) 0 to +2 500 °C (+32 to +4 532 °F) 0 to +2500 °C (+32 to 4532 °F)
Type B (PtRh30-PtRh6) (31) 40 to +1820 °C (104 to 3308 °F) +500 to +1820 °C (+932 to +3308 °F)
Type E (NiCr-CuNi) (34) -270 to +1000 °C (-454 to 1832 °F) -150 to +1000 °C (-238 to +1832 °F)
Type J (Fe-CuNi) (35) -210 to +1200 °C (-346 to 2192 °F) -150 to +1200 °C (-238 to +2192 °F)
Type K (NiCr-Ni) (36) -270 to +1372 °C (-454 to 2501 °F) -150 to +1200 °C (-238 to +2192 °F)
Type N (NiCrSi-NiSi) (37) -270 to +1300 °C (-454 to 2372 °F) -150 to +130 °C (-238 to +2372 °F)
Type R (PtRh13-Pt) (38) -50 to +1768 °C (-58 to 3214 °F) +50 to +1768 °C (+122 to +3214 °F)
Type S (PtRh10-Pt) (39) -50 to +1768 °C (-58 to 3214 °F) +50 to +1768 °C (+122 to +3214 °F)
Type T (Cu-CuNi) (40) -260 to +400 °C (-436 to 752 °F) -150 to +400 °C (-238 to +752 °F)

as per ASTM E988 Type C (W5Re-W26Re) (32) 0 to +2315 °C (32 to 4199 °F) 0 to +2000 °C (+32 to +3632 °F)
Type D (W3Re-W25Re) (33) 0 to +2315 °C (32 to 4199 °F) 0 to +2000 °C (+32 to +3632 °F)

as per DIN 43710 Type L (Fe-CuNi) (41) -200 to +900 °C (-328 to 1652 °F) -150 to +900 °C (-238 to +1652 °F)
Type U (Cu-CuNi) (42) -200 to +600 °C (-328 to 1112 °F) -150 to +600 °C (-238 to +1112 °F)
as per GOST Type L (NiCr-CuNi) (43) -200 to +800 °C (-328 to 1472 °F) -200 to +800 °C (-328 to +1472 °F)
R8.8585-2001
• Internal cold junction (Pt100)
• External cold junction: value adjustable from -40 to +85 °C (-40 to +185 °F)
• Maximum sensor resistance 10 kΩ (if the sensor resistance is greater than 10 kΩ, an error message is output in
accordance with NAMUR NE89)

Voltage transmitter (mV) Millivolt transmitter (mV) -20 to 100 mV

-5 to 30 mV

4 Endress+Hauser
TMT84

When assigning both sensor inputs, the following connection combinations are possible:

Sensor input 1

RTD or RTD or RTD or Thermocouple

resistance resistance resistance (TC), voltage
transmitter, 2- transmitter, 3- transmitter, 4- transmitter
wire wire wire

RTD or resistance
transmitter, 2-wire
  - 
RTD or resistance
transmitter, 3-wire
  - 
Sensor
input 2 RTD or resistance
- - - -
transmitter, 4-wire

Thermocouple (TC),
voltage transmitter
   

Input signal Input data: The transmitter is able to receive a cyclic value and its status sent by a master via
PROFIBUS® PA. That value and status is represented and can be read acyclically.

Output
Output signal • PROFIBUS® PA in accordance with EN 50170 Volume 2, IEC 61158-2 (MBP), galvanically isolated;
• FDE (Fault Disconnection Electronic) = 0 mA
• Data transmission rate: supported baud rate = 31.25 kBit/s
• Signal coding = Manchester II
• Output data:
Available values via AI blocks: temperature (PV), temp sensor 1 + 2, terminal temperature
• In a control system the transmitter always operates as a slave and, dependent on the application, can
exchange data with one or more masters.
• In accordance with IEC 60079-27, FISCO/FNICO

Breakdown information Status message in accordance with PROFIBUS® PA Profile 3.01/3.02 specification.

Linearization/transmission Temperature linear, resistance linear, voltage linear

behavior

Mains voltage filter 50/60 Hz

Galvanic isolation U = 2 kV AC (sensor input to the output)

Current consumption ≤ 11 mA

Switch-on delay 8s

Endress+Hauser 5
 TMT84

PROFIBUS® PA basic data Manufacturer spec. ID-no.: Profile 3.0 ID-no.: Manufacturer specific GSD

1551 (Hex) 9700 (Hex) EH021551.gsd

9701 (Hex) (Profile 3.01 EH3x1551.gsd)
9702 (Hex)
9703 (Hex)

Profile 3.0 GSD Device address or bus address Bitmaps

Pa139700.gsd 126 (default) EH_1551_d.bmp

Pa139701.gsd EH_1551_n.bmp
Pa139702.gsd EH_1551_s.bmp
Pa139703.gsd

If the TMT84 operates in the compatibily mode, the device is identifying with the manufactu-
rer specific ID-no.: 1523 (Hex) - TMT184 in the cyclic data exchange.

Brief description of the blocks Physical Block

The Physical Block contains all the data that clearly identify and characterize the device. It is like an
electronicdevice nameplate. In addition to parameters that are needed to operate the device on the
fieldbus, the Physical Block makes other information available such as the order code, device ID,
hardware revision, software revision, device release, etc. Furthermore the display settings can be
configured via the Physical Block.
Transducer Block "Sensor 1" and "Sensor 2"
The Transducer Blocks of the transmitter contain all the measurement-related and device-specific
parameters that are relevant for measuring the input variables.
Analog Input (AI)
In the AI function block, the process variables from the Transducer Blocks are prepared for subsequent
automation functions in the control system (e.g. scaling, limit value processing).

Power supply
Electrical connection

Sensor input 2 Bus connection

Sensor input 1
and supply voltage
RTD, Ω: 3- and 2-wire RTD, Ω: 4-, 3- and 2-wire
red
(black) 7
red red 6
(black) 7
TC, mV 6
1
red 5 +
TC, mV 5
1
+
2
white 4 4
-
-
white white 3 3
2
(yellow)
Display connection/
service interface
A0007285-EN

Terminal assignment of transmitter.

Supply voltage U = 9 to 32 V DC, polarity independent (max. voltage Ub = 35 V)

6 Endress+Hauser
TMT84

Performance characteristics
Response time 1 s per channel

Reference operating • Calibration temperature: + 25 °C ± 5 K (77 °F ± 9 °F)

conditions • Supply voltage: 24 V DC
• 4-wire circuit for resistance adjustment

Resolution Resolution A/D converter = 18 bit

Maximum measured error Typical values, according to DIN EN 60770, 25 °C ± 3 °C (77 °F ± 5,4 °F), supply voltage
24 VDC. The data concerning the various measured errors correspond to a standard deviation
of 2 σ (Gaussian normal distribution). These data include nonlinearity and repeatability.

Designation Measuring range Typical measured error (±)

Resistance thermometer Digital value 1)

(RTD) according to stan-
dard

IEC 60751:2008 Pt100 (1) 0.08 °C (0.14 °F)

0 to +200 °C (32 to +392 °F)
IEC 60751:2008 Pt1000 (4) 0.08 °C (0.14 °F)

GOST 6651-94 Pt100 (9) 0.07 °C (0.13 °F)

Thermocouples (TC)
according to standard

IEC 60584-1 Typ K (36) 0.31 °C (0.56 °F)

0 to +800 °C (32 to +1472 °F)
IEC 60584-1 Typ S (39) 0.97 °C (1.75 °F)

GOST R8.8585-2001 Typ L (43) 2.18 °C (3.92 °F)

1) Using fieldbus transmitted measured value

Measured error for resistance thermometer (RTD) and resistance transmitters

Measured error (±) Non-repeatability (±)

Digital1)
Standard Designation Measuring range
Maximum Relating to measured
value

Pt100 (1) ≤ 0.12 °C (0.21 °F) 0.06 °C (0.11 °F) + ≤ 0.05 °C (0.09 °F)
IEC 60751:2008
-200 to +850 °C 0.006% x (MW - MBA)

IEC 60751:2008 Pt100 (2) (-328 to +1562 °F) ≤ 0.30 °C (0.54 °F) 0.11 °C (0.2 °F) + 0.018% ≤ 0.13 °C (0.23 °F)
x (MW - MBA)

IEC 60751:2008 Pt500 (3) -200 to +510 °C ≤ 0.16 °C (0.29 °F) 0.05 °C (0.09 °F) + ≤ 0.08 °C (0.14 °F)
(-328 to +950 °F) 0.015% x (MW - MBA)

IEC 60751:2008 -200 to +250 °C 0.03 °C (0.05 °F) + ≤ 0.05 °C (0.09 °F)
Pt1000 (4)
(-328 to +482 °F) 0.013% x (MW - MBA)
≤ 0.09 °C (0.16 °F)
JIS C1604:1984 Pt100 (5) -200 to +510 °C 0.05 °C (0.09 °F) + ≤ 0.04 °C (0.07 °F)
(-328 to +950 °F) 0.006% x (MW - MBA)

GOST 6651-94 Pt50 (8) -185 to +1100 °C ≤ 0.20 °C (0.36 °F) 0.1 °C (0.18 °F) + 0.008% ≤ 0.11 °C (0.2 °F)
(-301 to +2012 °F) x (MW - MBA)

GOST 6651-94 Pt100 (9) -200 to +850 °C ≤ 0.11 °C (0.2 °F) ≤ 0.05 °C (0.09 °F)
(-328 to +1562 °F)
0.05 °C (0.09 °F) +
DIN 43760 IPTS-68 Ni100 (6) -60 to 250 °C ≤ 0.05 °C (0.09 °F) 0.006% x (MW - MBA)
≤ 0.03 °C (0.05 °F)
DIN 43760 IPTS-68 Ni120 (7) (-76 to 482 °F)

Endress+Hauser 7
 TMT84

OIML R84:2003 / GOST Cu50 (10) ≤ 0.11 °C (0.2 °F) 0.09 °C (0.16 °F) + ≤ 0.05 °C (0.09 °F)
6651-2009 -60 to +250 °C 0.006% x (MW - MBA)

OIML R84:2003 / GOST Cu100 (11) (-76 to +482 °F) ≤ 0.06 °C (0.11 °F) ≤ 0.04 °C (0.07 °F)
6651-2009

OIML R84:2003 / GOST Ni100 (12) 0.05 °C (0.09 °F) +

6651-2009 -60 to +180 °C 0.003% x (MW - MBA)
≤ 0.05 °C (0.09 °F) ≤ 0.03 °C (0.05 °F)
OIML R84:2003 / GOST Ni120 (13) (-76 to +356 °F)
6651-2009

OIML R84:2003 / GOST Cu50 (14) -50 to +200 °C ≤ 0.11 °C (0.2 °F) 0.1 °C (0.18 °F) + 0.004% ≤ 0.07 °C (0.13 °F)
6651-94 (-58 to +392 °F) x (MW - MBA)

Resistance transmit- Resistance Ω 10 to 400 Ω 32 mΩ - 15 mΩ

ters
10 to 2000 Ω 300 mΩ - ≤ 200 mΩ

1) Using fieldbus transmitted measured value

MW = Measured value
MBA = Measuring range start of the respective sensor

Measured error for thermocouples (TC) and voltage transmitters

Measured error (±) Non-repeatability (±)
Thermocouples (TC)
Designation Measuring range Digital1)
according to standard
Maximum Relating to measured value

Type A (30) 0 to +2500 °C ≤ 1.33 °C (2.39 °F) 0.8 °C (1.44 °F) + 0.021% x ≤ 0.52 °C (0.94 °F)
IEC 60584-1
(+32 to +4532 °F) MW

IEC 60584-1 Type B (31) +500 to +1820 °C ≤ 1.50 °C (2.7 °F) 1.5 °C (2.7 °F) - 0.06% x ≤ 0.67 °C (1.21 °F)
(+932 to +3308 °F) (MW - MBA)

IEC 60584-1 / ASTM Type C (32) ≤ 0.66 °C (1.19 °F) 0.55 °C (1 °F) + 0.0055% x ≤ 0.33 °C (0.59 °F)
E988-96 0 to +2000 °C MW

ASTM E988-96 (+32 to +3632 °F) ≤ 0.75 °C (1.35 °F) 0.75 °C (1.44 °F) - 0.008% ≤ 0.41 °C (0.74 °F)
Type D (33)
x MW

IEC 60584-1 Type E (34) -150 to +1000 °C ≤ 0.22 °C (0.4 °F) 0.22 °C (0.40 °F) - 0.006% ≤ 0.07 °C (0.13 °F)
(-238 to +2192 °F) x (MW - MBA)

IEC 60584-1 Type J (35) ≤ 0.27 °C (0.48 °F) 0.27 °C (0.49 °F) - 0.005% ≤ 0.08 °C (0.14 °F)
-150 to +1200 °C x (MW - MBA)

IEC 60584-1 Type K (36) (-238 to +2192 °F) ≤ 0.35 °C (0.63 °F) 0.35 °C (0.63 °F) - 0.005% ≤ 0.11 °C (0.20 °F)
x (MW - MBA)

IEC 60584-1 Type N (37) -150 to +1300 °C ≤ 0.48 °C (0.86 °F) 0.48 °C (0.86 °F) - 0.014%
≤ 0.16 °C (0.29 °F)
(-238 to +2372 °F) x (MW - MBA)

IEC 60584-1 Type R (38) ≤ 1.12 °C (2.0 °F) 1.12 °C (2 °F) - 0.03% x ≤ 0.76 °C (1.37 °F)
+50 to +1768 °C MW

IEC 60584-1 Type S (39) (+122 to +3214 °F) ≤ 1.15 °C (2.07 °F) 1.15 °C (2.07 °F) - 0.022% ≤ 0.74 °C (1.33 °F)
x MW

IEC 60584-1 Type T (40) -150 to +400 °C ≤ 0.36 °C (0.47 °F) 0.36 °C (0.47 °F) - 0.04% x ≤ 0.11 °C (0.20 °F)
(-238 to +752 °F) (MW - MBA)

DIN 43710 Type L (41) -150 to +900 °C ≤ 0.29 °C (0.52 °F) 0.29 °C (0.52 °F) - 0.009%
≤ 0.07 °C (0.13 °F)
(-238 to +1652 °F) x (MW - MBA)

DIN 43710 Type U (42) -150 to +600 °C ≤ 0.33 °C (0.6 °F) 0.33 °C (0.6 °F) - 0.028% x ≤ 0.10 °C (0.18 °F)
(-238 to +1112 °F) (MW - MBA)

GOST R8.8585-2001 Type L (43) -200 to +800 °C ≤ 2.2 °C (4.0 °F) 2.2 °C (4 °F) - 0.015% x ≤ 0.15 °C (0.27 °F)
(-328 to +1472 °F) (MW - MBA)

Voltage transmitter (mV) -20 to 100 mV 10 μV - 4 μV

1) Using fieldbus transmitted measured value

8 Endress+Hauser
TMT84

Sample calculation with Pt100, measuring range 0 to +200 °C (32 to +392 °F), ambient temperature
+25 °C (+77 °F), supply voltage 24 V:
Measured error = 0.06 °C + 0.006% x (200 °C - (-200 °C)): 0.084 °C (0.151 °F)

Sample calculation with Pt100, measuring range 0 to +200 °C (32 to +392 °F), ambient temperature
+35 °C (+95 °F), supply voltage 30 V:
Measured error = 0.06 °C + 0.006% x (200 °C - (-200 °C)): 0.084 °C (0.151 °F)

Influence of ambient temperature = (35 - 25) x (0.002% x 200 °C - (-200 °C)), 0.08 °C (0.144 °F)
min. 0.005 °C

Influence of supply voltage = (30 - 24) x (0.002 % x 200 °C - (-200 °C)), 0.048 °C (0.086 °F)
min. 0.005 °C

Total measured error: √(Measured error² + influence of ambient temperature² + 0.126 °C (0.227 °F)
influence of supply voltage²:

Sensor transmitter matching RTD sensors are one of the most linear temperature measuring elements. Nevertheless, the output
must be linearized. To improve temperature measurement accuracy significantly, the device enables
the use of two methods:
• Callendar-Van Dusen coefficients (Pt100 resistance thermometer)
The Callendar-Van Dusen equation is described as:

-100 3

The coefficients A, B and C are used to match the sensor (platinum) and transmitter in order to
improve the accuracy of the measuring system. The coefficients for a standard sensor are specified
in IEC 751. If no standard sensor is available or if greater accuracy is required, the coefficients for
each sensor can be determined specifically by means of sensor calibration.

• Linearization for copper/nickel resistance thermometers (RTD)

The polynomial equations for nickel are described as:

-100 3

The equations for copper, subject to temperature, are described as:

T = -50 °C to 200 °C (-58 °F to 392 °F)

T = -180 °C to -50 °C (-292 °F to -58 °F)

These coefficients A, B and C are used for the linearization of nickel or copper resistance
thermometers (RTD). The exact values of the coefficients derive from the calibration data and are
specific to each sensor.
Sensor transmitter matching using one of the above-named methods significantly improves the
temperature measurement accuracy of the entire system. This is due to the fact that to calculate the
temperature measured, the transmitter uses the specific data pertaining to the connected sensor
instead of using the standardized sensor curve data.

Endress+Hauser 9
 TMT84

Operational influences The data concerning the various measured errors correspond to a standard deviation of 2 σ (Gaussian
normal distribution)

Designation Standard Ambient temperature: Supply voltage:

effect (±) when ambient temperature changes by effect (±) when supply voltage changes by 1 V
1 °C (1.8 °F)
Digital1) Digital1)

Maximum Relating to measured value Maximum Relating to measured

value

Resistance thermometer (RTD)

Pt100 (1) ≤ 0.02 °C (0.036 °F) 0.002% x (MW - MBA). ≤ 0.12 °C (0.21 °F) 0.002% x (MW - MBA).
min. 0.005 °C (0.009 °F) min. 0.005 °C (0.009 °F)

Pt200 (2) ≤ 0.026 °C (0.047 °F) - ≤ 0.026 °C (0.047 °F) -

Pt500 (3) IEC60751:2008 ≤ 0.014 °C (0.025 °F) 0.002% x (MW - MBA), ≤ 0.014 °C (0.025 °F) 0.002% x (MW - MBA),
min. 0.009 °C (0.016 °F) min. 0.009 °C (0.016 °F)

Pt1000 (4) 0.002% x (MW - MBA), 0.002% x (MW - MBA),

min. 0.004 °C (0.007 °F) min. 0.004 °C (0.007 °F)
≤ 0.01 °C (0.018 °F) ≤ 0.01 °C (0.018 °F)
Pt100 (5) JIS C1604:1984 0.002% x (MW - MBA), 0.002% x (MW - MBA),
min. 0.005 °C (0.009 °F) min. 0.005 °C (0.009 °F)

Pt50 (8) ≤ 0.03 °C (0.054 °F) 0.002% x (MW - MBA), ≤ 0.03 °C (0.054 °F) 0.002% x (MW - MBA),
min. 0.01 °C (0.018 °F) min. 0.01 °C (0.018 °F)
GOST 6651-94
Pt100 (9) ≤ 0.02 °C (0.036 °F) 0.002% x (MW - MBA), ≤ 0.02 °C (0.036 °F) 0.002% x (MW - MBA),
min. 0.005 °C (0.009 °F) min. 0.005 °C (0.009 °F)

Ni100 (6) DIN 43760 IPTS-68 - -

≤ 0.005 °C (0.009 °F) ≤ 0.005 °C (0.009 °F)
Ni120 (7) - -

Cu50 (10) - -

Cu100 (11) ≤ 0.008 °C (0.014 °F) 0.002% x (MW - MBA), ≤ 0.008 °C (0.014 °F) 0.002% x (MW - MBA),
OIML R84:2003 / min. 0.004 °C (0.007 °F) min. 0.004 °C (0.007 °F)
GOST 6651-2009
Ni100 (12) - -
≤ 0.004 °C (0.007 °F) ≤ 0.004 °C (0.007 °F)
Ni120 (13) - -

Cu50 (14) OIML R84:2003 / ≤ 0.008 °C (0.014 °F) - -

≤ 0.008 °C (0.014 °F)
GOST 6651-94

Resistance transmitters (Ω)

10 to 400 Ω ≤ 6 mΩ 0.0015% x (MW - MBA), ≤ 6 mΩ 0.0015% x (MW - MBA),

min. 1.5 mΩ min. 1.5 mΩ
-
10 to 2000 Ω ≤ 30 mΩ 0.015% x (MW - MBA), ≤ 30 mΩ 0.015% x (MW - MBA),
min. 15 mΩ min. 15 mΩ

1) Using fieldbus transmitted measured value

Ambient temperature: Supply voltage:

effect (±) when ambient temperature changes by effect (±) when supply voltage changes by 1 V
Designation Standard 1 °C (1.8 °F)

Digital1) Digital1)

Maximum Relating to measured value Maximum Relating to measured

value

Thermocouples (TC)

Type A (30) IEC 60584-1 ≤ 0.14 °C (0.25 °F) 0.0055% x MW, ≤ 0.14 °C (0.25 °F) 0.0055% x MW,
min. 0.03 °C (0.05 °F) min. 0.03 °C (0.005 °F)

Type B (31) IEC 60584-1 ≤ 0.06 °C (0.11 °F) - ≤ 0.06 °C (0.11 °F) -

Type C (32) IEC 60584-1 / ≤ 0.09 °C (0.16 °F) 0.0045% x MW, ≤ 0.09 °C (0.16 °F) 0.0045% x MW,
ASTM E988-96 min. 0.03 °C (0.05 °F) min. 0.03 °C (0.05 °F)

10 Endress+Hauser
TMT84

Ambient temperature: Supply voltage:

effect (±) when ambient temperature changes by effect (±) when supply voltage changes by 1 V
Designation Standard 1 °C (1.8 °F)

Digital1) Digital1)

Type D (33) ASTM E988-96 ≤ 0.08 °C (0.14 °F) 0.004% x MW, ≤ 0.08 °C (0.14 °F) 0.004% x MW,
min. 0.035 °C (0.063 °F) min. 0.035 °C (0.063 °F)

Type E (34) ≤ 0.03 °C (0.05 °F) 0.003% x (MW - MBA), ≤ 0.03 °C (0.05 °F) 0.003% x (MW - MBA),
min. 0.016 °C (0.029 °F) min. 0.016 °C (0.029 °F)

Type J (35) ≤ 0.02 °C (0.04 °F) 0.0028% x (MW - MBA), ≤ 0.02 °C (0.04 °F) 0.0028% x (MW - MBA),
min. 0.02 °C (0.036 °F) min. 0.02 °C (0.036 °F)

Type K (36) ≤ 0.04 °C (0.07 °F) 0.003% x (MW - MBA), ≤ 0.04 °C (0.07 °F) 0.003% x (MW - MBA),
min. 0.013 °C (0.023 °F) min. 0.013 °C (0.023 °F)
IEC 60584-1
Type N (37) ≤ 0.04 °C (0.07 °F) 0.0028% x (MW - MBA), ≤ 0.04 °C (0.07 °F) 0.0028% x (MW - MBA),
min. 0.020 °C (0.036 °F) min. 0.020 °C (0.036 °F)

Type R (38) ≤ 0.06 °C (0.11 °F) 0.0035% x MW, ≤ 0.06 °C (0.11 °F) 0.0035% x MW,
min. 0.047 °C (0.085 °F) min. 0.047 °C (0.085 °F)

Type S (39) ≤ 0.05 °C (0.09 °F) - ≤ 0.05 °C (0.09 °F) -

Type T (40) ≤ 0.01 °C (0.02 °F) - ≤ 0.01 °C (0.02 °F) -

Type L (41) DIN 43710 ≤ 0.02 °C (0.04 °F) - ≤ 0.02 °C (0.04 °F) -

Type U (42) DIN 43710 ≤ 0.01 °C (0.02 °F) - ≤ 0.01 °C (0.02 °F) -

Type L (43) GOST R8.8585- ≤ 0.02 °C (0.04 °F) - ≤ 0.02 °C (0.04 °F) -
2001

Voltage transmitter (mV)

-20 to 100 mV - ≤ 3 μV - ≤ 3 μV -

1) Using fieldbus transmitted measured value

MW = Measured value
MBA = Measuring range start of the respective sensor

Long term drift resistance thermometer (RTD) and resistance transmitter

Long term drift (±)
Designation Standard
After 1 year After 3 years After 5 years

Maximum

Pt100 (1) IEC 60584-1 ≤ 0.03 °C (0.05 °F) + 0.024% x ≤ 0.042 °C (0.076 °F)+ 0.035% x ≤ 0.051 °C (0.092 °F) + 0.037% x
measuring span measuring span measuring span

Pt200 (2) IEC 60584-1 ≤ 0.17 °C (0.31 °F) + 0.016% x ≤ 0.28 °C (0.5 °F) + 0.022% x ≤ 0.343 °C (0.617 °F) + 0.025% x
measuring span measuring span measuring span

Pt500 (3) IEC 60584-1 / ≤ 0.067 °C (0.121 °F) + 0.018% x ≤ 0.111 °C (0.2 °F)+ 0.025% x ≤ 0.137 °C (0.246 °F) + 0.028% x
ASTM E988-96 measuring span measuring span measuring span

Pt1000 (4) ASTM E988-96 ≤ 0.034 °C (0.06 °F) + 0.02% x ≤ 0.056 °C (0.1 °F) + 0.029% x ≤ 0.069 °C (0.124 °F)+ 0.032% x
measuring span measuring span measuring span

Endress+Hauser 11
 TMT84

Long term drift (±)

Designation Standard
After 1 year After 3 years After 5 years

Pt100 (5) ≤ 0.03 °C (0.054 °F)+ 0.022% x ≤ 0.042 °C (0.076 °F) + 0.032% x ≤ 0.051 °C (0.092 °F) + 0.034% x
measuring span measuring span measuring span

Pt50 (8) ≤ 0.055 °C (0.01 °F) + 0..023% x ≤ 0.089 °C (0.16 °F) + 0.032% x ≤ 0.1 °C (0.18 °F)+ 0.035% x
measuring span measuring span measuring span

Pt100 (9) ≤ 0.03 °C (0.054 °F)+ 0.024% x ≤ 0.042 °C (0.076 °F) + 0.034% x ≤ 0.051 °C (0.092 °F) + 0.037% x
measuring span measuring span measuring span

Ni100 (6) ≤ 0.025 °C (0.045 °F) + 0.016% x ≤ 0.042 °C (0.076 °F) + 0.02% x ≤ 0.047 °C (0.085 °F) + 0.021% x
IEC 60584-1
measuring span measuring span measuring span

Ni120 (7) ≤ 0.02 °C (0,036 °F) + 0.018% x ≤ 0.032 °C (0.058 °F) + 0.024% x ≤ 0.036 °C (0.065 °F) + 0.025% x
measuring span measuring span measuring span

Cu50 (10) ≤ 0.053 °C (0.095 °F) + 0.013% x ≤ 0.084 °C (0.151 °F) + 0.016% x ≤ 0.094 °C (0.169 °F) + 0.016% x
measuring span measuring span measuring span

Cu100 (11) ≤ 0.027 °C (0.049 °F) + 0.019% x ≤ 0.042 °C (0.076 °F) + 0.026% x ≤ 0.047 °C (0.085 °F) + 0.027% x
measuring span measuring span measuring span

Ni100 (12) DIN 43710 ≤ 0.026 °C (0.047 °F)+ 0.015% x ≤ 0.04 °C (0.076 °F) + 0.02% x ≤ 0.046 °C (0.083 °F) + 0.02% x
measuring span measuring span measuring span

Ni120 (13) DIN 43710 ≤ 0.021 °C (0.038 °F) + 0.017% x ≤ 0.034 °C (0.061 °F) + 0.022% x ≤ 0.038 °C (0.068 °F) + 0.023% x
measuring span measuring span measuring span

Cu50 (14) GOST R8.8585- ≤ 0.056 °C (0.1 °F)+ 0.009% x ≤ 0.089 °C (0.16 °F) + 0.011% x ≤ 0.1 °C (0.18 °F) + 0.011% x
2001 measuring span measuring span measuring span

Resistance transmitters (Ω)

10 to 400 Ω - ≤ 10 mΩ + 0.022% x measuring ≤ 14 mΩ + 0.031% x measuring ≤ 16 mΩ + 0.033% x measuring

span span span

10 to 2000 Ω - ≤ 144 mΩ + 0.019% x measuring ≤ 238 mΩ + 0.026% x measuring ≤ 294 mΩ + 0.028% x measuring
span span span

Long term drift thermocouple (TC) and voltage transmitter

Long term drift (±)
Designation Standard
After 1 year After 3 years After 5 years

Maximum

Type A (30) ≤ 0.17 °C (0.306 °F) + 0.021% x ≤ 0.27 °C (0.486 °F) + 0.03% x ≤ 0.38 °C (0.683 °F) + 0.035% x
measuring span measuring span measuring span

Type B (31) ≤ 0.5 °C (0.9 °F) ≤ 0.75 °C (1.35 °F) ≤ 1.0 °C (1.8 °F)

Type C (32) IEC60751:2008 ≤ 0.15 °C (0.27 °F) + 0.018% x ≤ 0.24 °C (0.43 °F) + 0.026% x ≤ 0.34 °C (0.61 °F) + 0.027% x
measuring span measuring span measuring span

Type D (33) ≤ 0.21 °C (0.38 °F) + 0.015% x ≤ 0.34 °C (0.61 °F)+ 0.02% x ≤ 0.47 °C (0.85 °F)+ 0.02% x
measuring span measuring span measuring span

Type E (34) JIS C1604:1984 ≤ 0.06 °C (0.11 °F) + 0.018% x ≤ 0.09 °C (0.162 °F) + 0.025% x ≤ 0.13 °C (0.234 °F) + 0.026% x
measuring span measuring span measuring span

Type J (35) ≤ 0.06 °C (0.11 °F) + 0.019% x ≤ 0.1 °C (0.18 °F) + 0.025% x ≤ 0.14 °C (0.252 °F) + 0.027% x
measuring span measuring span measuring span
GOST 6651-94
Type K (36) ≤ 0.09 °C (0.162 °F) + 0.017% x ≤ 0.14 °C (0.252 °F) + 0.023% x ≤ 0.19 °C (0.342 °F) + 0.024% x
(MW + 150 °C (270 °F)) measuring span measuring span

Type N (37) ≤ 0.13 °C (0.234 °F) + 0.015% x ≤ 0.2 °C (0.36 °F) + 0.02% x ≤ 0.28 °C (0.5 °F) + 0.02% x
(MW + 150 °C (270 °F)) measuring span measuring span
DIN 43760 IPTS-68
Type R (38) ≤ 0.31 °C (0.558 °F) + 0.011% x ≤ 0.5 °C (0.9 °F) + 0.013% x ≤ 0.69 °C (1.241 °F) + 0.011% x
(MW - 50 °C (90 °F)) measuring span measuring span

12 Endress+Hauser
TMT84

Long term drift (±)

Designation Standard
After 1 year After 3 years After 5 years

Type S (39) ≤ 0.31 °C (0.558 °F) + 0.011% x ≤ 0.5 °C (0.9 °F) + 0.013% x ≤ 0.7 °C (1.259 °F) + 0.011% x
measuring span measuring span measuring span

Type T (40) ≤ 0.09 °C (0.162 °F) + 0.011% x ≤ 0.15 °C (0.27 °F)+ 0.013% x ≤ 0.2 °C (0.36 °F) + 0.012% x
OIML R84:2003 / measuring span measuring span measuring span

Type L (41) GOST 6651-2009 ≤ 0.06 °C (0.108 °F) + 0.017% x ≤ 0.1 °C (0.18 °F)+ 0.022% x ≤ 0.14 °C (0.252 °F) + 0.022% x
measuring span measuring span measuring span

Type U (42) ≤ 0.09 °C (0.162 °F) + 0.013% x ≤ 0.14 °C (0.252 °F)+ 0.017% x ≤ 0.2 °C (0.360 °F)+ 0.015% x
measuring span measuring span measuring span

Type L (43) OIML R84:2003 / ≤ 0.08 °C (0.144 °F) + 0.015% x ≤ 0.12 °C (0.216 °F) + 0.02% x ≤ 0.17 °C (0.306 °F) + 0.02% x
GOST 6651-94 measuring span measuring span measuring span

Voltage transmitter (mV)

-20 to 100 mV - ≤ 2 μV + 0.022% x measuring ≤ 3.5 μV + 0.03% x measuring ≤ 4.7 μV + 0,033% x measuring
span span span

Influence of reference point Pt100 DIN EN 60751 Cl. B, internal reference point for thermocouples TC
(cold junction)

Installation
Installation instructions • Mounting location:

A B

12
0
(4 mm
.72
in)

12
0
C (4 mm
.72
in)

A0016762

A: Terminal head as per DIN EN 50446 form B, direct installation onto insert with cable entry (middle hole 7 mm (0.28 in))
B: Separated from process in field housing, wall or pipe mounting
C: With DIN rail clip on top-hat rail as per IEC 60715 (TH35)

• Orientation:
No restrictions

Endress+Hauser 13
 TMT84

Environment

Ambient temperature range -40 to +85 °C (-40 to +185 °F), for hazardous areas see Ex documentation (XA, CD)

Storage temperature -40 to +100 °C (-40 to +212 °F)

Altitude up to 4000 m (4374.5 yd) above mean sea level in accordance with IEC 61010-1, CSA 1010.1-92

Climate class as per IEC 60654-1, Class C

Humidity • Condensation as per IEC 60068-2-33 permitted

• Max. rel. humidity: 95% as per IEC 60068-2-30

Degree of protection • IP00 with screw terminals. In the installed state, it depends on the terminal head or field housing
used.
• IP30 with spring terminals
• IP66/67 (NEMA Type 4x encl.) when installed in field housing TA30A, TA30D or TA30H

Shock and vibration 10 to 2000 Hz for 5g as per IEC 60068-2-6

resistance

Electromagnetic CE compliance
compatibility (EMC) EMC to all relevant requirements of the IEC/EN 61326- series and NAMUR NE21. For details see
declaration of conformity.
Maximum measured error <1% of measuring range
Interference immunity: as per IEC/EN 61326 series (industrial environment) / NAMUR NE21
Interference emissions: as per IEC 61326-1 Class B

Measuring category Measuring category II as per IEC 61010-1. The measuring category is provided for measuring on power
circuits that are directly connected electrically with the low-voltage network.

Degree of contamination Pollution degree 2 as per IEC 61010-1.

14 Endress+Hauser
TMT84

Mechanical construction
Design, dimensions Specifications in mm (in)
Head transmitter

 5 (0.2)
C

 7 (0.28)
A

 44 (1.73)
33 (1.3)
B

24.1 (0.95)
A0007301

Model with screw terminals

Pos. A: Spring range L ≥5 mm (not applicable to US - M4 mounting screws)
Pos. B: Fixing elements for detachable measured value display
Pos. C: Interface for contacting measured value display

28.1 (1.11)
A0007672

Model with spring terminals. The same dimensions except for height of housing.

Field housings
All terminal heads have an internal shape and size in accordance with DIN EN 50446, flat face and a
thermometer connection of M24x1.5. Cable glands: M20x1.5

TA30A Specification

• Two cable entries

107.5 (4.23) • Temperature: -50 °C to +150 °C (-58 °F to +302 °F) without
cable gland
• Material: aluminum, polyester powder coated
68.5 (2.7)

Seals: silicone
15.5 (0.6)

• Cable entry incl. glands: ½"NPT and M20x1.5

• Head color: blue RAL 5012
• Cap color: gray RAL 7035
• Weight: 330 g (11.64 oz)
28
(1.1)
78 (3.1)
A0009820

Endress+Hauser 15
 TMT84

TA30A with display window in cover Specification

• Two cable entries

107.5 (4.23) • Temperature: -50 °C to +150 °C (-58 °F to +302 °F) without
cable gland
• Material: aluminum, polyester powder coated
Seals: silicone

91.6 (3.61)
• Cable entry incl. glands: ½"NPT und M20x1.5

15.5 (0.6)
• Head color: blue RAL 5012
• Cap color: gray RAL 7035
• Weight: 420 g (14.81 oz)

28
(1.1)78 (3.1)

A0009821

TA30H Specification

• Flameproof (XP) version, explosion-protected, captive screw

125 (4.92) cap, with two cable entries
• Temperature: -50 °C to +150 °C (-58 °F to +302 °F) for rubber
seal without cable gland (observe max. permitted tempera-
ture of the cable gland!)
89.5 (3.52)

• Material: aluminum; polyester powder coated

20.5 (0.8)

• Cable entry glands: ½"NPT, M20x1.5

• Head color: blue RAL 5012
• Cap color: gray RAL 7035
• Weight: 640 g (22.6 oz)

28
(1.1)
78 (3.01)
A0009832

TA30H with display window in cover Specification

• Flameproof (XP) version, explosion-protected, captive screw

125 (4.92) cap, with two cable entries
• Temperature: -50 °C to +150 °C (-58 °F to +302 °F) for rubber
seal without cable gland (observe max. permitted tempera-
ture of the cable gland!)
• Material: aluminum; polyester powder coated
115 (4.53)

• Cable entry glands: ½"NPT, M20x1.5

• Head color: blue RAL 5012
20.5 (0.8)

• Cap color: gray RAL 7035

• Weight: 860 g (30.33 oz)

28
(1.1)
78 (3.01)
A0009831

16 Endress+Hauser
TMT84

TA30D Specification

• Two cable entries

107.5 (4.23) • Temperature: -50 °C to +150 °C (-58 °F to +302 °F) without
cable gland
• Material: aluminum, polyester powder coated
Seals: silicone
• Cable entry incl. glands: ½"NPT, M20x1.5

110 (4.3)
• Two head transmitters can be mounted. In the standard ver-
sion, one transmitter is mounted in the terminal head cover

15.5 (0.6)
and an additional terminal block is installed directly on the
insert.
• Head color: blue RAL 5012
• Cap color: gray RAL 7035
• Weight: 390 g (13.75 oz)
28
(1.1) 78 (3.1)
A0009822

Maximum ambient temperature for cable glands and fieldbus connectors

Type Temperature range

Cable gland polyamide ½" NPT, M20x1.5 (non-Ex) -40...+100 °C (-40...+212 °F)

Cable gland polyamide M20x1.5 (for dust ignition-proof area) -20...+95 °C (-4...+203 °F)

Cable gland brass ½" NPT, M20x1.5 (for dust ignition-proof area) -20...+130 °C (-4...+266 °F)

Fieldbus connector (M12x1 PA, 7/8" FF) -40...+105 °C (-40...+221 °F)

Weight • Head transmitter: approx. 40 to 50 g (1.4 to 1.8 oz)

• Field housing: see specifications

Material All materials used are RoHS-compliant.

Head transmitter
• Housing: Polycarbonate (PC), complies with UL94 HB flammability standard (HB: horizontal burning
test)
• Terminals
Screw terminals: Nickel-plated brass and gold-plated contact
Spring terminals: Tin-plated brass, contact spring V2A
• Potting: WEVO PU 403 FP / FL, according to UL94 V0 flammability standard (V0: vertical burning
test)
Field housing: see specifications

Terminals Choice of screw or spring terminals (see "Design, dimensions" diagram) for sensor and fieldbus wires:

Terminals version Wire version Conductor cross-section

Screw terminals (with latches at the Rigid or flexible ≤ 2.5 mm2 (14 AWG)
fieldbus terminals for easy connection
of a handheld terminal, e.g. DXR375)

Spring terminals Rigid or flexible 0.2...1.5 mm2 (24...16 AWG)

Stripped length = min. 10 mm (0.39
Flexible with wire-end ferrules 0.25...1.5 mm2 (24...16 AWG)
in)
without plastic ferrule

Flexible with wire-end ferrules 0.25...0.75 mm2 (24...18 AWG)

with plastic ferrule

No ferrules have to be used when connecting flexible wires to spring terminals.

Endress+Hauser 17
 TMT84

Operability
Display and operating There are no display or operating elements present at the transmitter.
elements Optional the plug-on display TID10 can be used in connection with the transmitter. It will display
information regarding the actual measured value and the measurement point identification. In the
event of a fault in the measurement chain this will be displayed in inverse color showing the channel
ident and diagnostics code. DIP-switches can be found on the rear of the display. This enables the
hardware set-up such as the PROFIBUS® device address.

a0009818

Pluggable display TID10

If the transmitter is installed in a field housing and used with a display, a housing with glas window
needs to be used.

Remote operation The configuration of PROFIBUS® PA functions and of device-specific parameters is performed via
fieldbus communication. Special configuration systems provided by various manufacturers are
available for this purpose.

Configuration software

Endress+Hauser FieldCare (DTM)

SIMATIC PDM (EDD)

Sources of supply of the device data files (GSD) and device drivers:
• GSD-file: www.endress.com (→ Download → Software)
• Profile GSD-file: www.profibus.com
• FieldCare/DTM, SIMATIC PDM (EDD): www.endress.com (→ Download → Software)

Bus address The device address or bus address is set up either with the configuration software or via DIP switches
on the optional display.

18 Endress+Hauser
TMT84

Certificates and approvals

CE-Mark The measuring system meets the legal requirements of the applicable EC guidelines. These are listed
in the corresponding EC Declaration of Conformity together with the standards applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.

Hazardous area approvals For further details on the ailable Ex versions (ATEX, CSA, FM, etc.), please contact your nearest
Endress+Hauser sales organisation. All relevant data for hazardous areas can be found in separate Ex
documentation. If required, please request copies from us or your Endress+Hauser sales organisation.

UL UL recognized component (see www.ul.com/database, search for keyword "E225237"

Other standards and • IEC 60529:

guidelines Degrees of protection through housing (IP code)
• IEC 61158-2:
Fieldbus standard
• IEC 61326-1:2007:
Electromagnetic compatibility (EMC requirements)
• IEC 60068-2-27 and IEC 60068-2-6:
Shock and vibration resistance
• NAMUR
International user association of automation technology in process industries

CSA GP CSA General Purpose

Certification PROFIBUS® PA The temperature transmitter is certified and registered by the PNO (PROFIBUS® user organization
e.V.). The device thus meets all the requirements of the specifications following:
• Certified according to PROFIBUS® PA Profile 3.02
• The device can also be operated with certified devices of other manufacturers (interoperability)

Ordering information
Detailed ordering information is available from the following sources:
• In the Product Configurator on the Endress+Hauser website:
www.endress.com → Click "Corporate" → Select your country → Click "Products" → Select the product
using the filters and search field → Open product page
→ The "Configure" button to the right of the product image opens the Product Configurator.
• From your Endress+Hauser Sales Center: www.endress.com/worldwide
Product Configurator - the tool for individual product configuration:
• Up-to-the-minute configuration data
• Depending on the device: Direct input of measuring point-specific information such as measuring
range or operating language
• Automatic verification of exclusion criteria
• Automatic creation of the order code and its breakdown in PDF or Excel output format
• Ability to order directly in the Endress+Hauser Online Shop

Endress+Hauser 19
 TMT84

Accessories
Various accessories, which can be ordered with the device or subsequently from Endress+Hauser, are
available for the device. Detailed information on the order code in question is available from your
local Endress+Hauser sales center or on the product page of the Endress+Hauser
website:www.endress.com.
The following accessories are contained in the scope of delivery:
• Multi-language Brief Operating Instructions as hard copy
• Supplementary documentation ATEX:
ATEX Safety instructions (XA), Control Drawings (CD)
• Mounting material for head transmitter
• Mounting material for field housings (pipe or wall mounting)

Type Order code

Display TID10 for Endress+Hauser transmitters iTEMP TMT8x, pluggable TID10-xx

Field housing TA30x for Endress+Hauser head transmitter TA30x-xx

DIN rail clip according to IEC 60715 (TH35) for head transmitter 51000856
mounting without securing screws

Standard - DIN mounting set (2 screws + springs, 4 securing disks and 1 71044061
display connector cover)

US - M4 mounting screws (2 screws M4 and 1 display connector cover) 71044062

Fieldbus connector Threaded connection Cable connecting

(PROFIBUS® PA): thread
• M20x1.5 71090687
• NPT ½" • M12 71005802
• M20x1.5 • M12 71089147
• 7/8"

Stainless steel wall mounting bracket 71123339

Stainless steel pipe mounting bracket 71123342

Documentation
• Operating instructions "iTEMP TMT84" (BA00257R/09/en) and associated Brief Operating
Instructions "iTEMP TMT84" (KA00258R/09/a2)
• Ex supplementary documentation:
ATEX II 1G Ex ia IIC: XA00069R/09/a3
ATEX II 2(1)G Ex ia IIC: XA01012T/09/a3
ATEX II 2G Ex d IIC and ATEX II 2D Ex tb IIIC: XA01007T/09/a3
• Operating instructions "Display TID10" (BA262R/09/c4)
• Guidelines for planning and commissioning "PROFIBUS® DP/PA" (BA034S/04/en)

20 Endress+Hauser
TMT84

Endress+Hauser 21
www.addresses.endress.com